Mikrotikls SIA SXT-5HPND 2X2 MIMO 802.11 DIGITAL TRANSMISSION SYSTEM ROUTER User Manual USERS MANUAL

Download:
Mirror Download [FCC.gov]
Document ID	1577232
Application ID	bmsEVuoQ4zzRTJyVRzsqOQ==
Document Description	USERS MANUAL
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	33.11kB (413905 bits)
Date Submitted	2011-11-08 00:00:00
Date Available	2011-11-08 00:00:00
Creation Date	2011-11-01 15:20:21
Producing Software	Microsoft® Word 2010
Document Lastmod	2011-11-01 15:20:21
Document Title	USERS MANUAL
Document Creator	Microsoft® Word 2010
Document Author:	Normis

RouterBOARD SXT 5HPnD
Quick Setup Guide and Warranty Information
The RouterBOARD SXT 5HPnD comes as a complete set, and includes a built in
802.11n dual chain wireless device, and a dual polarization 16dBi antenna. It has one
BASE-T 10/100 ethernet connector which supports MDI-X auto detection.
First use
1.
2.
3.
4.
Connect an Ethernet cable to the port behind the small plastic door
The SXT accepts 24V Passive PoE from the supplied PoE injector
The default IP address from LAN is 192.168.88.1 for configuration
Username is admin and there is no password
Powering
The board accepts powering from the Ethernet port (Passive PoE) 8-30V DC. Package
contains a 24V adapter.
Booting process
RouterOS is the operating system of all RouterBOARD routers. Please see detailed configuration guide here:
http://wiki.mikrotik.com/wiki/Category:Manual#list
This device doesn't come fitted with a Serial Port connector, so initial connection has to be done via the Ethernet cable, using the MikroTik
Winbox utility. Winbox should be used to connect to the default IP address of 192.168.88.1 with the username admin and no password.
In case IP connection is not available, Winbox can also be used to connect to the MAC address of the device. More information here:
http://wiki.mikrotik.com/wiki/First_time_startup
In case you wish to boot the device from network, for example to use MikroTik Netinstall, hold the RESET button of the device when starting it until the LED LD600 light turns off (behind the small door), and SXT will start to look for Netinstall servers.
Mounting
With the clip pointed forward, slide the mounting bracket into the rail on the bottom of the case, until the clip clicks into place. The SXT
comes bundled with a hose clamp - guide the clamp through the opening in the bracket and around the pole where it will be mounted.
Tighten the hose clamp screw when alignment is complete. Two screw holes are provided as additional security against accidental bracket
movement.
The SXT device has a sliding door, behind which the Ethernet port, and the reset jumpers are located. This door can be also secured shut
with a screw in the provided screw hole.
Buttons and Jumpers


RouterOS reset jumper hole (access through the plastic door) – resets RouterOS software to defaults. Must short circuit the metallic sides of the hole (with a screwdriver, for example) and boot the device. Hold screwdriver in place
until RouterOS configuration is cleared.
RouterBOOT reset button (access through the plastic door) has two functions:
 Hold this button during boot time until LED light starts flashing,
release the button to reset RouterOS configuration (same result as with reset hole)
 Hold this button during boot time longer, until LED turns off,
and then release it to make the device look for Netinstall servers.
See www.routerboard.com for more information. Contact support@mikrotik.com for support questions.
5-SEP-2011
Operating System Support
Currently tested operating system is MikroTik RouterOS (starting from version v5).
Copyright and Warranty Information
Copyright and Trademarks. Copyright MikroTikls SIA. This manual contains information protected by copyright law. No part of it may be
reproduced or transmitted in any form without prior written permission from the copyright holder. RouterBOARD, RouterOS, RouterBOOT
and MikroTik are trademarks of MikroTikls SIA. All trademarks and registered trademarks appearing in this manual are the property of their
respective holders.
Hardware. MikroTikls SIA warrants all RouterBOARD series equipment for the term of fifteen (15) months from the shipping date to be free
of defects in materials and workmanship under normal use and service, except in case of damage caused by mechanical, electrical or other
accidental or intended damages caused by improper use or due to wind, rain, fire or other acts of nature.
If you have purchased your product from a MikroTik Reseller, please contact the Reseller company regarding all warranty and repair issues,
the following instructions apply ONLY if you purchased your equipment directly from MikroTik Latvia
To return failed unit or units to MikroTikls you must perform the following RMA (Return Material Authorization) procedure. Follow the
instructions below to save time, efforts, avoid costs, and improve the speed of the RMA process. Take into account that all goods have one
year warranty.
Instructions are located on our webpage here: http://rma.mikrotik.com
Manual. This manual is provided “as is” without a warranty of any kind, expressed or implied, including, but not limited to, the implied
warranty of merchantability and fitness for a particular purpose. The manufacturer has made every effort to ensure the accuracy of the
contents of this manual; however, it is possible that it may contain technical inaccuracies, typographical or other errors. No liability is assumed for any inaccuracy found in this publication, nor for direct or indirect, incidental, consequential or other damages that may result
from such an inaccuracy, including, but not limited to, loss of data or profits. Please report any inaccuracies found to support@mikrotik.com
See www.routerboard.com for more information. Contact support@mikrotik.com for support questions.
5-SEP-2011
Federal Communication Commission Interference Statement
(FCC ID: TV7SXT-5HPND)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of
the following measures:




Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
This device and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter.
IMPORTANT: Exposure to Radio Frequency Radiation.
13 cm minimum distance has to be maintained between the antenna and the occupational user and 28 cm to general public.
Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be
satisfied.
Antenna Installation. WARNING: It is installer's responsibility to ensure that when using the authorized antennas in the
United States (or where FCC rules apply); only those antennas certified with the product are used. The use of any antenna
other than those certified with the product is expressly forbidden in accordance to FCC rules CFR47 part 15.204. The installer
should configure the output power level of antennas, according to country regulations and per antenna type. Professional
installation is required of equipment with connectors to ensure compliance with health and safety issues.
See www.routerboard.com for more information. Contact support@mikrotik.com for support questions.
5-SEP-2011

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 3
Language                        : en-US
Tagged PDF                      : Yes
Author                          : Normis
Creator                         : Microsoft® Word 2010
Create Date                     : 2011:11:01 15:20:21+02:00
Modify Date                     : 2011:11:01 15:20:21+02:00
Producer                        : Microsoft® Word 2010

EXIF Metadata provided by EXIF.tools