Motorola Mobility T5ZX1 Mobile Cellular Transceiver User Manual Exhibit 8c

Motorola Mobility LLC Mobile Cellular Transceiver Exhibit 8c

Contents

Motorola installation guide includes rf exposure responses to 11299

APPLICANT: MOTOROLA, INC. FCC ID: IHDT5ZX1EXHIBIT 8cA draft copy of the installation manual follows.Note: RF exposure information is provided on page 33.
Cellular Mobile and AttacheAccessoryInstallation Manual
Attache Accessory ...............................................................1Introduction ........................................................................1Attache Models ..................................................................2Attache Assembly ..............................................................3Assembly Procedure .....................................................3Secure the Unit .............................................................9Disassembly ..................................................................9Carry Phone Accessory.....................................................11Introduction ......................................................................11Carry Phone Models ........................................................12Carry Phone Assembly ....................................................13Assembly Procedure ...................................................13Secure the Unit ...........................................................18Disassembly ................................................................19Basic Operation..................................................................20Power the Unit .................................................................20Turn Off the Unit ..............................................................20Release the Handset .......................................................21Antenna Position..............................................................21Optional Features...............................................................22Digital Hands-Free Operation ..........................................22Battery Option..................................................................23Mobile Installation ..............................................................27Planning and Installation..................................................27Transceiver Location....................................................27Standard Transceiver Mounting Bracket Installation ...27Handset Location ........................................................28Control Unit Mounting Cup Installation .......................30Adjustable Angle Mounting Bracket Installation (optional) ......................30Antenna Location ........................................................32Antenna Installation.....................................................33Hands-Free Microphone Installation ...........................33Optional External Speaker Installation ........................34Control/Power Cable Routing ......................................35Control/Power Cable Installation .................................36Performance Checks........................................................39Checking Performance ................................................39Checking Auxiliary Alert Feature.................................40Before Calling for Service .................................................42General Safety Information ...............................................44Rules, Regulations, and Precautions ...............................50, and Motorola are trademarks of Motorola, Inc.Installation ManualTOC
Attache AccessoryNOTE Not all Motorola models are available forpurchase as Attaches. Check with your cellular dealerfor information regarding the purchase of the Attacheaccessory to convert your mobile into an Attache.IntroductionThis section of your manual describes the assemblyand installation of the Motorola Attache. The MotorolaAttache is a lightweight, three-watt unit that ispowered by your vehicle’s electrical system throughthe cigarette lighter socket. This phone is completelyself-contained, and may be moved easily betweenyour personal car(s), a company truck or car, or arental car because it requires no complex wiringinstallation within the vehicle. The unit is installed inthe vehicle by simply securing it to a spare seat with alap belt and plugging it into the vehicle’s cigarettelighter socket. For further information about thefeatures and capabilities of your cellular telephone,see the accompanying user manual.Installation Manual1
Figure 1Attache ModelsTwo Attache models are offered. The standardversion is powered by your vehicle’s electrical systemand does not come equipped with a battery. Thepower connector assembly contains connectors for anoptional battery and an external hands-freemicrophone, if so desired.The deluxe version comes complete with a battery, anAC charger, and an integrated hands-free microphonecontained in the connector assembly. An external full-duplex hands-free microphone can be purchasedseparately.The hands-free feature allows you to place or answercalls without removing your hands from the steeringwheel (except to enter the number to be called). SeeInstallation Manual2BagHandsetBatteryBatteryAdapterHands-FreeMicrophone(optional)AntennaBatteryChargerTransceiverPower Connector withCigarette Adapter
Digital Hands-Free Operation in the User Manual formore information about hands-free calling.Attache AssemblyThe items included with your Motorola Attache areshown in Figure 1. The following procedure will guideyou through the assembly of your Attache.Assembly ProcedureStep 1 Remove the transceiver from its Attachecompartment.Step 2 Carefully connect the 25-pin connector of thepower connector assembly to the front of thetransceiver and tighten the two thumbscrewsas shown in Figure 2. Figure 2Installation Manual3
Step 3 Locate the antenna and screw it tightly ontothe connector as shown in Figure 3.Figure 3If your Attache is equipped with a battery, proceed tostep 5.Step 4 Carefully place the transceiver, antenna, andconnector assembly into the transceiverpocket as shown in Figure 4a, and zip thepocket closed, leaving the antenna outside ofthe pocket as shown in Figure 4b.Be sure to connect the cigarette lighter plug tothe cigarette lighter socket on your vehicledashboard when you are ready to use yourphone.Installation Manual4
Figure 4aFigure 4bInstallation Manual5
Steps 5 and 6 should be followed if your Attache isequipped with a battery.Step 5 Locate the battery adapter cable and snap thebattery connector clip onto the battery asshown in Figure 5a. Attach the other end tothe battery connector assembly as shown inFigure 5b.Figure 5aFigure 5bInstallation Manual6
Step 6 Carefully place the transceiver/batteryassembly into the transceiver pocket as shownin Figure 6, and zip closed.Figure 6Step 7 Plug the handset modular connector into thejack located on the side of the transceiver asshown in Figure 7, and place the handset intothe hang-up cup.Figure 7Installation Manual7
Step 8 Finally, use your pocket system for businessplanning tools such as calendars, notepads,business cards, etc. as shown in Figure 8. NOTE These items are purchased separately.NOTE Be sure to charge the battery for atleast 10 hours, or overnight, using the ACcharger before attempting to use the cellulartelephone.Figure 8Installation Manual8
Secure the UnitTo secure the unit in your vehicle, run a standard lapbelt through the loop located on the outside of thecarry case as shown in Figure 9.Figure 9DisassemblyIf you wish to remove the handset and transceiverfrom the Attache accessory for servicing, or to placethem in a vehicle equipped with a permanent mobileinstallation, use the following procedure.Step 1 Turn the unit off by pressing ∏ on the handset.Step 2 Unplug the handset from the modularconnector jack on the side of the transceiverand remove it from the hang-up cup.Step 3 Unzip the transceiver compartment andcarefully lift the transceiver/connectorassembly out of the pocket.Step 4 Unscrew and remove the antenna.Installation Manual9
Step 5 Unscrew the two thumbscrews on the front ofthe power connector and remove the powerconnector assembly from the transceiver bygently pulling it away from the transceiver frontplate.Step 6 Return the antenna and power connectorassembly into the carrying case for safekeeping.Reverse the above procedure to re-assemble. Seepage 20 for Basic Operation.Installation Manual10
Carry Phone AccessoryNOTE Not all Motorola models are available forpurchase as carry phones. Check with your cellulardealer for information regarding the purchase of thecarry phone accessory to convert your mobile into acarry phone.Introduction This section of your manual describes the assemblyand installation of the Motorola cellular carry phone.The Motorola cellular carry phone is a lightweight,three-watt unit that is powered by your vehicle’selectrical system through the cigarette lighter socket.This phone is completely self-contained, and may bemoved easily between your personal car(s), acompany truck or car, or a rental car because itrequires no complex wiring installation within thevehicle. The unit is installed in the vehicle by simplysecuring it to a spare seat with a lap belt and pluggingit into the vehicle’s cigarette lighter socket. For furtherinformation about the features and capabilities of yourcellular telephone, see the accompanying usermanual.Installation Manual11
Figure 10Carry Phone ModelsTwo carry phone models are offered. The standardversion is powered by your vehicle’s electrical systemand does not come equipped with a battery. Thepower connector assembly contains connectors for anoptional battery and an external hands-freemicrophone, if so desired.The deluxe version comes complete with a battery, anAC charger, and an integrated hands-free microphonecontained in the connector assembly. An externalfull-duplex hands-free microphone can be purchasedseparately.The hands-free feature allows you to place or answercalls without removing your hands from the steeringwheel (except to enter the number to be called). SeeDigital Hands-Free Operation on page 22 for moreinformation about hands-free calling.Installation Manual12BagHandsetBattery BatteryAdapterHands-FreeMicrophone(optional)AntennaBatteryChargerTransceiverSleevePower Connector with Cigarette Adapter
Carry Phone Assembly The items included with your Motorola cellular carryphone are shown in Figure 10. The following procedurewill guide you through the assembly of your carry phone.Assembly ProcedureStep 1 Remove all components from the bag.Step 2 Carefully connect the 25-pin connector of thepower connector assembly to the front of thetransceiver and tighten the two thumbscrewsas shown in Figure 11.Figure 11Step 3 Locate the antenna and screw it tightly ontothe connector as shown in Figure 12.Figure 12Installation Manual13
Step 4 Take the vinyl sleeve and slide the transceiverassembly into the sleeve, wrapping the Velcrotab over the power connector. Be sure thetelephone jack located on the side of thetransceiver lines up with the opening in thesleeve. See Figure 13.Figure 13Step 5 Place the handset in the hang-up cup andplug the handset modular connector into thejack located on the side of the transceiver.See Figure 14.Figure 14Installation Manual14
Step 6 Place the transceiver assembly into the bagallowing enough room for clearance of thehandset coil cord. See Figures 15a and 15b.Note that the antenna folds conveniently downinto the bag to prevent possible damage.NOTE Be sure to connect the cigarette lighterplug to the cigarette lighter socket on yourvehicle dashboard when you are ready to useyour phone.Figure 15aFigure 15bSteps 7 and 8 should be followed if your carry phoneis equipped with a battery.Installation Manual15
Step 7 Locate the battery adapter cable and attachthe modular end to the battery connectorassembly as shown below.Figure 16Feed the cable through the opening to the batterycompartment in the lower corner of the bag.Place the battery into the battery compartmentand snap the battery connector clip onto thebattery as shown in Figure 17.Figure 17Installation Manual16
Step 8 Zip the battery compartment closed. SeeFigure 18.Figure 18Step 9 The battery should now be charged for at least10 hours or overnight using the AC chargerbefore attempting to use the cellulartelephone.Please note that there is an opening in thelower left corner of the bag to allow forconnection of an external antenna. Thetransceiver unit can positioned in eitherdirection when placed in the bag. See Figures19a and 19b.Figure 19aInstallation Manual17
Figure 19bSecure the UnitTo secure the unit in your vehicle, run a standard lapbelt through the loop located on the outside of thecarry case as shown in Figure 20.Figure 20Installation Manual18
DisassemblyIf you wish to remove the handset and transceiverfrom the carry phone accessory for servicing, or toplace them in a vehicle equipped with a permanentmobile installation, use the following procedure.Step 1 Turn the unit off by pressing ∏ on thehandset.Step 2 Unplug the handset from the modularconnector jack on the side of the transceiverand remove it from the hang-up cup.Step 3 Lift the transceiver assembly out of the carrybag using the loop handle. Unwrap the Velcrotab and slide the transceiver out of the Velcrosleeve.Step 4 Unscrew and remove the antenna.Step 5 Unscrew the two thumbscrews on the front ofthe power connector and remove the powerconnector assembly from the transceiver bygently pulling it away from the transceiver frontplate.Step 6 Return the antenna and power connectorassembly into the carrying case for safekeeping.Reverse the above procedure to re-assemble.Installation Manual19
Basic Operation Power the Unit This unit is designed to operate in two differentmodes. The first operating mode is standard mode,and the second is battery saving mode. If yourAttache/Carry phone is not equipped with a battery, itwill always operate in the standard mode.Standard Mode When you plug your unit into the vehicle cigarettelighter socket and press ∏on the handset, the unitwill sense the voltage present at the cigarette lightersocket and automatically behave exactly as it would ina standard mobile installation. The handsetbacklighting will remain lit, and the handset displaywill stay ‘on’ as long as the telephone remains ‘on’.Battery Saving Mode When you press ∏on the handset, and thecigarette lighter plug is not plugged in (or there is novoltage present at the cigarette lighter socket) yourAttache/Carry phone will automatically shut off thehandset backlighting and blank the display after sixseconds. Pressing any key will turn the display andbacklighting back on for another six seconds.Turn Off the UnitYour Attache/Carry phone should always be turned offusing ∏on the handset.NOTE If the handset is unplugged from thetransceiver prior to turning off the unit with thehandset ∏,the unit will continue to drain its (or yourInstallation Manual20
vehicle’s) battery. It is very important to turn off theunit using ∏on the handset.Release the Handset Lift up and remove the handset, as shown in Figure 21.Figure 21Antenna Position If your Attache/Carry phone is equipped with a foldingantenna, the antenna may be folded downward forconvenient storage when the Attache/Carry phone isnot in use. However, for best performance whenusing the Attache/Carry phone, you should alwaysplace the antenna in the full upright position. Also,when using the Attache/Carry phone, remember tokeep the cigarette lighter cord, handset coil cord, andoptional hands-free microphone cord as far away fromthe antenna as possible.To Hang UpTargetHang-Up CupEngage Notch in Topof Handset AgainstTarget Button.Pivot Unitand Remove.Pivot UnitUntilLatched.123Installation Manual21
Optional FeaturesDigital Hands-Free Operation Your Attache/Carry phone may be equipped with ahands-free wireless microphone integrated into theconnector attached to the transceiver. This is a safetyfeature which offers the convenience of hands-freeconversation without the use of an externalmicrophone.For optimum hands-free sound quality while using theintegrated microphone, Enhanced SimplexHands-Free operation should be enabled through themenu. See page 15 in the User Manual for furtherdetails.For enhanced hands-free sound quality, an externalmicrophone can be purchased as an accessory and istypically positioned on your sun visor.Full Duplex Hands-Free provides improved audioquality relative to Enhanced Simplex Hands-Free andmakes it easier to enter the conversation while theother party is talking.Detailed instructions for placing and receivinghands-free calls are in your Cellular Telephone UserManual.Battery Option Description You may purchase a battery option for yourAttache/Carry phone which allows you to operate theAttache/Carry phone away from the vehicle. In theAttache model, the battery mounts on top of theInstallation Manual22
transceiver inside the carrying case. In the Carrymodel, the battery mounts in the battery compartmentlocated outside the carry case. Under normaloperating conditions, a fully charged unit will provide70 minutes of continuous talk time before requiringrecharging. The actual time between charges willdepend on many factors, such as the age of thebattery, how often it is recharged, the length andfrequency of phone calls, and the air temperature.Charging the Battery The battery in your Attache/Carry phone can becharged using the cigarette lighter receptacle in yourvehicle or the AC charger included with the unit.When charging the Attache/Carry phone using thevehicle cigarette lighter receptacle, the battery willcharge at various rates depending upon whether thetelephone is ‘on’, whether it is being used to place acall, your vehicle’s engine speed, and the number ofaccessories (e.g., air conditioning, blower, windowdefrosters, etc.) that are in operation in your vehicle.The best circumstances for charging your battery arewhen your vehicle is operating at highway speed,there are few accessories in operation, and thetelephone is either ‘off’, or ‘on’ but not in a call. Underthese circumstances, the battery will fully charge inabout 3 hours. In other circumstances, your vehiclewill provide a trickle charge to your battery, so youcan use the Attache/Carry phone in your vehicle whileits battery is recharging, but the recharging time willbe extended.Installation Manual23
It should be noted that the Attache/Carry phone willoperate in a vehicle, using the cigarette lighterreceptacle, even if the Attache/Carry phone battery iscompletely discharged.The AC charger will fully charge your Attache/Carryphone battery in about 10 hours. There is also anoptional rapid charger available that will charge yourAttache/Carry phone battery in 3 hours.The Attache/Carry phone can be used while it isconnected to the AC charger, provided that thebattery is at least partially charged. When connectedto the AC charger, if the battery is completelydischarged, the battery should be partially rechargedbefore you attempt to use the Attache/Carry phone.Battery Care The useful lifetime of a rechargeable battery isaffected by how it is used and how often it isrecharged. The Attache/Carry phone battery is asealed lead acid battery that is somewhat similar tothe battery used in your car. Unlike some other typesof batteries, your Attache/Carry phone battery is notsubject to the ‘memory affect’ associated with frequentcharging. In fact, it is best to charge your battery asoften as possible. Your battery’s lifetime will also beextended if you avoid fully discharging the battery.It is also important to remember to always store,operate, and charge your battery in a well ventilatedarea. This battery should NEVER be placed in anairtight container. Also, to avoid damaging the battery,NEVER allow a paper clip, or other metal object toInstallation Manual24
rest across the terminals of the battery. In addition,DO NOT puncture the battery, or dispose of it in a fire.Using Spare Batteries You may remove the battery and replace it with acharged spare battery. See your cellular telephonesales representative to purchase spare batteries.WARNING Do not use a nickel cadmium battery withthis product. It is not compatible with the chargingmethod, and may burst.Field Installation of the Battery Option for Attache Phone ModelIf your unit was purchased without the battery option,a battery conversion kit may be purchased andinstalled. This kit consists of a battery, battery charger,and a battery clip connector. The installation shouldbe performed according to the instructions below.Step 1 Turn the unit off by pressing ∏ on thehandset.Step 2 Disconnect the handset modular connectorfrom the jack located on the side of thetransceiver.Step 3 Unzip the transceiver compartment andcarefully remove the transceiver and powerconnector assembly.Step 4 Follow steps 5 –7 of the assembly procedure,beginning on page 2.Installation Manual25
Field Installation of the Battery Option for Carry Phone ModelIf your unit was purchased without the battery option,a battery conversion kit may be purchased andinstalled. This kit consists of a battery, battery charger,and a battery clip connector. The installation shouldbe performed by following Steps 7-8 of the assemblyprocedure beginning on page 7.Installation Manual26
Mobile InstallationPlanning and InstallationTransceiver LocationIn many vehicles the best location for the transceiverunit is the floor of the trunk compartment; alternatelocations are under the dash, under the front or rearseat, and under the rear speaker deck panel.Regardless of the location choice, be sure thetransceiver unit is protected from dirt and moistureand that there is sufficient space around thetransceiver unit to allow airflow and removal. Also,allow for adequate clearances for the control/powercable connector and antenna coaxial cable.Standard Transceiver Mounting Bracket InstallationInstall the standard mounting bracket as follows:Horizontal MountingStep 1 Use the mounting bracket fitted over thetransceiver as a template to determine themounting screws’ (2) locations. Be sure to firstsnap the mounting bracket over thetransceiver, since the bracket will flex. Alsonote the mounting bracket only fits one way.Be sure that the selected mounting locationallows for adequate airflow for the transceiver.Step 2 Place the mounting bracket on the selectedmounting surface. Mark the locations for thetwo mounting screws.Installation Manual27
Step 3 Center punch the screws’ locations. Drill 1/8inch holes for the mounting screws.WARNING Be careful to avoid drilling into thefuel tank or other vital part of the vehicle.Step 4 With the transceiver in place under themounting bracket, secure the bracket to themounting surface using the self-tapping screwsand lock washers provided in the fuse kit.Vertical MountingFollow the same procedures for horizontal mountingexcept for the two mounting screws. In place of themounting screws, use two suitable size bolts, nuts,and washers (installer supplied). Place a lock washerbetween each bolt and the mounting bracket, insert thebolts through the bracket and holes drilled in mountingsurface, and secure with flat washers and nuts.Handset LocationConsider the following factors when deciding thehandset mounting location:•The mounting surface must have sufficient strengthto support the handset.•The handset must be within easy reach of the driverduring normal operation of the vehicle and shouldnot interfere with the driver’s or passenger’s seatingor leg space.•The handset must also be within reach of thehandset end of the control/power cable.Installation Manual28
Figure 228-18 x 1"Mounting ScrewsMounting BracketTransceiverAntenna ConnectorMounting SurfaceInstallation Manual29
Control Unit Mounting Cup InstallationThe control unit mounting cup is used to hold thecontrol unit handset.Figure 23Adjustable Angle Mounting Bracket Installation (optional)The adjustable angle mounting bracket provides aconvenient means for mounting the control unit. In atypical application, the control unit hang-up cupmounts directly to the adjustable angle mountingbracket. Install the adjustable angle mounting bracketas follows:Step 1 Temporarily position the control unit andmounting bracket to verify the desiredmounting location. Check for clearance andRubber Tip Bumper (2)Machine Screws (4)M4 x 0.7 x 10 UpperShellInstallation Manual30
operating convenience. Using the surfacebase as a guide, mark four holes on thetransmission hump or other selected location.The four mounting tabs on the surface baseare somewhat flexible to conform to a curvedsurface as necessary.Step 2 Using an awl or similar device, open fourholes in the carpet at marked locations. Thismust be done prior to drilling to avoid ruiningthe carpet.Step 3 Using a 3.2 mm (1/8") bit, drill the fourmounting holes and secure the surface baseusing the four 8-1/8 x 3/4" tapping screwsprovided.Step 4 Mount the base to the surface base at thedesired angle and securely tighten the angle-adjusting screws.Installation Manual31
Figure 24Antenna LocationThe best location for the antenna is at the center ofthe vehicle roof, or on glass near the roof. Motorolaoffers (as an option) a ‘thru-the-glass’ type antennawhich should be mounted on the vehicle rear window.This type of antenna should be positioned as high onthe window as possible. The inductive ‘button’ on themounting foot must not be crossed by a rear windowdefogger element.Angle-Adjusting Screws (2)(One on each side)Metal Strip with Hole(Four strips are providedto facilitate mounting ofbracket on contoured surfaces)LockWasher (4)INT tooth#8Hex Nut (4)M4 x 0.7SurfaceBase8-1/8 x 3/4"Tapping screws (4)Base0°-110°AdjustableAngleInstallation Manual32
Antenna InstallationIMPORTANT: To meet the FCC’s RF ExposureGuidelines, the antenna should be installed to ensurea minimum distance between the body of the userand nearby persons and the antenna. To determinethe minimum distance, calculate the combined cableloss and antenna gain and refer to the graph below toidentify the required minimum separation distance incentimeters.Hands-Free Microphone InstallationThe mounting position of the Digital HF hands-freemicrophone within the vehicle has a definite influenceon the performance of the Vehicular Speaker Phone(V.S.P.) hands-free operation. The microphone shouldbe mounted either on the sun visor (directly above thedriver) or on the headliner (above the driver). Themicrophone should never be mounted near the windowor in a location where the road and ambient backgroundnoise would be substantially high (above 85 dB SPL).Installation Manual33Combined Cable Loss and Antenna Gain vs. Minimum Separation Distance-4-3-2-101234520 25 30 35 40 45 50Minimum Separation Distance (cm)Combined Cable Loss and Antena Gain (dB)Combined Cable Loss and Antenna Gain vs. Minimum Separation DistanceMinimum Separation Distance (cm)Combined Cable Loss and Antenna Gain (dB)
The visor clip mounting bracket provides the simplestand most effective mounting of the hands-freemicrophone. See Figure 25. The clip slides intochannels on the microphone housing, and then clipson to the sun visor. The cable may then beunobtrusively routed to the Digital HF microphone jacklocated near the power cable connector on the DHFA.Figure 25Optional External Speaker InstallationThe external speaker should be mounted under thedash, on the transmission hump, or in any othersuitable location using the mounting bracket suppliedwith the speaker assembly. The proposed locationmust not interfere with the operation of the vehicle.Also, the speaker must be securely attached to itsSun VisorMounting ClipHands-FreeMicrophoneMicrophoneCableSun VisorInstallation Manual34
mounting bracket. Every effort should be made toavoid locating the speaker behind a sound absorptivebarrier (e.g., facing upward under the seat or behind adashboard panel).CAUTION Do not install either the speaker or DHFAunsupported to prevent shifting of the unit which couldinterfere with the proper operation of the vehicle.Always use the supplied mounting hardware.Control/Power Cable RoutingMany vehicles are equipped with wire troughs in thedoor sills. If the vehicle has this feature, use it toprovide maximum protection for the cables and tosimplify installation. In vehicles without wiring troughs,the power cable must be routed where it will beprotected from pinching, sharp edges, and crushing.To avoid interference with the vehicle’s electronics, donot run cables above the catalytic converter or nearthe vehicle’s electronic modules. Use grommetswhenever a cable must pass through a hole in a metalpanel. No matter what method of cable routing isimplemented, all in-line connectors must be keptaccessible.The mobile telephone system is designed to operatein negative ground 12-volt electrical systems only.To minimize electrical noise that interferes with thecellular telephone operation, be sure to check thecondition of the ignition wiring and the connections tothe vehicle battery. All wire connections should beclean and tight.Installation Manual35
Control/Power Cable InstallationThe control/power cable provides interconnection ofthe transceiver, handset, microphone (if equipped),and the external speaker (if equipped). See Figure 26for installation diagram. Install the control/power cableas follows:Step 1 Route the control/power cable as previouslyspecified. Do not pull on the connectorhousings while routing the cable.Step 2 Install and route the antenna coaxial cable aspreviously noted. Connect the coaxial cable tothe transceiver and to the antenna.Step 3 Remove all fuses and tape them to theirrespective holders.Step 4 Bolt the black lead(s) of the power/controlcable to a suitable grounded point on thevehicle frame using the ring lug provided.NOTE Special attention should be given to locating agood vehicle ground. Optimum radio performance canonly be achieved with a ground connection having avery low resistance. The vehicle frame makes the bestground, but body structural reinforcement membersare also suitable for grounding purposes. Verify thatthe connections between the battery negativeterminal, vehicle chassis, and engine block have lowresistance. If it becomes necessary to run the blacklead to the battery, the lead must be fused with a 10-amp fuse.Installation Manual36
Figure 26Step 5 Connect the D-type connector on the powercable, and the modulator connector on thecontrol cable, to the transceiver.Step 6 Check the power cable fuses and make surethat the correct sizes and types are supplied.Step 7 The green/black ignition sense lead of thepower cable should normally be connected toTo Lights,Horn, etc.2 AmpereBlue CrimpConnector(not supplied)AUX AlertYellow/BlackSpeakerDigitalHands-FreeMicrophone10 AmpereBlue CrimpConnectorBlack4 AmpereBlue CrimpConnectorIgnitionSenseGreen/BlackAntennaTransceiverControl CableHandsetChassisGroundChassisGroundBatteryPower CableRelay(500 mA max.coil rating)RedIgnitionSwitchIn-LineSpliceInstallation Manual37
an accessory terminal at the vehicle fuseblock, through the green wire of the fuseholder assembly. For proper operation of theconvenience on/off feature, the accessoryterminal voltage should go to A + with theignition switch on, then go low while crankingthe starter, then return to A + with the vehiclerunning. If the ignition sense lead is left unter-minated, the mobile must be turned on with∏ on the handset, and it will always turn onlocked. Cut and strip the green wire connectedto the fuse holder (to position the fuse in thedesired location) and connect one end to aconvenient point on the wire coming from theappropriate accessory terminal using the in-line splice. Connect the other end to thegreen/black ignition sense lead on the powercable, using the blue crimp-style connector.Step 8 The yellow/black auxiliary alert lead of thepower cable provides a ground for the first fivetimes that the mobile unit rings. The groundhas a fixed duration of one second for eachring. Although the auxiliary alert line has a 1/2ampere capacity, it is recommended that theconnection to the auxiliary alert device (suchas the vehicle horn, headlights, etc.) be madethrough a suitable relay using a 2A slow-blowfuse for circuit protection. The auxiliary alertfeature must be activated by the telephoneuser prior to turning off the car. Ignition sensemust be low in order to use the auxiliary alertfeature. If this feature is not desired, theInstallation Manual38
yellow/black lead may be left unterminated.NOTE Local regulations may forbid the use ofhorns and/or flashing headlights as auxiliaryalert devices. Consequently, the auxiliary alertexternal signaling feature should not be usedin these areas.Step 9 Cut and strip the red wire(s) connected to thefuse holder (to position the fuse in the desiredlocation) and connect one end to the positivebattery terminal using the lug supplied.Connect the other end to the red A + wire onthe power cable, using the blue crimp-styleconnector.Step 10Connect the external speaker and microphoneconnectors (if equipped) to the speaker andmicrophone jacks on the control/power cables.(It is recommended that the plugs not beinstalled in an area exposed to excessivemoisture.)Step 11 Carefully inspect all cables andconnections; then insert the 10A fuse into thefuse holder on the red lead and the 4A fuseinto the fuse holder on the green/black lead.Performance ChecksChecking PerformanceOnce the mobile telephone has been installed, itsperformance should be checked using the followingprocedure. Refer to the User Manual for instructionson how to turn on, unlock, and place calls.Installation Manual39
Installation Manual40Step 1 Place a call from the mobile and confirmproper operation. Use both the handset andthe optional hands-free during this call if thephone is so equipped.Step 2 Have a call placed to the mobile and confirmproper operation. Use both the handset andthe optional hands-free during this call if thephone is so equipped.Step 3 If you experience difficulty placing andreceiving calls, check the voltage standingwave ratio (VSWR) using the followingmethod. Measure the power output of theradio with the radio connected to the vehicleantenna through a directional watt meter.Measure the forward power and reflectedpower with the watt meter and compute theVSWR as follows:The VSWR should be less than 2:1. If theVSWR is greater than 2, check the antennaand its cable connector.Checking Auxiliary Alert FeatureStep 1 Prepare the unit to receive test calls byenabling the auxiliary alert feature, inaccordance with the procedures provided inthe User Manual. Place a test call to themobile.voltage standing wave ratio =where R = reflected powerforward power1+R1-R
Installation Manual41Step 2 Verify the alert device has been activated bythe incoming call and then answer the call.Step 3 With the auxiliary alert feature enabled, placea second test call to the mobile. Do notanswer the call. Verify that after approximately20 seconds (5-6 rings), the alert device hasbeen deactivated and that the handsetdisplays CALL after being enabled in themanner described in the User Manual.
Before Calling for ServiceAfter installation, programming, and performancecheckout, your cellular telephone is ready foroperation. If you experience operating difficulties,check the following before making a call for service:Have you read your User Manual?Everything you need to know to operate your cellulartelephone is in your User Manual. Take the time toread it and become familiar with all the features ofyour telephone before calling for service. Note that notall of the features discussed below are included in alltelephone models.If your telephone is equipped with digital hands-free(with an external microphone), do you hear excessivefeedback noise during a hands-free call?Because of audio variations in the cellular system,excessive feedback noise or howling may sometimesbe heard when a full duplex (if your telephone is soequipped) hands-free call is placed or received. If thisoccurs, decrease the speaker volume using thevolume control on the handset. Also, verify that themicrophone was not installed in an area of the vehiclethat is subject to high background noise (above 85 dBSPL). More information about hands-free operationcan be found in your User Manual.Installation Manual42
If your telephone is equipped with the integratedhands-free microphone, do you hear excessivefeedback noise during a hands-free call? Check your User Manual to be sure you have enabledEnhanced Simplex Hands-free Operation. See yourUser Manual for further details.Have you unlocked your unit?Your cellular telephone is inoperative when locked.This state is indicated by LOCKED in the display. Tounlock the telephone, enter your three-digit unlockcode. LOCKED will disappear.Does the red No Svc message continue to display?This may indicate that you are outside of the servicearea, or in a marginal reception area. Marginalreception may also be indicated by the fast busy oralternating high-low sound when attempting to place acall.Have you programmed a unique operating mode intothe unit?Constant flashing of the Roam indicator or illuminationof the No Svc indicator while in your home servicearea may indicate an undesired roam characteristicchoice has been selected. See ‘Selectable SystemRegistration’ or ‘Roaming’, in the User Manual.Installation Manual43
General Safety InformationRead this information before using your mobilecellular car telephone.The cellular telephone is one of the most exciting andinnovative electronic products ever developed. With ityou can stay in contact with your office, your home,emergency services, and others.For the safe and efficient operation of your phone,observe these guidelines.Your mobile cellular telephone is a radio transmitterand receiver. When the phone is on, the externallymounted antenna is the part of the phone that sendsout and receives radio frequency (RF) energy. Thephone operates in the frequency range of 824 MHz to894 MHz and employs commonly used frequencymodulation (FM) techniques. When you use yourphone, the cellular system handling your call controlsthe power level at which your phone transmits. Thepower level can range from 0.005 of a watt to 3 watts.Exposure to Radio Frequency EnergyIn 1991 the Institute of Electrical and ElectronicsEngineers (IEEE), and in 1992 the American NationalStandards Institute (ANSI), adopted the 1982 ANSIStandard for safety levels with respect to humanexposure to RF energy. Over 120 scientists,engineers, and physicians from universities,government health agencies, and industry, afterreviewing the available body of research, developedthis updated Standard. In March, 1993 the FederalCommunications Commission (FCC) proposed theInstallation Manual44
adoption of this updated Standard. To operate withinthis updated ANSI Standard, use your phone asdescribed under ‘Safe and Efficient Phone Operation’.Safe and Efficient Phone OperationDo not operate your mobile cellular telephone when aperson is within 4 inches (10 centimeters) of theantenna unless that person is shielded from theantenna by a metal surface such as the roof of thecar. Otherwise you may impair call quality, may causeyour phone to operate at a higher power level than isnecessary, and may expose that person to RF energyin excess of that established by the updated ANSIStandard.Antenna Care and ReplacementDo not use the phone with a damaged antenna.Replace a damaged antenna immediately. Consultyour manual to see if you may change the antennayourself. If so, use only a manufacturer-approvedantenna. Otherwise, have your antenna repaired by aqualified technician.Use only the supplied or approved antenna.Unauthorized antennas, modifications or attachmentscould damage the phone and may violate FCCregulations.Installation Manual45
DrivingCheck the laws and regulations on the use of cellulartelephones in the areas where you drive. Always obeythem. Also, when using your phone while driving, please:• give full attention to driving,• use hands-free operation, if available, and• pull off the road and park before making oranswering a call if driving conditions so require.Vehicle Electronic EquipmentRF energy may affect some electronic systems inmotor vehicles. Check with your vehiclemanufacturer’s representative to be sure your phonewill not affect the electronic systems of your vehicle.ChildrenDo not allow children to play with your phone. It is nota toy. Children could damage the phone, or makecalls that increase your telephone bills.Blasting AreasTo avoid interfering with blasting operations, turn yourunit off when in a ‘blasting area’ or in areas posted:‘turn off two-way radio’. Construction crews often useremote control RF devices to set off explosives.Potentially Explosive AtmospheresTurn your phone off when in any area with apotentially explosive atmosphere. It is rare, but yourphone or its accessories could generate sparks.Sparks in such areas could cause an explosion or fireresulting in bodily injury or even death.Installation Manual46
Areas with a potentially explosive atmosphere areoften, but not always, clearly marked. These areasmay include fueling areas such as gas stations; fuel orchemical transfer or storage facilities; and areaswhere you would normally be advised to turn off yourengine.Do not transport or store flammable gas, liquid, orexplosives in the compartment of your vehicle whichcontains your phone or accessories.Vehicles powered by liquefied petroleum gas (such aspropane or butane) must comply with National FireProtection Standard (NFPA-58). For a copy of thisstandard, contact the National Fire ProtectionAssociation, One Batterymarch Park, Quincy, MA02269, Attn: Publications Sales Division.Other Electronic EquipmentMost modern electronic equipment - for example,personal medical devices, equipment in hospitals andcars - is shielded from RF energy. However, RFenergy from cellular telephones may affect someelectronic equipment.Consult your physician or ask the manufacturer of anypersonal medical device (such as pacemakers,hearing aids, etc.) to determine if they are adequatelyshielded from external RF.When using your phone as a carry phone, turn it off inhealth care facilities when any regulations posted inthe areas instruct you to do so. Always requestpermission before using your carry phone nearmedical equipment.Installation Manual47
Aircraft (Carry Phone Configuration Only)Turn your phone off before boarding any aircraft.• Use it on the ground only with crew permission.• Do not use it in the air.To prevent interference with critical aircraft systems,Federal Aviation Administration (FAA) regulationsrequire you to have permission from a crew memberto use your phone while the plane is on the ground. Toprevent interference with cellular systems, FCCregulations prohibit using your phone while the planeis in the air.The design of Motorola’s cellular telephonescomplies with all applicable RF Safety Standards.Motorola meets the standards and recommendations forthe protection of public exposure to RF electromagneticenergy established by governmental bodies and otherqualified organizations, such as the following:• National Council on Radiation Protection andMeasurements (NCRP). Report 86.• Department of Health and Welfare Canada SafetyCode 6.• Verband Deutscher Elektroinigenieure (VDE) DIN-0848.• Directives of the European Community, DirectorateGeneral V in Matters of Radio FrequencyElectromagnetic Energy.• National Radiological Protection Board of the UnitedKingdom GS-11, 1988.• American National Standards Institute (ANSI) / IEEEC95.1-1992.Installation Manual48
Magnetic Storage MediaYour phone contains a magnet. Do not place yourphone in close proximity to magnetic storage mediasuch as diskettes or credit cards for extended periodsof time.BatteriesCAUTION To prevent injuries or burns, do not allowmetal objects to contact or short circuit the batteryterminals.Installation Manual49
Rules, Regulations, andPrecautionsThe U. S. Federal Communications Commission andthe Canadian Department of Communicationsregulate cellular radiotelephone service in theirrespective countries. It is important for you, thecellular radiotelephone user, to observe the applicableregulations when operating your cellular phone ineither country. In addition to these U.S. and Canadianregulations, you may also be bound by certain state,provincial, territorial, and local rules and regulations,as well as by your cellular carrier’s tariff (the rates,terms, and conditions of its service). If you wish to useyour cellular radiotelephone in both the U.S. andCanada, please consult with your system operator.Furthermore, you should remember that your cellularphone is a radiotelephone, – i.e., it combines bothwireline technology, as used in your home or officetelephone system, and radio technology – and thatthe scope of regulations and precautions is thereforebroader than the scope of regulations and precautionsrelating to wireline-only telephone usage.Some of the major points of consideration are set outbelow. Please note, however, that this “Rules,Regulations, and Precautions” section does notconstitute legal advice; and is intended merely forgeneral information purposes. If you have any specificquestions, please contact your Cellular Carrier(System Operator).Installation Manual50
License - If your home system is in the U. S., you donot require a separate license to operate your cellulartelephone; obtaining a cellular telephone accessnumber is sufficient to register you as a user. If yourhome system is in Canada, a separate license isrequired; your carrier will assist you in the licensingprocess. If you wish to use your cellular phone onboth sides of the border, please contact your CellularCarrier (System Operator).Denial of Service - A cellular carrier may deny servicetemporarily, or terminate service for violation of anygovernment regulations or of its tariff.Consumer Responsibilities - Remember that thewireline and radio regulations with respect toharassing calls, false distress calls, obscenelanguage, etc. apply to cellular phone usage.Privacy - As a telephone user, you have come toassume a certain standard of privacy when you place orreceive a telephone call via the traditional wirelinesystems. However, because cellular radiotelephonesutilize radio transmissions to effect calls, the samestandard cannot always be assured. While it is unlawfulfor an unauthorized person to divulge or use anyinformation obtained from intercepting or “listening inon” conversations intended for others, you should notassume that your conversation is completely secure.Commercially available scanning equipment can permita third party to monitor the radio channels used forcellular telephone calls.Interference - No person shall interfere with or causeinterference to any radio communication or signal.Installation Manual51
Equipment Modifications - The U.S. FederalCommunications Commission has type-approved andthe Canadian Department of Communications hasgranted technical acceptance to the model of cellulartelephone which you have purchased, and both haveallocated a specific frequency range for cellularservice. No changes or adjustments are to be madeto your cellular phone.Installation Manual52
Pan American Cellular Subscriber Group600 North U.S. Highway 45Libertyville, Illinois 600481-800-331-6456 – U.S.A.1-800-461-4575 – Canada6809383A19-B01/31/00-RGC©Motorola, Inc. 1995All Rights ReservedPrinted in U.S.A.

Navigation menu