MobileHelp WBS-01 WIRELESS BASE STATION GEN1.0 User Manual WBS 1 0
Integrity Tracking LLC, dba MobileHelp WIRELESS BASE STATION GEN1.0 WBS 1 0
User Manual
WBS Gen1.0
USER MANUAL
WBS Gen 1.0
1
Wireless Base Station:
If you need help, WBS calls for help whenever you press
the EMERGENCY button. It works anywhere, anytime there is cellular service.
Where to place WBS in your house
●
On a hard, flat, non-metallic surface.
How to use WBS
(1) Power Up
●
Plug WBS’s power adaptor into a electrical outlet that is NOT controlled by a wall
switch.
●
Power switch ( at the bottom case of WBS) to “ON” position.
Power Switch ON
WBS Gen1.0
2
(2) Calling for Help
●To call for help, you don’t have to do anything except press EMERGENCY
button.
●Once the button is pressed, one of MobileHelp personal response associate
will answer to you.
(3) Communicate with MobileHelp Response Center
●MobileHelp personal response associate will speak to you through your WBS’s
built-in speaker. He/She can hear you through the WBS’s highly sensitive
microphone
.
(4) Received Help
●MobileHelp personal response associate will contact a neighbor, family
member or emergency services based on specific need.
●
The EMERGENCY and RESET button will light up.
●
Indicating that power has been detected by WBS.
●
The voice “system ready” also prompts from WBS at the same time and it is ready
to use.
WBS Gen1.0
3
FCC Regulations:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
This device has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiated radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user‘s authority to operate the equipment.
RF Exposure Information
This device meets the government’s requirements for exposure to radio waves.
This device is designed and manufactured not to exceed the emission limits for
exposure to radio frequency (RF) energy set by the Federal Communications
Commission of the U.S. Government.
This device complies with FCC radiation exposure limits set forth for an uncontrolled
environment. In order to avoid the possibility of exceeding the FCC radio frequency
exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches)
during normal operation.
WBS Gen1.0
4
IC Regulations:
This device complies with Industry Canada license-exempt RSS standard(s). Operation
is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.“
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This Category II radiocommunication device complies with Industry Canada Standard
RSS-310.
Ce dispositif de radiocommunication de catégorie II respecte la norme CNR-310
d’Industrie Canada.
Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry
Canada. To reduce potential radio interference to other users, the antenna type and its
gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not
more than that necessary for successful communication.
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.