Mikrotikls SIA RBCM2ND Digital Transmission System 2412-2462 MHz User Manual

Mikrotikls SIA Digital Transmission System 2412-2462 MHz

a href="https://usermanual.wiki/Mikrotikls-SIA" itemprop="url"> Mikrotikls SIA >

User Manual

RouterBOARD cAP 2nDQuick Setup Guide and Warranty InformationThe cAP is a small AP device with 1 ethernet port, it supports powering by PoE. Connecting1. Connect your Internet cable to port 12. Set computer/router IP configuration to automatic (DHCP)3. Wireless AP mode is enabled by default, you can connect to the SSID “MikroTik”. Log into your router fromyour web browser by opening 192.168.88.1 in the address barPoweringThe device accepts powering from Ethernet port (Passive PoE only). Under maximum load, the power consumptionof this device is 4W (when not using PoE output)Booting processThe device is preinstalled with MikroTik RouterOS software. It can be configured in several ways.This device doesn't come fitted with a Serial Port connector, so initial connection has to be done via the Ethernetcable. Connect to wireless SSID “MikroTik” and open 192.168.88.1 in your web browser. Username is admin andthere is no password. In case IP connection is not available, Winbox can be used to connect to the MAC address ofthe device. More information here: http://wiki.mikrotik.com/wiki/First_time_startupIn case you wish to boot the device from network, for example to use MikroTik Netinstall, hold the RESET button ofthe device when starting it until the LED light turns off, then release the button and the device will start looking forNetinstall servers.By default, the device is preconfigured with a simple firewall on the WAN port, this configuration can be viewed whenfirst connecting to the Router via Winbox. It will ask whether to keep this configuration or clean it to use your own.LAN/WLAN ports have DHCP server enabled.Extension Slots and PortsOne 10/100 Ethernet port, supporting automatic cross/straight cable connection (Auto MDI/X), so you canuse either straight or cross-over cables for connecting to other network devices. One Integrated Wireless 2.4GHz 802.11b/g/n device with CPE/AP mode support, two soldered PIFantennas, max gain 2dBiResetting the deviceIn case you wish to return the device to its original configuration, you can use the RESET button which is located tothe left of the Ethernet port. Hold this button during boot time until LED lights start flashing, then release the button toreset RouterOS configuration. You can use this procedure if you have forgotten the password to access thedevice, or simply wish to return the unit to its default configuration state.See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 8-Aug-16
Buttons and JumpersThe reset button has three functions:Hold this button during boot time until LED light starts flashing, release the button to reset RouterOS configuration (total 5 seconds)Keep holding for 5 more seconds, LED turns solid, release now to turn on CAPs mode (total 10 seconds)Or Keep holding the button for 5 more seconds until until LED turns off, then release it to make the RouterBOARD look for Netinstall servers (total 15 seconds)Operating System SupportCurrently tested operating system is MikroTik RouterOS starting from version 6.20. It is not suggested to downgradebelow the software version the unit was delivered with. Copyright and Warranty informationCopyright MikroTikls SIA. This document contains information protected by copyright law. No part of it may bereproduced or transmitted in any form without prior written permission from the copyright holder. RouterBOARD,RouterOS, RouterBOOT and MikroTik are trademarks of MikroTikls SIA. All trademarks and registered trademarksappearing in this document are the property of their respective holders.Hardware. MikroTik warrants all RouterBOARD series equipment for the term of twelve (12) months from theshipping date to be free of defects in materials and workmanship under normal use and service, except in case ofdamage caused by mechanical, electrical or other accidental or intended damages caused by improper use or due towind, rain, fire or other acts of nature.To return failed units to MikroTik, you must perform the following RMA (Return Merchandise Authorization)procedure. Follow the instructions below to save time, efforts, avoid costs, and improve the speed of the RMAprocess.1. If you have purchased your product from a MikroTik Reseller, please contact the Reseller company regarding allwarranty and repair issues, the following instructions apply ONLY if you purchased your equipment directly fromMikroTik in Latvia.2. MikroTik does not offer repairs for products that are not covered by warranty. Exceptions can be made for:CCR1016-12G, CCR1016-12G-BU, CCR1036-12G-4S, RB1100, RB1100AH, RB1100AHx2, RB1200, RB600,RB600A and RB800 as a paid service (fees apply).3. Out-of-warranty devices and devices not covered by warranty sent to Mikrotik will be returned to the senderat sender's cost. If the customer has not organized return of such rejected devices within 12 months from the dayof arrival, MikroTik has the right to discard them. RMA Instructions are located on our webpage here: http://rma.mikrotik.comThis document is provided “as is” without a warranty of any kind, expressed or implied, including, but not limited to,the implied warranty of merchantability and fitness for a particular purpose. The manufacturer has made every effortto ensure the accuracy of the contents of this document, however, it is possible that it may contain technicalinaccuracies, typographical or other errors. No liability is assumed for any inaccuracy found in this publication, nor fordirect or indirect, incidental, consequential or other damages that may result from such an inaccuracy, including, butnot limited to, loss of data or profits. Please report any inaccuracies found to support@mikrotik.comSee www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 8-Aug-16
Download:
Mirror Download [FCC.gov]
Document ID3092412
Application IDjpGFJ74Zm+pmYpa5S+GZdg==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize18.7kB (233798 bits)
Date Submitted2016-08-09 00:00:00
Date Available2016-08-09 00:00:00
Creation Date2016-08-08 16:39:17
Producing SoftwareLibreOffice 5.1
Document Lastmod0000-00-00 00:00:00
Document TitleUser Manual
Document CreatorWriter
Document Author: Normis
FCC ID Filing: TV7RBCM2ND

Navigation menu