Mobile Devices Ingenierie C4MAX-3GNA Telematics embedded system User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2655341
Application ID	xkyXpRmNDsz7H1RRw2gaaw==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	82.28kB (1028504 bits)
Date Submitted	2015-06-23 00:00:00
Date Available	2015-12-20 00:00:00
Creation Date	2017-09-28 02:12:24
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-09-28 02:12:24
Document Title	User manual
Document Creator	PDF Architect 2

Mobile Devices Ingénierie
C4MAX-3GNA
Installation Guide
Version 1.1
10/06/2015
Table of contents
Preface ...........................................................................................................3
Warnings and notices ...................................................................................3
1. Hardware features.....................................................................................4
2. Hardware description ...............................................................................5
2.1. C4MAX-3GNA with external antenna...............................................5
2.2. C4MAX-3GNA with internal antenna ................................................6
2.3. Recommendation for both type: ......................................................7
3. Preparing/installing the device ................................................................8
3.1. Open the device to insert a sim card...............................................8
3.2. Connect the GSM/GPS external antenna .....................................10
3.3. Choose the appropriate location for mounting ............................10
3.4. Insert the device on external support .............................................11
3.5. Pin out & Wires description...............................................................13
3.6. Plug the device to the external battery .........................................14
4. Inputs activation threshold .....................................................................14
5. Ouputs information..................................................................................14
6. LEDs sequences .......................................................................................15
7. Support .....................................................................................................15
8. FCC Regulations: .....................................................................................15
9. RF Exposure Information..........................................................................16
10. IC Notice.................................................................................................17
11. IC Radiation Exposure Statement ........................................................17
INSTALLATION GUIDE 2
Preface
The information contained in this installation guide is subject to changes in order to
improve the reliability, design or features without prior notice. Mobile Devices
Ingénierie reserves the right to make changes in the content without obligation to
notify any person or organisation of such changes or improvements. Mobile Devices
Ingénierie can in no event be held liable for technical or editorial errors or omissions
herein, nor for incidental, special or consequential damages from the furnishing,
performance or use of this installation guide.
Please contact our technical support for current updates and supplemental
information concerning the use and operation of this or other Mobile Devices
Ingénierie products.
Warnings and notices
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
Please read the installation guidelines, as well as the safety and operating instructions
before operating your device. Follow all instructions and heed all warnings in the
installation guide.
There is a risk of explosion if the battery is replaced by a wrong battery type. Please
discard empty battery according to local regulations.
INSTALLATION GUIDE 3
1. Hardware features
C4MAX-3GNA
Performance
Power supply
Communication
Positioning
Inertial sensors
Interface & Telematics
features
Processor
RAM
NAND Flash
External power supply 832V
External voltage
measurement
Li-ion battery charger
Li-ion battery
Modem
GSM antenna
GPS receiver
GPS antenna
Internal 3-axis
accelerometer
Internal 3-axis gyroscope
(on option)
(Mini) USB 2.0
Digitals Input / Analog
input
Digital Outputs
1-wire (for driver ID or
temp sensor)
LEDs
RTC
CAN 2.0B interface
Product specific feature
RS232
RS485 / RS422
Bluetooth
Wifi
Other features
Environmental
Connectors
Operating temperature *
Dimensions
SIM card
Dual GSM/GPS external
antenna
ARM 11 - 500MHz
64 Mbytes
256 Mbytes
8-32V
900mA.h
3G US Data module (UE910-NAD)
External or Internal
Sirf Atlas V (A-GPS on option)
External or Internal
±2g, ±4g, ±8g
±250°/s, ±500°/s, ±1000°/s, ±2000°/s
Host / Device / UART powered
(5V out, 500mA max.)
3 (Ignition, alarm and 1 input active
low) / 2
2 (relay-control & immobilizer on
option)
Yes
2 (1 controlled by software)
Yes
If used, RS485 half duplex only, RS422
not possible
2 (1 with RTS/CTS, 1 without)
Full/half duplex RS485 or RS422
Bluetooth 4.0 BLE dual-mode (with
internal antenna)
IEEE Std 802.11n (with internal
antenna)
J1708 (optional) : if used, RS485 and
RS422 are not available.
1708 is compatible with CAN option.
microFIT 20 pins
Mini-USB
2 Fakra connectors for the external
antennas
-30/+70°C
96x54x17mm
Slot
3 meters cable With 27mm Fakra
connectors
*without internal battery
INSTALLATION GUIDE 4
2. Hardware description
2.1. C4MAX-3GNA with external antenna
Front :
1.
2.
3.
4.
5.
6.
GSM connector
GPS connector
USB connector
Molex (20pins) connector
Inner battery switch
Leds
Inside :
1. Internal battery
2. SIM card slot
INSTALLATION GUIDE 5
2.2. C4MAX-3GNA with internal antenna
Front :
1.
2.
3.
4.
USB connector
Molex (20pins) connector
Inner battery switch
Leds
Inside :
1.
2.
3.
4.
Internal battery
Internal GSM antenna
Internal GPS antenna
SIM card slot
INSTALLATION GUIDE 6
2.3. Recommendation for both type:
Move the switch inwards (I) to activate the internal battery.
The switching ON of the internal battery requires a running system. This is
about 10 seconds after ignition (the led 4 must be lit then unlit).
Move the switch outwards (O) to deactivate the internal battery.
The switching OFF of the internal battery is instant. Thus, don't switch off the
internal battery if the device is running without be connected to an external
battery.
The SIM card PIN code must be deactivated.
INSTALLATION GUIDE 7
3. Preparing/installing the device
3.1. Open the device to insert a sim card
Insert a flat screwdriver into the 2 holes and pry it to remove the back cover.
INSTALLATION GUIDE 8
Unscrew the screw at the back of the device
Afterwards pull on the PCB to release it.
INSTALLATION GUIDE 9
3.2. Connect the GSM/GPS external antenna
3.3. Choose the appropriate location for mounting
The ideal location for mounting the device is under the dashboard. However, some
types of coated windshields, as well as windshields with an in-screen heating system
can block GPS signals. External antenna should never be covered by any kind of
object or material, especially not by metal or aluminium. Transmission and reception
of GPS signal is however not hindered by plastic or normal glass. Moreover, put at
least 20 cm between the antenna and a speaker.
INSTALLATION GUIDE 10
3.4. Insert the device on external support
INSTALLATION GUIDE 11
INSTALLATION GUIDE 12
3.5. Pin out & Wires description
Signal
DIG_OUT1
DIG_OUT2
Pin
RS485_A
RS485_B
DIG_IN1
/ TACHO DATA
RS232_CTS1
RS232_RXD2
RS232_RTS1
ONE_WIRE
AN_IN1
VBAT
GND
10
11
12
CANL
13
CANH
IGNITION
ALARM
14
15
16
RS232_RXD1
17
RS232_TXD1
RS232_TXD2
AN_IN2
18
19
20
Colour
Purple
Blue
White with
black
Red with black
Green
Blue with black
Green with
black
Grey with black
Grey
Brown
Red
Black
Yellow with
black
Purple with
black
White
Orange
Orange with
black
Brown with
black
Black with white
Yellow
20
10
19 18 17 16 15 14 13 12 11
8 7 6 5 4 3 2 1
Power supply may be derived directly from the vehicle’s main power or from the
board installation. In the first case, it is an absolute must that a fuse on the main cable
is present.
Ignition wire must always be connected to the vehicle’s ignition OR tied with
the permanent positive to the vehicle’s battery.
Ground must be always connected first. It is mandatory to add a fuse (2A) to
the permanent positive. The closer to the connection point with vehicle
power.
INSTALLATION GUIDE 13
3.6. Plug the device to the external battery
The device must have a direct connection with the main power (external battery).
Mobile Devices advise against the use of intermediate system.
1. Check that all the inputs implied in the wake-up reasons configured on your
device are not connected.
2. Plug the device (black wire) to the ground of the external battery.
3. Plug the device (red wire) to the permanent positive of the external battery.
4. Plug the device (white wire) to the ignition (after contact).
In some case, the use of a circuit breaker can let the ignition (after contact) active.
Thus, the device will be ON indefinitely. So, it’s important to find a signal where the
ignition can be ON or OFF.
Moreover, it is imperative to insulate the GPS antenna in order to avoid it get in touch
with the car’s chassis.
The device should be always plugged to :
• The ground of the external battery.
• A ground point defined by the vehicle manufacturer (if different from
the ground of the external battery).
A circuit breaker should never be enabled as long as:
• Ignition is active.
• Ignition goes OFF since less than 2 minutes. This is the time for the
device to do a proper shutdown.
It is mandatory to add a fuse (2A) to the permanent positive. The closer to
the connection point with vehicle power.
4. Inputs activation threshold
Here are inputs activation thresholds (voltage).
•
•
•
Ignition (active high) is active if voltage greater than 3V (disabled if smaller
than 1V)
Alarm (active low) is active if voltage is below 1V (disabled if greater than 3V)
Digital Input1 (active low) is active if voltage is below 0.5V (disabled if greater
than 3V)
Note: Range voltage on inputs is 0-30V
5. Ouputs information
The two Outputs are active low and they can deliver up to 300mA.
Note: Outputs have a pull-up resistance of 10Kohms
INSTALLATION GUIDE 14
6. LEDs sequences
Green LED (Soft)
Meaning
3 times (50ms ON/100ms
No GPRS/No
OFF)
GPS
3550ms OFF
2 times (50ms ON/100ms
No GPRS/Fix
OFF)
GPS
3700ms OFF
1 time (50ms ON/100ms
GPRS OK/No
OFF)
GPS
3850ms OFF
GPRS OK/Fix
2000ms ON
GPS
2000ms OFF
Sequence
Sequence
Red LED (System)
Meaning
C4MAX3GNA OFF
OFF
Ext.
Power/Run
ON
Int. Bat/Run
ON
Shutdown
(hibernate)
5ms ON/2000ms OFF
Idle/Sleep
(idle)
twice (5ms ON/50ms
OFF)
1895ms OFF
7. Support
For all questions not related in this installation guide, please contact the support team
by email at support@mobile-devices.fr
8. FCC Regulations:
This mobile phone complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
This mobile phone has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiated radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by the party responsible
for compliance could void the user‘s authority to operate the equipment.
INSTALLATION GUIDE 15
9. RF Exposure Information
This device meets the government’s requirements for exposure to radio waves.
This device is designed and manufactured not to exceed the emission limits for
exposure to radio frequency (RF) energy set by the Federal Communications
Commission of the U.S. Government.
This device complies with FCC radiation exposure limits set forth for an uncontrolled
environment. In order to avoid the possibility of exceeding the FCC radio frequency
exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches)
during normal operation.
INSTALLATION GUIDE 16
10. IC Notice
This device complies with Industry Canada license-exempt RSS standard(s). Operation
is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes:
(1) L'appareil ne doit pas produire de brouillage, et
(2) L'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d'en
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
IC: 20253-C4MAX3GNA
11. IC Radiation Exposure Statement
Cet appareil est conforme aux limites d'exposition aux rayonnements de la IC CNR102 définies pour un environnement non contrôlé. Afin d'éviter la possibilité de
dépasser les limites d'exposition aux fréquences radio de l’IC CNR-102, la proximité
humaine à l'antenne ne doit pas être inférieure à 20 cm (8 pouces) pendant le
fonctionnement normal.
INSTALLATION GUIDE 17

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Create Date                     : 2015:06:10 16:24:29+02:00
Creator                         : PDF Architect 2
Modify Date                     : 2015:06:19 15:58:33+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Creator Tool                    : PDF Architect 2
Metadata Date                   : 2015:06:19 15:58:33+08:00
Producer                        : PDF Architect 2
Format                          : application/pdf
Document ID                     : uuid:9bd18460-4bc7-484e-ba88-7090d56776c4
Instance ID                     : uuid:859f9337-bb6d-4648-abc7-6f5be51dc97f
Page Count                      : 17

EXIF Metadata provided by EXIF.tools