Mikrotikls SIA RB962-5ACT2NT Unlicensed National Information Infrastructure TX User Manual

Mikrotikls SIA Unlicensed National Information Infrastructure TX Users Manual

Contents

Users Manual

RouterBOARD hAP ac Quick Setup Guide and Warranty InformationThe hAP is a simple home wireless access point. It is configured out of the box, you can simply plug in your internetcable and start using wireless internet. We recommend you to set up a password to secure your device, followthese stepsConnecting1. Connect your Internet cable to port 1, and local network PCs to ports 2-52. Set your computer IP configuration to automatic (DHCP)3. Wireless “access point” mode is enabled by default, connect to the wireless network name which startswith “MikroTik”. Log into your router and configure a the Wireless password and router password to secureyour wireless network and access to the router4. Default IP address from the local network is 192.168.88.1, open this address in your web browser to startconfiguration. The username is admin and there is no password5. The Ether5 port suports PoE output for powering other RouterBOARD devices. The port has auto detectionfeature, so you can connect Laptops and other non-PoE devices without damaging them. The PoE onEther5 outputs approximately 2V below input voltage, and supports up to 0.58A (So provided 24V PSU willprovide 22V/0.58A output to the Ether5 PoE port). PoweringThe board accepts powering from the power jack or from the first Ethernet port (Passive PoE):direct-input power jack (5.5mm outside and 2mm inside, female, pin positive plug) accepts 8-30V DCfirst Ethernet port accepts passive Power over Ethernet accepts 8-30V DCThe power consumption under maximum load can reach 5WBooting processInitial connection has to be done via the Ethernet cable. Open 192.168.88.1 in your web browser. The username isadmin and there is no password. In case IP connection is not available, Winbox can be used to connect to theMAC address of the device. More information here: http://wiki.mikrotik.com/wiki/First_time_startup In case youwish to boot the device from network, for example to use MikroTik Netinstall, hold the RESET button of the devicewhen starting it until the LED light turns off, and unit will start to look for Netinstall servers.Extension Slots and PortsFive individual 10/100 Ethernet ports, supporting automatic cross/straight cable correction (Auto MDI/X), soyou can use either straight or cross-over cables for connecting to other network devices. Integrated Wireless 2.4GHz and 5GHz 802.11a/b/g/n/ac, simultaneous dual band radio with onboard PIFantennas, max gain 1.5dBiButtons and JumpersRouterBOOT reset button (RESET, front panel) has three functions:oHold this button during boot time until LED light starts flashing, release the button to resetRouterOS configuration (total 5 seconds)oKeep holding for 5 more seconds, LED turns solid, release now to turn on CAPs mode (total 10 seconds)See www.routerboard.com for more information. Contact support@mikrotik.com 16-Aug-16
oOr Keep holding the button for 5 more seconds until until LED turns off, then release it to make the RouterBOARD look for Netinstall servers (total 15 seconds)Operating System SupportCurrently tested operating system is MikroTik RouterOS starting from version v6.28Copyright and Warranty informationCopyright MikroTikls SIA. This document contains information protected by copyright law. No part of it may bereproduced or transmitted in any form without prior written permission from the copyright holder. RouterBOARD,RouterOS, RouterBOOT and MikroTik are trademarks of MikroTikls SIA. All trademarks and registered trademarksappearing in this document are the property of their respective holders.Hardware. MikroTik warrants all RouterBOARD series equipment for the term of twelve (12) months from theshipping date to be free of defects in materials and workmanship under normal use and service, except in case ofdamage caused by mechanical, electrical or other accidental or intended damages caused by improper use or dueto wind, rain, fire or other acts of nature.To return failed units to MikroTik, you must perform the following RMA (Return Merchandise Authorization)procedure. Follow the instructions below to save time, efforts, avoid costs, and improve the speed of the RMAprocess.1. If you have purchased your product from a MikroTik Reseller, please contact the Reseller companyregarding all warranty and repair issues, the following instructions apply ONLY if you purchased yourequipment directly from MikroTik in Latvia.2. MikroTik does not offer repairs for products that are not covered by warranty. Exceptions can be made for:CCR1016-12G, CCR1016-12G-BU, CCR1036-12G-4S, RB1100, RB1100AH, RB1100AHx2, RB1200,RB600, RB600A and RB800 as a paid service (fees apply).3. Out-of-warranty devices and devices not covered by warranty sent to Mikrotik will be returned to the senderat sender's cost. If the customer has not organized return of such rejected devices within 12 months fromthe day of arrival, MikroTik has the right to discard them. RMA Instructions are located on our webpage here: http://rma.mikrotik.comThis document is provided “as is” without a warranty of any kind, expressed or implied, including, but not limited to,the implied warranty of merchantability and fitness for a particular purpose. The manufacturer has made everyeffort to ensure the accuracy of the contents of this document, however, it is possible that it may contain technicalinaccuracies, typographical or other errors. No liability is assumed for any inaccuracy found in this publication, norfor direct or indirect, incidental, consequential or other damages that may result from such an inaccuracy, including,but not limited to, loss of data or profits. Please report any inaccuracies found to support@mikrotik.comSee www.routerboard.com for more information. Contact support@mikrotik.com 16-Aug-16
Federal Communication Commission InterferenceStatement (FCC ID: TV7RB962-5ACT2NT)This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed andused in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or television reception, which can be determinedby turning the equipment off and on, the user is encouraged to try to correct the interference by oneof the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•Consult the dealer or an experienced radio/TV technician for help.FCC Caution: Any changes or modifications not expressly approved by the party responsible forcompliance could void the user’s authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) This device may not cause harmful interference, and (2) this device must accept anyinterference received, including interference that may cause undesired operation.This device and its antenna must not be co-located or operation in conjunction with any otherantenna or transmitter.IMPORTANT: Exposure to Radio Frequency Radiation.20 cm minimum distance has to be maintained between the antenna and user. Under suchconfiguration, the FCC radiation exposure limits set forth for an population/uncontrolled environmentcan be satisfied.Antenna Installation. WARNING: It is installer's responsibility to ensure that when using theauthorized antennas in the United States (or where FCC rules apply); only those antennas certifiedwith the product are used. The use of any antenna other than those certified with the product isexpressly forbidden in accordance to FCC rules CFR47 part 15.204. The installer should configure theoutput power level of antennas, according to country regulations and per antenna type. Professionalinstallation is required of equipment with connectors to ensure compliance with health and safetyissues. Industry Canada (IC:7442A-9625AC) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject tothe following two conditions: (1) this device may not cause interference, and (2) this device mustaccept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doitpas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillageradioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. See www.routerboard.com for more information. Contact support@mikrotik.com 16-Aug-16All operations are to be maintained within the band of operation under all conditions of normal operation
LE-LAN device restriction:The device for operation in the band 5150–5250 MHz is only for indoor use to reduce thepotential for harmful interference to co-channel mobile satellite systems;Users should also be advised that high-power radars are allocated as primary users (i.e.priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radarscould cause interference and/or damage to LE-LAN devices.les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont réservés uniquementpour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable auxsystèmes de satellites mobiles utilisant les mêmes canauxLes utilisateurs devraient aussi être avisés, d’une part, que les utilisateurs de radars dehaute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) desbandes de 5 250 à 5 350 MHz et de 5 650 à 5 850 MHz et, d’autre part, que ces radarspourraient causer du brouillage et/ou des dommages aux dispositifs de RL-ELSee www.routerboard.com for more information. Contact support@mikrotik.com 16-Aug-16
CE Declaration of ConformityFull Declaration of Conformity (DoC) may be obtained by visiting this web page: http://routerboard.com/doc/[EN] English Hereby, MIKROTĪKLS SIA declares that this ROUTERBOARD is in compliance with the essential requirements andother relevant provisions of Directive 1999/5/EC.[BG]BulgarianС настоящето, MIKROTĪKLS SIA декларира, че ROUTERBOARD е в съответствие със съществените изискванияи другитеприложими разпоредби на Директива 1999/5/EC.[CZ] Czech MIKROTĪKLS SIA tímto prohlašuje, že ROUTERBOARD splňuje základní požadavky a všechna příslušná ustanoveniSměrnice 1999/5/ES.[DK] Danish Undertegnede MIKROTĪKLS SIA erklærer herved, at følgende udstyr ROUTERBOARD overholder de væsentlige kravog øvrige relevante krav i direktiv 1999/5/EF.[DE] German Hiermit erklärt MIKROTĪKLS SIA dass sich das Gerät ROUTERBOARD in Übereinstimmung mit den grundlegendenAnforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG be\ndet.[EE] EstonianKäesolevaga kinnitab MIKROTĪKLS SIA seadme ROUTERBOARD vastavust direktiivi 1999/5/EÜ põhinõuetele janimetatud direktiivist tulenevatele teistele asjakohastele sätetele.[GR] Greek ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Ο ΚΑΤΑΣΚΕΥΑΣΤΗΣ MIKROTĪKLS SIA ΔΗΛΩΝΕΙ ΟΤΙ ROUTERBOARD ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ[ES] Spanish Por la presente, MIKROTĪKLS SIA declara que este ROUTERBOARD cumple con los requisitos esenciales y otrasexigencias relevantes de la Directiva 1999/5/EC.[IT] Italian Con la presente MIKROTĪKLS SIA dichiara che questo ROUTERBOARD è conforme ai requisiti essenziali ed alle altredisposizioni pertinenti stabilite dalla direttiva 1999/5/CE.[LV] Latvian Ar šo MIKROTĪKLS SIA deklarē, ka ROUTERBOARD atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar tosaistītajiem noteikumiem.[LT]LithuanianŠiuo MIKROTĪKLS SIA deklaruoja, kad šis ROUTERBOARD atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvosnuostatas[HU]HungarianA MIKROTĪKLS SIA ezzennel kijelenti, hogy a ROUTERBOARD típusú beren-dezés teljesíti az alapvetőkövetelményeket és más 1999/5/EK irányelvben meghatározott vonatkozó rendelkezéseket.[NL] Dutch Hierbij verklaart MIKROTĪKLS SIA dat het toestel l ROUTERBOARD in overeenstemming is met de essentiële eisen ende andere relevante bepalin-gen van richtlijn 1999/5/EG.[PL] Polish Niniejszym MIKROTĪKLS SIA deklaruje że ROUTERBOARD jest zgodny z zasadniczymi wymaganiami i innymiwłaściwymi postanowieniami Dyrektywy 1999/5/EC.[PT]PortugueseEu, MIKROTĪKLS SIA declaro que o ROUTERBOARD cumpre os requisitos essenciais e outras provisões relevantes daDirectiva 1999/5/EC.[RO]RomanianPrin prezenta, MIKROTĪKLS SIA declară că aparatul ROUTERBOARD este în conformitate cu cerinţele esenţiale şi cualte prevederi pertinente ale Directivei 1999/5/CE..[SK] Slovak MIKROTĪKLS SIA týmto vyhlasuje, že ROUTERBOARD spĺňa základné požiadavky a všetky príslušné ustanoveniaSmernice 1999/5/ES.[SI]SlovenianMIKROTĪKLS SIA izjavlja, da je ta ROUTERBOARD v skladu z bistvenimi zahtevami in drugimi relevantnimi določilidirektive 1999/5/ES.[FI] Finish MIKROTĪKLS SIA vakuuttaa täten että ROUTERBOARD tyyppinen laite on direktiivin 1999/5/EY oleellistenvaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.[SE] Swedish Härmed intygar MIKROTĪKLS SIA att denna RouterBOARD är i överensstämmelse med de väsentliga egenskapskrav och övrigarelevanta bestämmelser som framgår av direktiv 1999/5/EG.[NO]NorwegianMIKROTĪKLS SIA Erklærer herved at ROUTERBOARD er i samsvar med de grunnleggende krav og øvrige relevantekrav i direktiv 1999/5/EF.EN. Instruction manual: Connect the power adapter to turn on the device. Open 192.168.88.1 in your web browser, to configure it. Moreinformation on http://wiki.mikrotik.com BG. Инструкция: Свържете адаптера на захранване, за да включите устройството. Отворете192.168.88.1 в уеб браузър, за да настроите продукта. Повече информация в http://wiki.mikrotik.com CZ. Návod k použití: Připojtenapájecí adaptér k zapnutí přístroje. Otevřete 192.168.88.1 ve webovém prohlížeči pro konfiguraci produktu. Více informací najdete vhttp://wiki.mikrotik.com DK. Instruktionsbog: Tilslut strømadapteren for at tænde for enheden. Åbn 192.168.88.1 i en webbrowser til atkonfigurere produktet. Mere information i http://wiki.mikrotik.com FR. Mode d'emploi: Connectez l'adaptateur d'alimentation pour allumerl'appareil. Ouvrez 192.168.88.1 dans un navigateur Web pour configurer le produit. Plus d'informations dans http://wiki.mikrotik.com DE.Bedienungsanleitung: Verbinden Sie das Netzteil, um das Gerät einzuschalten. Öffnen Sie 192.168.88.1 in einem Web-Browser, um dasProdukt zu konfigurieren. Weitere Informationen im http://wiki.mikrotik.com EE. Kasutusjuhend: Ühendage toiteadapter seadmesisselülitamiseks. Avatud 192.168.88.1 in veebilehitseja seadistada toodet. Rohkem teavet http://wiki.mikrotik.com ES. Manual deinstrucciones: Conecte el adaptador de alimentación para encender la unidad. Abra 192.168.88.1 en un navegador web para configurar elproducto. Más información en http://wiki.mikrotik.com IT. Manuale di istruzioni: Collegare l'adattatore di alimentazione per accendere l'unità.Aprire 192.168.88.1 in un browser Web per configurare il prodotto. Maggiori informazioni in http://wiki.mikrotik.com LV. Lietošanas instrukcija:Pievienojiet Strāvas adapteri, lai ieslēgtu ierīci. Atvērt 192.168.88.1 ar interneta pārlūku, lai konfigurētu produktu. Plašāka informācijahttp://wiki.mikrotik.com LT. Naudojimosi instrukcija: Prijunkite maitinimo adapterį įjunkite įrenginį. Į interneto naršyklę 192.168.88.1 Atidarykitegalite konfigūruoti gaminį. Daugiau informacijos rasite http://wiki.mikrotik.com HU. Használati utasítás: Csatlakoztassa a hálózati adaptert akészülék bekapcsolásához. Megnyitása 192.168.88.1 egy webböngészőben beállítani a terméket. Több információ http://wiki.mikrotik.com NL.Handleiding: Sluit voedingsadapter aan op het apparaat in te schakelen. Open 192.168.88.1 in een webbrowser om het product teconfigureren. Meer informatie in http://wiki.mikrotik.com PL. Instrukcja obsługi: Podłącz adapter zasilania, aby włączyć urządzenie. Otwórz192.168.88.1 w przeglądarce internetowej, aby skonfigurować urządzenie. Więcej informacji w http://wiki.mikrotik.com PT. Manual deinstruções: Conecte o adaptador de alimentação para ligar o aparelho. Abra 192.168.88.1 em um navegador da web para configurar oproduto. Mais informações em http://wiki.mikrotik.com RO. Instruc iuni de utilizareț : Conecta iț adaptorul de alimentare pentru a porni aparatul.Deschide 192.168.88.1 într-un browser web pentru a configura produsul. Mai multe informa iiț în http://wiki.mikrotik.com SK. Návod na použitie:Pripojte napájací adaptér k zapnutiu prístroja. Otvorte 192.168.88.1 vo webovom prehliadači pre konfiguráciu produktu. Viac informácií nájdetev http://wiki.mikrotik.com SI. Navodila: Priključite napajalnik za vklop naprave. Odprite 192.168.88.1 v spletnem brskalniku nastaviti izdelek. Večinformacij v http://wiki.mikrotik.com FI. Käyttöohje: Kytke virtalähde päälle laitteen. Avaa 192.168.88.1 in selaimen määrittää tuotteen. Lisäätietoa http://wiki.mikrotik.com SE. Instruktionsmanual: Anslut nätadaptern för att slå på enheten. Öppna 192.168.88.1 i en webbläsare för attSee www.routerboard.com for more information. Contact support@mikrotik.com 16-Aug-16
konfigurera produkten. Mer information på http://wiki.mikrotik.com NO. Bruksanvisningen: Koble strømadapteren for å slå på enheten. Åpne192.168.88.1 i en nettleser for å konfigurere produktet. Mer informasjon på http://wiki.mikrotik.com GR. εγχειρίδιο οδηγιών: Συνδέστε τονπροσαρμογέα τροφοδοσίας για να ενεργοποιήσετε τη μονάδα. Ανοίξτε 192.168.88.1 σε ένα πρόγραμμα περιήγησης στο Web για ναδιαμορφώσετε το προϊόν. Περισσότερες πληροφορίες στο http://wiki.mikrotik.comSee www.routerboard.com for more information. Contact support@mikrotik.com 16-Aug-16

Navigation menu