Mitsumi Electric Co DWMW051 WiFi Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1741575
Application ID	Vw1gGmfLZpUHzOqJmxQr+g==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	3.51kB (43850 bits)
Date Submitted	2012-07-11 00:00:00
Date Available	2012-07-11 00:00:00
Creation Date	2012-07-11 15:44:52
Producing Software	Acrobat Distiller 9.3.3 (Windows)
Document Lastmod	2012-07-11 15:44:52
Document Title	Microsoft Word - User_Manual_DWM-W051_r4_120711.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	29253

User Manual
MITSUMI WiFi Module
MODEL DWM-W051
The purpose of this manual is to explain correct way how to integrate module
DWM-W051 to the end product. It includes procedures that shall assist you to avoid
unforeseen problems. This manual presents information that shows how module
and OEM product, where module integrated, complies with regulations in certain
regions. Any modifications, not expressly approved by the manufacturer could void
the authority to operate in these regions.
The MITSUMI WiFi Module, model DWM-W051 has to be installed and used in
accordance with the technical description/installation instructions provided by the
manufacturer.
For detail information concerning type approval of this module (e.g. where this
module is already pre-approved) please contact the authorized local distributor or
the manufacturer.
The system may only be implemented in the configuration that was authorized.
Note that any changes or modifications to this equipment not expressly approved
by the manufacturer could void the user’s authority to operate this equipment.
Regulatory Information
Operational Information
Wireless Interoperability
The end product integrating this module is designed to be interoperable with any
wireless LAN product that is based on direct sequence spread spectrum (DSSS)
and orthogonal frequency division multiplexing (OFDM) radio technology and to
comply with the following standards.
･IEEE Std 802.11b Standard on 2.4GHz Wireless LAN
･IEEE Std 802.11g Standard on 2.4GHz Wireless LAN
･IEEE Std 802.11ｎ Standard on 2.4GHz Wireless LAN
Safety
The end product integrating this module, like other radio devices, emits radio
frequency electromagnetic energy. The level of energy emitted by this device,
however, is less than the electromagnetic energy emitted by other wireless devices
such as mobile phones. The end product integrating this module operates within
the guidelines found in radio frequency safety standards and recommendations.
These standards and recommendations reflect the consensus of the scientific
community and result from deliberations of panels and committees of scientists
who continually review and interpret the extensive research literature. In some
situations or environments, the use of the end product integrating this module may
be restricted by the proprietor of the building or responsible representatives of the
applicable organization. Examples of such situations include the following:
･Using the end product integrating this module onboard airplanes, or
･Using the end product integrating this module in any other environment
where the risk of interference with other devices or services is perceived or
identified as being harmful.
If uncertain of the policy that applies to the use of wireless devices in a specific
organization or environment (an airplane, for example), ask for authorization to use
the end product integrated into this module before turning it on.
USA-Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy. If not installed and used in accordance with the instructions, it may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
tuning the equipment off and on, the user is encouraged to try and correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the distance between the equipment and the receiver.
-Connect the equipment to outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
CAUTION:
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Labeling:
MITSUMI WiFi module DWM-W051 labeled as below.
FCC ID: EW4DWMW051
The proposed with FCC ID label format is to be placed on the module. If FCC ID is
not visible when the module is installed into the system, “Contains FCC ID:
EW4DWMW051” shall be placed on the outside of final host system.
Caution: Exposure to Radio Frequency Radiation.
To comply with FCC RF exposure compliance requirements, a separation distance
of at least 20 cm must be maintained between the antenna of this device and all
persons. This device must not be co-located or operating in conjunction with any
other antenna or transmitter.
Instructions to OEM Integrators
A User manual provided to the end user must indicate the operating requirements
and conditions that must be observed to ensure compliance with the
above-mentioned FCC RF Exposure guideline.
If this module is intended for use in a portable device, integrators are responsible
for separate evaluation and/or approval to satisfy FCC RF Exposure requirements.
The antenna used this module is as follows;
Antenna Type: PIFA
Antenna Gain: 2.05dBi
If an antenna with higher gain or new antenna type is used with this module,
integrators must contact Mitsumi for additional testing and submission to the FCC.
If other radio devices are to be integrated with this module, an additional evaluation
and FCC submission may be required. Integrators are responsible for such
additional evaluation and FCC submission.
Canada-Industry Canada (IC)
This device complies with RSS 210 of Industry Canada.
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause
undesired operation of this device.
L ‘ utilization de ce dispositif est autorisée seulement aux conditions suivantes :
(1) il ne doit pas produire de brouillage et
(2) l’ utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique
reçu, même si ce brouillage est susceptible de compromettre le fomctionnement du
dispositif.
To reduce potential radio interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated power (EIRP) is not
more than that required for successful communication.
Labeling:
MITSUMI WiFi module DWM-W051 labeled as below.
IC: 4250A-DWMW051
The proposed with IC ID label format is to be placed on the module. If IC ID is not
visible when the module is installed into the system, “Contains IC:
4250A-DMW051” shall be placed on the outside of final host system.
Caution: Exposure to Radio Frequency Radiation.
To comply with IC RF exposure compliance requirements, a separation distance of
at least 20 cm must be maintained between the antenna of this device and all
persons. This device must not be co-located or operating in conjunction with any
other antenna or transmitter.
Instructions to OEM Integrators
A User manual provided to the end user must indicate the operating requirements
and conditions that must be observed to ensure compliance with the
above-mentioned IC RF Exposure guideline.
If this module is intended for use in a portable device, integrators are responsible
for separate evaluation and/or approval to satisfy IC RF Exposure requirements.
The antenna used this module is as follows;
Antenna Type: PIFA
Antenna Gain: 2.05dBi
If an antenna with higher gain or new antenna type is used with this module,
integrators must contact Mitsumi for additional testing and submission to the IC.
If other radio devices are to be integrated with this module, an additional evaluation
and IC submission may be required. Integrators are responsible for such additional
evaluation and IC submission.
Europe-EU Declaration of Conformity and Restrictions
Hereby, MITSUMI declares that this Mitsumi WiFi module DWM-W051 is in
compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
This equipment is marked with the
symbol and can be used throughout the
European community.
This indicates compliance with the R&TTE Directive 1999/5/EC and meets the
relevant parts of following technical specifications:
EN 300 328, Electromagnetic compatibility and Radio spectrum Matters (ERM);
Wideband Transmission Systems; Data transmission equipment operating in the
2.4GHz ISM band and using spread spectrum modulation techniques; Harmonized
EN covering essential requirements under article 3.2 of the R&TTE Directive.
EN 301 489-17, Electromagnetic Compatibility and Radio spectrum Matters (ERM);
Electromagnetic Compatibility (EMC) standard for radio equipment and services;
Part 17: Specific Conditions for Wideband Data and HYPERLAN Equipment.
EN 60950-1, Safety of Information Technology Equipment.
EN 62311, Assessment of electronic and electrical equipment related to human
exposure restrictions for electromagnetic fields (0 Hz-300 GHz).
Marking by the symbol
indicates that usage restrictions apply.
France – 2.4GHz for Metropolitan France :
In all Metropolitan départements, wireless LAN frequencies can be used under the
following conditions, either for public or private use:
･ Indoor use: maximum power (EIRP) of 100mW for the entire 2400-2483.5MHz
frequency band
･ Outdoor use: maximum power (EIRP) of 100mW for the 2400-2454MHz band
and with maximum power (EIRP) of 10mW for the 2454-2483.5MHz band
Remark:
This module is for a fixed application only. The OEM integrator will need to conduct
full EMS testing in accordance with EN301 489-17 in the final use configuration.
Caution: Exposure to Radio Frequency Radiation.
This device must not be co-located or operating in conjunction with any other
antenna or transmitter.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : 29253
Create Date                     : 2012:07:11 15:44:52+09:00
Modify Date                     : 2012:07:11 15:44:52+09:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 9.3.3 (Windows)
Format                          : application/pdf
Title                           : Microsoft Word - User_Manual_DWM-W051_r4_120711.doc
Creator                         : 29253
Document ID                     : uuid:087a2f62-abc8-439e-b431-1497ef49c972
Instance ID                     : uuid:29b11457-f23b-4d8c-bdf2-dd98f24da36b
Page Count                      : 7

EXIF Metadata provided by EXIF.tools