Mossloo MSLW178Q Glisten 4000 mAh Light Up Wireless Powerbank User Manual gai2

Shenzhen Mossloo Industrial Co.,Ltd Glisten 4000 mAh Light Up Wireless Powerbank gai2

Contents

User Manual

MADE IN CHINA
FCC WARNING STATEMENT
Glisten 4000 mAh Light Up
Wireless Powerbank
Instruction Manual
1 x 4000 mAh wireless Power Bank
1 x 2-in-1 charging cable (see above diagram)
1 x Instruction Manual
4000 mAh/3.7V/14.8WH
USB Input: DC 5V/2A
USB Output: DC 5V/2A
Wireless Output: 5V/1A
ON/OFF Button: Press once to view the
remaining power capacity.
Will illuminate whenever the power bank
charges or discharges.
Charge the power bank fully before initial use.
The unit’s full performance is achieved only
after 2 or 3 completed charge and discharge
cycles.
To reduce the risk of injury, close
supervision is necessary when the product
is used near children.
Do not expose the device to moisture.
Do not use the device in excess of its
output rating. Overload outputs above
Do not use the device if damaged or
explosion or risk of injury.
Do not disassemble the device. Take it to
or repair is required. Incorrect reassembly
or temperatures above 212ºF may cause
explosion.
repair person using only identical
replacement parts.
Do not overcharge Phone. Unit may get hot
with excessive use. Remove Phone when it
is fully charged. Never charge for more than
7 hours at a time.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
•
•
•
•
•
•
What’s included:
Features:
LED Indicators:
Light Panel: WARNING–When using this product, basic
precautions should always be followed,
including the following:
Read all the instructions before using the
product.
1.
SAFETY PRECAUTIONS:
1.
2.
3.
4.
5.
Wireless Charging Pad
Micro USB Input
USB Output
LED Indicator
ON/OFF Button
Charging the power bank:
Charge the power bank fully before usage.
Using 2-in-1 charging cable, insert the USB
USB port of a computer, insert the 2-in-1
tip (the side with pins upwards) into power
bank micro input. Then charge begins.
BLUE, and will stop when once fully
charged.
Charging mobile phones and other
electronic devices:
Connect the 2-in-1 cable to your mobile
phone/device. If Android device, the tip with
pins upwards; If iOS device, the tip without
pins upwards. Connect the other end to the
power bank. Device will begin to charge
automatically.
Remove the USB cable from your mobile
device when it is fully charged.
Charging Mobile phones and other
electronic devices with wireless output.
Press and hold the ON/OFF button,
LED indicator will show Green once the
powerbank is in wireless charging standby
mode.
Place wireless charging enable device on
Wireless Charging Pad. The device will
begin to charge, LED indicator will turn
RED when charging.
Note: In order to charge devices, use only
the accessory cable or the cable included
with your own device by the manufacturer.
1.
a.
b.
c.
2.
a.
b.
3.
a.
b.
*
Instructions:
WIRELESS CHARGING ENABLED
DEVICES:
iPhone 8/8Plus/X, Samsung Galaxy S8/
S8+/S7/S7 Edge/S6/S6 Edge, Nokia Lumia
1020/920/928, HTC 8X, HTC Droid DNA, HTC
Rzound, HTC Incredibly 4G LTE, Moto Droid
Turbo, Motorola Moto 360 Smart Watch, Moto
Droid Maxx, Droid Mini, Google Nexus 6/4/5/7
(2013), LG D1L, LG LTE2, LG G2 (Verizon),
Blackberry Z30 (Verizon)
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) this device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation. Any changes or modifications not
expressly approved by the party responsible
for compliance could void the user's authority
to operate the equipment.
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user
is encouraged to try to correct the interference
by one or more of the following
measures:
‐Reorient or relocate the receiving antenna.
‐Increase the separation between the
equipment and receiver.
‐Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
‐Consult the dealer or an experienced radio/
TV technician for help.

Navigation menu