Mosquito Magnet Defender Users Manual Liberty_Man_02

Defender mosquito-magnet-defender-manual

Defender to the manual aec129be-c938-4493-91d2-1bf3af3473c4

: Mosquito-Magnet Mosquito-Magnet-Defender-Users-Manual-557607 mosquito-magnet-defender-users-manual-557607 mosquito-magnet pdf

Open the PDF directly: View PDF .
Page Count: 9

MOSQUITO MAGNET

Defender

OPERATION MANUAL

OPERATION MANUAL

For Outdoor Use Only

US Patents: No. 6,145,243, No. 6,286,249

AU Patent No. 726575, NZ Patent No. 335035

®

MADE IN USA

PART NO. 1440-501 Rev. A

Your trap will

begin capturing

immediately, but

allow 4-6 weeks

to interrupt the

breeding cycle.

American Biophysics Corporation

2240 South County Trail

East Greenwich, RI 02818-1536

Place

First-Class

Postage

Here

PLEASE FOLD AND SEAL WITH TAPE ALONG OPEN END. DO NOT USE STAPLES

FOR YOUR SAFETY

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. If odor continues, immediately call your gas supplier.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors and liquids in the

vacinity of this or any other appliance.

WARNING: For Outdoor Use Only

MOSQUITO MAGNET

SAFETY INSTRUCTIONS

Model No.: DEFENDER

Serial No.:

Type of Gas: Propane

Manifold Pressure: 100-110 psi

Minimum Gas Supply Pressure: 11.0 in. WC

Input Rating: 650Btu/Hr.

Minimum Clearances: 20-24”

For Outdoor Use Only. If Stored Indoors, Detach and Leave Propane Cylinder Outdoors.

NOTICE: PLEASE READ THE ENTIRE MANUAL

BEFORE ASSEMBLING AND STARTING UP YOUR

MOSQUITO MAGNET DEFENDER.

TABLE OF CONTENTS

1. Safety…………………………..……...........................................2-4

2. Parts included……………………...........................................……5

4. Additional Components ……………….............................................6

5. Assembly instructions………………............................................7-9

6. Trap Placement………………………...........................................10

7. Start-Up Instructions……………….........................................…..10

8. Shut-Down Instructions………………...........................................11

9. Tank Changing Tips..............................................................................11

9. Maintenance.........................................................................................11

10. For Best Results...................................................................................12

11. Gas Reset Tool......................................................................................12

12. Quick-Clear Valve…………………..........................................…...13

13. Burying The Cord.................................................................................13

14. Troubleshooting…………………….....................................…......14

15. Warranty……………….....................................................................15

Humans exhale carbon dioxide (CO

2

), which has been scientifically

proven to be the natural compound that mosquitoes and other biting

insects use to navigate to people. The Mosquito Magnet mimics a

person’s breath by catalytically converting propane to carbon dioxide

(CO

2

). The Mosquito Magnet can be placed near the mosquito’s

resting and breeding spots, trapping the mosquitoes at their source

(see trap placement section). The female, egg-laying, biting mosquitoes

are drawn away from you and to the Mosquito Magnet, where they are vacuumed

into a net and dehydrate. Within 4-6 weeks, the reproductive cycles of your biting

insect population are interrupted. NO EGGS. NO INSECTS.

The Mosquito Magnet targets only biting insects, not beneficial

insects such as butterflies, bees and moths.

Congratulations on your Mosquito Magnet purchase!

Please read your owner’s manual completely before assembling and

operating your unit.

HOW THE MOSQUITO MAGNET WORKS

Defender

12

American Biophysics Corporation

2240 South County Trail

East Greenwich, RI 02818-1536

P: 401-884-3500 F: 401-884-6688

www.mosquitomagnet.com

email: info@mosquitomagnet.com

Please contact American Biophysics

Corporation if you experience any prob-

lems with your Mosquito Magnet:

1-877-699-8727

The LP-Gas cylinder supply system must be arranged for vapor withdrawal and the cylinder must include a

collar to protect the cylinder valve.

The LP-Gas cylinder used shall be constructed and marked in accordance with the specifications for

LP-Gas cylinders of the U.S. Department of Transportation (DOT).

The Mosquito Magnet shall be used outdoors only in a well ventilated space and shall not be used in a

building, garage, or any other enclosed area.

The LP-Gas cylinder must be disconnected and removed from the appliance, if the appliance is stored

indoors.

LP-Gas cylinders must be stored outdoors in a well ventilated area out of the reach of children.

Disconnected cylinders must have threaded valve plugs tightly installed and must not be stored in a

building, garage, or any other enclosed area.

The pressure regulator and hose assembly supplied with this appliance must be used for connection

to the LP-Gas cylinder. Replacement pressure regulators and hose assemblies must be specified by

the manufacturer.

Avoid improper use of extension cords. Keep connections away from moisture and avoid damage

to the cord.

If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly

qualified person in order to avoid hazard.

WARNING- an electric shock hazard may exist if water from a garden hose is directed at the

Mosquito Magnet.

WARNING: Improper installation, adjustment, alteration, service or maintenance

can cause injury or property damage. Read the installation, operating and

maintenance instructions thoroughly before installing or servicing this equipment.

CAUTION: The gas pressure regulator provided with this appliance must be used. This regulator is

set for an outlet pressure of 11.0 in. Water Column.

The gas supply must be turned off at the LP-Gas supply cylinder when this appliance is not in use.

The installation must conform with local codes or, in the absence of local codes, with the National

Fuel Gas Code, ANSI Z223.1-1998 for US and with the CAN1-B149 for Canada.

Adequate clearances of 20-24 inches around air openings into the combustion chamber, clearances

from combustible material, provisions for accessibility and for combustion and ventilating air supply.

The minimum inlet gas supply pressure is 11”WC from regulator.

To test for a gas leak, place soapy water around the regulator. If bubbles appear, there is a gas leak.

Route the power cord in the safest possible manner to avoid personal injury.

Installation and repair should be done by a qualified service person. The heater should be inspected

before use and at least annually by a qualified service person. More frequent cleaning may be re-

quired as necessary. It is imperative that the control compartment, burners, and circulating air pas-

sageways of the heater be kept clean.

Keeping the Mosquito Magnet area clear and free from combustible materials, gasoline, and other

flammable vapors and liquids. The appliance is not to be used in locations where flammable vapor or

explosive dust is likely to exist.

Do not obstruct the flow of combustion and ventilation air.

Keeping the ventilation openings of the cylinder enclosure free and clear from debris.

Clean the Mosquito Magnet with a water damp cloth, if necessary.

A maximum of a 20 lb. LP-Gas cylinder shall be used.

The hose assembly must be replaced prior to the appliance being put into operation if there is evi-

dence of excessive abrasion or wear, or if the hose is damaged. The instructions shall state that the

replacement hose assembly shall be that specified by the manufacturer.

The Mosquito Magnet is equipped with a hot surface ignition device. Failure to follow starting proce-

dure will result in the trap not starting.

Children and adults should be alerted to the hazards of high surface temperatures

and should stay away to avoid burns or clothing ignition.

Young children should be carefully supervised when they are in the area of the heater.

Keep out of reach of children.

Clothing or other flammable materials should not be hung from

the heater, or placed on or near the heater.

34

The LP-Gas cylinder must be provided with a shutoff valve terminating in an LP-Gas supply cylinder valve

outlet specified for Connection No. 510 in the Standard for Compressed Gas Cylinder Valve Outlet and Inlet

Connections, ANSI/CGA-V-1-1977.

PARTS INCLUDED

(1) Base Support

(1) Support

Leg

(1) Self-contained

Defender

powerhead

(1) Net

(already

installed)

(1) Octenol Cartridge

(Added Attractant)

(1) Adaptor

ADDITIONAL COMPONENTS

(1) Support

Pole

(1) L-Shaped Adaptor (10) Metal Cord Burying Clips

(1) Reset Tool

(1) Instruction Manual

IMPORTANT NOTICE

Per Federal Regulations, a CO2

Cartridge has not been included

with your purchase. Please visit

www. mosquitomagnet.com to

purchase or visit your local

Mosquito Magnet

dealer.

56

ASSEMBLY INSTRUCTIONS

1. Your trap will begin capturing

immediately, but allow 4-6

weeks to interrupt the breed-

ing cycle.

2. DO NOT MOVE MOSQUITO

MAGNET WITH TANK AT-

TACHED. DISCONNECT TANK

FROM REGULATOR BEFORE

RELOCATING TRAP TO AVOID

DAMAGE TO REGULATOR OR

TRAP.

3. Should you experience an

interruption of power, be sure

to restart trap.

4. Trap can be left running in

the rain.

IMPORTANT NOTES:

2

Place base upside down on

a flat surface, slide U-

shaped support legs into

slots on base until they lock

in place.

ASSEMBLY INSTRUCTIONS

1

Turn base and leg assembly

right-side-up and place

support pole into cavity on

base.

3

Place Defender power head

onto pole. Press down firmly

with two hands to secure.

4

Completed assembly should

have the front of power

head in the same direction

as base U-shaped legs.

5

Peel cover from attractant

cartridge. Using a coin,

unscrew cover from attrac-

tant compartment inside of

CO

2

tube.

6

Slide attractant cartridge

into compartment. Recap

and secure tightly.

7

Place propane tank onto

base into the molded cradle

supplied.

8

Making sure propane tank

is fully closed, attach pro-

pane regulator hose to

propane tank. Secure tightly

by hand. Do not use tools.

78

It is recommended that you read the entire manual before starting the Mosquito Magnet Defender

ASSEMBLY/STARTING INSTRUCTIONS TRAP PLACEMENT

1

2

3

4

Determine the direction of the prevailing wind.

Stand in the center of the area you are trying to protect and look toward the prevailing wind. Proper

placement of the Mosquito Magnet will be 30-40 feet in front of you, within 5-6 feet of ground cover

(i.e., bushes, flowerbeds, treeline, marshbed, etc.)

It is recommended that the trap be placed in the shade.

Do not place trap directly above water source (sprinklers, hose, etc.).

Make sure unit is not directly up against a blockade such as a building or fence.

Trap must be placed on level ground to avoid tipping or uneven propane distribution.

For more information, refer to trap placement section of our website at www.mosquitomagnet.com.

5

6

7

9

Plug power connector into

the Defender unit power

slot located on the back of

the power head.

Plug adaptor into properly

grounded electrical outlet.

This adaptor is not intended

to be mounted. For UL Listed

trap use 120 Vac adaptor.

For CE marked trap use 230

Vac adaptor.

Turn propane on by slowly

turning counterclockwise.

Take care

not

to turn too

quickly to avoid engage-

ment of safety check valve

in regulator.

11

10

CONTINUE

TO STARTING

INSTRUCTIONS.

910

STARTING INSTRUCTIONS

1

2

3

4

5

6

7

Connect regulator to propane tank.

Plug power connector into the trap.

Plug AC adapter into electrical socket. To avoid the risk of electrical shock, connect only to properly

grounded outlets. Adaptor unit is not intended to be mounted.

Slowly

turn propane tank on (turn valve counter clockwise).

Turn rocker switch to “on” position.

The red light on the switch will flash for up to 20 minutes (warm up phase).

Once the light stops flashing and is solid the Mosquito Magnet is fully operational.

If your Mosquito Magnet fails to start, it may be the result of poor gas flow from the propane tank through the regulator to the trap.

The attached tool has been designed to reset the internal mechanisms of the propane regulator and release any back pressure

from your tank. Please follow these steps:

Shut down your Mosquito Magnet.

Completely close the propane tank valve by turning to the “Off” position. (turn valve clockwise)

Disconnect the regulator from the propane tank valve.

Screw the threaded end of the reset tool into the propane tank valve until it is fully engaged.

You may hear a small “hiss” sound. This is the pressure being released from the propane tank.

Note: the threads in the tank valve are left handed threads. (turn valve counter clockwise)

Screw the regulator connector to the opposite end of the reset tool until fully engaged.

Note: hold the reset tool to

prevent it from backing out of the tank.

The regulator and propane tank are now reset. Disconnect the reset tool from the

regulator connector and the propane tank.

Re-attach regulator connector to the propane tank valve.

Slowly turn the propane tank valve on .

Restart your trap.

SHUT DOWN INSTRUCTIONS

To shut down the Defender simply close the valve on the propane tank and switch to “Off” position.

DO NOT UNPLUG UNIT. MOSQUITO MAGNET DEFENDER MUST REMAIN PLUGGED IN FOR 5 MINUTES AFTER

SHUT DOWN OR UNTIL FAN STOPS TO AVOID HEAT DAMAGE.

Any open octenol or other added attractant packages should be removed and discarded. The net should also be

discarded prior to storing the Mosquito Magnet Defender.

STORAGE: Mosquito Magnet Defender should be stored indoors in the off-season. Cover unit with trap cover

(available at www.mosquitomagnet.com) or with a tarp and secure tightly at the bottom to keep out dust,

spider webs and other debris.

MAINTENANCE

FOR BEST RESULTS

Your trap will begin capturing immediately, but allow 4-6 weeks to interrupt the breeding cycles.

Should you experience an interruption of power, be sure to restart the trap.

Clear door must be closed tightly to maximize catch.

Never spray insecticide in or around trap.

DO NOT MOVE TRAP WITH TANK ATTACHED! TANK MUST BE DISCON-

NECTED FROM REGULATOR BEFORE TRAP IS RELOCATED TO AVOID

DAMAGE TO REGULATOR AND/OR TRAP.

BE ADVISED, DAMAGE

CAUSED FROM FAILURE TO COMPLY WITH THIS INSTRUCTION IS NOT

COVERED UNDER WARRANTY.

Trap can be left running in the rain.

If using lime or lawn regenerative compounds, be sure to shut down the

Mosquito Magnet first to prevent dust or fine mist from being drawn into trap

and clogging net.

A standard, outdoor rated extension cord may be used to increase your trap area.

Octenol cartridge does not disintegrate. Smell will dissipate over time.

1

2

3

4

5

6

7

8

9

Propane tank should be refilled every 21 days.

Empty or replace net every 21 days.

See added attractant packaging for maintenance/ replacement instructions.

Accessories can be ordered at www.mosquitomagnet.com

Store Octenol in a cool, dry place.

Clean net periodically for tree pollen or debris.

In the event the side screen becomes clogged, remove and clean gently with toothbrush and cold

water.

Periodically wipe down the outside of the Mosquito Magnet with a clean water damp cloth.

1

2

3

4

5

6

7

TANK CHANGING TIPS

When attaching the regulator handle to a tank after a tank change, be sure to fully tighten the regulator

handle onto the tank. No need to use tools, but do turn the handle as far as possible by hand. When this is

done, loosen the handle 1/4 turn, then re-tighten the handle. Frequently this action will result in additional

turns beyond the 1/4 turn. The purpose for this is to fully engage the regulator onto the tank. If the regula-

tor is not fully engaged, the flow of gas may be restricted to the point where the trap will show a gas empty

code. If this occurs, press the off button, close the tank valve, and remove the regulator from the tank. Re-

attach the regulator and try again.

8

11 12

GAS RESET TOOL INSTRUCTIONS

1

2

3

4

NOTE: It is recommended that you use the Quick-Clear valve before seasonal storage to avoid build-up of

contaminants during off-season.

Technical Support: 1-877-699-8727

Gas Reset Tool

Extinguish all smoking materials prior

to use of Gas Reset Tool.

5

6

7

8

9

QUICK-CLEAR VALVE TROUBLESHOOTING GUIDE

1) Is Propane tank empty?

2) If Propane tank is new, has it

been purged?

3) There could be a loose

connection.

4) If tank has been opened too

quickly, security check valve

may have triggered.

1) Issues 1and 3 may apply.

2) Fuel line may be blocked by

propane contaminates.

3) Regulator is not fully engaged.

If not getting bitten

1) Insects may not be out yet.

If getting bitten

2) Trap placement issue.

3) Biting insect reproductive

cycles have not yet been broken.

4) CounterFlow may be disrupted.

5) Added attractant may be

incompatible with species of

mosquito.

Unit won’t start

Unit won’t stay running

Low or No Catch

1) Weigh tank and check against “empty” weight

written on tank.

2) Bring tank to filling location. Air may be in fuel line.

Ask for tank to be purged. *Hint-If you have an-

other propane powered device operating on a

standard, 20lb propane tank, try hooking that tank

up to the Mosquito Magnet to verify that your issue

is with your tank.

3) Verify all electrical connections. Make sure

regulator is fully engaged, and propane tank valve

is fully open.

4) Refer to Reset Tool Instructions on page 12.

1) Go through above steps 1 & 3.

2) See Quick-Clear valve instructions.

3) See Tank Changing Tips on page 11.

1) Verify temperature is consistently above 50°F (10°C).

2) Follow steps in the “Trap Placement” section of

your owner’s manual or go to

www.mosquitomagnet.com “Placement” section.

3) Keep trap in constant operation 24 hours/day, 7

days/week for 4-6 weeks to interrupt

the breeding cycle.

4) Conduct a “tissue test” by holding a facial tissue

up to horn to check for airflow.

5) Call your local mosquito control department to find

out if Asian Tiger is your primary species of mos

quito.

Asian Tiger mosquitoes are not attracted to

Octenol.

Remove Octenol cartridge from your unit,

and wipe Octenol compartment with alcohol wipe

to eliminate scent.

PROBLEM POSSIBLE CAUSES SOLUTIONS

All of us at American Biophysics want you to get complete satisfaction from your

Defender. Should you have any problems you cannot resolve, simply call one of

our trained Technical Service Representatives at:

Use of protective eyewear is recommended

Important: Extinguish all smoking materials prior to use of Quick-Clear valve.

13 14

Recommended for use at first tank change, and every second tank change thereafter. Also recommended for

use before seasonal storage to avoid build up of contaminant’s during off-season.

The Quick-Clear valve is used to clear out propane contaminants in the fuel line, which may block the flow of

propane from the tank to your Mosquito Magnet. The Quick-Clear valve is a gold, threaded knob located on the

back of your trap. It should be used with the black and gold, L-shaped adapter included in the box with your

Mosquito Magnet, and a 12 gram threaded CO

2

cylinder available on our website at www.mosquitomagnet.com

or your local Mosquito Magnet Dealer.

1

2

3

4

5

6

7

8

BURYING THE POWER CORD

Use straight-

edge shovel or

garden spade

and dig a trench

about 3-4 inches

deep from power

source to trap.

Place cord into

trench carefully

stretching as you

go to remove any

twists in cord.

Use cedar

shingle or folded

cardboard to

place cord into

bottom of trench.

Recover the

trench with

removed soil.

Use the Cord Burying Clips supplied. Place clips approximately 5’ apart, tap into ground with a hammer making sure not to

damage power cord. Make sure unit is unplugged and in proper position. For alternate placement follow steps illustrated below.

1-877-699-8727. We will help you get up and running.

Important: Extinguish all smoking materials prior to use of Quick-Clear Valve.

Do not stand directly behind cylinder during operation.

Shut down your Mosquito Magnet. Let fan run until it stops. (about 5 mins.)

Close the propane tank valve by turning to the “Off” position. (turn the tank valve clockwise)

Remove the protective cap from Quick-Clear valve on your trap.

Hand-screw gold end of L-shaped adapter on to Quick-Clear valve, until tight.

Hand-screw the CO2 cylinder into black end of L-shaped adapter clockwise until hand tight.

Unscrew CO2 cylinder 1/4 turn only in counter-clockwise direction. The flow of CO2 will begin, lasting approxi-

mately 3 minutes. Be sure to allow CO2 to run out completely. (hissing will stop when cylinder is empty. Note:

CO2 cylinder will be cold to the touch)

Continue unscrewing the CO2 cylinder to remove. Discard empty CO2 cylinder after use, it is not reusable or

re-fillable. (Use caution when removing CO2 cylinder, as some residual CO2 may come out at this time.)

Remove L-shaped adapter by unscrewing gold end clockwise. (Remember to KEEP the black and gold adapter

for future use!)

Replace Quick-Clear valve protective cap, and proceed with normal start up of your Mosquito Magnet.

If use of Quick-Clear valve feature does not resolve starting trouble, contact Tech Support 877-699-8727.

Remember to KEEP the black and gold adapter for future use

9

1. How did you find out about the Mosquito Magnet (check all that apply)?

Radio Ad Direct Mail TV Ad

Friend/Family Website Magazine Ad

Newspaper Ad News Article (newspaper, magazine, TV, etc.)

Frontgate In-Store Display Other

2. In your household who decided to purchase the Mosquito Magnet?

Male Female Both

3. What is your marital status?

Married Single

4. Are there any children in your household?

Yes No

5. What are the two most important reasons influencing this purchase?

Protection from disease

Science/technology behind product

Recommendation of friend/family member

Recommendation of salesperson

Reputation of quality

Comfort

Received as gift

Other

6. What is your age?

25-35 36-45 46-55 56-70 70+

7. What is your level of education?

High School Diploma College Degree Graduate Degree Doctoral Degree Technical/Professional

8. Which best describes the size of your yard?

1/4-1/2 acre 1/2-3/4 acre 3/4-1 acre 1-2 acres

9. What is your annual income?

$25,000-40,000 $40,000-60,000 $60,000-90,000 Over $90,000

10. What other brands of insect abatement have you tried?

Zappers Sprays Pesticides Other CO

2

Traps Name

11. Would you consider giving a testimonial once you are thoroughly convinced of the effectiveness of the Mosquito Magnet?

Yes No

12. Would you recommend the Mosquito Magnet to a friend?

Yes No

13. Were the assembly directions and operation instructions explained clearly and simply?

Yes No

14. Did you require customer service?

Yes No

LIMITED WARRANTY

DETACH HERE BEFORE MAILING

DETACH HERE BEFORE MAILING

First Name

Last Name

Address

City

State/Province Zip Code

Country

Phone Number

Email Address

Consumer Confidentiality

All of the information that has been gathered on this reply

card is solely for the internal sales and marketing efforts of

American Biophysics Corporation. None of the information

that you may have provided will be sold, rented or leased

to any other company, organization or agency for any

purpose whatsoever. None of this information will be

posted on our company website or any other vehicle that

can be obtained by the public domain.

If you wish to make additional comments or testimonials

about our product, please address them separately and

send them to our Marketing Department at the address

listed inside the manual.

PRODUCT REGISTRATION

Type of unit:

Serial Number:

Date of purchase:

Place of purchase:

NECESSARY INFORMATION

IN ORDER TO PROPERLY

REGISTER YOUR PRODUCT

WITH AMERICAN BIOPHYSICS

CORPORATION, THE FOLLOW-

ING INFORMATION IS

REQUIRED.

15

*

Mail completed form today or register on-line at www.mosquitomagnet.com

This warranty, (1) year from the purchase of the unit, is extended only to the original purchaser/user of products.

American Biophysics Corp. warrants its products to be free from defects in materials and workmanship for the warranty

period by the original purchaser/user.

For warranty service, please contact American Biophysics Technical Center (877-699-8727). Please indicate the nature

of the defect.

After calling for warranty service, please contact the retailer where you bought your unit to determine if it is covered by

any exchange policy.

If American Biophysics Corp. determines there may be a defect, American Biophysics Corp. will issue a return authoriza-

tion (RMA) number.

The defective unit or parts must be returned for warranty inspection using the RMA number, when applicable, as identi-

fication within (30) days of return authorization date. DO NOT return products to our factory without our prior consent, as

they, as well as C.O.D. shipments will be refused. American Biophysics Corp., at its option, shall replace the unit, replace

the defective part(s) and return such unit to you. American Biophysics Corp.’s sole obligation and your exclusive remedy

under this warranty shall be limited to such replacement.

LIMITATIONS AND EXCLUSIONS: The warranty shall not apply to problems arising from normal wear, or failure to adhere

to the enclosed instructions. In addition, the foregoing warranty shall not apply to serial numbered products if the serial

number has been removed or defaced; products subject to negligence, accident, improper operation, maintenance or

storage; products damaged by circumstances beyond American Biophysics Corp.’s control; or products modified (includ-

ing, but not limited to modifications through the use of unauthorized parts or attachments) or repaired by anyone other

than American Biophysics Corp. or its designee.

THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUD-

ING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PUR-

POSE. IT SHALL NOT EXTEND BEYOND THE DURATION OF THE EXPRESS WARRANTY PROVIDED HEREIN, AND THE

REMEDY FOR VIOLATIONS OF ANY WARRANTY SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE DEFECTIVE

PRODUCT PURSUANT TO THE TERMS CONTAINED HEREIN. AMERICAN BIOPHYSICS CORP. SHALL NOT BE LIABLE FOR

ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER.

This warranty gives you specific legal rights and you may also have other legal rights which may vary based on location.