Mitsumi Electric Co DRTW127 NFC Module User Manual DRT W127 User Manual 120725

Download:
Mirror Download [FCC.gov]
Document ID	1752131
Application ID	QgwqYhuwphVAW0R86MsZQA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	3.23kB (40378 bits)
Date Submitted	2012-07-25 00:00:00
Date Available	2012-09-08 00:00:00
Creation Date	2012-07-25 17:47:38
Producing Software	Acrobat Distiller 9.3.3 (Windows)
Document Lastmod	2012-07-25 17:47:38
Document Title	Microsoft Word - DRT-W127_User_Manual_120725.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	29253

User Manual
NFC Module
MODEL DRT-W127
The purpose of this manual is to explain correct way how to integrate module
DRT-W127 to the end product. It includes procedures that shall assist you to avoid
unforeseen problems. This manual presents information that shows how module
and OEM product, where module integrated, complies with regulations in certain
regions. Any modifications, not expressly approved by the manufacturer could void
the authority to operate in these regions.
The NFC Module, model DRT-W127 has to be installed and used in accordance
with the technical description/installation instructions provided by the manufacturer.
For detail information concerning type approval of this module (e.g. where this
module is already pre-approved) please contact the authorized local distributor or
the manufacturer.
The system may only be implemented in the configuration that was authorized.
Note that any changes or modifications to this equipment not expressly approved
by the manufacturer could void the user’s authority to operate this equipment.
Regulatory Information
Operational Information
Wireless Interoperability
The end product integrating this module is designed to be interoperable with any
NFC Card Reader/Writer product that is based on ISO18092, ISO14443A/B and
JIS X 6319-4 for Contactless integrated circuit card technology and to comply with
the following standards.
･ISO/IEC 18092 Near Field Communication – Interface and Protocol
･ISO/IEC 14443A/B 13.56MHz Contactless integrated circuit card - Proximity card
･JIS X 6319-4 13.56MHz Contactless integrated circuit card-Proximity card
Safety
The end product integrating this module, like other radio devices, emits radio
frequency electromagnetic energy. The level of energy emitted by this device,
however, is less than the electromagnetic energy emitted by other wireless devices
such as mobile phones. The end product integrating this module operates within
the guidelines found in radio frequency safety standards and recommendations.
These standards and recommendations reflect the consensus of the scientific
community and result from deliberations of panels and committees of scientists
who continually review and interpret the extensive research literature. In some
situations or environments, the use of the end product integrating this module may
be restricted by the proprietor of the building or responsible representatives of the
applicable organization. Examples of such situations include the following:
･Using the end product integrating this module onboard airplanes, or
･Using the end product integrating this module in any other environment
where the risk of interference with other devices or services is perceived or
identified as being harmful.
If uncertain of the policy that applies to the use of wireless devices in a specific
organization or environment (an airplane, for example), ask for authorization to use
the end product integrated into this module before turning it on.
USA-Federal Communications Commission (FCC)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
Caution
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Labeling
MITSUMI NFC Card Reader/Writer MODULE DRT-W127 labeled as below.
FCC ID: EW4DRTW127
The label with FCC ID is to be placed on the module. If FCC ID is not visible when
the module is installed into the system, “Contains FCC ID: EW4DRTW127” shall be
placed on the outside of final host system.
Caution: Exposure to Radio Frequency Radiation.
This device must not be co-located or operating in conjunction with any other
antenna or transmitter.
Instructions to OEM Integrators
A User manual provided to the end user must indicate the operating requirements
and conditions that must be observed to ensure compliance with the
above-mentioned FCC RF Exposure guideline.
If this module is intended for use in a portable device, integrators are responsible
for separate evaluation and/or approval to satisfy FCC RF Exposure requirements.
Only the antenna (Type: PCB Loop antenna) used during testing can be used with
this module.
Canada-Industry Canada (IC)
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
Labeling
MITSUMI NFC Card Reader/Writer MODULE DRT-W127 labeled as below.
IC: 4250A-DRTW127
The label with IC No. is to be placed on the module. If IC No. is not visible when the
module is installed into the system, “Contains IC: 4250A-DRTW127” shall be
placed on the outside of final host system.
The term “IC” before the equipment certification number only signifies that the
Industry Canada technical specifications were met.
Caution: Exposure to Radio Frequency Radiation.
This device must not be co-located or operating in conjunction with any other
antenna or transmitter.
Instructions to OEM Integrators
A User manual provided to the end user must indicate the operating requirements
and conditions that must be observed to ensure compliance with the
above-mentioned IC RF Exposure guideline.
If this module is intended for use in a portable device, integrators are responsible
for separate evaluation and/or approval to satisfy IC RF Exposure requirements.
Only the antenna (Type: PCB Loop antenna) used during testing can be used with
this module.
Europe-EU Declaration of Conformity and Restrictions
Hereby, MITSUMI declares that this MITSUMI NFC Card Reader/Writer MODULE
DRT-W127 is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
This equipment is marked with the
symbol and can be used throughout the
European community.
This indicates compliance with the R&TTE Directive 1999/5/EC and meets the
relevant parts of following technical specifications:
EN 300 330-2, Electromagnetic compatibility and Radio spectrum Matters (ERM);
Short Range Devices (SRD); Radio equipment in the frequency range 9 kHz to 25
MHz and inductive loop systems in the frequency range 9 kHz to 30 MHz; Part 2:
Harmonized EN covering the essential requirements of article 3.2 of the R&TTE
Directive
EN 301 489-3, Electromagnetic compatibility and Radio spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services;
Part 3: Specific conditions for Short-Range Devices (SRD) operating on
frequencies between 9 kHz and 40 GHz
EN 60950-1, Information technology equipment - Safety - Part 1: General
requirements
EN 50364, Limitation of human exposure to electromagnetic fields from devices
operating in the frequency range 0 Hz to 300 GHz, used in Electronic Article
Surveillance (EAS), Radio Frequency Identification (RFID) and similar applications
Remark:
This module is fore a fixed application only. The OEM integrator will need to
conduct full EMS testing in accordance with EN301 489-3 in the final use
configuration.
Caution: Exposure to Radio Frequency Radiation.
This device must not be co-located or operating in conjunction with any other
antenna or transmitter, without further RF Exposure evaluation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : 29253
Create Date                     : 2012:07:25 17:47:38+09:00
Modify Date                     : 2012:07:25 17:47:38+09:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 9.3.3 (Windows)
Format                          : application/pdf
Title                           : Microsoft Word - DRT-W127_User_Manual_120725.doc
Creator                         : 29253
Document ID                     : uuid:5438ed55-e21e-4d28-8b8c-40a87825525b
Instance ID                     : uuid:310e4f23-d74d-4e77-a2a8-139bbef05313
Page Count                      : 5

EXIF Metadata provided by EXIF.tools