Motorola Solutions 89FT3833 Portable 2-Way Radio User Manual MOTOTRBO User Guide

Motorola Solutions, Inc. Portable 2-Way Radio MOTOTRBO User Guide

Contents

Manual

Download: Motorola Solutions 89FT3833 Portable 2-Way Radio User Manual MOTOTRBO User Guide
Mirror Download [FCC.gov]Motorola Solutions 89FT3833 Portable 2-Way Radio User Manual MOTOTRBO User Guide
Document ID1980207
Application IDi54L05PNAOFPXuA5MPFoiA==
Document DescriptionManual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize366.36kB (4579459 bits)
Date Submitted2013-05-31 00:00:00
Date Available2013-05-31 00:00:00
Creation Date2013-03-12 14:47:44
Producing SoftwareAcrobat Distiller 7.0 (Windows)
Document Lastmod2013-03-12 15:53:19
Document TitleMOTOTRBO User Guide
Document CreatorFrameMaker 8.0
Document Author: Motorola Solutions, Inc.

NAG-LACR.book Page i Tuesday, March 12, 2013 3:37 PM
MOTOTRBO XPRTM 7150
Non-Display Portable
User Guide
68009677001-A
NAG-LACR.book Page ii Tuesday, March 12, 2013 3:37 PM
NAG-LACR.book Page i Tuesday, March 12, 2013 3:37 PM
Declaration of Conformity
DECLARATION OF CONFORMITY
Per FCC CFR 47 Part 2 Section 2.1077(a)
Responsible Party
Name: Motorola Solutions, Inc.
Address: 1303 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A.
Phone Number: 1-800-927-2744
Hereby declares that the product:
Model Name: XPR 7150
conforms to the following regulations:
Declaration of Conformity
This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below.
FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a)
Class B Digital Device
As a personal computer peripheral, this device complies with Part 15 of the FCC Rules. This device complies with Industry
Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
English
NAG-LACR.book Page ii Tuesday, March 12, 2013 3:37 PM
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
Declaration of Conformity
• Increase the separation between the equipment and receiver.
ii
English
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NAG-LACR.book Page iii Tuesday, March 12, 2013 3:37 PM
Contents
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . i
Important Safety Information . . . . . . . . . . . . . . . . . vi
Product Safety and RF Exposure Compliance . . .vi
Firmware Version . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
Contents
This User Guide contains all the information you need to
use the MOTOTRBO XPR 7150 Digital Portable Radio.
Identifying Radio Controls . . . . . . . . . . . . . . . . . . . . 6
Radio Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Programmable Buttons . . . . . . . . . . . . . . . . . . . . . . . 8
Assignable Radio Functions . . . . . . . . . . . . . . . . . 8
Assignable Settings or Utility Functions . . . . . . . . . 9
Push-To-Talk (PTT) Button . . . . . . . . . . . . . . . . . . . . 9
Switching Between Conventional Analog and Digital
Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
IP Site Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Capacity Plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Linked Capacity Plus . . . . . . . . . . . . . . . . . . . . . . . 12
Computer Software Copyrights . . . . . . . . . . . . . . . vii
Handling Precautions . . . . . . . . . . . . . . . . . . . . . . viii
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . . 1
What Your Dealer/System Administrator
Can Tell You . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Preparing Your Radio for Use . . . . . . . . . . . . . . . . . . 2
Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . 2
Attaching the Battery . . . . . . . . . . . . . . . . . . . . . . . . . 3
Attaching the Antenna . . . . . . . . . . . . . . . . . . . . . . . . 3
Attaching the Universal Connector Cover (Dust Cover)
Attaching the Accessory Connector . . . . . . . . . . . . . 4
Powering Up the Radio . . . . . . . . . . . . . . . . . . . . . . . 5
Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . 5
Identifying Status Indicators . . . . . . . . . . . . . . . . . . 15
LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Audio Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Indicator Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Receiving and Making Calls . . . . . . . . . . . . . . . . . . 18
Selecting a Channel . . . . . . . . . . . . . . . . . . . . . . . . 18
Receiving and Responding to a Radio Call . . . . . . 19
Receiving and Responding to a Group Call . . . . . 19
Receiving and Responding to a Private Call . . . 20
Receiving an All Call . . . . . . . . . . . . . . . . . . . . . . 21
Receiving and Responding to a Phone Call . . . . 22
Phone Call as a Private Call or Group Call . . . 22
Phone Call as an All Call . . . . . . . . . . . . . . . . . 22
iii
English
NAG-LACR.book Page iv Tuesday, March 12, 2013 3:37 PM
Contents
Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . 23
Making a Call with the Channel Selector Knob . . 23
Making a Group Call . . . . . . . . . . . . . . . . . . . . 23
Making a Private Call . . . . . . . . . . . . . . . . . . . 24
Making a Selective Call . . . . . . . . . . . . . . . . . . . 25
Making an All Call . . . . . . . . . . . . . . . . . . . . . . 25
Making a Phone Call with the Programmable Phone
Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Stopping a Radio Call . . . . . . . . . . . . . . . . . . . . . . 26
Talkaround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Monitoring Features . . . . . . . . . . . . . . . . . . . . . . . . 27
Monitoring a Channel . . . . . . . . . . . . . . . . . . . . . 27
Permanent Monitor . . . . . . . . . . . . . . . . . . . . . . . 28
iv
Advanced Features . . . . . . . . . . . . . . . . . . . . . . . . .
Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting and Stopping Scan . . . . . . . . . . . . . . . .
Responding to a Transmission During a Scan . .
Deleting a Nuisance Channel . . . . . . . . . . . . . . .
Restoring a Nuisance Channel . . . . . . . . . . . . . .
Vote Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Indicator Settings . . . . . . . . . . . . . . . . . . . . . .
Escalating Alarm Tone Volume . . . . . . . . . . . . . .
Call Alert Operation . . . . . . . . . . . . . . . . . . . . . . . .
Receiving and Responding to a Call Alert . . . . .
English
Making a Call Alert with the One Touch Access Button
32
Emergency Operation . . . . . . . . . . . . . . . . . . . . . . 33
Sending an Emergency Alarm . . . . . . . . . . . . . . 33
Sending an Emergency Alarm with Call . . . . . . . 34
Sending an Emergency Alarm with Voice to
Follow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Reinitiating an Emergency Mode . . . . . . . . . . . . 36
Exiting an Emergency Mode . . . . . . . . . . . . . . . . 36
Privacy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Multi-Site Controls . . . . . . . . . . . . . . . . . . . . . . . . . 37
Starting an Automatic Site Search . . . . . . . . . . . 37
Stopping an Automatic Site Search . . . . . . . . . . 37
Starting a Manual Site Search . . . . . . . . . . . . . . 38
Lone Worker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Password Lock Features . . . . . . . . . . . . . . . . . . . . 38
Accessing the Radio from Password . . . . . . . . . 38
Unlocking the Radio from Locked State . . . . . . . 39
Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Finding and Connecting to a Bluetooth Device . . 40
Disconnecting from a Bluetooth Device . . . . . . . 41
Switching Audio Route . . . . . . . . . . . . . . . . . . . . 41
Auto-Range Transponder System (ARTS) . . . . . . . 41
Over-the-Air Programming (OTAP) . . . . . . . . . . . . 42
Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
29
29
30
30
30
31
31
31
32
32
32
32
NAG-LACR.book Page v Tuesday, March 12, 2013 3:37 PM
Operating Frequency Requirements . . . . . . . . . . . . 50
Declaration of Compliance for the Use of Distress and
Safety Frequencies . . . . . . . . . . . . . . . . . . . . . . . . 52
Technical Parameters for Interfacing External Data
Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Batteries and Chargers Warranty . . . . . . . . . . . . . . 53
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Contents
Setting the Squelch Level . . . . . . . . . . . . . . . . . . 42
Setting the Power Level . . . . . . . . . . . . . . . . . . . . 42
Turning the Voice Operating Transmission (VOX)
Feature On or Off . . . . . . . . . . . . . . . . . . . . . . . . . 43
Turning the Howling Suppressor Feature On or Off
43
Turning Radio Tones/Alerts On or Off . . . . . . . . . 43
Checking the Battery Strength . . . . . . . . . . . . . . . 44
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Carry Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Chargers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Earbuds and Earpieces . . . . . . . . . . . . . . . . . . . . . . 46
Headsets and Headset Accessories . . . . . . . . . . . . 47
Remote Speaker s . . . . . . . . . . . . . . . . . . . . . . . . . 47
Surveillance Accessories . . . . . . . . . . . . . . . . . . . . 48
Miscellaneous Accessories . . . . . . . . . . . . . . . . . . . 48
Appendix: Maritime Radio Use in the VHF Frequency
Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Special Channel Assignments . . . . . . . . . . . . . . . . 49
Emergency Channel . . . . . . . . . . . . . . . . . . . . . . 49
Non-Commercial Call Channel . . . . . . . . . . . . . . 50
English
NAG-LACR.book Page vi Tuesday, March 12, 2013 3:37 PM
Any modification to this device, not expressly authorized by
Motorola, may void the user’s authority to operate this device.
Important Safety Information
Product Safety and RF Exposure Compliance
Important Safety Information
Before using this product, read the operating
instructions for safe usage contained in the
Product Safety and RF Exposure booklet
enclosed with your radio.
ATTENTION!
This radio is restricted to occupational use only to
satisfy FCC RF energy exposure requirements.
Before using this product, read the RF energy awareness
information and operating instructions in the XPR 7150
SeriesPortable Radio Regulatory Compliance and
Product Safety / Quick Reference Guide (Motorola
Publication part number 68009511001) to ensure
compliance with RF energy exposure limits.
For a list of Motorola-approved antennas, batteries, and
other accessories, visit the following website:
http://www.motorolasolutions.com
vi
English
Under Industry Canada regulations, this radio transmitter may
only operate using an antenna of a type and maximum (or
lesser) gain approved for the transmitter by Industry Canada. To
reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
This radio transmitter has been approved by Industry Canada to
operate with Motorola-approved antenna with the maximum
permissible gain and required antenna impedance for each
antenna type indicated. Antenna types not included in this list,
having a gain greater than the maximum gain indicated for that
type, are strictly prohibited for use with this device.
Firmware Version
All the features described in the following sections are
supported by the radio's software version R02.06.10.
Check with your dealer or system administrator for more
details for all the features supported.
NAG-LACR.book Page vii Tuesday, March 12, 2013 3:37 PM
Computer Software Copyrights
This voice coding Technology is licensed solely for use
within this Communications Equipment. The user of this
Technology is explicitly prohibited from attempting to
decompile, reverse engineer, or disassemble the Object
Code, or in any other way convert the Object Code into a
human-readable form.
U.S. Pat. Nos. #5,870,405, #5,826,222, #5,754,974,
#5,701,390, #5,715,365, #5,649,050, #5,630,011,
#5,581,656, #5,517,511, #5,491,772, #5,247,579,
#5,226,084 and #5,195,166.
Computer Software Copyrights
The Motorola products described in this manual may
include copyrighted Motorola computer programs stored
in semiconductor memories or other media. Laws in the
United States and other countries preserve for Motorola
certain exclusive rights for copyrighted computer
programs including, but not limited to, the exclusive right
to copy or reproduce in any form the copyrighted
computer program. Accordingly, any copyrighted
Motorola computer programs contained in the Motorola
products described in this manual may not be copied,
reproduced, modified, reverse-engineered, or distributed
in any manner without the express written permission of
Motorola. Furthermore, the purchase of Motorola
products shall not be deemed to grant either directly or by
implication, estoppel, or otherwise, any license under the
copyrights, patents or patent applications of Motorola,
except for the normal non-exclusive license to use that
arises by operation of law in the sale of a product.
The AMBE+2TM voice coding Technology embodied in
this product is protected by intellectual property rights
including patent rights, copyrights and trade secrets of
Digital Voice Systems, Inc.
vii
English
NAG-LACR.book Page viii Tuesday, March 12, 2013 3:37 PM
maximum limit or use without antenna may result in damage
to the radio.
Handling Precautions
The MOTOTRBO XPR 3300 Portable Radio meets IP55
specifications with antenna attached, allowing the radio to
withstand adverse field conditions such as being used in rain or
dusty environment.
• If the radio has been exposed to water or rain, shake the
Handling Precautions
radio well to remove any water that may be trapped inside the
speaker grille, port and aesthetic cover (if applicable).
Trapped water in speaker grille and port could cause
decreased audio performance. If aesthetic cover is attached
onto radio, trapped water in aesthetic cover could cause
corrosion on the slim connector interface gold contacts.
viii
• When cleaning the radio, do not use a high pressure jet spray
on the radio as this may cause to leak.
Do not disassemble the radio. This could
damage radio seals and result in leak paths into
the radio. Radio maintenance should only be
done in service depot that is equipped to test
and replace the seal on the radio.
• If the radio’s battery contact area has been exposed to water,
clean and dry battery contacts on both the radio and the
battery before attaching the battery to the radio. The residual
water could short-circuit the radio.
• If the radio has been exposed to corrosive substance
(e.g.saltwater), rinse the radio and battery in fresh water then
dry the radio and battery.
• To clean the exterior surfaces of the radio, use a diluted
solution of mild dishwashing detergent and fresh water (i.e.
one teaspoon of detergent to one gallon of water).
• The radio with antenna attached properly is designed to be
protected against dust and low pressure jets of water
projected with nozzle 6.3mm diameter at flow rate of
12.5 l/min, with water pressure at 30 kN/m2 and from a
distance of 2.5m to 3m for at least 3 min. Exceeding either
English
NAG-LACR.book Page 1 Tuesday, March 12, 2013 3:37 PM
For features that are available in a conventional multi-site
mode, see IP Site Connect on page 10 for more information.
Getting Started
How to Use This Guide
Selected features are also available on the single-site trunking
mode, Capacity Plus. See Capacity Plus on page 12 for more
information.
Selected features are also available in the multi-site trunking
mode, Linked Capacity Plus. See Linked Capacity Plus on
page 12 for more information.
This User Guide covers the basic operation of the MOTOTRBO
Non-Display Portables.
However, your dealer or system administrator may have
customized your radio for your specific needs. Check with your
dealer or system administrator for more information.
Throughout this publication, the icons below are used to
indicate features supported in either the conventional Analog
mode or conventional Digital mode:
Indicates a conventional Analog Mode-Only feature.
What Your Dealer/System Administrator
Can Tell You
Getting Started
Take a moment to review the following:
How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . . . . page 1
What Your Dealer/System Administrator
Can Tell You. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1
You can consult your dealer or system administrator about the
following:
• Is your radio programmed with any preset conventional
channels?
• Which buttons have been programmed to access other
features?
• What optional accessories may suit your needs?
• What are the best radio usage practices for effective
Indicates a conventional Digital Mode-Only feature.
communication?
• What maintenance procedures will help promote longer radio
For features that are available in both Analog and Digital
modes, no icon is shown.
life?
English
NAG-LACR.book Page 2 Tuesday, March 12, 2013 3:37 PM
Charging the Battery
Preparing Your Radio for Use
Preparing Your Radio for Use
Assemble your radio by following these steps:
Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attaching the Battery. . . . . . . . . . . . . . . . . . . . . . . . . . .
Attaching the Antenna. . . . . . . . . . . . . . . . . . . . . . . . . .
Attaching the Universal Connector
Cover (Dust Cover) . . . . . . . . . . . . . . . . . . . . . . . . . .
Attaching the Accessory Connector . . . . . . . . . . . . . . .
Powering Up the Radio . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . .
English
page 2
page 3
page 3
page 4
page 4
page 5
page 5
Your radio is powered by a Lithium-Ion (Li-lon) battery. To avoid
damage and comply with warranty terms, charge the battery
using a Motorola charger exactly as described in the charger
user guide. It is recommended your radio remains powered off
while charging.
Charge a new battery 14 to 16 hours before initial use for best
performance.
IMPORTANT: ALWAYS charge your IMPRES battery with an
IMPRES charger for optimized battery life and
valuable battery data. IMPRES batteries
charged exclusively with IMPRES chargers
receive a 6-month capacity warranty extension
over the standard Motorola Premium battery
warranty duration.
NAG-LACR.book Page 3 Tuesday, March 12, 2013 3:37 PM
Attaching the Battery
Attaching the Antenna
With the radio turned off, set the
antenna in its receptacle and turn
clockwise.
To remove the antenna, turn the
antenna counterclockwise.
If antenna needs to be replaced, ensure that only
MOTOTRBO antennas are used. Neglecting this will
damage your radio. See Antennas on page 45 for a
list of available antennas.
Preparing Your Radio for Use
Align the battery with the rails on the back of the radio. Fit the
battery to the contacts and push the top of the battery down until
the latch snaps into place.
To remove the battery, turn the
radio off. Move the battery latch
into unlock position and hold.
Battery
Latch
English
NAG-LACR.book Page 4 Tuesday, March 12, 2013 3:37 PM
Attaching the Universal Connector Cover
(Dust Cover)
The universal connector is located on the antenna side of the
radio. It is used to connect MOTOTRBO accessories to the
radio.
Preparing Your Radio for Use
1 Insert the slanted end of
the cover into the slots
above the universal
connector.
Press downwards on the
cover to seat the dust
cover properly on the
Universal Connector.
Secure the dust cover to
the radio by pushing the
latch upwards.
To remove the dust cover,
push the latch downwards.
Lift the cover up and slide
down the dust cover from
the universal connector to
remove it.
Replace the dust cover
when the universal
connector is not in use.
English
Attaching the Accessory Connector
The accessory connector is
to be secured to the
universal connector on the
antenna side of he radio.
To attach the accessory
connector, refer to the steps
shown in the diagram.
To remove the accessory
connector, refer to the steps
shown in the diagram.
NAG-LACR.book Page 5 Tuesday, March 12, 2013 3:37 PM
Powering Up the Radio
Adjusting the Volume
A brief tone sounds,
indicating that the power up
test is successful.There is no
power up tone if the radio
tones/alerts function is
disabled (see Turning Radio
Tones/Alerts On or Off on
page 43).
To increase the volume, turn the On/Off/Volume Control Knob
clockwise.
If your radio does not power
up, check your battery. Make
sure that it is charged and properly attached. If your radio still
does not power up, contact your dealer.
To decrease the volume, turn this knob counterclockwise.
Note:
To turn off the radio, rotate this knob counterclockwise until you
hear a click.
Your radio can be programmed to have a minimum
volume offset where the volume level cannot be turned
down fully. Check with your dealer or system
administrator for more information.
Preparing Your Radio for Use
Rotate the On/Off/Volume
Control Knob clockwise until
you hear a click. The LED
lights up solid green.
English
NAG-LACR.book Page 6 Tuesday, March 12, 2013 3:37 PM
Identifying Radio Controls
Identifying Radio Controls
Take a moment to review the following:
Radio Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7
Programmable Buttons . . . . . . . . . . . . . . . . . . . . . . . . . page 8
Push-To-Talk (PTT) Button . . . . . . . . . . . . . . . . . . . . . . page 9
Switching Between Conventional Analog and
Digital Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 10
IP Site Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 10
Capacity Plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 12
Linked Capacity Plus. . . . . . . . . . . . . . . . . . . . . . . . . . page 12
English
NAG-LACR.book Page 7 Tuesday, March 12, 2013 3:37 PM
Radio Controls
5 Side Button 1*
11
10
6 Side Button 2*
9 Universal Connector for Accessories
8 Speaker
10 Emergency Button
11 Antenna
* These buttons are programmable
Identifying Radio Controls
1 Channel Selector Knob
2 On/Off/Volume Control Knob
3 LED Indicator
4 Push-to-Talk (PTT) Button
English
NAG-LACR.book Page 8 Tuesday, March 12, 2013 3:37 PM
Bluetooth Discoverable – Enables your radio to enter
Bluetooth Discoverable Mode.
Programmable Buttons
Your dealer can program the programmable buttons as
shortcuts to radio functions or preset channels/groups
depending on the duration of a button press:
• Short press – Pressing and releasing rapidly.
• Long press – Pressing and holding for the programmed
duration.
Identifying Radio Controls
• Hold down – Keeping the button pressed.
®
Bluetooth Audio Switch – Toggles audio routing between
internal radio speaker and external Bluetooth-enabled
accessory.
Bluetooth Connect – Initiates a Bluetooth find-and-connect
operation.
Bluetooth Disconnect – Terminates all existing Bluetooth
connections between your radio and any Bluetooth-enabled
devices.
English
Voice Announcement for Channel – Plays zone and channel
announcement voice messages for the current channel. This
function is unavailable when Voice Announcement is disabled.
Emergency – Depending on the programming, initiates or
cancels an emergency alarm or call.
NOTE: The programmed duration of a button press is
applicable for all assignable radio/utility functions or
settings. See Emergency Operation on page 33 for
more information on the programmed duration of the
Emergency button.
 Assignable Radio Functions
Call Forwarding – Toggles Call Forwarding on or off.
Intelligent Audio On/Off – Toggles Intelligent Audio on or off.
Manual Site Roam*‡
– Starts the manual site search.
Mic AGC On/Off – Toggles the internal automatic gain control
(AGC) on or off. Not applicable during a Bluetooth session.
Monitor – Monitors a selected channel for activity.
Nuisance Channel Delete*‡ – Temporarily removes an
unwanted channel, except for the Selected Channel, from the
scan list. The Selected Channel refers to the user’s selected
zone/channel combination from which scan is initiated.
Notifications – Provides direct access to the Notifications List.
One Touch Access
– Directly initiates a predefined
Private or Group Call, a Call Alert.
‡ Not
* Not applicable in Capacity Plus
applicable in Linked Capacity Plus
NAG-LACR.book Page 9 Tuesday, March 12, 2013 3:37 PM
 Assignable Settings or Utility Functions
Privacy
Repeater/Talkaround*‡
Power Level – Toggles transmit power level between high and
low.
Scan* – Toggles scan on or off.
Squelch
normal.
– Toggles privacy on or off.
– Toggles between using a repeater
and communicating directly with another radio.
Site Lock On/Off*‡
All Tones/Alerts – Toggles all tones and alerts on or off.
– Toggles squelch level between tight and
– Toggles the automatic site roam on
Push-To-Talk (PTT) Button
or off.
Transmit Interrupt Remote Dekey
– Stops an ongoing
interruptible call to free the channel. (A Software License Key
sold separately is required to use this feature).
The PTT button on the
side of the radio serves
two basic purposes:
Voice Announcement On/Off – Toggles Voice Announcement
on or off.
• While a call is in
Voice Operating Transmission (VOX) – Toggles VOX on or
off.
Zone – Allows selection from only one zone.
Battery Strength – Indicates battery strength via the LED
Indicator.
progress, the PTT
button allows the radio
to transmit to other
radios in the call.
PTT
Button
Identifying Radio Controls
Permanent Monitor*‡– Monitors a selected channel for all
radio traffic until function is disabled.
Press and hold down
PTT button to talk.
Release the PTT
button to listen.
The is
activated when the PTT button is pressed.
‡ Not
* Not applicable in Capacity Plus
applicable in Linked Capacity Plus
English
NAG-LACR.book Page 10 Tuesday, March 12, 2013 3:37 PM
• While a call is not in progress, the PTT button is used to make
a new call (see Making a Radio Call on page 23).
Depending on programming, if the Talk Permit Tone or the PTT
Identifying Radio Controls
Sidetone
is enabled, wait until the short alert tone ends
before talking.
10
English
During a call, if the Channel Free Indication feature is
enabled on your radio (programmed by your dealer), you
will hear a short alert tone the moment the target radio (the
radio that is receiving your call) releases the PTT button,
indicating the channel is free for you to respond.
Switching Between Conventional Analog and
Digital Mode
Each channel in your radio
can be configured as a
conventional analog or
conventional digital channel.
Use the Channel Selector
Knob to switch between an
analog or a digital channel.
Channel Selector Knob
You will also hear a continuous talk prohibit tone, if your
call is interrupted, indicating that you should release the
PTT button, for example when the radio receives an
Emergency Call.
When switching from digital
to analog mode, certain
features are unavailable.
Your radio also has features available in both analog and digital
mode. However, the minor differences in the way each feature
works does NOT affect the performance of your radio.
NOTE: Your radio also switches between digital and analog
modes during a dual mode scan (see Scan on
page 30).
IP Site Connect
This feature allows your radio to extend conventional
communication beyond the reach of a single site, by connecting
to different available sites which are connected via an Internet
Protocol (IP) network.
NAG-LACR.book Page 11 Tuesday, March 12, 2013 3:37 PM
NOTE: This feature is not applicable in Capacity Plus.
If the radio is set to do this automatically, it scans through all
available sites when the signal from the current site is weak or
when the radio is unable to detect any signal from the current
site. It then locks on to the repeater with the strongest Received
Signal Strength Indicator (RSSI) value.
In a manual site search, the radio searches for the next site in
the roam list that is currently in range (but which may not have
the strongest signal) and locks on to it.
NOTE: Each channel can only have either Scan or Roam
enabled, not both at the same time.
Channels with this feature enabled can be added to a particular
roam list. The radio searches the channel(s) in the Members
roam list during the automatic roam operation to locate the best
site.
Identifying Radio Controls
When the radio moves out of range from one site and into the
range of another, it connects to the new site's repeater to send
or receive calls/data transmissions. Depending on your settings,
this is done automatically or manually.
Check with your dealer or system administrator for more
information.
A Members roam list supports a maximum of 16 channels
(including the Selected Channel).
You cannot manually add or delete an entry to the Members
roam list. A Software License Key sold separately is required to
use this feature.
11
English
NAG-LACR.book Page 12 Tuesday, March 12, 2013 3:37 PM
Capacity Plus
Linked Capacity Plus
Capacity Plus is a single-site trunking configuration of the
MOTOTRBO radio system, which uses a pool of channels to
support hundreds of users and up to 254 Groups. This feature
allows your radio to efficiently utilize the available number of
programmed channels while in Repeater Mode.
Identifying Radio Controls
You can only access channel(s) with Capacity Plus via the
Channel Selector Knob, while features supported in Capacity
Plus can be accessed via a programmable button press.
Your radio also has features that are available in both
conventional digital mode and Capacity Plus. However, the
minor differences in the way each feature works does NOT
affect the performance of your radio.A Software License Key
sold separately is required to use this feature.
Check with your dealer or system administrator for more
information on this system.
English
Linked Capacity Plus allows your radio to extend trunking
communication beyond the reach of a single site, by connecting
to different available sites which are connected via an Internet
Protocol (IP) network. It also provides an increase in capacity by
efficiently utilizing the combined available number of
programmed channels supported by each of the available sites.
You will hear a negative indicator tone if you access a feature
not applicable to Capacity Plus via a programmable button
press.
12
Linked Capacity Plus is a multi-site multi-channel trunking
configuration of the MOTOTRBO radio system, combining the
best of both Capacity Plus and IP Site Connect configurations.
When the radio moves out of range from one site and into the
range of another, it connects to the new site's repeater to send
or receive calls/data transmissions. Depending on your settings,
this is done automatically or manually.
If the radio is set to do this automatically, it scans through all
available sites when the signal from the current site is weak or
when the radio is unable to detect any signal from the current
site. It then locks on to the repeater with the strongest Received
Signal Strength Indicator (RSSI) value.
In a manual site search, the radio searches for the next site in
the roam list that is currently in range (but which may not have
the strongest signal) and locks on to it.
Any channel with Linked Capacity Plus enabled can be added
to a particular roam list. The radio searches these channels
during the automatic roam operation to locate the best site.
NAG-LACR.book Page 13 Tuesday, March 12, 2013 3:37 PM
Similar to Capacity Plus, icons of features not applicable to
Linked Capacity Plus are not available in the menu. You hear a
negative indicator tone if you try to access a feature not
applicable to Linked Capacity Plus via a programmable button
press. A Software License Key sold separately is required to
use this feature
Check with your dealer or system administrator for more
information on this configuration.
Identifying Radio Controls
NOTE: You cannot manually add or delete an entry to the roam
list. Check with your dealer or system administrator for
more information.
13
English
Identifying Radio Controls
NAG-LACR.book Page 14 Tuesday, March 12, 2013 3:37 PM
14
English
NAG-LACR.book Page 15 Tuesday, March 12, 2013 3:37 PM
LED Indicator
Identifying Status Indicators
The LED indicator shows the
operational status of your radio.
Blinking red – Radio is
transmitting at low battery
condition, receiving an
emergency transmission or has
failed the self-test upon
powering up, or has moved out
of range if radio is configured
with Auto-Range Transponder
System.
LED
Indicator
Solid yellow – Radio is
monitoring a conventional
channel or in Bluetooth Discoverable Mode. Also indicates fair
battery charge when Battery Strength button is pressed.
Identifying Status Indicators
Your radio indicates its operational status through the following:
LED Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 15
Audio Tones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 16
Indicator Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 17
Blinking yellow – Radio is scanning for activity or receiving a
Call Alert, or all local Linked Capacity Plus channels are busy.
Rapidly blinking yellow – Radio is actively searching for a new
site.
15
English
NAG-LACR.book Page 16 Tuesday, March 12, 2013 3:37 PM
Double blinking yellow – Radio is no longer connected to the
repeater while in Capacity Plus or Linked Capacity Plus, all
Capacity Plus channels and Linked Capacity Plus channels are
currently busy, Auto Roaming is enabled, radio is actively
searching for a new site. Also indicates radio has yet to respond
to a group call alert, or radio is locked.
Identifying Status Indicators
Solid green – Radio is powering up, or transmitting. Also
indicates full charge of the battery when Battery Strength button
is pressed.
Double blinking green – Radio is receiving a privacy-enabled
NOTE: While in conventional mode, when the LED blinks
green, it indicates the radio detects activity over the air.
Due to the nature of the digital protocol, this activity
may or may not affect the radio's programmed
channel.
16
English
Alert tones provide you with audible indications of the radio’s
status or the radio’s response to data received.
Continuous Tone A monotone sound. Sounds
continuously until termination.
Periodic Tone
Blinking green – Radio is receiving a non-privacy-enabled call
or data, detecting activity or retrieving Over-the-Air
Programming transmissions over the air.
call or data.
Audio Tones
For Capacity Plus and Linked Capacity Plus, there is
no LED indication when the radio is detecting activity
over the air.
Repetitive Tone
Sounds periodically depending on the
duration set by the radio. Tone starts,
stops, and repeats itself.
A single tone that repeats itself until it is
terminated by the user.
Momentary Tone Sounds only once for a short period of
time defined by the radio.
NAG-LACR.book Page 17 Tuesday, March 12, 2013 3:37 PM
Indicator Tones
Low pitched tone
Positive Indicator Tone
Negative Indicator Tone
Identifying Status Indicators
High pitched tone
17
English
NAG-LACR.book Page 18 Tuesday, March 12, 2013 3:37 PM
Selecting a Channel
Receiving and Making Calls
Receiving and Making Calls
Once you understand how your MOTOTRBO Portable is
configured, you are ready to use your radio.
Use this navigation guide to familiarize yourself with the basic
Call features:
Selecting a Radio Channel, Subscriber ID,
or Group ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 18
Receiving and Responding to a Radio Call. . . . . . . . . page 19
Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . . . page 23
Stopping a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . . page 26
Talkaround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 27
Monitoring Features . . . . . . . . . . . . . . . . . . . . . . . . . . page 27
18
English
Transmissions are sent and received on a channel. Depending
on your radio’s configuration, each channel may have been
programmed differently to support different groups of users or
supplied with different features. After selecting the relevant
Zone, select the relevant channel you require to transmit or
receive on.
Procedure:
Once the required zone is set (if you have multiple zones in
your radio), turn the Channel Selector Knob to select the
number that represents the channel, subscriber ID, or group
ID.
NAG-LACR.book Page 19 Tuesday, March 12, 2013 3:37 PM
Receiving and Responding to a Radio Call
See Privacy on page 36 for more information.
 Receiving and Responding to a Group Call
To receive a call from a group of users, your radio must be
configured as part of that group.
LED Indicator
1 The LED blinks green. Your radio unmutes and the incoming
call sounds through the radio's speaker.
2 To respond, hold the radio vertically 1 to 2 inches
(2.5 to 5.0 cm) from your mouth.
The LED lights up solid green while the radio is transmitting and
blinks when the radio is receiving.
NOTE: The LED lights up solid green while the radio is
transmitting and double blinks green when the radio is
receiving a privacy-enabled call.
To unscramble a privacy-enabled call, your radio
must have the same Privacy Key, OR the same Key
Value and Key ID (programmed by your dealer) as
the transmitting radio (the radio you are receiving
the call from).
If the Channel Free Indication feature is enabled, you
will hear a short alert tone the moment the transmitting radio
releases the PTT button, indicating the channel is free for
you to respond.
Press the PTT button to respond to the call.
OR
Receiving and Making Calls
Once the channel, subscriber ID, or group ID is set, you can
proceed to receive and respond to calls.
If the Voice Interrupt feature is enabled, press the PTT
button to stop the current call from the transmitting radio and
free the channel for you to talk/respond.
4 The LED lights up solid green.
5 Wait for the Talk Permit Tone to finish (if enabled) and speak
clearly into the .
OR
19
English
NAG-LACR.book Page 20 Tuesday, March 12, 2013 3:37 PM
Wait for the PTT Sidetone to finish (if enabled) and
speak clearly into the .
6 Release the PTT button to listen.
4 Press the PTT button to respond to the call. The LED lights
7 If there is no voice activity for a predetermined period of
time, the call ends.
Receiving and Making Calls
20
up solid green.
5 Wait for the Talk Permit Tone to finish (if enabled) and speak
See Making a Group Call on page 23 for details on making a
Group Call.
 Receiving and Responding to a Private Call
If the Voice Interrupt feature is enabled, press the PTT
button to stop the current call from the transmitting radio and
free the channel for you to talk/respond.
clearly into the .
6 Release the PTT button to listen.
7 If there is no voice activity for a predetermined period of
time, the call ends.
A Private Call is a call from an individual radio to another
individual radio.
8 You hear a short tone.
Procedure:
See Making a Private Call on page 24 for details on making a
Private Call.
When you receive a private call:
1 The LED blinks green. Your radio unmutes and the incoming
call sounds through the radio's speaker.
2 To respond, hold the radio vertically 1 to 2 inches
(2.5 to 5.0 cm) from your mouth.
3 If the Channel Free Indication feature is enabled, you will
hear a short alert tone the moment the transmitting radio
releases the PTT button, indicating the channel is free for
you to respond.
Press the PTT button to respond to the call.
OR
English
NAG-LACR.book Page 21 Tuesday, March 12, 2013 3:37 PM
 Receiving and Responding to a Selective Call
Procedure:
When you receive a Selective Call:
1 The LED blinks green. Your radio unmutes and the incoming
call sounds through the radio's speaker.
3 If the Channel Free Indication feature is enabled, you will
hear a short alert tone the moment the transmitting radio
releases the PTT button, indicating the channel is free for
you to respond.
Press the PTT button to respond to the call.
4 Press the PTT button to respond to the call. The LED lights
up solid green.
5 Wait for the Talk Permit Tone to finish (if enabled) and speak
clearly into the .
6 Release the PTT button to listen.
7 If there is no voice activity for a predetermined period of
time, the call ends.
An All Call is a call from an individual radio to every radio on the
channel. It is used to make important announcements requiring
the user’s full attention.
Procedure:
When you receive an All Call:
2 To respond, hold the radio vertically 1 to 2 inches
(2.5 to 5.0 cm) from your mouth.
 Receiving an All Call
1 A tone sounds and the LED blinks green. Your radio
unmutes and the incoming call sounds through the radio's
speaker.
2 An All Call does not wait for a predetermined period of time
before ending.
If the Channel Free Indication feature is enabled, you
will hear a short alert tone the moment the transmitting radio
releases the PTT button, indicating the channel is now
available for use.
Receiving and Making Calls
A Selective Call is a call from an individual radio to another
individual radio. It is a Private Call on an analog system.
See Making a Selective Call on page 25 for details on making
a Selective Call.
You cannot respond to an All Call.
NOTE: The radio stops receiving the All Call if you switch to a
different channel while receiving the call.
During an All Call, you will not be able to use any
programmed button functions until the call ends.
8 You hear a short tone.
21
English
NAG-LACR.book Page 22 Tuesday, March 12, 2013 3:37 PM
 Receiving and Responding to a Phone Call
 Phone Call as an All Call
 Phone Call as a Private Call or Group Call
Procedure:
When you receive a Phone Call as an All Call:
Procedure:
When you receive a Phone Call as a Private Call or Group Call:
The LED blinks green. Your radio unmutes and the incoming
call sounds through the radio’s speaker.
1 The LED blinks green. Your radio unmutes and the incoming
An All Call does not wait for a predetermined period of time
before ending.
Receiving and Making Calls
call sounds through the radio’s speaker.
2 To respond, hold the radio vertically 1 to 2 inches
(2.5 to 5.0 cm) from your mouth.
3 Press the PTT button to talk and release it to listen.
4 Press d to end the call.
5 You hear a short tone.
If Phone Call capability is not enabled in your radio, your radio
mutes the call.
22
English
NOTE: When you receive a Phone Call as an All Call, you can
respond to the call or end the call, only if an All Call
type is assigned to the channel.
NAG-LACR.book Page 23 Tuesday, March 12, 2013 3:37 PM
 Making a Call with the Channel Selector Knob
Making a Radio Call
 Making a Group Call
• The Channel Selector Knob.
To make a call to a group of users, your radio must be
configured as part of that group.
• A programmed One Touch Access button.
Procedure:
• A programmable button – This method is for Phone Calls only
1 Select the channel with the active group alias or ID. See
(see Making a Phone Call with the Programmable Phone
Button on page 26).
Selecting a Channel on page 18.
OR
Press the programmed One Touch Access button.
NOTE: Your radio must have the Privacy feature enabled on
the channel to send a privacy-enabled transmission.
Only target radios with the same Privacy Key OR the
same Key Value and Key ID as your radio will be able
to unscramble the transmission.
See Privacy on page 36 for more information.
The One Touch Access feature allows you to make a
Group or Private Call to a predefined ID easily. This
feature can be assigned to a short or long
programmable button press.You can ONLY have one
ID assigned to a One Touch Access button. Your
radio can have multiple One Touch Access buttons
programmed.
2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from
your mouth.
3 Press the PTT button to make the call. The LED lights up
solid green.
4 Wait for the Talk Permit Tone to finish (if enabled) and speak
clearly into the .
OR
Receiving and Making Calls
You can select a channel, subscriber ID or group ID by using:
Wait for the PTT Sidetone to finish (if enabled) and
speak clearly into the .
5 Release the PTT button to listen. When the target radio
responds, the LED blinks green.
23
English
NAG-LACR.book Page 24 Tuesday, March 12, 2013 3:37 PM
6 If the Channel Free Indication feature is enabled, you will
hear a short alert tone the moment the target radio releases
the PTT button, indicating the channel is free for you to
respond. Press the PTT button to respond.
OR
If there is no voice activity for a predetermined period of
time, the call ends.
Receiving and Making Calls
 Making a Private Call
There are two types of Private Calls. The first type, where a
radio presence check is performed prior to setting up the call,
while the other sets up the call immediately.
Only one of these call types can be programmed to your radio
by your dealer.
You hear a negative indicator tone, when you make a Private
Call via the One Touch Access button or the Channel
Selector Knob, if this feature is not enabled.
Use the Call Alert features to contact an individual radio. See
Call Alert Operation on page 32 for more information.
English
1 Select the channel with the active group alias or ID. See
Selecting a Channel on page 18.
OR
Press the programmed One Touch Access button.
2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from
your mouth.
3 Press the PTT button to make the call. The LED lights up
While you can receive and/or respond to a Private Call
initiated by an authorized individual radio, your radio
must be programmed for you to initiate a Private Call.
24
Procedure:
solid green.
4 Wait for the Talk Permit Tone to finish (if enabled) and speak
clearly into the .
5 Release the PTT button to listen. When the target radio
responds, the LED blinks green.
6 If the Channel Free Indication feature is enabled, you will
hear a short alert tone the moment the target radio releases
the PTT button, indicating the channel is free for you to
respond. Press the PTT button to respond.
OR
If there is no voice activity for a predetermined period of
time, the call ends.
7 You hear a short tone.
NAG-LACR.book Page 25 Tuesday, March 12, 2013 3:37 PM
 Making an All Call
Just like a Private Call, while you can receive and/or respond to
a Selective Call initiated by an authorized individual radio, your
radio must be programmed for you to initiate a Selective Call.
This feature allows you to transmit to all users on the channel.
Your radio must be programmed to allow you to use this feature.
Procedure:
1 Select the channel with the active group alias or ID. See
1 Select the channel with the active group alias or ID. See
Selecting a Channel on page 18.
4 Wait for the Talk Permit Tone to finish (if enabled) and speak
clearly into the .
5 Release the PTT button to listen. When the target radio
responds, the LED blinks green.
your mouth.
3 Press the PTT button to make the call. The LED lights up
solid green.
Selecting a Channel on page 18.
2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from
2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from
your mouth.
Procedure:
6 If the Channel Free Indication feature is enabled, you will
3 Press the PTT button to make the call. The LED lights up
solid green.
4 Wait for the Talk Permit Tone to finish (if enabled) and speak
clearly into the .
OR
Wait for the PTT Sidetone to finish (if enabled) and
speak clearly into the .
Receiving and Making Calls
 Making a Selective Call
Users on the channel cannot respond to an All Call.
hear a short alert tone the moment the target radio releases
the PTT button, indicating the channel is free for you to
respond. Press the PTT button to respond.
OR
If there is no voice activity for a predetermined period of
time, the call ends.
7 You hear a short tone.
25
English
NAG-LACR.book Page 26 Tuesday, March 12, 2013 3:37 PM
 Making a Phone Call with the Programmable
Phone Button
Procedure:
2 The LED lights up solid green.
This feature allows you to stop an ongoing Group or Private Call
to free the channel for transmission. For example, when a radio
experiences a “stuck ” condition where the PTT button is
inadvertently pressed by the user.
3 You hear the dialing tone of the telephone user.
Your radio must be programmed to allow you to use this feature.
4 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from
Procedure:
Receiving and Making Calls
1 Press the programmed Phone button.
26
Stopping a Radio Call
your mouth.
5 Press the PTT button to talk and release it to listen.
6 If the Channel Free Indication feature is enabled, you will
hear a short alert tone the moment the target radio releases
the PTT button, indicating the channel is free for you to
respond. Press the PTT button to respond.
OR
If there is no voice activity for a predetermined period of
time, the call ends.
7 You hear a short tone.
When you press PTT button while in the Phone Contacts
screen, a tone sounds.
When the telephone user ends the call, a tone sounds.
During the call, when you press One Touch Access button with
the deaccess code preconfigured, your radio attempts to end
the call.
English
While on the required channel:
1 Press the programmed Transmit Interrupt Remote Dekey
button.
2 Wait for acknowledgment.
3 The radio sounds a positive indicator tone, indicating that
the channel is now free.
OR
The radio sounds a negative indicator tone, indicating that
the radio is unable to free the channel.
Your radio sounds a negative indicator tone until you release
the PTT button, if it is transmitting an interruptible call that is
stopped via this feature.
NAG-LACR.book Page 27 Tuesday, March 12, 2013 3:37 PM
Monitoring Features
Talkaround
NOTE: This feature is not applicable in Capacity Plus and
Linked Capacity Plus.
Procedure:
 Monitoring a Channel
Use the Monitor feature to make sure a channel is free before
transmitting.
NOTE: This feature is not applicable in Capacity Plus and
Linked Capacity Plus.
Procedure:
1 Press the programmed Repeater/Talkaround button.
2 You hear a positive indicator tone, indicating the radio is in
Talkaround mode.
OR
You hear a negative indicator tone, indicating the radio is in
Repeater mode.
The Talkaround setting is retained even after powering down.
1 Press and hold the programmed Monitor button and listen
for activity.
2 You hear radio activity or total silence, depending on how
your radio is programmed.
3 When you hear “white noise” (that is, the channel is free),
press the PTT button to talk and release it to listen. The LED
lights up solid yellow.
Receiving and Making Calls
You can continue to communicate when your repeater is not
operating, or when your radio is out of the repeater’s range but
within talking range of other radios. This is called “talkaround”.
27
English
NAG-LACR.book Page 28 Tuesday, March 12, 2013 3:37 PM
 Permanent Monitor
Use the Permanent Monitor feature to continuously monitor a
selected channel for activity.
NOTE: This feature is not applicable in Capacity Plus and
Linked Capacity Plus.
Receiving and Making Calls
Procedure:
1 Press the programmed Permanent Monitor button.
2 Radio sounds alert tone, and the LED lights up solid yellow.
3 Press the programmed Permanent Monitor button to
remove the radio from permanent monitor mode.
4 Radio sounds an alert tone and the LED turns off.
28
English
NAG-LACR.book Page 29 Tuesday, March 12, 2013 3:37 PM
Scan Lists
Advanced Features
Scan lists are created and assigned to individual channels/
groups. Your radio scans for voice activity by cycling through the
channel/group sequence specified in the scan list for the current
channel.
Your radio supports up to 250 scan lists, with a maximum of 16
members in a list. Each scan list shall support a mixture of both
analog and digital entries.
NOTE: This feature is not applicable in Capacity Plus and
Linked Capacity Plus.
Advanced Features
Use this navigation guide to learn more about advanced
features available with your radio:
Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 29
Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 30
Call Indicator Settings . . . . . . . . . . . . . . . . . . . . . . . . . page 32
Call Alert Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . page 32
Emergency Operation . . . . . . . . . . . . . . . . . . . . . . . . . page 33
Privacy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 36
Multi-Site Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 37
Lone Worker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 38
Password Lock Features . . . . . . . . . . . . . . . . . . . . . . . page 38
Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 40
Auto-Range Transponder System (ARTS) . . . . . . . . . page 41
Over-the-Air Programming (OTAP) . . . . . . . . . . . . . . . page 42
Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 42
29
English
NAG-LACR.book Page 30 Tuesday, March 12, 2013 3:37 PM
 Starting and Stopping Scan
Scan
When you start a scan, your radio cycles through the
programmed scan list for the current channel looking for voice
activity.The LED blinks yellow.
During a dual mode scan, if you are on a digital channel, and
your radio locks onto an analog channel, it automatically
switches from digital mode to analog mode for the duration of
the call. This is also true for the reverse.
There are two types of scans:
Advanced Features
channels/groups in your scan list. On entering scan, your
radio may – depending on the settings – automatically start
on the last scanned “active” channel/group or on the channel
where scan was initiated.
• Auto Scan (Automatic): Your radio automatically starts
scanning when you select a channel/group that has Auto
Scan enabled.
NOTE: This feature is not applicable in Capacity Plus and
Linked Capacity Plus.
English
1 Press the programmed Scan button.
OR
Use the Channel Selector Knob to select a channel with
Auto Scan enabled.
2 When Scan is enabled, the LED blinks yellow and you hear
a positive indicator tone.
OR
When Scan is disabled, the LED turns off and you hear a
negative indicator tone.
• Main Channel Scan (Manual): Your radio scans all the
30
Procedure:
 Responding to a Transmission During a Scan
During scanning, your radio stops on a channel/group where
activity is detected. The radio stays on that channel for a
programmed time period known as “hang time”.
Procedure:
1 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from
your mouth.
If the Channel Free Indication feature is enabled, you
will hear a short alert tone the moment the transmitting radio
releases the PTT button, indicating the channel is free for
you to respond.
NAG-LACR.book Page 31 Tuesday, March 12, 2013 3:37 PM
2 Press the PTT button during hang time. The LED lights up
solid green.
clearly into the microphone.
OR
Wait for the PTT Sidetone to finish (if enabled) and
speak clearly into the microphone.
4 Release the PTT button to listen.
 Deleting a Nuisance Channel
• Turn the radio off and power it on again, OR
• Stop and restart a scan via the programmed Scan button, OR
• Change the channel via the Channel Selector Knob.
5 If you do not respond within the hang time, the radio returns
to scanning other channels/groups.
Procedure:
To restore the deleted nuisance channel, do one of the
following:
If a channel continually generates unwanted calls or noise
(termed a “nuisance” channel), you can temporarily remove the
unwanted channel from the scan list.
Vote Scan
Vote Scan provides you with wide area coverage in areas where
there are multiple base stations transmitting identical
information on different analog channels.
This capability does not apply to the channel designated as the
Selected Channel.
Your radio scans analog channels of multiple base stations and
performs a voting process to select the strongest received
signal. Once that is established, your radio unmutes to
transmissions from that base station.
Procedure:
The LED blinks yellow during the Vote Scan operation.
1 When your radio “locks on to” an unwanted or nuisance
channel, press the programmed Nuisance Channel Delete
button until you hear a tone.
Advanced Features
3 Wait for the Talk Permit Tone to finish (if enabled) and speak
 Restoring a Nuisance Channel
To respond to a transmission during a Vote Scan, follow the
same procedures as Responding to a Transmission During a
Scan on page 30.
2 Release the Nuisance Channel Delete button. The
nuisance channel is deleted.
31
English
NAG-LACR.book Page 32 Tuesday, March 12, 2013 3:37 PM
Call Indicator Settings
 Making a Call Alert with the One Touch Access
You can turn on or off the ringing tones for a received Private
Call (see Turning Radio Tones/Alerts On or Off on page 43).
a Call Alert to the predefined ID.
Your radio can be programmed by your dealer to continually
alert you when a radio call remains unanswered. This is done
by automatically increasing the alarm tone volume over time.
Advanced Features
Call Alert Operation
Procedure:
When you receive a Call Alert page:
1 You hear a repetitive tone. The LED blinks yellow.
2 Press the PTT button within four (4) seconds of receiving a
Call Alert page to respond to the Private Call.
32
English
2 The LED lights up solid green when your radio is sending
the Call Alert.
Call Alert paging enables you to alert a specific radio user to call
you back when they are able to do so. This feature is accessible
via a programmed One Touch Access button.
 Receiving and Responding to a Call Alert
Procedure:
1 Press the programmed One Touch Access button to make
 Escalating Alarm Tone Volume
This feature is known as Escalert.
Button
3 If the Call Alert acknowledgement is received, two chirps
sound.
OR
If the Call Alert acknowledgement is not received, a lowpitch tone sounds.
NAG-LACR.book Page 33 Tuesday, March 12, 2013 3:37 PM
In addition, each alarm has the following types:
Emergency Operation
Your dealer can set the duration of a button press for the
programmed Emergency button, except for long press, which is
similar with all other buttons:
• Short press – Between 0.05 seconds and 0.75 seconds
• Regular – Radio transmits an alarm signal and shows audio
and/or visual indicators.
• Silent – Radio transmits an alarm signal without any audio or
visual indicators. Radio receives calls without any sound
through the radio’s speaker, until you press the PTT button to
initiate the call.
• Silent with Voice – Radio transmits an alarm signal without
any audio or visual indicators, but allow incoming calls to
sound through the radio’s speaker.
• Long press – Between 1.00 second and 3.75 seconds
The Emergency button is assigned with the Emergency On/Off
feature. Check with your dealer for the assigned operation of
the Emergency button.
Only one of the Emergency Alarms above can be assigned to
the programmed Emergency button.
 Sending an Emergency Alarm
If short press the Emergency button is assigned to turn on the
Emergency mode, then long press the Emergency button is
assigned to exit the Emergency mode.
This feature allows you to send an Emergency Alarm, a nonvoice signal, which triggers an alert indication on a group of
radios.
If long press the Emergency button is assigned to turn on the
Emergency mode, then short press the Emergency button is
assigned to exit the Emergency mode.
Procedure:
Your radio supports three Emergency Alarms:
Advanced Features
An Emergency Alarm is used to indicate a critical situation. You
are able to initiate an Emergency at any time, in any state, even
when there is activity on the current channel.
1 Press the programmed Emergency On button.
2 The LED lights up solid green.
• Emergency Alarm
• Emergency Alarm with Call
• Emergency Alarm with Voice to Follow
33
English
NAG-LACR.book Page 34 Tuesday, March 12, 2013 3:37 PM
3 When an Emergency Alarm acknowledgment is received,
the Emergency tone sounds. The LED blinks green.
OR
If your radio does not receive an Emergency Alarm
acknowledgement, and after all retries have been
exhausted, a low-pitch tone sounds.
If your radio is set to Silent, it will not display any audio or visual
indicators during Emergency mode.
Advanced Features
1 Press the programmed Emergency On button.
2 The LED lights up solid green.
3 When an Emergency Alarm acknowledgment is received,
the Emergency tone sounds. The LED blinks green.
4 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from
your mouth.
5 Press the PTT button to make the call. The LED lights up
34
solid green.
English
Wait for the PTT Sidetone to finish (if enabled) and
speak clearly into the microphone.
8 When the channel is free for you to respond, a short alert
tone sounds (
if the Channel Free Indication feature is
enabled). Press the PTT button to respond.
OR
Once your call ends, press Emergency Off button to exit
the Emergency mode.
This feature allows you to send an Emergency Alarm to a group
of radios. Upon acknowledgement by a radio within the group,
the group of radios can communicate over a programmed
Emergency channel.
Procedure:
clearly into the microphone.
OR
7 Release the PTT button to listen.
4 Radio exits the Emergency Alarm mode.
 Sending an Emergency Alarm with Call
6 Wait for the Talk Permit Tone to finish (if enabled) and speak
If your radio is set to Silent, it will not display any audio or visual
indicators during Emergency mode, or allow any received calls
to sound through the radio’s speaker, until you press the PTT
button to initiate the call.
If your radio is set to Silent with Voice, it will not display any
audio or visual indicators during Emergency mode, but allow
incoming calls to sound through the radio’s speaker. The
indicators will only appear once you press the PTT button to
initiate, or respond to, the call.
NAG-LACR.book Page 35 Tuesday, March 12, 2013 3:37 PM
 Sending an Emergency Alarm with Voice to
This feature allows you to send an Emergency Alarm to a group
of radios. Your radio’s microphone is automatically activated,
allowing you to communicate with the group of radios without
pressing the PTT button.
This activated microphone state is also known as “hot mic”.
If you press the PTT button during the programmed hot mic
transmission period, the radio ignores the PTT press and
remains in Emergency mode.
1 Press the programmed Emergency On button.
2 The LED lights up solid green.
5 To transmit again, press the PTT button.
OR
Press the programmed Emergency Off button to exit the
Emergency mode.
NOTE: If you press the PTT button during hot mic, and
continue to press it after the hot mic duration expires, the radio
continues to transmit until you release the PTT button.
Procedure:
Once the cycling duration between hot mic and receiving
calls expires, if Emergency Cycle Mode is enabled.
OR
Once the hot mic duration expires, if Emergency Cycle
Mode is disabled.
3 Once a tone sounds, speak clearly into the microphone.
When hot mic has been enabled, the radio automatically
transmits without a PTT press until the hot mic duration
expires.
While transmitting, the LED lights up solid green.
If your radio is set to Silent, it will not display any audio or visual
indicators during Emergency mode, or allow any received calls
to sound through the radio’s speaker, until the programmed hot
mic transmission period is over, and you press the PTT button.
Advanced Features
Follow
4 The radio automatically stops transmitting when:
If your radio is set to Silent with Voice, it will not display any
audio or visual indicators during Emergency mode when you
are making the call with hot mic, but allow sound through the
radio’s speaker when the target radio responds after the
programmed hot mic transmission period is over. The indicators
will only appear when you press the PTT button.
NOTE: If the Emergency Alarm request fails, the radio does
not retry to send the request, and enters the hot mic
state directly.
35
English
NAG-LACR.book Page 36 Tuesday, March 12, 2013 3:37 PM
 Reinitiating an Emergency Mode
NOTE:
This feature is only applicable to the radio sending the
Emergency Alarm.
There are two instances where this can happen:
• You change the channel while the radio is in Emergency
mode. This exits the Emergency mode. If Emergency Alarm is
enabled on this new channel, the radio reinitiates Emergency.
• You press the programmed Emergency On button during an
Advanced Features
36
NOTE: This feature is only applicable to the radio sending the
Emergency Alarm.
Your radio exits Emergency mode when one of the following
occurs:
• Emergency Alarm acknowledgement is received (for
Emergency Alarm only), OR
•
An Emergency Exit Telegram is received, OR
• All retries to send the alarm have been exhausted, OR
• The Emergency Off button is pressed.
• Turn the radio off and then power it on again if your radio has
been programmed to remain on the Emergency Revert
channel even after acknowledgement is received.
English
Privacy
If enabled, this feature helps to prevent eavesdropping by
unauthorized users on a channel by the use of a softwarebased scrambling solution. The signaling and user identification
portions of a transmission are not scrambled.
Emergency initiation/transmission state. This causes the
radio to exit this state, and to reinitiate Emergency.
 Exiting an Emergency Mode
NOTE: If your radio is powered off, it exits the Emergency
mode. The radio will not reinitiate the Emergency
mode automatically when it is turned on again.
Your radio must have privacy enabled on the channel to send a
privacy-enabled transmission, although this is not a necessary
requirement for receiving a transmission. While on a privacyenabled channel, the radio is still able to receive clear
(unscrambled) transmissions.
Your radio supports two types of privacy:
• Basic Privacy
• Enhanced Privacy (A Software License Key sold separately is
required for this feature.)
Only ONE of the privacy types above can be assigned to the
radio.
To unscramble a privacy-enabled call or data transmission, your
radio must be programmed to have the same Privacy Key (for
Basic Privacy), OR the same Key Value and Key ID (for
Enhanced Privacy) as the transmitting radio.
NAG-LACR.book Page 37 Tuesday, March 12, 2013 3:37 PM
The LED lights up solid green while the radio is transmitting and
blinks green rapidly when the radio is receiving an ongoing
privacy-enabled transmission.
 Starting an Automatic Site Search
NOTE: The radio only scans for a new site if the current signal
is weak or when the radio is unable to detect any
signal from the current site. If the RSSI value is strong,
the radio remains on the current site.
Procedure:
NOTE: Some radio models may not offer this Privacy feature.
Check with your dealer or system administrator for
more information.
1 Press the programmed Site Lock On/Off button.
Procedure:
Press the programmed Privacy button to toggle privacy on or
off.
3 The LED blinks yellow rapidly when the radio is actively
Multi-Site Controls
These features are applicable when your current radio channel
is part of an IP Site Connect or Linked Capacity Plus
configuration.
NOTE: See IP Site Connect on page 10 and Linked
Capacity Plus on page 12 for more details about
these configurations.
2 A tone sounds.
searching for a new site, and turns off once the radio locks
on to a site.
Advanced Features
If your radio receives a scrambled call that is of a different
Privacy Key, OR a different Key Value and Key ID, you will
either hear a garbled transmission (Basic Privacy) or nothing at
all (Enhanced Privacy).
The radio also performs an automatic site search (site is
unlocked) during a PTT button press or data transmission if
the current channel, multi-site channel with an attached roam
list, is out of range.
 Stopping an Automatic Site Search
When the radio is actively searching for a new site:
Procedure:
1 Press the programmed Site Lock On/Off button.
2 A tone sounds and the LED turns off.
37
English
NAG-LACR.book Page 38 Tuesday, March 12, 2013 3:37 PM
 Starting a Manual Site Search
• Emergency Alarm with Call
Procedure:
• Emergency Alarm with Voice to Follow
1 Press the programmed Manual Site Roam button.
2 A tone sounds and the LED blinks green.
3 You hear a positive indicator tone and the LED turns off,
indicating the radio is locked on to a site.
OR
You hear a negative indicator tone and the LED turns off,
indicating the radio is unable to lock on to a site.
The radio remains in the emergency state allowing voice
messages to proceed until action is taken. See Emergency
Operation on page 33 on ways to exit Emergency.
NOTE: This feature is limited to radios with this function
enabled. Check with your dealer or system
administrator for more information.
Password Lock Features
Advanced Features
Lone Worker
38
This feature prompts an emergency to be raised if there is no
user activity, such as any radio button press or activation of the
channel selector, for a predefined time.
Following no user activity for a programmed duration, the radio
pre-warns the user via an audio indicator once the inactivity
timer expires.
If there is still no acknowledgment by the user before the
predefined reminder timer expires, the radio initiates an
Emergency Alarm.
Only one of the following Emergency Alarms is assigned to this
feature:
• Emergency Alarm
English
If enabled, this feature allows you to access your radio via
password upon powering up. Use the Channel Selector Knob
and the three Side Buttons to enter password (see Linked
Capacity Plus page 12 on page 6):
• Channel Selector Knob positions 1 to 9 represent
numbers 1 to 9, and position 10 represents number 0.
• Side Buttons 1 to 2 represent numbers 1 to 2.
 Accessing the Radio from Password
Procedure:
Power up the radio.
1 You hear a continuous tone.
NAG-LACR.book Page 39 Tuesday, March 12, 2013 3:37 PM
2 Use the Channel Selector Knob to enter the first digit of the
password.
three digits of the password. You hear a positive indicator
tone for each Side Button press.
When the second digit of the password is entered, your
radio ignores any Channel Selector Knob position change.
4 When the last digit of the four-digit password is entered,
your radio automatically checks the validity of the password.
If the password is correct:
Your radio proceeds to power up. See Powering Up the
Radio on page 5.
OR
If the password is incorrect:
You hear a continuous tone. Repeat Steps 1 to 3.
OR
After the third incorrect password, your radio enters into
locked state. A tone sounds and the LED double blinks
yellow.
Procedure:
Wait for 15 minutes. Repeat Steps 1 to 4 in Accessing the
Radio from Password on page 38.
OR
Power up the radio, if you have powered down the radio during
locked state:
1 A tone sounds and the LED double blinks yellow.
2 Wait for 15 minutes. Repeat Steps 1 to 4 in Accessing the
Radio from Password on page 38.
Your radio restarts the 15 minute timer for locked state when
you power up.
Advanced Features
3 Press Side Button 1 or 2 to enter each digit of the remaining
 Unlocking the Radio from Locked State
Your radio enters into locked state for 15 minutes, and responds
to inputs from On/Off/Volume Control Knob.
NOTE: The radio is unable to receive any call, including
emergency calls, in locked state.
39
English
NAG-LACR.book Page 40 Tuesday, March 12, 2013 3:37 PM
Bluetooth
 Finding and Connecting to a Bluetooth Device
This feature allows you to use your radio with a Bluetoothenabled device (accessory) via a Bluetooth connection. Your
radio supports both Motorola and COTS (Commercially
available Off-The-Shelf) Bluetooth-enabled devices.
Bluetooth operates within a range of 10 meters line of sight.
This is an unobstructed path between your radio and your
Bluetooth-enabled device.
Advanced Features
1 Turn on your Bluetooth-enabled device and place it in
pairing mode. Refer to respective Bluetooth-enabled
device’s user manual.
2 On your radio, press the programmed Bluetooth Connect
button.
3 A tone sounds and LED blinks yellow.
It is not recommended that you leave your radio behind and
expect your Bluetooth-enabled device to work with a high
degree of reliability when they are separated.
40
Procedure:
At the fringe areas of reception, both voice and tone quality will
start to sound "garbled" or "broken". To correct this problem,
simply position your radio and Bluetooth-enabled device closer
to each other (within the 10-meter defined range) to re-establish
clear audio reception. Your radio’s Bluetooth function has a
maximum power of 2.5 mW (4 dBm) at the 10-meter range.
Your radio can support up to 3 simultaneous Bluetooth
connections with Bluetooth-enabled devices of unique types.
For example, a headset, a scanner, and a PTT-Only Device
(POD). Multiple connections with Bluetooth-enabled devices of
the same type are not supported.
Refer to your respective Bluetooth-enabled device’s user
manual for more details on your Bluetooth-enabled device’s full
capabilities.
English
4 Your Bluetooth-enabled device may require additional steps
to complete the pairing. Refer to respective Bluetoothenabled device’s user manual.
5 If successful, a positive tone sounds.
OR
If unsuccessful, a negative indicator tone sounds.
Do not turn off your Bluetooth-enabled device during the finding
and connecting operation as this cancels the operation.
Your radio connects to the Bluetooth-enabled device within
range with either the strongest signal strength, or to one which it
has connected to before in a prior session.
NOTE: A pin code may be required to be programmed in your
radio before it can pair with some devices. Contact
your dealer for more information.
NAG-LACR.book Page 41 Tuesday, March 12, 2013 3:37 PM
Procedure:
1 Press the programmed Bluetooth Disconnect button.
2 A positive indicator tone sounds when disconnected.
ARTS is an analog-only feature designed to inform you when
your radio is out-of-range of other ARTS-equipped radios.
 Switching Audio Route
ARTS-equipped radios transmit or receive signals periodically
to confirm that they are within range of each other. Your dealer
can program your radio to transmit or receive the ARTS signal.
You can toggle audio routing between internal radio speaker
and external Bluetooth-enabled accessory.
Procedure:
Your radio provides indications of states as follows:
1 Press the programmed Bluetooth Audio Switch button.
• First-Time Alert – A tone sounds.
• ARTS-in-Range Alert – A tone sounds, if programmed.
A tone sounds when the audio route has switched.
• ARTS-Out-of-Range Alert – A tone sounds, and the LED
Advanced Features
Auto-Range Transponder System
(ARTS)
 Disconnecting from a Bluetooth Device
rapidly blinks red.
41
English
NAG-LACR.book Page 42 Tuesday, March 12, 2013 3:37 PM
Utilities
Over-the-Air Programming (OTAP)
Your radio can be updated by your dealer remotely, via OTAP,
without needing to be physically connected. Additionally, some
settings can also be configured via OTAP.
While undergoing OTAP, the LED blinks green.
NOTE: When the radio is receiving high volume data, the
channel is busy. A PTT button press at this time
causes a negative tone to sound.
 Setting the Squelch Level
You can adjust your radio's squelch level to filter out unwanted
calls with low signal strength or channels that have a higher
than normal background noise.
Settings: Normal is the default. Tight filters out (unwanted)
calls and/or background noise. However, calls from remote
locations may also be filtered out.
Once the programming is complete, a tone sounds, and your
radio restarts (powers off and on again).
Procedure:
Advanced Features
1 Press the programmed Squelch button.
42
English
2 You hear a positive indicator tone, indicating the radio is
operating in tight squelch.
OR
You hear a negative indicator tone, indicating the radio is
operating in normal squelch.
 Setting the Power Level
You can toggle your radio’s power setting between high or low
for each channel.
Settings: High enables communication with radios located at a
considerable distance from you. Low enables communication
with radios in closer proximity.
NAG-LACR.book Page 43 Tuesday, March 12, 2013 3:37 PM
Procedure:
1 Press the programmed Power Level button.
2 You hear a positive indicator tone, indicating the radio is
transmitting at low power.
OR
You hear a negative indicator tone, indicating the radio is
transmitting at high power.
If the Talk Permit Tone feature is enabled, use a trigger word to
initiate the call. Wait for the Talk Permit Tone to finish before
speaking clearly into the microphone.
 Turning the Howling Suppressor Feature On or Off
 Turning the Voice Operating Transmission (VOX)
Feature On or Off
This feature allows you to initiate a hands-free voice activated
call on a programmed channel. The radio automatically
transmits, for a programmed period, whenever the microphone
on the VOX-capable accessory detects voice.
Pressing the PTT button during radio operation will disable
VOX. To re-enable VOX, do one of the following:
• Turn the radio off and power it on again, OR
• Change the channel via the Channel Selector Knob, OR
This feature allows you to minimize acoustic feedback in
received calls.
Procedure:
Advanced Features
Procedure:
Press the programmed VOX button to toggle the feature on or
off.
1 Press the programmed AF Suppressor button.
2 You hear a positive indicator tone, indicating that Howling
Suppressor is now enabled.
OR
You hear a negative indicator tone, indicating that the radio
is unable to activate Howling Suppressor.
• Follow the procedure below.
 Turning Radio Tones/Alerts On or Off
NOTE: Turning this feature on or off is limited to radios with
this function enabled. Check with your dealer or
system administrator for more information.
You can enable and disable all radio tones and alerts (except for
the incoming Emergency alert tone) if needed.
Procedure:
1 Press the programmed All Tones/Alerts button.
43
English
NAG-LACR.book Page 44 Tuesday, March 12, 2013 3:37 PM
2 You hear a positive indicator tone, indicating all tones and
alerts are on.
OR
You hear a negative indicator tone, indicating all tones and
alerts are off.
 Checking the Battery Strength
You can check how much battery power you have left.
Settings: The LED Indicator in solid yellow indicates fair battery
charge while solid green indicates full charge of the battery.
Advanced Features
Procedure:
Press the programmed Battery Strength button to view the
battery strength via the LED Indicator.
44
English
NAG-LACR.book Page 45 Tuesday, March 12, 2013 3:37 PM
Batteries
Accessories
• Li-Ion, 1600mAH IP67 Battery (PMNN4440_)
Cables
• Programming Cable USB (PMKN4115_)
• Programming Cable Slim Connector to DB25 and USB Plug
(PMKN4117_)
Accessories
Your radio is compatible with the accessories listed in this
chapter. Contact your dealer for details.
Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 45
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 45
Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 45
Carry Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 45
Chargers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 45
Earbuds and Earpieces . . . . . . . . . . . . . . . . . . . . . . . . page 46
Headsets and Headset Accessories . . . . . . . . . . . . . . page 47
Remote Speaker s . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 47
Surveillance Accessories. . . . . . . . . . . . . . . . . . . . . . . page 48
Miscellaneous Accessories . . . . . . . . . . . . . . . . . . . . . page 48
• Programming Cable Slim Connector to DB25 and TTR
(PMKN4116_)
Carry Devices
• Plastic Carry Case with Belt Clip (PMLN6545_)
Antennas
• VHF, 136 – 148MHz, Stubby Antenna (PMAD4119_)
Chargers
• VHF, 146 – 160MHz, Stubby Antenna (PMAD4120_)
• Single-Unit Charger, US Plug (PMTN4024_)
• VHF, 160 – 174MHz, Stubby Antenna (PMAD4121_)
• Single-Unit Charger, EURO Plug (PMTN4025_)
• UHF, 403 – 450MHz, Stubby Antenna (PMAE4069_)
• Single-Unit Charger, UK Plug (PMTN4026_)
• UHF, 440 – 490MHz, Stubby Antenna (PMAE4070_)
• Core Single-Unit Charger, with Power Supply, US
• UHF, 470 – 527MHz, Stubby Antenna (PMAE4071_)
(AAHTN3000_)
• Core Single-Unit Charger, Base Only (HTN9000_)
45
English
NAG-LACR.book Page 46 Tuesday, March 12, 2013 3:37 PM
• Core Single-Unit Charger, Base Only (MDHTN9000_)
• Core Single-Unit Charger, with Switch Mode Power Supply,
UK (PMLN5195_)
• Core Single-Unit Charger, with Switch Mode Power Supply,
EURO (PMLN5196_)
• Core Single-Unit Charger, with Switch Mode Power Supply,
US (PMLN5197_)
• IMPRES Single-Unit Charger, with Power Supply, US
(WPLN4182_)
• IMPRES Single-Unit Charger, with Power Supply, EURO
(WPLN4184_)
• IMPRES Single-Unit Charger, without Power Supply, US
Accessories
(WPLN4199_)
• IMPRES Single-Unit Charger, with Power Supply
(WPLN4206_)
• IMPRES Single-Unit Charger, with Switch Mode Power
Supply, EURO (PMLN5188_)
• IMPRES Single-Unit Charger, with Switch Mode Power
Supply, UK (PMLN5194_)
• IMPRES Single-Unit Charger, with Switch Mode Power
Supply, US (PMLN5198_)
46
English
Supply, Australia/New Zealand (PMLN5199_)
• Daisy Chain Charger (JMTN4011_)
• Multi-Unit Charger, UK Cord (WPLN4188_)
• Multi-Unit Charger, EURO Cord (WPLN4189_)
• Multi-Unit Charger, Australia/New Zealand Cord
(WPLN4190_)
• Multi-Unit Charger, no Power Cord (WPLN4197_)
• IMPRES Single-Unit Charger, with Power Supply, UK
(WPLN4183_)
• IMPRES Single-Unit Charger, with Switch Mode Power
• Multi-Unit Charger, US Cord (WPLN4205_)
• Multi-Unit Charger, with Display, US Plug (WPLN4192_)
• Multi-Unit Charger, with Display, UK Plug (WPLN4193_)
• Multi-Unit Charger, with Display, EURO Plug (WPLN4194_)
• Multi-Unit Charger, with Display, Australia/New Zealand Plug
(WPLN4195_)
• Multi-Unit Charger, with Display, no Power Cord
(WPLN4198_)
• Multi-Unit Charger, with Display, US Plug (WPLN4204_)
• Micro USB Travel Charger (SPN5334_)
Earbuds and Earpieces
• Earbud with In-Line Mic/PTT, MagOne (PMLN5733_)
NAG-LACR.book Page 47 Tuesday, March 12, 2013 3:37 PM
• Earpiece In-Line Mic/PTT Swivel, MagOne (PMLN5727_)
• Non-Secure Wireless Headset & Push-to-Talk Device with
Speaker (AARLN4885_)
• Receive-Only Flexible Earpiece for Remote Speaker
(WADN4190_)
• D-Shell Receive Only Earpiece (One Size) for Remote
• Non-Secure Wireless Headset & Push-to-Talk Device with
Push-to-Talk Audio, 9.5-Inch Cable (NNTN8126_)
• Non-Secure Wireless Headset & Push-to-Talk Device with
Push-to-Talk Audio, 9-Inch Cable with Euro/UK Plug
(GMTN6356_)
Speaker (PMLN4620_)
• Receiver-Only Earpiece with Translucent Tube and Rubber
Eartip for Remote Speaker (RLN4941_)
• 1-Wire Earbud, 29cm Cord, Black (NNTN8294_)
• 1-Wire Earbud,116cm Cord, Black (NNTN8295_)
• Wireless Earpiece Maintenance Kit (NTN8821_)
• Non-Secure Wireless Push-to-Talk Device (NNTN8127_)
• Push-to-Talk Module, without Charger (NNTN8191_)
• Non-Secure HK200 Mobile Bluetooth Headset with US Plug
(89409N)
• Replacement Earpiece 12” Cable (for NNTN8125_)
(NTN2572_)
• Ear Straps for CommPort Earpiece (for Secure Attachment to
Ear), Pack of 10 (NTN8988_)
• Replacement Earpiece 9.5” Cable (for NNTN8126_)
(NTN2575_)
• Replacement Ear Tubes for CommPort Earpiece, Pack of 10
(RLN5037_)
• Replacement Ear Tips Kit for Wireless Ear Buds
(NNTN8316_)
Headsets and Headset Accessories
• Heavy Duty Headset, Noise Cancelling with In-Line PTT
(PMLN5731_)
• Earset with Boom Microphone, MagOne (PMLN5732_)
Accessories
Push-to-Talk Audio, 12-Inch Cable
(NNTN8125_)(NNTN8189_)
• Receive-Only Covered Earbud with Coiled Cord, for Remote
• Non-Secure Wireless Push-to-Talk Device (for NNTN8125_
and NNTN8126_) (NNTN8143_)
•
Remote Speaker s
• IMPRES Remote Speaker Large, Noise Cancelling with
3.5mm Jack (PMMN4071_)
47
English
NAG-LACR.book Page 48 Tuesday, March 12, 2013 3:37 PM
• IMPRES Remote Speaker Small, with 3.5mm Jack
(PMMN4073_)
• Remote Speaker Small, No Emergency, IP57 (PMMN4075_)
• Remote Speaker Small with 3.5mm Jack (PMMN4076_)
Surveillance Accessories
• 2-Wire Surveillance Kit, Black (PMLN5724_)
• 2-Wire Surveillance Kit, Beige (PMLN5726_)
Miscellaneous Accessories
Accessories
• Replacement Micro-USB Plug-In Charger (PMPN4009_)
48
English
NAG-LACR.book Page 49 Tuesday, March 12, 2013 3:37 PM
Take a moment to review the following:
Special Channel Assignments . . . . . . . . . . . . . . . . . . . page 49
Operating Frequency Requirements . . . . . . . . . . . . . . page 50
Declaration of Compliance for the Use of
Distress and Safety Frequencies . . . . . . . . . . . . . . . page 52
Technical Parameters for Interfacing
External Data Sources . . . . . . . . . . . . . . . . . . . . . . . page 52
Special Channel Assignments
 Emergency Channel
Repeat “MAYDAY” and the name of the vessel.
“WE ARE LOCATED AT _______________________.”
State the position of the vessel in distress, using any
information that will help responders to locate you, e.g.:
• latitude and longitude
• bearing (state whether you are using true or magnetic
north)
• distance to a well-known landmark
• vessel course, speed or destination
5 State the nature of the distress.
6 Specify what kind of assistance you need.
7 State the number of persons on board and the number
needing medical attention, if any.
8 Mention any other information that would be helpful to
responders, such as type of vessel, vessel length and/or
tonnage, hull color, etc.
9 “OVER.”
10 Wait for a response.
11 If you do not receive an immediate response, remain by the
radio and repeat the transmission at intervals until you
receive a response. Be prepared to follow any instructions
given to you.
Appendix: Maritime Radio Use in the VHF Frequency Range
Appendix: Maritime Radio Use in the
VHF Frequency Range
If you are in imminent and grave danger at sea and require
emergency assistance, use VHF Channel 16 to send a distress
call to nearby vessels and the United States Coast Guard.
Transmit the following information, in this order:
“MAYDAY, MAYDAY, MAYDAY.”
“THIS IS _____________________, CALL SIGN
__________.”
State the name of the vessel in distress 3 times, followed
by the call sign or other identification of the vessel, stated 3
times.
49
English
NAG-LACR.book Page 50 Tuesday, March 12, 2013 3:37 PM
Appendix: Maritime Radio Use in the VHF Frequency Range
 Non-Commercial Call Channel
For non-commercial transmissions, such as fishing reports,
rendezvous arrangements, repair scheduling, or berthing
information, use VHF Channel 9.
Operating Frequency Requirements
A radio designated for shipboard use must comply with Federal
Communications Commission Rule Part 80 as follows:
Additional information about operating requirements in the
Maritime Services can be obtained from the full text of FCC
Rule Part 80 and from the US Coast Guard.
Table A-1: VHF Marine Channel List
Transmit
Receive
10
11
12
13**
14
15**
16
17**
18
19
156.050
156.100
156.150
156.200
156.250
156.300
156.350
156.400
156.450
156.500
156.550
156.600
156.650
156.700
156.750
156.800
156.850
156.900
156.950
160.650
160.700
160.750
160.800
160.850
–
160.950
–
156.450
156.500
156.550
156.600
156.650
156.700
156.750
156.800
156.850
161.500
161.550
• on ships subject to Part II of Title III of the Communications
Act, the radio must be capable of operating on the 156.800
MHz frequency
• on ships subject to the Safety Convention, the radio must be
capable of operating:
• in the simplex mode on the ship station transmitting
frequencies specified in the 156.025 – 157.425 MHz
frequency band, and
• in the semiduplex mode on the two frequency channels
specified in the table below.
NOTE: Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83
cannot be lawfully used by the general public in US
waters.
50
English
Frequency (MHz)
Channel
Number
NAG-LACR.book Page 51 Tuesday, March 12, 2013 3:37 PM
Table A-1: VHF Marine Channel List (Continued)
Frequency (MHz)
Transmit
Receive
20
22
24
25
26
27
28
60
62
63
65
66
67**
68
69
71
72
73
157.000
157.050
157.100
157.150
157.200
157.250
157.300
157.350
157.400
156.025
156.075
156.125
156.175
156.225
156.275
156.325
156.375
156.425
156.475
156.575
156.625
156.675
161.600
161.650
161.700
161.750
161.800
161.850
161.900
161.950
162.000
160.625
160.675
160.725
160.775
160.825
160.875
160.925
156.375
156.425
156.475
156.575
–
156.675
Frequency (MHz)
Channel
Number
Transmit
Receive
74
75
76
77**
78
79
80
84
85
86
87
88
156.725
***
***
156.875
156.925
156.975
157.025
157.075
157.125
157.175
157.225
157.275
157.325
157.375
157.425
156.725
***
***
–
161.525
161.575
161.625
161.675
161.725
161.775
161.825
161.875
161.925
161.975
162.025
Appendix: Maritime Radio Use in the VHF Frequency Range
Channel
Number
Table A-1: VHF Marine Channel List (Continued)
* Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be
lawfully used by the general public in US waters.
** Low power (1 W) only
*** Guard band
NOTE: A – in the Receive column indicates that the channel is
transmit only.
51
English
Appendix: Maritime Radio Use in the VHF Frequency Range
NAG-LACR.book Page 52 Tuesday, March 12, 2013 3:37 PM
Declaration of Compliance for the Use of
Distress and Safety Frequencies
The radio equipment does not employ a modulation other than
the internationally adopted modulation for maritime use when it
operates on the distress and safety frequencies specified in
RSS-182 Section 7.3.
52
English
Technical Parameters for Interfacing
External Data Sources
Input Voltage (Volts
Peak-to-peak)
Max Data Rate
Impedance
RS232
USB
SB9600
18V
3.6V
5V
28 kb/s
5k ohm
12 Mb/s
90 ohm
9.6 kb/s
120 ohm
NAG-LACR.book Page 53 Tuesday, March 12, 2013 3:37 PM
Batteries and Chargers Warranty
The Capacity Warranty
The capacity warranty guarantees 80% of the rated capacity for the
The workmanship warranty guarantees against defects in
workmanship under normal use and service.
All MOTOTRBO Batteries
Two (2) Years
IMPRES Chargers (Single-Unit and Multi-Unit,
Non-Display)
Two (2) Years
IMPRES Chargers (Multi-Unit with Display)
One (1) Year
Lithium-Ion (Li-lon) Batteries
12 Months
IMPRES Batteries, When Used Exclusively
with IMPRES Chargers
18 Months
Batteries and Chargers Warranty
warranty duration.
The Workmanship Warranty
53
English
NAG-LACR.book Page 54 Tuesday, March 12, 2013 3:37 PM
This express limited warranty is extended by MOTOROLA to the
original end user purchaser only and is not assignable or
transferable to any other party. This is the complete warranty for the
Product manufactured by MOTOROLA. MOTOROLA assumes no
obligations or liability for additions or modifications to this warranty
unless made in writing and signed by an officer of MOTOROLA.
Limited Warranty
MOTOROLA COMMUNICATION PRODUCTS
I. WHAT THIS WARRANTY COVERS AND FOR HOW
LONG:
MOTOROLA SOLUTIONS, INC. (“MOTOROLA”) warrants the
MOTOROLA manufactured Communication Products listed below
(“Product”) against defects in material and workmanship under
normal use and service for a period of time from the date of
purchase as scheduled below:
XPR Series Digital Portable
Limited Warranty
Radios
Product Accessories (Excluding
Batteries, Chargers and Mag One
Accessories)
Mag One Accessories
English
MOTOROLA cannot be responsible in any way for any ancillary
equipment not furnished by MOTOROLA which is attached to or
used in connection with the Product, or for operation of the Product
with any ancillary equipment, and all such equipment is expressly
excluded from this warranty. Because each system which may use
the Product is unique, MOTOROLA disclaims liability for range,
coverage, or operation of the system as a whole under this
warranty.
Two (2) Years
One (1) Year
II. GENERAL PROVISIONS:
Six (6) Months
MOTOROLA, at its option, will at no charge either repair the
Product (with new or reconditioned parts), replace it (with a new or
reconditioned Product), or refund the purchase price of the Product
during the warranty period provided it is returned in accordance
with the terms of this warranty. Replaced parts or boards are
warranted for the balance of the original applicable warranty period.
All replaced parts of Product shall become the property of
MOTOROLA.
54
Unless made in a separate agreement between MOTOROLA and
the original end user purchaser, MOTOROLA does not warrant the
installation, maintenance or service of the Product.
This warranty sets forth the full extent of MOTOROLA'S
responsibilities regarding the Product. Repair, replacement or
refund of the purchase price, at MOTOROLA’s option, is the
exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL
OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES,
INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED
WARRANTY. IN NO EVENT SHALL MOTOROLA BE LIABLE FOR
DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE
PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME,
NAG-LACR.book Page 55 Tuesday, March 12, 2013 3:37 PM
III. STATE LAW RIGHTS:
SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES
OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY
NOT APPLY.
A) Defects or damage resulting from use of the Product in other
than its normal and customary manner.
B) Defects or damage from misuse, accident, water, or neglect.
C)Defects or damage from improper testing, operation,
maintenance, installation, alteration, modification, or adjustment.
D)Breakage or damage to antennas unless caused directly by
defects in material workmanship.
E) A Product subjected to unauthorized Product modifications,
disassembles or repairs (including, without limitation, the addition
to the Product of non-MOTOROLA supplied equipment) which
adversely affect performance of the Product or interfere with
MOTOROLA's normal warranty inspection and testing of the
Product to verify any warranty claim.
F) Product which has had the serial number removed or made
illegible.
G)Rechargeable batteries if:
(1) any of the seals on the battery enclosure of cells are broken
or show evidence of tampering.
(2) the damage or defect is caused by charging or using the
battery in equipment or service other than the Product for which it
is specified.
H)Freight costs to the repair depot.
I) A Product which, due to illegal or unauthorized alteration of the
software/firmware in the Product, does not function in
accordance with MOTOROLA’s published specifications or the
FCC certification labeling in effect for the Product at the time the
Product was initially distributed from MOTOROLA.
This warranty gives specific legal rights, and there may be other
rights which may vary from state to state.
IV. HOW TO GET WARRANTY SERVICE:
V. WHAT THIS WARRANTY DOES NOT COVER:
You must provide proof of purchase (bearing the date of purchase
and Product item serial number) in order to receive warranty
service and, also, deliver or send the Product item, transportation
and insurance prepaid, to an authorized warranty service location.
Warranty service will be provided by MOTOROLA through one of its
authorized warranty service locations. If you first contact the
company which sold you the Product (e.g., dealer or
communication service provider), it can facilitate your obtaining
warranty service. You can also call MOTOROLA at 1-800-927-2744
US/Canada.
Limited Warranty
INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR
SAVINGS OR OTHER INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT
SUCH MAY BE DISCLAIMED BY LAW.
55
English
NAG-LACR.book Page 56 Tuesday, March 12, 2013 3:37 PM
J) Scratches or other cosmetic damage to Product surfaces that
does not affect the operation of the Product.
K) Normal and customary wear and tear.
Limited Warranty
VI. PATENT AND SOFTWARE PROVISIONS:
56
MOTOROLA will defend, at its own expense, any suit brought
against the end user purchaser to the extent that it is based on a
claim that the Product or parts infringe a United States patent, and
MOTOROLA will pay those costs and damages finally awarded
against the end user purchaser in any such suit which are
attributable to any such claim, but such defense and payments are
conditioned on the following:
A) that MOTOROLA will be notified promptly in writing by such
purchaser of any notice of such claim;
B) that MOTOROLA will have sole control of the defense of such
suit and all negotiations for its settlement or compromise; and
C)should the Product or parts become, or in MOTOROLA’s opinion
be likely to become, the subject of a claim of infringement of a
United States patent, that such purchaser will permit
MOTOROLA, at its option and expense, either to procure for
such purchaser the right to continue using the Product or parts or
to replace or modify the same so that it becomes non-infringing
or to grant such purchaser a credit for the Product or parts as
depreciated and accept its return. The depreciation will be an
equal amount per year over the lifetime of the Product or parts as
established by MOTOROLA.
for the use of ancillary equipment or software not furnished by
MOTOROLA which is attached to or used in connection with the
Product. The foregoing states the entire liability of MOTOROLA with
respect to infringement of patents by the Product or any parts
thereof.
Laws in the United States and other countries preserve for
MOTOROLA certain exclusive rights for copyrighted MOTOROLA
software such as the exclusive rights to reproduce in copies and
distribute copies of such MOTOROLA software. MOTOROLA
software may be used in only the Product in which the software was
originally embodied and such software in such Product may not be
replaced, copied, distributed, modified in any way, or used to
produce any derivative thereof. No other use including, without
limitation, alteration, modification, reproduction, distribution, or
reverse engineering of such MOTOROLA software or exercise of
rights in such MOTOROLA software is permitted. No license is
granted by implication, estoppel or otherwise under MOTOROLA
patent rights or copyrights.
MOTOROLA will have no liability with respect to any claim of patent
infringement which is based upon the combination of the Product or
parts furnished hereunder with software, apparatus or devices not
furnished by MOTOROLA, nor will MOTOROLA have any liability
English
VII. GOVERNING LAW:
This Warranty is governed by the laws of the State of Illinois, U.S.A.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Mode                       : UseOutlines
XMP Toolkit                     : 3.1-701
Create Date                     : 2013:03:12 14:47:44Z
Creator Tool                    : FrameMaker 8.0
Modify Date                     : 2013:03:12 15:53:19+08:00
Metadata Date                   : 2013:03:12 15:53:19+08:00
Copyright                       : MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. ©Motorola Solutions, Inc. All Rights Reserved.
Format                          : application/pdf
Creator                         : Motorola Solutions, Inc.
Title                           : MOTOTRBO User Guide
Producer                        : Acrobat Distiller 7.0 (Windows)
Document ID                     : uuid:4e11861e-7d22-4597-9a65-474decadaded
Instance ID                     : uuid:169495b3-8960-47f3-9d63-1c3e2cf0edc9
Page Count                      : 66
Author                          : Motorola Solutions, Inc.
EXIF Metadata provided by EXIF.tools
FCC ID Filing: AZ489FT3833

Navigation menu