Mikrotikls SIA SXT-2ND MIMO BROADBAND DIGITAL TRANSMISSION SYSTEM User Manual SXTr2 2nD qgx
Mikrotikls SIA MIMO BROADBAND DIGITAL TRANSMISSION SYSTEM SXTr2 2nD qgx
User Manual
RouterBOARD SXT r2 2nD Quick Setup Guide and Warranty Information The RouterBOARD SXT r2 2nD comes as a complete set, and includes a built in 802.11b/g/n dual chain wireless device, and a dual polarization 16dBi antenna. It has one BASE-‐T 10/100 ethernet connector which supports MDI-‐X auto detection. First use 1. 2. 3. 4. Connect an Ethernet cable to the port behind the small plastic door The SXT accepts 24V Passive PoE from a PoE injector The default IP address from LAN is 192.168.88.1 for configuration Username is admin and there is no password Powering The board accepts powering from the Ethernet port (Passive PoE) 8-‐30V DC. Package contains a 24V adapter. Maximum power consumption of the device is 7W. Booting process Initial connection has to be done via the Ethernet cable. Open 192.168.88.1 in your web browser. Username is admin and there is no password. In case IP connection is not available, Winbox can be used to connect to the MAC address of the device. More information here: http://wiki.mikrotik.com/wiki/First_time_startup In case you wish to boot the device from network, for example to use MikroTik Netinstall, hold the RESET button of the de-‐ vice when starting it until the LED light turns off, and Metal will start to look for Netinstall servers. Mounting With the clip pointed forward, slide the mounting bracket into the rail on the bottom of the case, until the clip clicks into place. The SXT comes bundled with a hose clamp -‐ guide the clamp through the opening in the bracket and around the pole where it will be mounted. Tighten the hose clamp screw when alignment is complete. Two screw holes are provided as additional security against accidental bracket movement. The SXT device has a sliding door, behind which the Ethernet port, and the reset jumpers are located. This door can be also secured shut with a screw in the provided screw hole. See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 16-Oct-2012 Buttons and Jumpers • • RouterOS reset jumper hole (access through the plastic door) – resets RouterOS software to defaults. Must short cir-‐ cuit the metallic sides of the hole (with a screwdriver, for example) and boot the device. Hold screwdriver in place until RouterOS configuration is cleared. RouterBOOT reset button (access through the plastic door) has two functions: ü Hold this button during boot time until LED light starts flashing, release the button to reset RouterOS configuration (same result as with reset hole) ü Hold this button during boot time longer, until LED turns off, and then release it to make the device look for Netinstall servers. Operating System Support Currently tested operating system is MikroTik RouterOS (starting from version v5.20). Copyright and Warranty Information Copyright and Trademarks. Copyright MikroTikls SIA. This manual contains information protected by copyright law. No part of it may be reproduced or transmitted in any form without prior written permission from the copy-‐ right holder. RouterBOARD, RouterOS, RouterBOOT and MikroTik are trademarks of MikroTikls SIA. All trademarks and registered trademarks appearing in this manual are the property of their respective holders. Hardware. MikroTikls SIA warrants all RouterBOARD series equipment for the term of fifteen (15) months from the shipping date to be free of defects in materials and workmanship under normal use and service, except in case of damage caused by mechanical, electrical or other accidental or intended damages caused by improper use or due to wind, rain, fire or other acts of nature. If you have purchased your product from a MikroTik Reseller, please contact the Reseller company regarding all warranty and repair issues, the following instructions apply ONLY if you purchased your equipment directly from MikroTik Latvia To return failed unit or units to MikroTikls you must perform the following RMA (Return Material Authorization) procedure. Follow the instructions below to save time, efforts, avoid costs, and improve the speed of the RMA process. Take into account that all goods have one year warranty. Instructions are located on our webpage here: http://rma.mikrotik.com Manual. This manual is provided “as is” without a warranty of any kind, expressed or implied, including, but not limited to, the implied warranty of merchantability and fitness for a particular purpose. The manufacturer has made every effort to ensure the accuracy of the contents of this manual; however, it is possible that it may con-‐ tain technical inaccuracies, typographical or other errors. No liability is assumed for any inaccuracy found in this publication, nor for direct or indirect, incidental, consequential or other damages that may result from such an inaccuracy, including, but not limited to, loss of data or profits. Please report any inaccuracies found to sup-‐ port@mikrotik.com See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 16-Oct-2012 Federal Communication Commission Interference Statement (FCC ID: TV7SXT-2ND) This equipment has been tested and found to comply with the limits for a Class B digital device, pur-‐ suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accord-‐ ance with the instructions, may cause harmful interference to radio communications. However, there is no guar-‐ antee that interference will not occur in a particular installation. If this equipment does cause harmful interfer-‐ ence to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • • • • Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna must not be co-‐located or operation in conjunction with any other antenna or trans-‐ mitter. IMPORTANT: Exposure to Radio Frequency Radiation. 13 cm minimum distance has to be maintained between the antenna and the occupational user and 28 cm to general public. Under such configuration, the FCC radiation exposure limits set forth for an popula-‐ tion/uncontrolled environment can be satisfied. Antenna Installation. WARNING: It is installer's responsibility to ensure that when using the authorized antennas in the United States (or where FCC rules apply); only those antennas certified with the product are used. The use of any antenna other than those certified with the product is expressly forbidden in accordance to FCC rules CFR47 part 15.204. The installer should configure the output power level of antennas, according to country regulations and per antenna type. Professional installation is required of equipment with connectors to ensure compliance with health and safety issues. CE Declaration of Conformity Hereby MikroTik declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The Declaration of Conformity may be obtained by contacting sales@mikrotik.com. See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 16-Oct-2012
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf Linearized : No Page Count : 3 PDF Version : 1.4 Title : Microsoft Word - SXTr2-2nD-qg.docx Author : Normunds Rustanovics Producer : Mac OS X 10.8.2 Quartz PDFContext Creator : Word Create Date : 2012:10:16 08:12:56Z Modify Date : 2012:10:16 08:12:56ZEXIF Metadata provided by EXIF.tools