Mobile Action Technology 16H62R1 Bluetooth 4.0 Low Energy Wristband User Manual
Mobile Action Technology Inc. Bluetooth 4.0 Low Energy Wristband
User Manual
Q-Band Q-62HR User Manual Device Overview Wristband Clasp Core Button Metallic contact for charging How to wear your Q-62HR? Wear Q-62HR on your wrist Put on the wristband with the screen facing up and the band wrapped around your wrist. Align the clasp along the band to find the holes where best fit the clasps. Charge your Q-62HR Fasten Q-62HR with clasp Squeeze both clasps into the holes on the wristband until you hear a click, indicating the band is securely fastened. Change the wristband To charge your Q-62HR, place it in the charging box at the other end of the USB cable. Close the box afterwards, and make sure the Q-62HR is securely covered. Plug the USB connector to either a PC or power adapter to start charging. 1. Spread open both bands with the screen facing up, and press down the screen with your thumb until the core comes off the wristband. 2. Insert the core with screen facing up into the notch from below the wristband. Button up the clasp on the side of the band with 2 holes. Please note that the charging contact should be near the clasp. EN Q-62 HR Q-Band User Manual Get started with Q-62HR Download and Install i-gotU Life app Please download i-gotU Life app from Google Play or the App Store and have it installed on your smartphone: https://play.google.com/store/apps/details?id=com.mobileaction.ilife http://appstore.com/igotulife Apk download: http://global.mobileaction.com/download/apk Supported device • Any Android smartphone (v4.3 and up) with built-in 4.0 Bluetooth connectivity; or • iPhone 4s and later models, iPad 2 and later models, and iPod Touch (all with iOS version 7.0 and up). • A complete list of supported smartphone or mobile devices can be found at: http://ww2.voiis.com/qband/devices.html Start Using Q-62HR 1. Switch between different function modes 1. Long-press the button on the Q-62HR until you see 4 icons on the screen for mode selection. 2. Press the button to switch mode. 3. You’ll be entering the selected mode in 3 seconds. 2. Change display information Information shown on the screen will vary as you press the button on the Q-62HR to toggle between screens. 3. Q-62HR modes Daily mode: Analyzes your daily data, including steps taken and calories burned, and displays current UV index. Sleep mode: Tracks your sleep pattern and quality. Sports mode: Starts a workout and displays information including duration, steps taken, calories burned, UV-index and distance traveled during the workout. Set up Q-62HR Your Q-62HR can be configured directly on the i-gotU Life app. First time setup: 1. Open the i-gotU Life app. 2. A Setup Wizard will be launched automatically. 3. Follow the on-screen instructions to proceed with more settings. Set up a new device from Settings: 1. Open the i-gotU Life app. 2. Tap the app icon at the upper left corner to open function menu. 3. Choose Settings. 4. Tap Setup New Device under MORE DEVICE SETTINGS. 5. Follow the on-screen instructions to continue. Note Your personal information is used to calculate your Base Metabolic Rate (BMR), which determines your calories burned. Features of Q-62HR & i-gotU Life App Silent Alarm Silent Alarm awakes you using gentle vibrations of the Q-62HR. You can dismiss the alarm by long-pressing the button on the Q-62HR. In case you miss the alarm, Q-62HR will alert you again in 5 minutes. Alarms can be set up from: i-gotU Life App Menu -> Silent Alarm. Notification You will be notified with incoming calls, SMS, E-Mail, or alerts from the social apps via vibration. When notified about an incoming call on an Android smartphone, you may reject the call by long-pressing the button on Q-62HR. Notification can be set up from: i-gotU Life App Menu -> Notification. Online Help Android: http://ww2.voiis.com/igotu-life/help.html?language=en iOS: http://ww2.voiis.com/igotu-life/help.html?language=en&platform=ios Nap mode: Awakes you via vibration after a short nap. 4. Icon description Date Alarm Connection Status Current Mode Overall Progress (the average of Calories + Steps) Battery Status UV – Index Important Notice 1. Please make sure your Q-62HR is fully charged when used for the first time. It takes about 2 hours before it is fully charged. 2. Please do not use under water. 3. Please do not use any corrosive chemical to clean the device. 4. The built-in Li-Polymer Battery might be damaged if it remains low voltage for a long time. It is suggested that you charge the battery once every three months to prolong the battery's lifetime, even though you don't use the device very often or do not plan to use it for a while. WEEE Note on environmental protection: After the implementation of the European Directive 2002/96/EU in the national legal system, the following applies: Electrical and electronic devices may not be disposed of with domestic Waste. Consumers are obliged by law to return electrical and electronic devices at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details to this are defined by the national law of the respective country. This symbol on the product, the instruction manual or the package indicates that a product is subject to these regulations. By recycling, reusing the materials or other forms of utilizing old devices, you are making an important contribution to protecting our environment. Q-Band Q-62 HR User Manual Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference and 2) this device must accept any interference received, including interference that may cause undesired operation of the device. FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operating temperature -10° to 65°C (14° to 149°F) Charging temperature 0° to 45°C (32° to 113°F) Power input type DC 5V USB cable Battery type Rechargeable Li-Poly, 3.7 Vdc Input Maximum DC 5V, 0.1A
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0 (Windows) Create Date : 2016:02:16 10:36:28+08:00 Creator Tool : PScript5.dll Version 5.2 Modify Date : 2016:02:16 10:36:28+08:00 Format : application/pdf Title : Microsoft Word - Q62HR_Manual_EN_20160216_FCC+電氣特性.doc Creator : May Document ID : uuid:9d8e52f6-5c38-4283-bfed-9ee407423db2 Instance ID : uuid:42b992ed-2162-416a-86d2-f51edf95f858 Page Count : 3 Author : MayEXIF Metadata provided by EXIF.tools