Mikrotikls SIA SXT-5HPND 2X2 MIMO 802.11 DIGITAL TRANSMISSION SYSTEM ROUTER User Manual

Mikrotikls SIA 2X2 MIMO 802.11 DIGITAL TRANSMISSION SYSTEM ROUTER USERS MANUAL

a href="https://usermanual.wiki/Mikrotikls-SIA" itemprop="url"> Mikrotikls SIA >

USERS MANUAL

See www.routerboard.com for more information. Contact support@mikrotik.com for support questions.  5-SEP-2011 RouterBOARD SXT 5HPnD Quick Setup Guide and Warranty Information The RouterBOARD SXT 5HPnD comes as a complete set, and includes a built in 802.11n dual chain wireless device, and a dual polarization 16dBi antenna. It has one BASE-T 10/100 ethernet connector which supports MDI-X auto detection. First use 1. Connect an Ethernet cable to the port behind the small plastic door 2. The SXT accepts 24V Passive PoE from the supplied PoE injector 3. The default IP address from LAN is 192.168.88.1 for configuration 4. Username is admin and there is no password Powering The board accepts powering from the Ethernet port (Passive PoE) 8-30V DC. Package contains a 24V adapter.  Booting process RouterOS is the operating system of all RouterBOARD routers. Please see detailed configuration guide here:  http://wiki.mikrotik.com/wiki/Category:Manual#list This device doesn't come fitted with a Serial Port connector, so initial connection has to be done via the Ethernet cable, using the MikroTik Winbox utility. Winbox should be used to connect to the default IP address of 192.168.88.1 with the username admin and no password.  In case IP connection is not available, Winbox can also be used to connect to the MAC address of the device. More information here: http://wiki.mikrotik.com/wiki/First_time_startup In case you wish to boot the device from network, for example to use MikroTik Netinstall, hold the RESET button of the device when start-ing it until the LED LD600 light turns off (behind the small door), and SXT will start to look for Netinstall servers. Mounting With the clip pointed forward, slide the mounting bracket into the rail on the bottom of the case, until the clip clicks into place. The SXT comes bundled with a hose clamp - guide the clamp through the opening in the bracket and around the pole where it will be mounted. Tighten the hose clamp screw when alignment is complete. Two screw holes are provided as additional security against accidental bracket movement. The SXT device has a sliding door, behind which the Ethernet port, and the reset jumpers are located. This door can be also secured shut with a screw in the provided screw hole. Buttons and Jumpers  RouterOS reset jumper hole (access through the plastic door) – resets RouterOS software to defaults. Must short cir-cuit the metallic sides of the hole (with a screwdriver, for example) and boot the device. Hold screwdriver in place until RouterOS configuration is cleared.    RouterBOOT reset button (access through the plastic door) has two functions:  Hold this button during boot time until LED light starts flashing,  release the button to reset RouterOS configuration (same result as with reset hole)  Hold this button during boot time longer, until LED turns off,  and then release it to make the device look for Netinstall servers.
See www.routerboard.com for more information. Contact support@mikrotik.com for support questions.  5-SEP-2011 Operating System Support Currently tested operating system is MikroTik RouterOS (starting from version v5). Copyright and Warranty Information Copyright and Trademarks. Copyright MikroTikls SIA. This manual contains information protected by copyright law. No part of it may be reproduced or transmitted in any form without prior written permission from the copyright holder. RouterBOARD, RouterOS, RouterBOOT and MikroTik are trademarks of MikroTikls SIA. All trademarks and registered trademarks appearing in this manual are the property of their respective holders. Hardware. MikroTikls SIA warrants all RouterBOARD series equipment for the term of fifteen (15) months from the shipping date to be free of defects in materials and workmanship under normal use and service, except in case of damage caused by mechanical, electrical or other accidental or intended damages caused by improper use or due to wind, rain, fire or other acts of nature. If you have purchased your product from a MikroTik Reseller, please contact the Reseller company regarding all warranty and repair issues, the following instructions apply ONLY if you purchased your equipment directly from MikroTik Latvia To return failed unit or units to MikroTikls you must perform the following RMA (Return Material Authorization) procedure. Follow the instructions below to save time, efforts, avoid costs, and improve the speed of the RMA process. Take into account that all goods have one year warranty. Instructions are located on our webpage here: http://rma.mikrotik.com Manual. This manual is provided “as is” without a warranty of any kind, expressed or implied, including, but not limited to, the implied warranty of merchantability and fitness for a particular purpose. The manufacturer has made every effort to ensure the accuracy of the contents of this manual; however, it is possible that it may contain technical inaccuracies, typographical or other errors. No liability is as-sumed for any inaccuracy found in this publication, nor for direct or indirect, incidental, consequential or other damages that may result from such an inaccuracy, including, but not limited to, loss of data or profits. Please report any inaccuracies found to sup-port@mikrotik.com
Download:
Mirror Download [FCC.gov]
Document ID1577232
Application IDbmsEVuoQ4zzRTJyVRzsqOQ==
Document DescriptionUSERS MANUAL
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize33.11kB (413905 bits)
Date Submitted2011-11-08 00:00:00
Date Available2011-11-08 00:00:00
Creation Date2011-11-01 15:20:21
Producing SoftwareMicrosoft® Word 2010
Document Lastmod2011-11-01 15:20:21
Document TitleUSERS MANUAL
Document CreatorMicrosoft® Word 2010
Document Author: Normis
FCC ID Filing: TV7SXT-5HPND

Navigation menu