Morcom AE1800 Dual Frequency Navtex Receiver User Manual AE 1800 REF Manual Draft

Morcom International, Inc. Dual Frequency Navtex Receiver AE 1800 REF Manual Draft

User Manual AE1800

AE–1800 Instruction Manual UM–AE1800–1.0 First Edition January, 2008                                                    ALDEN NAVTEX RECEIVER MODEL AE–1800                    INSTRUCTION MANUAL
AE–1800 Instruction Manual WARRANTY WARRANTY  MORCOM International, Inc. (MORCOM) warrants the AE–1800 NAVTEX Receiver and its active antenna ANT–2000 against defects in materials and workmanship for a period of one year from the date of shipping from the factory, during which time MORCOM will, at its option, either repair or replace the products that prove to be defective.  Users shall ship defective products, freight prepaid, back to a specified MORCOM dealer for warranty service.  The warranty shall not apply to defects caused by:  ●  Misuse or incorrect usage ●  Static discharges/lightning strikes to the antenna or to the receiver or other types of natural disaster ●  RF power from radio transmitters in excess of 30V RMS at the antenna input ●  Improper or inadequate maintenance by the user ●  Unauthorized service including modification, realignment of the receiver/antenna ●  User–supplied software or interfacing ●  Operation outside the environmental specifications listed in the manual, or ● Improper installation  The above warranty applies to the original user with a proof of purchase.  Before returning the unit to your MORCOM dealer for warranty service, please obtain MORCOM’s return authorization.  When shipping the unit to your dealers for service, please be sure to include the following types of information:  ・ Serial number ・  Software release date and revision (REV.) number ・  Power supply voltage ・  Installation details, including antenna height and surrounding environment ・  Detailed description of trouble ・  Valid proof of purchase from authorized MORCOM dealer         MORCOM International, Inc.   3656 Centerview Drive, Unit #1   Chantilly, VA 20151 – U. S. A.  PHONE: (703)263–9305  FAX: (703)263–9308  www.morcom.com
AE–1800 Instruction Manual IIMPORTANT NOTES IMPORTANT NOTES  1. RADIO FREQUENCY INTERFERENCE  This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when this equipment is operated in a commercial environment.    This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.  Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense.   2. PURPOSE OF THIS MANUAL  The purpose of this manual is to help the user operate and maintain the equipment. The information provided is not to be considered as a contractual specification.   3. USER’S RESPONSIBILITY                                                              The Alden Model AE–1800 NAVTEX Receiver obtains data transmitted from Government facilities. MORCOM International Inc. (MORCOM) makes no claim as to the accuracy, completeness or currency of the data since the AE–1800 only provides a means of receiving the data. Users are completely responsible for verifying the correctness and currency of all data received, and MORCOM shall not be liable to users for any loss, damage or liability caused directly or indirectly by such use. Users are solely responsible for action taken or not taken as a result of the reception or non–reception of data.        MORCOM International, Inc.   3656 Centerview Drive, Unit #1   Chantilly, VA 20151 – U. S. A.  PHONE: (703)263–9305  FAX: (703)263–9308  www.morcom.com
AE–1800 Instruction Manual WARNINGS < WARNINGS >   1.   INSTALLATION & OPERATING ENVIRONMENT THE DISPLAY CABINET IS IN THE “PROTECTED” EQUIPMENT CATEGORY AS DEFINED UNDER IEC 60945(2002), AND IS NOT WEATHERIZED FOR OUTDOOR INSTALLATION/OPERATION. ANY DAMAGE CAUSED DIRECTLY OR INDIRECTLY THROUGH WATER INTRUSION IS NOT COVERED BY THE MANUFACTURER’S OR DEALER’S WARRANTY.    2. INSTALLATION & OPERATING PROCEDURES ANY DAMAGE CAUSED BY INSTALLING OR OPERATING THE EQUIPMENT OUTSIDE THE SPECIFICATIONS DESCRIBED IN THIS MANUAL IS NOT COVERED BY THE MANUFACTURER’S OR DEALER’S WARRANTY.  CONTACT YOUR DEALER FOR WARRANTY CONDITIONS.    3. LIABILITY ● OPERATION NEITHER THE MANUFACTURER NOR ITS DEALER IS RESPONSIBLE FOR ANY LOSS OF LIFE, PERSONAL INJURY OR DAMAGE TO THE PROPERTY RESULTING FROM THE USE OF THIS EQUIPMENT OR FROM BEING, FOR ANY REASON, UNABLE TO EITHER OPERATE THE EQUIPMENT OR RECEIVE INTENDED NAVTEX MESSAGES.  ● MANUAL REASONABLE PRECAUTIONS HAVE BEEN TAKEN TO PREPARE THIS MANUAL. HOWEVER, NEITHER THE MANUFACTURER NOR ITS DEALER ASSUMES ANY RESPONSIBILITY FOR ERRORS OR OMISSIONS.
AE–1800 Instruction Manual CAUTIONS < CAUTIONS >  1: Operational – Memory Retention Period Do not leave the equipment switched off for more than 10 days continuously, or all stored messages will be erased, whether they are protected or not. Important messages you wish to preserve should be output to an optional printer or to a PC via an appropriate rear panel interface connector if the unit is to be kept turned off for extended periods of time.  2:  Operational – “Memory–Full” Indication As soon as the equipment has stored a total of 199 messages, the following caution will show up in the bottom command/prompts line along with 3 beeps:  MEMORY FULL !    [CLR] TO ACKNLG.  The oldest message will then be erased from memory automatically after reception of a next new message. As soon as you notice the above warning, be sure to acknowledge each unread message by pressing  , and if necessary, press to protect important messages you wish to retain for permanent storage.  3: Environmental Safety – Equipment Disposal The display cabinet and the active antenna unit are considered environmentally safe in their original, assembled forms. However, if either unit is to be discarded for any reason, be sure to follow all relevant local ordinances/regulations, and contact your dealer or the manufacturer (contact information given below) for assistance or instructions before disposing of it. Do not destroy the cabinet or the antenna casing.         MORCOM International, Inc.   3656 Centerview Drive, Unit #1   Chantilly, VA 20151 – U. S. A.  PHONE: (703)263–9305  FAX: (703)263–9308  www.morcom.com
AE–1800 Instruction Manual Index  1. Typical NAVTEX Message Screen.............................................................1-1 1.1. Introduction........................................................................................................1-1 1.2.  Indication of Reception and Storage of New NAVTEX Message......................1-6 2.  Control Panel Functions .........................................................................2-1 3. Basic Operating Procedure.......................................................................3-1 3.1. Introduction........................................................................................................3-1 3.2. Turning the Equipment On/Off.........................................................................3-1 3.3. Adjusting Screen Brightness ...........................................................................3-2 3.4.  Adjusting Keypad Backlighting Level ..............................................................3-2 3.5.  Switching First and Second Receivers..............................................................3-2 3.6. Scrolling NAVTEX Messages.............................................................................3-3 3.7. Stopping Audible and Visual Alarm ..................................................................3-4 3.8. Protecting Messages for Permanent Storage....................................................3-5 3.8.1. Introduction..............................................................................................3-5 3.8.2. Protecting Procedure ..............................................................................3-5 3.8.3.  Removing Protection Tag ......................................................................3-6 4.  Customizing Operation via Menu System...................................................4-1 4.1. Introduction........................................................................................................4-1 4.2. Accessing the Menu System ..............................................................................4-1 4.3. Selecting Screen Background Colors ................................................................4-2 4.4. Selecting Message Font Types...........................................................................4-2 4.5.  Turning on/off Screen Sleep Mode.....................................................................4-3 4.5.1. Introduction..............................................................................................4-3 4.5.2.  Turning Sleep Mode on ............................................................................4-3 4.5.3.  Setting Times to Reduced Brightness Levels ......................................4-4 4.6. Selecting Frequencies for Second Receiver.......................................................4-4 4.7. Turning on/off Keypress Beep ...........................................................................4-5 4.8.  Selecting and Rejecting Transmitters...............................................................4-6 4.8.1. Introduction .............................................................................................4-6 4.8.2. Setting Procedure ...................................................................................4-6 4.9.  Selecting and Rejecting Message Types............................................................4-8 4.9.1. Introduction.............................................................................................4-8 4.9.2. Setting Procedure..................................................................................4-8 4.10. Searching Memory for Stored Messages......................................................... 4-11 4.11. Selecting Output Messages .............................................................................4-12
AE–1800 Instruction Manual Index  4.11.1. Introduction ............................................................................................4-12 4.11.2.  Outpu t t ing Live NAVTEX Messages................................................4-13 4.11.3.  Outputting All Stored Messages .......................................................4-14 4.11.4.  Outputting NAVTEX Messages of Specific Receiver ....................4-15 4.11.5.  Outputting NAVTEX Messages of Specific Station ......................4-16 4.11.6. Outputting NAVTEX Messages of Specific Message Type...........4-17 4.11.7.  Outputting All Displayed NAVTEX Messages ...............................4-18 4.11.8.  Outputting Specific NAVTEX Message...........................................4-19 4.12. Setting Output Ports .......................................................................................4-20 4.12.1. Introduction ..........................................................................................4-20 4.12.2.  Enabling/ Disabling I / O Ports .............................................................4-20 4.12.3. Selecting Communications Protocols ...........................................4-22 4.12.4. Selecting Bit Formats and Data Transfer Rates ......................4-23 4.13. Performing Self–Diagnostic Tests ..................................................................4-26 4.13.1. Introduction ............................................................................................4-26 4.13.2.  Activating Self–Diagnostic Test Function.........................................4-26 4.13.3. Checking Test Results .............................................................................4-27 4.14. Turning on/off Message Alarms.......................................................................4-28 4.15. Resetting the System......................................................................................4-29 5. User–Level Troubleshooting .....................................................................5-1 5.1. Power–Up Problems...........................................................................................5-1 5.2. No Message Reception .......................................................................................5-2 5.3. Message Storage Problems................................................................................5-4 5.4. Poor Reception ...................................................................................................5-5 5.5. Blank Message Screen.......................................................................................5-6 5.6. Uncontrollable Screen Brightness.....................................................................5-6 5.7.  No Beep from Keypress .....................................................................................5-6 5.8. No Response from Keypress ..............................................................................5-7 5.9. No Message Alarm Indication ...........................................................................5-7 5.10. No Message Alarm Output ................................................................................5-8 5.11. No External Outputs .........................................................................................5-8 5.12. External Control Problem .................................................................................5-9 6.  User–Level Maintenance Instructions ................................................6-1 6.1.  Maintenance on the Equipment Cabinet..........................................................6-1 6.2.  Maintenance on Electrical Connections............................................................6-1 6.3.  Maintenance on The Active Antenna Unit........................................................6-2
AE–1800 Instruction Manual Index  6.4. Self–Diagnostic Tests.........................................................................................6-2 6.5. Recommended Spare Parts................................................................................6-3 7. Installation ............................................................................................7-1 7.1. Receiver Cabinet Installation............................................................................7-1 7.1.1. General Precautions ...............................................................................7-1 7.1.2.  Mounting the Receiver Cabinet..................................................................7-1 7.2. Antenna Installation..........................................................................................7-3 7.2.1. Installation Site Requirements..................................................................7-3 7.2.2. Precautions for Cabling ..............................................................................7-3 7.3. Electrical Connections .......................................................................................7-5 7.3.1. Introduction ..............................................................................................7-5 7.3.2.  Connector Pin Assignments and Connections ....................................7-7 7.4.  INS Port Data and Command Sentences........................................................7-15 7.4.1.  Received NAVTEX Sentence Format .................................................7-15 7.4.2. Controlling Receiver Operation via INS (RS–422) Port ...............7-17 7.4.3.  Checking Current Settings via INS (RS–422) Port.......................7-18 7.4.4.  Alarm Output Sentence Formats.......................................................7-19 7.4.5. Alarm Acknowledgement .....................................................................7-20 7.4.6.  Proprietary Sentence (Switching 2nd Receiver Frequency) ........7-20 8.  Summarized Theory of Operation ........................................................8-1 8.1. What is NAVTEX?..............................................................................................8-1 8.2. Operating Frequencies ......................................................................................8-1 8.3. Service Area........................................................................................................8-1 8.4. Error Correction.................................................................................................8-1 8.5. NAVTEX Receiver – General.............................................................................8-2 8.6. The AE–1800 NAVTEX Receiver ......................................................................8-2 8.7.  Operating Principle of AE–1800........................................................................8-3 9. Specifications .........................................................................................9-1 10. List of Alarms ......................................................................................10-1 10.1. Message Alarms ...............................................................................................10-1 10.2. Operational Alarms..........................................................................................10-1 11. List of Abbreviations ........................................................................... 11-1 12. User Settings To Be Stored in Non–Volatile Memory ............................12-1 13.  List of Components To Be Shipped .........................................................13-1
AE–1800 Instruction Manual Typical NAVTEX Message Screen 1.  Typical NAVTEX Message Screen  1.1. Introduction The illustration below represents a typical NAVTEX message screen, showing a new message received on the first (518 kHz) receiver. A similar screen will show up when the equipment is switched to receive a second receiver (490 kHz or 4209.5 kHz) message. A brief description of on–screen indications is given below and in the following pages.  Figure 1-1    Typical NAVTEX Message Screen (First Receiver Page)                         ①  Indication of Receiver in Use to Display Current Messages  ・ 1ST RCVR:    First receiver, 518 kHz  ・ 2ND RCVR1: Second receiver, 490 kHz or 2ND RCVR2:4209.5 kHz   The two receivers can be switched by pressing or by means of a software command from an IBS/INS terminal via the rear panel RS–422 connector (INS port). See paragraph 7.4 for details.  ②   Message No. and Total No. of Messages Stored   The message number of the currently displayed message along with the total number of stored messages is indicated in the following format:  Examples:  ・ 12/12:  Message #12 (newest message) of 12 messages stored  ・ 1/12:  Message #1 (oldest message ) of 12 messages stored  (continued on next page) 1ST RCVR MSG (12/12)         STANDBY JD13   INEW MESSAGEIIALARM!II 011400 UTC JAN POLISH SAR INFO 003 SOUTHEASTERN BALTIC FISHING VESSEL OF UNIDENTIFIED REGISTRY IS ON FIRE AND IS IN DANGER OF SINKING IN POSITION 55–22.23N 14–40.37E. ALL SHIPS IN THE VICINITY ARE URGENTLY REQUESTED TO RUSH TO THE SITE AND OFFER ASSISTANCE. NNNN  STORED (CER= 00%)MORE NEW MSG LEFT ! ① ② ③ ④ ⑤ ⑥    ⑨     ⑩     ⑬ ⑦  ⑧      ⑪     ⑫
AE–1800 Instruction Manual Typical NAVTEX Message Screen 1.  Typical NAVTEX Message Screen (continued – 2/6)  1.1.  Introduction (continued – 2 /5)  ③  Message Scrolling Keys   The keys that can be used to manually scroll messages across the current screen are indicated.  ・  :  Line–by–line scrolling by pressing /  ・ :  Message–by–message scrolling by pressing/   NOTE: When a type–D message (SAR, piracy and armed robbery information) is received on either the first or second receiver, automatic scrolling will be disabled until the user acknowledges the message withor with a software command from an IBS/INS terminal via the rear–panel RS–422 connector. See paragraph 7.4 for details.  ④ Receiver Operating Status Indication  The current status of receiver operation is indicated here.  ・ ABORTED:  The receiver has failed to lock onto the current transmission, due, for example, to weak signal level or noise interference. No message will be displayed or stored.   NOTE: Signal propagation conditions change greatly with time. You might not be able to receive a signal in the daytime that can be received at night; this is normal and should not be considered as a sign of receiver malfunction.  ・ ACQUIRING:  The receiver is currently in the process of locking onto the start of the current message transmission.  ・ LOCKED:  The receiver has locked onto current NAVTEX transmission, allowing a message to be received. As soon as the equipmet starts receiving the message, this indication will be replaced by RCVNG MSG.  ・ RCVNG MSG:  The receiver is properly receiving a message after locking onto current transmission. This blinking indication will stay until the end–of–message code NNNN (⑩) is received.      NOTE: Whether to display or output the message to external devices depends on the character error rate (CER,  ⑫) and on the selection/rejection settings to be made via the procedure in paragraph 4.8.  ・ STANDBY:  The receiver is idling, waiting for a NAVTEX message transmission to begin. Most stations transmit messages every 4 hours. ⑤  Operating Status Line   The current status of receiver operation, text scroll keys, etc. are indicated here.  Examples:  ・ 1ST RCVR MSG:   Message received on the first receiver is currently displayed.  ・ 2ND RCVR MSG: Message received on the second receiver (490 or 4209.5 kHz) is currently displayed.  ・  :  Message can be scrolled line by line by pressing /.  ・ STANDBY:  Receiver is idling, waiting for a NAVTEX message transmission. See  ④  above for details. (continued on next page)
AE–1800 Instruction Manual Typical NAVTEX Message Screen 1.  Typical NAVTEX Message Screen (continued – 3/6)  1.1.  Introduction (continued – 3/5)  ⑥  Message Identification (Message ID)   The ID of the currently displayed message is shown here. A red–colored ID represents a warning message. A message ID consists of the following elements: station ID, message type, and message serial number, as in the following example.    Figure 1-2    NAVTEX Message ID Format – Example         *1: ID of the transmitter from which the message was received.  Examples: J in NAVAREA  Ⅰ:  Gislövshammar, Sweden  F in NAVAREA  Ⅳ:  Cape Cod /Boston, U.S.  I in NAVAREA  Ⅱ:  Las Palmas, Spain  *2: Type (category) of this message ( subject indicator)  Examples: A: Navigational warnings  B: Weather warnings  D: Search and rescue, piracy and armed robbery information  *3: Serial number of this message  Each message within the same category group is allocated a serial number between 00 and 99 by each transmitter. A message with number 00 is always received on each transmission regardless of rejection settings, and will be displayed and stored in memory. ⑦ Alarm Tag IIALARM!III  This tag represents a visual alarm and is turned on when a NAVTEX message of one of the following types has been received.  ・ Type–A Message: Navigational warning (initially disabled)  ・ Type–B Message: Weather warning (initially disabled)  ・ Type–D Message: Search and rescue, piracy and armed robbery information. All text characters will be displayed in red to distinguish it from other type alarm messages.  ・ Type–L Message: Additional navigational warning (initially disabled)   NOTE: When a type–D message has been received, an audible alarm will also be turned on, beeping at approx. 1–second intervals. To silence the alarm sound, press . A second keypress resets the alarm and removes the alarm tag.    The alarm for the message types A, B and L is initially disabled. It can be enabled via SYSTEM MENU – 9:TURN ON /OFF MESSAGE ALARM. See paragraph 4.14 for details.  (continued on next page) Silencing the audible alarm constitutesyour acknowledgement of the currentalarm message. < CAUTION > J  D  1  3 *3Message serial number  (B3 & B4 characters) *2Message Type  (B2 character) *1Transmitter ID  (B1 character)
AE–1800 Instruction Manual Typical NAVTEX Message Screen 1.  Typical NAVTEX Message Screen (continued – 4/6)  1.1.  Introduction (continued – 4 /5)  ⑧  New Message Tag IINEW MESSAGEII   This indication ( tag) shows that the currently displayed NAVTEX text is a new message that you have not yet read or acknowledged.    To acknowledge it, simply press   or , turning the tag off.    If two or more new messages have been left unread, the following caution message will be displayed at the screen bottom, prompting you to read them. Press  again to display, or scroll the text up to, the next one by pressing  /.     The NEW MESSAGE tag for the current message will be automatically removed 24 hours after its reception, if it is left unacknowledged (i.e. if  is not pressed).  ⑨ NAVTEX Message   If message text exceeds the screen display area, you can scroll it line–by–line by pressing  /. Holding down either key accelerates the scroll.   To read other messages, press / ( for message–by–message scrolling). Holding down either key accelerates the scroll.    Type–D messages (SAR, piracy and armed robbery information) will be displayed in red. A new type–D message will remain fixed on screen until:  ・ it is acknowledged by pressing  or by means of a *1software command through an INS/IBS terminal interfaced to the rear panel RS–422 connector, or  ・  another new type–D message is received.  *1: See paragraph 7.4.5 for details.  NOTE: Forced carriage return   When the number of characters in a line exceeds 40, an internally generated carriage return symbol, shown above, will be automatically inserted in the 40th character position to divide the last word, forcing the rest of the characters in the word to shift to the top of the next line. This symbol will be replaced by an underscore ( _ ) (hex 5F) when it is printed or output to an IBS/INS device via the RS–422 port.  ⑩ End–of–Message Indication NNNN   The appearance of these four successive N characters indicates the end of the currently displayed NAVTEX message.   NOTE: Some messages including those from Chinese stations, end with NN  ( 2 Ns) instead of NNNN ( 4 Ns), in which case, the equipment will consider that the transmission has not ended properly, and will not, therefore, display and store such a message, or will append it to a new message, if received within a specified period of time, and display the two messages combined. The RS–232C port (printer port) may be set to output such messages. See paragraph 4.9 for setting instructions.   (continued on next page) MORE NEW MSG LEFT !
AE–1800 Instruction Manual Typical NAVTEX Message Screen 1.  Typical NAVTEX Message Screen (continued – 5/6)  1.1.  Introduction (continued – 5/5)  ⑪  Indication of Message Storage Status   This indication shows whether or not the displayed NAVTEX message has been stored in the internal non–volatile memory.  ・ *1STORED:  The message has been stored.   When message reception has been completed with a character error rate (CER,⑫) of 33% or less, the received NAVTEX message together with its ID will be displayed and stored in memory, making it possible to recall it onto the screen at a later time.   If the same message is received with a lower CER on the next transmission, the previously stored message will be replaced with the new one. However, if the first message was received with a CER of 4% or less, message replacement will not take place on subsequent reception with a lower CER.  When the CER exceeds 33%, the message and its ID will not be displayed and will not be stored in memory, allowing a retransmission of the same message to be displayed and stored.  *1: If the message selection/rejection settings are made so that a particular message type is rejected from storage, this indication will not be displayed regardless of a CER being smaller than 33%. See paragraph 4.9 for the related setting instructions.  ⑫  Character Error Rate (CER) Indication  CER is the percentage ratio of the total number of corrupt characters represented by asterisks (*) to the total number of characters received in a message, including control codes (sync. signal, carriage returns, line feeds, letter/numeral shift, etc.).   If a message is received with a CER equal to or greater than 33%, the message will not be displayed and stored in memory, allowing the same message to be received again on its next transmission. No CER reading will be available on the current transmission.  See paragraph ⑪  for more information on CER.  ⑬  Message Prompt Line   This line indicates the receiver’s response for the user’s keypress or displays prompts related to reception of new or alarm NAVTEX messages on the first or second receiver, or related to message storage, like the examples below.  ・  ALARM MESSAGE RECEIVED ON 2ND RCVR  ・ MORE UNREAD ALARM *2MSG LEFT  ・ 2ND *3RCVR RECEIVED NEW MSG  ・  MORE NEW MSG LEFT  ・  STORAGE LIMIT IS REACHED  ・ MEMORY FULL !  *4 [CLR] TO *5 ACKNLG.  *2 MSG = MESSAGE,  *3 RCVR = RECEIVER  *4 [CLR] =   *5 ACKNLG = ACKNOWLEDGE
AE–1800 Instruction Manual Typical NAVTEX Message Screen 1.  Typical NAVTEX Message Screen (continued – 5/5)  1.2.  Indication of Reception and Storage of New NAVTEX Message ●  Indicating Reception of New Message – First Receiver   The equipment visually indicates the reception of a new NAVTEX message by attaching a tag (iNEW MESSAGEi) to the message ID, as in the example below.  The tag will be turned off 24 hours after reception or when you press  . Figure 1-3    First Receiver Receiving New NAVTEX Message – Example                     ●  Indicating Reception of New Message – Second Receiver   When the first receiver message screen is currently showing, the reception of a new message on the second receiver is indicated with message “ 2ND RCVR RECEIVED NEW MSG” blinking in the prompt line at the screen bottom, as in the example below. To read it, switch to the second receiver page by pressing  .  Figure 1-4    Indication of New Message Reception on Second Receiver – Example         ●  Indicating Successful Storage of New Message   When a new NAVTEX message has been received with a character error rate (CER) of 33% or less, the message will be displayed and stored in non–volatile memory together with its ID; this condition is displayed with indication “ STORED” at the end of the message together with its CER reading, as in the example above.  If the CER exceeds 33%, the currently received message will not be stored and will not be displayed. No CER reading will be available.  .................................................. NNNN  STORED (CER= 00%)2ND RCVR RECEIVED NEW MSGThis message blinks. NA28    INEW MESSAGEI CCGD5 BNW 328–06 NJ – COASTAL – SURFACE AND SUB–SURFACE DATA BUOY DEPLOYMENT 1. 60 SUBSURFACE AND 2 SURFACE MOORINGS WILL BE DEPLOYED ON LINES EXTENDING FROM 39–09.6N, 073–22.05W TO 38–55.56N, 072–50.76W AND OUT TO  ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。 NNNN  STORED (CER= 00%)Tag indicating reception of new message Message ID End–of–message indication Successful storage indication Character error readout
AE–1800 Instruction Manual   Control Panel Functions 2. Control Panel Functions  The figure below shows the control panel of the equipment. A summary description of the functions the keys provides is given below and in the following pages.  Figure 2-1  Control Panel                ①  Screen Brightness Key    Repeated pressing of this key adjusts the screen brightness in a total of 8 steps including a completely dark level. The last used level is stored in memory. The brightness level returns to its maximum on next power–up when the equipment is switched off with the level set to its minimum. See paragraph 4.5 for related information.  ② Power Key  – 1/2  Figure 2-2    Opening Message – Example This key turns the unit on/off. A first keypress turns it on, displaying an opening message like the example at right for approximately five seconds.        Figure 2-3  Power–Off Countdown Window   Keep on pressing the key until all five bars have disappeared, and then release it to completely switch the unit off. This delayed action helps prevent an accidental shutoff and resultant loss of data.   Releasing the key with at least one countdown bar showing cancels the power–off sequence. (continued on next page)                      ② ④ ⑥ ⑧ ⑩ ⑫ ⑭ ⑯ ⑰  ① ③ ⑤ ⑦ ⑨ ⑪ ⑬ ⑮ To turn the unit off, press andhold down  for 2–3 secondsuntil a power–off countdownwindow shows up as illustratedat right, indicating that apower–off sequence has started.  SHUTTING DOWN NAVTEX RECEIVERWAIT ! – – – – –  Countdown bars  WELCOME TO NAVTEX RECEIVER   SOFTWARE VER. 1.0    REV_1.1A1 DATE OCT 06, 2007 Version and date information is an example.
AE–1800 Instruction Manual   Control Panel Functions 2.  Control Panel Functions (continued – 2/12)  ② Power Key  – 2/2   After the unit is switched on, the opening message window will be replaced with another window listing the current settings of receiver control parameters, as in the example below.  Figure 2-4 Current Settings of Receiver Control Parameters – Example                         The above list will stay on for approximately 20 seconds before the message screen shows up, replacing it automatically.    To turn the list off immediately, press  or  .  ③  Keypad Dimmer Key     Pressing this key adjusts the keypad backlighting level in a total of 8 steps including a completely switched–off level.    The last used level will be stored in memory. When the equipment is switched off with the level at its minimum, the keypad will be lit at the highest level at next power–up time.  ④  Audible Monitor Key     Pressing this key allows you to audibly monitor the reception of a NAVTEX transmission. To monitor the sound continuously, hold down the key. As soon as it is released, the audible output is turned off.  (continued on next page) CURRENT SETTINGS  1:FIRST RECEIVER:  REJECTED STATIONS:   REJECTED MESSAGE TYPES:    G    I    M       NO P Q R S T U    W X Y 2:SECOND RECEIVER:  REJECTED STATIONS:   REJECTED MESSAGE TYPES:    G    I    M       NO P Q R S T U    W X Y 3:KEYPRESS BEEP:  ON 4: DISABLED MSG ALARMS:  A  B  L 5: RECEIVING MSG OUTPUT:  OFF 6: 2ND RECEIVER FREQ.: 490KHZ 7: DISPLAY SLEEP MODE:    5MIN./ 30MIN.  IPRESS [CLR]OR [ENT] TO START. Blinks in reverse video.
AE–1800 Instruction Manual   Control Panel Functions 2.  Control Panel Functions (continued – 3/12)  ⑤  Screen Page Key     Pressing this key switches the message screen between the first receiver screen page and the second receiver screen page.   For example, if the current screen is currently showing the first receiver page (i.e. 518 kHz NAVTEX message display), a first keypress changes the display to show the second receiver page (i.e. 490 kHz/4209.5 kHz message display). A second press changes it back to the first receiver page. See paragraph 3.5 for more details.  ⑥  Alarm Stop Key     The equipment will alarm you audibly through a built–in buzzer and visually by turning on an alarm tag ( iALARM! I ) in reverse video on the message screen upon reception of an important NAVTEX warning (type–D message, for example). A type–D message text will be displayed in red. See paragraph 3.7 for more details.   Pressing this key silences the audible alarm. A second key– press removes the alarm tag, resetting the alarm. Observe the CAUTION at right.   If other types of warning messages (e.g. type–A messages) were received in addition to a D–type message, pressing the key silences the audible alarm for all warnings at a time.   A new type–D message received on either the first receiver or second receiver will remain fixed on screen and will not automatically scroll until:  ・  this key is pressed *1twice to acknowledge it,  ・  the user remotely *2acknowledges it from an IBS/ INS terminal connected to the rear–panel RS–422 connector (INS port), or  ・  another new type–D message has been received on either receiver.    If more alarm messages are left unread in memory, a next alarm message will be displayed after the above keypress. However, no audible alarm will be available.  *1: A first keypress turns off the alarm sound only.  *2: See paragraph 7.4 for information on the command format.  ⑦ Up Key   ・ When a NAVTEX message is being displayed, pressing this key scrolls the message screen downward one line at a time, allowing you to view message lines hidden beyond the screen’s upper text display limit. When the newest message (e.g. 200/200) is reached, a further keypress displays the oldest one (e.g. 1/200).   Holding down the key accelerates text scrolling.   ・ When a menu is displayed, pressing this key selects vertically listed options upward. Press    after highlighting the desired option.  (continued on next page) Silencing the audible alarm constitutesyour acknowledgement of the currentalarm message/condition. < CAUTION >
AE–1800 Instruction Manual   Control Panel Functions 2.  Control Panel Functions (continued – 4/12)  ⑧ Left Key   ・  When a NAVTEX message is being displayed, a single press of this key scrolls the message text by one message forward timewise, displaying a newer message.  ・  Holding down the key accelerates the scroll.   When the screen is showing the newest message (e.g. 200/200), a further keypress returns you to the oldest message (e.g. 1/200).   ・ When a currently displayed menu has horizontally listed options, pressing this key selects (i.e. highlights) those options in a leftward direction. Be sure to press   after highlighting the desired option.     ⑨ Enter Key    ・ When a NAVTEX message is being displayed, pressing this key displays the newest message (e.g. 200/200).   ・  When a menu is being displayed, pressing this key:  - completes the selection of a desired option,  - executes the function selected or,   -  finalizes the current setting.    ⑩ Down Key    ・ When a NAVTEX message is being displayed, pressing this key scrolls the message screen upward one line at a time, allowing you to view message lines hidden beyond the lower text display limit of the screen.   ・ When the screen is showing the oldest message (e.g. 1/ 200), further keypress returns you to the newest message (e.g. 200/200).  ・ Holding down the key accelerates the scrolling.   ・  When a menu is being displayed, pressing this key selects (highlights) vertically listed options downward. Be sure to press  after highlighting the desired option.         (continued on next page)
AE–1800 Instruction Manual   Control Panel Functions 2.  Control Panel Functions (continued – 5/12)  ⑪  Message/Station Selection Key   – 1/2   ・ When the screen is showing a NAVTEX message, pressing this key displays a summary list of the transmitter IDs and message types that are currently selected as in the example below so that the equipment displays and stores messages of the selected types from the selected transmitters.   Figure 2-5    List of Currently Selected Stations and Message Types – Example                          All transmitters and most of major message types are initially selected so that the equipment will display and store those selected types of messages from all stations in the coverage area.    A particular station or a particular message type can be rejected from display or storage via the menu system. Detailed instructions are given in paragraph 4.8.   →SYSTEM MENU → 4:MAKE SEL / REJ SETTING → 1/2/3 → 1/2 →     To turn off the above lists, press   .    NOTE: Message types A (navigational warning), B (meteorological warning), D (SAR, piracy and armed robbery information) and L ( additional navigational warning) are always selected for storage in memory and output to the I / O ports, and cannot be rejected due to the relevant IMO resolutions and IEC requirements.  (continued on next page)    MEM. SELECTED STATIONS:   A  B  C  D  E  F  G  H  I  J  K  L  M N  O  P  Q  R  S  T  U  V  W  X  Y  Z   MEM. SELECTED MESSAGES: A  B  C  D  E  F     H      J  K  L  V                  Z < FIRST RECEIVER >   MEM. SELECTED STATIONS:  A  B  C  D  E  F  G H   I  J  K  L  MN  O  P  Q  R  S  T  U  V  W  X  Y  Z   MEM. SELECTED MESSAGES:A  B  C  D  E  F      H     J  K L  V   Z < SECOND RECEIVER 1 >MEM: to be stored in memory SECOND RECEIVER 1: 490 kHz SECOND RECEIVER 2: 4209.5 kHz
AE–1800 Instruction Manual   Control Panel Functions 2.  Control Panel Functions (continued – 6/12)  ⑪ Selection/Station Key  – 2/2   ・  When option “4:MAKE SEL/REJ SETTING” on the SYSTEM MENU is currently accessed for selection/rejection settings, this key selects the station or message type you specify for display and storage, and/or output to the I/O ports (RS–232C, RS–422 and I/O DATA connectors). An example of station selecting procedure is illustrated below.    Currently selected stations (SL) are shown in green. Rejected stations (RJ) are in red.   Using / and /, highlight first the ID of the station of which messages you wish to display, store, and/or output to the I/O ports, and then, specify the target device ( ME for memory, PR for RS–232C & I/O DATA, IN for RS–422). To select the currently rejected (RJ) setting on each device, press  .   See paragraph 4.8 for details.     Figure 2-6    Selecting Stations – Example                               (continued on next page) Station C is currently rejected from display and storage (ME),and from output to printer (PR). Its messages are to be outputto the INS (IN) terminal alone. To select it to display and storeits messages, press after specifying ME using/.  SYSTEM MENU 4:MAKE SEL/REJ SETTING 1:SYNCHRONIZE BOTH RECEIVERS2:FIRST RECEIVER (518KHZ)   3:SECOND RECEIVER2:FIRST RECEIVER 1:STATIONSI 2:MESSAGES  ME PR IN A:  SL SL SLB:  SL SL SLC: RJ  RJ SLD:  SL SL SLE:  SL SL SLF:  SL SL SLG: SL SL SLH:  SL SL SLI:  SL SL SL ME PR IN J:  SL SL SLK:  SL SL SLL:  SL SL SLM: SL SL SLN:  SL SL SLO: SL SL SLP:  SL SL SLQ: SL SL SLR:  SL SL SL ME PR IN S:  SL SL SL T:  SL SL SL U:  SL SL SL V:  SL SL SL W: SL SL SL X:  SL SL SL Y:  SL SL SL Z:  SL SL SL 1: STATIONS    (MEmory  PRinter  INs ) Target Devices: ME: memory PR: printer port (RS–232C) IN: INS port (RS–422)
AE–1800 Instruction Manual   Control Panel Functions 2.  Control Panel Functions (continued – 7/12)  ⑫ Right Key   ・  When a NAVTEX message is being displayed, a single press of this key scrolls the message text by one message backward timewise, displaying an older message. See NOTE below.   ・ When the oldest message ( e.g. 1/ 200) is currently displayed, further keypress returns you to the newest message ( e.g. 200/200).   ・ Holding down the key accelerates the scroll.   ・ When a menu has horizontally listed options, pressing this key selects (highlights) those options in a rightward direction. Be sure to press  after highlighting the desired option.   ⑬  New Message Key   – 1/2   ・  When a new NAVTEX message has been received and stored, a NEW MESSAGE tag is automatically attached to the message ID as in the example below to indicate that the message is new.  Figure 2-7  Indication of Reception of New Message                        ・ Pressing  removes the tag from the message ID, meaning that you have acknowledged its reception.  (continued on next page) NEW MESSAGE Tag NJ91     INEW MESSAGEI STAKDBFE/ / 211745Z AUG 06// DGPS BNW 736–06 ANNAPOLIS, MD DGPS BROADCAST SITE IS UNMONITORED AS OF 211704Z AUG 06. NAVCEN IS UNABLE TO VERIFY SIG INTEGRITY UNTIL ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ NNNN  STORED (CER= 00%)MORE NEW MSG LEFT !More new messages are left unread.Scroll to next one by further pressing or / and /.
AE–1800 Instruction Manual   Control Panel Functions 2.  Control Panel Functions (continued – 8/12)  ⑬  New Message Key   – 2/2   ・  The new message tag will be automatically removed 24 hours after reception of that message, even if you forget to acknowledge it.          ・  The above example shows that a number of new messages have been received, as indicated by the bottom line prompt “MORE NEW MSG LEFT !.” Pressing  will recall the next new message onto the screen  It can also be displayed by pressing  / (for line–by–line viewing) or /(for message–by– message viewing).   ・ If no additional new message is left in memory, further keypress will cause the following message to show blinking for a few seconds at the bottom, indicating an operational error.  Figure 2-8    Indication of All New Messages Being Acknowledged                           (continued on next page)  Removal of the iNEW MESSAGEi tagconstitutes your acknowledgement ofthe currently displayed new message. < CAUTION > NO NEW MSG LEFT !NNNN  STORED (CER= 00%)No additional new message is left in memory
AE–1800 Instruction Manual   Control Panel Functions 2.  Control Panel Functions (continued – 9/12)  ⑭  Message/Station Rejection Key   – 1/2  ・ When a NAVTEX message text is currently being displayed, pressing this key turns on a summary list of the transmitter IDs and message types that are rejected (deselected) via the *1menu system on both the first and second receivers as in the example below, and not to be displayed and stored.  Figure 2-9  List of Currently Rejected Stations and Message Types – Example                      *1:  →SYSTEM MENU → 4:MAKE SEL/REJ SETTING  Detailed instructions are given in paragraph 4.8.  *2: SECOND RECEIVER 1 = 490 kHz,    SECOND RECEIVER 2 = 4209.5 kHz   ・  The following message types are always selected; they cannot be rejected due to the relevant *3IMO resolutions and *4IEC regulations related to navigational safety:  - Type A:  Navigational Warning  - Type B:  Meteorological Warning  - Type D :  SAR ( search and rescue), Piracy and Armed Robbery Information  - Type L:  Additional Navigational Warning  *3: IMO Resolution MSC.148(77)  *4: IEC 61097–6 Ed.2   ・ A message with serial number 00 will always be displayed and stored despite rejection settings.   ・  To turn off the above lists, press either  or  . Pressing    turns the lists off and displays the SYSTEM MENU instead.  (continued on next page)   MEM. REJECTED STATIONS:       MEM. REJECTED MESSAGES:   G I M N O P Q R S T U  W X  Y < FIRST RECEIVER >  MEM. REJECTED STATIONS:       MEM. REJECTED MESSAGES:  G I M N O P Q R S T  U  W X  Y < SECOND RECEIVER *21 >MEM: not to be stored in memory SECOND RECEIVER 1: 490 kHz SECOND RECEIVER 2: 4209.5 kHz
AE–1800 Instruction Manual Control Panel Functions 2.  Control Panel Functions (continued – 10/12)  ⑭  Message/Station Rejection Key   – 2/2   ・  When option “4:MAKE SEL/REJ SETTING” on the SYSTEM MENU is currently accessed for selection/rejection settings, this key rejects the user–specified station or message type so that its messages are not to be displayed and stored in memory, not to be output to the printer port (RS–232C) or not to be output to the INS port (RS–422).     An example of station rejecting procedure is illustrated below. The status of each target device is either SL (selected) or RJ (rejected).    Figure 2-10    Rejecting Stations – Example                              ・ Using / and /, select the station ID first, specify the target device (ME, PR or IN) to which you do not wish to store or output the station’s messages, and then press  . Make sure that the status of the device changes from SL to RJ. For instance, when ME is set to the RJ status, any messages from that station will not be displayed or stored.  ・ While other menu is being displayed, pressing this key produces three quick beeps to indicate an operational error.  (continued on next page)  SYSTEM MENU 4:MAKE SEL/REJ SETTING 1:SYNCHRONIZE BOTH RECEIVERS2:FIRST RECEIVER (518KHZ)   3:SECOND RECEIVER2:FIRST RECEIVER 1:STATIONSI 2:MESSAGES  ME PR IN A:  SL SL SLB:  SL SL SLC: SL  SL SLD:  SL SL SLE:  SL SL SLF:  SL SL SLG: SL SL SLH:  SL SL SLI:  SL SL SL ME PR IN J:  SL SL SLK:  SL SL SLL:  SL SL SLM: SL SL SLN:  SL SL SLO: SL SL SLP:  SL SL SLQ: SL SL SLR:  SL SL SL ME PR IN S:  SL SL SL T:  SL SL SL U:  SL SL SL V:  SL SL SL W: SL SL SL X:  SL SL SL Y:  SL SL SL Z:  SL SL SL 1: STATIONS    (MEmory  PRinter  INs ) Target Devices: ME: memory PR: printer port (RS–232C) IN: INS port (RS–422) Station C is selected so that its messages are to be displayedand stored in memory (ME), and to be output to printer (PR) andINS (IN) terminal. To reject C so as not to display and store itsmessages, press after specifying ME using/.
AE–1800 Instruction Manual Control Panel Functions 2.  Control Panel Functions (continued – 11/12)  ⑮ Menu Key    ・ Pressing this key opens a menu termed “SYSTEM MENU,” as shown below, to customize the operation to suit your specific needs, to test the receiver performance off–line, or to reset the entire system to the initial settings. See paragraphs in section 4 for greater details.    Figure 2-11    SYSTEM MENU   ・ To turn the menu off, press  again  or   *1.   ・  A desired menu option can be selected by highlighting it with /, followed by .     ・  The functions of each option are summarized below.  1: MAKE DISPLAY SETTINGS:   Selects display background colors, turns on/off screen sleep mode, or selects message font types.  2: SELECT 2ND RECEIVER FREQUENCIES: Selects 490 or 4209.5 kHz.  3: TURN ON/OFF KEYPRESS BEEP:   Turns on/off keypress beep.  *24: MAKE SEL / REJ SETTINGS:   Selects or rejects transmitters or message types that are to be displayed and stored. output to RS–232C, I/O DATA and RS–422 ports.   5: SEARCH FOR STORED MESSAGES:  Search stored messages by station and/or message type.  6: SELECT OUTPUT MESSAGES:   Selects messages to be output externally.  7: SET OUTPUT PORTS:   Sets output ports on/off, selects protocols, formats, etc.  8: START SELF–DIAGNOSTIC TESTS:   Executes self–diagnostic tests.  *39: TURN ON/OFF MESSAGE ALARM:   Turns on/off message alarms.  *40: RESET TO FACTORY DEFAULTS:   Initializes user–made settings.   *1: Pressing this key turns the menu off and returns you to the first receiver screen.  *2: Types A, B, D and L messages cannot be rejected due to relevant IMO resolutions.  *3: Alarm for type–D messages cannot be turned off due to relevant IMO resolutions.  *4: Stored messages will not be erased from memory by executing this function.    Detailed information on each menu option is given in section 4.  (continued on next page) SYSTEM MENU  1: MAKE DISPLAY SETTINGS 2:  SELECT 2ND RECEIVER FREQUENCIES 3:  TURN ON/OFF KEYPRESS BEEP 4:  MAKE SEL/REJ SETTINGS 5:  SEARCH FOR STORED MESSAGES 6.   SELECT OUTPUT MESSAGES 7.   SET OUTPUT PORTS 8.  START SELF–DIAGNOSTIC TESTS 9:   TURN ON/OFF MESSAGE ALARM 0.  RESET TO FACTORY DEFAULTS
AE–1800 Instruction Manual Control Panel Functions 2.  Control Panel Functions (continued – 12/12)  ⑯  Store Message Key    ・ This key is used to place a specific NAVTEX message in permanent storage, thereby protecting it from being automatically erased from memory after the maximum message storage limit (200 messages for each receiver) is reached.  ・ Pressing this key attaches a “PROTECTED” tag to the ID of the message you wish to protect, and pressing   *removes the tag from the message, as in the example below. *User confirmation is required. See ⑰ below.  Figure 2-12    Attaching / Removing Message Protection Tag – Example                ・  Up to 50 messages can be protected from automatic erasure (for each of the first and selected second receivers). An attempt to protect messages beyond this limit causes an operational error, turning on the following caution message in the message prompt line (screen’s bottom line):    ・ The message storage capacity will increase by 50 to 250 messages when 50 received messages in each receiver are protected.  ⑰ Clear Key    The major functions this key provides are:  ・ *1removing message protection tag (  PROTECTEDI ) from the currently displayed protected NAVTEX message.  ・  removing new message tag ( IINEW MESSAGEII ) from a new message, and  ・  turning off all menus at a time, returning to the first receiver message page when making settings via the *2menu system.   *1:Removing the message protection tag requires your confirmation, as shown at right.  Use / to select the desired option and then press.  *2: See section 4 for more information.  KA66     PROTECTED  170520 UTC JUN 07 UNDERWATER RESEARCH  ・・・ OPERATED VEHICLE ・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・  NNNN  STORED (CER=00%)  Protection tag is attached. KA66 170520 UTC JUN 07 UNDERWATER RESEARCH  ・・・ OPERATED VEHICLE ・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・  NNNN  STORED (CER=00%)Protection tag is removed. ARE YOU SURE ? 1: NO (CANCEL) 2: YES (EXECUTE) [▲]  [▼]  [ENT] STORAGE LIMIT IS REACHED !
AE–1800 Instruction Manual Basic Operating Procedure 3.  Basic Operating Procedure  3.1. Introduction  This section describes the basic operating procedure, allowing you to operate your NAVTEX receiver from the front keypad without prior knowledge of the NAVTEX system. The functions that are available from the keypad are summarized in section 2 (Control Panel Functions). It is assumed that a specified antenna and appropriate power supply are connected to the equipment.   3.2. Turning the Equipment On/Off  To turn the equipment on, gently press   once.   Figure 3-1    Opening Message – Example An opening message like the example at right will show up and stay for approximately five seconds, indicating the model name, software version number and release date. The numbers shown are examples.  Turning Equipment Off  Figure 3-2    Power–Shutdown Countdown Window To turn the unit off, press and hold down    for two to three seconds until a power–shutdown countdown window shows up as illustrated at right, indicating that a power–off sequence has just started.   ・  Keep on pressing the key until all countdown bars have disappeared, and then release the key to completely switch the unit off. This delayed action avoids an accidental shutoff and loss of message data. ・ Releasing the key with at least one countdown bar still showing cancels the power–shutdown sequence.  Turning Opening Message Off ・  After the unit is switched on, the opening message window will be replaced with another window listing the current settings of receiver control parameters, as in the example shown in Figure 2–4.  ・  The above list will stay on for approximately 20 seconds before the NAVTEX message screen shows up, replacing it automatically.  ・  To turn the list off immediately, press   or  .  (continued on next page)  WELCOME TO NAVTEX RECEIVER   SOFTWARE VER. 1.0    REV_1.1A1 DATE OCT 06, 2007  SHUTTING DOWN NAVTEX RECEIVER WAIT ! – – –  Countdown bars
AE–1800 Instruction Manual Basic Operating Procedure 3.  Basic Operating Procedure – 2/7  3.3. Adjusting Screen Brightness ・  The screen brightness level can be changed in a total of eight steps to suit the ambient lighting condition by repeatedly pressing  . ・  To extend the service life of the LED backlighting lamps, the level can be changed in two steps automatically after a user–preset time period. See paragraph 4.5 for detailed information on the screen sleep mode. ・  The screen background is initially white. You can change it to black or blue via the instructions given in paragraph 4.3.  3.4.  Adjusting Keypad Backlighting Level ・  The keypad backlighting level can be changed in a total of eight steps to suit the ambient lighting condition by repeatedly pressing  . ・  The last used level will be stored in memory. However, if the minimum level was used last time, it will return to the maximum level on next power–up.  3.5. Switching First and Second Receivers ・  The message display initially shows first receiver page, showing the NAVTEX message received on the first (518 kHz ) receiver. ・  To display the second receiver page to show messages received on the second receiver (*490 kHz or *4209.5 kHz), press  .    A second keypress will switch the display back to the first receiver page. To externally switch the second receiver with a command via the RS–422 connector (INS port), see paragraph 7.4.6 for instructions. ・ Pressing  will also return you to the first receiver page when you are making settings via the menu system.  Figure 3-3    Switching First and Second Receivers             * Frequency Indication: ・ RCVR1 = 490 kHz ・ RCVR2 = 4209.5 kHz   See paragraph 4.6 for  instructions.  (continued on next page) 1ST RCVRMSG(15/15)IB07 210520 UTC JUN 07 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・  ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ NNNN  STORED (CER=00%)First Receiver Page 2ND RCVR1MSG(10/10)KA23 210635 UTC JUN 07 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・   ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ NNNN  STORED(CER=00%)Second Receiver Page   
AE–1800 Instruction Manual Basic Operating Procedure 3.  Basic Operating Procedure – 3/7  3.6.  Scrolling NAVTEX Messages  The displayed NAVTEX text can be scrolled line by line or down or message by message with the use of the following pairs of keys:  ・ /:  Line–by–line scrolling.  -  Pressing   scrolls the text downward, allowing more message lines hidden beyond the lower screen limit to show up. Holding down the key accelerates scrolling.   When the top line of the newest message ( e.g. 13/13) is reached, further keypress displays the last line of the oldest message (e.g. 1/13).   -  Pressing acts in the opposite way, allowing more lines hidden beyond the upper screen limit to show up. Holding down the key accelerates scrolling.   When the bottom line of the oldest message (e.g. 1/13) is reached, further keypress displays the top line of the newest message ( e.g. 13/13).  ・ /:  Message–by–message scrolling.  -  Pressingonce scrolls the text by one message timewise forward to show a next newer message, as in the example below.  Figure 3-4    Forward Message Scrolling – Example 1     -  Holding down the key accelerates the scroll speed. After the newest message is reached, further keypress displays the oldest one.  Figure 3-5    Forward Message Scrolling – Example 2     - Pressing once scrolls the text by one message timewise backward to show a next older message, as in the example below.  Figure 3-6    Backward Message Scrolling – Example – 1     -  Holding down the key accelerates the scroll speed. After the oldest message is reached, further keypress displays the newest one.  Figure 3-7    Backward Message Scrolling – Example – 2    (continued on next page) 1ST RCVR MSG 129/130 1ST RCVR MSG 130/130 1ST RCVR MSG 130/130 1ST RCVR MSG 1/130 1ST RCVR MSG 110/130 1ST RCVR MSG 109/1301ST RCVR MSG 1/130 1ST RCVR MSG 130/130
AE–1800 Instruction Manual Basic Operating Procedure 3.  Basic Operating Procedure – 4/7  3.7.  Stopping Audible and Visual Alarm Your equipment will warn you audibly and visually upon reception of a vital NAVTEX message (type–D message), such as SAR information, piracy, or armed robbery warning. An example type–D alarm message is given below, showing the visual alarm (called the alarm tag) attached to the message ID.   The ID and text are also displayed in red to indicate that the message below is a type–D alarm message, distinguishable from other alarm messages (type–A: navigational, type–B: weather, or type–L: other alarm).  Figure 3-8    Visual Alarm Indication for Type–D Message – Example               To silence the audible alarm, simply press  . If another D type message was received before the current one, its audible alarm will also be stopped. Pressing the key again will turn off the visual alarm indication (iALARM!ii, alarm tag), resetting the alarm. A type–D message will remain fixed and will not automatically scroll until it is acknowledged or until another D message is received on either receiver. NOTE: Each alarm can be acknowledged and reset individually with the appropriate software command via the RS–422 port. See paragraph 7.4.5 for details.  If additional alarm messages are left unread in memory, that condition will be indicated as in the example above. Pressing   again will recall the next unread alarm message onto the screen.   Figure 3-9    Visual Alarm Indication for Type–A Message – Example The equipment can also be set to alert you to a navigational warning (type–A message), a weather warning (type–B message) or other warning (type–L message) via the menu system described in paragraph 4.14. (continued on next page) Silencing the audible alarmconstitutes your acknowledgementof the current alarm message. < CAUTION > Visual alarm indication ( alarm tag) This can be turned off with secondpressing of  . JD36   IIALARM!ii 210500 UTC JUN 07 SEARCH AND RESCUE OPERATION UNDERWAY FOR A PASSENGER WHO WENT OVERBOARD・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ NNNN   STORED (CER=00%)MORE UNREAD ALARM MSG LEFT!This message indicatesmore alarm messages areleft unread in memory Message ID and text areshown in red also as visualalarm. KA88   IIALARM!II 270520 UTC JUN 07 BOMBING EXERCISE WILL BE CONDUCTED DAILY IN ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・Message ID alone is shown in red.
AE–1800 Instruction Manual Basic Operating Procedure 3. Basic Operating Procedure – 5/7  3.8.  Protecting Messages for Permanent Storage  3.8.1. Introduction  Initially, all stored NAVTEX messages will be automatically erased one by one from memory on a first–in–first–out basis as the equipment continues receiving new messages after the message storage capacity limit (200 messages) is reached. If you wish to protect a specific message for permanent retention in memory, proceed via the   steps given below.    Up to 50 messages can be protected across each receiver screen, and are saved in a separate area of the non–volatile memory, allowing an additional 50 new messages to be stored in each of the first receiver and the selected second receiver.  3.8.2. Protecting Procedure  Figure 3-10    Protecting a Specific Message from Automatic Erasure – Step 1   (1) Using /and/or /, display the message you wish to save. If two or more messages are being  shown, the ID of that message should be brought to the top message line, as in the example at right.   Figure 3-11    Protecting a Specific Message from Automatic Erasure – Step 2  (2) Press . This will attach a message protection tag (PROTECTED tag) to the message ID as  in the example at right, indicating that the message is now protected against automatic erasure.   NOTE: If the message you wish to protect is a new message, the NEW MESSAGE tag will be replaced with the PROTECTED tag.   Storage Limit Indication   Attempting to protect messages in excess 50 will cause the following error message to be turned on blinking in the message prompt line for a few seconds.   Message protection tag KB67   IIPROTECTEDii 211740 UTC JUN 07 DENSE FOG EXPECTED IN AREAS BOUNDED BY  ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・NNNN   STORED (CER= 00%)MORE UNREAD NEW MSG LEFT! ID of message to be saved To protect this message, press . KB67 211740 UTC JUN 07 DENSE FOG EXPECTED IN AREAS BOUNDED BY  ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・NNNN  STORED (CER= 00%)MORE UNREAD NEW MSG LEFT! STORAGE LIMIT IS REACHED !
AE–1800 Instruction Manual Basic Operating Procedure 3. Basic Operating Procedure – 7/7  3.8.3. Removing Protection Tag  The protection tag on a specific message can be removed via the following steps:  (1) Using /and/or  /, display the message from which you wish to remove the tag.  (2)  Press . This will cause the following caution window to pop up, asking you to confirm your action.        (3) Press or   to highlight option “2:YES (EXECUTE)” and then press   .  (4)  If there are more messages you wish to remove the protection tag from, repeat the above steps.          ARE YOU SURE ?1: NO (CANCEL)i 2: YES (EXECUTE)[▲]  [▼]  [ENT]
AE–1800 Instruction Manual Customizing Operation via Menu System 4.  Customizing Operation via Menu System  4.1. Introduction  The equipment should work normally with the initial factory settings. Some of the settings, such as keypress beep on/off, screen background color, rejection of certain transmitters or message types and alarm on/off, however, may be changed to suit your specific operating needs via the menu system without degrading the performance.  4.2.  Accessing the Menu System    Figure 4-1  System Menu  The menu system can be accessed by simply pressing  . The menu shown at right should then be turned on, indicating that you have activated the menu system.  To turn the menu off, press again or *1 .  *1: Pressing  returns you to the first receiver page, if you are operating on the second receiver.  Figure 4-2    Returning to Previous Menu or Directly to Message Screen                     Menu options can be selected by pressing   /, followed by   .    (continued on next page) SYSTEM MENU 1:   MAKE DISPLAY SETTINGS 2:   SELECT 2ND RECEIVER FREQUENCIES 3:   TURN ON/OFF KEYPRESS BEEP 4:  MAKE SEL /REJ SETTINGS 5:   SEARCH FOR STORED MESSAGES 6.   SELECT OUTPUT MESSAGES 7.  SET OUTPUT PORTS 8.  START SELF–DIAGNOSTIC TESTS 9:   TURN ON/OFF MESSAGE ALARM 0.   RESET TO FACTORY DEFAULTS 1ST RCVR MSG (20/20)STANDBYIA05      NEW MESSAGE  220603 UTC FOG INFORMATION AS OF220600UTC ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ NNNN  STORED (CER=00%)SYSTEM MENU1:SELECT BACKGROUND COLORS・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・0:RESET TO FACTORY DEFAULTS5:MAKE SEL/REJ SETTINGS 1:SYNCHRONIZE BOTH RECEIVERS2:FIRST RECEIVER (518 KHZ) 3:SECOND RECEIVER1:SYNCHRONIZE BOTH RECEIVERS 1:STATIONS 2:MESSAGES2:MESSAGES A: NAVIGATIONAL WARNING B: WEATHER WARNING C: ICE REPORT D: SEARCH AMD RESCUE INFORMATION,    PIRACY/ARMED ROBBERY E: WEATHER FORECAST F: PILOT SERVICE MESSAGE G: AIS H: LORAN–C MESSAGE I: AIS MESSAGE J: SATNAV MESSAGE K: OTHER ELECTRONIC NAVAID MSG L: ADDITIONAL NAV  WARNING  
AE–1800 Instruction Manual Customizing Operation via Menu System 4.3.  Selecting Screen Background Colors    Figure 4-3    Selecting Screen Background Colors  Three different colors (white, black and blue) are selectable for the text screen background. Initially the background is set to white.  The two others can be selected via the following steps:    (1) Highlight option “ 1:MAKE DISPLAY SETTINGS” by pressing /, followed by  .  (2) Select option “1:SELECT BACKGROUND COLORS” in the same manner.  (3)  Highlight the desired option with  /again, and then press  .  (4) Press  or   to return to the text screen.    4.4.  Selecting Message Font Types   Figure 4-4    Selecting Message Font Types NAVTEX messages are initially displayed in a bold font for ease of reading from a distance (2–3 meters away).  A thinner type (normal) font can be selected via the following steps.  (1)  Highlight option “1:MAKE DISPLAY SETTINGS” by pressing  / and then  .  (2) Select “2:SELECT MESSAGE FONT TYPES” in the same manner.  (3) Highlight “2:NORMAL” with  /again, and then press  .  (4) Press  or   to return to the text screen.     SYSTEM MENU 1: MAKE DISPLAY SETTINGS 2:   SELECT 2ND RECEIVER FREQUENCIES 3:   SELECT 2ND RECEIVER LANGUAGES 4:   TURN ON/OFF KEYPRESS BEEP 5:   MAKE SEL /REJ SETTINGS 6.    SELECT OUTPUT MESSAGES 7.  SET OUTPUT PORTS 8.  START SELF–DIAGNOSTIC TESTS 9:  TURN ON/OFF MESSAGE ALARM 0.    RESET TO FACTORY DEFAULTS 1: MAKE DISPLAY SETTINGS 1: SELECT BACKGROUND COLORSI 2: SELECT MESSAGE FONT TYPES 3: TURN ON/OFF SLEEP MODE 1:SELECT BACKGROUND COLORS1: WHITEI 2: BLACK 3: BLUE SYSTEM MENU 1: MAKE DISPLAY SETTINGS 2:   SELECT 2ND RECEIVER FREQUENCIES 3:   SELECT 2ND RECEIVER LANGUAGES 4:   TURN ON/OFF KEYPRESS BEEP 5:   MAKE SEL /REJ SETTINGS 6.    SELECT OUTPUT MESSAGES 7.  SET OUTPUT PORTS 8.  START SELF–DIAGNOSTIC TESTS 9:  TURN ON/OFF MESSAGE ALARM 0.    RESET TO FACTORY DEFAULTS 1: MAKE DISPLAY SETTINGS 1: SELECT BACKGROUND COLORS 2: SELECT MESSAGE FONT TYPESI 3: TURN ON/OFF SLEEP MODE 2:SELECT MESSAGE FONT TYPES 1: BOLDI 2: NORMAL
AE–1800 Instruction Manual Customizing Operation via Menu System 4.5.  Turning on/off Screen Sleep Mode  4.5.1. Introduction   Figure 4-5    Turning Screen Sleep Mode on The screen brightness initially remains at the level set by pressing   .  To extend the service life of the backlighting lamps (white *1LED lamps), a screen sleep mode can be activated, which automatically reduces the brightness level in two steps when no key is pressed for a time period defined by the user.  The sleep mode is initially turned off. To activate its function and set the time to the sleep mode, follow the steps given in the following paragraphs.  *1: Light–Emitting Diode   4.5.2. Turning Sleep Mode on  (1)  Highlight option “1:MAKE DISPLAY SETTINGS” by pressing  /, followed by  .  (2) Select “2:TURN ON/OFF SLEEP MODE” in the same manner.  (3) Select “2: ON” in the same manner.    The following options are now selectable:  1:STANDARD:  1 minute to reduced level 1, 15 minutes to reduced level 2  2:USER–DEFINED MODE:  times to reduced levels 1 and 2 are selectable in 1–minute steps. See NOTE below.  NOTE:   Reduced level 1 = approx. half maximum brightness level  Reduced level 2 = backlighting switched off  (4)  Select the desired option, and press  .  (5)  If you selected “USER–DEFINED MODE” at the above step, proceed to the next paragraph (4.5.3) for the setting instructions.  (6) Press  or   to return to the text screen.    SYSTEM MENU 1: MAKE DISPLAY SETTINGS 2:   SELECT 2ND RECEIVER FREQUENCIES 3:   SELECT 2ND RECEIVER LANGUAGES 4:   TURN ON/OFF KEYPRESS BEEP 5:   MAKE SEL /REJ SETTINGS 6.    SELECT OUTPUT MESSAGES 7.  SET OUTPUT PORTS 8.  START SELF–DIAGNOSTIC TESTS 9:  TURN ON/OFF MESSAGE ALARM 0.    RESET TO FACTORY DEFAULTS 1: MAKE DISPLAY SETTINGS 1: SELECT BACKGROUND COLORS 2: SELECT MESSAGE FONT TYPES 3: TURN ON/OFF SLEEP MODEi 3:TURN ON/OFF SLEEP MODE 1: OFF 2: ONI 2:TURN ON/OFF SLEEP MODE 1: STANDARDI 2: USER–DEFINED MODE
AE–1800 Instruction Manual Customizing Operation via Menu System 4.5.3. Setting Times to Reduced Brightness Levels    Figure 4-6    Setting Times to Reduced Brightness Levels  If you wish to set the times to the reduced brightness levels, follow the steps given below.   (1)   Select option “2:ON.”  (2)   Select option “USER–DEFINED MODE.”  (3)  Highlight option “1:TIME TO BRT LEVEL 1” by pressing /.  (4)  Select the desired time period in one–minute steps by pressing/.  (5)  Highlight option “2:TIME TO BRT LEVEL 2” by pressing  /.  (6)  Select the desired time period in one–minute steps in the same manner.   4.6.  Selecting Frequencies for Second Receiver    Figure 4-7    Selecting Second Receiver Frequencies The following two frequencies are selectable for the second receiver’s operation:  ・ 490 kHz ・ 4209.5 kHz  Initially the second receiver is set to 490 kHz. Several countries, including  Canada, France, Portugal and U.K., are currently broadcasting national language messages on this channel, catering mainly for local users. The NAVTEX service on 4209.5 kHz is primarily intended for users in tropical regions. This shortwave frequency can be chosen via the following steps:  (1)  Highlight option “2:SELECT 2ND RECEIVER FREQUENCIES” by pressing /, followed by  .  (2)  Highlight option “2: 4209.5KHZ,“and then press  .  (3) Press  or   to return to the text screen.  The above setting will be remembered until the system is reset.  SYSTEM MENU 1: MAKE DISPLAY SETTINGS 2:   SELECT 2ND RECEIVER FREQUENCIES 3:   SELECT 2ND RECEIVER LANGUAGES 4:   TURN ON/OFF KEYPRESS BEEP 5:   MAKE SEL /REJ SETTINGS 6.    SELECT OUTPUT MESSAGES 7.  SET OUTPUT PORTS 8.  START SELF–DIAGNOSTIC TESTS 9:  TURN ON/OFF MESSAGE ALARM 0.    RESET TO FACTORY DEFAULTS 2: SELECT 2ND RECEIVER FREQUENCIES1: 490KHZI 2: 4209.5KHZ 2:TURN ON/OFF SLEEP MODE 1: OFF 2: ONI 2:TURN ON/OFF SLEEP MODE 1: STANDARD 2: USER–DEFINED MODEi 2:USER–DEFINED MODE 1:TIME TO BRT LEVEL 1I 1 MIN2:TIME TO BRT LEVEL 2  15 MIN
AE–1800 Instruction Manual Customizing Operation via Menu System 4.7.  Turning on/off Keypress Beep    Figure 4-8  Turning on/off Keypress Beep  Pressing a front panel key causes the equipment to beep, indicating proper actuation of that key; this is the initial setting.  If you wish to turn off the keypress beep, follow the  steps given below.        (1)  Highlight option “2: OFF” by pressing  /, followed by  .  (2) Press  or   to return to the previous NAVTEX text screen.  The above setting will be remembered until the system is reset.                           SYSTEM MENU 1: MAKE DISPLAY SETTINGS 2:   SELECT 2ND RECEIVER FREQUENCIES 3:   TURN ON/OFF KEYPRESS BEEP  4:   MAKE SEL/REJ SETTINGS  5:   MAKE SEL /REJ SETTINGS 6.    SELECT OUTPUT MESSAGES 7.  SET OUTPUT PORTS 8.  START SELF–DIAGNOSTIC TESTS 9:  TURN ON/OFF MESSAGE ALARM 3: TURN ON/OFF KEYPRESS BEEP 1: OFF   2: ON To silence keypressbeep, select this optionand press  .
AE–1800 Instruction Manual Customizing Operation via Menu System 4.8.  Selecting and Rejecting Transmitters  4.8.1. Introduction Initially the equipment is set to *1display NAVTEX messages from all stations on the air within the coverage area, *1store those messages in memory and output them to the printer port (RS–232C), *2I/O DATA port and INS port (RS–422). There may be cases where you do not wish to display, store, or output future messages from specific transmitters that are not of your concern to your navigational needs. Carrying out the following procedure allows you to select or reject transmitters independently for message display and storage in memory, for message output to the printer port, and message for output to the INS port.  A list of the transmitters that are currently rejected from display and storage can be checked by pressing    with the message screen showing.  *1: A message will be displayed and stored in memory unless its character error rate (CER) exceeds 33%. CER is the ratio of the number of the correctly received characters to the number of corrupt characters per message. *2: The I/O DATA port (I/O DATA) outputs the same message output as the printer port.  4.8.2. Setting Procedure To reject a specific station, execute the following step–by–step instructions: (1)  Highlight option “4: MAKE SEL/REJ SETTINGS” by pressing /, and then  . This opens a submenu as shown below with the following options:    1: SYNCHRONIZE BOTH RECEIVERS:  Applies same settings to both receivers.   2: FIRST RECEIVER (518KHZ):  Makes settings for first receiver alone.  3: SECOND RECEIVER:  Makes settings for second receiver alone.  < CAUTION >  There are NAVAREAs where the same ID is shared by two transmitters, one on 518 kHz and the other on 490 or 4209.5 kHz, located in two different countries in the same service area. In such cases, choosing option “1:SYNCHRONIZE BOTH RECEIVERS” will result in unintended rejection settings on either frequency.  Figure 4-9    Making Settings for First Receiver – Step 1               (continued on next page) SYSTEM MENU 1: MAKE DISPLAY SETTINGS 2:   SELECT 2ND RECEIVER FREQUENCIES3:   TURN ON/OFF KEYPRESS BEEP 4:   MAKE SEL/REJ SETTINGS 5  SEARCH STORED MESSAGES 6.    SELECT OUTPUT MESSAGES 7.  SET OUTPUT PORTS 8.  START SELF–DIAGNOSTIC TESTS 9:  TURN ON/OFF MESSAGE ALARM 0.    RESET TO FACTORY DEFAULTS 4: MAKE SEL/REJ SETTINGS 1: SYNCHRONIZE BOTH RECEIVERS2: FIRST RECEIVER (518KHZ)i 3: SECOND RECEIVER2: FIRST RECEIVER (518KHZ) 1: STATIONSI 2: MESSAGES
AE–1800 Instruction Manual Customizing Operation via Menu System 4.8.2. Setting Procedure – 2/3  (2)  Highlight the desired option, and then press . The above example shows that you selected option “2: FIRST RECEIVER” to make settings to the first receiver alone. Another submenu will then open with the following options:  1: STATIONS:  Selects or rejects transmitters.  2: MESSAGES:  Selects or rejects message types.  (3) Select “1:STATIONS” and then press  . This will open a table listing the station IDs, their memory (ME) storage statuses, printer (PR) and INS ( IN) port output statuses, as in the example below. The status indication is either SL (selected ) or RJ ( rejected). Initially all stations are in the SL status (i.e. selected) and messages from every station will be displayed and stored in memory, output to the printer port (RS–232C connector) and output to the INS port (RS–422 connector). Figure 4-10    Making Settings for First Receiver – Step 2                 (4) Using /, highlight the station whose NAVTEX messages you wish to display and store in memory, to output to the printer port or to output to the INS port.  (5) With /, highlight the status indication ( SL or RJ) of the target device ( ME, PR or IN).  (6)  To change the status to RJ, press   and to change it back to SL, press .   The example below shows that you wish to output the messages from station B to the INS port alone, while preventing them from being displayed and stored in memory or from being output to the printer port.   Figure 4-11    Making Settings for First Receiver – Step 3        (continued on next page) 2: FIRST RECEIVER (518KHZ)1: STATIONSI 2: MESSAGES  ME PR IN A: SL  SL  SLB: SL  SL  SLC: SL  SL  SLD: SL  SL  SLE: SL  SL  SLF: SL  SL  SLG: SL  SL  SLH: SL  SL  SLI: SL  SL  SL ME PR IN J: SL  SL  SLK: SL  SL  SLL: SL  SL  SLM: SL  SL  SLN: SL  SL  SLO: SL  SL  SLP: SL  SL  SLQ: SL  SL  SLR: SL  SL  SL ME PR IN S: SL  SL  SL T: SL  SL  SL U: SL  SL  SL V: SL  SL  SL W: SL  SL  SL X: SL  SL  SL Y: SL  SL  SL Z: SL  SL  SL 1: STATIONS   (MEmory  PRinter  INs)ME PR IN ME PR IN ME PR IN A: SL  SL  SL J: SL SL SL  S: SL SL SL B:  RJ RJ SL K: SL SL SL  T: SL SL SL Not to be storedin memory Not to be output toprinter (RS–232C) To be output toINS (RS–422)
AE–1800 Instruction Manual Customizing Operation via Menu System 4.8.2. Setting Procedure – 3/3  (7)  Likewise, repeat steps (4), (5) and (6) to make the desired RJ/SL settings for other transmitter IDs.   Do not press    after setting the status with/.  (8) Press to return to the previous menu, or  to close all menus to return to the previous text message screen.   This completes the procedure for changing the display and memory storage status, printer port output status and INS port output status.  NOTE: Those settings can be externally controlled via the INS port with appropriate commands from a PC or IBS/INS device. See paragraph 7.4 for details.   4.9.  Selecting and Rejecting Message Types  4.9.1. Introduction Initially all message types are to be displayed and stored in memory, to be output to the printer port (RS–232C), I/O DATA port (I/O DATA) and to the INS port (RS–422), except for the following types: Figure 4-12    Initially Rejected Message Types G  I  M  N  O  P  Q  R  S  T  U  W  X  Y  If you wish to select some of these types for display and storage in memory or for output to the printer/INS ports, or to prevent other messages types from being stored, or from being output to the ports, follow the procedure outlined below. NOTES: (1)  Message types A (Navigational warning), B (Meteorological warning), D (SAR, piracy and armed robbery information) and L (Additional navigational warning) are always selected for storage in memory, output to the printer, I/O DATA and INS ports; these types cannot be rejected (i .e .  cannot be set to the “RJ” status). (2)  A message with serial number 00 will always be displayed and stored regardless of storage rejection settings. (3) Those settings can be externally controlled via the INS port with appropriate commands from a PC or IBS/INS device. See paragraph 7.4 for details.  4.9.2. Setting Procedure To select some of the above initially rejected message types (e.g. type G: AIS messages) or to reject additional message types, execute the following step–by–step instructions. It is assumed that the SYSTEM MENU is currently being displayed.  (1)  Highlight option “4: MAKE SEL/REJ SETTINGS” by pressing /, and then  . This opens a submenu as shown below with the following options:   1: SYNCHRONIZE BOTH RECEIVERS:  Applies same settings to both receivers.   2: FIRST RECEIVER (518KHZ):  Makes settings for first receiver alone.  3: SECOND RECEIVER:  Makes settings for second receiver alone.  (continued on next page)
AE–1800 Instruction Manual Customizing Operation via Menu System 4.9.2. Setting Procedure – 2/3  (2)  Highlight the desired option, and then press . The example below shows that you selected option “1: SYNCHRONIZE BOTH RECEIVERS”  to make the same settings for the first and second receivers simultaneously. Another submenu will then open with the following options:   1: STATIONS:  Selects or rejects transmitters.  2: MESSAGES:  Selects or rejects message types.  (3) Select “2:MESSAGES” and then press  .   This will open a table listing the message types and titles, their memory (ME) storage statuses, printer (PR) and INS ( IN) port output statuses, as in the example below. The status indication is either SL (selected) or RJ (rejected).     The statuses of the rest of the message types (M through Z) will show up one by one with repeatedly pressing of  , as in the example in Figure 4–14.  Figure 4-13    Making Same Settings for First and Second Receivers – Step 1                              ・ Destination Devices: ME: memory  PR: printer port (RS–232C)  IN: INS port (RS–422) ・ Status:  SL: selected RJ: rejected (continued on next page) SYSTEM MENU 1: MAKE DISPLAY SETTINGS 2:   SELECT 2ND RECEIVER FREQUENCIES3:   TURN ON/OFF KEYPRESS BEEP 4:   MAKE SEL/REJ SETTINGS 5  SEARCH STORED MESSAGES 6.    SELECT OUTPUT MESSAGES 7.  SET OUTPUT PORTS 8.  START SELF–DIAGNOSTIC TESTS 9:  TURN ON/OFF MESSAGE ALARM 0.    RESET TO FACTORY DEFAULTS 4: MAKE SEL/REJ SETTINGS 1: SYNCHRONIZE BOTH RECEIVERS2: FIRST RECEIVER (518KHZ) 3: SECOND RECEIVER1: SYNCHRONIZE BOTH RECEIVERS 1: STATIONS 2: MESSAGESi 2: MESSAGES(MEmory  PRinter  INs )ME   PR   IN A: NAVIGATIONAL WARNING  SL SL SL B: METEOROLOGICAL WARNING  SL SL SL C: ICE REPORT  SL SL SL D: SEARCH AND RESCUE INFORMA–  SL SL SL   TION/PIRACY AND ARMED ROBBERY E: METEOROLOGICAL FORECAST  SL SL SL F: PILOT SERVICE MESSAGE  SL SL SL G: AI S  RJ RJ RJ H: LORAN–C MESSAGE  SL SL SL  I: PRESENTLY NOT USED  RJ RJ RJ J: SATNAV MESSAGE  SL SL SL K: OTHER ELECTRONIC NAVAID MSG.   SL SL SL L: ADDITIONAL NAV. WARNING  SL SL SL NOTE: The settings for PR applyalso to the I/O DATA port.
AE–1800 Instruction Manual Customizing Operation via Menu System 4.9.2. Setting Procedure – 3/3  Figure 4-14    Checking Statuses of Other Message Types – Example                (4) Using /, highlight the message type that you wish, or do not wish, to store in memory (ME), to output to the printer port (PR) or to output to the INS port (IN). Types A, B, D and L cannot be selected at any time, and will be skipped.  (5) With /, highlight the status indication ( SL or RJ) of the target device ( ME, PR or IN). To change the status to RJ, press   and to change it back to SL, press. The example below shows that you wish to output type G messages (AIS) to the INS port alone, while preventing them from being stored in memory or from being output to the printer port.  Figure 4-15    Making Same Settings for First and Second Receivers – Step 2                   (6)  Likewise, repeat steps (4) and (5) to make the desired RJ/SL settings for other message types. Do not press    after setting the status with/.  (7) Press to close all menus to return to the previous text message screen. 2: MESSAGES ( MEmory  PRinter  INs )ME  PR   IN A: NAVIGATIONAL WARNING  SL SL SL B: METEOROLOGICAL WARNING  SL SL SL C: ICE REPORT  SL SL SL D: SEARCH AND RESCUE INFORMA– SL SL SL   TION/PIRACY AND ARMED ROBBERY E: METEOROLOGICAL FORECAST  SL  SL  SL F: PILOT SERVICE MESSAGE  SL  SL  SL G: AI S   RJ RJ SL H: LORAN–C MESSAGE  SL SL SL  I: PRESENTLY NOT USED  RJ  RJ  RJ J: SATNAV MESSAGE  SL SL SL K: OTHER ELECTRONIC NAVAID MSG.   SL  SL  SL L: ADDITIONAL NAV. WARNING  SL SL SL AIS messages are to be output to INS port alone E: METEOROLOGICAL FORECAST  SL SL SL F: PILOT SERVICE MESSAGE  SL SL SL G: AI S  RJ RJ RJ H: LORAN–C MESSAGE  SL SL SL  I: PRESENTLY NOT USED  RJ RJ RJ J: SATNAV MESSAGE  SL SL SL K: OTHER ELECTRONIC NAVAID MSG.   SL SL SL L: ADDITIONAL NAV. WARNING  SL SL SL M: MESSAGE TYPE M  RJ RJ RJ N: MESSAGE TYPE N  RJ RJ RJ O: MESSAGE TYPE O  RJ RJ RJ P: MESSAGE TYPE P  RJ RJ RJ Rest of message types partially shown by pressing 
AE–1800 Instruction Manual Customizing Operation via Menu System 4.10. Searching Memory for Stored Messages  NAVTEX messages stored in non–volatile memory are searchable by station and/or message type via the following steps.  (1)  Highlight option “5: SEARCH FOR STORED MESSAGES ” by pressing  /, followed by  . This opens a submenu with a list of all station IDs, as shown below. The wild card character (*) represents all station IDs.  Figure 4-16    Searching for Stored Messages                    (2) Using ///, select the station of which messages you wish to search for.   For example, if you wish to search for all stored messages sent from station A, highlight A . If you wish to search for messages of a specific type from all stations, highlight the wild card character (*) which represents all transmitter IDs.  (3) Press . This opens a menu listing all the message types. The wild card (*) represents all message types.  (4) Using ///, select the desired message type. If you wish to specify all message types from the station selected at step (2), highlight  *.  (5) Press . This allows all messages to be displayed that meet the conditions you set at above steps (2) and (4).    The displayed messages can be scrolled across the screen line–by–line by pressing /  or message–by–message by pressing/.    To return to the menu, press .  To  return  to  the  previous  NAVTEX                 text screen, press it once again.    Wild Card representingall stations SYSTEM MENU  1: MAKE DISPLAY SETTINGS 2:   SELECT 2ND RECEIVER FREQUENCIES3:   TURN ON/OFF KEYPRESS BEEP 4:   MAKE SEL /REJ SETTINGS 5:  SEARCH FOR STORED MESSAGESI 6.    SELECT OUTPUT MESSAGES 7.  SET OUTPUT PORTS 8.  START SELF–DIAGNOSTIC TESTS 9:  TURN ON/OFF MESSAGE ALARM 0.    RESET TO FACTORY DEFAULTS 5: SEARCH FOR STORED MESSAGES  SEARCH BY STATION Ai B  C  D  E  F  G  H  I  J  K  L  M N O P Q R S T U V W X Y  Z *   SEARCH BY MESSAGE TYPE Ai B  C  D  E  F  G  H  I  J  K  L  M N O P Q R S T U V W X Y  Z * Wild card representing all message types
AE–1800 Instruction Manual Customizing Operation via Menu System 4.11. Selecting Output Messages  4.11.1. Introduction  The NAVTEX message that is currently being received or previously received messages stored in memory can be output to external devices (e.g., a printer, an INS/IBS device) via the rear panel interface connectors (I/O ports, i.e. RS–232C, RS–422, I/O DATA). The execution of the following instructions allows you to selectively output the desired messages by specifying various parameters, such as live (on–line) or recall– from–storage mode, receiver type, transmitter ID and message type.  (1) Press  , opening the SYSTEM MENU.  Figure 4-17    Accessing Output Selection Menu                  (2) Highlight “ 6: SELECT OUTPUT MESSAGES” by pressing /, followed by  . This opens a submenu as illustrated above, with the following output mode options:    1: RECEIVING MSG:   Message currently being received   2: ALL STORED MSG:  All stored messages   3: MSG SELECTED BY FREQUENCY:  Messages selected by specifying receiver   4: MSG SELECTED BY STATION:  Messages selected by specifying transmitter   5: MSG SELECTED BY TYPE:  Messages selected by specifying message type   6: DISPLAYED MSG:  All messages currently displayed   7: SELECTED MSG:  Individual messages selected from those appearing on display  Before the desired output can be obtained, the target output connector (output port) must be enabled (set to ON) via the instructions in paragraph 4.12. Note that all ports are initially enabled unless set otherwise previously by your dealer.  NOTE: A forced carriage return () will be replaced by an underscore ( _) (hex 5F ) when it is output to an IBS / INS terminal or a printer.  SYSTEM MENU 1: MAKE DISPLAY SETTINGS 2:   SELECT 2ND RECEIVER FREQUENCIES3:   TURN ON/OFF KEYPRESS BEEP 4:   MAKE SEL /REJ SETTINGS 5:  SEARCH FOR STORED MESSAGES 6.   SELECT OUTPUT MESSAGES 7.  SET OUTPUT PORTS 8.  START SELF–DIAGNOSTIC TESTS 9:  TURN ON/OFF MESSAGE ALARM 0.    RESET TO FACTORY DEFAULTS 6: SELECT OUTPUT MESSAGES 1: RECEIVING MSGi ON IOFFI 2: ALL STORED MSG 3: MSG SELECTED BY FREQUENCY 4: MSG SELECTED BY STATION 5: MSG SELECTED BY TYPE 6: DISPLAYED MSG 7: SELECTED MSG 
AE–1800 Instruction Manual Customizing Operation via Menu System 4.11.2.  Outputting Live NAVTEX Messages  This output mode is to be activated when an optional printer is plugged in for realtime, on–line message printing or when a live NAVTEX output is required for other onboard applications.  To output live messages as they are received, follow the steps given below. Be sure to set the printer (e.g. *1PR–900) or other receiving device properly.  NOTE: A forced carriage return () will be replaced by an underscore ( _) (hex 5F ) when it is output to an IBS/INS terminal or a printer.  (1) Highlight option “1:RECEIVING MSG” on the SELECT OUTPUT MESSAGES submenu, and then press  .  (2) Press to highlight “*2ON,” and then press . Another submenu will then show up, allowing you to select the first or second receiver, as illustrated below.   Figure 4-18  Outputting Live NAVTEX Message              (3) Using /, select the desired receiver, and then press . The equipment will then start outputting live messages from the receiver selected.    The settings you made via the above steps will be stored in memory.   (4) Press  to return to the previous menu or  to return to the first receiver message screen.   *1:  Before the printer can be used, the data transfer speed through the RS–232C port must be set to 110 baud (BIT RATE: 0.11) via the instructions given in 4.12.4.2.  *2: This setting is remembered in memory. It will return to “OFF” when you execute the system reset via the instructions in paragraph 4.15.     6: SELECT OUTPUT MESSAGES 1: RECEIVING MSGi iONi OFF 2: ALL STORED MSG 3: MSG SELECTED BY FREQUENCY 4: MSG SELECTED BY STATION 5: MSG SELECTED BY TYPE 6: DISPLAYED MSG 7: SELECTED MSG Select this option with ,and then press . 1: RECEIVING MSG 1: FIRST RECEIVER (518KHZ)i 2: SECOND RECEIVER (490KHZ) Select desired receiver with/
AE–1800 Instruction Manual Customizing Operation via Menu System 4.11.3. Outputting All Stored Messages  To output all the messages stored in memory, follow the steps given below.  NOTE: A forced carriage return () will be replaced by an underscore ( _) (hex 5F ) when it is output to an IBS/INS terminal or a printer.   (1) Highlight “2:ALL STORED MSG” on the SELECT OUTPUT MESSAGES submenu, and then press  .    The stored messages will then be output one by one.  Figure 4-19    Outputting All Stored Messages                 The following window will pop up to indicate the outputting action in progress.         The window will be turned off automatically upon completion of outputting.    To cancel the action, press .  (2) Press  to return to the previous menu or  to return to the first receiver message screen.           OUTPUTTING STORED MESSAGES. TO CANCEL, PRESS [CLR]. Select this option with /,  andthen press . 6: SELECT OUTPUT MESSAGES 1: RECEIVING MSG  ON  IOFFI 2: ALL STORED MSGI 3: MSG SELECTED BY FREQUENCY 4: MSG SELECTED BY STATION 5: MSG SELECTED BY TYPE 6: DISPLAYED MSG 7: SELECTED MSG
AE–1800 Instruction Manual Customizing Operation via Menu System 4.11.4.  Outputting NAVTEX Messages of Specific Receiver  If you wish to output all NAVTEX messages received from either receiver (first or second receiver) alone, carry out the following step–by–step procedure:  NOTE: A forced carriage return () will be replaced by an underscore ( _) (hex 5F ) when it is output to an IBS / INS terminal or a printer.  (1) Highlight option “3:MSG SELECTED BY FREQUENCY” on the SELECT OUTPUT MESSAGES submenu, and then press .  This turns on another submenu with the following options, enabling you to select the desired receiver, as in the example illustrated below:   1: FIRST RECEIVER (518 KHZ):  Outputs first receiver messages.   2: SECOND RECEIVER:  Outputs second receiver messages.   Figure 4-20    Outputting Stored Messages of First Receiver – Example                 (2)  Highlight the desired option, and then press  . The following window will pop up to indicate the outputting action in progress.         The window will be turned off automatically upon completion of outputting.    To cancel the action, press .  (3) Press  to return to the previous menu or  to return to the first receiver message screen.   OUTPUTTING STORED MESSAGES. TO CANCEL, PRESS [CLR]. To derive first receiver messages frommemory, select this option with /, and then press . 6: SELECT OUTPUT MESSAGES 1: RECEIVING MSG  ON  IOFFI 2: ALL STORED MSG 3: MSG SELECTED BY FREQUENCYi 4: MSG SELECTED BY STATION 5: MSG SELECTED BY TYPE 6: DISPLAYED MSG – ALL 7: DISPLAYED MSG – SPECIFIC 3: MSG SELECTED BY FREQUENCY 1: FIRST RECEIVER (518 KHZ) 2: SECOND RECEIVER
AE–1800 Instruction Manual Customizing Operation via Menu System 4.11.5.  Outputting NAVTEX Messages of Specific Station  If you wish to output all messages received from a specific NAVTEX transmitting station, carry out the following step–by–step procedure:  NOTE: A forced carriage return () will be replaced by an underscore ( _) (hex 5F ) when it is output to an IBS / INS terminal or a printer.  (1)   Highlight option “ 4:MSG SELECTED BY STATION” on the SELECT OUTPUT MESSAGES submenu, and then press  . This turns on another submenu with a list of station IDs, enabling you to select the desired transmitter, as in the example illustrated below:   Figure 4-21    Outputting Stored Messages Received from Station D – Example                 (2) Using /, highlight the desired ID, and then press  . The following window will pop up to indicate the outputting action in progress.        The window will be turned off automatically upon completion of outputting.    To cancel the action, press .   (3) Press  to return to the previous menu or  to return to the first receiver message screen.       Select desired station ID with /,and then press . 6: SELECT OUTPUT MESSAGES 1: RECEIVING MSG    ON  IOFFI 2: ALL STORED MSG 3: MSG SELECTED BY FREQUENCY 4: MSG SELECTED BY STATIONi 5: MSG SELECTED BY TYPE 6: DISPLAYED MSG – ALL 7: DISPLAYED MSG – SPECIFIC 4:MSG SELECTED BY STATION A   B   C   iDi   E   F   G   H   I   J   K   L   M N   O  P  Q  R  S  T  U  V  W  X   Y   Z OUTPUTTING STORED MESSAGES. TO CANCEL, PRESS [CLR].
AE–1800 Instruction Manual Customizing Operation via Menu System 4.11.6.  Outputting NAVTEX Messages of Specific Message Type  If you wish to output all messages of a specific message type, carry out the following step–by–step instructions:  NOTE: A forced carriage return () will be replaced by an underscore ( _) (hex 5F ) when it is output to an IBS / INS terminal or a printer.  (1) Highlight option “5:MSG SELECTED BY TYPE” on the SELECT OUTPUT MESSAGES submenu, and then press  . This turns on another submenu with a list of message types, enabling you to select the desired message type, as in the example illustrated below:   Figure 4-22    Outputting Stored Messages of Message Type D – Example                  (2) Using /, highlight the desired message type, and then press .  The following window will pop up to indicate the outputting action in progress.        The window will be turned off automatically upon completion of outputting.    To cancel the action, press .   (3) Press  to return to the previous menu or  to return to the first receiver message screen.      6: SELECT OUTPUT MESSAGES 1: RECEIVING MSG  ON  IOFFI 2: ALL STORED MSG 3: MSG SELECTED BY FREQUENCY 4: MSG SELECTED BY STATION 5: MSG SELECTED BY TYPEi 6: DISPLAYED MSG – ALL 7: DISPLAYED MSG – SPECIFIC Select desired message type with/,and then press . 5:MSG SELECTED BY TYPE A   B   C   iDi   E   F   G   H   I   J   K   L   M N   O  P  Q  R  S  T  U  V  W  X   Y   Z OUTPUTTING STORED MESSAGES. TO CANCEL, PRESS [CLR].
AE–1800 Instruction Manual Customizing Operation via Menu System 4.11.7.  Outputting All Displayed NAVTEX Messages  If you wish to output all messages currently displayed, follow the steps given below.  NOTE: A forced carriage return () will be replaced by an underscore ( _) (hex 5F ) when it is output to an IBS / INS terminal or a printer.  (1) Highlight “ 6:DISPLAYED MSG” on the SELECT OUTPUT MESSAGES submenu, and then press  . This turns all menus off, showing the current message screen, as in the example illustrated below.  Figure 4-23    Outputting All Currently Displayed Messages – Example                                   (2) Press   to output all the displayed messages, or    to cancel the function.    The previous message screen will return automatically upon completion of the output.   KB53 020310 UTC JUL 07 IMPORTANT WARNING FOR KUSHIRO NAVTEX AREA. STATIONARY FRONT FROM 37N 115E TO 37N 120E, 37N 130E TO 36N 142E  NNNN  STORED (CER= 00%) IA27 020240 UTC JUL 07 SAR EXERCISES BY AEROPLANES, STARTING AT 2300Z TO 1800Z, DAILY FROM 30 JUN TO JUL. AREA BOUNDED BY 33-46N 134-45E, 33-46N 135-08E, 33-30N 135-22E, 33-24N-135-45E, 32-44N 135-52E.  NNNN    STORED (CER= 00%)PRESS [ENT] TO OUTPUT OR [CLR] TO EXIT All currently displayed messages will be output by pressing  Select this option with/, and then press . 6: SELECT OUTPUT MESSAGES 1: RECEIVING MSG    ON  IOFFI 2: ALL STORED MSG 3: MSG SELECTED BY FREQUENCY 4: MSG SELECTED BY STATION 5: MSG SELECTED BY TYPE 6: DISPLAYED MSG   7: SELECTED MSG
AE–1800 Instruction Manual Customizing Operation via Menu System 4.11.8.  Outputting Specific NAVTEX Message  If you wish to output a specific message out of all currently displayed messages, carry out the following procedure:  NOTE: A forced carriage return () will be replaced by an underscore ( _) (hex 5F ) when it is output to an IBS / INS terminal or a printer.  (1) Highlight “7:SELECTED MSG” on the SELECT OUTPUT MESSAGES submenu, and then press  . This turns all menus off, showing the current message screen, as in the example illustrated below.  Figure 4-24    Outputting Specific Message – Example                                   (2) Using /  , highlight the ID of the desired message as in the example above, and then press  .    To cancel the function, press   instead of . KB53020310 UTC JUL 07 IMPORTANT WARNING FOR KUSHIRO NAVTEX AREA. STATIONARY FRONT FROM 37N 115E TO 37N 120E, 37N 130E TO 36N 142E  NNNN  STORED (CER= 00%) iIA27  020240 UTC JUL 07 SAR EXERCISES BY AEROPLANES, STARTING AT 2300Z TO 1800Z, DAILY FROM 30 JUN TO JUL. AREA BOUNDED BY 33-46N 134-45E, 33-46N 135-08E,33-30N 135-22E, 33-24N-135-45E, 32-44N 135-52E.  NNNN  STORED (CER= 00%)PRESS [ENT] TO OUTPUT OR [CLR] TO EXITTo output this message, select its ID with /  and then press . Select this option with/, and then press . 6: SELECT OUTPUT MESSAGES 1: RECEIVING MSG  ON  IOFFI 2: ALL STORED MSG 3: MSG SELECTED BY FREQUENCY 4: MSG SELECTED BY STATION 5: MSG SELECTED BY TYPE 6: DISPLAYED MSG 7: SELECTED MSG
AE–1800 Instruction Manual Customizing Operation via Menu System 4.12. Setting Output Ports  4.12.1. Introduction  In order for external devices (e.g. printer, IBS/INS component) to receive live or stored NAVTEX messages properly through the desired rear panel I/O connector (RS–232C, RS–422 or I/O DATA connector), it is necessary to set the following parameters to the port selected.   Figure 4-25    Opening Submenu for Setting Output Ports  Output Port Parameters:  ・  Status (enabled or disabled) ・ Communications Protocol ・  Bit Format and Output Rate  The following instructions allow you to set these parameters as required by the data–receiving device plugged into the desired connector.   (1) Press  , opening the SYSTEM MENU.  (2) Highlight “ 7: SET OUTPUT PORTS” by pressing /, followed by . This opens a submenu as illustrated above, with the following output options:   1: SET PORTS ON/OFF:   Enables or disables desired port.  2: SELECT PROTOCOLS:  Selects protocols for desired port.  3: SET BIT FORMAT & RATE:  Sets correct bit format and data rate.   4.12.2.  Enabling/Disabling I/O Ports  4.12.2.1.  RS–232C Port  The RS–232C port is mainly intended as a printer interface, and is initially enabled so that the message types selected in paragraphs 4.11.2 through 4.11.8 will be output via this port. If, for any reason, you wish to disable it, follow the steps given below.   Figure 4-26  Selecting Output Ports for Enable/Disable Settings – 1  (1) Highlight “1:RS–232C” and press  .  (2) Using /  , highlight “OFF.”  (3) Press to complete or  to  cancel.  (4) Press  to return to the previous submenu or  to return to the first receiver text page. SYSTEM MENU 1: MAKE DISPLAY SETTINGS 2:   SELECT 2ND RECEIVER FREQUENCIES 3:   TURN ON/OFF KEYPRESS BEEP 4:   MAKE SEL / REJ SETTINGS 5:   SEARCH FOR STORED MESSAGES 6.    SELECT OUTPUT MESSAGES 7.  SET OUTPUT PORTS 8.  START SELF–DIAGNOSTIC TESTS 9:  TURN ON/ OFF MESSAGE ALARM 0.    RESET TO FACTORY DEFAULTS 7: SET OUTPUT PORTS 1: SET PORTS ON/OFF   2: SELECT PROTOCOLS 3: SET BIT FORMAT & RATE 7: SET OUTPUT PORTS 1: SET PORTS ON/OFF   2: SELECT PROTOCOLS 3: SET BIT FORMAT & RATE 1: SET PORTS ON/OFF 1: RS–232Ci    ON   OFF  2: RS–422  ON OFF 3: I/O DATA  ON OFF
AE–1800 Instruction Manual Customizing Operation via Menu System 4.12.2.2.  RS–422 Port  The RS–432 port, designed as an interface with an IBS/INS system, is also initially enabled so that the NAVTEX message types selected in paragraphs 4.11.2 through 4.11.8 will be output via this port. If, for any reason, you wish to disable it, follow the steps given below.   Figure 4-27  Selecting Output Ports for Enable/Disable Settings – 2  (1) Highlight “2:RS–422” and press  .  (2) Using /  , highlight “OFF.”  (3) Press to complete, or  to cancel.  (4) Press  to return to the previous submenu or  to return to the first receiver text page.   NOTE: The input lines to the RS–422 connector are insulated from the ship’s ground by opto–isolators.    4.12.2.3.  I/O DATA Port  The  I/O DATA port is also initially enabled so that the message types selected in paragraphs 4.11.2 through 4.11.8 will be output via this port. If, for any reason, you wish to disable it, carry out the following step–by–step instructions:   Figure 4-28  Selecting Output Ports for Enable/Disable Settings – 3  (1) Highlight “ 3:I/O DATA” and press  .  (2) Using /  , highlight “OFF.”  (3) Press to complete or  to  cancel.  (4) Press  to return to the previous submenu or  to return to the first receiver text page.   NOTE: The message outputs available from the I/O DATA port are the same as those from the printer port (RS–232C).      7: SET OUTPUT PORTS 1: SET PORTS ON/OFF   2: SELECT PROTOCOLS 3: SET BIT FORMAT & RATE 1: SET PORTS ON/OFF 1: RS–232C     ON   OFF  2: RS–422i  ON OFF 3: I/O DATA  ON OFF 7: SET OUTPUT PORTS 1: SET PORTS ON/OFF   2: SELECT PROTOCOLS 3: SET BIT FORMAT & RATE 1: SET PORTS ON/OFF 1: RS–232C     ON   OFF  2: RS–422  ON OFF 3: I/O DATAi  ON OFF
AE–1800 Instruction Manual Customizing Operation via Menu System 4.12.3. Selecting Communications Protocols  The following communications protocols are initially assigned to the three output ports described in paragraph 4.12.  ・  IEC 61162–1 (NMEA–0183 Ver. 2.0 & greater):    RS–422 Port ・ Asynchronous non–handshaking:    RS–232 Port and I/O DATA Port  Of the three ports, only the I/O DATA port can select either the IEC 61162–1 or the asynchronous non–handshaking transfer mode. If your application using that port requires the IEC 61162–1 as its protocol, follow the steps given below.  NOTE: If you wish to connect a serial printer other than the  PR–900 to the RS–232C or the I/O DATA port, be sure to turn off its hardware flow control and set it to “X–ON / X–OFF,” if available, or an erratic printout can result.  (1)  Highlight option “2:SELECT PROTOCOLS” on the SET OUTPUT PORTS submenu, and press . This turns on another submenu for selection of the protocols, as illustrated below.    Figure 4-29    Accessing Submenu for Selection of Protocols for I/O DATA Port            (2) To change the protocol for the I/O DATA port to the IEC 61162–1, press, highlighting option IEC61162, as shown below.     Figure 4-30    Selecting Protocol for I/O DATA Port (3) Press to complete the selection.      (4) Press   to return to the previous submenu or   to return to the first receiver text page.  Protocols are selectable for this port only. SYSTEM MENU 1: MAKE DISPLAY SETTINGS 2:   SELECT 2ND RECEIVER FREQUENCIES3:   TURN ON/OFF KEYPRESS BEEP 4:   MAKE SEL / REJ SETTINGS 5:   SEARCH FOR STORED MESSAGES 6.    SELECT OUTPUT MESSAGES 7.  SET OUTPUT PORTS 8.  START SELF–DIAGNOSTIC TESTS 9:  TURN ON/ OFF MESSAGE ALARM 0.    RESET TO FACTORY DEFAULTS 7: SET OUTPUT PORTS 1: SET PORTS ON/OFF 2: SELECT PROTOCOLS   3: SET BIT FORMAT & RATE 2: SELECT PROTOCOLS 1: RS–232C     IEC61162      NONE (ASCII)2: RS–422  IEC61162  NONE (ASCII)3: I/O DATAI IEC61162  NONE (ASCII)2: SELECT PROTOCOLS 1: RS–232C     IEC61162      NONE (ASCII)2: RS–422  IEC61162  NONE (ASCII)3: I/O DATAI iIEC61162i NONE (ASCII)
AE–1800 Instruction Manual Customizing Operation via Menu System 4.12.4.  Selecting Bit Formats and Data Transfer Rates  4.12.4.1.  Introduction The following instructions allow you to select the correct bit format (number of data bits, stop bits, parity bit status) and bit rate (baud rate: 110, 4800, 9600 etc.) that are required by the application using each I/O port for correct data transfer.   Figure 4-31  Accessing Submenu for Selection     of Bit Formats and Rates (1)  Highlight option “3:SET BIT FORMAT & RATE” on the SET OUTPUT PORTS submenu, and then press .    Another submenu (SET BIT FORMAT & RATE) will then be turned on as shown at right to specify the port for which you wish to select those para– meters.  (2) Using /, select the desired port.   The procedure given below assumes that the SET BIT FORMAT & RATE submenu is currently displayed.   4.12.4.2.  Selecting Parameters for RS–232C Port  The parameters for the RS–232C port are initially set as follows:    Figure 4-32    Checking Current Parameters for RS–232C ・  Data Bits:  8 bits ・  Stop Bits:  1 bit ・ Parity:  None ・  Bit Rate:  110 baud  The current parameter values can be checked by selecting “1:RS–232C” as shown at right.  NOTES:  (1)   If an optional PR–900 printer is plugged into the RS–232C port, be sure to select the following parameters before it can be used to print messages correctly:   DATA BITS = 8,    STOP BITS = 1,    PARITY = NONE,    BIT RATE = 0.11 (110 baud) (2)  If you wish to connect a serial printer other than the  PR–900 to the  RS–232C port, be sure to turn off its hardware flow control and set it to “X–ON/X–OFF,” if available, or an erratic printout can result. (continued on next page) SYSTEM MENU 1: MAKE DISPLAY SETTINGS 2:   SELECT 2ND RECEIVER FREQUENCIES 3:   TURN ON/OFF KEYPRESS BEEP 4:   MAKE SEL / REJ SETTINGS 5:   SEARCH FOR STORED MESSAGES 6.    SELECT OUTPUT MESSAGES 7.  SET OUTPUT PORTS 8.  START SELF–DIAGNOSTIC TESTS 9:  TURN ON/ OFF MESSAGE ALARM 0.    RESET TO FACTORY DEFAULTS 7: SET OUTPUT PORTS 1: SET PORTS ON/OFF 2: SELECT PROTOCOLS 3: SET BIT FORMAT & RATE  3: SET BIT FORMAT & RATE 1: RS–232C   2: RS–422 3: I/O DATA 3: SET BIT FORMAT & RATE1: RS–232C   2: RS–422 3: I/O DATA 1: RS–232C1: DATA BITSI 7  I8I 2: STOP BITS  I1I 2 3: PARITY  ODD  INONEI 4: BIT RATE  i0.11 4.8  9.6 19.2 38.4 0.11=110 baud
AE–1800 Instruction Manual Customizing Operation via Menu System 4.12.4.2.  Selecting Parameters for RS–232C Port (continued – 2 / 2)  If your RS–232C application requires a different set of parameters, select the appropriate values by following the steps given below:  (1)  Press /to highlight the desired parameter.   For example, to change the parity bit status to non–parity, highlight “ 3:PARITY.”  (2) Press /to highlight the desired value, and then press .    For example, highlight “NONE” and press  .  Figure 4-33    Changing Parity Bit Status Parameter – Example             (3) Press   to return to the previous submenu or   to return to the first receiver text page.   4.12.4.3.  Selecting Parameters for RS–422 Port  The parameters for the RS–422 port are initially set as follows:    Figure 4-34    Checking Current Parameters for RS–422  ・  Data Bits:  8 bits ・  Stop Bits:  1 bit ・ Parity:  Odd parity ・  Bit Rate:  4800 baud  The current parameter values can be checked by selecting “2:RS–422” as shown at right.   Each parameter can be changed in the same manner as in the example given above (paragraph 4.12.4.2). Be sure to press  after selecting the desired value.  (continued on next page) 1: RS–232C 1: DATA BITS  7  I8I 2: STOP BITS  I1I 2 3: PARITYI ODD INONEI 4: BIT RATE  i0.11 4.8  9.6  19.2  38.4 (1) Highlight this with /. (2) Highlight this with /, and press . 3: SET BIT FORMAT & RATE1: RS–232C   2: RS–422   3: I/O DATA 2: RS–4221: DATA BITSI 7  I8I 2: STOP BITS  I1I 2 3: PARITY  iODD NONE 4: BIT RATE  0.11  4.8 9.6 19.2 38.4
AE–1800 Instruction Manual Customizing Operation via Menu System 4.12.4.4.  Selecting Parameters for I/O DATA Port  The parameters for the I/O DATA port are initially set as follows:  ・  Data Bits:  8 bits ・  Stop Bits:  1 bit ・ Parity:  Odd parity ・  Bit Rate:  4800 baud  NOTES: (1)  The message outputs available from the I/O DATA port are the same as those from the printer port (RS–232C). (2)  If you wish to connect a serial printer other than the  PR–900 to the  I/O DATA port, be sure to turn off its hardware flow control and set it to “X–ON/X–OFF,” if available, or an erratic printout can result.  The current parameter values can be checked by selecting “3:I/O DATA” on the SET BIT FORMAT & RATE submenu, as shown below.  Figure 4-35    Checking Current Parameters for I/O DATA Port                           Each parameter value can be changed using / and /in the same man– ner as in the example given in paragraph 4.12.4.2.  Be sure to press  after selecting the desired value.  SYSTEM MENU  1: MAKE DISPLAY SETTINGS 2:   SELECT 2ND RECEIVER FREQUENCIES3:   TURN ON/OFF KEYPRESS BEEP 4:   MAKE SEL / REJ SETTINGS 5:   SEARCH FOR STORED MESSAGES 6.    SELECT OUTPUT MESSAGES 7.  SET OUTPUT PORTS 8.  START SELF–DIAGNOSTIC TESTS 9:  TURN ON/ OFF MESSAGE ALARM 0.    RESET TO FACTORY DEFAULTS 7: SET OUTPUT PORTS 1: SET PORTS ON/OFF 2: SELECT PROTOCOLS 3: SET BIT FORMAT & RATE 3: SET BIT FORMAT & RATE 1: RS–232C 2: RS–422 3: I/O DATA   3: I/O DATA1: DATA BITSI 7  I8I 2: STOP BITS  i1i 2 3: PARITY  iODDi NONE 4: BIT RATE  0.11  I4.8I 9.6 19.2 38.4
AE–1800 Instruction Manual Customizing Operation via Menu System 4.13. Performing Self–Diagnostic Tests    Figure 4-36    Starting Self–Diagnostic Test 4.13.1. Introduction  Selecting option “ 8: START SELF–DIAGNOSTIC TESTS” opens a test report window  as shown at right and at the same time initiates auto– matically the built–in function of self–diagnostic tests to check the integrity of important hardware com– ponents of the equipment.  NOTE: The test functions cannot be executed during live message reception.   The self–diagnostic tests should be conducted once a year as a part of regular maintenance.  The following components will be checked:  ・  First Receiver (518 kHz) ・  Second Receiver (490 kHz or 4209.5 kHz, currently selected) ・  ROM (flash memory embedded in CPU chip, for software storage) ・ RAM (DRAM  embedded in CPU chip, for software execution) and (SRAM mounted on CPU PCB, capacitor–backed, for message/ID storage) ・ Alarm (audible) ・  Keypad dimmer lamps   4.13.2.  Activating Self–Diagnostic Test Function  (1)  Allow the equipment to warm up for at least 30 minutes before activating the test function if the unit was switched off before the test.  (2) Press  to open the system menu, highlight “8: START SELF–DIAGNOSTIC TESTS” and press  . A test report window will show up as in the example above, and the tests will start automatically. To cancel the execution, press . If reception of a NAVTEX message is already in progress, the function cannot be activated, and the following caution will be turned on, blinking in reverse video. iWAIT FOR MESSAGE RECEPTION TO END!i   Press to turn it off, returning to the text screen. (continued on next page) SYSTEM MENU 1: MAKE DISPLAY SETTINGS 2:   SELECT 2ND RECEIVER FREQUENCIES 3:   TURN ON/OFF KEYPRESS BEEP 4:   MAKE SEL / REJ SETTINGS 5:   SEARCH FOR STORED MESSAGES 6.    SELECT OUTPUT MESSAGES 7.  SET OUTPUT PORTS 8.  START SELF–DIAGNOSTIC TESTS 9:  TURN ON/ OFF MESSAGE ALARM 0.    RESET TO FACTORY DEFAULTS 8: START SELF–DIAGNOSTIC TESTS SELF–DIAGNOSTIC TEST REPORT 1: TESTING RECEIVERS    1ST RCVRI(518KHZ)I STARTING   2ND RCVR (490KHZ)  2: TESTING ROM 3: TESTING RAM 4: TESTING ALARM 5: TESTING KEYPAD LAMPS  SOFTWARE VER. 1.0   REV_1.1A1 DATE OCT 06, 2007
AE–1800 Instruction Manual Customizing Operation via Menu System 4.13.3.  Checking Test Results  Figure 4-37    Results of Self–Diagnostic Test – Example  The function will be terminated automatically just after completion of the keypad dimmer lamp test (TESTING KEYPAD LAMPS on the test report). The test report window will remain to allow the user to check the tests results. The figure at right shows an example of the test report showing the results of the self– diagnostic tests.        The result of each check will be available in one of the following indications:  ・ OK:    Tested hardware is functioning normally (for test items 1, 2 and 3). ・ FAILED:    Malfunction of tested hardware is detected (for test items 1, 2 and 3).     If this indication shows up, see section 5 (User–Level Trouble– shooting) for actions to be taken, or contact your dealer for assistance.   NOTE: If the receiver test result is “FAILED,” check to be sure that the unit has been turned on for at least 30 minutes before starting the test. This warm–up period is necessary for the internal test oscillators to become stable. The “FAILED” indication should not be immediately interpreted as a sign of receiver malfunction if the unit was tested shortly after power–up. ・ COMPLETE: Test is completed (for test items 4 and 5). The user should check whether the tested hardware component functioned correctly.  (1)  Result of Audible Alarm Test   Execution of the test “4:TESTING ALARM” checks the buzzer function of the audible alarm circuit. On successful completion of the test, the buzzer should sound three slow beeps. If no sound is heard, see section 5 (User–Level Troubleshooting) for actions to be taken, or contact your dealer for assistance.  (2)  Result of Keypad Backlighting Lamp Test   Execution of the test “5:TESTING KEYPAD LAMPS” checks the light–emitting diodes (LEDs) that illuminate the keys and their control circuit. All keys should be lit blinking at the maximum level during the test. If no key is lit or if some of the keys remain extinguished, see section 5 (User–Level Troubleshooting) for actions to be taken, or contact your dealer for assistance.    This test result should be checked in a dark environment for ease of checking. 8: START SELF–DIAGNOSTIC TESTS SELF–DIAGNOSTIC TEST REPORT 1: TESTING RECEIVERS  1ST RCVR((518KHZ)((518KH OK   0123456789 ( ).,=?  ABCDEFGHIJKLMNOPQRSTUVWXYZ  2ND RCVR (490KHZ)  OK   0123456789 ( ).,=?  ABCDEFGHIJKLMNOPQRSTUVWXYZ 2:  TESTING ROM  OK 3: TESTING RAM  OK 4: TESTING ALARM  COMPLETE 5: TESTING KEYPAD LAMPS   COMPLETE  SOFTWARE VER. 1.0   REV_1.1A1 DATE OCT 06, 2007
AE–1800 Instruction Manual Customizing Operation via Menu System 4.14. Turning on/off Message Alarms  The alarm function for types A (navigational warning), B (meteorological warning) and L (additional navigational warning) messages is initially disabled unless it was already set otherwise by your dealer. If you wish to enable some or all of the message alarms, follow the steps given below. The alarm for type–D messages (SAR, piracy and armed robbery information) cannot be disabled due to the relevant IMO resolutions.  (1) Press , opening the system menu.  (2) Using /, highlight “9: TURN ON/OFF MESSAGE ALARMS” and then press . The current alarm ON/OFF status will then be displayed on a submenu as in the example below.   Figure 4-38    Initial Alarm Status                    (3)  Highlight the desired message type with /, and then highlight status indication “ON” by pressing, as in the example below.  Figure 4-39    Enabling Alarm for Type–B Messages            Be sure to press  after selecting the desired setting.  (4) Press   to return to the previous submenu or   to return to the first receiver text page.  SYSTEM MENU 1: MAKE DISPLAY SETTINGS 2:   SELECT 2ND RECEIVER FREQUENCIES3:   TURN ON/OFF KEYPRESS BEEP 4:   MAKE SEL / REJ SETTINGS 5:   SEARCH FOR STORED MESSAGES 6.    SELECT OUTPUT MESSAGES 7.  SET OUTPUT PORTS 8.  START SELF–DIAGNOSTIC TESTS 9:  TURN ON/OFF MESSAGE ALARMS 0.    RESET TO FACTORY DEFAULTS 9: TURN ON/OFF MESSAGE ALARMS1: MESSAGE A:I ON iOFF   2: MESSAGE B: ON iOFF   3: MESSAGE D: ON 4: MESSAGE L: ON iOFF Enabled/Disabled Status 9: TURN ON/OFF MESSAGE ALARMS1: MESSAGE A: ON iOFFi 2: MESSAGE B:i iONi OFF 3: MESSAGE D: ON 4: MESSAGE L: ON iOFFiPress to highlight ON.
AE–1800 Instruction Manual Customizing Operation via Menu System 4.15. Resetting the System  If, for any reason, you wish to reset the system to return all current operational settings to the initial factory settings, follow the steps given below. Initialization of the settings does not affect the message storage; all stored messages will be retained.     Figure 4-40    Resetting the System – Step 1  (1) Press , opening the system menu.  (2) By pressing /, highlight “0:RESET TO FACTORY DEFAULTS” and then press . This opens a submenu, asking you to confirm whether to reset the system, as illustrated at right.        (3) Press   to highlight “2: YES (EXECUTE)” as shown below.  Figure 4-41    Resetting the System – Step 2           (4) Press . This will reset the system and initialize all the settings you have made, and then return you automatically to the first receiver text page.   Attention to NAVTEX Printer Users  If you are using an optional PR–900 printer or other serial printer plugged into the RS–232C connector to print NAVTEX messages on–line, be sure to set the menu option RECEIVING MSG on the SELECT OUTPUT MESSAGES submenu to “ ON” again via the instructions in paragraph 4.11.2 on completion of the resetting. No printout will result if the above menu option is set to “OFF,” which is the default setting.    0: RESET TO FACTORY DEFAULTS ARE YOU SURE ? 1: NO(CANCEL)  2: YES(EXECUTE)  Press  after highlightingthis option with . SYSTEM MENU 1: MAKE DISPLAY SETTINGS 2:   SELECT 2ND RECEIVER FREQUENCIES 3:   TURN ON/OFF KEYPRESS BEEP 4:   MAKE SEL / REJ SETTINGS 5:   SEARCH FOR STORED MESSAGES 6.    SELECT OUTPUT MESSAGES 7.  SET OUTPUT PORTS 8.  START SELF–DIAGNOSTIC TESTS 9:  TURN ON/ OFF MESSAGE ALARMS 0.    RESET TO FACTORY DEFAULTS   0: RESET TO FACTORY DEFAULTS ARE YOU SURE ? 1: NO(CANCEL)  2: YES(EXECUTE)
AE–1800 Instruction Manual User-Level Troubleshooting 5. User–Level Troubleshooting  A list of common troubles the user may experience while operating the equipment is given below along with recommended remedies for such troubles. If a problem persists, contact your dealer for assistance, giving as much information as possible about the symptom, self–diagnostic tests results (paragraph 4.13), power supply voltage, antenna configuration, operating frequency, control and menu settings used, serial number of, and *1software version (VER.) and revision (REV.) numbers of, your equipment. *1 The software version and revision numbers are displayed in the opening message window that appears briefly at power–up. Those data will also be displayed when the self–diagnostic tests are conducted (paragraph 4.13). < WARNING > NO USER–SERVICEABLE PARTS ARE INSIDE THE CABINET. QUALIFIED PERSONNEL SHOULD MAKE IT SURE TO SWITCH THE EQUIPMENT OFF AND UNPLUG THE POWER CORD BEFORE OPENING THE CABINET FOR INSPECTION OR REPAIRS.  5.1. Power–Up Problems  The following description of the symptoms assumes that the equipment was working correctly for some time after its initial installation.  Symptom  Suggested Solution             The equipment cannot be turned on.    1.  Check if the power cord is plugged into the three–pin rear panel connector (POWER).  2.  Check if the power cord is connected to the ship’s DC power source with the correct polarity.  NOTE: Reversing the power cord polarity causes the fuse (3A) to blow.  3.  Check the voltage of the power source.  NOTE: The nominal power supply voltage is 24 VDC. The equipment works safely over the voltage range from 11 to 36 VDC.  4.  Check the fuse inside the rear panel fuse holder. If it is found blown, replace it with a correct replacement (3A, 5.2X20mm).  5. If it blows again, unplug the active antenna cable from the rear panel connector, and then check if the problem persists. If it does not, suspect that the antenna amplifier or the cable developed a short. Replace the antenna and cable.  6.  If replacing the antenna still does not correct the problem, suspect that the Main PCB has become defective. Ask your dealer/qualified engineer to check each board by replacement. 7. If all attempts above fail, ask your dealer/qualified service engineer to replace the CPU PCB.
AE–1800 Instruction Manual User-Level Troubleshooting 5.2. No Message Reception  The following description of the symptoms assumes that NAVTEX messages were properly received for some time after initial installation.  Symptom  Suggested Solution  No messages can be displayed except for warning messages.  No NAVTEX messages can be received, except for navigational warnings, weather warnings, SAR/piracy/armed robbery warnings or other warnings.  1.  Check the current message rejection (RJ) settings by pressing .  2. Select  all  desired message types for display and memory storage, via the steps given in paragraph 4.9.  No messages can be displayed from desired transmitters.  No NAVTEX messages can be displayed from some transmitters at any time even if you are within the coverage areas.   1.   Check the current station rejection (RJ) settings by pressing .  2.  Select the IDs of all desired transmitters for display and storage in memory, via the steps given in paragraph 4.8.           No messages can be displayed despite correct selection settings and appearance of “RCVNG MSG.”  No NAVTEX messages can be displayed regardless of the correct display and storage selection (SL) settings for all desired messages or transmitters, or regardless of the “RCVNG MSG” status indication during reception.    1.  The same message was received before or the currently receiving message has a character error rate (CER) > 33%.  See subparagraphs ④,  ⑪ and ⑫ in paragraph 1.1 for details.  2.  Run the self–diagnostic tests via the steps given in paragraph 4.13, and check if the receiver test result is “OK.”    If the test result indication shows “FAILED,” suspect that the receiver PCB has become defective. Ask your dealer or qualified engineer to check all wiring harnesses to/ from the PCB and to replace the PCB if necessary. The chance of any receiver being out of tune is very small in normal usage. 3.  Check if you are located within the service area covered by the ground wave of the desired station. The ground wave coverage normally extends to 200 – 400 nautical miles from each station during daytime hours. 4. Check the broadcast schedule of the desired station. Each station usually transmits messages for 5 to 10 minutes at intervals of 4 hours. 5. Check the active antenna unit and/or cabling by replacement.  (continued on next page)
AE–1800 Instruction Manual User-Level Troubleshooting 5.2. No Message Reception – 2/3  Symptom  Suggested Solution    No messages can be received in the daytime.  No NAVTEX messages can be received on 518 kHz or 490 kHz during daytime hours despite appropriate station and message type selection (SL) settings. 1.  Check if you are located within the service area covered by the ground wave of the desired station. The area is normally 200 to 400 nautical miles from each station during daytime hours. At night, MF NAVTEX signals (518 /490 kHz) can travel  distances in excess of 1000 nautical miles depending on the season and ionospheric conditions. Nighttime signal propagation changes greatly with the season. 2. Check the broadcast schedule of the desired station. Each station usually transmits for 5 to 10 minutes at intervals of 4 hours. Currently transmitting stations may be outside the coverage area.             No messages can be received even during a broadcasting time and while in the service area.  No NAVTEX messages can be received regardless of being in the service area of a currently transmitting station and of appropriate message type and station selection settings.  1.  Check if the antenna cable is correctly plugged into the rear panel BNC connector receptacle. 2. Check if the BNC plug is properly installed onto the cable.   Check also the coupling connectors, if used for cable extension. 3.  Check by replacing the active antenna.   The antenna preamplifier unit may have been destroyed by static discharges.  If a correct replacement is not available, run at least 5 meters of insulated wire from the BNC connector’s center conductor as a temporary long wire antenna, and place it as high as possible from the ground level. < WARNING >  DO NOT SHORT THE OTHER END OF THE WIRE ANTENNA TO GROUND, OR DAMAGE TO THE UNIT’S POWER SUPPLY WILL RESULT. 4.  If replacing the antenna still does not solve the problem, check the voltage at the center conductor of the antenna connector. It should be 8V+ at 490 and 518 kHz, and 12V+ at 4209.5 kHz.       If no voltage is present or if it is extremely low, ask your dealer/qualified engineer to check the wiring to/from the Main PCB first and to replace the PCB, if necessary. 5.  If all attempts above fail to correct the problem, ask your dealer/qualified engineer to check the related connections to/from the Main PCB first and to replace the PCB, if necessary.  (continued on next page)
AE–1800 Instruction Manual User-Level Troubleshooting 5.2. No Message Reception – 3/3  Symptom  Suggested Solution    No messages can be received at any time on the first or the second receiver with a good replacement antenna plugged in, but the results of the self–diagnostic tests are “OK” for both receivers.  No NAVTEX messages can be received at any time and anywhere on either the first or the second receiver after the antenna is replaced with one known to be good. The self–diagnostic tests (paragraph 4.13) show that both receivers are working properly. The symptom is an indication that the antenna circuit has become defective. 1.  Replace it with one known to be good. 2.  If a correct replacement antenna is not available, run approx. 5 meters of insulated wire from the center conductor of the appropriate connector as a temporary long wire antenna, and place it as high as possible from the ground level. < WARNING>  DO NOT SHORT THE OTHER END OF THE WIRE ANTENNA TO GROUND, OR DAMAGE TO THE UNIT’S POWER SUPPLY WILL RESULT. 3. If replacing the antenna still does not solve the problem, ask your dealer/ qualified engineer to check the antenna coupler/selector circuit inside the rear apron for faulty or broken connections.   No messages can be received at any time on the first or the second receiver with a good replacement antenna plugged in, and the results of the *self–diagnostic tests are “FAILED” for both receivers. * 30 minute warm–up period required before test. 1. The symptom suggests that either receiver has got out of alignment. Ask your dealer/qualified engineer to check the connections to/from the receiver PCB and/ or replace the PCB. 2:  The Main PCB has also become defective and/or some of the internal connections to the PCB have become faulty or broken. Ask your dealer/ qualified engineer to check the related wiring harnesses to/ from the CPU PCB first and to replace the PCB, if necessary.  5.3. Message Storage Problems  Symptom  Suggested Solution  Some stored messages disappear from memory after some time. Messages will be erased from memory after 60 hours, unless they are protected from automatic erasure. Put the “PROTECTED” tag to each desired message via the steps in paragraph 3.8.  None of the received messages is stored after power–off. The symptom indicates that the memory backup circuit on the CPU PCB is failing. Ask your dealer or qualified engineer to replace the CPU PCB.  All messages disappear from memory after continued power–off for some time. The memory retains stored messages for at least 10 days after power–off. Print out desired messages using an optional printer before switching the unit off for extended periods of time continuously.
AE–1800 Instruction Manual User-Level Troubleshooting 5.4. Poor Reception  The following description of the symptoms assumes that NAVTEX messages were properly received for some time after initial installation time, and all message types and transmitter IDs you wish to receive are selected (via the steps in paragraphs 4.8 & 4.9).  Symptom  Suggested Solution                  Messages can be received in the daytime, but with many error characters (*) at all times.  NAVTEX messages can be received but with many error characters (asterisks) and often cannot be stored.   1.  Check if you are located within the service area covered by the ground wave of the desired station. The area is normally 200 to 400 nautical miles from each station during daytime hours. At night, NAVTEX signals can travel distances in excess of 1000 nautical miles depending on the season and ionospheric conditions. 2. Run the self–diagnostic tests as per paragraph 4.13, and check the receiver test results. If the result for the receiver in question is “FAILED,” ask your dealer/qualified service engineer to check the related wiring harnesses to/from the receiver PCB or replace the PCB. 3.  Check if you have recently installed an electronic device near the receiver cabinet receiver or near the antenna. Turn off or relocate such equipment away from the NAVTEX receiver, and see if any improvement can be obtained. 4.  Unplug the antenna cable from the rear panel BNC connector, and check the voltage at the center conductor. It should be 8V+ on the ACTIVE ANT and 518 kHz connectors, and 12V+ on the 490/4209.5 kHz connector.    If no voltage is present or the voltage is extremely low, ask your dealer/qualified service engineer to check the related connections to/from the Main PCB first and to  replace the PCB, if necessary. 5. Suspect that the preamplifier in the active antenna unit is failing or water intruded into the cable via the junction. Check by replacing the amplifier unit and/or the cable.  If a correct replacement antenna is not available, run at least 5 meters of insulated wire from the center conductor of the appropriate connector as a temporary long wire antenna, and place it as high as possible from the ground level.  < WARNING>  DO NOT SHORT THE OTHER END OF THE WIRE ANTENNA TO GROUND, OR DAMAGE TO THE UNIT’S POWER SUPPLY WILL RESULT.
AE–1800 Instruction Manual User-Level Troubleshooting 5.5. Blank Message Screen  The following description of the symptom assumes that your NAVTEX receiver was properly working for some time after initial installation time.  Symptom  Suggested Solution      The NAVTEX receiver can be turned on but the message screen remains blank. 1.  Check to be sure that the power source voltage is within the 11–36V range. 2. Repeatedly press  to check if the normal brightness returns. 3.  Suspect that the LCD module or Main PCB has become defective. Ask your dealer/qualified service engineer to check the related connections to/from the module and the Main PCB, and replace the module and/ or the PCB. 4.  Suspect that the Main PCB has become defective. Ask your dealer/qualified engineer first to check the related connections to/from the PCB, and to replace the PCB, if necessary.   5.6. Uncontrollable Screen Brightness  The following description of the symptom assumes that your NAVTEX receiver was properly working for some time after initial installation time.  Symptom  Suggested Solution  The NAVTEX receiver can be turned on but the message screen brightness cannot be controlled.  The brightness level does not change by pressing  . 1.  Check to be sure that the power source voltage is within the 11–36V range.  2.  Suspect that the Main PCB has become defective. Ask your dealer/qualified engineer to check the wiring harnesses to/from the PCB first and to replace the PCB, if necessary.   5.7.  No Beep from Keypress  The following description of the symptom assumes that your NAVTEX receiver was properly working for some time after initial installation time.  Symptom  Suggested Solution   No keypress beep is heard.  1.  Check if the keypress beep function is disabled. Refer to paragraph 4.7 for instructions. 2. Ask your dealer/qualified engineer to check the related wiring to/from the keypress buzzer.
AE–1800 Instruction Manual User-Level Troubleshooting 5.8.  No Response from Keypress  The following description of the symptom assumes that your NAVTEX receiver was properly working for some time after initial installation time.  Symptom  Suggested Solution       The NAVTEX receiver can be turned on but does not respond to any keypress.  1.  Check to be sure that the power source voltage is within the 11–36V range.  2.  Reset the system, returning all settings to the factory’s initial settings via the procedure given in paragraph 4.15.  3.  Suspect that the Main PCB or the Keypad PCB has become defective. Run the self–diagnostic tests (as per paragraph 4.13), and check the result of the RAM and ROM tests. If the either test result is “FAILED,” ask your dealer/qualified service engineer to check the related connections to/from these PCBs first, and to replace either or both PCBs, if necessary.   5.9. No Message Alarm Indication  The following description of the symptom assumes that your NAVTEX receiver was properly working for some time after initial installation time.  Symptom  Suggested Solution No audible or visual alarm indication is available when navigational warnings (type–A messages) or meteorological warnings (type–B messages) are received.  The alarm function for type–A and type–B messages are initially disabled. To turn it on, refer to paragraph 4.14 for instructions.       No audible alarm indication is available when a Search & Rescue (SAR) or distress message is received. 1.  Run the self–diagnostic tests as per the steps given in paragraph 4.13, and check the result of the alarm test.  If no beep is heard on completion of the tests, suspect that a fault has developed in the wiring harness to/from the message buzzer or the buzzer has become defective. Ask your dealer/qualified engineer to check the related wiring harnesses and the buzzer.  2.  Suspect that the Main PCB has become faulty. Run the self–diagnostic tests and check the result of the RAM and ROM tests. If the result is “FAILED,” ask your dealer/qualified engineer to check the PCB by replacing.
AE–1800 Instruction Manual User-Level Troubleshooting 5.10. No Message Alarm Output  The following description of the symptom assumes that your NAVTEX receiver was properly working for some time after initial installation time.  Symptom  Suggested Solution        No alarm output is available from the rear panel ALARM connector.  1.  The alarm function for type–A and type–B messages are initially disabled. To turn it on, refer to paragraph 4.14. 2.   Run the self–diagnostic tests via the steps in paragraph 4.13, and check the results of the RAM and ROM tests. If the test result is “FAILED,” suspect that the Main PCB has become faulty. Ask your dealer/qualified engineer to check the PCB by replacing. 3. Suspect that some of the connections to/from the connector have loosened or the Main PCB has become faulty. Ask your dealer/qualified engineer to check the related wiring harness terminations.   5.11. No External Outputs  The following description of the symptom assumes that your NAVTEX receiver was properly working for some time after initial installation time.  Symptom  Suggested Solution        No messages can be output from the memory to the printer or I/O DATA port or to the INS port despite correct connections to the appropriate rear panel connector.  1.  Check to be sure that all ports are enabled (set to ON) and that the communications protocol of your application matches that of the port (rear panel connector) in use. See paragraph 4.12.  2. Press and then check that the memory storage (ME), printer port output (PR) and INS port output (IN) settings are set to the “SL” status. See paragraphs 4.8 and 4.9 for details. 3. Suspect that some of the connections to/from the connectors have become loosened or broken. Ask your dealer/ qualified engineer to check for faulty wiring harness terminations. 4.  Suspect that the Main PCB has become defective. Ask your dealer/qualified engineer to check the PCB first and replace it if necessary.
AE–1800 Instruction Manual User-Level Troubleshooting 5.12. External Control Problem  The following description of the symptom assumes that your NAVTEX receiver was properly working for some time after initial installation time.   Symptom  Suggested Solution            Alarm acknowledgement cannot be controlled remotely from IBS/INS terminals despite correct connections to the INS port (RS–422 connector).  1.  Check to be sure that the RS–422 (INS) port is enabled (set to ON). See paragraphs 4.12.1 through 4.12.4 for details.  2.  Check to be sure that the communications protocol of your application matches that of the RS–422 (INS) port. See paragraph 4.12.2.2 for details. 3.  Check the bit format and baud rate of your application match those of the RS– 422 port parameters. See paragraph 4.12.4 for details. 4. Suspect that some of the internal connections to/ from the connectors have become loosened or broken. Ask your dealer/qualified engineer to check for faulty wiring harness terminations.  5. Run the self–diagnostic tests as per paragraph 4.13, and check the results of the RAM and ROM tests.   If the indication of either result is “FAILED,” suspect that the Main PCB has become defective. Ask your dealer/ qualified engineer to check the PCB and related wiring harnesses first and to replace it if necessary.
AE–1800 Instruction Manual User-Level Maintenance 6.  User–Level Maintenance Instructions To ensure long–term trouble–free operation, the user should regularly follow the maintenance instructions described in this section.  6.1.  Maintenance on the Equipment Cabinet Keep the equipment, away from sea splashes, direct sunlight and other heat–generating sources, and make sure that air around the cabinet is circulating freely. If the equipment is not going to be used for extended periods of time, dismount the cabinet  from the vessel and place them in dry storage. Be sure to switch the equipment off before removing electrical connections from the rear panel.  < WARNINGS > 1.  BE SURE TO TURN IF OFF AND UNPLUG THE POWER CABLE BEFORE OPENING THE CABINET FOR INSPECTION. 2.  CHEMICAL SOLVENTS, SUCH AS PAINT THINNERS AND BENZENES, MUST NOT BE USED TO CLEAN THE CABINET OR SCREEN FILTER, OR PERMANENT DAMAGE TO THOSE PARTS WILL RESULT. 3.  ALL MESSAGES STORED IN MEMORY, INCLUDING PROTECTED ONES, WILL BE ERASED IF THE UNIT IS TO BE TURNED OFF CONTINUOUSLY IN EXCESS OF 10 DAYS. IMPORTANT MESSAGES SHOULD BE PRINTED OUT OR SAVED INTO  APPROPRIATE STORAGE MEDIA VIA A PC CONNECTED TO THE RS–422 PORT.  To clean the cabinet surface, a neutral type household detergent intended for office equipment is recommended. Cleaning the acrylic filter on the LCD screen should be a maintenance routine to avoid using a high brightness level. To clean the screen filter, use a piece of slightly wet cloth. If stains persist, the cloth may be moistened with a neutral type household detergent.  To prolong LCD Screen’s Service Life To increase the service life of the LCD screen (life of the white LED lamps for backlighting), it is recommended that the screen sleep mode be activated as per the instructions in paragraph 4.5.  6.2.  Maintenance on Electrical Connections The high humidity marine environment can cause electrical contacts in the rear panel connectors to corrode over time. Vibrations and shocks normally encountered on the vessel in motion can cause the electrical contacts to become loosened. Corroded or loose contacts will become responsible for erratic, intermittent operation or performance degradation. To avoid such possible problems, conduct the following maintenance operations at least once a year: ●   Unplug all the cables from the rear panel, and check to be sure that contact surfaces, including the pins in the rear–panel mounted receptacles are free from corrosion. ●  Check the connections at the ship’s DC power source for freedom from any sort of corrosion. ● Correct any problem using a high quality contact–cleaning agent (contact rejuvenator).  < WARNINGS > 1.  BE SURE TO TURN THE EQUIPMENT OFF BEFORE REMOVING / INSTALLING THE CONNECTIONS FROM / TO THE REAR PANEL CONNECTORS. 2.  SANDPAPER WILL DAMAGE THE CONTACT SURFACE AND MUST NOT BE USED.
AE–1800 Instruction Manual User-Level Maintenance 6.3.  Maintenance on The Active Antenna Unit  The ANT–2000M active antenna or an optional active antenna unit (e.g.  ANT–900, all consisting of a 1.2m fiberglass whip, a preamplifier housing and coaxial cabling), requires maintenance at least once every six months:  1.  Whip Section  ・ Clean the surface with a piece of soft cloth moistened with neutral household detergent, while checking for any sign of damage.   ・ Check to be sure that the whip is tightly screwed into the socket on the preamplifier case, and that the set screw (hex socket head type) is tightened.   ・  Check to be sure that the knurled metallic base is free from damage or corrosion.   Corrosion may be removed with a piece of wood, and then coated with water– proofing paint. A metallic tool can damage the surface and should not be used  2. Preamplifier Housing  ・ Clean the surface with a piece of soft cloth moistened with neutral household detergent, while checking for any sign of damage.   ・  Check to be sure that the housing is securely screwed onto the pole (if installed on a marine mount) or the mounting hardware is properly secured to the mast (if user–  or dockyard–supplied hardware is used). Do not open the housing; no user–serviceable parts are inside.  3. Cabling   ・ Clean the exposed section with a soft cloth moistened with neutral household detergent, while checking to be sure that the surface is free from any sign of damage.   ・  If the installation uses a double–ended female coaxial coupler for cable extension, check to be sure that the jointed section is properly protected with self–bonding taping and there is no sign of damage.  < WARNING >   THE CENTER CONDUCTOR OF THE COAXIAL CABLE IS AT +8/+12VDC WHEN THE EQUIPMENT IS SWITCHED ON. DO NOT SHORT THE CENTER CONDUCTOR TO GROUND, OR DAMAGE TO THE INTERNAL POWER SUPPLY CIRCUIT CAN RESULT.   6.4. Self–Diagnostic Tests  Once every 12 months, conduct the self–diagnostic tests as per the procedure described in paragraph 4.13, and consult your dealer/qualified service engineer for advice if the result indication of any tested item shows “FAILED.” repeatedly.
AE–1800 Instruction Manual User-Level Maintenance 6.5. Recommended Spare Parts  A list of the spare parts recommended for the maintenance and servicing for three to five years is given below. Replacing parts, except for the active antenna unit, should be done by your dealer or a qualified service engineer. The user should not open the receiver cabinet for inspection or replacing suspected parts. The part number of each product may change depending on its production lot or its availability. If ordered parts are not available, equivalent substitutes will be supplied.  Table 6-1    Recommended Spare Parts                                 Table 6-2    Other Parts Available As Replacements          Part Name  Part Number Quantity  Fuse 3A/5.2X20mm 10 Plugs:   Coaxial Cable Plug (Antenna Plug)  BNC–58/U  2   Power Cable Plug  14–P3F  1  *1I/O DATA Plug  CP111–8P  1  *2RS–422/232C Plug  HDEB–9S  1  *3Coaxial Cable Plug (Extension)  PL–259  1  Active Antenna Unit:  ANT–2000M  Preamplifier Unit  ANT–2KM–BASE    2     Whip Element (1.2m)  ANT–2K–RODE    1   Printed Circuit Boards (PCBs):  Receiver PCB  S602–RCV–X*4  1  Main PCB  M613–MAIN–X*4  1  Keypad PCB  M401–KEY–X*4  1    *1 Not needed unless the I /O DATA port is used in your applications. *2 Not needed unless RS–232C /RS–422 port is used in your applications. *3 Dealer–supplied. Not needed unless the cable is extended with a PL–258 connector. *4 The suffix (last digit) will change depending on production lot. Part Name  Part Number   TFT LCD Module (LCD display panel)  LQ057AC111
AE–1800 Instruction Manual Installation 7. Installation  7.1.  Receiver Cabinet Installation  7.1.1. General Precautions The receiver cabinet is constructed to withstand the humid and corrosive marine environment, but is designed to be installed or operated inside the wheelhouse or chartroom. The cabinet is a “protected” category product under the IEC 60945–2002 standard, and is not waterproof. Serious damage will result to the electronics inside the cabinet when it is exposed to salt water spray or splash.  Additional Requirements: (1)  For long term trouble–free service, the proposed site for installation should be:  ・ dry, well–ventilated and free as much as possible from shocks and engine vibrations.  ・ away as much as possible from high temperature outlets (such as exhaust fans and heaters), and as much as possible from areas where the unit is likely to be constantly exposed to direct sunlight.  (2)  To prevent reception of weak NAVTEX signals from being interfered with, the unit should also be located away as much as possible from other onboard electronics, especially those emitting pulsed signals, such as echo sounders and radars.   7.1.2.  Mounting the Receiver Cabinet  The receiver cabinet is primarily designed to be mounted on a tabletop with the mounting bracket supplied and weights approximately 2.3 kg in total. The dimensions necessary for installation are given in Figure 7–1. Provide sufficient clearance behind the cabinet for cabling termination and maintenance checks. Using a total of four appropriate wood screws or bolt/nut combinations through its four mounting holes (9 mm in diameter each), secure the bracket to the selected site. Make sure that the mounting surface is strong enough to support the unit against shocks or vibrations that are likely to be encountered with the ship in motion.  Compass Safe Distances (in energized condition): ・  Receiver Cabinet alone:  0.45m (standard),    0.30m (steering) ・  Cabinet with Bracket:  0.60m (standard), 0.35m (steering)  < WARNINGS > 1.  DO NOT PLACE THE UNIT IN AN UNVENTILATED, SEALED ENCLOSURE, SUCH AS A THEFT–DETERRENT CABINET, OR OVERHEATING AND MALFUNCTION WILL RESULT. 2.  DAMAGE CAUSED BY EXPOSURE TO WATER SPRAY OR TO DIRECT SUNLIGHT WILL NOT BE COVERED BY THE MANUFACTURER’S WARRANTY.  (continued on next page)
AE–1800 Instruction Manual Installation 7.1.2.  Mounting the Display Cabinet (continued – 2/2)  Be sure to attach a serrated plastic washer to the inside of each arm before placing the cabinet in the bracket. This pair of washers is supplied separately in the plastic bag that contains the power cable, fuses, plugs, etc., and prevents the cabinet from leaning forward or backward with the clamping knobs tightened.  After tilting the cabinet to a desired viewing angle, tighten each knob firmly.   Figure 7-1 Installation Dimensions                                           215Dimensions in millimeters Weight (approx.): ・ Cabinet only:   1.7 kg ・ Cabinet + Bracket:  2.3 kg  Compass Safe Distances: ・ Cabinet only:   45 cm (STD), 30 cm (STG) ・ Cabinet + Bracket:   60 cm (STD), 35 cm (STG)
AE–1800 Instruction Manual Installation 7.2. Antenna Installation  The dimensions of the active antenna unit (ANT–2000M) is given in Figure 7–2.. The equipment does not support the use of a wire antenna. The receiver input is low impedance and is not suitable for wire antenna connection.    7.2.1.  Installation Site Requirements  For best results and a prolonged service life, the active antenna unit should be installed: ・  at a site free from continuous heavy shocks and vibrations, ・ away as much as possible from the feedpoint or radiating elements of HF/MF communications antennas, radar scanners and INMARSAT antennas, and ・  away as much as possible from, and above, any metallic obstructions.   < WARNING > LOCATING THE ACTIVE ANTENNA CLOSE TO THE FEED POINT OR RADIATING ELEMENTS OF AN HF/MF TRANSMITTING ANTENNA CAN DESTROY THE PREAMPLIFIER IN THE CYLINDRICAL HOUSING.    7.2.2.  Precautions for Cabling  ・ To minimize the effect of interference from other onboard electronics, the coaxial cable from the antenna unit should not be run close to, and in parallel with, transmit antenna feed lines, radar waveguides, echo sounder transducer cables, control cables, power cables, etc. from such equipment. The same requirements apply to the routing of the long wire antenna.  ・  If the cable is extended with coaxial connectors ( e.g. PL–258/PL–259 pairs), be sure to make the junctions waterproof using self–bonding tape or other appropriate sealant.   < WARNING > THE CENTER CONDUCTOR OF THE COAXIAL CABLE IS AT +8 VDC (OR AT +12V WITH THE SECOND OPERATING AT 4209.5 KHZ) WITH THE EQUIPMENT SWITCHED ON. DO NOT SHORT THE CENTER CONDUCTOR TO GROUND OR DAMAGE TO THE INTERNAL CIRCUITRY CAN RESULT.   < CAUTION > Water intrusion into the coax cable will electrically damage the cable, making it impossible to use it as a feeder any longer. A serious drop in sensitivity will result.   (continued on next page)
AE–1800 Instruction Manual Installation 7.2.2.  Precautions for Cabling (continued –2/2)  Figure 7-2    ANT–2000M Active Antenna Unit Dimensions                                                  Not Supplied The dimensions are in millimeters except forthe socket section at the base of thepreamplifier housing.  The socket is internally threaded so that itcan accept a 1”–14 straight thread standardmarine pole. To prevent possible loosening,apply a suitable locking compound over thethreads before screwing the socket over thepole.  < WARNING > DO NOT USE A WRENCH, PLIERS ORSIMILAR TOOL TO SCREW THE HOUSINGONTO THE POLE, OR DAMAGE TO THESOCKET’S THREADS WILL RESULT.  The preamplifier housing may be secured to asuitable pole of less than 9 centimeters indiameter, using a set of appropriate mountinghardware ( e.g. stainless steel hose clampsand bands). Whip ANT–2K–ROD  Preamplifier Housing ANT–2KM–BASE
AE–1800 Instruction Manual Installation 7.3. Electrical Connections  7.3.1. Introduction All electrical connections to the equipment are to be made via the connector receptacles and terminal installed on the rear panel and the rear apron. The figure below shows the rear view of the equipment. Overall connections are illustrated in Figure 7–4. A summary description of the necessary connections to each component is given in the next paragraphs.  < CAUTIONS > 1.  All cables should be plugged in with the equipment switched off. 2. Power cables specified for use with the F–2000/F–3000 or DEBEG 4620/DEBEG 4630 Navigation Sounders cannot be used as alternative cables.  Figure 7-3  Rear View                                   (continued on next page)  ⑧ ⑥ ④ ⑤  ⑦ ③ ① ②
AE–1800 Instruction Manual Installation 7.3.1. Introduction (continued –2/2)  Figure 7-4  Overall Connections
AE–1800 Instruction Manual Installation 7.3.2.  Connector Pin Assignments and Connections  The pin assignments of the connectors and connections to the pins are illustrated below.  ①  Power Supply Receptacle  Figure 7-5    Power Supply Receptacle (Front View)           ・  Mating Female Type Plug: 14–P3F    The power cable supplied is approx. 3 meters long and is of two–wire shielded type, normally terminated in a 3–hole female type plug at one end, with 3 conductors  open–ended each at the other end. Exercise CAUTIONS 1 below.    After pushing the plug into the above receptacle and tightening its coupling ring, connect the three conductors as follows:  ・  Black conductor:    to negative ( – ) terminal of ship’s power source  ・  White conductor:  to positive ( + ) terminal of ship’s power source (*124 VDC)  ・  Shield ( braid):  to ship’s earth ground   *1Nominal input voltage. The equipment operates safely over the 11–to–40V range.  < CAUTIONS >   1. The DC power cable specified for use with the F–2000/F–3000W or DEBEG 4620/DEBEG 4630 cannot be plugged into the above receptacle.  2.  Reversing the power cable polarity (black and white connections) causes the fuse to blow.  ②  Cabinet Ground Terminal  Figure 7-6    Cabinet Ground Terminal    The receiver cabinet, which is electrostatically coated inside, can be grounded to the vessel’s earth ground without grounding the negative line of the ship’s power source. In situations where it is required, or desirable, to ground the cabinet for safety reasons or *2EMC compliance, connect from this terminal to an appropriate earth ground in the vessel using a thick wire. The ground wire should be as short as possible to reduce the chance of picking up interference from other onboard electronics.  *2EMC = electromagnetic compatibility (continued on next page) Pin # 1 (*124V+) Pin # 2 ( –) Pin # 3 (Ground )
AE–1800 Instruction Manual Installation 7.3.2.  Connector Pin Assignments and Connections (continued – 2/8)  ③ Fuse Holder   Figure 7-7 Fuse Holder   A 3–ampere (3A) cartridge fuse (5.2X20 mm, slow–blow type) is inserted in the holder.    Reversing the power cable polarity causes the fuse to blow.  < WARNING >   AN INCORRECTLY RATED FUSE OR INCORRECT TYPE FUSE WILL BLOW AT POWER–UP OR WILL NOT PROTECT THE EQUIPMENT IN THE REMOTE EVENT OF A TROUBLE OVERLOADING ITS POWER SUPPLY.    ④  Antenna Receptacle (BNC) for Active Antenna ANT–2000M    Figure 7-8 Antenna Connector for ANT–2000M   Plug the ANT–2000M three–frequency active antenna into this connector receptacle.     ・ Mating Plug: BNC–58/U or equivalent   < WARNING >   THE CENTER CONDUCTOR OF THE BNC RECEPTACLE IS AT 8V/12V+ WHEN THE EQUIPMENT IS TURNED ON. DO NOT SHORT THE CENTER CONDUCTOR TO GROUND OR DAMAGE TO INTERNAL PARTS MAY RESULT.     NOTE: Use of Long Wire Antenna   Since this input connector is designed to impedance–match the active antenna unit (50Ωnominal), it is not suitable for connection to a wire antenna that requires a high input impedance for good results. However, if you wish to use a long wire antenna as an emergency backup, be sure to insulate the other end of the wire to avoid short–circuiting the preamplifier power supply (8V or 12V) to ground.             ANT +8V/12V at center conductor
AE–1800 Instruction Manual Installation 7.3.2.  Connector Pin Assignments and Connections (continued – 3/8)  ⑤ RS–422 Connector   Connections from an IBS/INS device are to be plugged into this receptacle. A D–Sub 9 female type plug mates with this connector. The pin assignments are illustrated below.  Figure 7-9    RS–422 Connector Pin Assignments (Front View)              NOTES:   (1)  This interface consists of a MAX3490 RS–422 transceiver. Brief specs. are given below. For details, see the parts manufacturer’s (MAXIM) data sheets.  - Input High Voltage: 2V (min.), Input Low Voltage : 0.8V (max.)  - Input Current ( signal lines A & B) : 1.0 mA @12V, –0.8 mA@ –7V  - Receiver Input Impedance: 12 kΩ   (2)    Pins #1, #2, #3 and #4: No internal connections (NC)   (3)  Input lines (pins #6 and #7) are insulated from ship’s ground by opto–isolators.   ・ Mating Plug: HDEB–9S (supplied) or equivalent    After making connections, check to be sure that the RS–422 port is enabled (as per paragraph 4.12.2) and that a correct set of parameters is selected (as per paragraphs 4.12.3 and 4.12.4) for your applications.   The command formats used to control communications with an INS/IBS device are given in paragraph 7.4.              (continued on next page) Pin #1 (NC) Pin# 5 (GND) #6 ( RX+), Sig. Line A #9 (TX–), Sig. Line B #7 ( RX–), Sig. Line B #8 ( TX+), Sig. Line A
AE–1800 Instruction Manual Installation 7.3.2.  Connector Pin Assignments and Connections (continued – 4/8)  RS–422 Transceiver Data Sheet – 1/3
AE–1800 Instruction Manual Installation 7.3.2.  Connector Pin Assignments and Connections (continued – 5/8)  RS–422 Transceiver Data Sheet – 2/3
AE–1800 Instruction Manual Installation 7.3.2.  Connector Pin Assignments and Connections (continued – 6/8)  RS–422 Transceiver Data Sheet – 3/3
AE–1800 Instruction Manual Installation 7.3.2.  Connector Pin Assignments and Connections (continued – 7/8)  ⑥ RS–232C Connector   An optional serial printer (PR–900) is to be plugged into this receptacle. A D–Sub 9 female type plug mates with this connector. The pin assignments are illustrated below. Figure 7-10    RS–232C Connector Pin Assignments (Front View)             NOTE: Pins #1, #4, #5, #6, #7, #8 and #9: No internal connections (NC)  ・ Mating Plug: HDEB–9S (supplied) or equivalent    After making connections, check to be sure that the RS–232C port is enabled (as per paragraph 4.12.2) and that a correct set of parameters is selected (as per paragraphs 4.12.3 and 4.12.4) for your applications.  Connections to PR–900   The connections from the RS–232C port to the PR–900 serial printer are illustrated below. A 2–meter cable, terminated in appropriate mating plugs at both ends is normally supplied with each printer.  Figure 7-11    Connections between RS–232C Port and PR–900            Port Parameter Settings for PR–900  The PR–900 requires the following parameter settings for the RS–232C port:  ・ DATA BITS:  8  ・ STOP BITS:  1  ・ PARITY:   NONE  ・ BIT RATE: 0.11 (=110 baud)   See paragraph 4.12 for detailed instructions.    Flow Control for Other Brand Printers   If other brand serial printer (e.g. SEIKOSHA DPU–414) is to be connected, be sure to disable its hardware flow control, and set the flow control to “X–ON/X–OFF.” The AE–1800 does not support a handshaking protocol. (continued on next page) Pin #1 (NC) Pin # 2 ( RXD) Pin # 3 ( TXD) Pin# 5 (GND) Pin # 6 ( NC) Pin # 9 (NC) CP111–8P
AE–1800 Instruction Manual Installation 7.3.2.  Connector Pin Assignments and Connections (continued – 8/8)  ⑦ I/O DATA Connector  The I/O DATA port is primarily for data communications with other onboard devices using IEC 61162–1 (NMEA–0183 ) as the interface. It also provides a port (comprising pins #4, #5 and #6) for software updating, and a regulated 12V DC 200 mA output for powering light–duty applications.  Figure 7-12    I/O DATA Connector Pin Assignments (Front View)            ・ Mating Plug: CP111–8P or equivalent (supplied)  < WARNINGS > 1. PINS #4, #5 AND #6 ARE TO BE USED EXCLUSIVELY FOR THE SPECIFIED PROGRAMMING TOOL. CONNECTING ANY OTHER DEVICE TO THESE PINS CAUSES THE EQUIPMENT TO BE LOCKED UP. 2.  CURRENT DRAIN FROM PIN # 7 MUST NOT EXCEED 200 MILLIAMPS.  ⑧ ALARM Output Connector   The ALARM output connector provides an open/close (make/break) switch simultaneously via two pairs of replay contacts, electrically isolated from each other and from the equipment circuitry, when the message alarm is activated. This connector is to be used to activate an alarm sounder mounted at a remote location. The pin assignments are given below.    To connect an external alarm device, use pins #1–#2 pair or pins #3–#4 pair.  Figure 7-13    ALARM Output Connector Pin Assignments (Front View)           ・ Mating Plug: CP111–4P or equivalent (supplied)    NOTE: Alarm messages compliant with IEC 61162–1 $CRARL sentence format are available from the RS–422 (INS) port, and not from this connector. Pin #1 (Alarm 1) Pin #2 (Alarm 1) Pin #3 (Alarm 2) Pin #4 (Alarm 2) #1 ( IEC 61162 In + ), Sig. Line A #2 ( IEC 61162 In – ), Sig. Line B #3 ( IEC 61162 Out + ), Sig. Line A #4 ( Reserved for software updating)#5 ( Reserved  for softwareupdating) #6 ( Reserved for softwareupdating) Pin # 7 ( +12V,  200 mA ) #8 ( IEC 61162 Out – ) ,S. Line B
AE–1800 Instruction Manual Installation 7.4.  INS Port Data and Command Sentences The equipment supports the following IEC 61162–1 data sentence formats for communications with an INS / IBS system via the RS–422 port. It is assumed that the port is set to “ON” via the procedure given in paragraph 4.12.2.2.  7.4.1.  Received NAVTEX Sentence Format The first line of a NAVTEX message text will be output in the following format: $CRNRX,XXX,XXX,XX,aaXX,X,,,,,X.X,X.X,A,c-----c*hh<CR> <LF>  ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩  ① Number of sentences 001 – 999 ②  Sentence number 001 – 999 ③  Sequential message number 00 – 99 (used to uniquely identify messages of same ID) ④  NAVTEX message ID characters (B1, B2, B3, B4) ⑤ Frequency index: 0= not received over air, 1= 490 kHz, 2 = 518 kHz, 3 = 4209.5 kHz ⑥  Null fields (UTC, day, month and year data characters not available. See NOTE 1.) ⑦  Total number of characters in this series of NRX sentences ⑧  Total number of bad characters ⑨ Status indication:  ・  Status “ A”= reception of NAVTEX message in correct format  ・  Status “ V”= reception of NAVTEX message in incorrect format ⑩  Message body (first line of message text characters). A forced carriage return () on screen will be replaced with an underscore ( _ ) (hex 5F ) when it is output. See NOTE 2 for information on the output format for undefined ASCII characters (IEC 61162–1, paragraph 5.1.3)  The data characters in fields  ④,  ⑤,  ⑥,  ⑦,  ⑧ and ⑨  are output in the first message line only; they are null fields in the subsequent message lines, as shown below.  $CRNRX,XXX,XXX,XX,,,,,,,,,,c-----c*hh <CR> <LF>  NOTES: 1:   The equipment does not have a built–in realtime clock (RTC) and does not interface with a GPS sensor. Therefore, the UTC, day, month and year data characters are output as null fields. To check message aging, an internal time reference derived from the CPU clock (24.00 MHz) by frequency division is used. 2:   Undefined characters used in a displayed/stored NAVTEX message are communicated to the INS port in hexadecimal form using code delimiter (^, hex 5E) as follows:  ・ *1Comma ( , ):     ^2C  ・ *2Error character asterisk ( * ): ^2A  ・ Carriage return <CR > and line feed < LF >:   ^0D ^0A  *1: To discriminate from field delimiter  *2: To discriminate from checksum field delimiter  An example INS output of a NAVTEX message is given below.  (continued on next page)
AE–1800 Instruction Manual Installation 7.4.1.  Received NAVTEX Sentence Format (continued –2/2)  An example 518 kHz NAVTEX message text is given below.  IB45 260909 UTC MAR 07 WWJP83 RJTD 260600 VITAL WARNING FOR YOKOHAMA NAVTEX AREA 260600UTC ISSUED AT 260900UTC COLD FRONT FROM 48N 157E TO 42N 156E 36N 151E 30N 147E 25N 140E GALE WARNING WESTERN SEA OFF SANRIKU WITH MAX WINDS 35 KNOTS WARNING(NEAR GALE) EASTERN SEA OFF SANRIKU, NORTHERN SEA OFF KANTO, SOUTHERN SEA OFF KANTO, EASTERN SEA OFF TOKAI NEXT WARNING WILL BE ISSUED BEFORE 261500UTC =  NNNN   The INS port output from the above message consists of 11 NRM sentences, numbered 001 through 011, (message ID = IB45, *1total characters=426 with no corrupt characters) as follows:  $CRNRX , 011 ,001 ,15 ,IB45,2,,,,,426,0,A,IB45^0D^0A260909 UTC  MAR  07^0D^0AWWJP83 *02 $CRNRX ,011,002 ,15 ,,,,,,,,,,RJTD 260600^0D^0AVITAL WARNING FOR YOKOHAMA NAVTEX*03 $CRNRX ,011,003 ,15 ,,,,,,,,,, AREA^0D^0A260600UTC  ISSUED  AT  260900UTC^0D^0ACOLD*69 $CRNRX ,011,004 ,15 ,,,,,,,,,, FRONT  FROM 48N 157E T O  42N 156E  36N^0D^0A 151E  30*1F $CRNRX ,011,005 ,15 ,,,,,,,,,,N 147E 25N 140E^0D^0AGALE  WARNING WESTERN  SEA  OFF *70 $CRNRX ,011,006 ,15 ,,,,,,,,,,SANRIKU ^0D^0AWITH  MAX  WINDS 35  KNOTS^0D^0AWARNING*0E $CRNRX ,011,007 ,15 ,,,,,,,,,,(NEAR GALE)  EASTERN  SEA  OFF ^0D^0ASANRIKU^2C  NORTH*0E $CRNRX ,011,008 ,15 ,,,,,,,,,,ERN  SEA  OFF  KANTO^2C^0D^0ASOUTHERN SEA OFF  KANTO*16 $CRNRX ,011,009 ,15 ,,,,,,,,,,^2C  EASTERN  SEA  OFF ^0D^0ATOKAI^0D^0ANEXT  WARNING *10 $CRNRX ,011,010 ,15 ,,,,,,,,,,WILL BE ISSUED  BEFORE ^0D^0A261500UTC^0D^0A =^0D^0A*07 $CRNRX ,011,011 ,15 ,,,,,,,,,,^0D^0ANNNN^0D^0A  *41  *1: Total characters include carriage return (CR) and line feed (LF) codes.
AE–1800 Instruction Manual Installation 7.4.2.  Controlling Receiver Operation via INS (RS–422) Port  To externally control receiver operation via the RS–422 port, the equipment supports the following command sentence (IEC 61162–1 format). Up to 10 commands will be stacked and executed sequentially. Using the transmitter mask and message mask, the user can select the station IDs and message types for message storage in the non–volatile memory, for message output to the RS–422 port (INS port) or to the RS–232C port (printer port). Message types A, B, D and L, however, cannot be rejected. Previous selection/rejection settings manually entered via the keypad will be changed accordingly.  $--NRM,X,X,hhhhhhhh,hhhhhhhh*hh <CR> <LF>   ①        ② ③ ④ ⑤ ⑥  ①  Device identifier (e.g. IN=INS device, AI=AIS) ②  Function code: 0 to 9   0 = request messages, 1 = set/report storage mask, 2= set/report printer mask   3 = set/report INS mask, 4 to 9 = reserved ③  Frequency index: 1 to 9   1= 490 kHz, 2 = 518 kHz, 3 =4209.5 kHz, 4 to 9=  reserved   CAUTION: If the index for the second receiver that is not currently selected is specified, the command will be ignored. ④  Transmitter ID mask in hex (32 bits in total)   LSB = station A, bit 1 = station B, bit 25 =   station Z,    bits 26 to 32 = reserved   To select a station, its corresponding bit should be set to “ 1.” To reject a station, its corresponding bit should be set to “0.”       For example, to select only stations E, J, M and T for storage, or output to the INS or printer port, set the transmitter ID masks as follows:  00081210 hex  0 0 0 8 1 2 1 0 (hex)  0000 0000  0000 1000  0001  0010  0001 0000 (binary)    ZY  XWVU TSRQ PONM LKJI HGFE DCBA (station)  ⑤  Message type mask in hex (32 bits in total):   LSB = type A, bit 1= type B,  bit 25 = type Z,    bits 26 to 32 = reserved   To select message types only A, B, D, F and L for storage or output to the INS or printer port, set the message ID masks as follows:  0000082B hex  0 0 0 0 0 8 2 B (hex)  0000 0000  0000 0000  0000  1000 0 010 10 11 (binary)    ZY  XWVU TSRQ  PONM LKJI HGFE  DCBA (type)   NOTE: Message types A, B, D and L must always be selected due to the relevant IMO resolution, and their corresponding bits cannot be set to “0.”  ⑥  Checksum in hex   The checksum value must be calculated by the user.  The current settings can be checked by a query command described in next paragraph.
AE–1800 Instruction Manual Installation 7.4.3.  Checking Current Settings via INS (RS–422) Port  The equipment accepts the following query command sentence via the RS–422 port (INS port), and reports to the user the current B1B2 mask settings, indicating the status of message storage in the non–volatile memory, and message output to the INS port and the RS–232C port (printer port) for all frequencies.  $ - - CRQ,NRM*hh<CR><LF>  ① ②  ①  Device identifier (e.g. IN=INS device, AI=AIS)  ② Checksum in hex   Example: Device identifier = IN (INS device), checksum= 3A hex  $ INCRQ,NRM*3A<CR><LF>   A total of nine output sentences will then be sent back to the INS device like the examples below.   $CRNRM,1,1,03FFFFFF,02200EBF*32:  Settings for 490 kHz, to non–volatile memory $CRNRM,2,1,03FFFFFF,02200EBF*31:  Settings for 490 kHz, to printer port $CRNRM,3,1,03FFFFFF,02200EBF*30:  Settings for 490 kHz, to INS port $CRNRM,1,2,03FFFFFF,02200EBF*31:  Settings for 518 kHz, to non–volatile memory $CRNRM,2,2,03FFFFFF,02200EBF*32:  Settings for 518 kHz, to printer port $CRNRM,3,2,03FFFFFF,02200EBF*33:  Settings for 518 kHz, to INS port $CRNRM,1,3,03FFFFFF,02200EBF*30:  Settings for 4209.5 kHz, to non–volatile memory $CRNRM,2,3,03FFFFFF,02200EBF*33:  Settings for 4209.5 kHz, to printer port $CRNRM,3,3,03FFFFFF,02200EBF*32:  Settings for 4209.5 kHz, to INS port  NOTE: The above examples represent the default mask settings.
AE–1800 Instruction Manual Installation 7.4.4.  Alarm Output Sentence Formats  7.4.4.1.  Output Format for Alarm Being Activated  An alarm output sentence like the example below will be output to the RS–422 (INS) port when the equipment receives an alarm NAVTEX message or if the equipment develops a failure or malfunction. The output will be repeatedly available at 30–second intervals until the alarm condition is acknowledged and reset manually by pressing twice*1 on the equipment or until the appropriate acknowledgement command (paragraph 7.4.5) is fed via the port from the INS terminal.  $CRALR,,003,A,V,NAVTEX:Search and Rescue information*72<CR><LF>    ① ② ③ ④ ⑤  NOTE: The equipment does not use UTC as the time source, and therefore sends a null field in place of the time–of–alarm–condition–change field.  ① Local alarm number:   001 = Navigational warning (type–A message)   002 = Meteorological warning ( type–B message)   003 = SAR, piracy, armed robbery information (type–D message)  004 = Receiver malfunction   005 = Self–diagnostic test failure  006 = General failure ② Alarm conditions:   A= threshold exceeded ( i.e. alarm condition exists )   V= threshold not exceeded (i.e.  alarm condition is non–existent ) ③  Alarm acknowledgement status  A= acknowledged  V= unacknowledged ④  Alarm description text ⑤ Checksum   03 = Navigational warning   0F = Meteorological warning   72 = SAR, piracy and armed robbery information  The other alarm output sentences are as follows:  $CRALR,,001,A,V,NAVTEX:Navigational warning*03<CR><LF> $CRALR,,002,A,V,NAVTEX:Meteorological warning*0F<CR><LF> *1: Pressing the key once silences the audible indication alone, allowing the output sentence to continue every 30 seconds.    A second keypress resets all the currently active alarms.  7.4.4.2.  Output Format for Alarm Being Acknowledged When active alarms are acknowledged, the following sentences will be output once:  $CRALR,,001,V,A,NAVTEX:Navigational warning*03<CR><LF> $CRALR,,002,V,A,NAVTEX:Meteorological warning*0F<CR><LF> $CRALR,,003,V,A,NAVTEX:Search and Rescue information*72<CR><LF>
AE–1800 Instruction Manual Installation 7.4.4.3.  Output Format After Alarm Being Acknowledged Within one minute after the issuance of the above sentences or after the key is pressed twice, the following outputs will be repeated at one–minute intervals. This condition will continue until another alarm message is received.  $CRALR,,001,V,V,NAVTEX:Navigational warning*14<CR><LF> $CRALR,,002,V,V,NAVTEX:Meteorological warning*18<CR><LF> $CRALR,,003,V,V,NAVTEX:Search and Rescue information*65<CR><LF>  7.4.5. Alarm Acknowledgement The following command format is supported to acknowledge and reset the current alarm condition via the RS–422 (INS) port: $– –ACK,003*hh<CR><LF>  ① ② ③  ①  Device identifier (e.g. IN=INS device, AI=AIS) ② Local alarm number  001 = Navigational warning  002 = Meteorological warning   003 = Search and rescue (SAR) information ③ Checksum:   If the device identifier is IN (INS device), for example, the above command format for each alarm is as follows:  $INACK,001*53<CR><LF> :    to acknowledge Navigational warning  $INACK,002*50<CR><LF> :    to acknowledge Meteorological warning  $INACK,003*51<CR><LF> :    to acknowledge SAR information  7.4.6.  Proprietary Sentence (Switching 2nd Receiver Frequency) The following command (I E C 61162–1 proprietary format sentence) is used to externally switch the second receiver frequency between 490 kHz and 4209.5 kHz:  $PJMCR, 0, 1 *hh <CR> <LF>    ① ② ③ ① Receiver index:   0 = Second receiver   1 to 9 = Reserved ②  Receive frequency index:   1 = 490 kHz   2 =  Not assigned   3 = 4209.5 kHz ③ Checksum:   See the examples below.  Examples: To switch the frequency, an INS device should send the following command sentences to the equipment via the RS–422 port: ・  Switching to 490 kHz:      $PJMCR,0,1*47<CR><LF> ・  Switching to 4209.5 kHz:    $PJMCR,0,3*45<CR><LF>
AE–1800 Instruction Manual l Theory of Operation  8.  Summarized Theory of Operation  8.1. What is NAVTEX? NAVTEX, a system of broadcast and automatic reception of global maritime safety information by means of direct display/printing telegraphy, is part of the *1GMDSS infrastructure, defined by *2IMO Assembly resolution A.706 (17). Broadcasting is accomplished by a worldwide network of dedicated coastal stations regularly sending weather information, navigational warnings, search–and–rescue (SAR) information and other related messages, all in an easy–to–read text format, to mariners free of charges.  8.2. Operating Frequencies At present three frequencies are officially allocated by the *3ITU for NAVTEX broadcasting service: 518 kHz, 490 kHz and 4209.5 kHz. All *4SOLAS convention vessels are required to carry a receiver dedicated to receiving NAVTEX transmissions automatically on all the above frequencies. Transmissions on 518 kHz are in English and of general interest to vessels navigating international waters, while the 490 kHz service is primarily targeted at those working most of the time in areas close to transmitting stations, providing more localized information in national languages. Some stations also broadcast information to local users on 4209.5 kHz. Stations on each frequency transmit NAVTEX messages usually for a period of 10 minutes on a time–sharing basis to avoid cross–station interference.  8.3. Service Area The coverage area of a 518 kHz station is normally 200 to 400 nautical miles in daytime hours, depending on the transmitting power level, and a signal travels along the surface. At night some of the signal often travels more than double the daytime coverage by being reflected a number of times between the surface and the ionosphere, a band of ionized atmospheric layers 50 to 400 km above the surface. The 490 kHz service area is less than the 518 kHz coverage due to lower transmit power levels, but the nighttime coverage often extends greatly due to ionospheric reflections. The 4209.5 kHz broadcast, though catering mainly for inshore users and covering much less areas in the daytime, can be received from more than 1000 miles away during hours of darkness.  8.4. Error Correction Signal propagation conditions constantly vary with time of the day and also with the season. The signal arriving at the receiver can be corrupted or distorted at any time by static discharges, natural noise, abnormal solar activity, unstable ionospheric conditions, interference between the signal coming directly from the transmitter and the one reflected from the ionosphere, etc. It is therefore likely that a vital NAVTEX message can be missed due to signal corruption or distortion at the receiving end.  In order to ensure that each message is properly received within its intended area of coverage, a station sends out the same message twice, some hours apart, each with its   identification code (known as B1 character), message type code (B2 character) and a two–digit serial number (B3B4, ranging 00 to 99). In addition, the system employs a mode of transmission called forward error correction (FEC), transmitting each alphanumeric character in the message twice at very short intervals. If the same character is received twice, the receiver considers it to be a true character. If either of the received characters is different or corrupted, the receiver treats it as an invalid letter, and displays or prints an asterisk (*) in its place, thereby securing the reliability of a received message. (continued on next page)
AE–1800 Instruction Manual l Theory of Operation  8.    Summarized Theory of Operation (continued – 2/10 )  8.5.  NAVTEX Receiver – General A NAVTEX receiver that complies with the relevant IMO resolutions and regulations for wheel mark certification is programmed to automatically receive and display/print a message, and avoids a repeated reception of the same message by checking the ID and numbering of each message. Using the ID and message type data attached to each message, the user can also program the receiver to reject certain transmissions and message types that are not of importance while in the current area, except for SAR and other urgent warning messages classified as type D messages.  An audible and visual alarms are automatically triggered upon reception of such a message. To silence the alarm, the user must manually, or via an appropriate command from an INS terminal, acknowledge the message arrival. Received messages are either printed on paper (for a receiver with a built–in printer) or displayed on a screen with memory for storage and retrieval (for a receiver with an integral LCD screen).   8.6. The AE–1800 NAVTEX Receiver The AE–1800 receiver has two built–in receivers on the same receiver board, with the first receiver devoted to receiving 518 kHz broadcast at all times and the second receiver receiving either 490 kHz or 4209.5 kHz signal as selected by the user through the menu system. Received messages are displayed across an 8–inch liquid crystal display (LCD) and stored permanently or temporarily as specified by the user.    Up to 200 messages, each with an average of 500 characters, received on the first and second receivers are separately stored and then automatically erased from memory 60 hours after the time of reception on a first–in–first–out basis. However, up to 25 messages can be protected against automatic erasure, and are stored in a separate area of the non–volatile message memory, in which case an additional 50 new messages can be stored in memory for each receiver.  When a transmission occurs on the first and second receiver frequencies at the same time, the equipment receives both signals, displaying the first receiver message while storing the second receiver message in memory for later retrieval. An appropriate caution message shows up in the screen bottom prompt line to indicate the reception of a new NAVTEX message on the second receiver.  Reception of a type–D message (SAR, piracy and armed robbery information) activates the audible and visual alarms. The received message text then is shown in red, making it easy to discriminate it from navigational (type–A) and weather (type–B) warnings. The audible alarm also sounds differently to indicate that a type–D message has been received. The alarm can be acknowledged remotely by an IBS/INS terminal connected to the RS–422 port on the rear panel. When a type–D message is received on the second receiver alone, the display automatically switches to the second receiver page, showing its message in red while sounding the alarm in the same manner as on the first receiver.  The stored messages can be output via three interface ports mounted on the rear panel for IBS/INS or other onboard applications The user can specify the ID, frequency and type of the messages you wish to output.    An optional printer can also be plugged in to print the current message in real time or those recalled from the non–volatile memory.   *1: Global Maritime Distress and Safety System,    *2: International Maritime Organization *3: International Telecommunications Union,    *4: Safety of Life at Sea (continued on next page)
AE–1800 Instruction Manual l Theory of Operation  8.  Summarized Theory of Operation (continued – 3/10)  8.7. Operating Principle of AE–1800  Figure 8–1 shows interconnections between the printed circuit boards (PCBs) comprising the AE–1800  system and interface connections from the PCBs to data input/output ports and peripheral devices. A functional block diagram of the receiver PCB is given in Figure 8–2..  To follow the circuit description below, see also the block diagram and schematics of the receiver PCB and Main PCB attached.  Receiver Circuit To receive the three NAVTEX frequencies (518 kHz, 490 kHz and 4209.5 kHz), the system incorporates two independent receivers (first and second receivers) plus a local oscillator that is switched into operation when the second receiver frequency is changed to 4209.5 kHz. All receivers are mounted on the receiver PCB (S602–RCV–A).  Both 518 and 490 kHz signals picked up at the *active antenna’s preamplifier pass through a bandpass filter (L4, L19) and are then amplified by a common RF amplifier (Q4).  *The active antenna contains three passband filters, independently tuned to the three frequencies, each followed by a single stage preamplifier. The 490 kHz filter and 4209.5 kHz filter are switched by a relay when the second receiver frequency is changed.  The amplified signals are then separately filtered by crystal filters (F1 for 518 kHz, F2 for 490 kHz) to avoid cross–channel interference and reject interference adjacent to each frequency.  A 4209.5 kHz signal goes through its devoted bandpass filter (L3, L6). After being amplified by RF amplifier Q5, it is fed to a diode mixer (D3, D4), which converts the 4209.5 kHz signal into a 490 kHz signal through heterodyne action using a local oscillator output (3719.5 kHz) derived from crystal oscillator U3 (29.756 MHz) through a divide–by–8 frequency divider (embedded in U3’s package). The 490 kHz output is then fed to the 490 kHz crystal filter F2 through a switch (U1, Q6).  After passing through the appropriate crystal filter, each signal is again amplified (by Q10 for 518 kHz, Q11 for 490 kHz) and then fed to an FM detector ( U9 for 518 kHz, U10 for 490 kHz), which demodulates a frequency–shifted (carrier±85 Hz) RF NAVTEX signal into a stream of baseband pulses at 100 baud using quadrature detection technique. The detected output is then fed to the CPU via a lowpass filter and comparator chain (U11 for 518 kHz, U12 for 490 kHz) and an opto–isolator (K7 for 518 kHz, K8 for 490 kHz).  To test whether each receiver is functioning properly, two NAVTEX signal generators are provided on the same PCB, each consisting of crystal–controlled oscillator (U5 for first receiver, U4 for second receiver) and common divide–by–16 frequency divider U2. When the self–diagnostic test function is activated via the menu, each generated signal will be mixed by diode mixer D5 with the 3719.5 kHz output from local oscillator U3, producing test signals at 518 kHz and 490 kHz. They will then be fed to their respective amplifiers in the same manner as live NAVTEX signals are processed.  (continued on next page)
AE–1800 Instruction Manual l Theory of Operation  8.  Summarized Theory of Operation (continued – 4/10 )  8.7.  Operating Principle of AE–1800 (continued –2 / 2)  CPU Circuit The Main PCB (M613–MAIN–X) carries a CPU circuit and a power supply circuit. The CPU is a 16–bit single–chip microcomputer (U10) clocked at 24 MHz by crystal–controlled oscillator X1, and on–chip flash ROM for program software and on–chip RAM providing memory space for data processing of the demodulated signals.  An external static RAM (SRAM) chip (U5, 512 kB) is mounted for the storage of messages and IDs, and is backed up by large capacity capacitor C6 (1.0 farad) for approx. 10 days in the event the unit is placed in a continuous power–off condition. A portion of the memory capacity is allocated as a video RAM (VRAM) to hold text for display on the LCD screen.  U3 is factory–programmed to act as a display controller to perform various display control functions and text scrolling. The input/output interface between the CPU and externally connected devices consists of three external ports: U4 for the RS–232C and   I/O DATA ports, U12 for the RS–422 port.   Power Supply Circuit The power supply circuit consists mainly of a switch–mode voltage regulator (U55), a power transformer (T51), a DC–to–DC converter (U52) (or U57 3–terminal voltage regulator) and a 3–terminal voltage regulator (U56), producing various regulated outputs (3.3V for IC chips,  ±12V for RS–232C port, +12V for the receiver PCB, +5V for RS–422 port, etc.) required for operation of the entire Main PCB circuitry. The voltages (+8V and +5V) required for receiver operation are derived from the +12V output through 3–terminal regulators (U7 and U8) on the receiver board.  Should the power line polarity be reversed accidentally, diode D51 will cause the fuse F1 (3A) to blow, thereby protecting the input circuit from possible damage. A varistor (VA51) is placed across the DC input line to protect the power supply circuit from possible damage in the event voltage transients on the ship’s power line voltage exceed 40V.
AE–1800 Instruction Manual l Theory of Operation  8.    Summarized Theory of Operation (continued – 5/10)  Figure 8-1  Interconnections                                                  (continued on next page)
AE–1800 Instruction Manual l Theory of Operation  8.    Summarized Theory of Operation (continued – 6/10)  Figure 8-2    Functional Block Diagram – Receiver Board
AE–1800 Instruction Manual l Theory of Operation  8.    Summarized Theory of Operation (continued – 7/10)  Figure 8-3 CPU Circuit – Main Board
AE–1800 Instruction Manual l Theory of Operation  8.    Summarized Theory of Operation (continued – 8/10)  Figure 8-4 Power Supply Circuit – Main Board
AE–1800 Instruction Manual l Theory of Operation  8.    Summarized Theory of Operation (continued – 9/10)  Figure 8-5 LCD Backlight Control Circuit – Main PCB
AE–1800 Instruction Manual l Theory of Operation  8.    Summarized Theory of Operation (continued – 10 / 10)  Figure 8-6 Keypad Board
AE–1800 Instruction Manual Specifications 9. Specifications  (1)  IEC 60945–2002 Equipment Category:  ・ Receiver Cabinet:  Protected  ・ Active Antenna Unit:  Exposed (2) Receive Frequencies:  ・ First Receiver:  518 kHz  ・ Second Receiver :  490 kHz and 4209.5 kHz, front panel–selectable or by *1proprietary command sentence via RS–422 port (3)  Type of Receiver:  ・ First Receiver:  518 kHz straight amplifier  ・ Second Receiver:   - 490 kHz:  490 kHz straight amplifier   - 4209.5 kHz:  Down–conversion to 490 kHz (4) Antenna Input:  Coaxial: 50 Ω(nominal),  matched with ANT–2000M active antenna (5) Input Protection:  30 VRMS for 15 minutes over 100 kHz–28 MHz range (6) Active Antennas:  ・Standard:  Preamplified 1.2m glass–fiber whip (ANT–2000M) for reception of 518 kHz, 490 kHz and 4209.5 kHz, with 1–meter RG–58/U coaxial cable attached, terminated in BNC and PL–259 plugs for cable extension. (7) Message Display:  5.7” (diagonal) color TFT, QVGA (320X240 pixels)  (8). Receiver Sensitivity:  Better than the following value for message reception with character error rate (CER) of less than 4%:    ・ 1 μV e.m.f. to coaxial input (9) Demodulator:  Quadrature detector, crystal–controlled  (10) Mode of Reception :  F1B with forward error correction (AnnexⅡ to ITU–R REC. 476–3, M.540–2 and 625 B–mode)  ・ Single Frequency:  Automatic reception and display of message transmitted on 518 kHz or on user–selected second receiver frequency (490 kHz or 4209.5 kHz)  ・ Dual Frequency:  Automatic, simultaneous reception of 518 kHz and user–selected second receiver frequency (490 kHz or 4209.5 kHz), with automatic display of first receiver’s live messages while storing second receiver messages in memory when NAVTEX broadcasts occur at both frequencies simultaneously.  (11) Second Receiver Selection:  490 kHz or 4209.5 kHz selectable via menu system or *1proprietary command sentence via RS–422 port   *1:See paragraph 7.4.6 for detail. (12) Source of Time:  Derived from CPU clock 24.00 MHz for calculation of time passage to handle message aging. No real time clock (RTC) is used.  (13) User Interface Language:  English ( menus, status, prompts, cautions)   (continued on next page)
AE–1800 Instruction Manual Specifications 9. Specifications (continued – 2/4)  (14) Text Display:  ・ NAVTEX Messages:  40 characters per line, 18 lines per screen. A forced carriage return symbol *2()  divides the last word at 40th character position if the number of character in a line exceeds 40.  Maximum capacity of characters/line: 4096  *2 Hex 5F ( _ ) is output to RS–232C or RS–422 port.  ・ Statuses & Prompts:  1 line (40 characters maximum) at screen’s upper and lower edges (15)  Indication of Message Reception and Storage  ・ Message Reception:  Tag iNEW MESSAGEi is attached to message ID.  ・ Storage:  Indication “STORED” is turned on at the end of each satisfactorily received message together with a character error rate (CER= XX%) readout (16) Message Scrolling:  ・ Live Messages:  Automatic, except for new SAR messages  ・ Stored Messages:  Manual, line–by–line or page–by–page scrolling (17) Message Storage:  ・ Capacity:  200 messages (average 500 characters per message) for each of 518 kHz, 490 kHz and 4209.5 kHz receivers. Up to an additional 50 messages  can be stored (for 518 kHz and 490 kHz or 4209.5 kHz) if stored messages are protected.     Maximum storage of characters: 106,496/frequency     Maximum characters/message: More than 8000     If the equipment receives a message with a character error rate (CER) of > 4% and  ≦ 33%, it will store the message but will receive the same message to be transmitted subsequently. If the subsequent message has a lower CER, it will automatically replace the previously stored one. If a message is received with a CER > 33%, it will not be stored.  ・ Duration:  60 hours 20 minutes from successful reception of each message, or until the storage limit is reached, after which old messages will be automatically erased from memory on a first–in–first–out basis except for user–protected messages that cannot be erased from memory until their protection tags are removed manually. Time source is derived from the CPU clock (24.00 MHz) to compute message aging.  ・Storage without Power:  Protected messages are stored for at least 10 days after power is removed continuously.  (18) Message Protection:  Up to 50 messages on each receiver screen can be protected against automatic erasure, and are saved in a separate area of the non–volatile message memory. Protection of a user–selected message can be cancelled to allow automatic erasure after a 60–hour time passage.    Protected messages are indicated with *3tag iPROTECTEDi attached to the message ID.    *3Removing the tag requires user confirmation. (continued on next page)
AE–1800 Instruction Manual Specifications 9. Specifications (continued – 3/4)  (19) Message ID Storage:  ・ Capacity:  200 IDs of successfully received messages (with CER ≦33%) on each of 518 kHz, 490 kHz and 4209.5 kHz  ・ Duration:  60 hours 20 minutes after receipt or until the storage limit (200 for each frequency) is reached.  (20) Stored Message Outputs:  The following messages can be selectively output via the  RS–422,  RS–232C and I/O DATA ports manually through the menu system or externally with station and message ID mask settings from an INS terminal:    ・ All currently displayed messages or currently displayed messages of user’s choice    ・ All stored messages    ・ Stored messages of user’s choice by specifying frequency, transmitter or message type  (21) External I/O Interfaces:  ・ Printer Interface :  RS–232C port ( MAX3232 transceiver)  ・ IBS/INS :  RS–422 port (MAX3490 transceiver) with input lines optically isolated  ・ NMEA–0183/IEC 61162–1: 8–pin connector (I/O DATA port)  ・ Alarm Activation Output: 2 isolated pairs of relay contacts (ALARM port)  ・ Control Commands:  IEC 61162–1 formatted sentences. Up to 10 commands can be stacked for sequential execution.  (22) Message Alarm Specifications:  ・ Audible Indication:   Beeping from front–facing piezoelectric buzzer     - 1–second intervals: Type D messages     - 3–second intervals: Types, A, B and L messages  ・ Visual Indication:  Red tag iALARM!i attached to ID     ID and message text displayed in red color for type–D messages.  ・ Acknowledgement/Muting:  Manually with front panel button or by means of IEC  61162–1 format command ($- -ACK command) via RS–422 input port.  ・ Alarm Conditions Output:  IEC 61162–1–compliant $CRALR sentences containing local alarm number and alarm text via RS–422 output port. See paragraph 7.4.4 for details.   NOTE : See section 10 (List of Alarms) for additional information on alarms.  (23) Power Requirements:  24 VDC (nominal), approx. 11W. Floating ground. The unit operates safely over a 11–to–40V range.  (24) Cabinet Size & Weight:  238/196 (W) X 217/ 196 (H) X 194 (D) mm  Approx. 2.3 kg with mounting bracket attached  (continued on next page)
AE–1800 Instruction Manual Specifications 9. Specifications (continued – 4/4)  (25)   Compass Safe Distances (in Energized Condition):   ・  Cabinet with Bracket:    60 cm (standard), 35 cm (steering)  ・ Cabinet only:   45 cm (standard), 30 cm (steering)  (26) Ambient Temperatures:  –15 to 55゚C (cabinet, operating)    –40*1 to 70゚C (cabinet, storage)    –25 to 55゚C (active antenna, operating)    –40*2 to 70゚C (active antenna, storage)  (27) Compliance Standards:  IMO Resolution MSC.148(77    IMO Resolution A.694(17)  IEC 61097–6 Ed.2  IEC 60945 Ed.4 (2002)   IEC 61162–1, IEC 61162–2  ITU–R 540–2  ITU–R 625–3  EN 300 065V 1.1.3  EN 301 011V 1.1.1  *1:The temperature must be returned to, and left at –15゚C and above for at least 1 hour, before the equipment can be switched on. *2:The temperature must be returned to, and left at –25゚C and above for at least 1 hour, before the equipment can be switched on.   NOTE: Specifications, other than those specified under the above standards, are subject to change without notice or obligation.
AE–1800 Instruction Manual l List of Alarms 10. List of Alarms  10.1. Message Alarms ●  Alarm for D–Type Message  ・  Enabled /Disabled Status:  Enabled at all times.  ・  Triggering Condition:  To be triggered upon reception of a D–type message.  ・ User Interface:   -  Audible:  Beeping at approx. 1–sec. intervals by alarm buzzer.   - Visual:  Attaching  iALARM!i tag to message ID and displaying both message ID and text in red.  ●  Alarm for A–, B–, and L–Type Messages  ・  Enabled/Disabled Status:  Initially disabled, and can be individually enabled by the user. See paragraph 4.13 for instructions.  ・  Triggering Condition:  To be triggered upon reception of an A–, B– or L–type message.  ・ User Interface:   -  Audible:  Beeping at approx. 3–sec. intervals by alarm buzzer.   - Visual:  Attaching  iALARM!i tag to message ID and displaying message ID in red.  10.2. Operational Alarms ● Storage Limit Alarm:  ・  Enabled/Disabled Status:  Enabled at all times.  ・  Triggering Condition:  To be triggered at time of trying to protect NAVTEX messages for permanent storage in excess of 50.  ・ User Interface:   -  Audible:  Beeping 3 times in quick succession by small buzzer.   - Visual:  Displaying warning “STORAGE LIMIT IS REACHED !” in prompt line at screen’s bottom. ● Memory–Full Alarm:  ・  Enabled/Disabled Status:  Enabled at all times.  ・ Triggering Condition:  To be triggered on reception of additional new NAVTEX message with 199 messages already stored.  ・ User Interface:   -  Audible:  Beeping 3 times in quick succession by small buzzer.   -  Visual:  Displaying warning “ MEMORY FULL! [ CLR ] TO ACKNLG.” in prompt line at screen’s bottom. ● Invalid Keypress Alarm:  ・  Enabled/Disabled Status:  Enabled at all times.  ・ Triggering Condition:  To be triggered when any key not valid for current operation is pressed.  ・ User Interface:   -  Audible:  Beeping 3 times in quick succession by small buzzer.  - Visual:  Displaying warning “INVALID KEYPRESS,” blinking.
AE–1800 Instruction Manual List of Abbreviations 11. List of Abbreviations The abbreviations used in this manual and menus, on screen, control panel and rear panel are listed below. A: amperes ACKNLG: Acknowledge AI:  Automatic identification system (typical device identifier of AIS equipment) AIS:  Automatic identification system ALM: Alarm ALR:  Alarm (header of alarm output sentence from INS port) ANT: Antenna BNC:  Type of coaxial connector BRT:  Brightness control key BSH:  Bundesamt für Seeschiffahrt und Hydrographie (Federal Maritime and Hydrographic Agency, Germany) BV:  Bureau Veritas (France), EU notified body CER:  Character Error Rate (ratio of asterisks to total number of characters) CH:  Operating channel ( receiver currently in use) CLR: Clear key CPU:  Central Processing Unit (core of single–chip microcomputer on CPU PCB) CR:  Communications receiver (device identifier of NAVTEX receiver) CR:  Carriage Return code (0D in hexadecimal notation, unprintable) D: Depth (part of cabinet dimensions) dB: decibels ( unit of relative power strength) DC/AC: DC–to–AC (DC–to–AC voltage inverter for screen backlighting lamp) DIM:  Dimmer key ( for keypad backlighting) DOS/V:  Disk Operating System/V (PC operating system for IBM–compatibles) DRAM:  Dynamic Random Access Memory EMC: Electromagnetic Compatibility EN:  Europäische Norm ( = European Standards) ENT: Entry key F: Frequency FEC:  Forward Error Correction (error–correcting protocol in NAVTEX system) FL : Fluorescent Lamp (screen backlighting lamp) FM: Frequency Modulation FREQ: Frequency FSK:  Frequency Shift Keying (modulation technique for NAVTEX transmission) FWE:  Flash–memory Write Enable (CPU–embedded flash memory programming) F/C: Frequency Converter (used to receive 4209.5 kHz on second receiver) GMDSS:  Global Maritime Distress and Safety System GND: Ground GPS:  Global Positioning System, GPS receiver/sensor H: Height (part of cabinet dimensions) HF:  High frequency band (including 4209.5 kHz second receiver frequency) ID:  Identification code (identification of transmitter) IEC:  International Electrotechnical Commission IMO: International Maritime Organization IN:  Integrated Navigation (device identifier of INS equipment) INS/IBS:  Integrated Navigation System/Integrated Bridge System ISO:  International Standardization Organization I/O: Input/Output kB: kilobytes kg: kilograms LED: Light–Emitting Diode LSB:  Least Significant Bit LST:  Local Standard Time LAT/LON: Latitude / Longitude coordinates LCD:  Liquid Crystal Display LF:  Line Feed code (0A in hexadecimal notation, unprintable)  (continued on next page)
AE–1800 Instruction Manual List of Abbreviations 11. List of Abbreviations (continued – 2/2)  m: meters mA: milliamperes min: minutes mm: millimeters ME or MEM: Memory (non–volatile memory for message storage) MF:  Medium frequency broadcast band (including 490 kHz and 518 kHz) MON: Monitor (audible monitor) MSG: Message (NAVTEX message) MPU: Microprocessing Unit NC: No connection (no internal connection) NMEA:  U.S. National Marine Electronics Association NNNN:  End–of–message indication (specified under IMO/IEC regulations) NRX:  NAVTEX receiver (header of message output from INS port) para.: paragraph PC: Personal Computer PCB:  Printed Circuit Board PR: Printer PWR: Power QVGA:  Quarter VGA ( screen resolution, 320X240 pixels) RAM: Random Access Memory ( embedded in CPU chip) RCVNG: Receiving RCVR: Receiver REC: Recommendation (ITU Recommendation) REF: Reference REJ: Reject, rejected REV: Revision (software revision number) RH: Relative Humidity RJ: Reject, rejected ROM:  Read–Only Memory (embedded in CPU chip) RTC:  Real Time Clock RX: Receive, receiver RMRS:    Russian Maritime Register of Shipping S: Signal SAR: Search And Rescue SEL: Select, selected SIG: Signal SL: Select, selected SOLAS:  Safety of Life at Sea SRAM: Static RAM (non–volatile memory for message storage) STD: Standard compass STG: Steering compass STO: Store TFT:  Thin–Film Transistor ( technology of color LCD ) TX: Transmit, transmitter TXD:  Transmit data (Send data) UTC:  Universal Time Coordinated ( = GMT in common usage) V: volts VCC :  Operating voltage of IC chips used VDC: Volts DC VER: Version ( software version) VGA:  Video Graphics Array ( screen resolution, 640×480 pixels ) W: Width (part of cabinet dimensions ) W: watts WX: Weather XTAL: Crystal (quartz crystal oscillator) Z:  GMT (Greenwich Mean Time)
AE–1800 Instruction Manual User–made Settings 12.  User Settings To Be Stored in Non–Volatile Memory  The following user–made settings will be stored in the non–volatile memory. Settings indicated in Italic type fonts are factory defaults.  ●  Screen Brightness Level:  Last used level  ●  Keypad Dimmer Level:  Last used level  ●  Settings via Menu System  ・ Background Color:   WHITE, BLACK, BLUE  ・  Message Font Type:    NORMAL, BOLD  ・ Screen Sleep Mode   -  On/Off Status:    ON, OFF     -  On/Off Time Period:  STANDARD, USER–DEFINED MODE  ・ *1Second Receiver Frequency: 490 KHZ, 4209.5 KHZ  ・ Keypress Beep:  ON, OFF  ・ *2Station Selection/Rejection Settings (common to first and second receivers)   - Storage in Memory:       Selected Stations:  A to Z  (all stations)       Rejected Stations:  None   -  Output to Printer Port (RS–232C) and I/O DATA port:       Selected Stations:  A to Z  (all stations)       Rejected Stations:  None   -  Output to INS Port (RS–422):       Selected Stations:  A to Z  (all stations)       Rejected Stations:  None   ・ *2Message Type Selection/Rejection (common to first and second receivers)   - Storage in Memory:       Selected Types:  A, B, C, D, E, F, H,J, K, L , V , Z    Rejected Types:  G, I, M,N, O, P, Q, R, S, T, U, W, X, Y   -  Output to Printer Port (RS–232C) and I/O DATA port:       Selected Types:  A, B, C, D, E, F, H,J, K, L , V , Z    Rejected Types:  G, I, M,N, O, P, Q, R, S, T, U, W, X, Y    -  Output to INS Port (RS–422):       Selected Types:  A, B, C, D, E, F, H,J, K, L , V , Z    Rejected Types:  G, I, M,N, O, P, Q, R, S, T, U, W, X, Y   ・  Output Port Settings (On/Off, Protocol, Bit Format, Baud Rate):  -  RS–232C and I/O DATA:  ON, NONE, 8 DATA BITS, 1 STOP BIT, ODD, 0.11  - RS–422:  ON, IEC61162, 8 DATA BITS, 1 STOP BIT, ODD, 4.8  - I/O DATA:  ON, NONE, 8 DATA BITS, 1 STOP BIT, ODD, 4.8  (continued on next page)
AE–1800 Instruction Manual User–made Settings 12. User Settings To Be Stored in Non–Volatile Memory (continued –2/2)   ・  Message Output (for printing live messages on–line)   - RECEIVING MSG:  ON, OFF   ・ *3Message Alarms On/Off  - Type A Message:  ON, OFF  -  Type B Message:  ON, OFF  -  Type D Message:  ON  -  Type L Message:  ON, OFF  *1: Can be controlled via RS–422 port with IEC 61162–1 proprietary command. Last setting is stored in memory. *2: Can be controlled via RS–422 port with IEC 61162–1 $CRNRM command. Last settings are stored in memory. Message types A, B, D and L cannot be rejected. *3: Type D message alarm is always set to ON; the user cannot change the status.
AE–1800 Instruction Manual List of Components To Be Shipped 13.  List of Components To Be Shipped  The following set of components is usually shipped by the manufacturer, either as standard or optionally. The same information is usually given in the shipping documents (INVOICE, PACKING LIST, etc. as requested by the user) to be attached to the shipment. If your equipment is purchased from one of MORCOM–authorized dealers, a different set of components may be delivered. Contact your dealer for details.   ●  Receiver Console (Cabinet), AE–1800: Standard  1 set ●  Active Antenna Assembly, ANT–2000M: Standard  1 set  ・ Preamplifier with *110m coax cable terminated in BNC plug  ・ Whip, 1.2m  ●  Receiver Mounting Bracket:  Standard  1 pc ●  Cabinet Clamping Knob, M8X15: Standard  2 pcs ●  Power Supply Cable:  Standard  1 set  3m, 2–conductor shielded, terminated in type 14–P3F plug  ● *2Plugs:  ・ CP111–4P (ALARM port):  Standard  1 pc  ・ CP111–8P (I/O DATA port):  Standard  1 pc  ・ HDEB–9S (RS–232C, RS–422 ports):  Standard  2 pcs  ●  Fuse (3A, 125V, 5.2X20 mm):  Standard  2 pcs  ● Reference Manual, *3UM–AE1800–1.0: Standard  1 copy   *1  OEM models are supplied with 1m RG58 /U coax cable terminated in a PL–259. *2: Equivalent substitutes may be supplied. *3: Edition number may change depending on delivery time.
AE–1800 Instruction Manual                                              MORCOM INTERNATIONAL, INC. 3656 Centerview Drive, Unit #1 Chantilly, VA 20151, U. S. A.    1st Edition, January., 2008 UM–AE1800–1.0 Printed in Japan

Navigation menu