Model Racing Technology PTX1 PTX User Manual

Model Racing Technology PTX

User Manual

MODEL RACING TECHNOLOGY PTX version:  PTX-20           PTX-20 Custom / Cloned            ‘Enhanced’Refer to the instructions relevant to the PTX firmware version as shown below: PTX-20  -  the 7 digit ID is selectable from 20 available (Number SET ONE & TWO)PTX-20  Custom / Cloned - the 7 digit ID is selectable from 20 available (as PTX-20)              or custom / cloned ID number can be selected: number shown below as †  MODEL RACING TECHNOLOGY   Tel/Fax: (UK) 0870 1624955   Email: support@team-mrt.com     Website: www.team-mrt.comID Number Display: to show the currently selected ID number, press and releasethe setup button when the PTX is connected to power and is not in 'setup' mode.How to change the ID Number: with PTX connected (LED is on) press and holdthe setup button until the LED flashes. The number of flashes displays the ID thatis set (also press and hold setup button to switch between number SET 1, 2 or 2/o).With the LED flashing in 'setup' mode to change the ID number press and releasesetup button until the required ID is selected (ID 1-10 "flash" or 1-10 "flicker-flash"or “2flash-flash”) disconnect PTX from power to complete the ID number selection.Custom / Cloned ID Number selection: sets custom/cloned number (if available)press and hold the setup button and then connect the PTX, the LED will display a"constant flicker-flash", disconnect PTX to complete selection of custom/cloned ID.*to set a new custom ID (if available) follow instructions for selection as described  but continue to hold, after the ‘warning reset’ flashes ID is set to a new custom ID.*Note: WARNING! If custom ID is reset a new ID will replace the previous ID            (after ID reset pass PTX over auto-count timing loop to display new custom ID)(rclaps.com)PTX Number SET ONE  "Flash" (1 to 10)   ID: 1 = 4961721         2 = 3519622         3 = 6091953         4 = 5640314         5 = 4572215         6 = 7531106         7 = 2351957         8 = 2688158         9 = 3073479         0 = 5564690PTX Number SET TWO  "Flicker-Flash" (1 to 10)   ID: 1 = 9887001         2 = 7621202         3 = 6000513         4 = 8110984         5 = 5843805         6 = 8087916         7 = 4748687         8 = 6099608         9 = 5781589         0 = 9577130PTX Custom / Cloned ID Number:displayed by a "Constant Flicker-Flash"PTX Personal Transponder - system 2, 3 and 4 compatibleInstructions for PTX-20, PTX-20 Custom / Cloned & ‘Enhanced’ ‘Enhanced’  -  the ID is selectable from Number SET ONE or SET TWO /option  †  SET TWO /option  "2Flash-Flash" (1 to 10)   ID: 1 =          2 =          3 =          4 =          5 =          6 =          7 =          8 =          9 =          0 = /       Tel/Fax: (UK) 0870 1624955    Email: support@team-mrt.com    Website: www.team-mrt.com   PTX ordering: www.rclaps.com   ver 1.5MRT PTX Direct Powered Transponder SpecificationsPTX Installation and MountingIt is recommended that the PTX should be fitted flat to the chassis ina horizontal position clear of ‘signal strength reducing’ obstructions.The transponder orientation is important because maximum effective'height from loop' operation is from the top and bottom of the PTX.The PTX should be mounted securely in a safe location which is notadjacent to electrical or radio equipment, or components/wiring etc.A safe location must be away from heat and vibration, it should alsobe a position that is well away from potential impact/crash damage.PTX Power Lead Replacement: remove base screws, fit new lead.MODEL RACING TECHNOLOGY    258 Dover Road, Folkestone,      Kent, England.  CT19 6NSCompliance statement (part 15.19)This device complies with part 15 of the FCC Rules.Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and(2) this device must accept any interference received, includinginterference that may cause undesired operation. FCC ID: RDVPTX1Warning (part 15.21)Changes or modifications not expressly approved by the party responsible for compliancecould void the user’s authority to operate the equipment.Stored ID numbers: 20 +1 (custom / cloned)Case: 22 x 15 x 7mm, waterproof / fuelproof (’hard case’)Mounting options: 3-hole ‘tab base’ or direct fitting (no tabs)Weight: 3g approx. (without power lead fitted)Temperature range: 0°-50°C (32°-122° F)Power feed: from free Rx channel (‘Ch3’) / 'Batt' (or battery)Power lead length: standard 190mm (approx. 7.5 inch)Connection plug: standard servo plugOperating voltage: 6V DCPower consumption: approx 7.5mA @ 6VDCDisplay LED: standard Blue ‘2flash’ / ‘flash’ / ‘flicker-flash’Signal transfer: magnetic induction

Navigation menu