MilDef Crete DR886EX Tablet computer User Manual DR886 User Guide 080901
MilDef Crete Inc. Tablet computer DR886 User Guide 080901
Users Manual
TABLET COMPUTER DR886EX USER’S GUIDE Copyright © 2008 CReTE Systems Inc. All rights reserved. No part of this publication may be processed; such as reproduced, transmitted, transcribed, stored in a retrieval system, translated into any computer language in any form, or by any means of electronic, mechanical, magnetic, optical, chemical, or others without the prior written permission of the manufacturer. The manufacturer reserves the right to revise this publication and to make changes to the contents here of without obligation to notify any person of such revision or changes. The manufacturer makes no representations or warranties, either expressed or implied, about the contents and specifically disclaims any warranties as to merchantability or fitness for any particular purpose. Any of the software described in this manual is sold or licensed "as is". Should the programs prove defective following purchase, the buyer (and not the manufacturer, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair and any incidental or consequential damages resulting from any software defects. Trademark Acknowledgments Windows is registered trademarks of Microsoft Corp. Intel® Core™2 Duo processor is the registered trademark of Intel Corp. All product and company names are trademarks or registered trademarks of their respective holders. EMC and Safety Notice FCC Regulations: This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Re-orient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation. RF Exposure Information (SAR) This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. Tests for SAR are conducted using standard operating positions accepted by the FCC with the EUT transmitting at the specified power level in different channels. The highest SAR value for the device as reported to the FCC is 0.789 W/kg when placed next to the body. The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of http://www.fcc.gov/oet/fccid after searching on FCC ID: IR5DR886EX. Regulatory Information/Disclaimers Installation and use of this computer must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, or the substitution of the connecting cables and equipment other than manufacturer specified. It is the responsibility of the user to correct any interference caused by such unauthorized modification, substitution or attachment. Manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failing to comply with these guidelines. Important Note FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operated with any other antenna or transmitter. CE Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms: EN55022 (CISPR 22) Radio Frequency Interference EN55024 (EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6, EN61000-4-8, EN61000-4-11, EN61000-3-2, EN61000-3-3) Generic Immunity Standard EN60950 (IEC950) Product Safety R&TTE (CE) Manual Regulatory Requirement (WLAN - IEEE 802.11b/g) 802.11b/g Restrictions: European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range 2.400-2.4835 GHz. In France, the equipment must be restricted to the 2.4465-2.4835 GHz frequency range and must be restricted to indoor use. CE Declaration of Conformity Is herewith confirmed to comply with the requirements set out in the Council Directive on the approximation of the laws of the member states relating to Electromagnetic Compatibility (89/336/EEC), Low-voltage Directive (73/23/EEC) and the Amendment Directive (93/68/EEC), the procedures given in European Council Directive 99/5/EC and 89/3360EEC. The equipment was passed. The test was performed according to the following European standards. EN 300 328 V.1.4.1 (2003-04) EN 301 489-1 V.1.4.1 (2002-04)/EN 301 489-17 V.1.2.1 (2002-04) EN 50371:2002 EN 60950:2000 UL, TÜV AC Adapter (TÜV includes EN60950 LVD) Power Conservation This computer consumes much less power than conventional computers. However, power consumption may be reduced by properly configuring the Power Management Setup. It is recommended the power saving functions be enabled even when not running on battery power. Please read the power saving features and the setting procedures described in this manual for setting your computer. Environmental Information, Material Safety and Recycling Caution: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. All materials used in the construction of this equipment are recyclable or environmentally friendly. Please recycle the packing materials, and at the end of the product's life, all other materials by local regulations. Please refer “Material and Recycling” for the contents of the materials. - The equipment may still contain tiny amount of hazardous substances for health and environment, though those are below control level. - To avoid spreading such substances into the eco system, and to minimize the pressure on the natural, you are encouraged to use the appropriate take-back. Those will reuse or recycle most of the materials in a sound way after end life. - The crossed bin symbol indicates proper disposal is required. - For more information on collection, reuse and recycling, please consult local or regional waste administration. You can also contact the dealer for more information on the environmental details of the equipment. CONTENTS GETTING STARTED ............................................................................................ 1 UNPACKING .................................................................................................................................. 1 QUICK CHECK ............................................................................................................................... 2 CONTROLS AND INDICATORS ........................................................................................................ 3 COMPONENTS AND OPERATIONS .................................................................. 7 LOCATION ..................................................................................................................................... 7 RUGGEDNESS ................................................................................................................................ 7 OPERATING SYSTEMS.................................................................................................................... 7 AC ADAPTER ................................................................................................................................ 8 BATTERY ...................................................................................................................................... 8 BOOT UP AND POST................................................................................................................... 10 TIMEOUT/STANDBY/WAKE UP .................................................................................................... 10 SHUTDOWN ................................................................................................................................. 11 RTC............................................................................................................................................ 11 SAFE GUARD THE COMPUTER ..................................................................................................... 11 REPLACING MODULES ................................................................................................................ 12 HARD DISK DRIVE ...................................................................................................................... 12 TOUCH SCREEN ........................................................................................................................... 13 PCMCIA CARD .......................................................................................................................... 13 EXPRESS CARD ........................................................................................................................... 13 EXTERNAL BACKLIGHT KEYBOARD (OPTIONAL)......................................................................... 13 DOCKLIGHT (OPTIONAL) ............................................................................................................. 14 STAND UNIT (OPTIONAL) ............................................................................................................ 16 HEATER ...................................................................................................................................... 16 RF DEVICE .................................................................................................................................. 16 OPTIONAL DEVICES......................................................................................... 18 MEMORY CARD .......................................................................................................................... 18 2ND BATTERY ............................................................................................................................... 18 WIRELESS LAN CARD ................................................................................................................ 18 MDC MODEM CARD ................................................................................................................... 18 VEHICLE ADAPTER ..................................................................................................................... 18 DUAL BATTERY CHARGER .......................................................................................................... 18 DOCKLIGHT ................................................................................................................................ 18 STAND UNIT................................................................................................................................ 19 RF DEVICE .................................................................................................................................. 19 SPECIFICATIONS............................................................................................... 20 CPU............................................................................................................................................ 20 MEMORY..................................................................................................................................... 20 DISPLAY...................................................................................................................................... 20 LCD............................................................................................................................................ 20 HARD DISK DRIVE ...................................................................................................................... 20 TOUCH SCREEN ........................................................................................................................... 20 I/O PORTS ................................................................................................................................... 21 DIMENSIONS AND WEIGHT .......................................................................................................... 21 AC ADAPTER .............................................................................................................................. 21 BATTERY .................................................................................................................................... 21 KEYPAD/KEYBOARD ................................................................................................................... 22 VEHICLE ADAPTER (OPTIONAL) .................................................................................................. 22 DOCKLIGHT DL-8I/DL-8M (OPTIONAL) ..................................................................................... 22 STAND UNIT (OPTIONAL) ............................................................................................................ 22 MATERIALS AND RECYCLING ...................................................................................................... 23 ENVIRONMENTAL........................................................................................................................ 23 BIOS SETUP ........................................................................................................ 24 MAIN MENU................................................................................................................................ 24 IDE CHANNEL 0 MASTER SUB-MENU......................................................................................... 25 IDE CHANNEL 0 SLAVE SUB-MENU ........................................................................................... 26 IDE CHANNEL 1 MASTER SUB-MENU......................................................................................... 27 IDE CHANNEL 1 SLAVE SUB-MENU ........................................................................................... 28 ADVANCED MENU ...................................................................................................................... 30 SIO SMC227 CONFIGURATION SUB-MENU ................................................................................ 32 SECURITY MENU ......................................................................................................................... 34 RF SECURITY CONTROL SUB-MENU ........................................................................................... 36 TPM STATE MENU ..................................................................................................................... 37 BOOT MENU................................................................................................................................ 38 EXIT MENU ................................................................................................................................. 39 UTILITIES AND DRIVERS ................................................................................ 40 CHIPSET ...................................................................................................................................... 40 VGA UTILITY ............................................................................................................................. 40 AUDIO DRIVER............................................................................................................................ 41 USB 2.0 ...................................................................................................................................... 41 TOUCH SCREEN DRIVER.............................................................................................................. 41 PCMCIA DRIVER ....................................................................................................................... 42 MINI PCI 1G AX92200 LAN ..................................................................................................... 42 MINI PCI INT8100 LAN ............................................................................................................ 42 MINI PCI-E 1G RTL8111B LAN ............................................................................................... 42 MINI PCI-E INTEL 3945ABG WLAN......................................................................................... 42 FAX/MODEM CARD DRIVER........................................................................................................ 42 WIRELESS MANAGER .................................................................................................................. 43 INPUT MANAGEMENT SERVICES ................................................................................................. 43 MAINTENANCE/SERVICE................................................................................ 51 CLEANING ................................................................................................................................... 51 TROUBLESHOOTING .................................................................................................................... 51 RMA SERVICE ............................................................................................................................ 51 Getting Started GETTING STARTED Unpacking The following components come with your computer. If anything is missing or damaged, please notify the dealer immediately. - Computer unit - AC Adapter - AC Power Cord - Utility CD - User's Guide - Carrying Bag Getting Started Quick Check - Insert the battery into compartment; fix the screw till battery is in position. - Attach the AC adapter and charge battery for at least 10 minutes. Turn ON the computer by pressing the power button momentarily. Notice: - When ambient temperature is under 0℃, the system may not boot up immediately. System will beep with charge light flashing while heater working. After 13~15 minutes, the system will boot up automatically - Under emergency situation, to skip heating and boot up system immediately by pressing power button for >10 seconds. (But can not guarantee all devices on the computer work properly) - Turn OFF the computer using either one of the following procedures: 1. Press power button momentarily to “Standby”* or “Hibernate”* dependent on operating system (OS) and power scheme settings. 2. Press power button for 4 seconds to have a “Hard” power off. System shuts down without saving any data or parameters. *: Some operating systems may not support these functions. 3. Click Start → Shut Down in Windows to Turn OFF. Driver or application software installation may be necessary for further operation. Getting Started Controls and Indicators Note: Some of the functions are optional. Top F1~F6: Fn: RF device indicator Function keys, blue font are alternative functions enabled by pressing Fn and the key simultaneously To enable alternative function keys Sleep button (refer “Timeout/Standby/Wake up”) Display brightness decrease Display brightness increase Power button (refer “Timeout/Standby/Wake up”) Getting Started Battery charge/heater activity indicator ON: Charging OFF: Battery full (when no battery installed it’s off, too) Flash: Heater active (heater is an optional device) HDD (Hard Disk Drive) activity indicator Power indicator Rear 1. Secondary battery connector Getting Started Left 1. 2. 3. 4. Battery LAN USB (Universal Serial Bus) PCMCIA slots or Express Card Right 1. DC jack (2 pin for DR886EX-I, 3 pin for DR886EX-M) 2. Serial port (COM1) Getting Started Top 1. HDD 2. Kensington lock slot Bottom 1. 2. Docking connector External antenna jack (optional) Components and Operations COMPONENTS AND OPERATIONS Location A clean and moisture-free environment is preferred. Make room for air circulation. Avoid areas with: - Sudden or extreme changes in temperature. - Extreme heat. - Strong electromagnetic fields (near television set, motor rotation area, etc.). - Dust or high humidity. If it is necessary to work in a hostile environment, please regularly maintain your computer by cleaning dust, water, etc. and keep it in optimal condition. Ruggedness The computer is designed with rugged features such as vibration, shock, dust, and rain/water protection. However, it is still necessary to provide appropriate protection while operating in harsh environments. NEVER immerse the computer in water. Doing so may cause permanent damages. Drop may cause parts break or permanent damages. The D-sub connector cap is for dust and shock protection only. The connector itself is sealed internally. Other I/O ports and devices must have caps tightly closed or cable inlets sealed while exposed to water or dust. All connectors will corrode if exposed to water or moisture. Corrosion is accelerated if the power is ON. Please take proper measures in cable connection to avoid water entering into connectors. The DC jack and cables are sealed and may be operated with water splashing while attached. All port covers should be in place when no cable is attached. Operating Systems The computer is compatible with most operating systems (OS). However, not all functions are 100% compatible. For example, ACPI, APM, Smart Battery, etc. are not available on DOS, Windows NT, and other non-Microsoft OS. Consequently “Standby”, “Hibernation”, “Battery Gauge” etc. would not work under such operating systems. ACPI: Advanced Configurations and Power Interface APM: Advanced Power Management Components and Operations AC Adapter The AC adapter performs two functions: - It powers the computer from an external AC source. - It charges the computer battery. The adapter automatically detects the AC line voltage (110V or 220V) and adjusts accordingly. The following are recommended when using the AC adapter: - Use a properly grounded AC outlet. - Use one AC outlet exclusively for the computer. Having other appliances on the same line may cause interference. - Use a power strip with built-in surge protection. Connect the AC adapter: - Plug the AC cord to the adapter. - Plug the other end of the AC cord into the wall outlet. Make sure the green LED on the adapter turns on. - Attach the DC plug into the power jack of the computer; turn the lock ring clockwise to secure it. AC Adapter Indicator The green LED indicates that AC power is ready. Battery The computer will automatically switch to battery when the external power source (AC adapter or optional vehicle adapter) is disconnected. Battery Power Saving Tips The computer comes with an intelligent power-saving feature. You may extend the battery life by: - Setup power saving functions in Operating System Power Management options (e.g. Windows Power Options). - Setup power saving functions in BIOS “Power Management Setup” (mainly for non-ACPI/APM operating systems). - Lower the intensity of the display by brightness control. - Turn the computer into standby (by Sleep or Power button) when it is temporarily not in use. Components and Operations Shut down the computer when it will not be in use for longer period of time. Battery Low When the battery is nearly exhausted, the computer gives the following “Battery Low” warnings: - Windows battery low warning. - The power LED flashes. Once the “Battery Low” warning occurs, please: - Save and close the files you are currently working on then shut down the computer. - Plug in AC or vehicle adapter to recharge the battery. Battery Gauge You may check battery status from battery gauge in Windows. Click the power/battery icon to reveal the battery gauge window. Note: Battery characteristic varies depending on factors such as ambient temperature, charging method, load current, aging, etc. For example, the chemicals of the battery are more inactive at low temperature, thus decreases the output power. The battery gauge should only be used as a reference. Please do not expect it to show the exact amount of the power remaining. There is no memory effect on Lithium Ion battery cells. However, discharge the battery to nearly empty every month will help calibrating the internal gauge Components and Operations Charging the Battery Plug in the AC adapter or vehicle adapter to start the battery charging. If the battery is already full, the sense circuitry will stop high current charge within several minutes. The LED Indicator turns ON when the battery is charging and turns OFF when the battery charge is completed. To charge the Secondary Battery, simply install it into the computer and attach the AC adapter. The internal charger will charge the Primary and Secondary batteries simultaneously. Optional Dual Battery Charger can charge Primary and Secondary batteries externally. Boot Up and POST The computer turns ON and loads the operating system (such as Windows) into the system memory. This start-up procedure is called “boot up”. The ROM BIOS Power On Self-Test (POST) Each time the computer powers on, it automatically performs a self-test of its memory and hardware devices. Timeout/Standby/Wake up In Windows Control Panel Power Options you may set preferred options. If timeouts are set, the sequences of function are as follows: - Normal → Timeout (Monitor, HDD) → Touch screen or any key → Wake up (Normal) - Normal → Timeout (Standby, Hibernate) → Power button → Wake up (Normal) Directly press sleep button or power button the functions are as follows: • Normal → Sleep button → Standby (also locks all function keys & touch screen) → Power button → Wake up (Normal) • Normal → Power button → Standby/Hibernate/Shut down/etc. (dependents on power button setting) Note: Timeout/Standby works under both AC adapter and battery mode. Some functions may not work under Windows NT or other non-Windows operating systems. 10 Components and Operations Shutdown The following procedure is recommended in shutting down the computer: 1. Save any work you want to keep. 2. Make sure none of the disk drives are active (HDD and CD-ROM drive). 3. Remove any diskettes, CD-ROMs, or other media. 4. Follow the shut down procedure of your Operating System. Failure to shut down the computer properly may result in loss of data or hardware damages. Automatic shut down is activated at battery exhaust. Be sure to finish your work and save all your data when the battery low warning appears. RTC Battery backed up RTC (Real Time Clock/Calendar) is built in an on-board CMOS (Complementary Metal Oxide Semiconductor) chip. The RTC keeps track of the time and date while the computer is off. The CMOS chip also stores system setup information. RTC battery is also recharged when AC adapter is attached. Tips: When computer is not used for longer period, recharge it at least once per month to ensure RTC operation. Safe Guard the Computer Plug the Kensington lock into the slot near HDD and turn lock it. Both the computer and HDD are secured. Kensington lock is a widely available 3rd party product. 11 Components and Operations Replacing Modules Caution! Turn OFF the power before replacing any module. To remove the modules: 1. Turn OFF the computer. (“Hibernate” or “suspend to disk” are not recommended as the parameters may change when modules are changed.) 2. Disconnect all cables from the computer. 3. Use a coin to turn loose the screws on the modules. 4. Remove the battery from the compartment. 5. Remove the HDD from the computer. To re-install the modules: Gently push the module into the slot. Fasten the screw to fix the module. Make sure the o-rings are firmly fixed. No sealant is necessary for the o-rings. Hard Disk Drive The Hard Disk Drive (HDD) is a 2.5” type standard serial ATA interface data storage device. HDD is user removable. This provides convenience and security. It can ONLY be removed while power is OFF. 12 Components and Operations Note: NEVER drops your HDD module or exposes it to high temperature, high humidity, or any hazardous environment. NEVER try to disassemble the module. Static discharge may destroy your device and data. Always pick up the modules by touching the case only. Touch Screen Touch screen facilitates direct finger touch or pen input on the screen instead of mouse or touch pad. PCMCIA Card The computer supports 1x type-II PCMCIA card. To remove the card, push the eject button. The eject button can hide into the compartment by pushing it inward gently. Express Card The computer supports two form Express cards, 34 mm wide & 54 mm wide in an L-shape. You can install an Express Card while the computer is running. The computer automatically detects the card. To install an Express Card: - Hold the card with the top side of the card. - Slide the card into the slot until the card is completely seated in its connector. To remove an Express Card: Press the card and remove the card gently. External Backlight Keyboard (optional) The external backlight keyboard is equivalent to a full size desktop keyboard plus extra functions. The interface is via USB port. Track point The track point is functionally equivalent to a mouse. Pushing the track point may move the cursor on the screen. The 2 buttons act same as mouse buttons. Backlight Press [I-O] key for approximately 1 second turns keyboard backlight ON or OFF. 13 Components and Operations Docklight (optional) Docklight acts as docking unit or port enhancer. It contains more ports that are not available on system unit. Mount Docklight 1. Open the rubber cap on the docking connector. 2. Align the docking connector. 3. Attach Docklight. 4. Fix the screws. 14 Components and Operations Docklight ports Top 1. Docking connector Bottom and Left: 1. 2. 3. 4. 5. 6. 7. 8. 9. Audio jacks (Microphone/Speaker) RGB port Modem jack (RJ11) LAN jack Serial port (COM3) USB port 1, 2 (standard type) USB port 3, 4 (proprietary sealed type) Serial port (COM2) DC jack 15 Components and Operations Stand Unit (optional) Stand unit can hold the system unit and Docklight with adjustable view angle. It can be used in office or in vehicle. There are 2 configuration options: - Stand unit only to accept system unit. - Stand unit with Docklight hooked to accept system unit. Mount Stand Unit 1. Open the rubber cap on the docking connector. 2. Align the computer into stand unit. 3. Push the lever to engage and fix. 4. Lock the computer. Heater Built-in heater and control circuit activates heating when computer is turned ON at temperature 0°C~-20°C (32°F~-4°F). The heating is automatically; just turn ON power the heater controller will detect temperature and take over. The power indicator flashes while heating. The computer would boot up when the internal temperature reaches safe level. It may take 5~20 minutes depends on how cold the temperature is. For temperature below –20°C (-4°F) the computer may never heat up. Plug in AC or vehicle adapter for heating as battery power may become very low at low temperature. RF Device When RF device connect/function as one of (GPS/Wi-Fi) stared up, the RF led will be on, and then have to match up the "wireless manager" application software to control the device "on/off". 16 Components and Operations Please refer the illustration as below: 17 Optional Devices OPTIONAL DEVICES Memory Card The memory card will expand main memory to facilitate better system performance. The cards are available as following: 512MB, 1GB, 2GB 2nd Battery A Lithium Ion rechargeable 2nd battery may mount on the rear. It has 1.5 times capacity of primary battery and same Smart Battery compliance. The computer’s internal charger can detect 2nd battery and perform charging accordingly. Wireless LAN Card IEEE 802.11a,b,g wireless LAN card and rugged antenna. MDC Modem Card V.90 56K Fax/Modem Vehicle Adapter Converting power from car lighters (12~14V) or truck batteries (24~28V). It can power the system and charge the batteries simultaneously. Caution: Remove or disconnect the vehicle adapter when leaving the vehicle to avoid battery exhaustion. Dual Battery Charger The charger provides two slots for the Primary and Secondary battery respectively. It allows charging of both batteries simultaneously and accepts power from AC adapter or Vehicle adapter. It takes approximately 3~4 hours to fully charge both batteries. Docklight Ports: Serial x 2, USB x 4, LAN, Modem, RGB, Microphone, and DC jack. The Docklight can attach to computer or stand unit for mobile or stationary operation. 18 Optional Devices Stand Unit This acts as computer holder for office or vehicle operation and can work with or without Docklight. RF Device The RF device are available as following: - GPS - Wi-Fi 19 Specifications SPECIFICATIONS CPU Intel Core2 Duo ULV U7500 1.06GHz - Processor Memory System memory Expandable Cache memory Video memory Standard: 512MB 2GB Internal level-II 2MB 224MB (shared RAM) Display The display is a SVGA compatible LCD (Liquid Crystal Display) of 800 x 600 dots (horizontal x vertical) or XGA 1024 x 786. The computer is also capable of displaying super XGA 1280 x 1024 dots on the LCD or external monitor. LCD Type: Resolution: Mode: Color: Characters x Row: 8.4” Active TFT Color 800 x 600 or 1024 x 768 pixels VGA, EGA, MGA, SVGA, XGA 16.8 million true colors on 800 x 600 mode 80 x 25 Hard Disk Drive Type: Interface: 2.5” SATA Touch Screen Type: Interface: Resolution: Resistive, polarized Serial (COM4) >1024x1024 20 Specifications I/O Ports Serial port (DB9) LAN jack 1 type-II PCMCIA slots + 1 Express slot or 2 type II PCMCIA slots Docking port USB port DC jack Dimensions and Weight Width: 250mm (9.8”) Depth: 190mm (7.4”) Height: 42mm (1.65”) Weight: 1.9Kg (4.2 lb) Note: Weight varies depending on system configurations. AC Adapter Input Voltage: Frequency: Output Voltage: Maximum Power: Dimension: Weight: AC 100 - 240 V 50/60 Hz DC 19V 90 Watts 133 mm (W) x 58mm (D) x 30mm (H) 400 g (0.88 lb.) Battery Primary Battery: Type: Capacity: Dimension: Weight: 6 x 18650 cells Lithium Ion 11.1V 4400mAH 150 mm (W) x 58 mm (D) x 20 mm (H) 300 g (0.65 1b.) 2nd Battery (optional): Type: 9 x 18650 cells Lithium Ion Capacity: 11.1V 6600mAH 21 Specifications Dimension: Weight: 150 mm (W) x 90 mm (D) x 20 mm (H) 500 g (1.1 1b.) Keypad/Keyboard Embedded Keypad: Function keys: F1~F6 Optional External USB Keyboard: Number of keys: 89 Key travel: 1.5 mm Function: Emulates standard 101/102-key keyboard Trackpoint: Equivalent to PS/2 mouse Vehicle Adapter (optional) Input Voltage Input Current Output Voltage Output Current Wiring Application 12V/24V (10~32V) Auto-sense 2.5A/5.5A max. (12V/24V respectively) 19V +/-5% 2.8A Cigarette lighter/Truck battery Car or Truck installation Docklight DL-8I/DL-8M (optional) Ports: Serial x 2*, USB x 4*, LAN, Modem, RGB, Audio (microphone), DC jack Dimensions: 250mm (9.8” W) x 34mm (1.3” D) x 38mm (1.5” H) Weight: 0.45Kg (1 lb.) approximately *: Serial ports: COM1 RS232 only, COM3 RS232 or optional RS422 USB ports: 2 standard connectors & 2 proprietary environmental sealed connectors Stand Unit (optional) Dimensions: Weight: 240 mm (9.4” W) x 290mm (11.4” D) x 150mm (5.9” H) 1.6Kg (3.5 lb.) approximately 22 Specifications Materials and Recycling Materials of the computer are as follows: Cabinet: Magnesium alloy AZ91D UL grade PC+ABS GE C2800 or TN-3813BW Bracket: Aluminum 5052 Steel with Nickel plating Stainless Steel S304 PCB: FR-4, UL 94V0 Battery: Rechargeable Lithium Ion cells Packing: Carton: Unbleached paper Cushion: Recyclable PE Carrying bag: Recyclable PE Fiber User's Guide: Paper Please recycle the parts according to local regulations. Environmental Temperature: Storage: Humidity: Altitude: Operating: DR886-I: 0 ~ 40ºC (32 ~ 104ºF) DR886-M: -20 ~ 50ºC (-4~ 122ºF) DR886-I: -20 ~ 60ºC (-4 ~ 140ºF) DR886-M: -40 ~ 70ºC (-4 ~ 140ºF) Operating/Storage: 5~95% (non-condensing) Operating/Storage: 4572 /12,180 meters (15,000/ 40,000 feet) 23 BIOS Setup BIOS SETUP Press [F2] at boot up to enter BIOS setup. Use arrow keys to select options and [+/-] to modify them. When finished, move to ”Exit” and press [Enter] then confirm save by pressing [Y]. Main Menu Main • • • • Advanced Phoenix TrustedCore (tm) Setup Utility Security TPM State Boot Item Specific Help System Time: System Date: [16:19:20] [03/02/2007] Legacy Diskette A: [1.44/1.25MB 3½"] IDE Channel 0 Master IDE Channel 0 Slave IDE Channel 1 Master IDE Channel 1 Slave [None] [None] [None] [None] System Memory: Extended Memory: 640 KB 1038336 KB F1 Help Esc Exit ↑↓ Select ↔ Menu Item Exit, , or selects field. –/+ Change Values Enter Select ► Sub-Menu F9 F10 Setup Defaults Save and Exit Note: The contents may vary depending on computer configurations. Main Menu Selections You can make the following selections on the Main Menu. Use the sub-menus for other selections. Feature System Time System Date Legacy Diskette A Options HH:MM:SS MM/DD/YYYY Disabled 360 Kb 1.2 MB 720 Kb 1.44/1.25 MB 2.88 MB Description Set the system time Hour, Minute, Second. Set the system date Month, Day, Year. Select floppy type. Note that 1.25 MB 3½” references a 1024 byte/sector Japanese media format. The 1.25MB, 3½" diskette requires a 3-Mode floppy-disk drive. 5¼" 5¼" 3½" 3½" 3½" 24 BIOS Setup IDE Channel 0 Master Sub-Menu Phoenix TrustedCore (tm) Setup Utility Main IDE Channel 0 Master [None] Type: [Auto] Multi-Sector Transfers: LBA Mode Control: 32 Bit I/O: Transfer Mode: Ultra DMA Mode: [Disabled] [Disabled] [Disabled] [Standard] [Disabled] F1 Help Esc Exit ↑↓ Select ↔ Menu Item Item Specific Help User = you enter parameters of hard-disk drive installed at this connection. Auto = autotypes hard-disk drive installed here. CD-ROM = a CD-ROM drive is installed here. ATAPI Removable = removable disk drive is installed here. –/+ Change Values Enter Select ► Sub-Menu F9 F10 Setup Defaults Save and Exit IDE Channel 0 Master Sub-Menu Selections You can make the following selections on the IDE Channel 0 Master sub-menu. Feature Type 32 Bit I/O Options Description User = you enter parameters of hard-disk drive installed at this connection. Auto = autotypes hard disk drive installed here. CD-ROM = a CD-ROM drive is installed here. ATAPI Removable = removable disk drive is installed here. This setting enables or disables 32 bit IDE data transfers. Auto None ATAPI Removable CD-ROM IDE Removable Other ATAPI User Disabled Enabled 25 BIOS Setup IDE Channel 0 Slave Sub-Menu Phoenix TrustedCore (tm) Setup Utility Main IDE Channel 0 Slave [None] Type: [Auto] Multi-Sector Transfers: LBA Mode Control: 32 Bit I/O: Transfer Mode: Ultra DMA Mode: SMART Monitoring: [Disabled] [Disabled] [Disabled] [Standard] [Disabled] Disabled F1 Help Esc Exit ↑↓ Select ↔ Menu Item Item Specific Help User = you enter parameters of hard-disk drive installed at this connection. Auto = autotypes hard-disk drive installed here. CD-ROM = a CD-ROM drive is installed here. ATAPI Removable = removable disk drive is installed here. –/+ Change Values Enter Select ► Sub-Menu F9 F10 Setup Defaults Save and Exit IDE Channel 0 Slave Sub-Menu Selections You can make the following selections on the IDE Channel 0 Slave sub-menu. Feature Options Type Auto None ATAPI Removable CD-ROM IDE Removable Other ATAPI User 32 Bit I/O Disabled Enabled Description User = you enter parameters of hard-disk drive installed at this connection. Auto = autotypes hard disk drive installed here. CD-ROM = a CD-ROM drive is installed here. ATAPI Removable = removable disk drive is installed here. This setting enables or disables 32 bit IDE data transfers. 26 BIOS Setup IDE Channel 1 Master Sub-Menu Phoenix TrustedCore (tm) Setup Utility Main IDE Channel 1 Master [None] Type: [Auto] Multi-Sector Transfers: LBA Mode Control: 32 Bit I/O: Transfer Mode: Ultra DMA Mode: [Disabled] [Disabled] [Disabled] [Standard] [Disabled] F1 Help Esc Exit ↑↓ Select ↔ Menu Item Item Specific Help User = you enter parameters of hard-disk drive installed at this connection. Auto = autotypes hard-disk drive installed here. CD-ROM = a CD-ROM drive is installed here. ATAPI Removable = removable disk drive is installed here. –/+ Change Values Enter Select ► Sub-Menu F9 F10 Setup Defaults Save and Exit IDE Channel 1 Master Sub-Menu Selections You can make the following selections on the IDE Channel 1 Master sub-menu. Feature Options Type Auto None ATAPI Removable CD-ROM IDE Removable Other ATAPI User 32 Bit I/O Disabled Enabled Description User = you enter parameters of hard-disk drive installed at this connection. Auto = autotypes hard disk drive installed here. CD-ROM = a CD-ROM drive is installed here. ATAPI Removable = removable disk drive is installed here. This setting enables or disables 32 bit IDE data transfers. 27 BIOS Setup IDE Channel 1 Slave Sub-Menu Phoenix TrustedCore (tm) Setup Utility Main IDE Channel 1 Slave [None] Type: [Auto] Multi-Sector Transfers: LBA Mode Control: 32 Bit I/O: Transfer Mode: Ultra DMA Mode: SMART Monitoring: [Disabled] [Disabled] [Disabled] [Standard] [Disabled] Disabled F1 Help Esc Exit ↑↓ Select ↔ Menu Item Item Specific Help User = you enter parameters of hard-disk drive installed at this connection. Auto = autotypes hard-disk drive installed here. CD-ROM = a CD-ROM drive is installed here. ATAPI Removable = removable disk drive is installed here. –/+ Change Values Enter Select ► Sub-Menu F9 F10 Setup Defaults Save and Exit IDE Channel 1 Slave Sub-Menu Selections You can make the following selections on the IDE Channel 1 Slave sub-menu. Feature Options Type Auto None ATAPI Removable CD-ROM IDE Removable Other ATAPI User 32 Bit I/O Disabled Enabled Description User = you enter parameters of hard-disk drive installed at this connection. Auto = autotypes hard disk drive installed here. CD-ROM = a CD-ROM drive is installed here. ATAPI Removable = removable disk drive is installed here. This setting enables or disables 32 bit IDE data transfers. 28 BIOS Setup General Help Window Pressing or on any menu brings up the General Help window that describes in detail the keys and functions for setup. The scroll bar on the right of any window indicates that there is more than one page of information in the window. Use and to display all the pages. Pressing and displays the first and last page. Pressing displays each page and then exits the window. Press to exit the current window. 29 BIOS Setup Advanced Menu Phoenix TrustedCore (tm) Setup Utility Security TPM State Boot Exit Item Specific Help Legacy USB Support: [Enabled] Summary screen: [Disabled] Enable support for Legacy Boot-time Diagnostic Screen: [Enabled] Universal Serial Bus QuickBoot Mode: [Enabled] Extended Memory Testing [None] IGD - Boot Type: [VBIOS Default] PS/2 Mouse [Auto Detect] PCI Express - Root Port 1: [Enabled] USB - Device 29, Function 7: [Enabled] Passive Cooling Trip Point [79 C] • SIO SMC227 CONFGURATION Main Advanced F1 Help Esc Exit ↑↓ Select Item ↔ Menu –/+ Change Values Enter Select ► Sub-Menu F9 F10 Setup Defaults Save and Exit Warning: Incorrect settings may cause system malfunction. To correct it, restore the Setup Defaults with . Advanced Menu Selections You can make the following selections on the Advanced Menu. Feature Legacy USB Support Summary screen Boot-time Diagnostic Screen QuickBoot Mode Extended Memory Testing IGD - Boot Type Options Description Disabled Enable Disabled Enable Disabled Enable Disabled Enable Enable support for Legacy Universal Serial Bus Display system configuration on boot Display the diagnostic screen during boot Allows the system to skip certain tests while booting. This will decrease the time needed to boot the system. Determines which type of tests will be performed on extended memory (above 1M). Normal Just zero it None VBIOS Default Select the Video Device that will be 30 BIOS Setup Feature PS/2 Mouse PCI Express - Root Port 1 Options Description activated during POST CRT LFP CRT+LFP TV LFP-SDVO EFP TV-SDVO CRT+LFP-SDVO CRT+EFP Disabled Enable Auto Detect ’Disabled’ prevents any installed PS/2 mouse from functioning, but frees up IRQ 12. ’Enabled’ forces the PS/2 mouse port to be enabled regardless if a mouse is present. ’Auto Detect’ will enable the PS/2 mouse only if present. ’OS Controlled’ only displayed if the OS controls the mouse. Control the PCI Express Port via this setup option. Disabled Enable Auto Disabled - Port always disabled. Enabled - Port always enabled. Auto - Only enable if card found. USB - Device 29, Function 7 Passive Cooling Trip Point Note that if Root Port 1 is disabled, Root Ports 2-4 will be disabled as well. Control USB 2.0 functionality through this Setup Item Disabled Enable Disabled 15 C/23 C/31 C/39 C/ 47 C/55 C/63 C/71 C/ 79 C/87 C/95 C/103 C/ 111 C/119 C This value controls the temperature of the ACPI Passive Trip Point – the point in which the OS will begin throttling the CPU. Note: When the DTS is enabled, only values below 97C are valid. These items control the configuration of various National 393 SIO devices. SIO SMC227 CONFGURATION 31 BIOS Setup For most frequently altered setup “SIO SMC227 CONFIDURATION” please refers following: Warning: Incorrect settings in RS485/RS422 of COMx mode may cause SIO component Damage. Must be cautious before Setup. SIO SMC227 Configuration Sub-Menu Phoenix TrustedCore (tm) Setup Utility Advanced SIO SMC227 CONFIGURATION COM1 port: COM1 mode: COM2 port: COM2 mode: COM3 port: COM3 mode: COM4 port: COM4 mode: Printer1: Printer2: F1 Help Esc Exit [3F8-IRQ 4] [RS232] [2F8-IRQ 3] [RS232] [3E8-IRQ 10] [RS232] [2E8-IRQ 5] [RS232] [Disabled] [Disabled] ↑↓ Select Item ↔ Menu –/+ Change Values Enter Select ► Sub-Menu Item Specific Help Configure COM1 using device options: [Disabled] No configuration [3F8-IRQ 4] Set the base I/O address for COM1 F9 F10 Setup Defaults Save and Exit SIO SMC227 Configuration Sub-Menu Selections You can make the following selections on the SIO SMC227 Configuration submenu. Feature COM1 port Options Disabled 3F8-IRQ 4 COM1 mode RS232 TTL1 Description Configure COM1 using device options: [Disabled] No configuration [3F8-IRQ 4] Set the base I/O address for COM1 Configure UART mode options: [RS232]:External Device [TTL1]:Internal Device COM2 port Disabled 2F8-IRQ 3 Configure COM2 using device options: [Disabled] No configuration 32 BIOS Setup Feature COM2 mode Options RS232 TTL2 Description [2F8-IRQ 3] Set the base I/O address for COM2 Configure UART mode options: [RS232]:External Device [TTL2]:Internal Device COM3 port Disabled 3E8-IRQ 10 COM3 mode RS232 TTL3 COM4 port Disabled 2E8-IRQ 5 COM4 mode RS232 TTL4 Configure COM3 using device options: [Disabled] No configuration [3E8-IRQ 10] Set the base I/O address for COM3 Configure UART mode options: [RS232]:External Device [TTL3]:Internal Device Configure COM4 using device options: [Disabled] No configuration [2E8-IRQ 5] Set the base I/O address for COM4 Configure UART mode options: [RS232]:External Device [TTL4]:Internal Device Printer1 Disabled 378-IRQ 4 Printer2 Disabled 3BC Configure Printer1 device options: [Disabled] No configuration [378-IRQ 7] Set the base I/O address for Printer1 Configure Printer2 device options: [Disabled] No configuration [3BC] Set the base I/O address for Printer2 33 BIOS Setup Security Menu Warning: If you forget user/supervisor password, the computer has to send back to manufacturer and replace EEPROM to make it work again. Main Phoenix TrustedCore (tm) Setup Utility Security TPM State Boot Advanced Processor Serial Number Set Supervisor Password Set User Password Fixed disk boot sector: Diskette access: Password on boot: USB Interface: AC97 Audio Interface: AC97 Modem Interface: Cardbus/1394 Interface • RF Security Control: F1 Help Esc Exit ↑↓ Select ↔ Menu [Disabled] [Enter] [Enter] [Normal] [Supervisor] [Disabled] Exit Item Specific Help Controls detection of Processor Serial No. System must be reset or restarted from power-on for settings to take effect. [Enabled] [Auto] [Auto] [Auto] Item –/+ Change Values Enter Select ► Sub-Menu F9 F10 Setup Defaults Save and Exit Security Menu Selections You can make the following selections on the Security Menu. Feature Processor Serial Number Options Disabled Enabled Set Supervisor password Enter New Password Confirm New Password Description Controls detection of Processor Serial No. System must be reset or restarted from power-on for settings to take effect. Supervisor Password controls access to the setup utility. Set User Password Enter New Password Confirm New Password User Password controls access to the system at boot. Fixed disk boot sector Normal Write Protect Write protects boot sector on the hard disk to protect against viruses. Diskette access Supervisor Control access to diskette drives Password on boot Disabled Enabled Enables password entry on boot 34 BIOS Setup Feature USB Interface Options Disabled Enabled Description Control the listed USB Functions by setting the item to the desired value. AC97 Audio Interface Disabled Auto AC97 Modem Interface Disabled Auto Cardbus/1394 Interface Disabled Auto Control Detection of the AC97 Audio Device. Auto = AC97 Audio will be enabled if present, disabled otherwise. Disabled = AC97 Audio will be unconditionally disabled, regardless of presence. Control Detection of the AC97 Modem Device. Auto = AC97 Modem will be enabled if present, disabled otherwise. Disabled = AC97 Modem will be unconditionally disabled, regardless of presence. Cardbus Device Function Disable/Enable RF Security Control RF Security Control: Wireless LAN GPS 35 BIOS Setup For most frequently altered setup “RF Security Control” please refers following: RF Security Control Sub-Menu Phoenix TrustedCore (tm) Setup Utility Security RF Security Control: Wireless Lan: [Disabled] GPS: [Disabled] F1 Help Esc Exit ↑↓ Select ↔ Menu Item Item Specific Help Wireless Lan Control –/+ Change Values Enter Select ► Sub-Menu F9 F10 Setup Defaults Save and Exit RF Security Control Sub-Menu Selections You can make the following selections on the RF Security Control sub-menu. Feature Wireless Lan GPS Options Disabled Enabled Disabled Enabled Description Wireless Lan Control Enabled Wireless function GPS Control Enabled GPS function 36 BIOS Setup TPM State Menu Main Advanced Phoenix TrustedCore (tm) Setup Utility Security TPM State Boot Current TPM State: Change TPM State: Enabled and Deactivated [No Change] Exit Item Specific Help Change TPM State F1 Help Esc Exit ↑↓ Select ↔ Menu Item –/+ Change Values Enter Select ► Sub-Menu F9 F10 Setup Defaults Save and Exit TPM State Menu Selections You can make the following selections on the TPM State Menu. Feature Change TPM State Options No Change Enable & Activate Deactivate & Disable Clear Description Change TPM State 37 BIOS Setup Boot Menu Main Advanced Phoenix TrustedCore (tm) Setup Utility Security TPM State Boot Item Specific Help Boot priority order: 1: USB KEY: 2: USB FDC: 3: USB HDD: 4: IDE CD: 5: IDE HDD: 6: Legacy Network Card 7: PCI SCSI: 8: Excluded from boot order: : USB CDROM: : USB ZIP: : USB LS120: : PCI BEV: : Other USB: : PCI: : 1394 CDROM F1 Help Esc Exit ↑↓ Select ↔ Menu Item Exit Keys used to view or configure devices: Up and Down arrows select a device. <+> and <–> moves the device up or down. and specifies the device fixed or removable. excludes or includes the device to boot. enables or disables a device. <1 – 4> Loads default boot sequence. –/+ Change Values Enter Select ► Sub-Menu F9 F10 Setup Defaults Save and Exit The system will try to boot from device on top then the 2nd and so on. If there is more than one device in each category, only the device on top of sub-menu can boot up. 38 BIOS Setup Exit Menu Main Advance Phoenix TrustedCore (tm) Setup Utility Security TPM State Boot Exit Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes F1 Help Esc Exit ↑↓ Select ↔ Menu Exit System Setup and save your changes to CMOS. Item –/+ Change Values Enter Select ► Sub-Menu F9 F10 Setup Defaults Save and Exit Exit Menu Selections You can make the following selections on the Exit Menu. Feature Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Options Description Exit System Setup and save your changes to CMOS. Exit utility without saving Setup data to CMOS. Load default values for all SETUP items. Load previous values from CMOS for all SETUP items. Save Setup Data to CMOS Save Changes 39 Utilities and Drivers UTILITIES AND DRIVERS Note: Most device drivers are available in Windows. Only when the default driver does not work properly you need to install the factory bundled drivers. The utility CD includes most drivers of the computer’s installed devices. Consult dealer if any driver is missing. Re-install drivers or perform “Driver Update” to replace the Windows default drivers. Check readme.txt file on utility CD to get the newest information before starting to install drivers. Chipset Windows Driver Installation: Insert the Driver CD into the CD-ROM. Click infinst_autol.exe in the directory of DR8EX\Driver\Chipset\2kXpVista3264 then follow the prompt to complete installation. VGA Utility Display Capability Resolution & Color LCD RGB LCD + RGB 640x 480x 16-bit color 640x 480x 24-bit color 640x 480x 32-bit color 800x 600x 64K color 800x 600x 24-bit color 800x 600x 32-bit color 1024x 768x 16-bit color 1024x 768x 24-bit color 1280x 1024x 16-bit color 1280x 1024x 24-bit color 1280x 1024x 32-bit color 40 Utilities and Drivers Resolution & Color LCD RGB LCD + RGB 1600x 1200x 16-bit color 1600x 1200x 24-bit color 1600x 1200x 32-bit color 2048x 1536x 16-bit color 2048x 1536x 24-bit color 2048x 1536x 32-bit color The table lists typical display modes only. The system also supports standard video modes with lower resolution and color. Windows Driver Installation: Insert the Driver CD into the CD-ROM. Click win2k_xp1429.exe in the directory of DR8EX\Driver\VGA\Intel_945GM\2kXp32 then follow prompt to complete driver installation. Windows may recommend using their driver, but you should confirm to chang the factory bundled driver. After restart and back to Settings window, choose proper Colors and Screen Area. Audio Driver Windows Insert the Driver CD into the CD-ROM. Click WDM_A400.exe in the directory of DR8EX\Driver\Audio\2kXp_3264 then follow the prompt to complete installation. USB 2.0 Windows does not need driver. Touch Screen Driver Enter BIOS Setup screen and set COM1 port as “TTL1”. (COM1 has multiple connectivity, so it’s necessary to setup. The optional COM4 may be configured as touch screen and doesn’t need to configure the BIOS.) Afterwards, please cancel the prompt of installation wizard to setup the driver from the CD 41 Utilities and Drivers (\DR8EX\Driver\Touchscreen\DP9000\2kxpVista3264\PM...Universal…v1.0.0. 8), and follow the prompt to complete installation and then restart. PCMCIA Driver Windows The driver is automatically installed under Windows. Mini PCI 1G AX92200 LAN Insert the Driver CD into the CD-ROM. Click Setup.exe in the directory of E:\AX92200\DRIVER\RTL8110S\windows (612) then follow the prompt to complete installation. Mini PCI INT8100 LAN Windows does not need driver. Mini PCI-E 1G RTL8111B LAN Insert the Driver CD into the CD-ROM. Click setup.exe in the directory of DR8EX\Driver\PCIe_1G Lan\2kXp3264\RTL8168_8101E_664 then follow the prompt to complete installation. Mini PCI-E Intel 3945ABG WLAN *: For the driver and software to function correctly on Windows, the recommendation is to install Service Pack 4 or later. Ensure that MSI support level 3.1 or above is installed. Use the Windows Installer 3.1 v2 or greater. Insert the Driver CD into the CD-ROM. Click v11.1.0.5_xp32.exe in the directory of DR8EX\Driver\PCIe_Intel WLAN\2kXp32 then follow the prompt to complete installation. Fax/Modem Card Driver Insert the Driver CD into the CD-ROM. Click setup.exe in the directory of DR8EX\Driver\MDC\mdc_w2kxp then follow the prompt to complete installation. 42 Utilities and Drivers Wireless Manager For flight safety and power saving reason, there is a utility provided easily to enable/disable RF devices of Wireless LAN/ GPS in the run time. Insert the Driver CD into the CD-ROM. Click setup.exe in the directory of Utilities\Wireless Manager then follow the prompt to complete installation. Input Management Services Note: 1. This utility is valid for only Windows. 2. “Function Key Manager” is better for tablet. Install 1. Run setup.exe from the directory of “Input Management Services” and then follows the prompt to complete. Uninstall 1. Left-click the icon and then launch “Exit”. 2. Run “Uninstall” from the path of “Start/All Programs/Input Management Services”. 3. Do not uninstall form Add/Remove Program on Control Panel. Icon Function Left-click the icon , there are 5 items: 1. Function Key Manager 2. On-Screen Keyboard 3. Launch Function key manager at startup 4. Launch On-Screen keyboard at logon 5. Exit As the title is named, you could activate Function Key Manager and/or OnScreen Keyboard. 43 Utilities and Drivers In addition, if you activate “Launch Function key manager at startup”, will be on the task menu automatically after the system is launched. If you activate “Launch On-Screen keyboard at logon” and the log on password is set; OnScreen keyboard will pop-up automatically when system get into/recover from following modes, “Logon/Logoff”, “Standby/Resume”, “Boot/Reboot”, and “Hibernate/Resume”. However, On-Screen keyboard will disappear after password is input correctly and enter the Windows desktop and launch again. Launch Launch Function Key Manager, and this window will be shown: As “Function Key Manager” is titled, there are two function key sets (1 and 2). And eight function keys (Function 1 can be assigned from F1 to F8; Function 2 can be assigned from F2~F8) for each function key set could be defined by users. Each function key has 10 built-in functions. F1 is also used to switch between Function 1 & 2 set when “Toggle function 2” action is set; otherwise it’s same as other function keys. 1. None 2. Open/Execute a file 3. Open a URL in default browser 4. Replace with another key 5. Mouse cursor move to 6. Simulate mouse button click 44 Utilities and Drivers 7. 8. 9. 10. 11. 12. Change display output Rotate screen Change desktop background color Chang desktop wallpaper Launch On-Screen keyboard Toggle function 2 Some functions need to assign additional parameters to work properly. Assign parameter for a function, click the mouse left button on the same row parameter field to enter the parameter or assign option in the pop-up dialog. Please refer to the following descriptions. 1. Open/Execute a file Select a file from the pop-up window. Set the proper file type if necessary, batch file (*.bat) is the default. 2. Open a URL in default browser Input the address of the website, e.g. www.crete.com.tw. 3. Replace with another Key The single key or combination key can be used. For example, press “Ctrl” and” “x” simultaneously, {Ctrl} x will be shown in the parameter blank. It means the combination key of Ctrl and x. However, some combination keys are excluded. For example, “Ctrl+Alt+Del”, “Ctrl+Esc” and “Alt+Tab”; “Ctrl+Alt+Del” just jumps to run REAL “Ctrl+Alt+Del” right away, “Ctrl+Esc” goes to Start Menu, “Alt+Tab” will pop-up a window for selecting the working window. 4. Mouse cursor move to Used to control the mouse cursor moving directions. “Up”, “Down”, “Left” and “Right” are the candidates. 45 Utilities and Drivers 5. Simulate mouse button click Used to define two button clicks of the mouse. “Left button click” and “Right button click” are alternatives. 6. Change display output Switch display output among LCD, CRT and DVI. Just only one single mode can exist. “Enable External Monitor”, “Enable Notebook Display”, and “Enable External DVI” are the candidates. Please connect the external monitor or external DVI before launching this function. 7. Rotate screen The rotate setup provides four choices: Normal, 90, 180 and 270. 46 Utilities and Drivers Please make sure Intel Extreme Graphics 2 driver/Control Panel application is installed and this icon will be on the task menu. Activate the “Graphics Properties …” from “Graphics Options”. In the “Hot Keys”, activate “Enable Hot Keys”. 47 Utilities and Drivers In the “Rotation”, activate “Enable Rotation” and set the “Rotation Views” to “Normal”. It is recommended that to set a Function Key to work as “Rotate Screen” with parameter of “Normal” when you have set other keys to act as “Rotate Screen” with parameter of “90”, “180” or “270”. So you could change display between “Normal” and rotation of “90”, “180” or “270”. Note: If you have suffered from the mask of 90/270 Degree as shown in the following window. The rotation of 90/270 cannot work correctly. 48 Utilities and Drivers It results from “Hide modes that monitor cannot display” is enabled. So in such a situation, uncheck this box to enable all rotation views under Control Panel/Display/Display Properties/Setting/Advanced/Monitor. 49 Utilities and Drivers If you rotate screen to “Normal”, the “System Properties” windows will popup. 8. Change desktop background color Used to change background color to make display more readable in the day or night. Select a color from the pop-up color palette. 9. Change desktop wallpaper Used to change wallpaper to make display more readable in the day or night. Select a file from the pop-up window. Set the proper file type if necessary, bitmap Files (*.bmp) is the default. 10. Launch On-Screen keyboard On-Screen keyboard is a utility that displays a virtual keyboard on the computer screen. Especially it is useful for tablet PC users; users could type data by using a pointing device or joystick. You can toggle this function key to enable/disable the on-screen keyboard. 11. Toggle function 2 This is only for “F1” in “Function 1” and no parameter has to be added. You can toggle this “F1” to launch the function key between “Function 1” and “Function 2”. The top banner of activated area will be changed into pink and the icon will show for “Function 1” or for “Function 2”. When you have set this “Toggle function 2”, you could get additional 6 function keys in “Function 2”. In other words, 6 function keys in “Function 1” and 6 function keys in “Function 2” make 12 function keys in this Function Key Manager. 50 Maintenance/Service MAINTENANCE/SERVICE Cleaning ALWAYS turn OFF the power, unplug the power cord and remove the battery before cleaning. The exterior of the system and display may be wiped with a clean, soft, and lintfree cloth. If there is difficulty removing dirt, apply non-ammonia, non-alcohol based glass cleaner to the cloth and wipe. An air gun is recommended for cleaning water and dust. For salty water please clean with fresh water then blow-dry with an air gun. Troubleshooting Should the computer fail to function properly, the troubleshooting steps below may be followed. - Check AC/vehicle adapter, battery, and the power source. - Minimize the configuration, i.e. remove extra peripherals and devices. - Remove the modules one by one (HDD, CD-ROM, Battery, etc.). - Remove the software suspected. - Set BIOS fail-safe default. - Re-install operating system and application software. RMA Service If troubleshooting steps are unsuccessful, consult your dealer for RMA. Shipping instructions: 1. Remove any personal add-on devices or other media. 2. Use the original shipping container and packing materials, if possible. 3. If the original packing materials are not available, wrap the equipment with soft material (e.g. PU/PE form) then put the wrapped equipment into a hard cardboard shipping box. 4. Include a sheet with the following information: (Note: Please keep a copy of this sheet for your records.) - Name 51 Maintenance/Service 5. 6. Address Unit serial number Place and date of purchase or the original invoice number Date of failure A DETAILED description of the problems you have encountered including: The operating system, the add-on device installed (if any), the application software, the failure phenomenon, etc. - A list of the hardware/software configuration, if applicable. Clearly mark the outside of the shipping box with the RMA #. If an RMA # is not present on the shipping box, receiving will be unable to identify it and it might be returned. Unless prior arrangements have been made, the customer is responsible for all shipping costs. Unauthorized use of the company’s shipping accounts is not permitted. 52 Recycled/Recycleable Printed in Taiwan P/N: G630802000B
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Encryption : Standard V2.3 (128-bit) User Access : Print, Extract XMP Toolkit : 3.1-701 Creator Tool : PScript5.dll Version 5.2 Modify Date : 2008:09:11 16:31:08+08:00 Create Date : 2008:09:01 11:13:25+08:00 Metadata Date : 2008:09:11 16:31:08+08:00 Format : application/pdf Title : Microsoft Word - DR886_User_Guide_080901.doc Creator : janice Producer : Acrobat Distiller 8.1.0 (Windows) Document ID : uuid:3328e311-cd2e-422a-b303-668145ea9a57 Instance ID : uuid:15dc98ff-274b-4562-982d-98ee20be1ed4 Page Count : 62 Author : janiceEXIF Metadata provided by EXIF.tools