Motorola Solutions 89FC5809 900 MHz Fixed Wireless (ISM) User Manual Exh D Manual

Motorola Solutions, Inc. 900 MHz Fixed Wireless (ISM) Exh D Manual

Contents

Exh D Manual

900-UG-enIssue 1, Draft 1June 2004CanopyTM 900 MHzAccess Point (AP) andSubscriber Module (SM)User GuideSoftware Release Notes
Canopy 900 MHz AP and SM User GuideIssue 1, Draft 1 June, 2004 Page 2 of 16NOTICESImportant Note on ModificationsIntentional or unintentional changes or modifications to the equipment must not be made unless under the express consent of the partyresponsible for compliance. Any such modifications could void the user’s authority to operate the equipment and will void themanufacturer’s warranty.U.S. Federal Communication Commission (FCC) and Industry Canada (IC) NotificationThis device complies with part 15 of the U. S. FCC Rules and Regulations and with RSS-210 of Industry Canada. Operation issubject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept anyinterference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the U.S. FCCRules and with RSS-210 of Industry Canada. These limits are designed to provide reasonable protection against harmful interferencein a residential installation. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used inaccordance with these instructions, may cause harmful interference to radio communications. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged tocorrect the interference by one or more of the following measures:• Increase the separation between the affected equipment and the unit;• Connect the affected equipment to a power outlet on a different circuit from that which the receiver is connected to;• Consult the dealer and/or experienced radio/TV technician for help.FCC IDs and Industry Canada Certification Numbers are listed in the following table:NOTE: FCC and Industry Canada Testing is in Progress. The following table isprovisional until certification.ModuleTypesOperating FrequencyRangeMaximumTransmitterPowerReflector or AntennaFCC IDIndustry CanadaCertificationNumberSM APISM 902 to 928 MHz1WMaxrad Model # Z1681, flat panelwith 10 dBi gainMars Model # MA-IS91-T2, flatpanel with10 dBi gainMTI Model #MT-2630003/N, flatpanel with 10 dBi gainABZ89FC5809109W-9000ISMExposure NoteThe antenna of a Canopy 900 MHz module must be installed to provide a separation distance of at least 80 cm (approx 32 in) from allpersons. When so installed, the module’s RF field is within Health Canada limits for the general population; consult Safety Code 6,obtainable from Health Canada’s website http://www.hc-sc.gc.ca/rpb.The maximum RMS power does not exceed 1W.The applicable power density exposure limit is 10 Watt/m2, according to the FCC OET Bulletin 65, the ICNIRP guidelines, and theHealth Canada Safety Code 6. The corresponding compliance distances referenced above have been determined by assuming worst-case scenarios. The peak power density (S) in the far-field of a radio-frequency source with rms transmit power P and antenna gain Gat a distance d is24dGPSπ⋅=In the case of a 900 MHz Canopy SM or AP with an antenna gain of 10 dBi (a factor of 10) and correctly entered in the user interfaceas a 10 dBi gain antenna, the peak power density equals the exposure limit at a distance of 18 cm. A power compliance margin of over20 is artificially introduced by setting the distance to 80 cm.Consider next the case of a 900 MHz Canopy SM or AP with a 12 dBi antenna (a factor of 15.85) set in error in the user interface asan 8 dBi gain antenna. In this case, the peak power density equals the exposure limit at a distance of 36 cm, still giving a powercompliance margin of over 5.The compliance distance is greatly overestimated in these cases because the far-field equation neglects the physical dimension of theantenna, which is modeled as a point-source.Software License Terms and ConditionsONLY OPEN THE PACKAGE, OR USE THE SOFTWARE AND RELATED PRODUCT IF YOU ACCEPT THE TERMS OFTHIS LICENSE. BY BREAKING THE SEAL ON THIS DISK KIT / CDROM, OR IF YOU USE THE SOFTWARE OR RELATEDPRODUCT, YOU ACCEPT THE TERMS OF THIS LICENSE AGREEMENT. IF YOU DO NOT AGREE TO THESE TERMS, DO
Canopy 900 MHz AP and SM User GuideIssue 1, Draft 1 June, 2004 Page 3 of 16NOT USE THE SOFTWARE OR RELATED PRODUCT; INSTEAD, RETURN THE SOFTWARE TO PLACE OF PURCHASEFOR A FULL REFUND. THE FOLLOWING AGREEMENT IS A LEGAL AGREEMENT BETWEEN YOU (EITHER ANINDIVIDUAL OR ENTITY), AND MOTOROLA, INC. (FOR ITSELF AND ITS LICENSORS). THE RIGHT TO USE THISPRODUCT IS LICENSED ONLY ON THE CONDITION THAT YOU AGREE TO THE FOLLOWING TERMS.Now, therefore, in consideration of the promises and mutual obligations contained herein, and for other good and valuableconsideration, the receipt and sufficiency of which are hereby mutually acknowledged, you and Motorola agree as follows:Grant of License. Subject to the following terms and conditions, Motorola, Inc., grants to you a personal, revocable, non-assignable,non-transferable, non-exclusive and limited license to use on a single piece of equipment only one copy of the software contained onthis disk (which may have been pre-loaded on the equipment)(Software). You may make two copies of the Software, but only forbackup, archival, or disaster recovery purposes. On any copy you make of the Software, you must reproduce and include thecopyright and other proprietary rights notice contained on the copy we have furnished you of the Software.Ownership. Motorola (or its supplier) retains all title, ownership and intellectual property rights to the Software and any copies,including translations, compilations, derivative works (including images) partial copies and portions of updated works. The Softwareis Motorola’s (or its supplier's) confidential proprietary information. This Software License Agreement does not convey to you anyinterest in or to the Software, but only a limited right of use. You agree not to disclose it or make it available to anyone withoutMotorola’s written authorization. You will exercise no less than reasonable care to protect the Software from unauthorized disclosure.You agree not to disassemble, decompile or reverse engineer, or create derivative works of the Software, except and only to the extentthat such activity is expressly permitted by applicable law.Termination. This License is effective until terminated. This License will terminate immediately without notice from Motorola orjudicial resolution if you fail to comply with any provision of this License. Upon such termination you must destroy the Software, allaccompanying written materials and all copies thereof, and the sections entitled Limited Warranty, Limitation of Remedies andDamages, and General will survive any termination.Limited Warranty. Motorola warrants for a period of ninety (90) days from Motorola’s or its customer’s shipment of the Software toyou that (i) the disk(s) on which the Software is recorded will be free from defects in materials and workmanship under normal useand (ii) the Software, under normal use, will perform substantially in accordance with Motorola’s published specifications for thatrelease level of the Software. The written materials are provided "AS IS" and without warranty of any kind. Motorola's entire liabilityand your sole and exclusive remedy for any breach of the foregoing limited warranty will be, at Motorola's option, replacement of thedisk(s), provision of downloadable patch or replacement code, or refund of the unused portion of your bargained for contractualbenefit up to the amount paid for this Software License.THIS LIMITED WARRANTY IS THE ONLY WARRANTY PROVIDED BY MOTOROLA, AND MOTOROLA AND ITSLICENSORS EXPRESSLY DISCLAIM ALL OTHER WARRANTIES, EITHER EXPRESS OF IMPLIED, INCLUDING BUTNOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ANDNONINFRINGEMENT. MOTOROLA DOES NOT WARRANT THAT THE OPERATION OF THE SOFTWARE WILL BEUNINTERRUPTED OR ERROR-FREE, OR THAT DEFECTS IN THE SOFTWARE WILL BE CORRECTED. NO ORAL ORWRITTEN REPRESENTATIONS MADE BY MOTOROLA OR AN AGENT THEREOF SHALL CREATE A WARRANTY ORIN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY. MOTOROLA DOES NOT WARRANT ANY SOFTWARETHAT HAS BEEN OPERATED IN EXCESS OF SPECIFICATIONS, DAMAGED, MISUSED, NEGLECTED, OR IMPROPERLYINSTALLED. BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IMPLIEDWARRANTIES, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.Limitation of Remedies and Damages. Regardless of whether any remedy set forth herein fails of its essential purpose, IN NOEVENT SHALL MOTOROLA OR ANY OF THE LICENSORS, DIRECTORS, OFFICERS, EMPLOYEES OR AFFILIATES OFTHE FOREGOING BE LIABLE TO YOU FOR ANY CONSEQUENTIAL, INCIDENTAL, INDIRECT, SPECIAL OR SIMILARDAMAGES WHATSOEVER (including, without limitation, damages for loss of business profits, business interruption, loss ofbusiness information and the like), whether foreseeable or unforeseeable, arising out of the use or inability to use the Software oraccompanying written materials, regardless of the basis of the claim and even if Motorola or a Motorola representative has beenadvised of the possibility of such damage. Motorola's liability to you for direct damages for any cause whatsoever, regardless of thebasis of the form of the action, will be limited to the price paid for the Software that caused the damages. THIS LIMITATION WILLNOT APPLY IN CASE OF PERSONAL INJURY ONLY WHERE AND TO THE EXTENT THAT APPLICABLE LAWREQUIRES SUCH LIABILITY. BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATIONOF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TOYOU.Maintenance and Support. Motorola shall not be responsible for maintenance or support of the software. By accepting the licensegranted under this agreement, you agree that Motorola will be under no obligation to provide any support, maintenance or service inconnection with the Software or any application developed by you. Any maintenance and support of the Related Product will beprovided under the terms of the agreement for the Related Product.Transfer. In the case of software designed to operate on Motorola equipment, you may not transfer the Software to another partyexcept: (1) if you are an end-user, when you are transferring the Software together with the Motorola equipment on which it operates;or 2) if you are a Motorola licensed distributor, when you are transferring the Software either together with such Motorola equipmentor are transferring the Software as a licensed duly paid for upgrade, update, patch, new release, enhancement or replacement of a priorversion of the Software. If you are a Motorola licensed distributor, when you are transferring the Software as permitted herein, youagree to transfer the Software with a license agreement having terms and conditions no less restrictive than those contained herein.
Canopy 900 MHz AP and SM User GuideIssue 1, Draft 1 June, 2004 Page 4 of 16You may transfer all other Software, not otherwise having an agreed restriction on transfer, to another party. However, all suchtransfers of Software are strictly subject to the conditions precedent that the other party agrees to accept the terms and conditions ofthis License, and you destroy any copy of the Software you do not transfer to that party. You may not sublicense or otherwisetransfer, rent or lease the Software without our written consent. You may not transfer the Software in violation of any laws,regulations, export controls or economic sanctions imposed by the U.S. Government.Right to Audit. Motorola shall have the right to audit annually, upon reasonable advance notice and during normal business hours,your records and accounts to determine compliance with the terms of this Agreement.Export Controls. You specifically acknowledge that the software may be subject to United States and other country export controllaws. You shall comply strictly with all requirements of all applicable export control laws and regulations with respect to all suchsoftware and materials.U.S. Government Users. If you are a U.S. Government user, then the Software is provided with "RESTRICTED RIGHTS" as setforth in subparagraphs (c)(1) and (2) of the Commercial Computer Software-Restricted Rights clause at FAR 52 227-19 orsubparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013, as applicable.Disputes. You and Motorola hereby agree that any dispute, controversy or claim, except for any dispute, controversy or claiminvolving intellectual property, prior to initiation of any formal legal process, will be submitted for non-binding mediation, prior toinitiation of any formal legal process. Cost of mediation will be shared equally. Nothing in this Section will prevent either party fromresorting to judicial proceedings, if (i) good faith efforts to resolve the dispute under these procedures have been unsuccessful, (ii) thedispute, claim or controversy involves intellectual property, or (iii) interim relief from a court is necessary to prevent serious andirreparable injury to that party or to others.General. Illinois law governs this license. The terms of this license are supplemental to any written agreement executed by bothparties regarding this subject and the Software Motorola is to license you under it, and supersedes all previous oral or writtencommunications between us regarding the subject except for such executed agreement. It may not be modified or waived except inwriting and signed by an officer or other authorized representative of each party. If any provision is held invalid, all other provisionsshall remain valid, unless such invalidity would frustrate the purpose of our agreement. The failure of either party to enforce any rightsgranted hereunder or to take action against the other party in the event of any breach hereunder shall not be deemed a waiver by thatparty as to subsequent enforcement of rights or subsequent action in the event of future breaches.Hardware Warranty in U.S.Motorola U.S. offers a warranty covering a period of 1 year from the date of purchase by the customer. If a product is found defectiveduring the warranty period, Motorola will repair or replace the product with the same or a similar model, which may be areconditioned unit, without charge for parts or labor.IN NO EVENT SHALL MOTOROLA BE LIABLE TO YOU OR ANY OTHER PARTY FOR ANY DIRECT, INDIRECT,GENERAL, SPECIAL, INCIDENTAL, CONSEQUENTIAL, EXEMPLARY OR OTHER DAMAGE ARISING OUT OF THE USEOR INABILITY TO USE THE PRODUCT (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESSPROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION OR ANY OTHER PECUNIARY LOSS, ORFROM ANY BREACH OF WARRANTY, EVEN IF MOTOROLA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCHDAMAGES. (Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion orlimitation may not apply to you.) IN NO CASE SHALL MOTOROLA’S LIABILITY EXCEED THE AMOUNT YOU PAID FORTHE PRODUCT.Trademarks, Product Names, and Service NamesMOTOROLA, the stylized M Logo and all other trademarks indicated as such herein are trademarks of Motorola, Inc. ® Reg. U.S. Pat& Tm. Office. Canopy is a trademark of Motorola, Inc. All other product or service names are the property of their respectiveowners.© 2004 Motorola, Inc. All rights reservedhttp://www.motorola.com/canopy
Canopy 900 MHz AP and SM User GuideIssue 1, Draft 1 June, 2004 Page 5 of 16Table of Contents1 Introduction ________________________________________________________ 61.1 Document Change History _______________________________________________61.2 Feedback on Documentation _____________________________________________61.3 Technical Support______________________________________________________72 Feature Description and Operation _____________________________________ 82.1 3.3 Mbps Signaling Rate _________________________________________________ 82.2 Network Features Identical to 5.2 GHz, 5.7 GHz, and 2.4 GHz__________________ 82.3 Available as AP and SM – no Backhaul ____________________________________ 92.4 Three non-overlapping channels __________________________________________92.5 Range of 40 Miles LOS, Significant Foliage Penetration NLOS ________________ 102.6 Modules and Antennas available _________________________________________ 112.7 Spectrum Analyzer ____________________________________________________ 132.8 Remote AP without Tower ______________________________________________ 142.9 900 MHz Modules Use Release 4.2.2 ______________________________________ 143 900 MHz AP and SM Specifications ___________________________________ 15List of FiguresFigure 1: Link Capacity Test_____________________________________________________________ 8Figure 2: Highlights of 900 MHz AP Configuration Page _____________________________________ 10Figure 3: Subscriber 900 MHz Flat Panel Antenna __________________________________________ 11Figure 4: Additional 900 MHz Flat Panel Antenna___________________________________________ 12Figure 5: 900 MHz SM Spectrum Analyzer_________________________________________________ 14
Canopy 900 MHz AP and SM User GuideIssue 1, Draft 1 June, 2004 Page 6 of 161 IntroductionThis guide is designed for operators already familiar with the Canopy system who only want the “delta” or“difference” information for the Canopy 900 MHz Access Point and Subscriber Module. The informationin this guide will be included in appropriate sections of the Canopy documentation set.• If you are familiar with the Canopy system, want to know what is new with the 900 MHz modules,and don’t want to search through the general Canopy manuals, this guide is for you.• If you are new to the Canopy system or need information across all the products and frequencybands in the Canopy family, you should use the general Canopy manuals, not this “differences” userguide.To ensure you have the latest user information, check the manuals section of the Canopy web site athttp://motorola.canopywireless.com/support_library.php#manual-en.The following abbreviations are used throughout these notes:BHBackhaul Module, either timing master or timing slaveBHMBackhaul Module – timing masterBHSBackhaul Module – timing slaveAPAccess Point ModuleSMSubscriber Module1.1 Document Change HistoryIssue 1 Draft 1• Succeeds Beta Issue 4• Deleted information on integrated antenna. Informationwill be included in a future issue (Issue 2 or beyond)after FCC approval of the integrated antenna• Added exposure information and recommendeddistance• Emphasized requirement that external antennas beprofessionally installed1.2 Feedback on DocumentationWe welcome your feedback on Canopy documentation. Comments on structure, content, accuracy,completeness, or any other area are appreciated. Please send your feedback to technical-documentation@canopywireless.com.
Canopy 900 MHz AP and SM User GuideIssue 1, Draft 1 June, 2004 Page 7 of 161.3 Technical SupportIf problems arise, the Canopy support team is here to help. Here is the escalation path for resolution of aproblem:1. Check this document.2. Escalate the problem to your Canopy supplier.3. Escalate the problem to Canopy Technical Support or other designated Tier 3 technical support:Canopy Technical Support email: technical-support@canopywireless.com1 888 605 2552 or+1 217 824 9742Hours of Operation:Mon - Sun, 7am-11pm US Eastern Standard TimeWhen you send e-mail or call, please include the following information:• Information on your network configuration, especially IP addresses and MAC addresses.• Version numbers of the software on the modules with problems.
Canopy 900 MHz AP and SM User GuideIssue 1, Draft 1 June, 2004 Page 8 of 162 Feature Description and OperationEach of the following sections describes features that are new or different or important with theintroduction of Canopy 900 MHz APs and SMs.2.1 3.3 Mbps Signaling RateDescriptionCanopy 900 MHz AP and SM modules operate at 3.3 Mbps (compared to 10 Mbps for other Canopyfrequency bands). With Downlink Data set to 75%, the AP supports high aggregate throughput to an SM.As in other Canopy frequency bands, an AP has more bandwidth than an individual SM – it takes at least 2SMs to fully load an AP.OperationUplink and Downlink rates can be checked using the Link Test page on the AP. On an AP, select ExpandedStats, then Link Test.Figure 1: Link Capacity Test2.2 Network Features Identical to 5.2 GHz, 5.7 GHz, and 2.4 GHzDescriptionCanopy 900 MHz modules run the same software and provide the same network features as all otherCanopy APs and SMs. NAT, color codes, SNMP, authentication, RSSI measurements, jitter measurements,AP connections to a CMM2 or CMMmicro, AES option, and so on all work the same as before.OperationSame operation as other frequency bands.
Canopy 900 MHz AP and SM User GuideIssue 1, Draft 1 June, 2004 Page 9 of 162.3 Available as AP and SM – no BackhaulDescriptionAP and SM modules are available for building 900 MHz Point to Multi-point networks. Backhauls are notprovided, as the narrower bandwidth available in the allocated 900 MHz frequency band does not lenditself to the capacity usually desired for backhauls.2.4 Three non-overlapping channelsDescriptionThe Canopy 900 MHz modules provide 3 non-overlapping channels within the allocated 900 MHzspectrum. Channels are 8 MHz wide, and can be set with RF Frequency Carrier (center of the channel) at906, 907, 911, 915, 919, 923, or 924 MHz. For normal operation, it is recommended that the operator use• 906 MHz for north and south facing APs• 915 MHz for northeast and southwest facing APs• 924 MHz for southeast and northwest facing APsNote, this takes advantage of the spectrum available to provide 9 MHz between channel centers, 1 MHzgreater than the minimum 8 MHz channel size, for additional channel separation.OperationOn the AP Configuration page, set the RF Frequency Carrier parameter to the desired frequency as shownin Figure 2: Highlights of 900 MHz AP Configuration Page.On the SM Configuration page, select/check the desired frequencies in the Custom RF Frequency ScanSelection List.Depending on local practices, this may mean selecting all frequencies to scan (the SM will register to anyfrequency, but takes longer to scan), only one frequency to scan (forces the SM to only register to an AP onthat frequency and minimizes scan time after SM reboot), or the three recommended AP frequencies of906, 915, and 924 MHz (allows for an SM to “switchover” to an AP on another frequency if the one it isregistered to fails or loses signal).
Canopy 900 MHz AP and SM User GuideIssue 1, Draft 1 June, 2004 Page 10 of 16Figure 2: Highlights of 900 MHz AP Configuration Page2.5 Range of 40 Miles LOS, Significant Foliage Penetration NLOSDescriptionThe Canopy 900 MHz modules have a Line-of-Sight (LOS) range of 40 miles (over 64 km), and substantialNon-Line-of-Sight (NLOS) range. NLOS range is dependent on foliage, topography, obstructions, andother RF engineering considerations. The physics of longer-wavelength 900 MHz, the power allowed byregulatory authorities, and the low Canopy Carrier-to-Interference (C/I) ratio combine to support serviceover these increased LOS and NLOS ranges.While the expected typical range in real-world conditions is 40 miles, the AP can be set for a range up to120 miles (over 190 km) to accommodate long shots with very clear Fresnel zone (possibly due to hightower or mountain top location) and quiet RF environment.Setting the range higher tells the software to have a slightly longer switchover time between transmit andreceive to accommodate longer air delay. This reduces the slots per frame available for data, which reducesaggregate throughput at the AP. However, the predictability of Canopy point-to-multi-point throughputcontinues. All SMs served by an AP set to a given range continue to have the same throughput regardlessof their distance from the AP.The 900 MHz modules complement the other frequency bands offered. The 900 MHz modules can be usedto cover a larger area, albeit with lower throughput, than the other frequency bands. Depending on specificoperator requirements, they can be used to penetrate foliage, have greater range, or add additionalsubscribers or additional overall throughput to a tower that is maxed out or can’t use another frequencyband due to interference or tower rights issues.OperationSet the Max Range parameter on the AP Configuration page to the distance of the furthest planned SMfrom the AP cluster, as shown in Figure 2: Highlights of 900 MHz AP Configuration Page.
Canopy 900 MHz AP and SM User GuideIssue 1, Draft 1 June, 2004 Page 11 of 16Important!• Don’t over-set the range. Setting the range higher does not increase the power of the AP.• Setting the range higher reduces aggregate throughput.• All 900 MHz APs in a cluster must be set to the same Max Range.2.6 Modules and Antennas availableNOTE: FCC and IC Testing is in Progress. The text in this section isprovisional until certification.Description900 MHz AP and SM modules are initially available as connectorized units connecting to connectorizedantennas. The following sections describe the module and antenna options.Connectorized AP or SMA connectorized 900 MHz AP or SM uses the same housing as a 2.4, 5.2, and 5.7 GHz module and has a 16inch (approx 40 cm) cable with a male N-type connector for connecting to the antenna. It has a coveredEthernet port and utility port (for alignment headset, sync cable to CMM2, or override plug), the same as2.4, 5.2, and 5.7 GHz modules.Connectorized Subscriber Flat Panel AntennaMotorola offers an external subscriber antenna, as shown in Figure 3: Subscriber 900 MHz Flat PanelAntenna. The attributes of this antenna include:• 10 dBi gain• 8.8” x 8.1” x 1.6” (22.4 x 20.6 x 4.06 cm)• 1.2 lbs (0.54 kg)• vertical or horizontal polarization• 12 inch (30.5 cm) cable• female N-type connector• 3 dB beam width approximately 60° vertical and 60° horizontalFigure 3: Subscriber 900 MHz Flat Panel AntennaOther Connectorized Flat Panel AntennasMotorola has certified an additional two antennas that are available through Canopy resellers. Third partiesmay also certify additional antennas for use with the Canopy connectorized 900 MHz module.
Canopy 900 MHz AP and SM User GuideIssue 1, Draft 1 June, 2004 Page 12 of 16The attributes of one of these certified antennas (shown in Figure 4: Additional 900 MHz Flat PanelAntenna) is as follows:• 10 dBi gain• 12"x12"x1" (305x305x25 mm)• 3.3 lbs (1.5 kg)• vertical or horizontal polarization• female N-type connector)• 3 dB beam width 60° vertical and 60° horizontalFigure 4: Additional 900 MHz Flat Panel AntennaOperationImportant! Use of connectorized antennas requires professional installation. The professional installeris responsible for• Selection of an antenna approved for use with the Canopy 900 MHz AP and SM by the nationalregulatory agency• Setting of the gain consistent with the antenna and within regulatory limits• Use of moisture sealant to increase long-term reliability of the connectorized connectionEnter the dBi gain of your antenna in the Antenna Gain parameter on the AP Configuration page, as shownin Figure 2: Highlights of 900 MHz AP Configuration Page.For this antenna:Enter this Antenna Gain:900 MHz Flat Panel antenna available throughMotorola10 dBiAdditional Flat Panel antennas certified withregulatory agency by Motorola10 dBiAntenna certified by third partyConsult antenna documentation
Canopy 900 MHz AP and SM User GuideIssue 1, Draft 1 June, 2004 Page 13 of 16Leave the External Filters Delay parameter on the AP Configuration page (see Figure 2: Highlights of 900MHz AP Configuration Page at the factory default of 0 Nanoseconds, regardless of whether you have filtersinstalled. (The External Filter Delay was included in the user interface in case it was needed, but turns outto never be needed – leave it set to 0.)Important! To remain within the legal regulatory limits for antenna output power, you must not set theAntenna Gain parameter lower than the actual gain of your antenna. If you have a 10 dBi antenna, do notenter an Antenna Gain of 8 or 9. This parameter must be set equal to or higher than the actual gain of yourantenna to remain within the legal regulatory limits for antenna output power.The parameter has a range from 8 dBi to 32 dBi. When set to 8 dBi, the radio will have a power-out of 28dBm to generate the legal maximum EIRP of 36 dBm (4 W). When set to 32 dBi, the radio will have apower-out of 4 dBm to again generate the legal maximum EIRP of 36 dBm (4 W).Note! In some circumstances, it may be advantageous to set the parameter higher than the actual gain ofyour antenna. This reduces the power (and range) of the link, and may be useful to control RF emissionsand reduce multi-pathing and jitter in some situations.Important! When using connectorized antennas, the connector can be a point of failure over time dueto water egress. Accepted industry practices should be used to apply sealant and wrap the connector toprevent water egress.The male and female N-type connectors form a gas tight seal with each other, but the point where the cableenters each connector can be a point for water egress, with eventual corrosion and failure of the connection.Sealing and wrapping is critical to long-term reliability of the connection.2.7 Spectrum AnalyzerDescriptionThe Canopy 900 MHz SM provides a spectrum analyzer much like 2.4, 5.2, and 5.7 GHz SMs, as shown inFigure 5: 900 MHz SM Spectrum Analyzer. Due to the heavy general use of the 900 MHz spectrum, it isadvisable to use the SM’s built-in spectrum analyzer or other equipment to confirm the RF environmentboth at AP and at SM locations during site surveys.OperationOn the SM, click on Expanded Stats, then on Spectrum Analyzer. Click Enable several times to scan andcollect data, then click Disable to return the SM to normal mode.
Canopy 900 MHz AP and SM User GuideIssue 1, Draft 1 June, 2004 Page 14 of 16Figure 5: 900 MHz SM Spectrum Analyzer2.8 Remote AP without TowerDescriptionA 900 MHz AP can be collocated with a 2.4, 5.2, or 5.7 GHz SM to provide a “remote AP” solution andprovide coverage to a cluster of further distant subscribers, or subscribers with foliage, with no towerlocation or backhaul needed at the remote AP site. The 2.4, 5.2, or 5.7 GHz SM has to have clear LOS to itsAP, but it can be located near the ground and collocated with a 900 MHz AP that then communicates withNLOS 900 MHz SMs. NLOS range is dependent on foliage, topography, obstructions, and other RFengineering considerations.2.9 900 MHz Modules Use Release 4.2.2DescriptionCanopy 900 MHz APs and SMs require Canopy Software Release 4.2.2 or later, FPGA Version 051804 orlater (for DES modules), and Canopy Boot 3.0 or later. Release 4.2.2 will not be released for use with 2.4,5.2, and 5.7 GHz modules. 900 MHz modules running on Release 4.2.2 are fully compatible with mixednetworks containing other frequency band modules running on older releases.
Canopy 900 MHz AP and SM User GuideIssue 1, Draft 1 June, 2004 Page 15 of 163 900 MHz AP and SM SpecificationsSpecificationCanopy System RangeFrequency Band Ranges902 to 928 MHz (ISM)Access MethodTDD/TDMASignaling Rate3.3 MbpsModulation TypeHigh-index 2-level FSK (Frequency Shift Keying)(Optimized for interference rejection)Carrier to Interference (C/I)Less than 3 dB nominalReceiver Sensitivity-90 dBm at 10-4 BEROperating RangeUp to 40 miles (64 km) Line-of SightSignificant foliage penetration Non Line-of-SightTransmitter PowerUp to 1 W (30 dBm)Subscriber Flat PanelAntenna10 dBi gain.Vertically or horizontally polarized (changed by physical position),approximately 60° horizontal x 60° vertical 3 dB beam width.DC Power (measured at DCconverter)For both AP and SM: Typically 0.3 A @ 24 VDC (7.2 watts)For AP: May reach 0.35 A @ 24 VDC (8.4 watts) under heavy load(high transmit ratio (set by downlink percentage), high packetthroughput)Ethernet, GPS sync, and GPScoax cablesThe use of cables that are rated for the operation temperature of theproduct and that conform to UV light protection specifications ismandatory. The use of shielded cables is strongly recommended,especially on infrastructure (APs).Interface10/100BaseT, half/full duplex.Rate auto-negotiated (802.3 compliant).Protocols UsedIPv4, UDP, TCP, ICMP, Telnet, HTTP, FTP, SNMP, DES.Optionally, AES.Protocols SupportedSwitched Layer 2 Transport with support for all common Ethernetprotocols, such as IPv6, NetBIOS, DHCP, IPX.Software Upgrade PathRemotely downloaded into flash memoryNetwork ManagementHTTP, telnet, FTP, SNMPWind118 miles/hour (190 km/hour)Operation Temperature-40° F to +131º F (-40° C to +55° C)Connectorized ModuleWeight: 1 lb (0.45 kg)Dimensions: 11.75” H x 3.4” W x 3.4” D (29.9 cm H x 8.6 cm W x 8.6cm D)
Canopy 900 MHz AP and SM User GuideIssue 1, Draft 1 June, 2004 Page 16 of 16SpecificationCanopy System Rangecm D)

Navigation menu