Mikrotikls SIA QRTG2SHPND DIGITAL TRANSMISSION SYSTEM User Manual

Mikrotikls SIA DIGITAL TRANSMISSION SYSTEM

a href="https://usermanual.wiki/Mikrotikls-SIA" itemprop="url"> Mikrotikls SIA >

User Manual

Seewww.routerboard.com formore information. Contactsupport@mikrotik.com forsupportquestions. 21/08/13RouterBOARD QRTG2SHPnDQuick Setup Guide and Warranty InformationThe RouterBOARD QRT comes as acomplete kit. Itincludes abuiltin802.11b/g/n dual chain wireless device, and adual polarization17dBi antenna. Ithas one Gigabit Ethernetconnector whichsupports MDIXauto detection.First use1. Connect anEthernet cable tothe port behindthe small plastic door2. The QRT accepts 24V PassivePoEfrom aPoEinjector3. The default IPaddress from LAN is 192.168.88.1forconfiguration from a web browser4. Username is admin and thereis no passwordPoweringThe device accepts powering from the Ethernetport(Passive PoE) 830V DC. Package contains a24Vadapter. Maximum power consumption of the device is 21W @24V. sBootingprocessInitial connection has to be done viathe Ethernetcable. Open 192.168.88.1inyourwebbrowser.Username is admin and there is no password. In case IP connection is notavailable, Winbox can be usedto connectto the MAC address of the device. More information here:http://wiki.mikrotik.com/wiki/First_time_startupIn case you wish to bootthe device from network, for example to use MikroTik Netinstall, hold theRESET button of the device when starting ituntilthe LED lightturns off, and Metal will startto lookfor Netinstall servers.MountingThe QRT box contains several parts thatneed to beassembled. Please follow this process:Start by attaching thetwo polebrackets (A) to theswivel adjuster (B), by using thefour provided screws(use a PH1 screwdriver).AB
Seewww.routerboard.com formore information. Contactsupport@mikrotik.com forsupportquestions. 21/08/13Next,put the twoUbolts (C) aroundthe mast or pole, andguidethem through the holes on the swivel adjuster (D).Then, tightenthe Ubolts, eachwithone regular washer, one spring washer, andone nut,asshownintheimagetothe right. All nuts needtobetightened using a size 10 (3/8 in)wrench.Now take the mounting bracket (E), and put it on to theback of the antenna. Use one rubber ring, one washer, andone nut foreach of the builtin bolts (in that order).Finally, attach theswivel adjuster to themountingbracket. Use the long bolt intheposition (F). Putone regular washer, andone spring washer ontotheshorter screws, then put them in positions(G). Donot tightentoomuch, as youneedtoadjust theantennanow.Once antenna level and angle are adjustedaccording to thewireless signal in software, tightenall nuts.Note the degrees of angle forfuturereference.CDFEGG
Download:
Mirror Download [FCC.gov]
Document ID2194104
Application IDBgfP2xiWv+Fj1MmkDawa2A==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize37.54kB (469243 bits)
Date Submitted2014-02-19 00:00:00
Date Available2014-02-19 00:00:00
Creation Date2014-02-12 19:00:41
Producing Softwareitext-paulo-155 (itextpdf.sf.net-lowagie.com)
Document Lastmod2014-02-12 19:00:41
Document TitleUser Manual
Document Creatorpdftk 1.44 - www.pdftk.com
FCC ID Filing: TV7QRTG2SHPND

Navigation menu