Mikrotikls SIA R2SHPN Broadband Digital Transmission System Module User Manual USERS MANUAL
Mikrotikls SIA Broadband Digital Transmission System Module USERS MANUAL
USERS MANUAL
Federal Communication Commission Interference Statement
(FCC ID: TV7R2SHPN)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
● Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT: Exposure to Radio Frequency Radiation.
The maximum permissible exposure report has been created for this module, which shows the
minimum distances for public use as 142 cm when using a 24-dBi gain antenna. Under such
configuration, the FCC radiation exposure limits set forth for a general population/uncontrolled
environment can be satisfied.
OEM statement. This product is intended for OEM installations only. As such the OEM
integrator is responsible for ensuring that the end-user has no manual instructions to remove
install or modify the device. This product is limited to installations in mobile or fixed
applications. OEM integrators may utilize antennas of like and equal or lesser gain as
appearing in the table below (reference 47 CFR, paragraph 15.204(c)(4) for further
information on this topic. The MikroTik OEM product complies with Part 15 of the FCC rules and
regulations.
OEM product have been authorized by the FCC for use when placed inside computer enclosure.
Additional testing or approval may be required for other operating configurations including
portable configurations with respect to 47CFR paragraph 2.1093 and different antenna
configurations. The OEM is required to comply with all 47CFR labeling instructions and
requirements for the finished products.
Changes or modifications not expressly approved by MikroTik could void the authority to install
or operate the equipment. OEMs must test their final product to comply with unintentional
radiators (FCC section 15.107 and 15.109) before declaring compliance of their final product to
Part 15 of the FCC Rules.
WARNING: the OEM must ensure that the FCC labeling requirements are met. Labeling and
text information should be of a size and of type large enough to be readily legible, consistent
with the dimensions of the equipment and the label.
WARNING: This device has been tested with a MMCX connector and antennas as listed in the
table below. When integrated into the OEM products, these fixed antennas require professional
installation. Preventing end users from replacing them with non-compliant antennas.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
This device and its antenna must not be co-located or operation in conjunction with any other
antenna or transmitter.
List of approved antennas:
Omni Directional, 130K-D-1131-150K(WS), 2dBi;
Omni Directional, WLO-2450-15, 15 dBi;
Omni Directional HP, ODH 24-13, 13dBi;
Panel, WLP-2450-20, 20 dBi;
Sector, SA-24-90-17-WB, 17 dBi;
Dish, DC 24-HD-PFIP, 24 dBi;
Antennas of same type and lower gain than those listed above may be used in compliance with
certification.
Antenna Installation
WARNING: It is installer's responsibility to ensure that when using the authorized antennas in
the United States (or where FCC rules apply); only those antennas certified with the product
are used. The use of any antenna other than those certified with the product is expressly
forbidden in accordance to FCC rules CFR47 part 15.204. The installer should configure the
output power level of antennas, according to country regulations and per antenna type.
Professional installation is required of equipment with connectors to ensure compliance with
health and safety issues. For transmitter settings when using the above listed antennas it is
important to include the additional reduction of cable loss.
Antenna
Model
Gain (dBi)
Maximum Transmit
Power Setting (dBm)
Gain antenna below 6 dBi
130K-D-1131-
150K(WS)
2
28
Omni Directional
WLO-2450-15
15
25
Omni Directional HP
ODH 24-13
13
26
Panel
WLP-2450-20
20
23
Sector
SA 24-90-17-WB
17
24
Dish
DC 24-HD-PFIP
24
22