Mitsumi Electric Co WLPS3 VoIP Mobile Phone Terminal User Manual UGform

Mitsumi Electric Co Ltd VoIP Mobile Phone Terminal UGform

Contents

Users Manual 1

MH250USERS GUIDENEC Infrontia Corporation2006 AugustNWA-xxxxxx-001Issue 1.0
LIABILITY DISCLAIMERNEC Infrontia Corporation reserves the right to change the specifications,functions, or features, at any time, without notice. NEC Infrontia Corporation has prepared this document for use by itsemployees and customers. The information contained herein is the propertyof NEC Infrontia Corporation and shall not be reproduced without priorwritten approval from NEC Infrontia Corporation. All brand names andproduct names on this document are trademarks or registered trademarks oftheir respective companies.Copyright 2006NEC Infrontia Corporation
User Safety Protocol …………………………………………………………………………………………………… Important: Read this information before using your MH250 Handset. Observe the following instructions to use this product safely, prevent you and other people from possible injury, and protect properties. Improper handling may cause heat, explosion, and fire. Danger Recharge the battery with the matching battery charger (see battery label description). Use the battery only for this MH250 handset system. Do not use it with other electrical devices. Keep the following warnings to prevent the battery pack from heating, explosion, and fire. • Do not throw the battery pack into fire. • Do not solder the battery pack directly. • Do not short the positive (+) and negative (-) terminal of the battery pack with metal. • Do not poke the battery nor smash it with hammer. Do not disassemble nor modify the battery pack. It has a safety circuit and a damaged circuit may cause heat, explosion, and fire. The internal liquid of the battery pack has strong acid. If the battery liquid gets into your eye, rinse your eye well with water and consult with a doctor. Do not use, leave, nor recharge the battery pack near fire or under the direct sunlight. High temperature may damage the internal safety circuit and may cause malfunction of the recharge, heat, explosion, or fire.
Warning …………………………………………………………………………………………………… Do not use the unit when you notice smoke, strange smell or other unusual happenings. It may cause fire if you continuously use them. Turn off the power switch of the phone system immediately. For the recharger, disconnect the power plug immediately. Confirm that smoke is ceased, and then contact the nearest NEC service office. Never attempt to repair those units by yourself. If you had an accident such as dropping the phone and broke the unit, turn off the power of the phone system immediately. For the recharger, disconnect the power plug immediately. Contact the nearest NEC service office. If you keep using those units, they may cause fire or electrical shock. If water smeared into the unit, turn off the power of the phone system immediately. For the recharger, disconnect the power plug immediately. Contact with the nearest NEC service office. If you keep using those units, they may cause fire or electrical shock. Do not insert flammable or metal objects into the units. If a foreign object were accidentally placed into the units, turn off the power of the phone system and plug out the power adapter. Contact the nearest NEC service office. If you keep using those units, they may cause fire or electrical shock. Pay special attention to children to prevent from similar accidents. Do not attempt to disassemble nor modify the units. It may cause fire, electrical shock, or system malfunction. Modification by a user is prohibited by law. Do not open the units intentionally. It may cause electrical shock or system malfunction. Ask test adjustment, and repair of the units for the nearest NEC service office. Do not twist, put a heavy object, and push the phone system. Such actions may cause damage, fire, or injuries. Do not place a container with water such as a vase, a plant pot, a cup, cosmetics, chemicals, nor a small metal object. Splashing water over the units and foreign metal object inserted into the units may cause fire or electrical shock. Do not use the unit in a high humid area such as a bathroom or near a humidifier. They may cause fire, electrical shock, or system malfunction. Use the specified power adapter, which is attached to the unit. Other adapters may cause fire or system malfunction. Do not damage, or modify the power adapter cord. Do not kink, pull, twist, or bundle it. Do not put a heavy object or heat it. They may cause fire, electrical shock, or system malfunction. Contact the nearest NEC service office for a damaged adapter cord. Do not touch the power plug with a wet hand. It may cause electrical shock or system malfunction. Do not touch the units or replace a battery with a wet hand. It may cause electrical shock or system malfunction. When you hear thunder during using the phone system outside, immediately stop using it and move to a safe place. Do not use a multiple plugs. It may cause fire or electrical shock. Follow the instruction below when you use a battery pack. They may cause heating, explosion, and fire; • Do not put the battery pack into a microwave oven or a pressure chamber. • Do not use other batteries with this battery pack. If the internal battery liquid clung to your skin or clothes, immediately rinse it with clean water to prevent chemical damage to your skin and clothes. Do not use the phone or recharge the battery in a place where fire or explosion may occur. • This phone system does not have explosion protection. Do not use it where a flammable gas such as propane and gasoline are stored. Turn off the power of the phone immediately. Do not recharge the battery in such a place. Do not use near microwave ovens, medical equipments and industrial equipments.
Federal Communication Commission Interference Statement …………………………………………………………………………………………………… This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. IMPORTANT NOTE: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please avoid direct contact to the transmitting antenna during transmitting. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. We declare that the product is limited in CH1 - CH11 by specified firmware controlled in the USA. Equipment Class :Digital Transmission System Notes :WLAN IP Phone FCC Rule Parts Frequency Range(MHZ) Output Watts 15C 2412.0 – 2462.0 0.02 Power Output is Conducted.
INDEX- 4 -INTRODUCTION 1•WHAT IS MH250? 1•KYES AND PARTS 2•ICONS 3•TWO OPERTAION MODES 3GETTING STARTED 5•SHIPPED PARTS 5•HOW TO INSERT THE BATTERY 5•HOW TO CHARGE THE BATTERY 6BASIC OPERATIONS 8•TO TURN ON THE PHONE (STANDBY MODE) 8•TO TURN OFF THE PHONE 8•TO ANSWER A CALL 8•TO REJECT A CALL 8•TO MAKE A CALL 8•TO PLACE A CALL ON HOLD 9•TO TRANSFER A CALL 9•TO REDIAL (LAST NUMBER REDIAL) 9FEATURES 10•TO USE CALL FORWARDING - ALL CALLS 10•TO USE CALL FORWARDING - DON’T ANSWER 10•TO USE CALL FORWARDING - NO RESPONSE 10•TO USE CALL FORWARDING - BUSY 11•TO USE CALL PICKUP 11•TO USE CALL PARK 11•TO USE CALL BACK 12•TO USE CALL WAITING 12•TO USE CONFERENCE 12
INDEX- 4 -•TO LOCK/UNLOCK THE PHONE 12•TO ADJUST RECEIVER VOLUME 13CALL HISTORY 15•TO VIEW CALL HISTORY 15•TO MAKE A CALL FROM CALL HISTORY 16•TO ADD PHONE NUMBER AND NAME TO DIRECTORY 16•TO DELETE A CALL LOG 17•TO DELETE ALL CALL LOGS 18DIRECTORY 19•TO VIEW DIRECTORY 19•TO EDIT GROUP NAME 20•TO ADD A NEW ENTRY 22•TO DELETE A RECORD 23•TO MAKE A CALL 24•TO EDIT 25•TO CREATE AN INSTANCE MESSAGE (IM) 26SPEED DIAL 27•TO SPEED DIAL 27•TO ADD NEW ENTRY/EDIT 27•TO ADD NEWY ENTRY FROM DIRECTORY 29•TO DELETE AN ENTRY 30SETUP 32•DISPLAY BACKLIGHT 32•DISPLAY CONTRAST( 不可？ ) 32•NOTIFY SETTING 33•COURTESY MODE 34•RING/VIBRAOTR 35•RING VOLUME 36
INDEX- 4 -•CALL VOLUME 37•KEY CLICK 38•MUSIC SELECT 39•RTP ALARM 40•H.O. TONE 41•DATE AND TIME ADJUSTMENT 42•DATE FORMAT 43•TIME FORMAT 44•DAYLIGHT SAVING 45•TIME ADJUSTMENT MEANS 46•SNTP QUERY TIME 47•TIME OFFSET 48•PASSWORD 49•LANGUAGE 50LOCAL INFO 51•TO DISPLAY LOCAL INFO 51LOCK/UNLOCK 52•TO LOCK THE PHONE 52•TO UNLOCK THE PHONE 52PRESENCE 54•TO CHANCE PRESENCE 54•TO VIEW PRESENCE 54SHORT MESSAGE 56•SHORT MESSAGE INDICATION 56•TO VIEW SHORT MESSAGE 56•TO SEND A SHORT MESSAGE 57TECHNICAL SPECIFICATIONS 58
INDEX- 4 -•TECHNICAL SPECIFICATIONS 58Template 1• 2
- 4 -1.1.INTRODUCTION• WHAT IS MH250?MH250 is a wireless IP telephone set that complieswith IEEE 802.11b specifications. MH250 has thefollowing features:- PCS/PHS equivalent service features by connectingwith UNIVERGE SV7000, NEAX2400IPX, andWLAN system.- Phonebook, Instant Message, Presence-機能紹介
- 4 -1.• KYES AND PARTSThe phone has the following keys and parts.12CLEARHOLDTRF3456789*0#@ABC ABCGHI JKL MNOPQRS TUV WXYZ(1) Antena(1) Speaker(1) Display(1) UP key(1) OK button(1) B-key(1) RIGHT key(1) HOLD key(1) DOWN key(1) END/PWR key(1) CLEAR key(1) USB Connector(1) Dial pad(1) Microphone(1) AC Adapter Connetor(1) Headset Connector(1) Headset Connector(1) LID(1) A-key(1) LEFT key(1) TRANSFER key(1) SEND key01. Call historyMenu02. Directory03. Speed Dial04. Setup Menu05. Loacl info06. Lock/Unlock07. Change presence08. Short Message09. MaintenanceOK BackTable 1:Keys And Parts1 Antenna2 Speaker3 Display 2.0 inch LCD, resolution is 176 x 220 pixel4LID5UP key6LID7 A-key Used for the left soft key.8 B-key Used for the right soft key.9 OK key Used for the center soft key.10 UP key11 DOWN key12 LEFT key13 RIGHT key14 TRF key15 HOLD key16 SEND key17 CLEAR key18 HOLD key Used for placing the ongoing call in hold.19 Dial Pad * key is also used for Courtesy mode.20 USB Connector Used for connecting USB cable.21 Headset Connector Used for connecting headset.22 Microphone23 AC Adapter Connector
- 4 -1.•ICONSThe following explains icons from left to right.- Power icon ( ): indicates battery strength- Antenna icon ( ): indicates the radio signalstrength received- VoIP icon ( ): indicates communication is avail-able on your phone - VM icon ( ): indicates you have a voice mail- IM icon ( ): indicates you have an instant mes-sage- Lock icon ( ): indicates your phone is locked- Courtesy icon ( ): indicate your phone is in cour-tesy mode- Vibrator icon ( ): indicates vibration is set to ON• TWO OPERTAION MODESThe phone operates in one of the following two modes:- Standby mode (default mode)-Menu modeStandby Mode:When the phone is turned on, it is placed in this mode.The phone displays the 1st screen similar to thefollowing.Menu Mode:Press soft key on the phone to activate Menu2007/01/0112:00Profile1AM 12:58Menu ProF2007/01/0112:00Profile1AM 12:58Menu ProFProF
- 4 -1.mode. The following Main Menu will be displayed.AM 12:58OK ExitMenu02. Directory03. Speed Dial01. Call history04. Setup Menu05. Local info06. Lock/Unlock07. Change presence08. Short Message09. Maintenance
- 7 -2.GETTING STARTED• SHIPPED PARTSMH250 is shipped with the following components.Make sure that you have all before using the phone.• HOW TO INSERT THE BATTERYInsert the battery into the unit as follows.(1) Remove the rear cover from the phone.(2) Connect the cable to the unit and then place thebattery into the unit so that the label may facetoward you.(3) Attach the rear cover again.MH250USERS GUIDEAC Adapater Battery MH250Cradle this bookLabelBatterywhiteredblackConnector
- 7 -• HOW TO CHARGE THE BATTERYBe sure to charge the battery when using the phone forthe first time. You can charge the battery by using oneof the following:•Cradle• PC via USB cable• AC Adapter (direct connection)By Using the Cradle:The phone can be charged by using the shipped cradle.(1) Insert the AC Adapter plug into the jack in thebottom of the cradle.(2) Plug in the AC adapter to an appropriate outlet.(3) Place the phone on the cradle as shown below.(4) Info-LED turns on, indicating the battery is beingcharged.(5) Info-LED turns off when the battery is recharged.By Using the USB Cable:The phone can be charged by using your PC via a USBcable.(1) Insert the USB connector into the USB jack.(2) Insert the other end of the cable to your PC.The empty battery can be recharged forabout 3 hours.AC OutletMH250CradleInfo-LEDAC AdapterJackThe phone is seatedMH250USB connectorUSB juckTo PC
- 7 -By Using the AC Adapter:AC OutletMH250AC Adapter ConnectorAC AdapterJack
- 9 -3.BASIC OPERATIONS• TO TURN ON THE PHONE (STANDBY MODE)Press and hold key for 1 second or more. Thestart screen appears as follows. NoteNote: This initial screen is called Standby Mode inthis book.• TO TURN OFF THE PHONEPress and hold key for 3 seconds or more. “Goodbye!” is displayed.• TO ANSWER A CALLWhen receiving an incoming call, the displayautomatically changes to Incoming Call screen. - To answer the call, press key.- To end the call, press key.Note: When the calling party has been already reg-istered in the Phonebook, the registered nameis displayed.• TO REJECT A CALLTo reject an incoming call, press key.• TO MAKE A CALLTo make a phone call, do one of the following:- Enter the phone number and then press key.- Press key and then enter the phone number.Note: Before making a call confirm the following.(i) Power is ON?(ii) Battery is charged?(iii) VoIP Icon/Antenna icons OK?2007/01/01AM09:27Profile1AM 09:27Func ProfileWelcome!< Standby Mode >Good bye!By pressing? key, you can delete the lastdigit of the dialed number.Incoming Call....5012AM 12:58Answer
- 9 -• TO PLACE A CALL ON HOLDDuring an active call, you can hold the call.- Press key to hold the line. The phone dis-plays:- Press key or key to retrieve the line.• TO TRANSFER A CALLDuring an active call, you can transfer the call to otherphone.- Press key during the call. The phone displays:- After hearing Special Dial Tone, enter the phonenumber to transfer the call. - Press ??? key to complete the transfer.• TO REDIAL (LAST NUMBER REDIAL)You can make a call from the Call History.A maximum of the last 20 calls can be recorded.- Press key in standby mode. The phone dis-plays the Main Menu.- Press key to select “01. Call history” and thenpress key.- Press key to select “01. LNR (Last NumberRedial)” and then press key.- Press key to select a desired party you want toredial and then press key.- Press key or key to redial the party.HOLDHolding...5012AM 12:58End Trans00:01:12UnholdHOLDTRFHolding...5012AM 12:58End Trans00:01:12UnholdMenuMenuAM 12:58OK ExitMenu02. Directory03. Speed Dial01. Call history04. Setup MenuAM 12:58OK ExitRecord select02. CPN03. Missed call01. LNR
- 10 - 4.FEATURES• TO USE CALL FORWARDING - ALL CALLSTo Set:- Enter CALL FORWARDING - ALL CALLS (SET)access code.- Press key and then hear Special Dial Tone.- Dial a desired phone number to which you want toforward incoming calls and then receive Service SetTone (The feature has been set).- Press key.To Cancel:- Enter CALL FORWARDING - ALL CALLS(CANCEL) access code.- Press key and then receive Service Set Tone(The feature has been cancelled).• TO USE CALL FORWARDING - DON’T ANSWERTo Set:- Enter CALL FORWARDING - DON’T ANSWER(SET) access code.- Press key and then hear Special Dial Tone.- Dial a desired phone number to which you want toforward incoming calls and then receive Service SetTone (The feature has been set).- Press key.To Cancel:- Enter CALL FORWARDING - DON’T ANSWER(CANCEL) access code.- Press key and then receive Service Set Tone(The feature has been cancelled).• TO USE CALL FORWARDING - NO RESPONSETo Set:- Enter CALL FORWARDING - NO RESPONSE(SET) access code.- Press key and then hear Special Dial Tone.- Dial a desired phone number to which you want toforward incoming calls and then receive Service SetTone (The feature has been set).- Press key.To Cancel:- Enter CALL FORWARDING - NO RESPONSE(CANCEL) access code.- Press key and then receive Service Set Tone(The feature has been cancelled).
- 11 - • TO USE CALL FORWARDING - BUSYTo Set:- Enter CALL FORWARDING - BUSY (SET)access code.- Press key and then hear Special Dial Tone.- Dial a desired phone number to which you want toforward incoming calls and then receive Service SetTone (The feature has been set).- Press key.To Cancel:- Enter CALL FORWARDING - BUSY (CANCEL)access code.- Press key and then receive Service Set Tone(The feature has been cancelled).• TO USE CALL PICKUPYou can pick up an incoming call within the pickupgroup.- A phone in the call pickup group receives an incom-ing call. The phone starts ringing.- Enter CALL PICKUP access code and then presskey while the phone is ringing.- The call is picked up and then connection is estab-lished.• TO USE CALL PARKYou can park the ongoing call and replace the handset.The opposite party is placed in hold. You can retrievethe held call from the original phone or other phone byusing access code.To Park a Call:- Press key during a call in progress.To Retrieve the Call from the Original Phone- Enter CALL PARK - LOCAL RETRIEVAL accesscode and then press key.To Retrieve the Call from Other Phone:- Enter CALL PARK - REMOTE RETRIEVALaccess code (ex. 11) and the station number of theoriginal phone (ex. 5111) in succession (ex. 11 +5111).- Press key and then connection is established.TRF
- 12 - • TO USE CALL BACKYou can set CALL BACK if the attempted callencounters a busy condition.- Press key and then dial CALL BACK accesscode when the called party is busy.- Receive Service Set Tone and then press key.(Please wait a while until the called party becomesidle)- When the called party becomes idle, your phonerings.- Press key and then receive Ring Back Tone(The opposite party is ringing).- Connection is established when the opposite partyanswers.• TO USE CALL WAITINGTo Activate CALL WAITING - ORIGINATING:- Dial a desired station number - receive Busy Tone.- Press key and then dial CALL WAITINGaccess code.- Receive Special Ring Back Tone.- CALL WAITING tone is sent to the busy station.To Answer the Waiting Call- CALL WAITING TONE is heard.- Press key and then the Waiting Call is auto-matically connected by placing the opposite party inhold.- By pressing key you can switch the callbetween the original party and the new party.• TO USE CONFERENCE- Press key during a call in progress and thenreceive Special Dial Tone. (The opposite party isplaced in hold)- Dial a desired phone number and then receive RingBack Tone.- When the called party answers, press key.- Three-way conference is established.•TO LOCK/UNLOCK THE PHONEYou can lock the phone against unauthorized usage.This is also useful for guarding the phone againstinadvertent button presses.To Lock Keypad:-Press key in standby mode. The phonedisplays the Main Menu.-Press key to select “06. Lock/Unlock” and thenpress key.-Enter your User Password (4 digits) by using dialpad and then press key.-The phone is locked and a lock icon appears.Note: Each number is indicated by a * on the phone.TRFTRFTRFTRFTRFTRFMenuAM 12:58OK ExitMenu07. Change presence08. Short Message06. Lock/Unlock09. Maintenance
- 13 - To Unlock Keypad:-Press key in standby mode. The phonedisplays the Main Menu.-Press key to select “06. Lock/Unlock” and thenpress key.-Enter your User Password (4 digits) by using dialpad and then press key.-The phone is unlocked and the lock icon disap-pears.• TO ADJUST RECEIVER VOLUMEYou can increase or decrease the receiver volume instandby mode or during a call. The volume can be set inseven steps (Level 1[minimum] <=> Level 7[maximum]). The factory value is Level 5.During a Call:Press key to select a desired volume and then press key while talking on the phone.In Standby Mode:- Press key in standby mode. The phonedisplays the Main Menu.- Press key to select “04. Setup Menu” and thenpress key.- Press key to select “02. Sound&Vibrator” andthen press key.- Press key to select “06. Call Volume” and thenpress key.AM 12:58OK ExitPassword* * * * 2007/01/0112:00Profile1AM 12:58Menu ProFMenuAM 12:58OK ExitCall VolumeMenuAM 12:58OK ExitMenu05. Local info06. Lock/Unlock04. Setup Menu07. Change presenceAM 12:58OK ExitSetup Menu02. Sound&Vibrator03. Setup Time01. Display setting04. Password
- 14 - Press key to select a desired volume and then press key.- Press key or key to return thestandby mode.AM 12:58OK ExitSound&Vibrator06. Call Volume07. Key Click05. Ring Volume08. Music SelectAM 12:58OK ExitCall VolumeExit
- 15 - 5.CALL HISTORYThe phone can register recent call history in thefollowing three lists:• Last Number Redial (LNR) • Calling Party Number (CPN)• Missed CallLNR is a list of Dialed Numbers and CPN is that ofReceived Calls. You can make a call from the list andalso add a call log to Directory as needed.• TO VIEW CALL HISTORY- Press key in standby mode. The phonedisplays the Main Menu.- Press key to select “01. Call history” and thenpress key. The phone displays the following.- Press key to select a desired item you want toview on the list and then press key. The phonedisplays the following when “02. CPN” is selected.MenuAM 12:58OK ExitMenu02. Directory03. Speed Dial01. Call history04. Setup MenuAM 12:58OK ExitRecord select02. CPN03. Missed call01. LNRLNR: Last Number RedialCPN: Calling Party NumberAM 12:58Dial BackCPN10/03 PM11:48:5202. Patty01. John10/02 AM07:32:1103. 98123445210/01 PM11:23:0904. Mike10/01 AM10:17:42Func
- 16 - • TO MAKE A CALL FROM CALL HISTORY- Press key to select a desired party you want tomake a call and then press key.- Press key to make the call.Note: If the phone number has not been registered tothe history, Dial button will not appear.• TO ADD PHONE NUMBER AND NAME TO DIRECTORY- Press key to select a desired party you want toadd to Directory.- Press key.- Press key to select “01. DIR Add” and press key.- Press key to select an item you want to edit andthen press key as required. In this exam-ple, Name and Reading will be edited.AM 12:58Dial BackCPN10/03 PM11:48:5202. Patty01. John10/02 AM07:32:1103. 98123445210/01 PM11:23:0904. Mike10/01 AM10:17:42FuncDialAM 12:58Dial BackCPN10/03 PM11:48:5202. Patty01. John10/02 AM07:32:1103. 98123445210/01 PM11:23:0904. Mike10/01 AM10:17:42FuncFuncAM 12:58OK BackCall History02. Delete03. Delete All01. DIR AddAM 12:58Edit BackCPN02. Reading03. 98123445201. Name04. TEL205. TEL306. Note07. Group 108. Entry presenceSaveEdit
- 17 - - Press key to save the data to Directory. • TO DELETE A CALL LOG- Press key to select an item you want to deleteand then press key. - Press key to select “01. Delete” and then press key. - Press key to select “Yes” and then press key.AM 12:58Edit BackCPN02. Yamada Kenichiro03. 98123445201. Ken04. TEL205. TEL306. Note07. Group 108. Entry presenceSaveSaveAM 12:58Dial BackCPN10/03 PM11:48:5202. Patty01. John10/02 AM07:32:1103. Ken10/01 PM11:23:0904. Mike10/01 AM10:17:42FuncFuncAM 12:58Dial BackCPN10/03 PM11:48:5202. Patty01. John10/02 AM07:32:1103. No ID10/01 PM11:23:0904. Mike10/01 AM10:17:42FuncdeleteAM 12:58OK BackCall History02. Delete All01. DeleteAM 12:58OK BackCall History02. Delete All01. DeleteDelete?Call History DeleteYesNo
- 18 - • TO DELETE ALL CALL LOGS- Open a list (LNR/CPN/Missed Call) you want todelete and then press key. - Press key to select “02. Delete All” and thenpress key. - Press key to select “Yes” and then press key to delete all.FuncAM 12:58Dial BackCPN10/03 PM11:48:5202. Patty01. John10/02 AM07:32:1103. No ID10/01 PM11:23:0904. Mike10/01 AM10:17:42Funcdelete allAM 12:58OK BackCall History02. Delete All01. DeleteAM 12:58OK BackCall History02. Delete All01. DeleteDelete?Call History Delete AllYesNo
- 19 - 6.DIRECTORYThe phone can register a maximum of 400 phonenumbers in the Directory. You can make a call from theDirectory.• TO VIEW DIRECTORY- Press key in standby mode. The phonedisplays the Main Menu.- Press key to select “02. Directory”. - The phone displays the following.- Press key. The following menu displays.- Press key to select “01. Search” and then press key. The phone displays Search menu.To Search by Name:- Press key to select “01. Name” and then press key. - Enter a name you want to search in the Directoryand then press key.- Searched items will be displayed.A letter P is added when the person is atarget of PRESENCE feature.MenuAM 12:58OK ExitMenu02. Directory03. Speed Dial01. Call history04. Setup MenuAM 12:58OK FindDirectory02. Aaron03. Julia01. BenFunc04. Paul05. Rachel06. James07. HannahPPPPFuncAM 12:58OK BackMenu02. Edit group name03. Add entry01. Search04. DeleteAM 12:58OK BackSearch02. Phone number03. Group name01. NameAM 12:58OK BackNameJohn
- 20 - To Search by Phone Number- Press key to select “02. Phone number” and thenpress key. - Enter a phone number you want to search in theDirectory and then press key.- Searched items whose phone number starts from“98723” will be displayed.To Search by Group Name- Press key to select “03. Group name” and thenpress key. - Press key to move between Group 1 to Group10.• TO EDIT GROUP NAMEDefault Group Name such as Group 1, can be edited asrequired.- Press key to select “02. Directory” and thenpress key. The phone displays the following.- Press key. The following menu displays.AM 12:58OK BackDirectory02. John Lennon03. John Yamazaki01. John Smith PPAM 12:58OK BackPhone number98723AM 12:58OK BackDirectory02. Jim Baker03. Nancy Williams01. Tom Rolsky PPPAM 12:58OK BackDirectory03. Jim Baker04. Nancy Williams02. Jack Hammer PPP01. Tom Rolsky PGroup 1AM 12:58OK BackDirectory03. Antonio Lopez04. Jose Nakano02. Anny PPP01. Tom PGroup 10Group 1 Group 10AM 12:58OK FindDirectory02. Aaron03. Julia01. BenFunc04. Paul05. Rachel06. James07. HannahPPPPFunc
- 21 - - Press key to select “02. Edit group name” andthen press key. The phone displays Edit GroupName menu.- Press key to select a group you want to edit andthen press key. The phone displays Editscreen.- Edit the group name and then press key.- The edited group name displays.AM 12:58OK BackMenu02. Edit group name03. Add entry01. Search04. DeleteAM 12:58OK FindEdit group name02. Group 203. Group 301. Group 1Func04. Group 4AM 12:58OK FindEdit group namePersonnel Dept.FuncAM 12:58OK BackEdit group name02. Group 203. Group 301. Personnel Dept.04. Group 4
- 22 - • TO ADD A NEW ENTRYYou can add new entry to the Directory.- Press key to select “02. Directory” and thenpress key. The phone displays the following.- Press key. The following menu displays.- Press key to select “03. Add entry” and thenpress key. The phone displays Edit GroupName menu.- Press key to select an item to be edited and thenpress key. - Edit the selected item. In the following example,Name data is edited.- Press key to return the previous screen.AM 12:58OK FindDirectory02. Aaron03. Julia01. BenFunc04. Paul05. Rachel06. James07. HannahPPPPFuncAM 12:58OK BackMenu02. Edit group name03. Add entry01. Search04. DeleteTo add a new entry “Name” must be edit-ted.AM 12:58Edit BackDirectory02. Reading03. TEL101. Name04. TEL205. TEL306. Note07. Group 108. Entry presenceSaveEditAM 12:58OK FindDirectoryDonald E. KeenFuncOK
- 23 - - Press key to select an item to be edited and thenpress key. - Edit the selected item. In the following example,TEL1 data is edited.- Press key to return the previous screen.- Repeat these steps as required for the new entry.- When edit is complete press key. • TO DELETE A RECORDYou can delete a record from the Directory.- Press key to select “02. Directory” and thenpress key. The phone displays the following.- Press key to select a record you want to delete onthe Directory and then press key. - Press key. The following menu displays.- Press key to select “04. Delete” and then press key.AM 12:58Edit BackDirectory02. Reading03. TEL101. Donald E. Keen04. TEL205. TEL306. Note07. Group 108. Entry presenceSaveEditAM 12:58OK FindDirectory975322212FuncOKAM 12:58Edit BackDirectory02. Reading03. 97532221201. Donald E. Keen04. TEL205. TEL306. Note07. Group 108. Entry presenceSaveSaveAM 12:58OK FindDirectory02. Aaron03. Julia01. BenFunc04. Paul05. Rachel06. James07. HannahPPPPFuncAM 12:58OK BackMenu02. Edit group name03. Add entry01. Search04. Delete
- 24 - - Press key to select “04. Delete” and then press key. The phone displays Edit Group Namemenu.• TO MAKE A CALL- On Directory page, press key to select a partyyou want to make a call.- Press key and then the following menudisplays. - Select “05. Dial” and then press key onthe menu.- Press key to make the call.AM 12:58OK BackMenu02. Edit group name03. Add entry01. Search04. DeleteDelete Paul?Directory DeleteYesNoAM 12:58OK FindDirectory02. Aaron03. Julia01. BenFunc04. Paul05. Rachel06. James07. HannahPPPPFuncOKAM 12:58OK BackMenu02. Edit group name03. Add entry01. Search04. Delete05. Dial
- 25 - •TO EDITYou can edit the Directory on a record basis.- On Directory page, press key to select a recordyou want to edit.- Press key and then the following menudisplays.- Select “06. Edit” on the menu.- Press key to edit the record.Note: Presence data is indicated only when therecord is the object of presence feature.d- Press key to select an item you want to edit andthen press key. - When all edit is complete, press key.AM 12:58OK FindDirectory02. Aaron03. Julia01. BenFunc04. Paul05. Rachel06. James07. HannahPPPPFuncAM 12:58OK BackMenu02. Edit group name03. Add entry04. Delete05. Dial06. EditOKAM 12:58Edit BackDirectory03. 9752111104. TEL202. Benjamin01. BenMeeting06. Note07. Group 105. TEL308. Entry presenceSaveNoteEditSave
- 26 - • TO CREATE AN INSTANCE MES-SAGE (IM)You can create an Instance Message from theDirectory.- On Directory page, press key to select a personyou want to send an IM.- Press key and then the following menudisplays.- Select “07. Create IM” on the menu.- Press key to edit the record.- When the message is complete, press key.-AM 12:58OK FindDirectory02. Aaron03. Julia01. BenFunc04. Paul05. Rachel06. James07. HannahPPPPFuncAM 12:58OK BackMenu03. Add entry04. Delete05. Dial06. Edit07. Create IMOKAM 12:58OK SendCreate IMTo: 0123FuncSend
- 27 - 7.SPEED DIALThe phone can use Speed Dial. A maximum of 10entries are available. • TO SPEED DIAL- Press key in standby mode. The phonedisplays the Main Menu.- Press key to select “03. Speed Dial”. - The phone displays a Speed Dial list similar to thefollowing.- To make a call to “03. 96781235” for example,press key and then press key.• TO ADD NEW ENTRY/EDIT- Press key in standby mode. The phonedisplays the Main Menu.- Press key to select “03. Speed Dial”. - The phone displays a Speed Dial list similar to thefollowing.MenuAM 12:58OK ExitMenu02. Directory03. Speed Dial01. Call history04. Setup MenuAM 12:58Enter BackSpeed Dial02. 8215411203. 987654321001. 54332Func04. 5777705. 9674521106. 07. 3AM 12:58Enter BackSpeed Dial02. 8215411203. 9678123501. 54332Func04. 5777705. 9674521106. 07. MenuAM 12:58OK ExitSpeed Dial02. Directory03. Speed Dial01. Call history04. Setup Menu
- 28 - - Select an entry you wan to add by using key. Inthe following example “07.” is selected.- Press key.- The following Speed Dial Menu is displayed. Press key to select “01. Add” and then press key.- Enter a phone number you want to add the list.- Press key and then the new entry is added asfollows.AM 12:58Enter BackSpeed Dial02. 8215411203. 987654321001. 54332Func04. 5777705. 9674521106. 07. AM 12:58Edit BackSpeed Dial02. 8215411203. 987654321001. 54332Func04. 5777705. 9674521106. 07. FuncAM 12:58OK ExitMenu02. DIR refer03. Delete01. Add AM 12:58OK ExitSpeed Dial 07977712345123AM 12:58Enter BackSpeed Dial02. 8215411203. 987654321001. 54332Func04. 5777705. 9674521106. 07. 977712345
- 29 - • TO ADD NEWY ENTRY FROM DIRECTORYYou can add a new entry referring to Directory.- Press key in standby mode. The phonedisplays the Main Menu.- Press key to select “03. Speed Dial”. - The phone displays a Speed Dial list similar to thefollowing. - Select an entry you wan to add by using key. Inthe following example “06.” is selected.- Press key.- The following Speed Dial Menu is displayed. Press key to select “02. DIR refer” and then press key.- The phone displays Directory. Select an entry youwant to add by using key and then press key.MenuAM 12:58OK ExitSpeed Dial02. Directory03. Speed Dial01. Call history04. Setup MenuAM 12:58Enter BackSpeed Dial02. 8215411203. 987654321001. 54332Func04. 5777705. 9674521106. 07. AM 12:58Edit BackSpeed Dial02. 8215411203. 987654321001. 54332Func04. 5777705. 9674521106. 07. FuncAM 12:58OK ExitMenu02. DIR refer03. Delete01. Add AM 12:58OK FindDirectory02. Aaron03. Julia01. Ben04. Paul05. Rachel06. James07. HannahPPPP
- 30 - - Select a phone number you want to add by using key and then press key.- The new entry is added as follows.• TO DELETE AN ENTRYYou can delete an entry from the Speed Dial list.- Press key in standby mode. The phonedisplays the Main Menu.- Press key to select “03. Speed Dial”. - The phone displays a Speed Dial list similar to thefollowing. - Select an entry you wan to delete by using key.In the following example “04.” is selected.- Press key.AM 12:58OK BackDirectory02. 501203. TEL 301. 987611112AM 12:58Enter BackSpeed Dial02. 8215411203. 987654321001. 54332Func04. 5777705. 9674521106. 981611112 07. MenuAM 12:58OK ExitSpeed Dial02. Directory03. Speed Dial01. Call history04. Setup MenuAM 12:58Enter BackSpeed Dial02. 8215411203. 987654321001. 54332Func04. 5777705. 9674521106. 07. AM 12:58Edit BackSpeed Dial02. 8215411203. 987654321001. 54332Func04. 5777705. 9674521106. 07. Func
- 31 - - The following Speed Dial Menu is displayed. Press key to select “03. Delete” and then press key.- The following message is displayed. To delete theentry select “Yes” and then press key. Whenyou do not want to delete the entry, select “No” andthen press key.AM 12:58OK ExitMenu02. DIR refer03. Delete01. Add AM 12:58OK ExitMenu02. DIR refer03. Delete01. Add Delete 57777?Number DeleteYesNo
- 32 - 8.SETUPThe phone can set xxxxx. • DISPLAY BACKLIGHT- Press key in standby mode. The phonedisplays the Main Menu.- Press key to select “04. Setup Menu” and thenpress key.- The phone displays the Setup Menu.- Press key to select “01. Display setting”.- Press key to open “Display setting” menu.- Press key to select “01. BackLight Level” andthen press key.- Backlight can be set in five levels (0 - 4). Select adesired level by using key and then press key.• DISPLAY CONTRAST( 不可？ )- Press key in standby mode. The phonedisplays the Main Menu.- Press key to select “04. Setup Menu” and thenpress key.- The phone displays the Setup Menu.MenuAM 12:58OK ExitMenu02. Directory03. Speed Dial01. Call history04. Setup MenuAM 12:58Enter BackSetup Menu02. Sound&Vibrator03. Setup Time01. Display settingFunc04. Password05. 言語設定AM 12:58Enter BackDisplay setting02. Contrast03. Notify setting01. BackLight LevelFuncAM 12:58OK BackBacklightAM 12:58OK BackBacklightLevel 3Level 0MenuAM 12:58OK ExitMenu02. Directory03. Speed Dial01. Call history04. Setup Menu
- 33 - - Press key to select “01. Display setting”.- Press key to open “Display setting” menu.- Press key to select “02. Contrast” and then press key.- Contrast can be set in five levels (0 - 7). Select adesired level by using key and then press key.• NOTIFY SETTINGThe phone can flash the Info-LED when one of thefollowing occurs:• Unanswered Call• Voice Massage• Unopened IM- Press key in standby mode. The phonedisplays the Main Menu.- Press key to select “04. Setup Menu” and thenpress key.- The phone displays the Setup Menu.- Press key to select “01. Display setting”.- Press key to open “Display setting” menu.- Press key to select “03. Notify setting” and thenpress key.AM 12:58Enter BackSetup Menu02. Sound&Vibrator03. Setup Time01. Display settingFunc04. Password05. 言語設定AM 12:58Enter BackDisplay setting02. Contrast03. Notify setting01. BackLight LevelFuncAM 12:58OK BackContrastAM 12:58OK BackContrastLevel 7Level 0MenuAM 12:58OK ExitMenu02. Directory03. Speed Dial01. Call history04. Setup MenuAM 12:58Enter BackSetup Menu02. Sound&Vibrator03. Setup Time01. Display settingFunc04. Password05. 言語設定
- 34 - - Select ON/OFF by using key and then press key.Note: When Off is set, the Info-LED will not flash.However, the ICONS will be displayed.• COURTESY MODEYou can set the phone in Courtesy Mode, in which thefollowing can be set. When the phone is placed in thismode will be indicated on the display.- Press key in standby mode. The phonedisplays the Main Menu.- Press key to select “04. Setup Menu” and thenpress key.- The phone displays the Setup Menu.- Press key to select “02. Sound&Vibrator”.- Press key. Sound&Vibrator menu appears.- Press key to select “01. Courtesy mode” andthen press key.ON OFFKey Tone OFF ONRing OFF ONDemo Sound OFF ONVibrator ON OFFAM 12:58Enter BackDisplay setting02. Contrast03. Notify setting01. BackLight LevelFuncAM 12:58OK BackNotify settingOffOnCOURTESYTONE/VIB.MenuAM 12:58OK ExitMenu02. Directory03. Speed Dial01. Call history04. Setup MenuAM 12:58Enter BackSetup Menu02. Sound&Vibrator03. Setup Time01. Display settingFunc04. Password05. 言語設定AM 12:58OK BackSound&Vibrator02. External Call03. Internal Call01. Courtesy mode04. Private Call
- 35 - - Select On or Off by using key and then press key.• RING/VIBRAOTRYou can set ringer/vibrator pattern on a call kind basis(external call/internal call/private call). - Press key in standby mode. - The phone displays the Main Menu.- Press key to select “04. Setup Menu” and thenpress key.- The phone displays the Setup Menu.- Press key to select “02. Sound&Vibrator”.- Press key. Sound&Vibrator menu appears.- Press key to select “02. External Call/03. Inter-nal Call/04. Private Call” and then press key.- Select “01. Ring” or “02. Vibrator” by using keyand then press key.- Select a pattern or melody by using key and thenpress key.AM 12:58OK BackCourtesy modeOffOnMenuAM 12:58OK ExitMenu02. Directory03. Speed Dial01. Call history04. Setup MenuAM 12:58Enter BackSetup Menu02. Sound&Vibrator03. Setup Time01. Display settingFunc04. Password05. 言語設定AM 12:58OK BackSound&Vibrator02. External Call03. Internal Call01. Courtesy mode04. Private CallAM 12:58OK BackExternal Call02. Vibrator01. Ring
- 36 - •RING VOLUMEFactory Default: 5You can adjust ringer volume. - Press key in standby mode. - The phone displays the Main Menu.- Press key to select “04. Setup Menu” and thenpress key.- The phone displays the Setup Menu.- Press key to select “02. Sound&Vibrator”.- Press key. Sound&Vibrator menu appears.- Press key to select “05. Ring Volume” and thenpress key.- Ring Volume can be set in eight levels (0 - 7). Selecta desired volume by using key and then press key.AM 12:58OK BackRingPattern1Pattern2Pattern3:Pattern10Melody1Melody2:Melody10AM 12:58OK BackVibratorPattern1Pattern2Pattern301. Ring 02. VibratoroffMenuAM 12:58OK ExitMenu02. Directory03. Speed Dial01. Call history04. Setup MenuWhen the phone is in courtesy mode, itwill not ring irrespective of the volume set-ting.AM 12:58Enter BackSetup Menu02. Sound&Vibrator03. Setup Time01. Display settingFunc04. Password05. 言語設定AM 12:58OK BackSound&Vibrator03. Internal Call04. Private Call02. External Call05. Ring VolumeAM 12:58OK BackRing VolumeVolume (0 - 7)

Navigation menu