Mikrotikls SIA RBCM2ND Digital Transmission System 2412-2462 MHz User Manual

Mikrotikls SIA Digital Transmission System 2412-2462 MHz

User Manual

RouterBOARD cAP 2nDQuick Setup Guide and Warranty InformationThe cAP is a small AP device with 1 ethernet port, it supports powering by PoE. Connecting1. Connect your Internet cable to port 12. Set computer/router IP configuration to automatic (DHCP)3. Wireless AP mode is enabled by default, you can connect to the SSID “MikroTik”. Log into your router fromyour web browser by opening 192.168.88.1 in the address barPoweringThe device accepts powering from Ethernet port (Passive PoE only). Under maximum load, the power consumptionof this device is 4W (when not using PoE output)Booting processThe device is preinstalled with MikroTik RouterOS software. It can be configured in several ways.This device doesn't come fitted with a Serial Port connector, so initial connection has to be done via the Ethernetcable. Connect to wireless SSID “MikroTik” and open 192.168.88.1 in your web browser. Username is admin andthere is no password. In case IP connection is not available, Winbox can be used to connect to the MAC address ofthe device. More information here: http://wiki.mikrotik.com/wiki/First_time_startupIn case you wish to boot the device from network, for example to use MikroTik Netinstall, hold the RESET button ofthe device when starting it until the LED light turns off, then release the button and the device will start looking forNetinstall servers.By default, the device is preconfigured with a simple firewall on the WAN port, this configuration can be viewed whenfirst connecting to the Router via Winbox. It will ask whether to keep this configuration or clean it to use your own.LAN/WLAN ports have DHCP server enabled.Extension Slots and PortsOne 10/100 Ethernet port, supporting automatic cross/straight cable connection (Auto MDI/X), so you canuse either straight or cross-over cables for connecting to other network devices. One Integrated Wireless 2.4GHz 802.11b/g/n device with CPE/AP mode support, two soldered PIFantennas, max gain 2dBiResetting the deviceIn case you wish to return the device to its original configuration, you can use the RESET button which is located tothe left of the Ethernet port. Hold this button during boot time until LED lights start flashing, then release the button toreset RouterOS configuration. You can use this procedure if you have forgotten the password to access thedevice, or simply wish to return the unit to its default configuration state.See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 8-Aug-16
Buttons and JumpersThe reset button has three functions:Hold this button during boot time until LED light starts flashing, release the button to reset RouterOS configuration (total 5 seconds)Keep holding for 5 more seconds, LED turns solid, release now to turn on CAPs mode (total 10 seconds)Or Keep holding the button for 5 more seconds until until LED turns off, then release it to make the RouterBOARD look for Netinstall servers (total 15 seconds)Operating System SupportCurrently tested operating system is MikroTik RouterOS starting from version 6.20. It is not suggested to downgradebelow the software version the unit was delivered with. Copyright and Warranty informationCopyright MikroTikls SIA. This document contains information protected by copyright law. No part of it may bereproduced or transmitted in any form without prior written permission from the copyright holder. RouterBOARD,RouterOS, RouterBOOT and MikroTik are trademarks of MikroTikls SIA. All trademarks and registered trademarksappearing in this document are the property of their respective holders.Hardware. MikroTik warrants all RouterBOARD series equipment for the term of twelve (12) months from theshipping date to be free of defects in materials and workmanship under normal use and service, except in case ofdamage caused by mechanical, electrical or other accidental or intended damages caused by improper use or due towind, rain, fire or other acts of nature.To return failed units to MikroTik, you must perform the following RMA (Return Merchandise Authorization)procedure. Follow the instructions below to save time, efforts, avoid costs, and improve the speed of the RMAprocess.1. If you have purchased your product from a MikroTik Reseller, please contact the Reseller company regarding allwarranty and repair issues, the following instructions apply ONLY if you purchased your equipment directly fromMikroTik in Latvia.2. MikroTik does not offer repairs for products that are not covered by warranty. Exceptions can be made for:CCR1016-12G, CCR1016-12G-BU, CCR1036-12G-4S, RB1100, RB1100AH, RB1100AHx2, RB1200, RB600,RB600A and RB800 as a paid service (fees apply).3. Out-of-warranty devices and devices not covered by warranty sent to Mikrotik will be returned to the senderat sender's cost. If the customer has not organized return of such rejected devices within 12 months from the dayof arrival, MikroTik has the right to discard them. RMA Instructions are located on our webpage here: http://rma.mikrotik.comThis document is provided “as is” without a warranty of any kind, expressed or implied, including, but not limited to,the implied warranty of merchantability and fitness for a particular purpose. The manufacturer has made every effortto ensure the accuracy of the contents of this document, however, it is possible that it may contain technicalinaccuracies, typographical or other errors. No liability is assumed for any inaccuracy found in this publication, nor fordirect or indirect, incidental, consequential or other damages that may result from such an inaccuracy, including, butnot limited to, loss of data or profits. Please report any inaccuracies found to support@mikrotik.comSee www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 8-Aug-16
Federal Communication Commission Interference Statement (FCC ID: TV7RBCM2ND)This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and usedin accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or television reception, which can be determinedby turning the equipment off and on, the user is encouraged to try to correct the interference by oneof the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•Consult the dealer or an experienced radio/TV technician for help.FCC Caution: Any changes or modifications not expressly approved by the party responsible forcompliance could void the user’s authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) This device may not cause harmful interference, and (2) this device must accept anyinterference received, including interference that may cause undesired operation.This device and its antenna must not be co-located or operation in conjunction with any other antennaor transmitter.IMPORTANT: Exposure to Radio Frequency Radiation.This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolledenvironment. This equipment should be installed and operated with a minimum distance of 20cmbetween the radiator and any part of your body.Antenna Installation. WARNING: It is installer's responsibility to ensure that when using theauthorized antennas in the United States (or where FCC rules apply); only those antennas certifiedwith the product are used. The use of any antenna other than those certified with the product isexpressly forbidden in accordance to FCC rules CFR47 part 15.204. The installer should configure theoutput power level of antennas, according to country regulations and per antenna type. Professionalinstallation is required of equipment with connectors to ensure compliance with health and safetyissues. Industry Canada (IC:7442A-CM2ND) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject tothe following two conditions: (1) this device may not cause interference, and (2) this device mustaccept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exemptsde licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pasproduire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectriquesubi, même si le brouillage est susceptible d'en compromettre le fonctionnement. See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 8-Aug-16
CE Declaration of ConformityFull Declaration of Conformity (DoC) may be obtained by visiting this web page: http://routerboard.com/doc/[EN] English Hereby, MIKROTĪKLS SIA declares that this ROUTERBOARD is in compliance with the essential requirements and other relevant provisions ofDirective 1999/5/EC.[BG] Bulgarian С настоящето, MIKROTĪKLS SIA декларира, че ROUTERBOARD е в съответствие със съществените изисквания и другитеприложимиразпоредби на Директива 1999/5/EC.[CZ] Czech MIKROTĪKLS SIA tímto prohlašuje, že ROUTERBOARD splňuje základní požadavky a všechna příslušná ustanoveni Směrnice 1999/5/ES.[DK] Danish Undertegnede MIKROTĪKLS SIA erklærer herved, at følgende udstyr ROUTERBOARD overholder de væsentlige krav og øvrige relevante krav idirektiv 1999/5/EF.[DE] German Hiermit erklärt MIKROTĪKLS SIA dass sich das Gerät ROUTERBOARD in Übereinstimmung mit den grundlegenden Anforderungen und den übrigeneinschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.[EE] Estonian Käesolevaga kinnitab MIKROTĪKLS SIA seadme ROUTERBOARD vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevateleteistele asjakohastele sätetele.[GR] Greek ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Ο ΚΑΤΑΣΚΕΥΑΣΤΗΣ MIKROTĪKLS SIA ΔΗΛΩΝΕΙ ΟΤΙ ROUTERBOARD ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ[ES] Spanish Por la presente, MIKROTĪKLS SIA declara que este ROUTERBOARD cumple con los requisitos esenciales y otras exigencias relevantes de laDirectiva 1999/5/EC.[IT] Italian Con la presente MIKROTĪKLS SIA dichiara che questo ROUTERBOARD è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilitedalla direttiva 1999/5/CE.[LV] Latvian Ar šo MIKROTĪKLS SIA deklarē, ka ROUTERBOARD atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.[LT] Lithuanian Šiuo MIKROTĪKLS SIA deklaruoja, kad šis ROUTERBOARD atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas[HU] Hungarian A MIKROTĪKLS SIA ezzennel kijelenti, hogy a ROUTERBOARD típusú beren-dezés teljesíti az alapvető követelményeket és más 1999/5/EKirányelvben meghatározott vonatkozó rendelkezéseket.[NL] Dutch Hierbij verklaart MIKROTĪKLS SIA dat het toestel l ROUTERBOARD in overeenstemming is met de essentiële eisen en de andere relevante bepalin-gen van richtlijn 1999/5/EG.[PL] Polish Niniejszym MIKROTĪKLS SIA deklaruje że ROUTERBOARD jest zgodny z zasadniczymi wymaganiami i innymi właściwymi postanowieniamiDyrektywy 1999/5/EC.[PT] Portuguese Eu, MIKROTĪKLS SIA declaro que o ROUTERBOARD cumpre os requisitos essenciais e outras provisões relevantes da Directiva 1999/5/EC.[RO] Romanian Prin prezenta, MIKROTĪKLS SIA declară că aparatul ROUTERBOARD este în conformitate cu cerinţele esenţiale şi cu alte prevederi pertinente aleDirectivei 1999/5/CE..[SK] Slovak MIKROTĪKLS SIA týmto vyhlasuje, že ROUTERBOARD spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.[SI] Slovenian MIKROTĪKLS SIA izjavlja, da je ta ROUTERBOARD v skladu z bistvenimi zahtevami in drugimi relevantnimi določili direktive 1999/5/ES.[FI] Finish MIKROTĪKLS SIA vakuuttaa täten että ROUTERBOARD tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivinmuiden ehtojen mukainen.[SE] Swedish Härmed intygar MIKROTĪKLS SIA att denna RouterBOARD är i överensstämmelse med de väsentliga egenskapskrav och övriga relevantabestämmelser som framgår av direktiv 1999/5/EG.[NO] Norwegian MIKROTĪKLS SIA Erklærer herved at ROUTERBOARD er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.EN. Instruction manual: Connect the power adapter to turn on the device. Open 192.168.88.1 in your web browser, to configure it. Moreinformation on http://wiki.mikrotik.com BG. Инструкция: Свържете адаптера на захранване, за да включите устройството. Отворете192.168.88.1 в уеб браузър, за да настроите продукта. Повече информация в http://wiki.mikrotik.com CZ. Návod k použití: Připojte napájecíadaptér k zapnutí přístroje. Otevřete 192.168.88.1 ve webovém prohlížeči pro konfiguraci produktu. Více informací najdete vhttp://wiki.mikrotik.com DK. Instruktionsbog: Tilslut strømadapteren for at tænde for enheden. Åbn 192.168.88.1 i en webbrowser til atkonfigurere produktet. Mere information i http://wiki.mikrotik.com FR. Mode d'emploi: Connectez l'adaptateur d'alimentation pour allumerl'appareil. Ouvrez 192.168.88.1 dans un navigateur Web pour configurer le produit. Plus d'informations dans http://wiki.mikrotik.com DE.Bedienungsanleitung: Verbinden Sie das Netzteil, um das Gerät einzuschalten. Öffnen Sie 192.168.88.1 in einem Web-Browser, um dasProdukt zu konfigurieren. Weitere Informationen im http://wiki.mikrotik.com EE. Kasutusjuhend: Ühendage toiteadapter seadmesisselülitamiseks. Avatud 192.168.88.1 in veebilehitseja seadistada toodet. Rohkem teavet http://wiki.mikrotik.com ES. Manual de instrucciones:Conecte el adaptador de alimentación para encender la unidad. Abra 192.168.88.1 en un navegador web para configurar el producto. Másinformación en http://wiki.mikrotik.com IT. Manuale di istruzioni: Collegare l'adattatore di alimentazione per accendere l'unità. Aprire192.168.88.1 in un browser Web per configurare il prodotto. Maggiori informazioni in http://wiki.mikrotik.com LV. Lietošanas instrukcija:Pievienojiet Strāvas adapteri, lai ieslēgtu ierīci. Atvērt 192.168.88.1 ar interneta pārlūku, lai konfigurētu produktu. Plašāka informācijahttp://wiki.mikrotik.com LT. Naudojimosi instrukcija: Prijunkite maitinimo adapterį įjunkite įrenginį. Į interneto naršyklę 192.168.88.1 Atidarykitegalite konfigūruoti gaminį. Daugiau informacijos rasite http://wiki.mikrotik.com HU. Használati utasítás: Csatlakoztassa a hálózati adaptert akészülék bekapcsolásához. Megnyitása 192.168.88.1 egy webböngészőben beállítani a terméket. Több információ http://wiki.mikrotik.com NL.Handleiding: Sluit voedingsadapter aan op het apparaat in te schakelen. Open 192.168.88.1 in een webbrowser om het product te configureren.Meer informatie in http://wiki.mikrotik.com PL. Instrukcja obsługi: Podłącz adapter zasilania, aby włączyć urządzenie. Otwórz 192.168.88.1 wprzeglądarce internetowej, aby skonfigurować urządzenie. Więcej informacji w http://wiki.mikrotik.com PT. Manual de instruções: Conecte oadaptador de alimentação para ligar o aparelho. Abra 192.168.88.1 em um navegador da web para configurar o produto. Mais informações emhttp://wiki.mikrotik.com RO. Instruc iuni de utilizareț : Conecta iț adaptorul de alimentare pentru a porni aparatul. Deschide 192.168.88.1 într-unbrowser web pentru a configura produsul. Mai multe informa iiț în http://wiki.mikrotik.com SK. Návod na použitie: Pripojte napájací adaptér kzapnutiu prístroja. Otvorte 192.168.88.1 vo webovom prehliadači pre konfiguráciu produktu. Viac informácií nájdete v http://wiki.mikrotik.com SI.Navodila: Priključite napajalnik za vklop naprave. Odprite 192.168.88.1 v spletnem brskalniku nastaviti izdelek. Več informacij vhttp://wiki.mikrotik.com FI. Käyttöohje: Kytke virtalähde päälle laitteen. Avaa 192.168.88.1 in selaimen määrittää tuotteen. Lisää tietoahttp://wiki.mikrotik.com SE. Instruktionsmanual: Anslut nätadaptern för att slå på enheten. Öppna 192.168.88.1 i en webbläsare för attkonfigurera produkten. Mer information på http://wiki.mikrotik.com NO. Bruksanvisningen: Koble strømadapteren for å slå på enheten. Åpne192.168.88.1 i en nettleser for å konfigurere produktet. Mer informasjon på http://wiki.mikrotik.com GR. εγχειρίδιο οδηγιών: Συνδέστε τονπροσαρμογέα τροφοδοσίας για να ενεργοποιήσετε τη μονάδα. Ανοίξτε 192.168.88.1 σε ένα πρόγραμμα περιήγησης στο Web για ναδιαμορφώσετε το προϊόν. Περισσότερες πληροφορίες στο http://wiki.mikrotik.com See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 8-Aug-16

Navigation menu