Mikrotikls SIA R11E5HM 5 GHz Unlicensed National Information Infrastructure Transmitter User Manual

Mikrotikls SIA 5 GHz Unlicensed National Information Infrastructure Transmitter

User Manual

R11e-5HnDThe R11e-5HnD is a miniPCIe format wireless interface that can operate in the 5GHz wireless spectrum. The card features two MMCX antennaconnectors. Assembly and mountingThe card is a mini PCIe full length format. Unplug the host device from power, and remove the preinstalled screws from the two locations wherethe card will be inserted. Insert the card at a slight angle, with the connector end first, push it slightly, so that it clicks into place. Lower the carduntil it is parallel to the motherboard and then use the two screws to fasten it in place. Attach the antenna to the card antenna connectors. ConfigurationThe device will be automatically recognized when used in a RouterOS powered device. Configuration can be set in the “Wireless” menu. Moreinformation about using RouterOS can be found in our documentation: http://mt.lv/help Operating system supportThe device is tested with RouterOS v6 and above. It might be compatible with other operating systems, but drivers are not included with thecard. List of approved antennas for 5GHz:•Omni Directional, MT-482016/N/A, 9 dBi;See www.routerboard.com for more information. Contact support@mikrotik.com 29-Jan-19
Federal Communication Commission Interference Statement (FCC ID: TV7R11E5HM)This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed andused in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or television reception, which can be determinedby turning the equipment off and on, the user is encouraged to try to correct the interference by oneof the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•Consult the dealer or an experienced radio/TV technician for help.FCC Caution: Any changes or modifications not expressly approved by the party responsible forcompliance could void the user’s authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) This device may not cause harmful interference, and (2) this device must accept anyinterference received, including interference that may cause undesired operation.This device and its antenna must not be co-located or operation in conjunction with any otherantenna or transmitter.IMPORTANT: Exposure to Radio Frequency Radiation.0,20 m minimum distance has to be maintained between the antenna and the occupational user and0,20m to general public. Under such configuration, the FCC radiation exposure limits set forth for anpopulation/uncontrolled environment can be satisfied.List of approved antennas for 5GHz:•Omni Directional, MT-482016/N/A, 9 dBi;Antenna Installation. WARNING: It is installer's responsibility to ensure that when using theauthorized antennas in the United States (or where FCC rules apply); only those antennas certifiedwith the product are used. The use of any antenna other than those certified with the product isexpressly forbidden in accordance to FCC rules CFR47 part 15.204. The installer should configure theoutput power level of antennas, according to country regulations and per antenna type. Professional installationis required of equipment with connectors to ensure compliance with health and safety issues.See www.routerboard.com for more information. Contact support@mikrotik.com 29-Jan-19
OEM statement. This module is intended for OEM installations only. As such the OEM integrator is responsible for ensuring that the end-user has no manual instructions to remove installor modify the module. This module is limited to installations in mobile or fixed applications. OEMintegrators may utilize antennas of like an equal or lesser gain as appearing in the list in thisdocument (reference 47 CFR, paragraph 15.204(c)(4) for further information on this topic. TheMikroTik OEM RF Module complies with Part 15 of the FCC rules and regulations.The Grantee will provide guidance to the Host Manufacturer in ensuring compliance with the Part 15Subpart B requirements. OEM Modules have been certified by the FCC for use with other products without any furthercertification (as per FCC section 2.1091). Separate approval is required for other operatingconfigurations including portable configurations with respect to 47CFR paragraph 2.1093 anddifferent antenna configurations. The OEM is required to comply with all 47CFR labeling instructionsand requirements for the finished products.Changes or modifications not expressly approved by MikroTik could void the OEM authority to installor operate the equipment. OEMs must test their final product to comply with unintentional radiators(FCC section 15.107 and 15.109) before declaring compliance of their final product to Part 15 of theFCC Rules. WARNING: the OEM must ensure that the FCC labeling requirements are met. This includes aclearly visible label on the outside of the OEM enclosure specifying the appropriate MikroTik OEM RFModule FCC identifier for this product as well as any other required FCC notices as presented below. Contains FCC ID: TV7R11E5HM This enclosed device complies with 47CFR paragraph 15 C of the FCC rules and regulations.Operation is subject to the following two conditions: (1) this device may not cause harmfulinterference, and (2) this device must accept any interference received, including interferencethat may cause undesired operation. Labeling and text information should be of a size of type large enough to be readily legible,consistent with the dimensions of the equipment and the label. WARNING: This device has been tested with a MMCX connector and antennas as listed in the tablebelow. When integrated into the OEM products, these fixed antennas require professionalinstallation. Preventing end users from replacing them with non-compliant antennas. List of approved antennas for 5GHz:•Omni Directional, MT-482016/N/A, 9 dBi;Antennas of same type and lower gain than those listed above may be used in compliance withcertification. See www.routerboard.com for more information. Contact support@mikrotik.com 29-Jan-19
Industry Canada (IC:7442A-R11E5HM) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject tothe following two conditions: (1) this device may not cause interference, and (2) this device mustaccept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doitpas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillageradioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. LE-LAN device restriction:LE-LAN devices are restricted to indoor operation only in the band 5150-5250 MHz.However, original equipment manufacturer (OEM) devices, which are installed in vehiclesby vehicles manufacturers, are permitted;Users should also be advised that high-power radars are allocated as primary users (i.e.priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radarscould cause interference and/or damage to LE-LAN devices.les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont réservés uniquementpour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable auxsystèmes de satellites mobiles utilisant les mêmes canauxLes utilisateurs devraient aussi être avisés, d’une part, que les utilisateurs de radars dehaute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) desbandes de 5 250 à 5 350 MHz et de 5 650 à 5 850 MHz et, d’autre part, que ces radarspourraient causer du brouillage et/ou des dommages aux dispositifs de RL-ELThis radio transmitter (identify the device by certification number or model number ifCategory II) has been approved by Industry Canada to operate with the antenna typeslisted below with the maximum permissible gain indicated. Antenna types not includedin this list, having a gain greater than the maximum gain indicated for that type, arestrictly prohibited for use with this device. List of approved antennas for 5GHz:•Omni Directional, MT-482016/N/A, 9 dBi;See www.routerboard.com for more information. Contact support@mikrotik.com 29-Jan-19

Navigation menu