Mipro Electronics Co TA8018 Digital Plug-on Transmitter User Manual TA 80 2CE547B 201611

Download:
Mirror Download [FCC.gov]
Document ID	3836720
Application ID	VjukytNUNLx4VMC4A3hDXA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	52.04kB (650531 bits)
Date Submitted	2018-05-02 00:00:00
Date Available	2018-05-02 00:00:00
Creation Date	2016-10-05 08:36:51
Producing Software	Corel PDF Engine Version 3.0.0.739
Document Lastmod	0000-00-00 00:00:00
Document Title	TA-80(2CE547B)_201611.cdr
Document Creator	CorelDRAW
Document Author:	fay

User Guide
TA-80
Digital Plug-on Transmitter
All rights reserved. MN 016/11
Do not copy or forward without prior approvals MIPRO.
Specifications and design subject to change without notice.
2 CE 5 4 7 B
Digital Plug-on Transmitter
Contents
Digital Plug-on Transmitter
Transmitter Controls and Indicators
Transmitter Controls and Indicators
Operating Instructions
How to Setup Transmitter Parameters
14 Battery Status
17 MUTE (ON/OFF)
18 Insertion and replacing the batteries
19 MP-80 Battery Charger (Optional)
20 MP-20 Dual-Slot Battery Charger
(Optional)
12
13
10
11
Microphone Input: XLR-3 socket (female,
balanced).
Housing: Metal transmitter body.
LCD Panel: Display transmitter parameters.
Power Button: Press and hold 2 seconds to
power ON or OFF.
Digital Plug-on Transmitter
MODE Button: Allows access to available
functions displaying in LCD panel.
SET Button: Parameter selection button.
ACT IR Port: Align and syncs the transmitter
and receiver frequency automatically.
Battery cover lock: Lockable battery cover.
Mute Switch: Muted (red light is on);
Not muted (red light is off).
Digital Plug-on Transmitter
Operating Instructions
10
Battery Cover: Hinged cover opens to provide
access to one 18500 rechargeable battery.
11
Battery Compartment: Accommodates one
18500 rechargeable battery.
12
Charge Contacts Holder: Fixed.
11
Charge Contacts: Align correctly to charge.
Ascertain a wired microphone is plugged-in prior
to power on the transmitter to prevent noise
interference.
Tighten the mechanical locking ring in a
clockwise direction for a secured fit
(see diagram 1).
Unplug the microphone in a counter-clockwise
direction.
Standard wired
microphone XLR balanced
output connector holder
Pin1
Pin3
Pin2
The ridge on the
connector must align and
match the indentation on
the socket when inserting
for a proper fit.
(diagram 1)
XLR balanced microphone
connection pin name and function
Pin 1: Ground Pin (Negative
phantom power)
Pin 2: AF+ (HOT) Positive phase
input pin (String 6.8KΩ
resistance to positive
phantom power)
Pin 3: AF-(COOL)Negative phase
input pin (String 6.8KΩ
resistance to positive
phantom power)
Digital Plug-on Transmitter
Digital Plug-on Transmitter
LCD Display Screen
GRP - CH
01 - 01
GRP - CH
P00
FREQ.
AF GAIN
P00
0 dB
ENCRYPT
P00
515.100
01 - 01
P00
P00
NO

1 LCD Screen
AF LIMIT P00
AF L-CUT
YES
L - CUT
P00
RF POWER P00
AF PHASE P00
PHANTOM P00
HIGH
NORM
OFF
2 Parameters Screen

3 AF (audio) MUTE

SET LOCK P00
4 Phantom Power Status
UNLK
5 Transmitter Battery Meter

a Group and Channel
How to Setup Transmitter Parameters
b Frequency
c Sensitivity Level
MODE Button:
d AF Low Cut
Press “MODE” button to access one of the
functions below.
e AF Limit
SET Button:
Press “SET” button and LCD wills start flashing.
During flashing, press SET button to change
parameters.
GRP - CH
Encryption
g RF Output Power
h AF Phase
Phantom Power
Parameters Lock & Unlock Status
P00
01 - 01
SET
MODE
Digital Plug-on Transmitter
GRP-CH: Displays Group and Channel Information
a. Press MODE and stop on the GRP-CH function;
the display showing the current group and
channel will be flashing. After 30 seconds, the
display will stop flashing and the current group
and channel selection will be set.
b. The group and channel information is now
shown on the display. Changing the current
group and channel must be done on the
receiver.
GRP - CH
Digital Plug-on Transmitter
FREQUENCY: Displays Transmitter Frequency
Information
a. Press MODE and stop on the FREQUENCY
function; the display showing the current
frequency will be flashing. After 30 seconds, the
display will stop flashing.
b. The frequency information is now shown on the
display. Changing the current frequency must be
done on the receiver.
c. To modify the transmitter's group, channel and
frequency, all three must be set at the receiver
and the new setting transmitted to the
transmitter via the ACT function.
P00
01 - 01
d. Programming and saving Frequency need to be
synced by pressing “ACT” button on the receiver.
c. Programming and saving Group and Channel
need to be synced by pressing “ACT” button on
the receiver.
FREQ.
d. When programming a special frequency via
monitoring software, the LCD screen cannot
display the number. This is because this special
channel is not in the preset group and channel.
RF, the LCD panel will look like the illustration
below.
GRP - CH
P00
P00
515.100
Digital Plug-on Transmitter
AF GAIN: Setup and Change of Input Sensitivity
Digital Plug-on Transmitter
a. AF gain -18dB ~ 30dB in 6dB increment.
AF L-CUT: Setup and Change of Low
Frequency Cut Off
b. Press MODE and stop on the AF GAIN function;
the display showing the current status will be
flashing and is ready to be modified.
a. Press MODE and stop on the AF L-CUT
function; the display showing the current status
will be flashing and is ready to be modified.
c. Press SET button to set dB value. -18dB ~ 30dB
in 6dB increment
b. Press the SET button while the display is
flashing to change to L-CUT or FLAT as desired.
d. Screen stops flashing and remains in the set
state if not operated within 30 seconds.
c. Screen stops flashing and remains in the set
state if not operated within 30 seconds.
e. The higher the gains are set, the lower the
dynamic range for signal input and the greater
the danger of unwanted noises and feedback
getting into the system.
f.
d. When the AF L-CUT function is L-CUT, the
frequency response below 100Hz will decrease
about 3dB with a slope of -6dB/Octave.
When using electronic guitar, gain should set at
0dB.
g. Please make sure input signal strength does not
exceed 2 Vrms (gain=6dB) as it is the maximum
input strength allowed for transmitter without
causing distortion.
h. When the gain is set at -12dB or -18dB it
stands up to 20Vp-p input signals. Signals cut
off when it exceeds this level
AF GAIN
P00
-18 dB
AF GAIN
P00
-12 dB
AF GAIN
AF L-CUT
P00
L - CUT
AF L-CUT
P00
FLAT
AF LIMIT: Setup and Change of Input Limit
a. Press MODE and stop on the AF LIMIT
function; the display showing the current status
will be flashing and is ready to be modified.
P00
b. Press SET while the display is flashing to change
the setting to YES or NO.
-6 dB
c. Screen stops flashing and remains in the set
state if not operated within 30 seconds.
AF GAIN
P00
12 dB
AF GAIN
18 dB
AF GAIN
P00
6 dB
P00
AF GAIN
24 dB
AF GAIN
P00
d. When the LIMIT is YES, the maximum output of
the receiver is limited to 1V.
0 dB
P00
AF GAIN
P00
30 dB
AF LIMIT P00
AF LIMIT P00
YES
NO
Digital Plug-on Transmitter
Digital Plug-on Transmitter
ENCRYPTION: Displays Information of Encryption
RF POWER: RF Power Selection
a. Press MODE and stop on the ENCRYPTION
function; the display showing the current status
will be flashing.
a. Press MODE button for selection of RF POWER.
Selection of HIGH or LOW can be selected once
the RF POWER LCD starts blinking.
b. Screen stops flashing and remains in the set
state if not operated within 30 seconds.
b. Press SET button to select and set HIGH or
LOW.
c. The ENCRYPTION function displays status
information only. Changing of the current status
must be done from the receiver via the ACT
function.
c. Screen stops flashing and remains in the set
state if not operated within 30 seconds.
d. The ENCRYPTION function must be set at
receiver first then using ACT to program the
transmitter.
ENCRYPT
d. HIGH has 50mW transmitting power. LOW has
10mW transmitting power. Set appropriate
power to meet region/country regulations.
P00
NO
10
11
RF POWER P00
RF POWER P00
HIGH
LOW
Digital Plug-on Transmitter
Digital Plug-on Transmitter
AF PHASE: Phase Selection of AF inputs
PHANTOM: Phantom Power
a. Press MODE button for selection of AF PHASE.
Selection of NORM or INVER can be selected
once the AF PHASE LCD starts blinking.
a. Press the MODE button to select the PHANTOM
screen, the LCD screen will start flashing in the
current set state and is ready for change.
b. Press SET button to select and set NORM or
INVER.
b. Press the SET button to set OFF, 12V or 48V.
c. The screen will stop flashing and remain in the
set state if not operated within 30 seconds.
c. NORM: AF input is positive (positive polarity)
INVER: AF input is negative (reverse polarity)
d. PHANTOM is phantom power setting function,
providing three selections: 12V or 48V or OFF,
d. Screen stops flashing and remains in the set
state if not operated within 30 seconds.
e. AF PHASE function provides users a phase
selection for different condenser microphones.
The normal setting is NORM, and INVER might
be selected if two-wire condenser microphone is
used.
AF PHASE P00
AF PHASE P00
NORM
INVER
12V or 48V is normally set for an external
wired condenser microphone;
OFF is normally set for an external wired
dynamic microphone.
e. A general wired microphone with phantom
power is allowed to use in 12V ~ 48V phantom
power supply range. If it is determined that the
phantom power wired microphone can operate
at 12V, it is strongly recommended to be set to
12V, it reduces transmitter power consumption
significantly & extends battery life.
f.
Phantom Power Status: P00 is turned off (OFF);
P12 indicates 12V phantom power; P48 indicates
48V phantom power.
g. Maximum power supply of 10mA up to 48V
phantom power usage. However, observe the
total power consumption will increase
significantly and battery life will therefore be
reduced by 50% or more.
12
13
PHANTOM P00
PHANTOM P12
PHANTOM P48
OFF
12V
48V
Digital Plug-on Transmitter
Digital Plug-on Transmitter
SET LOCK: Setup and Change of Parameter Lock
“OFF...” : Power Off
a. Press MODE button once for SET LOCK display.
Once SET LOCK display starts blinking it is ready
for selection.
1. Press and hold power button for 2 seconds to
power on & off.
b. Press SET button for UNLK or LOCK selection.
c. When locked (LOCK), receiver settings cannot
be changed including the powering on &
powering off. To power off it needs to be in
unlock mode (UNLOCK).
2. When the power switch is turned off, the LCD
will show “OFF…” (for Power Off) first and then
the system will shut down and no further
messages will be displayed.
d. A sudden lose of power will deactivate the LOCK
Function.
SET LOCK P00
SET LOCK P00
UNLK
LOCK
OFF...
Battery Status
Indicates the power remaining in the transmitter
battery. When the battery has less than 10% power
remaining it must be replaced or recharged. If an
under voltage condition continues, the LCD will
show “OFF...” and the system will shut down to
prevent being overly discharged.
100%
80%
60%
40%
20%
10%
14
15
Digital Plug-on Transmitter
Digital Plug-on Transmitter
MUTE (ON/OFF)
ERR: Error Code
If the LCD displays “ERR” after turning on the
power, it indicates the operation is not correct. The
error codes are as follows:
ROM-ER →Transmitter does not have the initial
data so the microphone is completely
dead and cannot be programmed.
1.
Light on : “Muted”.
2.
Light off : “Not Muted”.
3. MUTE setting is not affected in LOCK mode.
ERROR1 →Failure on RF circuitry, frequency cannot
be programmed.
NO-03
NO-04
→Frequency to be programmed into the
transmitter exceeds the highest
frequency of the designated frequency
band of the transmitter.
→Frequency to be programmed into the
transmitter exceeds the lowest
frequency of the designated frequency
band of the transmitter.
MUTE
GRP - CH
FREQ.
P00
MUTE
P00
515.100
AF MUTE
AF MUTE
**Note:
GRP - CH
NO-03 and NO-04 will not change the
transmitter's original frequency and the
transmitter will still operate normally with the
error message on display. To remove the error
message from the display panel, please switch
off the transmitter and switch it on again.
P00
01 - 01
FREQ.
P00
515.100
AF MUTE
AF MUTE
AF GAIN
P00
0 dB
AF MUTE
AF LIMIT P00
AF L-CUT
NO
YES
L - CUT
RF POWER P00
AF PHASE P00
PHANTOM P00
HIGH
NORM
OFF
ENCRYPT
P00
AF MUTE
AF MUTE
AF MUTE
AF MUTE
P00
AF MUTE
AF MUTE
SET LOCK P00
UNLK
AF MUTE
16
17
Digital Plug-on Transmitter
Insertion and replacing the batteries
1. Push up the battery
cover lock towards
outward direction,
and push the battery
cover sideway to
open.
Digital Plug-on Transmitter
MP-80 Battery Charger (Optional)
TA-80 transmitter and/or an additional 18500
recharge battery can be both recharged
simultaneously in MP-80.
TA-80
2. Ready for a 18500
rechargeable battery
insertion or
replacement.
Battery
Adaptor
18500
Rechargeable
Batteries
3. Insert one 18500
rechargeable battery
as shown below with
positive (+) end
towards inside
compartment.
4. Push the battery
cover back for a
secured lock.
5. Make sure the battery
cover is locked and
tightly secured.
Attention:
Power off the transmitter to avoid additional battery
use. Remove the battery if it will not be used for an
extended periods of time.
18
Insert the TA-80 into
a supplied battery
adaptor first before
place into the MP-80
for charging.
19
Insert one or two
18500 rechargeable
batteries into MP-80
according to the
correct polarity.
Digital Plug-on Transmitter
MP-20 Dual-Slot Battery Charger
(Optional)
Use the Battery Charger to charge up to two
rechargeable 18500 Li-ion batteries for
rechargeable MIPRO handheld or bodypack
transmitter.
Charging Batteries: Insert the batteries with the
correct positive (+) & negative (-) polarity and plug
the charger into a power outlet, as shown here.
Charge Status: The indicator light displays the
charging status of the batteries.
FCC Statement
FCC Caution: To assure continued compliance, any
changes or modifications not expressly approved
by the party responsible for compliance could void
the user's authority to operate this equipment.
(Example - use only shielded interface cables when
connecting to computer or peripheral devices).
This device complied with FCC radiation exposure limits as
set forth for an uncontrolled environment.
This device should be installed and operated so that its
antenna(s) are not co-located or operating in conjunction
with any other antenna or transmitter.
Still Red: The batteries are charging.
Still Green: The batteries are charged and ready
to use.
Flashing Light: May indicate any of the following
conditions:
a. The batteries haven’t been properly installed
in the charger.
FCC
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
Industry Canada Statement
This device complies with Industry Canada licenceexempt RSS standard.
b. An unsupported type of battery is in the
charger.
c. The batteries may be faulty or damaged and
should be replaced.
Rechargeable 18500 Li-ion
Batteries
(Transformer is shown here for reference only)
Digital Plug-on Transmitter
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference,
including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR
d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes : (1) l'appareil ne doit
pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
20
21
Digital Plug-on Transmitter
WARNING
1.
FOR OUTDOOR USE:
To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.
2.
UNDER WET LOCATION:
Apparatus should not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases should be placed on the apparatus.
3.
SERVICE INSTRUCTIONS:
CAUTION - These servicing instructions are for use by
qualified service personnel only. To reduce the risk of
electric shock, do not perform any servicing other than
that contained in the operating instructions unless you
are qualified to do so.
Digital Plug-on Transmitter
Notes
1. Refer to actual product in the event of product
description discrepancy.
2. Frequency range and maximum deviation comply
with the regulations of different countries.
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
within this unit.
This symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.
Disposal Dispose of any unusable devices or batteries
responsibly and in accordance with any
applicable regulations.
Disposing of used batteries with domestic waste
is to be avoided!
2005-08-13
Batteries / NiCad cells often contain heavy
metals such as cadmium(Cd), mercury(Hg) and
lead(Pb) that makes them unsuitable for
disposal with domestic waste. You may return
spent batteries/accumulators free of charge to
recycling centres or anywhere else batteries/
accumulators are sold.
By doing so, you contribute to the conservation
of our environment!
22
23

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : fay
Create Date                     : D:20161005083651
Creation Date--Text             : 
Modify Date                     : 0000:01:01 00:00:00
Mod Date--Text                  : 
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : fay
Title                           : TA-80(2CE547B)_201611.cdr
Producer                        : Corel PDF Engine Version 3.0.0.739
Creator Tool                    : CorelDRAW
Metadata Date                   : 2018:05:02 13:06:45+08:00
Document ID                     : uuid:524ecbf2-9cb8-4158-a582-90376de812b2
Instance ID                     : uuid:abcaccae-b094-4334-b214-a026df72315e
Page Count                      : 13

EXIF Metadata provided by EXIF.tools