Monte Carlo Fan Company 5Ahr60 Users Manual

5AHR60 5AHR60RBD

5AHR60 to the manual 7ad93598-f12f-4fd8-8212-8726302a3b2f

: Monte-Carlo-Fan-Company Monte-Carlo-Fan-Company-5Ahr60-Users-Manual-557527 monte-carlo-fan-company-5ahr60-users-manual-557527 monte-carlo-fan-company pdf

Open the PDF directly: View PDF .
Page Count: 6

Quality Ceiling fans

Owner’s

Manual

Ceiling Fan Installation Instructions

For 5AHR60 Series Fans

READ AND SAVE THESE INSTRUCTIONS

Total fan weight with

light kit included

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-

1999), including fire-rated construction.

Use this unit only in the manner intended by the manufacurer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on

one side of the outlet box and ungrounded conductor on the other side of the outlet box.

Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being

switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,

to the service panel.

Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from

the floor to the trailing edge of the blade.

WARNING – Risk of fire, electric shock, or personal injury, The fan in this box may be either directly supported from a structural framing mem-

ber of a building and/or may be mounted to an outlet box marked acceptable for fan support of 31.8 kg. (70 lbs.) or less. Most outlet boxes

commonly used for the support of luminaires may not be acceptable for fan support and may need to be replaced. Consult a qualified electrician

if in doubt.

Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

NEVER place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equip-

ment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American

Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched

on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the

service panel.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

Installation

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS

SAFETY TIPS

TTOOOOLLSSRREEQQUUIIRREEDD

PPhhiilllliippss SSccrreewwddrriivveerr WWiirree CCuutttteerrss PPlliieerrssSStteepp LLaaddddeerr

Before you begin installing the fan, Switch

power off at Service panel and lock service dis-

connecting means to prevent power from being

switched on accidentally. When the service dis-

connecting means cannot be locked, securely

fasten a prominent warning device, such as a

tag, to the service panel.

Warning-Risk of fire, electric shock, or person-

al injury. The fan in this box may be either

directly supported from a structural framing

member of a building and/or may be mounted

to an outlet box marked acceptable for fan sup-

port of of 31.8 kg (70 lbs) or less. Most outlet

boxes commonly used for the support of lummi-

naires may not be acceptable for fan support

and may need to be replaced. Consult a quali-

fied electrician if in doubt.

21 OUTLET BOX METHOD

Remove Safety bar from mounting bracket by

loosing screws, sliding bar to side, and lifting it

off the 2 screws.

3

Secure mounting plate directly to a joist from

the buliding structure via the two knock out

holes on the outlet box. Use only the appropri-

ate wood screws and washers included with

your fan. Caution: Wood screws must go

through into the building joist.

5

Outlet box

Mounting

Plate

Wood

Screws

BUILDING STRUCTURE METHOD

Remove the 4 screws attaching the Mounting

neck the mounting plate. Retain the 4 screws

for re-assembly.

4

Install the mounting Plate to approved fan

brace and box combination use only the hard-

ware provided with the fan brace and box.

6FAN BRACE AND BOX METHOD

While lifting upward on the arch arm assembly tighten

the 2 set screws next to each cross pin where archs

attach to the fan housing. These set screws can be

loosened and adjusted once fan is in final position on

the ceiling.

Align hole in arch arm and hole in tab the fan

housing. Do this for each of the 3 arch arms.

Install Keeper pin into all 3 cross pins.

Install 3 screws to hold glass to fan housing.

Do not overtighten as this could crack the

glass.

Install and tighten set screws for each arch leg

located on the yoke.

10

15

12

13

Spread 3 arch arms outward and place over the

tabs on fan housing. Make sure the arm with

the electrical connection plugs is next to the

plugs on the fan housing.

11

14

Lower upper glass disk onto fan housing and

align 3 holes in glass with 3 holes in fan hous-

ing.

9

Lift mounting neck to mounting Plate and align

screws.

7

Secure mounting neck to the mounting plate

with four screws to become a complete mount-

ing bracket.

8

Loosen the 2 downrod set screws to allow

downrod intallation to the yoke.

Plug in electrical connection from Arch assembly

to the fan body. Install canopy and yoke cover over the down-

rod.

16 17 18

Make wire connections as per above diagram.

Connect the white wire from the fan to the

White or Neutral wire from the power source.

Connect the black wire from the fan to the

Black or hot wire from the power source.

Connect all Green / Yellow wires from the fan,

Downrod and mounting bracket to the Ground

wire from the house.

26

For Canadian installation in both flush and

downrod mode the safety cable must be

installed into the house structure beams using

the 3” lag screws provided. Make sure that

when the safety cable is fully extended the

leadwires are longer than the cable and no

stress is placed on the leadwires.

24 Canadian mounting only

Safety Cable

Lag Screw

Make wire connections to power source using

wire nuts provided. Make sure that no filiments

are outside of the wirenut. After making the

wire connections, the wires should be spread

apart with the grounded conductor and the

equipment-grounding conductor on one side of

the outlet box and ungrounded conductor on

the other side of the outlet box.

25

House Fan

Black

White

Green

Black

White

Green(downrod)

Green(Bracket)

Install 6x15 Watt candelabra bulbs included.

22

Hang assembled fan from the mounting bracket

installed to ceiling in previous step. Make sure

the fan is hanging straight. Rotate fan until the

tab on the Mounting bracket engages the slot

on the Downrod Ball. This must be done to

prevent the fan body from rotating when the

blades are in motion.

23

Re-install safety bar removed in step. 3 by

placing safety bar on screws, sliding into place,

and tightening the 2 screws.

27

Tread leadwires and safety cable through the

downrod.

Place downrod into the yoke, align the holes in

the yoke with the holes in the downrod and

install cross pin. Install keeper pin into cross

pin.

19 20

Tighten set screws to hold downrod securely in

the yoke. Drop cover over yoke.

21

Place floating brackets onto blades aligning

holes in blade with the floating bracket. Place blade arms onto the other side of the

blade and aligning holes. Insert screws with

fabric washers though the holes and tighten

securely.

Remove motor screws from fan motor and save.

28 29 30

Find the glass retainer with visible screw. Loosen the

screw and tip the retainer to the side. Next lift glass

and place the glass edge into the remaining glass

retainers. Then lift the other side of the glass upward

and tip the loosened glass retainer downward to

engage the glass. Retighen the glass retainer screw.

Install the 2x50 watt halogen bulbs. Do not

touch bulb surface as oily residue from skin can

cause the bulb to explode.

Install all 5 fan blade assemblies to the motor

as shown above. Tighten screws securely.

Loosen 3 of the 4 screws that will hold the light

kit pan. Remove the screw that is associated

to the closed hole on the light kit pan as shown

in the inset.

Lift light kit pan to the fan motor assembly.

Align the 3 screws with the key hole slot holes

in the light kit pan (see inset). Rotate the light

kit pan as shown. Then install the screw

removed in the previous step though the closed

hole. Tighten all 4 screws securely.

3132 33

34 35

Install wall control unit to outlet box

using machine screws provided.

40

Lift Canopy to ceiling aligning the key hole slots

with the screws on the bottom of the Mounting

bracket. Rotate the canopy Counter Clockwise

to lock in place. Tighten the screws to secure

the Canopy. See inset for Keyhole shape

37

Attach front cover to wall control

with screws provided.

41

Set dip switches on the Remote Transmitter and Remote

Receiver to the same settings. This must be done so the

units will communcate properly. If you have other fans you

can set to control from one transmitter by setting both

receivers the same as the transmitter. If you have more

than one fan with remote. You can set the dip switches to

different positiosns to have seperate control.

Remote Transmitter Dip swtiches

Remote Receiver Dip switches

36

Remove cover by snaping off from

top or bottom. Install 12V battery

into wall remote. Duracell MN21 /

Eveready A23 / GP 23A all 12V.

38

Attach cover of remote by placing

over buttons and snaping into place.

39

To control fan speed select from High, Medium

or low speed buttons. To turn the fan off press

the Fan on / off button. To dim upper lights

press and hold U/L botton. To dim Lower lights

press and hold D/L button. To turn off either

up or down light press and quickly release

either U/L or D/L button. Press button marked

REV to reverse the rotation direction of the fan

blades

Fan speed

control but-

tons

Fan on / off

Light dim-

mer for up

and down

lights

Fan

reverse

button

42

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

3.Check to make sure the dip switches from the transmitter and receiver are set on the

same frequency.

CAUTION: Make sure main power is turned off.

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each

other or against the interior wall of the switch housing.

CAUTION: Make sure main power is turned off before entering switch housing.

4.Some fan motors are sensitive to signals from Solid State variable speed controls. DO

NOT USE a Solid State variable speed control.

5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear

after this period.

1.Make sure that the ridge of the canopy engages the notch in the downrod ball.

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor.

4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box

and junction box is mounted firmly to ceiling joist.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of one of the blades. Measure this distance

from blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade is

positioned for measurement. Repeat for each blade. If all blade levels are not equal, you can

adjust blade levels by the following procedure. To adjust a blade tip down, insert a washer

(not supplied) between the blade and blade holder at the screw closest to the motor. To

adjust a blade tip up, insert washer (not supplied) between the blade and blade holder at

the two screws farthest from the motor. Reverse the position of the washer if blades mount

from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can

redistribute the weight and possibly result in smoother operation.

1.Check wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

CAUTION: Make sure main power is turned off before entering switch housing.

2. If fan sounds noisy:

1. If fan does not

start:

3. If fan wobbles:

4. If light does not

work:

Trouble Shooting

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation,

or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,

please check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty

in installation, please call our Customer Service Center at the number printed on your parts list insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service dis-

connecting means to prevent power from being switched on accidentally. When the service dis-

connecting means cannot be locked, securely fasten a prominent warning device, such as a tag,

to the service panel.

Customer Service Center:

740 S.W. Loop 820, Suite 110

Fort Worth, Texas 76115

1-800-519-4092