Mitsumi Electric Co DWMW095A 802.11 11abgn 2x2 MIMO+BT/BLE RADIO MODULE User Manual

Mitsumi Electric Co Ltd 802.11 11abgn 2x2 MIMO+BT/BLE RADIO MODULE

Contents

User Manual

Operating Manual FUJITSU Tablet STYLISTIC Q555 System
B5FK-5391-01ENZ0-00 Contact address in North America FUJITSU AMERICA INC. 1250 East Arques Avenue, Sunnyvale, CA 94085-3470, U.S.A. Telephone: 800 831 3183 or 408 746 6000 "http://solutions.us.fujitsu.com" "http://solutions.us.fujitsu.com/contact" Have a question? Email us at: "AskFujitsu@us.fujitsu.com" Copyright © 2014 Fujitsu Technology Solutions GmbH. All rights reserved
FUJITSU Tablet STYLISTIC Q555 Index 105 Operating Manual Fujitsu Contact Information Notational conventions Ports and controls Important notes First-time setup of your device Working with the Tablet PC Accessories for your Tablet PC (optional) Security functions Connecting external devices Settings in BIOS Setup Utility Troubleshooting and tips Technical data Manufacturer’s notes Appendix 7 8 9 11 15 19 40 54 61 65 68 77 83 89
Copyright and Trademark Information Fujitsu America, Incorporated has made every effort to ensure the accuracy and completeness of this document; however, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes. Fujitsu, the Fujitsu logo and STYLISTIC are registered trademarks of Fujitsu Limited or its subsidiaries in the United States and other countries. Intel and Intel Core are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. The ExpressCard word mark and logo are owned by the Personal Computer Memory Card International Association (PCMCIA) and any use of such marks by Fujitsu America, Incorporated is under license. Google is a trademark or registered trademark of Google Incorporated. Bluetooth is a trademark of Bluetooth SIG, Inc., USA. OmniPass is a trademark of Softex, Inc. Roxio is a trademark of Roxio, a division of Sonic Solutions. PowerDirector, PowerDVD, YouCam, and MakeDisc are trademarks of CyberLink Corp. Adobe, Acrobat, and Adobe Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. Made under license from DTS Licensing Limited. DTS and the symbol are registered trademarks and & DTS Boost is a trademark of DTS, Inc. Product contains software. © DTS, Inc. All rights reserved. The DVD player found in some models of the LIFEBOOK notebook incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights users. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. All other trademarks specified here are the property of their respective owners. DECLARATION OF CONFORMITYaccording to FCC Part 15Responsible Party Name:Address: Fujitsu America, Inc.1250 E. Arques AvenueTelephone:Declares that product:Sunnyvale, CA 94085(408) 746-6000Base Model Configuration: STYLISTIC Q555 Tablet PCComplies with Part 15 of the FCC Rules.This device complies with Part 15 of the FCC rules. Operations are subject to the following two conditions: (1) This device may not cause harmful interference, (2) This device must accept any interference received, including interference that may cause undesired operation.
Contents Contents Fujitsu Contact Information ........................................................................................................................ 7 Notational conventions ................................................................................................................................ 8 Ports and controls ........................................................................................................................................ 9 Important notes ........................................................................................................................................... 11 Safety instructions ......................................................................................................................................... 11 Additional safety notes for devices with wireless components ............................................................... 12 Protecting the display screen ...................................................................................................................... 12 Energy saving ................................................................................................................................................ 12 Energy saving under Windows ............................................................................................................. 12 Traveling with your Tablet PC ...................................................................................................................... 12 Before you travel .................................................................................................................................... 13 Transporting the Tablet PC ................................................................................................................... 14 Cleaning the Tablet PC ................................................................................................................................. 14 First-time setup of your device ................................................................................................................ 15 Unpacking and checking the device ........................................................................................................... 15 Choose a location ......................................................................................................................................... 16 Connecting the AC adapter ......................................................................................................................... 16 Switching on the device for the first time ................................................................................................... 17 Installing Bonus Apps ............................................................................................................................ 18 Working with the Tablet PC ...................................................................................................................... 19 Battery charging indicator ............................................................................................................................ 19 Switching the Tablet PC on .......................................................................................................................... 20 Programing the ON/OFF button ........................................................................................................... 20 Switching the Tablet PC off .......................................................................................................................... 21 Handwriting recognition ................................................................................................................................ 21 Touchscreen ............................................................................................................................................................ 22 Select display orientation (portrait or landscape format) ......................................................................... 23 Touch commands .......................................................................................................................................... 23 Calibrate the Dual Digitizer for finger-based operation of the device. ............................................. 23 Actions with one finger (Windows 8.1 Modern) ................................................................................. 24 Actions with one finger (Windows 8.1 Desktop) ................................................................................ 26 Actions with two fingers (Windows 8.1 Desktop) ............................................................................... 27 Using the stylus ............................................................................................................................................. 29 Stylus location ......................................................................................................................................... 30 Adjusting the stylus ................................................................................................................................ 30 Can the stylus tip be replaced? ............................................................................................................ 31 Calibrating the stylus ............................................................................................................................. 31 Installing a stylus tether ......................................................................................................................... 31 Tablet buttons ................................................................................................................................................. 32 Webcam .......................................................................................................................................................... 33 Rechargeable battery ................................................................................................................................... 33 Charging and maintaining the battery ................................................................................................. 33 Using the energy saving functions .............................................................................................................. 34 Memory cards ................................................................................................................................................ 35 Supported formats .................................................................................................................................. 35 Inserting the memory card .................................................................................................................... 35 Removing the memory card.................................................................................................................. 36 Fujitsu 3
Contents Wireless LAN/Bluetooth radio components........................................................................................ 38Switching the Wireless Components on and off................................................................................. 38Configuring WLAN access.................................................................................................................. 38Further information on WLAN and Bluetooth.......................................................................................38Ethernet and LAN (only with multifunctional cradle) ................................................................................... 39 GPS ................................................................................................................................................................. 39 Accessories for your Tablet PC (optional) ............................................................................................ 40 Your performance docking cradle (optional) ............................................................................................... 41 Cradle components ................................................................................................................................ 41 Setting up the cradle .............................................................................................................................. 42 Connecting the Tablet PC to the cradle ............................................................................................... 43 Disconnecting the Tablet PC from the cradle ..................................................................................... 44 Slice keyboard (optional) .............................................................................................................................. 45 Components of the keyboard cover ..................................................................................................... 45 Connecting the Tablet PC to the slice keyboard ................................................................................ 46 Separating the Tablet PC from the slice keyboard ............................................................................. 47 VESA mount (optional) ................................................................................................................................. 48 Hand strap (optional)..................................................................................................................................... 49 Shoulder strap (optional) .............................................................................................................................. 50 Folio case (optional) ...................................................................................................................................... 50 Micro USB adapters ...................................................................................................................................... 52 Security functions ....................................................................................................................................... 54 Configuring the fingerprint sensor ............................................................................................................... 54 Using the Security Lock ................................................................................................................................ 55 Configuring password protection in BIOS Setup Utility ............................................................................ 55 Protecting BIOS Setup Utility (supervisor password and user password) ...................................... 55 Password protection for booting the operating system ..................................................................... 56 Password protection for the hard disk ................................................................................................. 57 Smart Card reader (device dependent) ...................................................................................................... 59 Inserting the SmartCard ......................................................................................................................... 59 Trusted Platform Module - TPM (device dependent) ................................................................................ 60 Enabling TPM .......................................................................................................................................... 60 Disabling TPM ......................................................................................................................................... 60 Connecting external devices .................................................................................................................... 61 Connecting an external monitor................................................................................................................... 61 Micro HDMI port ...................................................................................................................................... 61 Display Port (performance docking cradle only)................................................................................. 62 VGA monitor port (multifunctional cradle only) ................................................................................... 62 Connecting USB devices .............................................................................................................................. 63 How to remove USB devices correctly ................................................................................................ 63 Connecting external audio devices ............................................................................................................. 64 Headphones port .................................................................................................................................... 64 Microphone port (performance docking cradle only) ......................................................................... 64 Settings in BIOS Setup Utility .................................................................................................................. 65 Starting the BIOS Setup Utility ..................................................................................................................... 65 4 Fujitsu
Contents BIOS Setup Utility operation ........................................................................................................................ 66 Exiting BIOS Setup Utility ............................................................................................................................. 67 Exit Saving Changes - save changes and exit BIOS Setup Utility .................................................. 67 Exit Discarding Changes - Reject changes and exit BIOS Setup Utility ......................................... 67 Load Setup Defaults – load default values ......................................................................................... 67 Discard Changes - Discard Changes without exiting BIOS Setup Utility ........................................ 67 Save Changes - save changes without exiting the BIOS Setup Utility ........................................... 67 Save changes and power off ................................................................................................................ 67 Troubleshooting and tips .......................................................................................................................... 68 Executing a reset........................................................................................................................................... 69 Forced shutdown .................................................................................................................................... 69 Execute a complete reset: Reset BIOS Setup to the standard values ........................................... 69 Help if problems occur .................................................................................................................................. 69 Recovering your Factory Image .................................................................................................................. 69 The Tablet PC’s date or time is incorrect ................................................................................................... 69 Battery indicator does not illuminate ........................................................................................................... 70 The Tablet PC’s touchscreen remains dark ............................................................................................... 70 The display on the Tablet PC’s touchscreen is difficult to read. .............................................................. 70 The external monitor remains blank ........................................................................................................... 71 The external monitor is blank or the image is unstable ........................................................................... 71 The cursor does not correctly follow the stylus movements .................................................................... 71 Stylus input not working ............................................................................................................................... 72 The Tablet PC does not start after switch on ............................................................................................ 72 The Tablet PC stops working ....................................................................................................................... 72 The printer does not print ............................................................................................................................. 72 The wireless connection to a network does not work .............................................................................. 73 The battery discharges too quickly ............................................................................................................. 73 Smart Card reader is not recognized ......................................................................................................... 73 SmartCard PIN forgotten .............................................................................................................................. 73 User and/or supervisor Smart Card lost ..................................................................................................... 74 SmartCard lost ............................................................................................................................................... 74 Acoustic warning ........................................................................................................................................... 74 Error messages on the screen .................................................................................................................... 75 Technical data .............................................................................................................................................. 77 Tablet PC ........................................................................................................................................................ 77 WLAN specifications ..................................................................................................................................... 79 Rechargeable battery ................................................................................................................................... 80 AC adapter (36 W) ........................................................................................................................................ 80 Multifunctional cradle (optional)................................................................................................................... 80 Slice keyboard (optional) .............................................................................................................................. 81 VESA mount (optional) ................................................................................................................................. 81 Hand strap (optional) .................................................................................................................................... 81 Shoulder strap (optional) .............................................................................................................................. 81 Folio case (optional)...................................................................................................................................... 82 Micro USB adapters (optional) .................................................................................................................... 82 Manufacturer’s notes ................................................................................................................................. 83 Disposal and recycling .................................................................................................................................. 83 Recycling your battery ........................................................................................................................... 83 DOC (Industry CANADA) Notices ............................................................................................................... 83 UL Notice ................................................................................................................................................. 84 ENERGY STAR Compliance ....................................................................................................................... 85 Fujitsu 5
Contents Declarations of conformity ............................................................................................................................ 85 FCC and IC Regulatory Information............................................................................................................ 85 Regulatory Notes and Statements ....................................................................................................... 86 Appendix ....................................................................................................................................................... 89 Before Using the Optional Wireless LAN ................................................................................................... 89 Wireless LAN Devices Covered by this Document ............................................................................ 89 Characteristics of the WLAN Device .................................................................................................... 89 Wireless LAN Modes Using this Device .............................................................................................. 89 Deactivating/Disconnecting the WLAN Device ................................................................................... 92 Configuring the Wireless LAN ...................................................................................................................... 92 Connection to the network ..................................................................................................................... 92 Troubleshooting the WLAN ................................................................................................................... 92 Using the Bluetooth Device .......................................................................................................................... 95 Image Backup and Recovery Procedures ................................................................................................. 95 Creating a Backup of Bootable Disk and Recovery Image ............................................................... 96 RECOVER YOUR SYSTEM WHEN THE HARD DRIVE IS STILL ACCESSIBLE ............................... 97 Using the Recovery and Utility Tools ................................................................................................................ 97 Restore the Recovery Image from Hidden Partition .......................................................................... 99 RECOVER YOUR SYSTEM WHEN THE HARD DRIVE IS NOT BOOTABLE ..................................100 Restore the Recovery Image for Full Hard Drive .............................................................................100 Recovering Your Recovery Image Using Recovery and Utility (for new hard drive or non-bootable hard drive) .....................................................................................................................101 Installing the Software after the Recovery Image is Restored .......................................................102 Index ............................................................................................................................................................. 105 6 Fujitsu
Fujitsu Contact Information Fujitsu Contact Information Service and Support You can contact Fujitsu Service and Support in the following ways: •Toll free phone: 1-800-8Fujitsu (1-800-838-5487)•Website: "http://solutions.us.fujitsu.com/www/content/support/contact/index.php"Before you place the call, have the following information ready so that the customer support representative can provide you with the fastest possible solution: •Product name•Product configuration number•Product serial number•Purchase date•Conditions under which the problem occurred•Any error messages that have occurred•Type of device connected, if anyFujitsu Shopping Online Please go to "http://www.shopfujitsu.com/store/ ". Maintaining Latest Configuration To ensure that you always have the most current driver updates related to your system, occasionally access the Fujitsu Software Download Manager (FSDM) utility. The FSDM utility is available from the Fujitsu Support site. FSDM will allow you to view a list of the most current drivers, utilities and applications to determine whether you have the latest versions. If you have a Windows 7 or or Windows 8/8.1 operating system, you will need to go to the Support Site to download the FSDM Utility: "http://support.fujitsupc.com/CS/Portal/support.do?srch=DOWNLOADS". Limited Warranty Your STYLISTIC Tablet PC is backed by a Fujitsu International Limited Warranty. Check the service kit that came with your Tablet PC for the Limited Warranty period and terms and conditions. Fujitsu 7
Notational conventions Notational conventions Pay particular attention to text marked with this symbol. Failure to observe this warning will endanger your life, will damage the device or lead to loss of data. The warranty will be invalidated if the device becomes defective through failure to observe these warnings. Indicates important information which is required to use the device properly. ► indicates an activity that must be performed 4 indicates a result This styleindicates data entered using the keyboard in a program dialogue or at the command line, e.g. your password (Name123) or a command used tostart a program (start.exe)This style indicates information that is displayed on the screen by a program, e.g.: Installation is complete. This style indicates •terms and texts used in a software interface, e.g.: Click on Save.•names of programs or files, e.g. Windows or setup.exe."This style" indicates •Cross-references to another section, e.g. "Safety information"•cross-references to an external source, e.g. a web address: For moreinformation, go to "http://solutions.us.fujitsu.com/"•names of CDs, DVDs and titles or designations of other materials, e.g.:"CD/DVD Drivers & Utilities" or "Safety/Regulations" manualKeyindicates a key on the keyboard, e.g: F10 This style indicates terms and text that are emphasized or highlighted, e.g.: Do not switch off the device 8 Fujitsu
Ports and controls Ports and controls This chapter presents the individual hardware components of your device. It gives an overview of the indicators and connections of the device. Please familiarize yourself with these items before you start to work with the device. Front 1 = DC input connector (DC IN) 2 = Micro HDMI port 3 = Headphone port 4 = SmartCard reader (device dependent) 5 = Storage card slot (protected by cover) 6 = Eyelet for stylus cord 7 = Speaker 8 = Security Lock device 6 1 2 3 4 5 4 1 2 3 4 5 6 7 8 1 = Ambient light sensor 2 = Webcam LED 3 = Webcam 4 = Guide for cradle or keyboard cover 5 = Docking port for cradle or slice keyboard 6 = Battery charging indicator Left-hand side Fujitsu 9
Ports and controls Right side 1 = Stylus holder 2 = Speaker 3 = Tether eyelet for stylus tether 4 = Shortcut button 5 = Decrease volume button Rear 6 = Increase volume button 7 = ON/OFF button 8 = USB port (USB 2.0) 9 = USB port (USB 3.0) 1 = Screw holes for mounting accessories 2 = Fingerprint sensor 3 = Webcam LED 4 = Camera light 5 = Webcam 1 5 4 1 1 1 2 3 4 5 6 7 8 9 3 2 1 10 Fujitsu
Important notes Important notes This chapter contains essential safety information which must be followed when working with your Tablet PC. The other notes provide useful information about your Tablet PC. Safety instructions Please follow the safety notes provided in the "Safety/Regulations" manual as well as the safety notes given below. Please pay special attention to the sections in the manual marked with the symbol on the left. When connecting and disconnecting cables, observe the relevant notes in this operating manual. Read the information on the ambient conditions in the "Technical data", Page 77 chapter and the information in the "First-time setup of your device", Page 15 chapter before preparing your Tablet PC for use and switching it on for the first time. When cleaning the device, please observe the relevant notes in the section "Cleaning the Tablet PC", Page 14. Pay attention to the additional safety notes for devices with wireless components provided in the "Safety/Regulations" manual. When handling this device, you come into contact with lead, a chemical which in California is held to be a possible cause of birth defects and other damage to fertility. Wash your hands after using the device. This Tablet PC complies with the relevant safety regulations for data processing equipment. If you have questions as to whether you can set up the Tablet PC in the intended environment, please contact your sales outlet or our hotline/service desk. Fujitsu 11
Important notes Additional safety notes for devices with wireless components If a wireless component (Wireless LAN, Bluetooth) is integrated in your Tablet PC, you must be sure to observe the following safety precautions when using your Tablet PC: •Switch off the wireless components when you are in an aircraft or driving in a car.•Switch off the wireless components when you are in a hospital, an operatingroom or near a medical electronics system. The transmitted radio waves canimpair the operation of medical devices.•Switch off the wireless components, when you let the device get near flammablegases or into hazardous environments (e.g. gas station, paint stores), as thetransmitted radio waves can cause an explosion or a fire.For further information on how to switch the wireless components on and off, refer to section "Switching the wireless components on and off", Page 38. Protecting the display screen Depending on your device configuration, where applicable your device is not waterproof. In this event, do not pour liquids onto the device and do not wash it with a wet cloth. Do not place items on the top of the display, or damage may occur. During normal use of the device, small particles from the environment can become embedded in the stylus tip and scratch the screen. The warranty does not cover a scratched screen. Energy saving If you will not be using your Tablet PC, switch it off. Switch off any connected external devices when they are not in use. If you use the energy-saving functions, the Tablet PC uses less power. If you do this, you will be able to work longer with the Tablet PC before having to recharge the battery. The energy efficiency is increased and environmental pollution is reduced. You save money and help protect the environment. Energy saving under Windows ►Make use of the available energy-saving functions as described in chapter"Using the energy saving functions", Page 34. Traveling with your Tablet PC Please follow the instructions below when traveling with your Tablet PC. 12 Fujitsu
Important notes Information on activating data encryption is provided in the documentation for your radio component. ►If you want to use your Tablet PC during a flight, ask the flight attendants to see if it is safe to use it.When traveling in other countries ►If you are traveling abroad, check that the AC adapter can be operated with thelocal AC voltage. If this is not the case, obtain the appropriate AC adapter for your Tablet PC. Do not use any other converter! ►Check whether the local AC voltage and the AC cable are compatible. If this is notthe case, buy an AC cable that suits the local conditions. ►Enquire with the appropriate government office of the country you will be travelling in as towhether you may operate the radio component integrated in your Tablet PC there. ►Take the necessary travel adapters with you when traveling abroad. Check in the followingtable for which travel adapters you will need, or ask your travel organizer. Before you travel ►Switch off the radio component for data security reasons. With data traffic via a wirelessconnection, it is also possible for unauthorized third parties to receive data. Power connection Travel destination United States, Canada, Mexico, parts of Latin America, Japan, Korea, Philippines, Taiwan Russia and the Commonwealth of Independent States (CIS), much of Europe, parts of Latin America, the Middle East, parts of Africa, Hong Kong, India, much of south-east Asia United Kingdom, Ireland, Malaya, Singapore, parts of Africa China, Australia, New Zealand Fujitsu 13
Important notes Transporting the Tablet PC Protect the Tablet PC from severe shocks and extreme temperatures (e.g. direct sunlight in a car). •Do not transport your Tablet PC while it is turned on.•Carry your Tablet PC with you while traveling. Do not check it in as baggage.•Never put your Tablet PC through a metal detector. Have it hand-inspected bysecurity personnel. You can however put your Tablet PC through a properlytuned X-ray machine. To avoid problems, place it close to the entrance ofthe machine and remove it as soon as possible or have it hand-inspected bysecurity personnel. Security officials may require you to turn your Tablet PCon. So make sure you have a charged battery on hand for this.►Switch the Tablet PC off.►Unplug the AC plug of the AC adapter and all external devices from the power outlets.►Disconnect the AC adapter cable and the data cables for all external devices.►To protect against damaging jolts and bumps, use a suitable Tablet PCcarrying case to transport your Tablet PC.Cleaning the Tablet PC Do not clean any interior parts yourself; leave this job to a service technician. Only use detergents designed for computers. Normal household cleaners and polishes can damage the labels on the keyboard and the Tablet PC, the paintwork or the Tablet PC itself. Ensure that no liquid enters the Tablet PC. The touchscreen is very sensitive to scratches! Only clean the display surface with a very soft, slightly damp cloth. ►Switch the Tablet PC off.►To prevent the device from being switched on unintentionally, remove the ACplug of the AC adapter from the power outlet.4 The surfaces may be cleaned with a dry cloth. If particularly dirty, use a cloth which has been moistened in mild domestic detergent and then carefully wrung out.14 Fujitsu
First-time setup of your device First-time setup of your device Please read the chapter "Important notes", Page 11. If your device is equipped with a Windows operating system, the necessary hardware drivers and supplied software are already pre-installed. Before switching it on for the first time, connect the device to the AC voltage using the AC adapter, see "Connecting the AC adapter", Page 16. The AC adapter must remain connected during the whole of the installation process. A system test is performed when your device is first switched on. Various messages can appear. The display may remain dark for a short time or may flicker. Please follow the instructions on the screen. NEVER switch off your device during the first-time setup process. The battery must be charged if you want to operate your device using the battery. When used on the move, the built-in battery provides the device with the necessary power. You can increase the operating time by using the available energy-saving functions. For instructions on how to connect external devices (e.g. mouse, printer) to your Tablet PC, please refer to the operating manual for your device. Unpacking and checking the device If you find that damage has occurred during transport, please notify your local sales outlet immediately! ►Unpack all the individual parts.►Check your device for any visible damage which may have occurred during transportation.You may need to reuse the packaging in the future, for example if you need to ship your device. Fujitsu 15
First-time setup of your device Choose a location Choose a suitable location for the device before setting it up. In doing so, please follow these instructions: •Never place the device or the AC adapter on a heat-sensitive surface.The surface could be damaged as a result. •Never place the device on a soft surface (e.g. carpeting, upholstered furniture,bed). This can result in damage caused by overheating. •The back of the device heats up during normal operation. Prolonged contactwith skin can become unpleasant or even result in burns. •Place the device on a stable, flat, non-slippery surface. Please note that therubber feet of the device may mark certain types of delicate surfaces. •Keep other objects at least 100 mm / 4 inches away from the deviceand its AC adapter to ensure adequate ventilation. •Do not expose the device to extreme environmental conditions. Protectthe device against dust, humidity and heat. Connecting the AC adapter Observe the safety notes in the enclosed "Safety/Regulations" manual. The supplied AC cable conforms to the requirements of the country in which you purchased your device. Make sure that the AC cable is approved for use in the country in which you intend to use it. ►Connect the AC cable (1) to the AC adapter.►Plug the AC cable (2) into a power outlet.►Connect the AC adapter cable (3) to theDC jack (DC IN) of the device.3 2 1 16 Fujitsu
First-time setup of your device Switching on the device for the first time To make it easier to use your device for the first time, the operating system is pre-installed on the hard disk. 1 ►Press the ON/OFF button (1) for about one second to switch the device on.►During the installation process, follow the on-screen instructions.You can find information and help on the Windows operating system functions on the Internet at "http://windows.microsoft.com". If a Windows 8.1 operating system is installed on your Tablet PC, a tutorial is automatically started when a new user logs on for the first time, which shows you how to use the new functions of Windows 8.1. Fujitsu 17
First-time setup of your device Installing Bonus Apps After you have started your system the first time, you will see a Bonus Apps icon on your desktop. ►Click on the icon to see which additional applications are available for you to install.4 Applications that are already installed appear in grey, those that are available for installation appear in blue. ►Select the applications you wish to install by selecting the checkbox adjacent to your selection.or ►Click Select All if you would like to install all available applications.►To confirm your selection, click Install.Note that in some cases (depending upon which application was selected for installation) after installation completes, the system will prompt you to reboot. There are also cases in which if multiple applications are selected to install but one of them needs a reboot, the system will reboot and continue installing the rest of the selected applications. 18 Fujitsu
Working with the Tablet PC 1 Please refer to the notes in the chapter "Important notes", Page 11. Battery charging indicator The battery charging indicator (1) gives information about the status of the power supply. Working with the Tablet PC This chapter describes the basics for operating your Tablet PC. You can find instructions on how to connect external devices (e.g. mouse, flash storage) to the Tablet PC in the chapter "Connecting external devices", Page 61. Status / color Description On (red) The battery is being charged. Off The Tablet PC is switched off or in Save-to-Disk mode. Fujitsu 19
Working with the Tablet PC 1 ►Press the ON/OFF button (1) for about one second to switch the device on.Programing the ON/OFF button You can program the ON/OFF button: If you have assigned a password, you must enter this when requested to do so, in order to start the operating system. Detailed information can be found in the chapter "Security functions", Page 54. Switching the Tablet PC on Operating system Menu Windows 8.1 Windows 8.1 Desktop - Control Panel - Hardware and Sound - Power Options 20 Fujitsu
Working with the Tablet PC Switching the Tablet PC off Back up your data and close all applications before you switch off your device. Otherwise data might be lost. ►Shut down the operating system correctly.or►Press the ON/OFF button for < 2 seconds to switch into connected standby mode.or ►Press the ON/OFF button for > 2 seconds to < 10 seconds to display the"Sweep downwards to switch off" popup.or ►If the Tablet PC is not switched off automatically, press the ON/OFF buttonfor about 10 seconds (forced shutdown).Handwriting recognition For detailed information on handwriting recognition, see the documentation for your operating system. Under Windows 8.1 you can set the required language under Control Panel – Time, Language and Region – Language. Fujitsu 21
Working with the Tablet PC Touchscreen High-quality LCD screens (TFT) are installed in Fujitsu Tablet PCs. For technical reasons, these screens are manufactured for a specific resolution. An optimal, clear picture can only be ensured in the resolution intended for the particular screen. A screen resolution which differs from the specification can result in an unclear picture. The screen resolution of your Tablet PC’s touchscreen is optimally set at the factory. Current production technology cannot guarantee an absolutely fault-free screen display. A few isolated constantly lit or unlit pixels (picture elements) may be present. The maximum permitted number of such faulty pixels is specified in the international standard ISO 9241-307 (Class II). Example: A screen with a resolution of 1280 x 800 has 1280 x 800 = 1024000 pixels. Each pixel consists of three subpixels (red, green and blue), so there are almost 3 million subpixels in total. According to ISO 9241-307 (class II), a maximum of 2 light and 2 dark pixels and in addition 5 light or 10 dark subpixels or an equivalent mix (1 light subpixel counts as 2 dark subpixels) are allowed to be defective. Pixel A pixel consists of 3 subpixels, normally red, green and blue. A pixel is the smallest element that can be generated by complete functionality of the display. Subpixel A subpixel is a separately addressable internal structure within a pixel that enhances the pixel function. Cluster A cluster contains two or more defective pixels or subpixels in a 5 x 5 pixel block. Background lighting LCD screens are operated with background lighting. The luminosity of the background lighting can decrease over the period of use of the Tablet PC. However, you can set the brightness of your screen yourself. Ambient light sensor If your Tablet PC was shipped with the Windows operating system, the screen brightness is regulated by means of the ambient light sensor and depending on the respective light conditions. This results in optimum readability and longer battery life at the same time. If your Tablet PC was shipped with Windows 8.1, the adaptive brightness setting is deactivated. To change the ambient light sensor settings, select Control Panel - System and Security - Power Options - Change plan settings - Change advanced power settings - Display - Activate adaptive brightness setting.. Select On to activate the adaptive brightness setting with the help of the ambient light sensor. Synchronizing the display on the touchscreen and an external monitor In Windows 8.1 wipe your finger over the screen from the right-hand edge. The setting Charms - Devices - Second monitor opens. Select the desired output type. You can also use the Fujitsu Display Manager in the Windows Mobility Center to set the output type. 22 Fujitsu
Working with the Tablet PC Select display orientation (portrait or landscape format) You can choose to use either portrait or landscape format for the display. Windows 8.1 You can change these settings under Windows 8.1 Desktop - Control Panel - Hardware and Sound - Windows Mobility Center / Rotate screen. To switch off the automatic changing between portrait and landscape format, select Control Panel - Appearance and Personalization - Display - Screen Resolution. In the Fujitsu Tablet Controls settings, profiles are saved for operation with different screen orientations. These profiles have preset standard configurations that can be modified as desired. These settings do not just affect the monitor settings on the Tablet PC, but also on external monitors that are connected. Touch commands You can execute certain commands by using your finger tip on the touchscreen of your device. Alternatively, everything which you can select or activate using your finger tip can also be selected or activated using the stylus. Calibrate the Dual Digitizer for finger-based operation of the device. If Windows 8.1 is installed on your Tablet PC, your Tablet PC is already calibrated at initial setup. If a different operating system is installed on your Tablet PC, you must calibrate it with your fingers before first use, so that it recognizes your fingertips as accurately as possible. As soon as you ascertain that the accuracy is deteriorating, you must recalibrate the device. Operating system Menu Windows 8.1 Desktop To calibrate, run the Hardware and Sound / Tablet PC Settings function in the Control Panel. You need to calibrate both portrait and landscape formats. Fujitsu 23
Working with the Tablet PC Actions with one finger (Windows 8.1 Modern) Action Description Wipe your finger over the screen from the right-hand edge. ►Open Charms with system commands(equivalent to pressing the Windows button +C button).►Working with the mouse: Position the mousepointer at the bottom right-hand edge of thescreen.Wipe your finger over the screen from the left-hand edge. ►Switch between the most recently usedapplications (equivalent to pressing theWindows button + Ctrl + Space).►Working with the mouse: Position the mousepointer at the bottom left-hand edge of thescreen.Wipe your finger over the screen from the top or bottom edge. ►Open the App commands (equivalent topressing the Windows button + Z button).Wipe from the top to the bottom of the screento dock or close the current App.►Working with the mouse: Right-click on theApp to display the App commands.24 Fujitsu
Working with the Tablet PC Action Description Press and hold ►Keep your finger pressed on an object on thescreen to display a menu with further options.►Working with the mouse: Move the mousepointer over the object to display a menu withfurther options.Tap on an object ►Tap your finger on an object on the screento open an App or a link or to execute acommand.►Working with the mouse: Left-click on theobject.Scroll / Move object / Swivel object ►Use this function to scroll through lists orwebsites or to swivel or move an object.►Working with the mouse: Left-click on theobject, keep the mouse button pressed andmove / swivel the object or scroll.Fujitsu 25
Working with the Tablet PC Actions with one finger (Windows 8.1 Desktop) Action Description Selecting objects (click with the left mouse button) ►Tap once briefly with the finger on the object.Starting programs (double-click with the left mouse button) ►Use one finger to tap twice in quicksuccession on the program symbol.Moving objects/windows (while holding the left mouse button pressed, drag & drop) ►Place your finger on the object/window,keep your fingertip pressed against thetouchscreen and move the desiredobject/window.Opening a context menu (click with the right mouse button) ►Tap your finger on the desired item.Keep your fingertip pressed against thetouchscreen.The context menu appears.Moving the cursor ►Position one finger on the touchscreen andmove your fingers in the desired direction.26 Fujitsu
Working with the Tablet PC Actions with two fingers (Windows 8.1 Desktop) Action Description Scrolling ►Place two fingers on the touchscreen.►Move the fingers up to scroll up.or ►Move the fingers down to scroll down.Rotating ►Position your thumb on the touchscreen androtate the image clockwise or anticlockwiseusing your index finger.Fujitsu 27
Working with the Tablet PC Action Description Increase or decrease zoom ►Put two fingers on the touchscreen andmove them apart to increase the size of thezoom.or ►Put two fingers on the touchscreen andmove them together to decrease the sizeof the zoom/view.Lock context-sensitive menus ►Use two fingers to tap twice in quicksuccession on the touchscreen.28 Fujitsu
Working with the Tablet PC Using the stylus 1 = stylus tip 2 = stylus button (right mouse button) 3 = eyelet for stylus tether You can use the stylus on your Tablet PC as an electronic writing tool, to select menu items and to navigate through the programs. Programs that support handwriting recognition also allow you to write directly on the screen with the stylus. You can also use the stylus as a drawing tool. The Tablet PC is supplied with a stylus tether which you can attach to the eyelets on the stylus and on the Tablet PC. Use only the stylus that was provided with your Tablet PC. Do not use any other pointed object as a substitute, that was not specially designed for your Tablet PC. Replace the stylus tip if it is worn. The warranty does not cover a scratched screen. While writing, take care that you do not scratch the surface of the display (e.g. with a wristwatch or bracelet). The stylus of the Tablet PC is an electronic instrument that can be damaged if used improperly. Handle the stylus with care. Our recommendations for proper handling of the stylus are as follows: •Do not gesture with the stylus.•Do not use the stylus as a pointer.•Do not use the stylus on surfaces other than the screen of the Tablet PC.•Do not try to turn the grip of the stylus. The grip is used to put thestylus into its slot and to take it out of its slot.•Never store the stylus with its weight on the tip (e.g. with the tip down in a styluscontainer). If the stylus is stored with the tip pointing down, this may have anadverse effect on the stylus mechanism (particularly under high temperatures). Inthis case the stylus tip may react as though it is constantly being pressed down. To avoid damage, the stylus should be stored in the stylus slot when not in use.The stylus can be influenced by electromagnetic fields (cursor quivers or jumps). There may be a few areas on the screen where the cursor quivers slightly in spite of pressing the stylus down firmly. The screen responds to entries made with the tip of the finger or the stylus when the tip of the finger or the stylus directly touches the screen. You can use the stylus to perform almost all functions for which you would otherwise use a mouse. 3 2 1 Fujitsu 29
Working with the Tablet PC 1 Stylus location On delivery, the stylus is located in the stylus garage: Adjusting the stylusDelete functions are not supported by the stylus. Action Mouse Stylus Selecting menu items Click with the left mouse button. Tap on the menu entry with the tip of the stylus. Starting programs Double-click with the left mouse button. Tap on the program symbol twice in rapid succession using the stylus tip. Moving an object or window Drag with the left mouse button pressed. Place the stylus tip directly on the object or window. Keep the stylus tip held against the screen. Drag the desired object or window. Opening a context menu Click with the right mouse button. Tap on the desired element with the stylus and keep the stylus pressed against the screen. Moving the cursor Move the mouse Place the tip of the stylus directly on the screen. Operating system Menu Windows 8.1 Under Windows 8.1 Desktop - Control Panel - Hardware and Sound - Pen and Touch Input you can make various settings for the stylus (assignment and function of the stylus button). 30 Fujitsu
Working with the Tablet PC You should also always repeat the calibration if the co-ordination between the stylus and the cursor movement deteriorates. Installing a stylus tether Attach the stylus with a stylus tether to prevent accidentally dropping it or losing it. You device has one eyelet on the left side and one eyelet on the right side for securing the stylus tether (see "Ports and controls", Page 9). The tether eyelet on the right side is shown below. Calibrating the stylus If Windows 8.1 is installed on your Tablet PC, your Tablet PC is already calibrated at initial setup. If a different operating system is installed on your Tablet PC, you must calibrate it with the stylus before first use, so that it recognizes the stylus as accurately as possible. Operating system Menu Windows 8.1 Desktop To calibrate, run the Hardware and Sound / Tablet PC Settings function in the Control Panel. You need to calibrate both portrait and landscape formats. ►Fasten the stylus tether to the stylus eyelet and to the eyelet on the Tablet PC.Can the stylus tip be replaced?Fujitsu 31
Working with the Tablet PC Tablet buttons Your Tablet PC is fitted with three tablet buttons. Symbol Description Functions + Volume + button Increase volume –Volume - buttonDecrease the volume – – – Shortcut button Call the status area by pressing or start a screenshot function by a long press (depends on configuration) 32 Fujitsu
Working with the Tablet PC Webcam Your device has two webcams: one on the front of the device and one on the rear. The webcam has its own status indicator. The indicator lights up when the webcam is active. Depending on the software used, you can use your webcam to take pictures, record video clips or take part in web chats. •The picture quality depends on the lighting conditions and the software being used.•You can only operate the webcam with a particular application (e.g. an Internet telephonyprogram or a video conferencing program which supports a webcam).•When using the webcam the support of the Tablet PC must not wobble.•The webcam automatically adjusts itself to the current light level. For this reason,the touchscreen may flicker while the light level is adjusted.Further information on use of the webcam and additional settings for your webcam can be found in the help function of the program using the webcam. Rechargeable battery The built-in battery provides the Tablet PC with the necessary power for use on the move. You can increase the service life of the battery by caring for the battery properly. The average battery service life is around 500 charge/discharge cycles. You can extend the battery service life by taking advantage of the available energy-saving functions. Charging and maintaining the battery The Tablet PC battery can only be charged when the ambient temperature is between 5°C / 41 °F and max. 35°C / 95°F. You can charge the battery by connecting the Tablet PC to the AC adapter (see "Connecting the AC adapter", Page 16). If the battery is running low you will hear a warning alarm. If you do not connect the AC adapter within five minutes of hearing the warning alarm, your Tablet PC will switch off automatically. Monitoring the battery state of charge A battery symbol for monitoring the battery capacity is displayed in the system bar / status indicator. The battery symbol shows you the battery charge. Fujitsu 33
Working with the Tablet PC Using the energy saving functions The Tablet PC uses less power when the power management features are enabled. You will then be able to work longer when using the battery before having to recharge it. The energy efficiency is increased and environmental pollution is reduced. By choosing the best power options, you can make significant savings and at the same time help protect the environment. We recommend the following settings: Function Operating on AC power Operating on battery power Turn off display After 10 minutes After 5 minutes Turn off hard disk(s) After 15 minutes After 10 minutes Energy saving After 20 minutes After 15 minutes ►Set the energy saving functions in your Control Panel.►Set the screen saver in your Control Panel.or ►Keep a finger pressed on the desktop to display the context menu. Configure the screensaver under Change screen saver.If you need further information about an option, you can get help with most settings by pressing the ? symbol in the upper right of the screen to open the Microsoft Help.When the Tablet PC is in an energy saving mode, you must remember the following: When the Tablet PC is in energy saving mode, open data is held in main memory or in a swap file on the hard disk. Never switch off the Tablet PC while it is in an energy saving mode. If the built-in battery is nearly drained, close all open files and do not go into energy saving mode. If you do not intend to use your Tablet PC for a long period of time: ►Exit the energy saving mode if necessary via touching the screen or by switching on theTablet PC. ►Close all opened programs and completely shut down the Tablet PC.34 Fujitsu
Working with the Tablet PC Memory cards Your Tablet PC is equipped with an integrated storage card reader. Use storage cards to enlarge the storage of your Tablet PC. a 2 1 Follow the manufacturer’s instructions when handling the memory cards.Supported formats It supports the following formats: •Micro Secure Digital (SDTM Card)•Micro SDHC•Micro SDXCInserting the memory card ►Open the slot cover (1).►Carefully push the memory card into the slot (a) in the direction of the arrow (2) until youfeel the memory card engage. The label area must be facing downward. Do not applyany force, otherwise the delicate contact surfaces could be damaged.►Close the slot cover.Fujitsu 35
Working with the Tablet PC Removing the memory card To avoid any loss of data, always follow the correct procedure for removing the card (see the documentation for your operating system). ►Open the slot cover.a 1 2 3 ►Press the edge of the memory card so that the memory card jumps slightly out of the slot (1).►Pull the memory card out of the slot (a) in the direction of the arrow (2).►Close the slot cover (3).36 Fujitsu
Working with the Tablet PC This page intentionally left blank Fujitsu 37
Working with the Tablet PC Wireless LAN/Bluetooth radio components The installation of radio components not approved by Fujitsu will invalidate the certifications issued for this device. Switching the wireless components on and off The wireless components are switched on and off using the appropriate functions of the operating system. ►To switch wireless components on and off individually, select Settings – ChangePC settings – Network – Airplane mode. Configuring WLAN access •Requirement: A WLAN is available and you have the necessary access data to hand.Information on configuring WLAN access can be found in the documentation for your operating system. Further information on WLAN and Bluetooth For further information about WLAN or Bluetooth, please refer to the appendix of this Operating Manual. For WLAN specifications, see chapter "WLAN specifications", Page 79. 38 Fujitsu
Working with the Tablet PC 1 2 Ethernet and LAN (only with multifunctional cradle) The internal network module of your Tablet PC supports Ethernet LAN. You can use it to establish a connection to a local network (LAN = Local Area Network). ►Connect the network cable to the LANport of the cradle (1). ►Connect the network cable to yournetwork connection (2). Your network administrator can help you to configure and use the LAN connections. The network cable is not included in the delivery scope. This type of cable can be obtained from a specialist dealer. GPS Whether your device has this function depends on the chosen equipment level.Fujitsu 39
Accessories for your Tablet PC (optional) Accessories for your Tablet PC (optional) •Multifunctional cradle for charging the Tablet PC and with additional ports•Slice keyboard•VESA mounting attachment•Shoulder strap•Folio case•Micro USB adapter (cables)The following sections provide more information on handling the accessories. The following accessories are available for your Tablet PC: ### unanswered, which accessories are available in addition to the cradle and keyboard ### 40 Fujitsu
Accessories for your Tablet PC (optional) Your performance docking cradle (optional) As well as fast charging, your multifunctional cradle is a device that also allows you to quickly connect your Tablet PC to your peripherals such as a monitor, keyboard, mouse, etc. You only need to dock the Tablet PC to be able to work with your peripheral devices. Cradle components 1 5 6 7 8 2 3 4 9 10 11 12 1 2 3 4 5 6 = Slide-out button = Connector on the cradle for the docking port of the Tablet PC = USB port 2.0 = USB port 2.0 = USB port 2.0 = Headphone port 7 = Microphone port 8 = VGA monitor port 9 = Display Port 10 = LAN port 11 = Security Lock device 12 = DC jack socket (DC IN) Fujitsu 41
Accessories for your Tablet PC (optional) Setting up the cradle Select a suitable location for the cradle before setting it up. In doing so, please follow these instructions: •Place the cradle on a flat, stable, non-slippery surface.•Never place the cradle or the AC adapter on a heat-sensitive surface.•Do not expose the cradle to extreme environmental conditions.Protect the cradle from dust, moisture and heat.42 Fujitsu
Accessories for your Tablet PC (optional) Connecting the Tablet PC to the cradle It is possible to connect the Tablet PC to the cradle while it is running. To prevent problems, we recommend that you switch the Tablet PC off first. Disconnect the AC adapter from the Tablet PC before connecting the Tablet PC to the cradle. When the Tablet PC is connected to the cradle, you must connect the AC adapter to the cradle. ►Switch the Tablet PC off.►Remove the AC plug of the AC adapter from the power outlet.►Remove the AC adapter cable from the DC jack (DC IN) of the Tablet PC.►Position the Tablet PC so that it lies against the storage surface of the cradle.►Push the Tablet PC on to the cradle in the direction of the arrow (1) untilyou feel it engage on the connector.►Plug the AC adapter cable into the DC jack (DC IN) on the cradle (2).►Connect the AC cable to the AC adapter (3).►Plug the AC cable into the power outlet (4).2 1 4 3 Fujitsu 43
Accessories for your Tablet PC (optional) Disconnecting the Tablet PC from the cradle It is possible to separate the Tablet PC from the cradle while it is running. However, to prevent any problems, we recommend that you switch the Tablet PC off first or that you execute the appropriate undocking function provided by the operating system. ►Switch the Tablet PC off.2 1 ►Keep the slide-out button pressed (1).►While holding down the lower part of the cradle, lift the Tablet PC off thecradle in the direction of the arrow (2).44 Fujitsu
Accessories for your Tablet PC (optional) Slice keyboard (optional) The slice keyboard is an optimized device for the convenient input of text. It only needs to be docked with the Tablet PC. Components of the keyboard cover 1 2 3 1 = Release button 2 = Docking port for the Tablet PC 3 = Status indicators (Num Lock, Caps Lock, Scroll Lock) Fujitsu 45
Accessories for your Tablet PC (optional) Connecting the Tablet PC to the slice keyboard 1 2 ►Press the slide-out button (1) until it remains in the pressed position (red marking visible).►Push the Tablet PC onto the keyboard cover in the direction of the arrowuntil you feel it engage in the connector (2).46 Fujitsu
Accessories for your Tablet PC (optional) Separating the Tablet PC from the slice keyboard 1 2 ►Keep the unlocking button pressed (1).►Lift the Tablet PC away from the slice keyboard in the direction of the arrow (2).Fujitsu 47
Accessories for your Tablet PC (optional) VESA mount (optional) Use the VESA mount to secure the Tablet PC to a hand strap (optional) or to a monitor with the appropriate screw holes. 1 1 1 1 3 3 2 3 3 •Use the appropriate tool of the correct size when securing the screws.•Keep the screws out of the reach of children.►Remove the screws (1).►Position the VESA mount on the Tablet PC (2). Make sure that the screw holes of theVESA mount and of the Tablet PC lie exactly on top of each other.►Secure the VESA mount using the screws (3).unfinished.... Graphics still show predecessor K39948 Fujitsu
Accessories for your Tablet PC (optional) Hand strap (optional) •Use the appropriate tool of the correct size when securing the screws.•Keep the screws out of the reach of children.•Do not shake the device too much when you are holding it on thehand strap, otherwise it may fall down.►Position the hand strap on the Tablet PC (1). Make sure that the screw holes of thehand strap and of the Tablet PC lie exactly on top of each other.►Secure the hand strap with the screws (2).2 2 1 unfinished.... Graphics still show predecessor K399Fujitsu 49
Accessories for your Tablet PC (optional) 1 1 3 2 3 2 unfinished.... Graphics still show predecessor K399 Shoulder strap (optional) • Use the appropriate tool of the correct size when securing the screws. • Keep the screws and mountings out of the reach of children. • To prevent damaging the screws, do not use a motorized screwdriver. ► Remove the screws (1). ► Position the fittings (2). ► Secure the fittings using the screws (3). ► Secure the shoulder strap to the fittings. Folio case (optional) unfinished.... Graphics still show predecessor K399 50 Fujitsu
Accessories for your Tablet PC (optional) •The folio case contains magnets. Keep away from objects that may beeasily affected by the influence of magnetism.•LCD may be accidently turned on if the cover is not properly closed.•Make sure the unit is firmly fitted into the folio case fasteners so it will not fall out.•This folio case is only designed to contain and carry this unit.Do not use it for any other purpose.•Do not put the folio case in direct sunlight or expose it to high temperature or humidity.►Position the Tablet PC on the folio case as shown.►Engage the top edge and then press it down.The following illustration shows you the many ways in which the folio case can be used: Fujitsu 51
Accessories for your Tablet PC (optional) Micro USB adapters 5 USB adapters are available for the device: Micro USB to USB adapter Micro USB to HDMI adapter Micro USB to VGA adapter unclear whether or not this is applies to this device52 Fujitsu
Accessories for your Tablet PC (optional) For technical specifications, see chapter"Micro USB adapters (optional)", Page 82.Micro USB to Display Port adapter Micro USB to LAN adapter Fujitsu 53
Security functions Security functions Your Tablet PC has several security features that you can use to secure your system and your personal data from unauthorized access. This chapter explains how to use these functions, and what the benefits are. ►Install the fingerprint software to be able to use the fingerprint sensor (1).1 Please remember that in some cases, for example, forgetting your password, you may be locked out of the system and unable to access your data. Therefore, please note the following information: •Back up your data on external data carriers at regular intervals.•Some security functions need you to choose passwords. Make a noteof the passwords and keep them in a safe place.If you forget your passwords you will need to contact our Service Desk. Deletion or resetting of passwords are not covered by your warranty and a charge will be made for assistance. Configuring the fingerprint sensor The fingerprint sensor can record the image of a fingerprint. With additional fingerprint software, this image can be processed and used instead of a password. 54 Fujitsu
Security functions Using the Security Lock Your device comes with a Security Lock device for the Kensington Lock Cable. With the Kensington Lock Cable, a sturdy steel cable, you can protect your device and the port replicator against theft. The Kensington Lock Cable is available as an accessory. ► Fit the Kensington Lock Cable to the corresponding mechanism on your device. Configuring password protection in BIOS Setup Utility Before using the various options for password protection in the BIOS Setup Utility, please proceed as follows to increase data security: Make a note of the passwords and keep them in a safe place. If you forget your supervisor password you will not be able to access your Tablet PC. Passwords are not covered by your warranty and a charge will be made for assistance. Your password can be up to eight characters long and can contain letters and numbers. No distinction is made between uppercase and lowercase. Protecting BIOS Setup Utility (supervisor password and user password) If you have opened these operating instructions on the screen, we recommend that you print them out. You cannot call up the instructions on the screen while you are setting up the password. The supervisor password and the user password both prevent unauthorized use of the BIOS Setup Utility. The supervisor password allows you to access all of the functions of the BIOS Setup Utility, while the user password will only give you access to some of the functions. You can only set up a user password if a supervisor password has already been assigned. Calling and using the BIOS Setup Utility is described in the chapter "Settings in BIOS Setup Utility", Page 65. Fujitsu 55
Security functions Assigning the supervisor and user passwords ►Start the BIOS Setup Utility and go to the Security menu.►Select the Set Supervisor Password field and press the Enter key.4 With Enter new Password: you are asked to enter a password.►Enter the password and press the Enter key. 4 Confirm new Password requires you to confirm the password.►Enter the password again and press the Enter key. 4 Changes have been saved is displayed as a confirmation that the new password has been saved.►To set the user password, select Set User Password and proceed exactly aswhen configuring the supervisor password. 4 If you do not want to change any other settings, you can exit BIOS Setup Utility.►In the Exit menu, select the option Save Changes & Exit.►Select Yes and press the Enter key. 4 The Tablet PC is rebooted and the new password is effective. It will now be necessary to first enter your supervisor or user password in order to open the BIOS Setup Utility. Pleasenote that the user password only provides access to a few of the BIOS settings.Changing the supervisor password or user password You can only change the supervisor password when you have logged into the BIOS Setup Utility with the supervisor password. ►Start the BIOS Setup Utility and go to the Security menu.►When changing the password, proceed exactly as when assigning a password.Removing passwords To remove a password (without setting a new password) perform the following steps: ►Start the BIOS Setup Utility and go to the Security menu.►Highlight the Set Supervisor Password or Set User Password field and press the Enter key. 4 You will be requested to enter the current password by the Enter Current Password prompt.Enter New Password will appear and you will be requested to enter a new password.►Press the Enter key twice at this request.►In the Exit menu, select the option Save Changes & Exit.►Select Yes and press the Enter key. 4 The Tablet PC is rebooted and the password is removed.Removing the supervisor password simultaneously deactivates the user password.Password protection for booting the operating system With the supervisor password you have set in the BIOS Setup Utility (see section "Assigning the supervisor and user passwords", Page 56), you can also prevent booting of the operating system. 56 Fujitsu
Security functions Activating system protection ►Start the BIOS Setup Utility and go to the Security menu.►Select the Password on Boot option and press the Enter key. ►Select the option you require (Disabled, First Boot or Every Boot) and press the enter key►Select the Save Changes & Exit option under Exit.4 The Tablet PC reboots. You will be prompted to enter your password (the supervisor password). Deactivating system protection ►Start the BIOS Setup Utility and go to the Security menu.►Select the Password on Boot option and press the Enter key. ►Select the Disabled option and press the Enter key. 4 If you do not want to change any other settings, you can exit BIOS Setup Utility.►Select the Save Changes & Exit option under Exit.4 The Tablet PC reboots. The system is no longer password-protected.Password protection for the hard disk The hard disk password prevents unauthorized access to the hard disk drives and is checked internally each time the system is booted. The condition for this is that you have assigned at least the supervisor HDD password. Activating hard disk protection ►Call up the BIOS Setup and select the Security menu.4 If you have not assigned BIOS passwords yet, define the supervisor and the userpassword now, if desired (see "Security functions", Page 54). ►Mark the Hard Disk Security field and press the Enter key. ►In the area Drive0, mark the field Set Master Password and press the Enter key. 4 Enter new Password then appears and you are asked to enter a password.►Enter the password and press the Enter key. 4 Confirm new Password requires you to confirm the password.►Enter the password again and press the Enter key. 4 With Setup Notice: Changes have been saved you receive confirmation thatthe new password has been saved. ►If you wish to enter a password for a second hard disk (Drive1), in the areaDrive1 mark the field Set Master Password and proceed in exactly the same way as for the set up of the first hard disk (Drive0). 4 The field Password Entry on Boot is set to Enabled by default. You can exit the BIOSSetup once you have finished changing the settings. ►From the Exit menu, choose the option Exit Saving Changes.►Press the Enter key and select Yes. 4 The Tablet PC reboots and your hard disk is now protected with a password. Thepassword prompt is enabled as soon as the Tablet PC has rebooted.Fujitsu 57
Security functions Deactivating hard disk protection To cancel a password (without setting a new password) proceed as follows: ►Call up the BIOS Setup and select the Security menu.►Mark the Hard Disk Security field and press the Enter key. ►In the area Drive0, mark the field Set Master Password and press the Enter key. 4 With the prompt Enter current Password you are first asked to enter the old password again. With Enter new Password you are then prompted to enter a new password.►After the request, press the Enter key three times.►From the Exit menu, choose the option Exit Saving Changes.►Press the Enter key and select Yes. 4 The Tablet PC reboots and there is no longer any password protection for this hard disk. ►If you wish to remove a password for a second hard disk (Drive1), in the areaDrive1 mark the field Set Master Password and proceed in exactly the same way as for the removal of the first hard disk (Drive0). 58 Fujitsu
Security functions Smart Card reader (device dependent) SmartCards are not supplied as standard equipment. You can use all SmartCards that comply with the ISO standard 7816-1, -2 or -3. These SmartCards are available from various manufacturers. With the appropriate software you can use your SmartCard as an alternative to password protection, but also as a digital signature, for encrypting your e-mails or for home banking. We recommend that you always use two SmartCards. Always keep one of the SmartCards in a safe place if you are carrying the other SmartCard with you. In order to be able to take advantage of all the security features of your Tablet PC, you will need a CardOS SmartCard from Fujitsu. The SmartCard can only be used with a PIN, so maximum protection is maintained even when the SmartCard is lost. In order to maximize your security, the CardOS SmartCard is disabled if three incorrect attempts are made to enter the PIN. During first time use of your CardOS SmartCard, you must either enter the preset PIN "12345678" or the PIN which has been notified to you by your system administrator. Inserting the SmartCard Do not use force when inserting and removing the SmartCard. Make sure that foreign objects do not fall into the SmartCard reader. ► Turn the Tablet PC over. ► Slide the Smart Card carefully into the Smart Card reader (a) in the direction of the arrow (1), with the chip facing upward. a 1 Fujitsu 59
Security functions Trusted Platform Module - TPM (device dependent) To use the TPM, you must enable the TPM in the BIOS Setup before the software is installed. The requirement for this is that you have assigned at least the supervisor HDD password (see "Security functions", Page 54). Enabling TPM •Requirement: You have assigned a supervisor password (see "Security functions", Page 54).►Call BIOS Setup and select the Security menu.►Mark the TPM Security Chip Setting field and press the Enter key.►Select the entry Enabled to enable the TPM4 Once you have enabled the TPM the Clear Security Chip menu item appears.You can clear the holder in the TPM using Clear Security Chip. With Enabled,all secret keys (e.g. SRK - Storage Root Keys, AIK - Attestation Identity Keysetc.) generated by applications are deleted.Take note that you can then no longer access the data you haveencrypted on the holder-based keys!►Select the Exit Saving Changes option in the Exit menu.►Press the Enter key and select Yes. 4 The Tablet PC restarts and the TPM is enabled after the reboot. Disabling TPM •Requirement: You have assigned a supervisor password (see "Security functions", Page 54).►Call BIOS Setup and select the Security menu.►Mark the TPM Security Chip Setting field and press the Enter key.►Select the entry Disabled to disable the TPM.►From the Exit menu, choose the option Exit Saving Changes.►Press the Enter key and select Yes. 4 The Tablet PC is rebooted and the TPM is disabled.60 Fujitsu
Connecting external devices Connecting external devices Under all circumstances, please observe the safety notes provided in the "Important notes", Page 11 chapter before connecting or disconnecting any devices to or from your Tablet PC. Always read the documentation supplied with the device you wish to connect. Never connect or disconnect cables during a thunderstorm. Never pull at a cable when disconnecting it. Always grasp the plug. Follow the order described below when you connect external devices to the Tablet PC or separate them from it: With some devices, such as USB devices, it is not necessary to switch off the Tablet PC and the device before connecting/disconnecting. For more information about whether or not devices need to be switched off, please refer to the documentation supplied with your external device. Some of the external devices require special drivers (see the operating system and external device documentation). Connecting an external monitor Micro HDMI port The micro HDMI port on your device can be used to connect an external amplifier, LCD TV or a plasma TV with an HDMI connection. ►Connect the data cable to theexternal device.►Connect the data cable to the microHDMI port.Some LCD televisions have only two speakers/speaker ports and therefore cannot reproduce Dolby Digital or DTS. To play back HDMI sound, you must change the HDMI sound settings accordingly. You can find the settings under Control Panel - Hardware and Sound. Deactivate the settings for DTS Audio and Dolby Digital to enable playback of HDMI sound. Fujitsu 61
Connecting external devices Display Port (performance docking cradle only) The Display Port of the performance docking cradle can be used to connect a monitor, an LCD TV or a plasma TV with a corresponding connection. You can also switch back and forth between the external monitor and the LCD screen of the Tablet PC, see "Touchscreen", Page 22. You can display the same image on the external monitor and on the LCD screen of the Tablet PC at the same time. ► Connect the data cable to the external device. ► Connect the data cable to the Display Port of the cradle. Some LCD televisions have only two speaker connections and therefore cannot reproduce Dolby Digital or DTS. In order to reproduce the sound, you must go into Windows and adjust the sound settings. ► To do this, deactivate the DTS Audio and Dolby Digital settings in the control panel for the Realtek HDMI Output. VGA monitor port (multifunctional cradle only) An analog monitor is connected to the analog VGA monitor port. Screen output is limited to a maximum of two screens at the same time. ► Switch off the Tablet PC and the external monitor. ► Plug the data cable of the external monitor into the monitor port. ► First switch on the external monitor and then switch on the Tablet PC. 62 Fujitsu
Connecting external devices Connecting USB devices On the USB ports you can connect external devices that also have a USB port (e.g. a DVD drive, a printer, a scanner or a modem). USB devices are hot-pluggable. This means you can connect and disconnect the cables of USB devices while the operating system is running. USB 1.x has a maximum data transfer rate of 12 Mbps. USB 2.0 has a data transfer rate of up to 480 Mbps. USB 3.0 has a data transfer rate of up to 5 Gbps. Additional information can be found in the documentation for the USB devices. ►Connect the data cable to theexternal device.►Connect the data cable to a USB porton the Tablet PC or cradle.Device drivers USB devices will be automatically recognized and installed by your operating system. How to remove USB devices correctly Always correctly remove the device according to the rules described below, to ensure that none of your data is lost. ►Tap the symbol for safe removal of the hardware.►Select the device you wish to shut down and remove.►Tap OK.4 Wait for the dialog box which tells you that it is now safe to remove the device. Fujitsu 63
Connecting external devices Connecting external audio devices Headphones port You can connect either headphones or external speakers to your Tablet PC via the headphone port. ►Connect the audio cable to theexternal device. ►Connect the audio cable to the headphone port of the Tablet PC. 4 The internal speakers are disabled.If you buy a cable from a retailer, please note the following information: The headphone port on your Tablet PC is a "3.5 mm jack socket". If you want to connect headphones or speakers you will need a "3.5 mm jack plug". Microphone port (performance docking cradle only) The microphone port of the performance docking cradle allows you to connect an external microphone, a MiniDisc player, MP3 player, CD player or a tape deck to your Tablet PC. ►Connect the audio cable to theexternal device. ►Connect the audio cable to the microphone port of the performance docking cradle. 64 Fujitsu
Settings in BIOS Setup Utility Settings in BIOS Setup Utility To navigate more easily in the BIOS Setup Utility, you can use an external USB keyboard, or keep the volume button pressed during the boot process. The BIOS Setup Utility allows you to set the system functions and the hardware configuration for the Tablet PC. When the Tablet PC is delivered, the default settings are effective. You can change these settings in the menus of the BIOS Setup Utility. Any changes you make take effect as soon as you save and exit the BIOS Setup Utility. The BIOS Setup Utility program contains the following menus: About Displays information relating to the BIOS, processor and Tablet PC System Advanced system settings Advanced Configuration of various hardware components, such as mouse, keyboard, processor Security Password settings and security functions Boot Configuration of the start-up sequence Exit Exits the BIOS Setup Utility Starting the BIOS Setup Utility ►Keep the "Lock screen orientation" tablet button pressed and switch the Tablet PC on.►If a password has been assigned, enter the password and press the Enter key. If you have forgotten the password, contact your system administrator or contact our customer service centre. The BIOS Setup Utility starts. Fujitsu 65
Settings in BIOS Setup Utility → BIOS Setup Utility operation Press the F1 key to display help about operation of the BIOS Setup Utility. The description of the individual settings is shown in the right-hand window of the BIOS Setup Utility. With the key you can load the default settings of the BIOS Setup Utility. ►Use the cursor keysor to select the menu you wish to access to make changes. 4 The menu is displayed on the screen. ►Select the option you want to change with the cursor keys►Press the "Enter" key. or ↓ . ►Press the key to exit the selected menu. ►For future reference, make a note of the changes you have made (for example, in this manual).F9 ← ↑ ESC 66 Fujitsu
Settings in BIOS Setup Utility Exiting BIOS Setup Utility You need to select the desired option in the Exit menu and activate it by pressing the Enter key: Exit Saving Changes - save changes and exit BIOS Setup Utility ► To save the current menu settings and exit the BIOS Setup Utility, select Exit Saving Changes and Yes. 4 The Tablet PC is rebooted and the new settings come into effect. Exit Discarding Changes - Reject changes and exit BIOS Setup Utility ► To discard the changes, select Exit Discarding Changes and Yes. 4 The settings which were valid when BIOS Setup Utility was called remain effective. The BIOS Setup Utility ends and the Tablet PC is rebooted. Load Setup Defaults – load default values ► To copy the standard entries for all menus of the BIOS Setup Utility, choose Load Setup Defaults and Yes. Discard Changes - Discard Changes without exiting BIOS Setup Utility ► To discard the changes you have made, select Discard Changes and Yes. 4 The settings in place when BIOS Setup Utility was called remain effective. You can now make additional settings in the BIOS Setup Utility. ► If you want to exit the BIOS Setup Utility with these settings, select Exit Saving Changes and Yes. Save Changes - save changes without exiting the BIOS Setup Utility ► To save the changes, select Save Changes and Yes. 4 The changes are saved. You can now make additional settings in the BIOS Setup Utility. ► If you want to exit BIOS Setup Utility with these settings, choose Exit Saving Changes and Yes. Save changes and power off ► To save the changes and switch off your device, select Save Changes and Power Off and Yes. 4 The changes are saved. Your device is shut down. Fujitsu 67
Troubleshooting and tips Troubleshooting and tips If a fault occurs, try to correct it as described. If you fail to correct the problem, proceed as follows: ► Make a note of the steps and the circumstances that led to the fault. Also make a note of any error messages displayed. ► Switch the Tablet PC off. ► Please contact the Hotline/Service Desk. You can contact Fujitsu Service and Support in the following ways: • Toll free phone: 1-800-Fujitsu (1-800-838-5487) • Website: "http://solutions.us.fujitsu.com/www/content/support/contact/index.php" Before you place the call, have the following information ready so that the customer support representative can provide you with the fastest possible solution: • The model name and serial number of the Tablet PC. The serial number is located on a sticker on the underside of the Tablet PC. • Notes with the messages that appeared on the screen and information on acoustic signals. • All changes you have made to the hardware or software after receiving the Tablet PC. • All changes you have made to the BIOS Setup settings after receiving the Tablet PC. • Your system configuration and all peripheral devices connected to your system. • Your sales contract. Our Tablet PCs have been designed primarily with mobile applications in mind. This means that considerable effort has been made to optimize components and equipment in terms of weight, space and energy requirements. Depending on the particular configuration you have purchased, it is possible that functionality may be slightly reduced compared to a desktop PC if you are running processor-intensive gaming software, e.g. games with intensive 3D graphics. Updating your hardware with drivers which have not been approved by Fujitsu may result in performance losses, data losses or malfunction of the equipment. A list of approved drivers and current BIOS versions can be downloaded from: "http://solutions.us.fujitsu.com" 68 Fujitsu
Troubleshooting and tips Executing a reset If the device no longer responds to your inputs, choose one of the following options: Forced shutdown ► Press and hold the ON/OFF button for at least 10 seconds. 4 The device will be shut down. You can then restart it. Execute a complete reset: Reset BIOS Setup to the standard values ► Shut down the device. ► If the device does not respond, you may have to force the shutdown, as described above. ► Press the ON/OFF button, the increase volume button and the Windows button simultaneously for at least 2 seconds. 4 The device will restart when you release the buttons. Help if problems occur Should you encounter a problem with your computer that you cannot resolve yourself: ► Note the ID number of your device. The ID number is found on the type rating plate on the back or underside of the casing. ► For further clarification of the problem, contact the Fujitsu Service Desk. When you do this, please have ready the ID number and serial number of your system. Recovering your Factory Image In the event you need to restore your original Factory Image, please refer to the appendix of this Operating Manual. The Tablet PC’s date or time is incorrect tery Cause Troubleshooting Time and date are incorrect. ► With the BIOS-Setup-Utility, you can set the date and time in the Main menu. Date and time are still set incorrectly after switching on the Tablet PC. ► Please contact your sales outlet or our hotline/service desk. Fujitsu 69
Troubleshooting and tips The Tablet PC’s touchscreen remains darkThe display on the Tablet PC’s touchscreen is difficult to read. Battery indicator does not illuminate Cause Troubleshooting The battery is discharged. ►Charge the battery.or ►Connect the Tablet PC to a power outletusing the AC adapter.Cause Troubleshooting Touchscreen is switched off. ►Press a key (external keyboard) or tap onthe touchscreen.External monitor or television set connected. ►Check whether the graphics driver settingsare correct or whether an external monitorhas been detected in "Intel Graphics MediaAccelerator Driver for mobile".Cause Troubleshooting Reflected glare ►Move the Tablet PC into a different position.►Increase the brightness of the screen.70 Fujitsu
Troubleshooting and tips The external monitor remains blank Cause Troubleshooting Monitor is switched off. ► Switch the external monitor on. Power saving has been activated (monitor is blank). ► Press a key (external keyboard) or tap on the touchscreen. Brightness is set to dark. ► Adjust the brightness of the monitor. Screen output is set to the Tablet PC touchscreen. ► Check whether the graphics driver settings are correct or whether an external monitor has been detected in "Intel Graphics Media Accelerator Driver for mobile". The external monitor’s AC cable or data cable is not connected properly. ► Switch off the Tablet PC and the external monitor. ► Check whether the AC cable is plugged properly into the external monitor and into the power outlet. ► Check that the data cable is properly connected to the Tablet PC and the external monitor (if it is plugged in with a connector). ► Switch on the external monitor and the Tablet PC. The external monitor is blank or the image is unstable Cause Troubleshooting The wrong external monitor has been selected or the wrong screen resolution has been set for the application program. ► Terminate the application program in Windows. If the error persists after terminating the program, use the key combination for switching the screen output in order to switch to the touchscreen of the Tablet PC. Change the following setting: ► Set the screen resolution: Set the screen resolution as described in the documentation for your operating system. ► Select monitor: Select monitor 1 or 2 as described in the documentation for your operating system. The cursor does not correctly follow the stylus movements Cause Troubleshooting Stylus incorrectly calibrated. ► Calibrate the stylus as described in chapters "Adjusting the stylus", Page 30 and "Calibrating the stylus", Page 31. Fujitsu 71
Troubleshooting and tips The Tablet PC stops workingThe printer does not printStylus input not working Cause Troubleshooting Incorrect driver installed. ►Reinstall the driver for the "dual digitizer".The Tablet PC does not start after switch on Cause Troubleshooting The battery is dead. ►Charge the battery.or ►Connect the AC adapter to the TabletPC.The AC adapter is not connected properly. ►Check whether the AC adapter is properlyconnected to the Tablet PC.►Switch the Tablet PC on.Cause Troubleshooting The Tablet PC is in energy saving mode. ►End energy saving mode.An application program has caused the malfunction. ►Close the application program or restartthe Tablet PC (by restarting the operatingsystem or switching the device off and backon again).The battery is dead. ►Charge the battery.or ►Connect the AC adapter to the TabletPC.Cause Troubleshooting The printer is not switched on. ►Make sure that the printer is switchedon and ready for operation (refer to thedocumentation supplied with the printer).The printer is not connected correctly. ►Check that the data cable between the TabletPC and the printer is properly connected.The printer driver is faulty or not correctly installed, or it is the wrong printer driver. ►Check that the data cable between the TabletPC and the printer is properly connected.►Check whether the correct printer driver isloaded (refer to the printer documentation).72 Fujitsu
Troubleshooting and tips The battery discharges too quicklySmart Card reader is not recognizedThe wireless connection to a network does not work Cause Troubleshooting The wireless component is switched off. ►Switch the wireless component on (see"Switching the wireless components on andoff", Page 38). The wireless component is switched on. Despite this, the wireless connection to a network does not work. ►Check whether the wireless connection isenabled by the software.►Further information on using the wirelesscomponent can be found in the help files. Cause Troubleshooting The battery is either too hot or too cold. In this case the battery indicator flashes. ►Bring the Tablet PC up/down to a normaloperating temperature again.►If the operating time of the battery life isextremely short, the battery is probably tooold. Replace the battery if necessary.You may have an application running that consumes a great deal of power due to frequent accessing of the hard disk or optical drive. ►Use the AC adapter whenever possible.The maximum brightness may have been set for the screen. ►Reduce the brightness of the screen tolower energy consumption: You will find thesetting under Control Panel – Hardware andSounds – Windows Mobility Center.Cause Troubleshooting Smart Card inserted incorrectly. ►Make sure you have inserted your SmartCard into the Smart Card reader withthe chip facing upwards / downwards(device-dependent).►Check whether the Smart Card you areusing is supported. Your Smart Card mustcomply with the ISO standard 7816-1, -2,-3 and -4.SmartCard PIN forgotten Cause Troubleshooting PIN forgotten ►If you work in a network, contact yoursystem administrator, who can unlock yourTablet PC using a supervisor PIN.Fujitsu 73
Troubleshooting and tips SmartCard lost Acoustic warning User and/or supervisor Smart Card lost Cause Troubleshooting User and/or supervisor Smart Card lost ►If you have lost your user Smart Card, youcan continue working with the supervisorSmart Card and initialize a new user SmartCard or deactivate the SystemLock function.►If you have lost the supervisor Smart Card,you can also continue working, but you nolonger have all rights and cannot initializeanother supervisor Smart Card.►If you have lost both Smart Cards, youcannot boot your system. Please contact ourcustomer service center. You must provideproof of ownership for the device. Thecustomer service center will then refer youto our service partner, who will unlock yourdevice (for a charge).Cause Troubleshooting SmartCard lost. ►If you work in a network, contact yoursystem administrator, who can boot yourTablet PC with a supervisor SmartCard.Cause Troubleshooting A beep sounds every few seconds. The battery is almost dead. ►Charge the battery.74 Fujitsu
Troubleshooting and tips If the error message appears repeatedly despite troubleshooting measures, contact the place of purchase or our customer service center. Error messages on the screen This section describes the error messages generated by the BIOS Setup. Error messages displayed by the operating system or programs are described in the documentation for these programs. Error message/cause Troubleshooting CMOS Battery Bad If the error message occurs repeatedly, the buffer battery in the Tablet PC is flat. ►Contact your sales outlet or our customerservice center.System CMOS checksum bad - Default configuration used The system configuration information is incorrect. ►Switch the Tablet PC off.►Switch the Tablet PC on.►Keep the volume button and the shortcutbutton pressed and switch the Tablet PCon. If you keep the volume button pressedduring the boot process, you can switch intothe BIOS Setup-►In the BIOS Setup, select the Exit menu.►Select the entry Load Setup Defaults.►Select OK and press the Enter key. Extended memory failed at offset: xxxx Failing Bits: zzzz zzzz When testing the extended memory. an error has resulted at the address xxxx. ►Contact your sales outlet or our customerservice center.Failure Fixed Disk n The settings of the hard disk drive are incorrect. ►Start the BIOS Setup (Primary Mastersubmenu) and select the correct settings.Keyboard controller error ►Switch your Tablet PC off with the ON/OFFbutton.►Wait 3 - 5 seconds and switch the Tablet PCon again.Keyboard error If you use an external keyboard: ►Check the connection and reboot the Tablet PC. nn Stuck key ►Make sure that no key is pressed.Operating system not found ►Check in the BIOS Setup whether your harddisk has been set correctly.►Make sure that the operating system isinstalled on the corresponding drive.Press <F1> to resume, <F2> to SETUP This error message appears if an error occurs during the self-test before starting the operating system. ►Press the Alt tablet button to boot theoperating systemFujitsu 75
Troubleshooting and tips Error message/cause Troubleshooting Real time clock error ►Contact your sales outlet or our customerservice center.nnnnK Shadow RAM failed at offset: xxxx Failing Bits: zzzz ►Contact your sales outlet or our customerservice center.System battery is dead - Replace and run SETUP ►Contact your sales outlet or our customerservice center.System cache error - Cache disabled ►Contact your sales outlet or our customerservice center.System timer error ►Contact your sales outlet or our customerservice center.76 Fujitsu
Technical data Technical data Tablet PC General Processor Intel® BayTrail-T™ SoC, Quad Core Intel® Atom™ Processor Z3770 (2.4 GHz) Main memory (SO DIMM) 4GB DiMM onboard Electrical data Safety regulations complied with CE Protection class II Maximum power consumption (when the Tablet PC is switched on, connected to the slice keyboard and the battery is charged): 36 W Touchscreen Size 10.1" WQXGA Wide View TFT Screen resolution 2560 x 1600 pixels/16 million colors Pixel class II Brightness control 12 levels Technology Wide-View High-Bright Display with LED background lighting Digitizer and glass panel Dual digitizer with Glare touchscreen Cameras •Front: HD camera•Back: 8 megapixels, autofocus, mobile lightGraphics card Chip Intel® HD graphics Maximum resolution of external display: 1920 x 1080 (1080p) Dimensions Width x Depth x Height 10.51 in. x 7.12 in. x 0.51 in. (267.0 x 180.8 x 9.9 mm / 16.0 mm) (depending on the back shell) Weight depending on configuration from 1.31 lbs. (640 g) Input devices Tablet buttons 3 keys Stylus Active stylus with a pressure button Slots Storage card slot 1 x micro SD Card Ports Headphones port 3.5 mm stereo mini jack Docking port 1 x from predecessor Q584. Request for input.Fujitsu 77
Technical data USB (Universal Serial Bus) 1 x USB 3.0, 1 x micro USB 2.0 Ambient conditions Environment class DIN IEC 721 7K1 Mechanism class DIN IEC 721 7M2 Operating temperature 5 °C .... 35 °C / 41 °F .... 95 °F Transport temperature (2K2) –15 °C .... 60 °C / 5 °F .... 140 °F 78 Fujitsu
Technical data WLAN specifications Type of network Integrated Dual-Band Wireless-N 7260 device conforms to IEEE 802.11a, 802.11b/g, and 802.11n, Wi-Fi based*. Transfer rate (Automatic switching) IEEE802.11 a and g: 54 Mbps max. data rate; IEEE802.11n: 300 Mbps max. data rate Active frequency • 802.11n: 2.4 GHz or 5 GHz • 802.11b/g: 2400~2473 MHz • 802.11a: 4900~5850 MHz Typical operating distances** • 802.11a: 40 ft. (12 m) @ 54 Mbps; 300 ft. (91 m) @ 6 Mbps • 802.11b: 100 ft. (30 m) @ 11 Mbps; 300 ft. (91 m) @ 1 Mbps • 802.11g: 100 ft. (30 m) @ 54 Mbps; 300 ft. (91 m) @ 1 Mbps • 802.11n: Estimated double the operating distance of 802.11g and 802.11a in their respective frequencies Number of channels • 802.11a: 8 independent channels • 802.11b/g: 11 channels, 3 non-overlapping channels • 802.11n: Channel bonding takes two of the non-overlapping 20MHz channels and combines it into one 40MHz channel. It is actually 12 non-overlapping channels with channel bonding and 24 without. Also it is 1 non-overlapping channel in 2.4GHz when channel bonding is used. Security Encryption types: compatible with WEP, TKIP, AES***, WPA 1.0 and WPA 2.0 Encryption key, lengths supported: 64 bits and 128 bits Maximum recommended number of computers to be connected over wireless LAN (during ad hoc connection) 10 units or less **** * “Wi-Fi based” indicates that the interconnectivity test of the organization which guarantees the interconnectivity of wireless LANs (Wi-Fi Alliance) was passed. ** The operating distances given above increase or decrease depending on factors such as the number of walls, reflecting material or interference by external RF sources. *** Network key encryption (WEP) occurs with the number of bits given above, after deduction of the fixed length of 24 bits the user may however also set 40 or 104 bits. **** Depending on the particular practical application, the number of computers which can be networked is reduced if necessary. Fujitsu 79
Technical data AC adapter (36 W) An additional AC adapter or AC cable can be ordered at any time. Multifunctional cradle (optional) Rechargeable battery For information on the batteries used in your device, please see "http://solutions.us.fujitsu.com/www/content/support/". 3-cell lithium polymer battery 9900 mAh Rated voltage 3.8 V Rated capacity 38 Wh Rated voltage 12 V Max. rated current 3 A Electrical data Safety regulations complied with CE Protection class II Ports Headphone port 3.5 mm stereo mini jack Microphone port 3.5 mm stereo mini jack Docking port 40-pin Display Port 1 x VGA monitor port 1 x USB (Universal Serial Bus) 3 x USB 2.0 LAN port 1 x Security Lock device 1 x Ambient conditions Environment class DIN IEC 721 7K1 Mechanism class DIN IEC 721 7M2 Operating temperature 5 °C .... 35 °C / 41 °F .... 95 °F Temperature in transit –15 °C .... 60 °C / 5 °F .... 140 °F 80 Fujitsu
Technical data VESA mount (optional) Hand strap (optional) Shoulder strap (optional) Slice keyboard (optional) Electrical data Safety regulations complied with CE Protection class II Ports Docking port 40-pin Touchpad Yes Ambient conditions Environment class DIN IEC 721 7K1 Mechanism class DIN IEC 721 7M2 Operating temperature 5 °C .... 35 °C / 41 °F .... 95 °F Temperature in transit –15 °C .... 60 °C / 5 °F .... 140 °F Dimensions Width x Depth x Height 9.06 in. x 5.43 in. x 0.56 in. (230 x 138 x 14.1 mm) Weight 0.198 lbs. (90 g) Dimensions Width x Depth x Height 478 mm x 77 mm x 13 mm / 18.8 in. x 3.03 in. x 0.51 in. Weight Approx. 24 g / 0.053 lbs. Dimensions Width x Depth x Height 49.80 in. x 0.98 in. x 0.189 in. (1265 mm x 25 mm x 4.8 mm) Weight Approx. 0.074 lbs. (33.4 g) Fujitsu 81
Technical data Micro USB adapters (optional) Folio case (optional) Dimensions Width x Depth x Height 460 mm x 273 mm x 16 mm / 18.11" x 10.75" x 0.63" Weight Approx. 0.86 lbs. (390 g) Adapter Length Max. resolution Micro USB to USB adapter 6 inches N/A Micro USB to HDMI adapter 6 inches 1920 x 1080 Micro USB to VGA adapter 6 inches 1920 x 1080 Micro USB to Display Port adapter 6 inches 1920 x 1080 Micro USB to LAN adapter 6 inches N/A 82 Fujitsu
Manufacturer’s notes Manufacturer’s notes Disposal and recycling You can find information on this subject on your Tablet PC or on our website ("http://solutions.us.fujitsu.com/www/content/products/trade-in_program/"). Recycling your battery Over time, the batteries that run your mobile computer will begin to hold a charge for a shorter amount of time; this is a natural occurrence for all batteries. When this occurs, you may want to replace the battery with a fresh one*. If you replace it, it is important that you dispose of the old battery properly because batteries contain materials that could cause environmental damage if disposed of improperly. Fujitsu is very concerned with environmental protection, and has enlisted the services of the Rechargeable Battery Recycling Corporation (RBRC)**, a nonprofit public service organization dedicated to protecting our environment by recycling old batteries at no cost to you. RBRC has drop-off points at tens of thousands of locations throughout the United States and Canada. To find the location nearest you, go to "www.RBRC.org" or call 1-800-822-8837. If there are no convenient RBRC locations near you, you can also go to the EIA Consumer Education Initiative website "http://EIAE.org/ " and search for a convenient disposal location. Remember – protecting the environment is a cooperative effort, and we must make every effort to protect it for current and future generations. * To order a new battery for your Fujitsu mobile computer, go to the Fujitsu shopping site at "www.shopfujitsu.com" in the US or "www.fujitsu.ca/products/notebooks" in Canada. ** RBRC is an independent third party to which Fujitsu provides funding for battery recycling; RBRC is in no way affiliated with Fujitsu. DOC (Industry CANADA) Notices Radios and Television This Class B digital apparatus meets all requirements of Canadian Interference-Causing Equipment Regulations. CET appareil numérique de la class B respecte toutes les exigence du Réglement sur le matérial brouilleur du Canada. Fujitsu 83
Manufacturer’s notes UL Notice IMPORTANT SAFETY INSTRUCTIONS This unit requires an AC adapter to operate. Only use UL Listed I.T.E. adapters with an output rating of 12 VDC, with a minimum current of 3.0A (65W). The correct output rating is indicated on the AC adapter label. Refer to the illustration below for the correct AC adapter output polarity: When using your notebook equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: •Do not use this product near water for example, near a bathtub, washbowl, kitchensink or laundry tub, in a wet basement or near a swimming pool. •Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in afire. They may explode. Check with local codes for possible special disposal instructions. SAVE THESE INSTRUCTIONS For Authorized Repair Technicians Only CAUTION: For continued protection against risk of fire, replace only with the same type and rating fuse. WARNING: Danger of explosion if Lithium (CMOS) battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instruction. 84 Fujitsu
Manufacturer’s notes ENERGY STAR Compliance Your Fujitsu system is an ENERGY STAR qualified mobile PC. By choosing a computer with the latest energy-saving technology, you’re helping to preserve our environment for future generations. ENERGY STAR is a joint program of the U.S. Environmental Protection Agency, U.S. Department of Energy, Natural Resources Canada, and other governments around the world helping us save money while protecting the environment through energy efficient products and practices. With energy costs and global warming top-of-mind for consumers, Fujitsu is committed to offering solutions that help consumers conserve energy and improve the quality of our environment. Sleep mode: You will notice that your computer is initially set so that the display turns off after 15 minutes of user inactivity, and the computer goes into Sleep mode after 20 minutes of user inactivity. When going into Sleep mode, the computer also reduces the speed of any active Ethernet network links. To “wake” the computer from Sleep mode, press the Suspend/Resume Button. Energy saving benefits: Fujitsu ENERGY STAR qualified mobile PCs use about half as much electricity as standard equipment – saving half in utility costs. But more than that, ENERGY STAR also makes a difference for the environment. Did you know that the average house can be responsible for twice the greenhouse gas emissions as the average car? That’s because every time you flip on a light switch, run your dishwasher, or turn on your PC, you use energy, which means more greenhouse gas emissions from power plants. So the more energy we can save through energy efficiency, the more we help to reduce greenhouse gases and the risks of global warming. To learn more about the important ENERGY STAR program, visit:"www.energystar.gov". To read about how Fujitsu is supporting Sustainable Management along with several other environmental activities, visit the Fujitsu Corporate Citizenship page at: "http://www.computers.us.fujitsu.com/www/content/aboutus/environmental/environment.php". FCC and IC Regulatory Information Please note the following regulatory information related to the wireless LAN device. Fujitsu 85
Manufacturer’s notes Regulatory Notes and Statements Wireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions, however, are far much less than the electromagnetic energy emissions from wireless devices such as mobile phones. Wireless LAN devices are safe for use by consumers because they operate within the guidelines found in radio frequency safety standards and recommendations. The use of Wireless LAN devices may be restricted in some situations or environments, such as: •On board an airplane, or•In an explosive environment, or•In situations where the interference risk to other devices or services isperceived or identified as harmful.In cases in which the policy regarding use of Wireless LAN devices in specific environments is not clear (e.g., airports, hospitals, chemical/oil/gas industrial plants, private buildings), obtain authorization to use these devices prior to operating the equipment. Regulatory Information/Disclaimers Installation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, or the substitution or attachment of connecting cables and equipment other than those specified by the manufacturer. It is the responsibility of the user to correct any interference caused by such unauthorized modification, substitution or attachment. The manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failure to comply with these guidelines. This device must not be co-located or operated in conjunction with any other antenna or transmitter. For IEEE 802.11a Wireless LAN: For operation within 5.15~5.25 GHz frequency range, it is restricted to indoor environments, and the antenna of this device must be integral. Federal Communications Commission and Industry Canada statement: This device complies with Part 15 of FCC Rules and Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and, (2) This device must accept any interference, including interference that may cause undesired operation of this device. Déclaration d’Industrie Canada Cet appareil est conforme à la Section 15 des Règles de la FC C et à la ( aux) norme(s) RSS concernant les appareils exempt s de licence par Industrie Canada. Son fonctionnement est soumis aux deux condition s suivantes : (1) cet appareil ne doit pas causer d’interférence nuisib le; (2) cet appareil doit accepter toutes les interférences reçues, y compris celles pouvan t causer un mauvais fonctionnement de l’appareil. 86 Fujitsu
Manufacturer’s notes FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: 1.Reorient or relocate the receiving antenna.2.Increase the distance between the equipment and the receiver.3.Connect the equipment to an outlet on a circuit different from the one the receiver is connected to.4.Consult the dealer or an experienced radio/TV technician for help.FCC Radio Frequency Exposure statement The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure to low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposure have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. The wireless LAN radio device has been tested and found to comply with FCC radiation exposure limits set forth for an uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg, and 1.6W/kg by Industry Canada. This device is compliant with SAR for general population /uncontrolled exposure limits in ANSI/IEEE C95.1-1992 and Canada RSS 102, and had been tested in accordance with the measurement methods and procedures specified in OET Bulletin 65 Supplement C, and Canada RSS 102. This device has been tested, and meets the FCC, IC RF exposure guidelines when tested with the device operating conditions. Déclaration de la FCC/d’Industrie Canada sur l’exposition aux radiofréquences La norme régissant l’exposition des appareils sans fil aux radiofréquences emploie une unité de mesure dénommée Taux d’absorption spécifique, ou TAS. La FCC et Industrie Canada ont défini la même limite de TAS : 1,6 W/kg. Cet appareil est conforme au TAS pour les limites d’exposition générales de la population/non contrôlées définies par les règles C95.1-1992 de l’ANSI/IEEE et RSS 102 d’Industrie Canada ; il a été testé en conformité avec les méthodes et procédures de mesure spécifiées dans le supplément C du bulletin 65 de l’OET (Office d’ingénierie et de technologie) et la règle RSS 102 d’Industrie Canada. Cet appareil a été testé selon les directives de la FCC et d’IC concernant l’exposition aux radiofréquences et s’est révélé conforme à ces dernières lorsqu’il a été testé en contact direct avec le corps. Fujitsu 87
Manufacturer’s notes Export restrictions This product or software contains encryption code which may not be exported or transferred from the US or Canada without an approved US Department of Commerce export license. This device complies with Part 15 of FCC Rules., as well as ICES 003 B / NMB 003 B. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. Modifications not expressly authorized by Fujitsu America, Inc. may invalidate the user’s right to operate this equipment. Canadian Notice The device for the 5150 - 5250 MHz band is only for indoor usage to reduce the potential for harmful interference to co-channel mobile satellite systems. The maximum antenna gain of 6 dBi permitted (for devices in the 5250 - 5350 MHz, 5470 - 5725 MHz and 5725 - 5825 MHz bands) to comply with the e.i.r.p. limit as stated in A9.2 of RSS210. In addition, users are cautioned to take note that high power radars are allocated as primary users (meaning they have priority) of 5250 - 5350 MHz and 5650 - 5850 MHz and these radars could cause interference and/or damage to LE-LAN devices. Avis pour le Canada Le matériel destiné à un usage sur la bande 5 150 - 5 250 MHz doit être utilisé uniquement à l’intérieur afin de réduire les risques de brouillage nuisible causé aux systèmes mobiles par satellite fonctionnant sur un même canal. Un gain d’antenne de 6 dBi est autorisé (pour le matériel utilisant les bandes 5 250 - 5 350 MHz, 5 470 - 5 725 MHz et 5 725 - 5 825 MHz), conformément à la limite p.i.r.e. maximale permise selon l’annexe A9.2 afférent aux périphériques RSS210. En outre, les utilisateurs doivent prendre garde au fait que les radars de grande puissance sont considérés comme des utilisateurs principaux (ce qui signifie qu’ils sont prioritaires) des bandes 5 250 - 5 350 MHz et 5 650 - 5 850 MHz et qu’ils pourraient causer des interférences et/ou des dommages aux appareils de réseau exempts de licence. 88 Fujitsu
Appendix Appendix Before Using the Optional Wireless LAN This manual describes the procedures required to properly set up and configure the optional integrated Wireless LAN Mini-PCI device (referred to as "WLAN device" in the rest of the manual). Before using the WLAN device, read this manual carefully to ensure its correct operation. Keep this manual in a safe place for future reference. Wireless LAN Devices Covered by this Document This document is applicable to systems containing the following device: • Intel® Dual Band Wireless-N 7260 Characteristics of the WLAN Device • The WLAN devices are PCI Express Mini cards attached to the main board of the mobile computer. • The WLAN devices operate in license-free RF bands, eliminating the need to procure an FCC operating license. The WLAN operates in the 2.4GHz Industrial, Scientific, and Medical (ISM) RF band and the lower, middle, and upper bands of the 5GHz Unlicensed National Information Infrastructure (UNII) bands. • The WLAN devices are capable of four operating modes, IEEE802.11a, IEEE802.11b, IEEE802.11g, and IEEE802.11n. • The WLAN device is Wi-Fi certified and operates (as applicable) at a the maximum data rate of 450 Mbps in IEEE802.11n mode (300 Mbps in this configuration); 54 Mbps in IEEE802.11g mode; and 11 Mbps in IEEE802.11b mode. • The WLAN devices support the following encryption methods - WEP, TKIP, CKIP, and AES encryption. • The Wireless LAN devices are compliant with the following standards: WPA, WPA2, CCX1.0, CCX2.0, CCX3.0, and CCX4.0. Wireless LAN Modes Using this Device Ad Hoc Mode "Ad Hoc Mode" refers to a wireless network architecture where wireless network connectivity between multiple computers is established without a central wireless network device, typically known as Access Point(s). Connectivity is accomplished using only client devices in a peer-to-peer fashion. That is why Ad Hoc networks are also known as peer-to-peer networks. Ad Hoc networks are an easy and inexpensive method for establishing network connectivity between multiple computers. Ad Hoc mode requires that the SSID, network authentication, and encryption key settings are identically configured on all computers in the Ad Hoc network. Fujitsu 89
Appendix Access Point (Infrastructure) Mode Infrastructure mode refers to a wireless network architecture in which devices communicate with wireless devices by communicating through an Access Point. In infrastructure mode, wireless devices can communicate with each other or with a wired network. Corporate wireless networks operate in infrastructure mode because they require access to the WLAN in order to access services, devices, and computers (e.g., file servers, printers, databases). 90 Fujitsu
Appendix * = An optional hub for a wired LAN may be required depending upon the type of access point used. ** = ADSL modem, cable modem, or similar How to Handle This Device The WLAN device is an optional device that may come pre-installed in your mobile computer. Under normal circumstances, it should not be necessary for you to remove or re-install it. The Operating System that your mobile computer comes with has been pre-configured to support the WLAN device. • Integrated Intel Centrino wireless LAN devices support IEEE802.11a, IEEE802.11b, IEEE802.11g, and IEEE802.11n. • The WLAN device operates in the 2.4 GHz ISM band and the 5 GHz lower, middle, and upper UNII bands. • Microwave ovens may interfere with the operation of WLAN devices since they operate in the same 2.4 GHz frequency range as IEEE802.11b/g/n devices. Interference by microwaves does not occur with IEEE802.11a radio which operates in the 5 GHz RF band. • Wireless devices that transmit in the 2.4 GHz range may interfere with operation of WLAN devices in IEEE802.11b/g/n modes. Symptoms of interference include reduced throughput, intermittent disconnects, and many frame errors. It is HIGHLY recommended that these interfering devices be powered off to ensure proper operation of the WLAN device. ** * Fujitsu 91
Appendix Deactivating/Disconnecting the WLAN Device Disconnecting the WLAN device may be desired in certain circumstances (to extend battery life) or where certain environments require it (i.e. hospitals, clinics, airplanes, etc.). The WLAN device can be disconnected in Windows using the WLAN icon in the system tray (Note that disconnecting via the icon in the system tray does not turn off the radio; it continues to transmit and receive even though it’s not connected.) The radio components are switched on and off using the appropriate functions of the operating system. ► To switch radio components on and off individually, select Settings – Change PC settings – Wireless – Wireless devices – Off. Configuring the Wireless LAN The optional WLAN device can be configured to establish wireless network connectivity using the software that is built into Windows. Support for most industry standard security solutions is contained in this software. Pre-defined parameters will be required for this procedure. Please consult with your network administrator for these parameters: Connection to the network After you have configured your computer, you can connect to an active network by performing the following steps: 1. Click on the WLAN icon in the system tray. 2. Select Connect to a network. 3. Select a network from the list that appears, and click the Connect button. Troubleshooting the WLAN Causes and countermeasures for troubles you may encounter while using your wireless LAN are described in the following table. 92 Fujitsu
Appendix Problem Possible Cause Possible Solution Unavailable network connection Incorrect network name (SSID) or network key Ad hoc connection: verify that the network names (SSID’s) and network keys (WEP) of all computers to be connected have been configured correctly. SSID’s and WEP key values must be identical on each machine. Access Point (Infrastructure) connection: set the network name (SSID) and network key to the same values as those of the access point. Set the Network Authentication value identically to that of the Access Point. Please consult your network administrator for this value, if necessary. Weak received signal strength and/or link quality Ad hoc connection: Retry connection after shortening the distance to the destination computer or removing any obstacles for better sight. Access Point (Infrastructure) connection: Retry connection after shortening the distance to the access point or removing any obstacles for better sight. Fujitsu 93
Appendix Problem Possible Cause Possible Solution Unavailable network connection (continued) The WLAN device was deactivated or is disabled Check if the wireless switch is turned On. Go to Start > Control Panel, and doubleclick on Windows Mobility Center. If the wireless network is off, click the Turn wireless on button. The computer to be connected is turned off Check if the computer to be connected is turned ON. Incorrectly configured network settings Recheck the configuration of your network settings. RF interference from Access Points or other wireless networks The use of identical or overlapping RF channels can cause interference with the operation of the WLAN device. Change the channel of your Access Point to a channel that does not overlap with the interfering device. Wireless network authentication has failed Re-check your Network Authentication, Encryption, and Security settings. Incorrectly configured security settings such as an incorrectly typed WEP key, a mis-configured LEAP username, or an incorrectly chosen authentication method will cause the LAN device to associate but not authenticate to the wireless network. Incorrect IP address configuration This only applies to networks using static IP addresses. Please contact your network administrator for the correct settings. 94 Fujitsu
Appendix Using the Bluetooth Device Bluetooth is integrated into the Wireless LAN module. The Bluetooth capabilities are Bluetooth Basic, EDR and Bluetooth Low Energy (BT v4.0) operational modes. What is Bluetooth? Bluetooth technology is designed as a short-range wireless link between mobile devices, such as laptop computers, phones, printers, and cameras. Bluetooth technology is used to create Personal Area Networks (PANs) between devices in short-range of each other. To enable or disable either the wireless LAN or Bluetooth devices individually, perform the following steps: 1. Go to the Modern Start screen and select Charms > Settings > Change PC Settings > Wireless. 2. Under Wireless > Wireless Devices click on the Bluetooth switch to turn it on. Where to Find Information About Bluetooth For additional information about Bluetooth Technology, visit the Bluetooth Web site at: "www.bluetooth.com". FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The Bluetooth antenna is located on the top edge of the LCD screen and is exempt from minimum distance criteria due to its low power. The transmitters in this device must not be co-located or operated in conjunction with any other antenna or transmitter. Canadian Notice To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. Warranty Users are not authorized to modify this product. Any modifications invalidate the warranty. This equipment may not be modified, altered, or changed in any way without signed written permission from Fujitsu. Unauthorized modification will void the equipment authorization from the FCC and Industry Canada and the warranty. Image Backup and Recovery Procedures Thank you for purchasing a Fujitsu computer. Fujitsu is committed to bringing you the best computing experience with your new system. It is very important that you create DVD copies of your Recovery Image and Bootable Disk before beginning to use your system. To do so, follow the instructions in the “Creating a Backup of Bootable Disk and Recovery Image” section of this document. Fujitsu 95
Appendix It is also important that you create a copy of the software that is essential for your system to access the internet (hereafter called “essential access software”) to external writable media or an external drive. To do so, follow the instructions in the “Creating a Backup of the System-Specific Software Drivers”. Creating a Backup of Bootable Disk and Recovery Image When you purchased your new system, a copy of the recovery image was loaded into a hidden partition on your hard disk drive. Having a copy of the recovery image available to you means that in the event of system failure, you will be able to restore it and re-install the essential access software using Fujitsu Software Auto Installer. To make a copy of the recovery image to DVD disks, you will need three or four blank disks to create the copy. After creating the copy, be sure to label the disks and keep them in a safe place to ensure they do not get damaged. Note: If your system does not have an internal writable DVD drive, connect your system to an external drive* before beginning the following steps. 1. Launch System Restore and Recovery from the desktop icon. It will allow you to create the Bootable Disk and the Recovery Image Disk Set. 2. On “Step 1: Select the Bootable Disk from the list”: a. Select a media type. b. Notice the number of disks that are needed for the set. c. Click Next to proceed. 3. On “Step 2: Confirm your Recovery Disk”, click Next. 4. On “Step 3:” follow the on-screen instructions to make the disk or disk set, then click Start. It takes approximately 20 minutes to make one disk. 5. On “Step 4”, when the disk creation is completed, a message appears. Click Finish to exit the program. 6. Repeat Step 1: Select Recovery Disk from the list and repeat the above steps 2(a), 2(b), 2(c), 3, 4 and 5. * DEPENDING UPON YOUR OPTICAL DRIVE AND MEDIA FORMAT USED, SOME MEDIA TYPES MAY BE INCOMPATIBLE FOR CREATING IMAGE BACKUPS. 96 Fujitsu
Appendix Creating a Backup of Essential Access Software When you purchased your new system, a “Fujitsu Software Extractor” shortcut was loaded to “C:\Fujitsu\Drivers\AutoInstaller\”. This shortcut allows you to save the software driver packages along with the extracted Auto Installer software package to a selected location. It is recommended that you save these packages to writable media or an external drive. This ensures that in the event of system failure you will be able to re-install the essential access software. 1. Open the C:\Fujitsu\Drivers\AutoInstaller\ folder 2. Run “Fujitsu Software Extractor” as an Administrator a. Right-click on Fujitsu Software Extractor. b. Select the “Run as Administrator” option from the menu that is displayed. 3. The default save location is C:\Fujitsu\ AutoInstaller\ Drivers\. You can change the location by clicking on the Browse button and selecting your preferred location. Note: It is recommended that you change the default location and save the software packages to the external writable media or drive. 4. Click on the Save Packages button. 5. Fujitsu Software Extractor copies the zipped software packages and Readme files, and extracts the Auto Installer folder to the selected location. Note: The extracted Auto Installer will later be used to install the software automatically on the system in the event of generic image restoration when the software is not pre-installed in the image. RECOVER YOUR SYSTEM WHEN THE HARD DRIVE IS STILL ACCESSIBLE Using the Recovery and Utility Tools The Recovery and Utility tools consist of a variety of tools that will help you recover your recovery image and system images, and delete the data from your hard disk. Methods for accessing the utilities Recovery and Utility Tools are preinstalled in a hidden partition by the factory, or they can be accessed by using the bootable disk. Note: The Recovery and Utility tools may be deleted from your hard disk drive if you modify the partitions. If that occurs, you will not be able to use the hidden partition for booting to Recovery and Utility Tools, but you will still be able to boot from the Bootable Disk. Fujitsu 97
Appendix Enter Determining whether Recovery and Utility is pre-loaded 1. Turn on or reboot your system. When the Fujitsu logo appears, press the key. 2. Use the key to get to the Application Menu. 3. Check whether the Recovery and Utility option is present. If it is not present, it means that the utility must be used from the Bootable Disk. Proceed to “Running Recovery and Utility from the Bootable Disk” if Recovery and Utility is unavailable. Running Recovery and Utility from hard disk 1. Turn on or reboot your system. When the Fujitsu logo appears, press the key. 2. Use the key to get to the Application Menu. 3. Cursor down to Recovery and Utility and press the key. 4. Choose your language, if necessary. Select Recovery and Utility to proceed. 5. Three tool options appear: Diagnostics, Recovery, and Utility (refer to the Recovery and Utility tools section below for instructions on how to use these tools). 6. If this was successful please skip the next step and go to “Recovery and Utility tools.” 7. If this was NOT successful, please go to the next step. Running Recovery and Utility from the Bootable disk To verify/change the boot-up priority (rather than booting-up from the hard drive or an external media drive), perform the following steps: 1. Power on your system. When the Fujitsu logo appears on the screen, press the 2. Insert the bootable disk into the drive tray. 3. Highlight the CD/DVD option from the Boot menu, then press Enter . 4. Click OK. key. 5. Select CD/DVD boot mode: UEFI Mode, if applicable, and then press . While the files are being loaded from the disk, the Fujitsu logo screen will appear followed by a progress bar at the bottom of the screen. F12 Tab F12 Tab Enter F12 98 Fujitsu
Appendix Recovery and Utility tools Note: Recovery and Utility tools may not be available on your system depending on the region from which the system was shipped. Diagnostics tool: The Diagnostics tool is designed for use by IT professionals. It is not likely you will need to use this tool. If you should need to use this tool, perform the following steps: 1. Press the Diagnostics Tool button to start the Diagnostics tool. 2. Read the note, and then click OK. 3. Choose one or more of the following options for diagnostics on the Fujitsu Hardware Diagnostics Tool window: CPU, Memory, Display, Hard Disk, CD/DVD/BD, Floppy Disk, Keyboard, and Mouse. 4. Click the Option button in the Tool menu to specify how many times the tool should run diagnostics on each selected component. 5. Press Execute to start the Diagnostics tool. 6. After the execution is completed, the selected components are circled in red to indicate that they have been diagnosed and the result dialog window opens. Click Close to close the window. 7. Click End to close the Diagnostics tool, and then click Yes to confirm the end of diagnostics session. Recovery tool: The Recovery tool contains two options: • Restore C Drive: Restore recovery image (only C: drive) • Restore Full Hard Drive: Restore recovery image (full hard drive). You can use these tools to restore the Recovery Image from the hidden partition, and perform a full hard drive recovery. Please refer to instructions above for details on how to create a Recovery Image. Restore the Recovery Image from Hidden Partition 1. Click [Restore C: drive] from Recovery and Utility tools 2. The progress bar is followed by “Restore Recovery image (only C: drive)” screen confirming that the Image will be restored to the C: drive. Click Next. 3. Read the instruction screen and select Agree, then click Next. 4. Click OK to acknowledge the warning message to restore recovery image to the C: drive. 5. When the progress bar appears, wait for the process to complete. 6. Click Finish when the process completes; the computer will restart to Windows. 7. Follow the steps listed in the “Auto Installation support for software packages from hidden partition” section. 8. Download FSDM (Fujitsu Software Download Manager) from the support site and download all the software applicable to the model and OS using FSDM. 9. Follow the steps listed in “Auto Installation support for software packages downloaded from support website” section. Fujitsu 99
Appendix RECOVER YOUR SYSTEM WHEN THE HARD DRIVE IS NOT BOOTABLE Restore the Recovery Image for Full Hard Drive Follow the steps in the “Recovering your Recovery Image using Recovery and Utility (for new hard drive or non-bootable hard drive)” section. You will need the Bootable Disk and the Recovery Disk Set for this task. Utility tool: If applicable for your region, the Utility tool contains two options: Hard Disk Data Delete and Partition Creation. The Hard Disk Data Delete utility is used to delete all data on the hard disk and prevent the data from being reused. NOTE: Do not use the Hard Disk Data Delete utility unless you are absolutely certain that you want to erase your entire hard disk, including all partitions. To delete hard disk data: 1. Click the Hard Disk Data Delete button. The progress bar appears, followed by the EULA screen. 2. Agree to the EULA and click Next. 3. Choose the hard disk from which the data should be deleted in the list of hard disks and click Next. The Partition Creation utility is used to change the C: and D: drive partition sizes. To run this utility: (This is not an option when using Windows 7.) 1. Click the Partition Creation button. 2. A progress bar appears, followed by the EULA screen. Agree to the EULA. 3. On the Recovery Tool - Partition Creation screen, move the slider to set disk size, and then click OK. 4. Click Yes in the Partition Creation confirmation dialog. WARNING: It is highly recommended that you send your product to Fujitsu Service to replace a hard drive. A mistake could possibly destroy your computer, your new hard drive or both. 100 Fujitsu
Appendix Recovering Your Recovery Image Using Recovery and Utility (for new hard drive or non-bootable hard drive) If you have installed a new hard drive or your hard drive is not bootable, perform the following steps. Note: You will need the Bootable disk and Recovery Image disk set for this recovery. 1. Power on your system. When the Fujitsu logo appears on the screen, press the 2. Insert the bootable disk in your DVD drive, then click OK. 3. Highlight the CD/DVD option from the Boot Menu and press Enter . 4. Select CD/DVD boot mode: Select UEFI Mode, if applicable and press Enter . While the files are being loaded from the disk, the Fujitsu logo screen appears followed by a progress bar at the bottom of the screen. 5. Choose your language, if necessary. 6. Three tool options appear: Diagnostics, Recovery and Utility. Select Recovery. • For Windows 8.1: Select Restore full hard drive • For Windows 7: Select Restoring the Factory Image (full hard drive recovery) 7. Click Next to confirm full hard drive restoration. All data on HDD will be deleted. 8. Agree to EULA by selecting Agree option and clicking Next. 9. Click Next on the Recovery Disk Check screen to verify that the bootable disk has been inserted into the optical drive. 10. The Checking for Recovery Disk screen appears followed by the prompt to insert the first disk. Click OK to continue. Repeat this step for all disks. After all recovery disks have been checked and the check has been completed, click Next. 11. Follow the prompt to reinsert the first recovery disk and click Next. 12. Click OK when you receive the final warning informing you that all data on drive C will be lost. This starts the recovery process. 13. Follow the prompts to insert the next recovery disks and click OK. 14. After the copying of the image to the HDD completes the restore process is complete, click Finish to restart the system. The computer will restart automatically and then go through the first boot process. 15. Follow the steps listed in “Auto Installation support for essential access software from backup location” section. key. 16. Download FSDM (Fujitsu Software Download Manager) from support site and download all the software applicable to the model and OS using FSDM. 17. Follow the steps listed in “Auto Installation support for essential access software downloaded from support website. Enter Fujitsu 101
Appendix Installing the Software after the Recovery Image is Restored Auto-installation support for essential access software from hidden partition The below listed steps are applicable only in cases in which the recovery image restore and hidden partition contents have not been wiped out. 1. After the recovery image is restored, launch the desktop icon “Fujitsu Software Auto Installer”. 2. Double-click on “Fujitsu Software Auto Installer” desktop icon. 3. Click Yes on User Account Control Dialog box. This will take some time to process the software packages. A message will be displayed during this time, “Please wait while the content is being processed”. 4. If EULA is displayed for Fujitsu Software Auto Installer, accept the EULA, otherwise continue. 5. Then Fujitsu Software Auto Installer user interface will be launched providing ability to auto-install the essential access software on the system. 6. It is recommended that you install all the software in the listed order. You can Select All, to install the software in the order listed. 7. Click Install to start the installation. 8. After installing all the selected drivers, Installation Results window will be displayed. Click OK. 9. “You must restart the system for the settings to take effect. Do you wish to reboot now?” message appears. Select Yes. 10. The system will now reboot. 11. You can now connect to the internet and download FSDM (Fujitsu Software Download Manager) from the support site and download all the software applicable to the model and OS using FSDM if they are not downloaded yet. 102 Fujitsu
Appendix Auto-installation support for essential access software from backup location The below listed steps are applicable in cases in which a backup copy was created as mentioned in the section “Creating a Backup of essential access software”. 1. It is important to have the extracted Auto installer software package folder and Readme file in the same location as other software folders. Otherwise auto-installation of the software will not be supported. 2. Inside the Auto Installer software package, launch FjAutoinstall.exe as an Administrator. 3. Click Yes on the User Account Control dialog box. This will take some time to process the software packages. A message will be displayed during this time stating, “Please wait while the content is being processed”. 4. If EULA is displayed for Fujitsu Software Auto Installer, accept the EULA, otherwise continue. 5. The Fujitsu Software Auto Installer user interface will be launched providing ability to auto install the essential access software on the system. 6. It is recommended that you install all the software in the listed order. You can “Select All”, to install the software in the order listed. 7. Click the Install button to start the installation. 8. After installing all the selected drivers, Installation Results window is be displayed. Click OK. 9. “You must restart the system for the settings to take effect. Do you wish to reboot now?” message appears. Select Yes. 10. The system will now reboot. Auto Installation support for the software downloaded from support website 1. Download FSDM (Fujitsu Software Download Manager) from the support site and download all the drivers applicable to the model and OS using FSDM if they are not downloaded yet. 2. When the software packages are downloaded from web, it is important to download the Auto Installer Software package and the model/language- specific Readme file if you prefer to auto install the software. 3. It is important to have the extracted Auto Installer software package folder and Readme file in the same location as other software folders. Otherwise auto-installation of the software will not be supported. 4. Inside the Auto Installer software package, launch FjAutoinstall.exe as administrator. 5. Click Yes on the User Account Control dialog box. This will take some time to process the software packages. A message will be displayed during this time stating “Please wait while the content is being processed”. 6. If EULA is displayed for Fujitsu Software Auto Installer, accept the EULA, otherwise continue. 7. The Fujitsu Software Auto Installer user interface will be launched providing the ability to auto install the software downloaded from support site. 8. It is recommended that you install all the software in the listed order. You can Select All, to install the software in the order listed. 9. Click the Install button to start the installation. 10. After installing all the selected drivers, the Installation Results window is displayed. Click OK. 11. “You must restart the system for the settings to take effect. Do you wish to reboot now?” message appears. Select Yes. 12. The system will now reboot. Fujitsu 103
Appendix Downloading Driver Updates To ensure that you always have the most current driver updates related to your system, you should occasionally access the Fujitsu Software Download Manager (FSDM) utility. The FSDM utility is available from the Fujitsu Support site. FSDM will allow you to view and download a list of the most current drivers, utilities, and applications to determine whether you have the latest versions. To download the FSDM Utility, go to the Support Site: "http://support.fujitsupc.com/CS/Portal/support.do?srch=DOWNLOADS". If you are planning on downgrading, upgrading or changing versions of your operating system during this process please see the User’s Guide for more information at "http://solutions.us.fujitsu.com". 104 Fujitsu
Index Index A AC adapter connecting 16 Set up 16 Acoustic warnings 74 Anti-theft protection 55 Audio connections 64 B Battery 33 battery charge 34 Caring for and maintaining 33 charge level 33 Charging 33 Discharges too quickly 73 see Rechargeable battery 33 Service life 33 battery charge meter 33 BIOS Setup Utility , protecting with password 55 calling 65 exiting 67 operation 66 Settings 65 Bluetooth, Safety notes 12 Bonus Apps 18 C Charging back-up battery 69 Choose a location 16 Cleaning 14 Configuration, BIOS Setup Utility 65 Configuring hardware 65 Configuring system 65 Connecting audio devices 64 Connecting headphones 64 Connecting microphone 64 Cradle 41 Connecting a Tablet PC 43 Crystal View screen cleaning 14 D dark touchscreen 70 Date not correct 69 Declarations of conformity 85 Display orientation select 23 Display Port 62 DOC (INDUSTRY CANADA) NOTICES 83 E Ending energy saving mode 72 Energy Energy consumption 34 Energy saving 12 Energy saving functions 34 Error messages on the screen 75 Errors Acoustic warnings 74 Screen messages 75 Ethernet LAN 39 F Fault Elimination 68 Fingerprint sensor 54 configuring 54 First-time setup 15 G Getting started 15 GPS 39 H HDMI port 61 I Important notes 11 Incorrect time 69 Information, safety 11 Instructions Cleaning 14 K Keyboard cleaning 14 L Landscape format display 23 M Making ready to use 16 Fujitsu 105
Index Memory card handling 35 inserting 35 removing 36 Mobile operation 12 Monitor connection 62 no image 71 remains blank 71 unstable image 71 Monitor connection see VGA port 62 N Notebook switching off 21 Notes 11 disposal / recycling 83 Energy saving 12 touchscreen 22 Transport 12 O Operating system activating system protection 57 cancel system protection 57 Protecting with password 56 P Packaging 15 Password changing 56 entering 56 removing 56 Password protection 55 hard disk 57 Pen 29 Portrait format display 23 Ports 41 Slice keyboard 45 Power saving 12 Power-on Power-on indicator 20 Printer does not print 72 Problem solving 68 R Rechargeable battery see battery 33 S Safety information 11 Screen connection see VGA port 62 Security functions 54 SmartCard 59 SystemLock 59 Security Lock Anti-theft protection 55 using 55 Service life, battery 33 Set up Device 16 Setup see BIOS Setup Utility 65 Slice keyboard Connecting a Tablet PC 46 Ports 45 Slot Memory cards 35 Status indicators 19 Summer time 69 Supervisor password change 56 entering 56 removing 56 Suspend/Resume button 20 Switching on for the first time 17 Symbols Indicators 19 System settings, BIOS Setup Utility 65 T Tablet operating 19 Tablet PC cannot be started 72 cleaning 14 doesn’t work 72 transporting 12 Tablet, operation 19 Tablet: Switching on 20 Technical data AC adapter 80 The wireless connection to a network does not work 73 Time not correct 69 Tips 68 Touchpad cleaning 14 106 Fujitsu
Index Touchscreen cleaning 14 difficult to read 70 notes 22 reflected glare 70 remains dark 70 TPM 60 Transport Damage during transportation 15 Transportation 12 Troubleshooting 68 Trusted Platform Module 60 U USB ports 63 User password change 56 entering 56 removing 56 V VGA port 62 W Webcam 33 Winter time 69 Wireless components Safety notes 12 Wireless LAN Safety notes 12 Wrong date/time 69 Fujitsu 107

Navigation menu