Motorola Solutions 89FT3836 2-way portable radio User Manual

Motorola Solutions, Inc. 2-way portable radio

User Manual

RDU4100+, RDU4103+ & RDV5100+ Non-Display ModelsUser GuideTwo-Way Radios
Open Source Software Legal Notices:This Motorola product contains Open Source Software. For information regarding licenses, acknowledgements, required copyright notices and other usage terms, refer to the documentation for this Motorola product at:http://businessonline.motorolasolutions.comGo to: Resource Center > Product Information > Manual > Accessories.DRAFT 1
English   1CONTENTSCONTENTSContents. . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Product Safety. . . . . . . . . . . . . . . . . . . . . . . .4Introduction . . . . . . . . . . . . . . . . . . . . . . . . . .5Package Contents . . . . . . . . . . . . . . . . . . . . . .5FCC Licensing Information  . . . . . . . . . . . . .7Interference Information  . . . . . . . . . . . . . . . . .7Batteries and Chargers Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . 10Operational Safety Guidelines. . . . . . . . . . . .11Radio Overview . . . . . . . . . . . . . . . . . . . . . .12Parts Of The Radio . . . . . . . . . . . . . . . . . . . .12On/Off/Volume Knob.. . . . . . . . . . . .  . . .13Channel Selector Knob. .. . . . . . . . . . . . .13Accessory Connector . . . . . . . . . . . . . . .13Model Label . . . . . . . . . . . . . . . . . . . . . .13Microphone . . . . . . . . . . . . . . . . . . . . . . .13Antenna. . . . . . . . . . . . . . . . . . . . . . . . . .13LED Indicator . . . . . . . . . . . . . . . . . . . . .13Side Buttons . . . . . . . . . . . . . . . . . . . . . .13The Lithium-Ion (Li-Ion) Battery . . . . . . .13Battery Features . . . . . . . . . . . . . . . . . . .15About the Li-Ion Battery . . . . . . . . . . . . . 14Battery Recycling and Disposal . . . . . . . 16Installing the Lithium-Ion (Li-Ion) Battery . . . . . . . . . . . . . . . . . . . . . . . . 16Removing the Lithium-Ion (Li-Ion) Battery . . . . . . . . . . . . . . . . . . . . . . . . 17Power Supply, Adaptor and Drop-in Tray Charger . . . . . . . . . . . . . . . . . . . 19Battery Life Information . . . . . . . . . . . . . 20Charging the Battery . . . . . . . . . . . . . . . 21Drop-in Tray Charger LED Indicators . . 24Estimated Charging Time . . . . . . . . . . . 26Multi-Unit Charger LED Indicators . . . . . 27Getting Started . . . . . . . . . . . . . . . . . . . . . . 28Turning radio ON/OFF . . . . . . . . . . . . . . . . . 28Adjusting Volume . . . . . . . . . . . . . . . . . . . . . 28Selecting a Channel . . . . . . . . . . . . . . . . . . . 28Talking and Monitoring. . . . . . . . . . . . . . . . . 28DRAFT 1Canada Licensing Information. . . . . . . . . . .9General Information . . . . . . . . . . . . . . . . .. ..  9RDX+ Non Display Models . . . . . . . . . . .  . .14Attaching and Removing Antenna. . .  18Attaching the Antenna . . . .. . . . . . . .  18Removing the Antenna . . . . . . . . . . .  18Installing Spring Action Clip Belt  . . .  19
English   2CONTENTSWith Compatible VOX Accessories. . . . .32Setting VOX Sensitivity. . . . . . . . . . . . . .32Microphone Gain. . . . . . . . . . . . . . . . . . .33Hands Free without Accessories (iVOX).33 Toggle Voice Prompt in User Mode . . . .33Power Up - Tone Mode. . . . . . . . . . . . . .33Reset to Factory Defaults . . . . . . . . . . . .33Programming Features. . . . . . . . . . . . . . . .34Advanced Configuration Mode  . . . . . . . . . . .34Entering Advanced Configuration Mode . . . . . . . . . . . . . . . . . . . . . . . . . .35Entering Frequencies Values . . . . . . . . .35Reading CTCSS / DPL Values . . . . . . . .36Reading Auto-Scan Values. . . . . . . . . . .36Active Channels . . . . . . . . . . . . . . . . . . .36Weather Channel Programming Saving Settings. . . . . . . . . . . . . . . . . . . .36Programming Values Example . . . . . . . . . . .39Example of Programming a Freq uency .39Example of Programming a Code. . . . . .40Channels  . . . . . . . . . . . . . . . . . . .  . . . 41 Example of Programming WeatherChannels (Not valid for RMU4103+) . 41Other Programming Features . . . . . . . . . . . 42Scan. . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Editing Scan List . . . . . . . . . . . . . . . . . . 42Nuisance Channel Delete . . . . . . . . . . . 43Customer Programming Software (CPS) . . . 43Time-Out Timer . . . . . . . . . . . . . . . . . . . 44Power Select . . . . . . . . . . . . . . . . . . . . . 44Call Tones . . . . . . . . . . . . . . . . . . . . . . . 44Scramble . . . . . . . . . . . . . . . . . . . . . . . . 45Reverse Burst . . . . . . . . . . . . . . . . . . . . 45Text-to-Speech (Changing Pre-Defined Voice Aliases) . . . . . . . . 45Weather Feature . . . . . . . . . . . . . . . . . . . . . 47Weather Alert Mode. . . . . . . . . . . . . . . . 48EOM Enabled . . . . . . . . . . . . . . . . . . . . 49New Alert Tone Timer . . . . . . . . . . . . . . 49Event Type Filter . . . . . . . . . . . . . . . . . . 50DRAFT 1Example of Programming Auto-Scan . . .40 Example of Programming ActiveReceiving a Call . . . . . . . . . . . . . . . . . . .  . . . 29Talk Range. .  . . . . . . . . . . . . . . . . . . . . .  . . . 29Radio LED Indicators . . . . . . . . . . . . . . .  . . . 31Hands-Free Use/VOX . . . . . . . . . . . . . . . . . 32(Not for RDU 4103+). . . . . . . . . . . . . .36
English   3CONTENTSEmergency . . . . . . . . . . . . . . . . . . . . . . .51Statement . . . . . . . . . . . . . . . . . . . . . . . .51Event Code Filter . . . . . . . . . . . . . . . . . .51Block Event. . . . . . . . . . . . . . . . . . . . . . .52Event Code . . . . . . . . . . . . . . . . . . . . . . .52The Critical Events Table . . . . . . . . . . . .52Geographic Filter . . . . . . . . . . . . . . . . . .53Cloning Radios . . . . . . . . . . . . . . . . . . . . . . .55Cloning with a Multi Unit Charger (MUC) . . . . . . . . . . . . . . . . . . . . . . . . .55Cloning Radio using the Radio to Radio (R2R) Cloning Cable (Optional Accessory). . . . . . . . . . . . . .57Cloning using the Customer Programming Software (CPS) . . . . . .59Troubleshooting . . . . . . . . . . . . . . . . . . . . .60Use and Care . . . . . . . . . . . . . . . . . . . . . . . .64Frequency and Code Charts  . . . . . . . . . . .65RDV5100+ – VHF Default Frequencies Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66RDX+ UHF Frequencies Chart . . . . . . . . . . .67RDU4100+ – UHF Default Frequencies Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70CTCSS and PL/DPL Codes . . . . . . . . . . . . . 72Motorola Limited Warranty for the United States and Canada. . . . . . . . . . . . . 78Accessories . . . . . . . . . . . . . . . . . . . . . . . . 82Audio Accessories . . . . . . . . . . . . . . . . . . . . 82Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83Chargers . . . . . . . . . . . . . . . . . . . . . . . . . . . 83Carry Accessories . . . . . . . . . . . . . . . . . . . . 83Software Applications. . . . . . . . . . . . . . . . . . 83DRAFT 1All Events. . . . . . . . . . . . . . . . . . . . . . . . 50Alert Test Event . . . . . . . . . . . . . . . . . . . 50Warning . . . . . . . . . . . . . . . . . . . . . . . . . 50Watch. . .  . . . . . . . . . . . . . . . . . . . . .  . . . 51RDU4103+ – UHF Default FrequenciesChart . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  71Power Supplies AC Pin Adaptors. . . . . . . . . 83Power Supplies. . . . . . . . . . . . . . . . . . . . . . . 84Antennas. . . . . . . . . . . . . . . . . . . . . . . . . . . . 82Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
English   4PRODUCT SAFETYPRODUCT SAFETYPRODUCT SAFETY AND RFEXPOSURE COMPLIANCEATTENTION!This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. For a list of Motorola-approved antennas, batteries and other accessories, visit the following website which lists approved accessories:www.motorolasolutions.com/RDXBefore using this product, read the operating instructions and RF energy awareness information contained in the Product Safety and RF Exposure booklet enclosed with your radio.!C a u t i o nDRAFT 1
English   5INTRODUCTIONINTRODUCTIONThank you for purchasing the Motorola® RDX Series™ Radio. This radio is a product of Motorola's 80 plus years of experience as a world leader in the designing and manufacturing of communications equipment. The  RDX  Series™  radios  provide  cost effective communications for businesses such as retail stores, restaurants, schools, construction sites, manufacturing, property and hotel management and more. Motorola professional two-way radios are the perfect communications solution for all of today's fast-paced industries.Note: Read this user guide carefully to ensure you know how to properly operate the radio before useBusiness Radios, Mailstop 1C15, Motorola8000 West Sunrise BoulevardPlantation, Florida 33322PACKAGE CONTENTS• Radio•Belt Clip• Lithium-Ion Battery• Power Supply• Quick Reference Guide• Warranty Card• Drop-in Tray Charger• Product Safety & RF Exposure BookletDRAFT 1•UHF or VHF Antenna (Depending on Model)
English   6INTRODUCTIONFor a copy of a large-print version of this user guide or for product-related questions, contact1-800-448-6686 in the USA1-800-461-4575 in Canada1-888-390-6456 on TTY (Text Telephone)For product related information, visit us at:www.motorolasolutions.com/RDXDRAFT 1
FCC LICENSING INFORMATIONEnglish   7FCC LICENSING INFORMATIONINTERFERENCE INFORMATIONOperation is subject to the condition that this device does not cause harmful interference.RDX Series™ Business two-way radios operate on  radio  frequencies  that  are  regulated  by  the Federal Communications Commission (FCC). To transmit on these frequencies, you are required to have a license issued by the FCC. Application is made available on FCC Form 601 and Schedules D, H, and Remittance Form 159.To obtain these FCC forms, request document 000601 which includes all forms and instructions. If you wish to have the document faxed, mailed or have questions, use the following contact information.Faxed contact the Fax-On- Demand system at:Mailed call the FCC forms hotline at: Questions regarding FCC license contact the FCC at:1-202-418-0177 1-800-418-FORM1-800-418-36761-888-CALL-FCC1-888-225-5322Or: http://www.fcc.govDRAFT 1
English   8FCC LICENSING INFORMATIONBefore filling out your application, you must decide which frequency(ies) you can operate on. See “Frequencies and Code Charts”. For questions on determining the radio frequency, call Motorola Product Services at: 1-800-448-6686Changes or modifications not expressly approved by Motorola may void the user’s authority granted by the FCC to operate this radio and should not be made. To comply with FCC requirements, transmitter adjustments should be made only by or under the supervision of a person certified as technically qualified to perform transmitter maintenance and repairs in the private land mobile and fixed services as certified by an organization representative of the user of those services. Replacement of any transmitter component (crystal, semiconductor, etc.) not authorized by the FCC equipment authorization for this radio could violate FCC rules.Use of this radio outside the country where it was intended to be distributed is subject to government regulations and may be prohibitedDRAFT 1
English   9CANADA LICENSING INFORMATIONCanada Lisencing InformationGENERAL INFORMATIONThe operation of your Motorola radio is subject to the Radiocommunications Act and must comply with rules and regulations of the Federal Government’s department of Industry Canada. Industry Canada requires that all operators using Private Land Mobile frequencies obtain a radio license before operating their equipment.An application for your Industry Canada license is made on the form included with your radio. Additional forms and latest license application versions can be obtained from the nearest Industry Canada District office. A list of these offices is included for your information.THE LICENSE APPLICATIONGeneral Instructions1. Fill in the items as per the instructions. If you need additional space for any item use the reverse side of the application.2. Be sure to use a typewriter or print legibly.3. Make a copy for your files.4. Prepare a cheque or money order made out tothe “Receiver General for Canada”, for an amount, which is on the following schedule, for each radio purchased. (License is valid until April 1st of each year, and the renewed. 5. Mail your completed application, along with your cheque or money order to the closest IndustryCanada District office, according to the list on pagesTo obtain the latest Canadian License Application form, please go to:www.ic.gc.ca
English10BATTERIES AND CHARGERS SAFETY INFORMATIONBATTERIES AND CHARGERS SAFETY INFORMATIONThis document contains important safety and operating instructions. Read these instructions carefully and save them for future reference. Before using the battery charger, read all the instructions and cautionary markings on• the charger, • the battery, and • the radio using the battery1. To reduce risk of injury, charge only the rechargeable Motorola-authorized batteries. Other batteries may explode, causing personal injury and damage. 2. Use of accessories not recommended by Motorola may result in risk of fire, electric shock, or injury. 3. To reduce risk of damage to the electric plug and cord, pull by the plug rather than the cord when disconnecting the charger. 4. An extension cord should not be used unlessabsolutely necessary. Use of an improper extension cord could result in risk of fire and electric shock. If an extension cord must beused, make sure that the cord size is 18AWG for lengths up to 100 feet (30.48 m), and16AWG for lengths up to 150 feet (45.72 m). 5. To reduce risk of fire, electric shock, or injury, donot operate the charger if it has been broken or damaged in any way. Take it to a qualified Motorola service representative. 6. Do not disassemble the charger; it is not repairable and replacement parts are not available. Disassembly of the charger may result in risk of electrical shock or fire. 7. To reduce risk of electric shock, unplug the charger from the AC outlet before attempting any maintenance or cleaningDRAFT 1
English   11BATTERIES AND CHARGERS SAFETY INFORMATIONOPERATIONAL SAFETY GUIDELINES • Turn the radio OFF when charging battery. • The charger is not suitable for outdoor use. Use only in dry locations/conditions. • Connect charger only to an appropriately fused and wired supply of the correct voltage (as specified on the product). • Disconnect charger from line voltage by removingmain plug. • The outlet to which this equipment is connected should be nearby and easily accessible. • In equipment using fuses, replacements must comply with the type and rating specified in the equipment instructions. • Maximum ambient temperature around the power supply equipment must not exceed 40°C (104°F). • Power output from the power supply unit must not exceed the ratings stated on the product label located at the bottom of the charger. • Make sure that the cord is located where it will not be stepped on, tripped over, or subjected to water, damage, or stress. DRAFT 1
English  12RADIO OVERVIEWRADIO OVERVIEWPARTS OF THE RADIOAntennaMicrophoneOn/Off/Volume KnobLED IndicatorSB2 - Scan/Nuisance Channel DeleteSB1 - Monitor ButtonBatteryModel LabelPTT (Push-To-Talk) ButtonChannel Selector KnobAudio Accessory 2 Pin ConnectorRDU4100+DRAFT 1
English   13RADIO OVERVIEWOn/Off/Volume KnobUsed to turn the radio ON or OFF and to adjust the radio’s volume.Channel Selector KnobUsed to switch the radio to different channels.Accessory ConnectorUsed to connect compatible audio accessories.Model LabelIndicates the model of the radio.MicrophoneSpeak clearly into the microphone when sending a message.AntennaFor models RDU4100+ and RDU4103+ there are 2 removable antennas . For RDV5100+ there is one VHF removable antenna.  LED IndicatorUsed to give battery status, power-up status, radio call information and scan status.Side ButtonsPush-to-Talk (PTT) Button• Press and hold down this button to talk, release it to listen.Side Button 1 (SB1)• The Side Button 1 is a general button that can be configured by the Customer Programming Software - CPS. The default setting of SB1 is ‘Monitor’.Side Button 2 (SB2)• The Side Button 2 is a general button that can be configured by the CPS. The SB2 default setting is ‘Scan/Nuisance Channel Delete’.The Lithium-Ion (Li-Ion) BatteryRDX Series comes with a Standard Capacity Li-Ion battery. Other batteries may be available. For more information, see “Battery Features” on page 15.DRAFT 1
English  14RADIO OVERVIEWThis User Guide covers multiple RDX Series models, and may detail some features your radio does not have. The radio’s model is shown on the bottom of the radio and provides the following information: Table 1: RDX Series Radio SpecificationsModel Frequency BandTransmit Power (Watts)Number of Channels AntennaRDU4100+ UHF 410 RemovableRDU4103+VHF410 RemovableDRAFT 1RDV5100+UHF510RemovableRDX+ Non Display Models
English   15RADIO OVERVIEWBATTERY FEATURESRDX Series radios provide Lithium-Ion batteries that come in different capacities that defines the battery life.About the Li-Ion BatteryThe RDX Series radio comes equipped with a rechargeable Li-Ion battery. This battery should be fully charged before initial use to ensure optimum capacity and performance. Battery life is determined by several factors. Among the more critical are the regular overcharge of batteries and the average depth of discharge with each cycle. Typically, the greater the overcharge and the deeper the average discharge, the fewer cycles a battery will last. For example, a battery which is overcharged and discharged 100% several times a day, lasts fewer cycles than a battery that receives less of an overcharge and is discharged to 50% per day. Further, a battery which receives minimal overcharging and averages only 25% discharge, lasts even longer.Motorola batteries are designed specifically to be used with a Motorola charger and vice versa. Charging in non-Motorola equipment may lead to battery damage and void the battery warranty. The battery should be at about 77°F (25°C) (room temperature), whenever possible. Charging a cold battery (below 50° F [10°C]) may result in leakage of electrolyte and ultimately in failure of the battery. Charging a hot battery (above 95°F [35°C]) results in reduced discharge capacity, affecting the performance of the radio. Motorola rapid-rate battery chargers contain a temperature-sensing circuit to ensure that batteries are charged within the temperature limits stated above. DRAFT 1
English  16RADIO OVERVIEWBattery Recycling and DisposalLi-Ion rechargeable batteries can be recycled. However, recycling facilities may not be available in all areas. Under various U.S. state laws and the laws of several other countries, batteries must be recycled and cannot be disposed of in landfills or incinerators. Contact your local waste management agency for specific requirements and information in your area. Motorola fully endorses and encourages the recycling of Li-Ion batteries. In the U.S. and Canada, Motorola participates in the nationwide Rechargeable Battery Recycling Corporation (RBRC) program for Li-Ion battery collection and recycling. Many retailers and dealers participate in this program. For the location of the drop-off facility closest to you, access RBRC's Internet web site at:www.rbrc.com or call: 1-800-8-BATTERYThis internet site and telephone number also provides other useful information concerning recycling options for consumers, businesses and governmental agencies.DRAFT 1
RADIO OVERVIEWEnglish   17Installing the Lithium-Ion (Li-Ion) Battery1. Turn OFF the radio.2. With the Motorola logo side up on the battery pack, fit the tabs at the bottom of the battery into the slots at the bottom of the radio’s body.3. Press the top part of the battery towards the radio until a click is heard.Note: To learn about the Li-Ion Battery Life features, refer to “About the Li-Ion Battery” on page 14Removing the Lithium-Ion (Li-Ion) Battery1. Turn OFF the radio.2. Push down the battery latch and hold it depressed while removing the battery.3. Pull the battery away from the radio.Battery LatchslotsBattery Latch
RADIO OVERVIEWEnglish   18Attaching and Removing AntennaAttaching the Antenna1. Align the threaded end of the antenna with the radio’s antenna connector.2. Turn the antenna clockwise to fasten it.Removing the Antenna1. Turn the antenna counterclockwise until you can remove it.These instructions apply ONLY to models RDU4100 and RDV5100. Do not attempt to remove the antenna if your radio is not one of these models.
RADIO OVERVIEWEnglish  19Installing Spring Action Belt Clip1. Slide the spring action belt clip rails into the belt clip grooves on the back of the battery pack and slide it down until the belt clip tab snaps into place.2. To remove, pull back the metal release tab on the belt clip tab and push the spring action belt clip upward to remove.Power Supply, Adaptor and Drop-in Tray ChargerThe radio is equipped with one Drop-in Tray Charger and one Power Supply with Adaptor. For details, see “Chargers” on page 83.Belt Clip TabSpring Action Belt ClipDrop-in Tray ChargerPower Supply
RADIO OVERVIEWEnglish   20Battery Life InformationWhen the Battery Save feature is ON (enabled by default) the battery life will be longer. The following chart summarizes battery life estimations:Li-Ion Battery Life with Battery Save feature ONBattery Type 5 Watts 4 Watts 2 WattsStandard Capacity 8.5 hours 8.5 hours 12 hoursHigh Capacity 18.5 hours 18.5 hours 26 hoursNote: Battery life is estimated based on 5% transmit/ 5% receive/ 90% standby standard duty cycle
RADIO OVERVIEWEnglish   21Charging the BatteryRDX Series™ offers two types of chargers :• Standard Charger and,• Rapid Charger.Note: The radio comes equipped with a Standard ChargerTo charge the battery (with the radio attached), place it in a Motorola-approved Drop-in Tray Single Unit Charger or Drop-in Tray Multi Unit Charger.Note: When acquiring additional chargers or power supplies, make sure you have similar drop-in tray chargers and power supplies sets (all “rapid” or all “standard”). For part number details, refer to “Chargers” on page 81Charging with the Drop-in Tray Single Unit Charger (SUC)1. Place the drop-in tray charger on a flat surface.2. Insert the connector of the power supply into the port on the side of the drop-in tray charger.3. Plug the AC adaptor into a power outlet. 4. Insert the radio into the tray with the front of the radio facing the front of the charger, as shown. Note: When charging a battery attached to a radio, turn the radio OFF to ensure a full charge. See “Operational Safety Guidelines” on page 8 for more informationPower Supply(Transformer) Drop-in Tray ChargerDrop-in TrayCharger Port
RADIO OVERVIEWEnglish  22Charging a Standalone BatteryTo charge only the battery - at step 4, insert the battery into the tray, with the inside surface of the battery facing the front of the charger, as shown. Ensure the slots in the battery correctly engage in the chargerNote: Ensure that the bracket in the charger is adjusted to the correct position for either Standard or High capacity battery. See “Charging a Standard Battery” on page 22Charging a Standard BatteryThe drop-in tray charger has a removable bracket that is adjustable depending on the type of battery that needs to be charged. It is designed to charge either the battery (with the radio) or a standalone battery. The drop-in tray charger's default position will charge a standard battery. The following image shows the orientation for each battery:Figure 1:    Identifying the Drop-In Charger’s Position Before Charging the BatteryAdjustable bracketStandard  High and Ultra High CapacityAdjustable bracket
RADIO OVERVIEWEnglish   23Charging a High Capacity   BatteryTo convert the charger from the default setup to accommodate the High capacity or Ultra High capacity battery:1. Squeeze both tabs on each side of the removable bracket in the drop-in charger tray and lift the bracket from the charger tray.2. Rotate the removable bracket 180 degrees and replace it by fitting it in the charger slot until it snaps. The label on the removable bracket should show ‘High Capacity Battery’ facing front of the charger.3. Repeat same procedure to return to the charging a Standard Battery position. Label on the removable bracket should show ‘StandardBattery’ facing front.Note: Make sure the bracket is assembled correctly for both standalone battery and battery (with radio)RemovablePieceRemovablePieceTurn aroundhorizontal180 degree
RADIO OVERVIEWEnglish  24Drop-in Tray Charger LED IndicatorsStandard Charger LED IndicatorStatus  LED Status  CommentsPower ON Steady red indication for 3 seconds The charger has powered upCharging Blinking red (slow) The charger is currently chargingCharging Complete Steady red indication  Battery is fully chargedBattery Fault(*) Blinking red (fast) Battery had a fault when battery was insertedNotes:• (*) Normally re-seating the battery pack will correct this issue. • (**) Battery temperature is too warm or too cold or wrong power supply is being used
RADIO OVERVIEWEnglish   25Rapid Charger LED Indicator Status   LED Status   Comments Power ON Steady green indication for 3 seconds The charger has powered upCharging Blinking green The charger is currently chargingTop-off Charging Blinking green (slow) Battery is near fully chargedCharge Complete Steady green indication Battery is fully chargedBattery Fault (*) Blinking red (fast) Battery has a fault when battery was insertedWaiting to Charge (**)Double-blink yellow indications Battery charging conditions not suitableNotes:• (*) Normally re-seating the battery pack will correct this issue. • (**) Battery temperature is too warm or too cold or wrong power supply is being used
RADIO OVERVIEWEnglish  26Estimated Charging TimeThe following table provides the estimated charging time of the battery. For further details, see “Battery” on page 82.Estimated Charging TimeCharging SolutionBattery TypeStandard High CapacityStandard Charging Solution  7 hours 12 hoursRapid Charging Solution 1.5 hours 3 hours
RADIO OVERVIEWEnglish   27Charging a Radio and Battery using a Multi Unit Charger- MUC (Optional Accessory)The Multi Unit Charger (MUC) allows drop-in charging of up to 6 radios or batteries. Batteries can be charged with the radios or removed and placed in the MUC separately. Each of the 6 charging pockets can hold a radio or battery, but not both.1. Place the charger on a flat surface.2. Insert the power cord plug into the MUC’s jack.3. Plug the cord into an AC outlet.4. Turn the radio OFF.5. Set removable bracket for battery type.6. Insert the radio or battery into the charging pocket.Notes:•This Multi Unit Charger also allows you to cloneup to 3 radios (3 Source radios and 3 Target radios). Refer to page 55 for details.• Further details on MUC’s operation are explained in the Instructions Sheet provided with the MUC. For part number details, refer to the Accessories section. MUC LED IndicatorStatus LED Status CommentsCharging Steady Red IndicationThe charger is currently chargingCharge CompleteSteady Green IndicationBattery is fully chargedBattery Fault (*)Blinking red (fast)Battery was faulty when insertedNote: (*) Normally re-seating the battery pack will correct this issue.
English   28GETTING STARTEDGETTING STARTEDFor the following explanations, refer to “Parts Of The Radio” on page 12.TURNING RADIO ON/OFF To turn ON the radio, rotate the On/Off/Volume Knob clockwise. The radio plays one of the following:• Power up tone and channel number announcement, or• Battery level and channel number announcements, or• Silent (Audible tones disabled)The LED blinks red briefly.To turn the radio OFF, rotate the On/Off/Volume Knob counterclockwise until you hear a ‘click’ and the radio LED Indicator turns OFF.ADJUSTING VOLUME Turn the On/Off/Volume Knob clockwise to increase the volume, or counterclockwise to decrease the volume.Note: Do not hold the radio too close to the ear when the volume is high or when adjusting the volumeSELECTING A CHANNEL To select a channel, turn the Channel Selector Knob until you reach the desired channel. An audible voice indicates the selected channel. Each channel has its own Frequency, Interference Eliminator Code and Scan Settings.TALKING AND MONITORING It is important to monitor for traffic before transmitting to avoid ‘talking over’ someone who is already transmittingTo monitor, long press and hold the SB1(*) button to access channel traffic. If no activity is present, you will hear ‘static’. To release, press SB1 again. Once channel traffic has cleared, proceed with your call by pressing the PTT button. When transmitting, the LED Indicator stays solid red.DRAFT 1
English  29GETTING STARTEDNotes:• To listen to all activity on a current channel, short press the SB1 to set the CTCSS/DPL code to 0. This feature is called ‘CTCSS/DPL Defeat (Squelch set to SILENT)’.• (*) This assumes SB1 is not being programmed for a different mode. RECEIVING A CALL1. Select a channel by rotating the Channel Selector Knob until you reach the desired channel. An audible voice indicates the selected channel.2. Make sure the PTT button is released and listen for voice activity.3. The LED Indicator stays solid red when the radio is receiving a call.4. To respond, hold the radio vertically 1 to 2 inches (2.5 to 5cm) from mouth. Press the PTT button to talk; release it to listen.TALK RANGEDRAFT 1TALK RANGE ModelIndustrial Multi-LevelInside steel/concrete Industrial buildingsInside multi-level buildingsUHF 4W Up to 350,000 Sq. Ft.  Up to 30 Floors  VHF 5W  Up to 300,000 Sq. Ft.  Up to 18 Floors
English   30GETTING STARTEDTo establish a proper two-way communication, the channel, frequency, and interference eliminator codes must be the same on both radios. This depends on the stored profile that has been preprogrammed on the radio:1. Channel: Current channel that the radio isusing, depending on radio model.2. Frequency: The frequency the radio uses to transmit/receive.3. Interference Eliminator Code: These codes help minimize interference by providing a choice of code combinations.4. Scramble Code: Codes that make the transmissions sound garbled to anyone listening who is not set to that specific code.5. Bandwidth: Some frequencies have selectable channel spacing, which must match other radios for optimum audio quality.For details on how to set up frequencies and CTCSS/DPL codes in the channels, refer to “Advanced Configuration Mode” on page 32.DRAFT 1
English  31GETTING STARTEDRADIO LED INDICATORSRADIO STATUS LED INDICATIONChannel Busy Solid OrangeCloning Mode  Double Orange HeartbeatsCloning In Progress  Solid OrangeFatal Error at Power up  One Green Blink, One Orange Blink, One Green Blink, then repeat for 4 secondsLow Battery  Orange HeartbeatLow Battery Shutdown  Fast Orange HeartbeatMonitor  LED is OFFPower-Up  Solid Red for 2 seconds‘Idle’ Programming Mode /Channel Mode  Green HeartbeatScan Mode  Fast Red HeartbeatTransmit (Tx)/Receive (RX)  Solid RedTransmit in Low Power Select  Solid Orange VOX/iVOX Mode Double Red HeartbeatsDRAFT 1
English   32GETTING STARTEDHANDS-FREE USE/VOXMotorola RDX Series™ radios can operate hands-free (VOX) when used with compatible VOX accessories. With Compatible VOX AccessoriesThe default factory setting for VOX sensitivity level is OFF (level ‘0’). Before using VOX, set VOX level to a level different from ‘0’ via the Customer Programming Software (CPS). Then, perform the following steps:1. Turn the radio OFF.2. Open accessory cover.3. Insert the audio accessory’s plug firmly intoaccessory port.4. Turn radio ON. The LED Indicator will blink double red5. Lower radio volume BEFORE placing accessory near ear.6. To transmit, speak into accessory microphone and to receive, stop talking.7. VOX can be temporarily disabled by pressing the PTT button or by removing the audio accessory.Note: To order accessories, refer to: www.motorolasolutions.com/RDX, call 1 (800) 448-6686, or contact your Motorola point of purchaseSetting VOX SensitivityThe sensitivity of the radio's accessory or microphone can be adjusted to suit different operating environments. VOX sensitivity can be programmed via the CPS. VOX AccessoryAccessory Port/ConnectorDRAFT 1
English  33GETTING STARTEDDefault value is OFF. If you want to use the VOX feature, VOX level should be set at a different level.• 1 = High audio input level will trigger the Tx• 2 = Medium sensitivity• 3 = Low audio input level will trigger the TxMicrophone GainThe sensitivity of the microphone can be adjusted to fit different users or operating environments.This feature can be adjusted only through the CPS. Microphone default setting is set to level 2 (medium gain).Hands Free without Accessories (iVOX)• Enable iVOX by pressing the PTT Button while turning ON the radio.• A short press of the PTT Button re-enables iVOX.• There is a short delay between the time when you start talking and when the radio transmits.Toggle Voice Prompt in User ModeShort press the SB1 Button while turning ON the radio to enable/disable the Voice Prompt in User Mode. (Default is set to ON).Note: This setting is set to OFF by default and must be enabled using the CPS.Power Up - Tone ModeTo enable/disable power up tone mode, press SB1 and SB2 buttons simultaneously for 2-3 seconds while powering up the radio until you hear the pre-programmed power up tone. 3 different power-up tones are available.Reset to Factory DefaultsReset to Factory Defaults will set back all radio features to the original factory default settings. To do so, press PTT, SB2 and SB1 simultaneously while turning ON the radio until you hear a high tone chirp. DRAFT 1
English   34PROGRAMMING FEATURESPROGRAMMING FEATURESTo easily program all the features in your radio, it is recommended to use the Customer Programming Software (CPS) and the programming cable.CPS software download is available for free at www.motorolasolutions.com/RDX.ADVANCED CONFIGURATION MODEAdvanced Configuration is a configuration mode that allows the customization of additional features via the radio’s front panel.For non-display model radios, the navigation is guided by an audible voice prompt.When the radio is set to Advanced Configuration, you are able to read and modify four features:• Frequency Selection, • Codes (CTCSS/DPL), • Auto-Scan,• Active Channels, and• Enable/Disable/Program the Weather ChannelThe Frequencies Select feature allows you to choose frequencies from a pre-defined list.The Interference Eliminator Code (CTCSS/DPL) helps minimize interference by providing you with a choice of code combinations that filter out static, noise, and unwanted messages. The Auto-Scan feature allows you to set a particular channel to automatically enable Scan each time you switch to that channel.The Active Channels feature allows you to increase or decrease the amount of active channels (In the range of maximum channels allowed).The Weather Programming feature allows you to alternate the channel function between 2 way radio channel and weather channel. There DRAFT 1
English  35PROGRAMMING FEATURESare 7 received frequencies available for this feature. Feature not available for RDU4103Entering Advanced Configuration ModeNote: Before configuring the features, make sure your radio is set to the channel you wish to program. You can do so before entering Advanced Configuration Mode or at any time during the Advanced Configuration Mode by rotating the Channel Selector Knob until you reach the desired channel.To read or modify Frequencies, Codes, Auto-Scan, Active Channels and Weather Channel set the radio to ‘Advanced Configuration Mode’ by long pressing both the PTT and the SB1 button simultaneously for 3 to 5 seconds while turning ON the radio until you hear an audible voice saying “Programming Mode” and “Channel Number”. The LED Indicator starts blinking a green heartbeat.Note: ‘Idle’ Programming Mode is the stage in the Programming Mode where the radio waits for the user to start the radio programming cycle.Once you are in the ‘Idle’ Programming Mode, you will be able to hear the Frequencies, Codes, Auto-Scan, Active Channels and Weather Channel settings by short pressing the PTT button to navigate along the different programmable features.Entering Frequencies ValuesRDU4100 has 89 frequencies, 27 frequencies for RDV5100 and 2 for RDU4103.In ‘Idle’ Programming mode, the Channel number becomes the first changeable value. Select the desired channel by turning the Channel Selector Knob. An audible voice indicated the selected channel to configure. Short pressing the PTT button allows you to cycle through the other features available for configuration. Use the SB1 and SB2 button to change the values. An audible voice indicates the value selected.DRAFT 1
English   36PROGRAMMING FEATURESReading CTCSS / DPL ValuesCycle through the features available for configuration by short pressing the PTT button until you hear the current code. The radio moves to the programming CTCSS/PL codes mode. Enter a new code value using the SB1 and SB2 buttons.The RDX Series radios have up to 219 codes available. For more information, refer to “Frequency and Code Charts” on page 64.Reading Auto-Scan ValuesAfter hearing the CTCSS/DPL codes, short pressing the PTT button moves you to Auto-Scan mode.Auto-Scan has only two values:• Enabled• DisabledActive ChannelsWhile in Auto-Scan mode, short pressing the PTT button shifts the radio to ‘Active Channels’ feature.Modify the amount of channels available using the SB1 and SB2 buttons.Weather Channel Programming (Not for RDU4103+)After setting the amount of Active Channels, short pressing the PTT button moves you to Weather Channel feature.Use the SB1 and SB2 buttons to Enable/Disable the feature.Saving SettingsOnce you are satisfied with the settings, you can either:•short press the PTT button to continue programming,•long press the PTT button to save and return to‘Idle’ Programming Mode, or• long press the PTT button twice to exit ‘Idle’DRAFT 1
English  37PROGRAMMING FEATURESProgramming Mode and return to the normal radio operation.Note:• To exit the programming mode without saving, turn OFF the radio.• If you ‘roll-over’ to the beginning of ‘Idle’ Programming Mode, you will hear “Channel Number” and the LED Indicator blinks green again. All changed values will be automatically saved.DRAFT 1
English   38PROGRAMMING FEATURESProgramming Mode FAQ1. I got distracted while programming and forgot which feature I was programming. What should I do?Return to ‘Idle’ Programming Mode and start over. You will not be able to return to Programming Mode (the radio does not provide further way to let you know the specific stage you are at in the Programming Mode). Therefore you can:• Long press the PTT button. The radio will return to ‘Idle’ Programming Mode or,•Turn OFF the radio and enter Programming Mode again. (Refer to “Entering Advanced Configuration Mode” on page 35 for more information)2. I am trying to program a frequency (or a code)value but the radio would not do it. It rolled overand took me back to value ‘0’.The radio disallow you to program any value that is not available in the frequencies and codes pool. For example, if you try to program code 220, the radio would not accept it as the maximum value allowed is 219. Same goes for the frequencies. Refer to the“Frequency and Code Charts” on page 65 to make sure you are programming a valid value.3. I am trying to enter the Programming Mode butthe radio would not do it.The radio may be locked using the CPS to disallow Front Panel Programming. To re-enable, use the CPS.4. I programmed the wrong value when I was programming. How can I erase or re-program the value?If you programmed the wrong value, you can either:• ‘Roll-over’ the radio. The radio ‘roll-over’ each time it reaches the maximum value allowed. Keep increasing (short press the SB1 button) or decreasing (short press the SB2 button) until you get the desired value or,DRAFT 1
English  39PROGRAMMING FEATURES• Turn OFF the radio and start over.5. I just programmed the value I wanted. How do I exit the Programming Mode?You can either:• long press the PTT button twice to exit if you’re in the Programming Mode or,• Long press the PTT button once if you are already in the ‘Idle’ Programming mode.6. I am done programming the features in this channel. How do I program another channel?Short press the PTT button several times until you hear “Channel Number”. Switch channel by rotating the Channel Selector Knob. If you wish to save the changes, make sure you are in the ‘Idle’ Programming Mode before switching the channel, otherwise you will lose the changes made.PROGRAMMING VALUES EXAMPLEExample of Programming a FrequencyAssuming current frequency value is set to Channel 1, with the UHF default frequency set to ‘02’ (equivalent to 464.5500 MHz), and you want to change it to Frequency Number = ‘13’ (which is mapped to 461.1375 MHz), follow this sequence:1. Enter Advanced Configuration Mode.2. Short press the PTT button to enter Frequency Mode. The radio audible voice announces that the current value is ‘2’.3. Press the SB1 button eleven times to increase frequencies and you will hear frequency “One, three” (13).4. Long press the PTT button. LED Indicator shows a green heartbeat to indicate ‘Idle’ Programming Mode.5. Long press the PTT button again to exit Programming Mode or turn OFF the radio.DRAFT 1
English   40PROGRAMMING FEATURESExample of Programming a CodeAssuming the current code value is set to factory default ‘001’, and you want to change it to CTCSS/DPL Code = 103. Follow the sequence indicated below:1. Enter Advanced Configuration Mode.2. Short press the PTT button twice. The radioaudible voice announced “Code Number” (Entering CTCSS/DPL Programming Selection Mode).3. Pressing and holding SB1 or SB2 button fast forwards / rewinds the value at the nearest 10’s. When released, the radio audible voice announces the first, second and third digit in full. Keep pressing the SB1 or SB2 button several times until you hear “103”. 4. Long press the PTT button. LED Indicator shows a green heartbeat to indicate ‘Idle’ Programming Mode.5. Long press the PTT button again to exit Programming Mode or turn OFF the radio.Example of Programming Auto-ScanAuto-Scan is the third available feature in the Programming Mode and can be set to either ON or OFF on a particular channel.To set Auto-Scan to ON:• Enter Advanced Configuration Mode and select the desired channel.• Short press the PTT button three times to enter the Active Channels Programming Selection Mode. The audible voice in the radio announces “Auto-Scan” and the setting (Enabled or Disabled).• To change the setting, press SB1 or SB2.• Long press the PTT button. LED Indicator shows a green heartbeat to indicate ‘Idle’ Programming Mode.• Long press the PTT button again to exit Programming Mode or turn OFF the radio.DRAFT 1
English  41PROGRAMMING FEATURESExample of Programming Active ChannelsActive Channels is the fourth Programming Mode. It allows you to modify the number of active channels the radio is programmed to support.To set Active Channels:•Enter Advanced Configuration Mode andselect the desired channel.• Short press the PTT button four times to enter the Active Channels Programming Selection Mode. The audible voice in the radio announces “Active Channels” and the current value.• Short press the SB1 or SB2 button until you get the number of channels desired.• Long press the PTT button. LED Indicator shows a green heartbeat to indicate ‘Idle’ Programming Mode.• Long press the PTT button to exit Programming Mode or turn OFF the radio.Example of Programming Weather Channels (Not valid for RMU4103+)Weather Channels is the last Programming mode. It allows you to toggle a radio channel between 2 way radio mode and weather alert mode.To set channels to Weather Alert Mode:•Enter Advanced Configuration Mode and select the desired channel.•Short press the PTT button five times to enter the Weather Channels Programming Mode.••Short press the SB1 or SB2 button to enable/disable the feature.•Long  press  the  PTT  button.  LED  Indicator shows  a  green  heartbeat  to  indicate  ‘Idle’ Programming Mode.• Long press the PTT button again to exit Programming mode or turn OFF the radio.DRAFT 1An audible voice announces "Weather Channel and Frequency Used" and instructions on how to change values. Refer to "Weather Channel Frequencies Table" on page 48 for the frequency table.
English   42PROGRAMMING FEATURESOTHER PROGRAMMING FEATURESScanScan allows you to monitor other channels to detect conversations. When the radio detects a transmission, it stops scanning and goes to the active channel. This allows you to listen and talk to people in that channel without having to change channel manually. If there are transmissions on another channel, you will not hear that activity once the radio has stopped scanning. Once the activity on transmitting channel stops, the radio waits for 5 seconds before resuming scan again.• To start scanning, press the SB1 or SB2 buttonNote: Scan has to be programmed either to SB1 or SB2 button via CPS. SB2 is by default Scan/Nuisance Channel delete button.• To stop scanning, short press the SB1 or SB2 button (programmed for scan) again.• By pressing the PTT button while the radio is scanning, the radio will transmit on the channel which was previously selected before Scan is activated. If no transmission occurs within 5 seconds, scanning resumes.• If you want to scan a channel without the Interference Eliminator Codes (CTCSS/DPL), set the code settings for the channels to ‘0’ in the CTCSS/DPL Programming Selection Mode.Note: Whenever the radio is set to Scan, the LED Indicator blinks a Red Heartbeat.Editing Scan ListScan List can be edited by using the CPS. For more information refer to “Customer Programming Software (CPS)” on page 43.DRAFT 1
English  43PROGRAMMING FEATURESNuisance Channel DeleteNuisance Channel Delete allows you to temporarily remove channels from the Scan List. This feature is useful when irrelevant conversations on a ‘nuisance’ channel ties up the radio’s scanning feature.To delete a channel from the Scan List:• Start Scan mode by short pressing the SB1 or SB2 (programmed for scan) button.• Wait until the radio stops at the channel you wish to eliminate. Long press the SB2 button to delete it. You cannot delete the channel with scan enabled (home channel).• The channel will not be scanned again until you exit the Scan mode by short pressing the SB1 orSB2 (programmed for scan) button again or by turning OFF the radio and back ON.CUSTOMER PROGRAMMING SOFTWARE (CPS)Figure 1:    Setting up the radio to the CPSThe easiest way to program or change features in your radio is by using the Customer Programming Software (CPS) and the CPS Programming Cable(*). CPS Software is available for free as web based downloadable software at:www.motorolasolutions.com/RDXDrop-In Tray Charger TrayRadio to be programmedUSB PortsCPS Programming CableDRAFT 1
English   44PROGRAMMING FEATURESTo program, connect the RDX Series radio via the Drop-in Charger Tray and CPS Programming Cable as shown in Figure 1 on page 41. Toggle the cable switch of the CPS Programming Cable to ‘CPS Mode’.CPS allows you to program frequencies, PL/DPL Codes as well as other features such as: Bandwidth Select, Time-out Timer, Power Select, Scan List, Call Tones, Scramble, Reverse Burst, etc. CPS is a very useful tool as it can also lock the Front-Panel Radio Programming or restrict any specific radio feature to be changed (to avoid accidentally erasing the preset radio values). It also provides security by giving the option to set up a password for profile radio’s management. For more information, refer to Features Summary Chart Section at the end of the User Guide.Note: (*) CPS Programming Cable P/N# HKKN4027_ is an accessory sold separately. Please contact your Motorola point of purchase for more information.Time-Out TimerThis timer sets the amount of time that the radio can continuously transmit before the transmission is automatically terminated. The default setting is 60 seconds and can be changed using the CPS. Power SelectPower Select allows you to select between high and low transmission power per frequency in each channel. The power levels for RDX High Power  are 2/4 for UHF and 2/5 for VHFCall TonesCall Tones feature allows you to transmit an audible tone to other radios on the same channel to alert them that you are about to talk or to alert them without speaking.To use this feature, the Call Tones must be programmed to either SB1 or SB2 and 1 of the 3 pre-recorded tones is selected.DRAFT 1
English  45PROGRAMMING FEATURESScramble The Scramble feature makes transmissions sound garbled to anyone listening without the same code. Scramble default value is OFF. To change the scramble code during radio’s normal operation, the Scramble feature must be programmed to either SB1 or SB2.Reverse BurstReverse Burst eliminates unwanted noise (squelch tail) during loss of carrier detection. You can select values of either 180 or 240 to be compatible with other radios. The default value is 180.Notes:• The features described in previous pages are just some of the features CPS has. CPS offers more capabilities. For more information refer to the HELP file in the CPS.• Some of the features available with the CPS software may vary depending on the radio model.Text-to-Speech (Changing Pre-Defined Voice Aliases)Enable User Pre-Defined Voice Prompt (VP)Check the box to enable user-defined voice on the selected channel. The user is given the option to either use the Text-to-Speech synthesizer in order to generate automated voice, or impoart a wave (.wav) file containing the voice data.User Pre-Defined Voice Prompt (VP) TextThis field is used by the Text-to-Speech synthesizer embedded in the CPS to generate user-defined voice for the selected channel.Notes:• The length of the string cannot exceed 18 characters.• The string can only contain ISO-8859-1characters.DRAFT 1
English   46PROGRAMMING FEATURESImport Voice FileThis field allows the user to upload a pre-existing wave (.wav) file from the local hard drive. The first eight cahracters of the wave files are used to populate the channel “Name”.Notes:• The wave file must be sampled at 8 kHz.•This field allows the user to play the outputvoice signal generated from theText-to-Speech synthesizer.DRAFT 1The wave file cannot exceed 65,000 kB in length. Listen to User CustomizedVoice Prompt (VP) Text
English  47PROGRAMMING FEATURESWEATHER FEATURE (not for RDU4103+)The RDX radio weather mode can be programmed to operate and receive weather channels that are broadcasted by the National Weather Radio (NWR). The National Weather Radio system is a nationwide network of radio stations (more than 1000 stations in United States) that broadcast continuous weather information for the public. The NWR broadcasts all types of weather service warnings, watches, forecasts and other hazard information. The NWR can also broadcast non-weather alerts such as national security, natural, environmental, and public safety in conjunctions with the Emergency Alert System (EAS).The RDX radio weather feature can detect weather alerts/warnings that are broadcasted by NWR. The RDX radio can be programmed to detect the analog tone or digital-over-audio protocol.  The analog tone is a 1050 Hz tone (Warning Alarm Tone), which is issued for 10 seconds immediately before the warning message by the NWR transmitter.  When RDX radio detects the Warning Alarm tone, it unmutes audio and  allows the user to hear the weather alert message. As for digital-over-audio protocol, it is a newer technology called Specific Area Message Encoding (SAME) that allows weather radio to receive digital data stream about the type of weather events, timing, duration, and location.  When RDX radio detects these special warnings, the radio can be programmed to automatically generate a loud tone, enable LED indicator, and display “hazard” status on the display.  With the SAME technology, the RDX radio weather mode can be programmed to detect the type of weather warnings or watches for a specified the county or counties. Further information about the National Weather Radio system such as network updates, transmitter coverage maps, and SAME event DRAFT 1
English   48PROGRAMMING FEATUREScodes can be found on the Internet at www.nws.noaa.gov/nwr/.Weather Alert ModeSelect the alert mode the radio will respond to alerts sent from the National Weather Service, which transmitted prior to the broadcast of any message about a life or property threatening event.Choices available are:• OFF (Default): Disable the Weather Alert Feature.• ToneAlert: Detect the Warning Alarm Tone (WAT).• SAME Alert: Detect the Special Area MessageEncoding (SAME).DRAFT 1Weather Channel Frequencies TableNumberFrequency  Value (Mhz)1 162.40002 162.42503 162.45004 162.47505 162.50006 162.52507 162.5500
English  49PROGRAMMING FEATURESThe Weather Alert has two modes of operations:1. In Weather Channel Mode, the radio is in a muted state until it detects the WAT/SAME.When the radio detects the WAT, the radio unmutes and allows the user to hear the weather alert message.2. In two-way mode (on two-way channel), Weather Alert feature becomes a special scanfeature. The radio scans between the current selected two-way channel and the selected weather channel. When the radio detects WAT/SAME signal on the weather channel, the radiounmutes to allow the user to listen the weather message. For Tone Alert, the radio stays inreceiving mode until weather signal is weak or user presses the PTT button or changes the channel using the Channel Selector Knob. ForSAME alert, whether the radio stays in receiving mode or switches back to two-way mode depending on the setting of the EOM Enabled.Warning:  RDX radio does not detect Weather Alert while it is receiving or transmitting on a two-way channel. EOM EnabledThis feature is only available for SAME Alert mode and it is only effective when the radio operates in two-way mode or Weather Channel mode. When checked and in two-way mode, the radio switches back to two-way channel and continues to weather scan after it receives end of message (EOM). For weather channel, the radio mutes and continues to look for new SAME alert after it receives EOM. When unchecked, it stays in receiving mode until weather signal is weak or user presses the PTT button or changes the channel using the Channel Selector Knob.New Alert Tone TimerSelect a pre-defined time for a radio to play the new alert tone. When a radio receives a new SAME alert message, the LED screen lights up  DRAFT 1
English   50PROGRAMMING FEATURESand the radio starts playing the new alert tone at the end of the message. Users have the ability to configure how long the alert tone will be played.Choices available are:• 0 – forever until a button is pressed, or user switches channel, or the new alert message isexpired.• 5 minutes.• 10 minutes.• 30 minutes.Notes: Embedded in the SAME message is the duration of the alert message. The RDX radio continues to display the alert until the duration expiration time.Event Type FilterThe RDX radio is a programmable weather radio that allows users to choose the type of weather warnings and watches that will alarm. The radio can be programmed to allow or block an event by its type.All EventsWhen checked, the radio allows for all SAME events.Alert Test EventWhen SAME alert is enabled, the radio responds to any test events. When checked, the radio alerts the same way as other SAME alert messages. When unchecked, the radio displays only the Message, lights the alert LED without unmuting the radio. The radio does not play the new alert tone at this time.Note: No matter how the user programs the event filter, some critical events cannot be blocked. The National Weather Service broadcast a test alert every week on Wednesday between 11 AM and Noon.  Users should use test alert to ensure that their radios are functioning properly. See also: The Critical Events Table.WarningWhen checked, the radio allows all warning events. Warning events are events that alone DRAFT 1
English  51PROGRAMMING FEATURESpose a significant threat to public safety and/or property.Note: No matter how the user programs the event filter, some critical events cannot be blocked. See also: The Critical Events Table.WatchWhen checked, the radio allows all watch events.  Watches are events that meet the classification of a warning, but either the onset time, probability of occurrence or location is uncertain.Note: No matter how the user programs the event filter, some critical events cannot be blocked. See also: The Critical Events Table.EmergencyWhen checked, the radio allows all emergency events. Emergency event is an event that by itself would not kill or injure or do property damage, but indirectly may cause other things to happen that result in a hazard. Note: No matter how the user programs the event filter, some critical events cannot be blocked. See also: The Critical Events Table.StatementWhen checked, the radio allowS all statement events. Statement is message that contains follow-up information to a warning, watch, or emergency.Note: No matter how the user programs the event filter, some critical events cannot be blocked. See also: The Critical Events Table.Event Code FilterA specific SAME event can be allowed or blocked. There are maximum of 5 Event Codes can be programmed.DRAFT 1
English   52PROGRAMMING FEATURESBlock EventWhen checked, the Event Codes entered below shall be blocked.Note: No matter how the user programs the event filter, some critical events cannot be blocked. See also: The Critical Events Table.Event CodeThe Event Code field accepts wild card (“*”). The following are examples of valid Event Code format.• “***” - all events• FL*” – FLA or FLW•FLAThe “blank” means un-programmed and the radio will bypass it without doing anything.Note: No matter how the user programs the event filter, some critical events cannot be blocked. See also: The Critical Events Table.The Critical Events TableAbbreviation  DescriptionBHW Biological Hazard WarningCDW Civil Danger WarningCEM Civil Emergency MessageCHW Chemical Hazard WarningCWW Contaminated Water WarningDBW Dam Break WarningDEW Contagious Disease WarningEAN Emergency Action NotificationEAT Emergency Action TerminationEQW Earthquake WarningEVI Evacuation ImmediateFCW Food Contamination WarningHMW Hazardous Materials WarningHUW Hurricane WarningIEW Immediate Evacuation WarningDRAFT 1
English  53PROGRAMMING FEATURESGeographic FilterThere are maximum of 6 geographic codes can be programmed. When all fields are unselected, or any of the geographic code is “ALL” for both State and County code (FIPS is “000000”), the radio bypasses the Geographic Filter check.There are two ways to enter the geographic code,• Select State and County Code• Enter the FIPS code directly (must be 6 digits)StateSelects the State, Territory and Offshore (Marine Area) portion (SS) the radio alerts for.CountySelect a county, province, or major metropolitan area (CCC) the radio alerts for.IFW Industrial Fire WarningLAE Local Area EmergencyLEW Law Enforment WarningLSW Land Slide WarningNHW National Hazard WarningNUW Nuclear Power Plant WarningRHW Radiological Hazard WarningSPW Shelter In Place WarningTOR Tornado WarningTOW Tornado WarningTRW Tropical Storm WarningTSA Tsunami WatchTSW Tsunami WarningVOW Volcano WarningWFW Wild Fire WarningDRAFT 1
English   54PROGRAMMING FEATURESFIPSFederal Information Processing Standards (FIPS) contains 6 digits which represent PSSCCC, where P is the region code, SS is the state code and CCC is the county code.Enters/Edits a specific FIPS whenever it is necessary.Further information about FIPS can be found on the Internet at www.nws.noaa.gov/nwr/indexnw.htm or call the National Weather Service Toll-Free Number SAME county code – 1888-NWS-SAME (1-888-697-7263).DRAFT 1
PROGRAMMING FEATURESEnglish  55CLONING RADIOSYou can clone RDX Series™ radio profiles from one Source radio to a Target radio by using any one of these 3 methods:• a Multi Unit Charger (optional accessory),• Two Single Unit Chargers (SUC) and a Radio-to-Radio cloning cable (optional accessory), • the CPS (free software download)Cloning with a Multi Unit Charger (MUC)To clone radios using the MUC, there must be at least two radios:• a Source radio (radio which profiles will be cloned or copied from) and• a Target radio (the radio which profile will be cloned from the source radio.) The Source radio has to be in Pocket 1, 3 or 5 while the Target radio has to be in Pocket 2, 4 or 6, matching in the MUCs pockets by pairs as follows: • 1 and 2 or, • 3 and 4 or, • 5 and 6 (*).When cloning, the MUC does not need to be plugged into a power source, but ALL radios require charged batteries. 1. Turn ON the Target radio and place it into one of the MUC Target Pockets2. Power the Source radio following the sequence below:• Long press the PTT button and SB2 simultaneously while turning the radio ON.
PROGRAMMING FEATURESEnglish   56•  Wait for 3 seconds before releasing the buttons until a distinctive audible tone is heard.3. Place the Source radio in the source pocket that pairs with the target pocket you chose in step 1. Press and release SB1.4. After cloning is completed, the Source radio will sound either a ‘pass’ tone (cloning was successful) or a ‘fail’ tone (cloning process has failed). The ‘pass’ tone sounds like a good key‘chirp’ whereas the ‘fail’ tone sounds similar to a ‘bonk’ tone. If the Source radio is a display model, it will either show ‘Pass’ or ‘Fail’ on the display (a tone will be heard within 5 seconds).5. Once you have completed the cloning process, turn the radios OFF and ON to exit the ‘cloning’ mode.• If cloning fails please refer to “What To Do ifCloning Fails” on page 54.Further details on how to clone radios are explained in the Instructions Sheet provided with the MUC. When ordering the MUC, please refer to P/N RLN6309.Notes:• Paired Target radios and Source radios must be of the same band type in order for the cloning to run successfully. • (*) MUC pockets numbers should be read fromleft to right with the Motorola logo facing front.
PROGRAMMING FEATURESEnglish  57Cloning Radio using the Radio to Radio (R2R) Cloning Cable (Optional Accessory)Operating Instructions1. Before beginning the cloning process, make sure you have:• A fully charged battery on each one of the radios.• Two Single Unit Chargers (SUC).• Turned OFF the radios and,• Both radios are of the same radio model.2. Unplug any cables (power supply or USB cables) from the SUCs.3. Plug one side of the cloning cable mini connector to one SUC. Plug the other end to the second SUC.Note: During the cloning process no power is being applied to the SUC. The batteries will not be charged. A data communication is being established between the two radios.4. Turn ON the Target radio and place it into one of the SUCs.5. On the Source radio, power the radio following the sequence below:• Long press the PTT button and SB2 simultaneously while turning the radio ON.•  Wait for 3 seconds before releasing the buttons until a distinctive audible tone is heard.6. Place the Source radio in its SUC, press and release SB1.
PROGRAMMING FEATURESEnglish   587. After cloning is completed, the Source radio will sound either a ‘pass’ tone (cloning was successful) or a ‘fail’ tone (cloning process has failed). The ‘pass’ tone sounds like a good key‘chirp’ whereas the ‘fail’ tone sounds similar to a ‘bonk’ tone. If the Source radio is a display model, it will either show ‘Pass’ or ‘Fail’ on the display (a tone will be heard within 5 seconds).8. Once you have completed the cloning process, turn the radios OFF and ON to exit ‘clone’ mode. What To Do if Cloning FailsThe radio will emit an audible ‘bonk’ indicating that the cloning process has failed. In the event that cloning fails, try performing each of the following before trying to start the cloning process again:1. Ensure that the batteries on both radios are fully charged.2. Check the cloning cable connection on bothSUCs.3. Ensure that the battery is engaged properly on to the radio.4. Ensure that there is no debris in the charging tray or on the radio contacts.5. Ensure that the Source radio is in cloning mode.6. Ensure that the Target radio is turned ON.7. Ensure that radios are both from the same type (same frequency band, same front panel (display/non display), same region and sametransmission power).Note: This cloning cable is designed to operate only with compatible Motorola RLN6175 (Standard) and RLN6304 (Rapid) Single Unit Chargers.When ordering Optional Cloning Cable please refer to P/N RLN6303. For details about accessories refer to Accessories section.
PROGRAMMING FEATURESEnglish  59Cloning using the CPS (Computer Programming Software)When cloning using this method, you will need to have the CPS software, a Drop-in Tray Charger and the CPS Programming Cable. To order the CPS Programming Cable, please refer to P/N RKN4155.Information on how to clone using the CPS is available either in: • the CPS Help File --> Content and Index --> Cloning Radios, or • in the CPS Programming Cable Accessory Leaflet.
English  60TROUBLESHOOTINGTROUBLESHOOTINGSymptom Try This...No PowerRecharge or replace the Li-Ion battery. Extreme operating temperatures may affect battery life. Refer to “About the Li-Ion Battery” on page 15Hearing other noises or conversation on a channelConfirm Interference Eliminator Code is set. Frequency or Interference Eliminator Code may be in use. Change settings: either change frequencies or codes on all radios. Make sure radio is at the right frequency and code when transmitting. Refer to “Talking and Monitoring” on page 28Message Scrambled Scramble Code might be ON, and/or setting does not match the other radios' settings. Audio quality not good enough Radio settings might not be matching up correctly. Double check frequencies, codes and bandwidths to make sure they are identical in all radiosDRAFT 1
English   61TROUBLESHOOTINGLimited talk rangeTry This...Steel and/or concrete structures, heavy foliage, buildings or vehicles decrease range. Check for clear line of sight to improve transmission. Wearing radio close to body such as in a pocket or on a belt decreases range. Change location of radio. To increase range and coverage, you can reduce obstructions or increase power. UHF radios provides greater coverage in industrial and commercial buildings. Increasing power provides greater signal range and increased penetration through obstructions.Refer to “Talking and Monitoring” on page 28Message not transmitted or receivedMake sure the PTT button is completely pressed when transmitting. Confirm that the radios have the same Channel, Frequency, Interference Eliminator Code and Scramble Code settings. Refer to  “Talking and Monitoring” on page 28 for further information. Recharge, replace and/or reposition batteries. Refer to “About the Li-Ion Battery” on page 15.Obstructions and operating indoors, or in vehicles, may interfere. Change location. Refer to “Talking and Monitoring” on page 28.Verify that the radio is not in Scan. Refer to “Scan” on page 42 and  “Nuisance Channel Delete” on page 43.Symptom DRAFT 1
English  62TROUBLESHOOTINGHeavy static or interferenceRadios are too close; they must be at least five feet apart. Radios are too far apart or obstacles are interfering with transmission. Refer to “Talking and Monitoring” on page 28.Low batteriesRecharge or replace Li-Ion battery.Extreme operating temperatures affect battery life. Refer to “About the Li-Ion Battery” on page 15.Drop-in Charger LED light does not blinkCheck that the radio/battery is properly inserted and check the battery/charger contacts to ensure that they are clean and charging pin is inserted correctly. Refer to “Charging the Battery” on page 21, “Drop-in Tray Charger LED Indicators” on page 24 and “Installing the Lithium-Ion (Li-Ion) Battery” on page 17.Low battery indicator is blinking although new batteries are insertedRefer to “Installing the Lithium-Ion (Li-Ion) Battery” on page 17, and “About the Li-Ion Battery” on page 15.Symptom Try This...DRAFT 1
English   63TROUBLESHOOTINGCannot activate VOXTry This...VOX feature might be set to OFF. Use the CPS to ensure that the VOX Sensitivity level is not set to ‘0’. Accessory not working or not compatible. Refer to “Hands-Free Use/VOX” on page 32. Battery does not charge although it has been placed in the drop-in charger for a whileCheck drop-in tray charger is properly connected and correspond to a compatible power supply. Refer to “Charging with the Drop-in Tray Single Unit Charger (SUC)” on page 21 and “Charging A Stand-Alone Battery” on page 22. Check the charger’s LEDs indicators to see if the battery has a problem. Refer to “Drop-in Tray Charger LED Indicators” on page 24.Note: Whenever a feature in the radio seems to not correspond to the default or preprogrammed values, check to see if the radio has been programmed using the CPS with a customized profile.Symptom DRAFT 1
English  64USE AND CAREIf the radio is submerged in water...USE AND CAREUse a soft damp cloth to clean the exteriorDo not immerse in water Do not use alcohol or cleaning solutionsTurn radio OFF and remove batteriesDry with soft cloth Do not use radio untilcompletely dry
English   65FREQUENCY AND CODE CHARTSFREQUENCY AND CODE CHARTSRDX VHF FREQUENCIES CHARTThe charts in this section provide Frequency and Code information. These charts are useful when using the Motorola RDX Series two-way radios with other business radios.VHF Frequencies – BRUSFrequency # Frequency (MHz) Bandwidth Frequency # Frequency (MHz) Bandwidth1(*) 151.6250 12.5 kHz 15(*) 151.7750 12.5 kHz2(*) 151.9550 12.5 kHz 16 151.8650 12.5 kHz3152.8850 12.5 kHz 17 151.8950 12.5 kHz4152.9150 12.5 kHz 18 151.9250 12.5 kHz5151.7000 12.5 kHz 19 152.9000 12.5 kHz6151.7600 12.5 kHz 20(*) 154.4900 12.5 kHz7152.9450 12.5 kHz 21(*) 154.5150 12.5 kHz8151.8350 12.5 kHz 22 154.5275 12.5 kHz9151.8050 12.5 kHz 23 154.5400 12.5 kHz10(*) 151.5125 12.5 kHz 24 153.0050 12.5 kHz11 151.6550 12.5 kHz 25 154.5475 12.5 kHz12(*) 151.6850 12.5 kHz 26 (**) 158.4000 12.5 kHz13 151.7150 12.5 kHz 27 158.4075 12.5 kHz14 151.7450 12.5 kHz Note: (*) Default FrequenciesDRAFT 1(**) Warning, Receive only Frequency
FREQUENCY AND CODE English   66RDV5100 - VHF DEFAULT FREQUENCIES CHART RDX VHF 10CH Radios Default Frequencies - RDV5100Channel Frequency # Frequency(MHz) Code # Code Bandwidth1 1 151.6250 1 67.0 Hz 12.5 kHz2 1 151.6250 477.0 Hz 12.5 kHz3 1 151.6250 8 88.5 Hz 12.5 kHz4 1 151.6250 29 179.9 Hz 12.5 kHz5 1 151.6250 0 - 12.5 kHz6 2 151.9550 167.0 Hz 12.5 kHz7 2 151.9550 6 82.5 Hz 12.5 kHz8WC 162.4000 10 67.0 Hz25.0 kHz9 2 151.9550 29 179.9 Hz 12.5 kHz10 2151.9550 0 - 12.5 kHzNote: WC = Weather Channel Frequency
English   67FREQUENCY AND CODE CHARTSRDX+ UHF FREQUENCIES CHARTRDX+ UHF FrequenciesFrequency # Frequency (MHz) Bandwidth Frequency # Frequency (MHz) Bandwidth1464.5000 12.5 kHz 15 461.1875 12.5 kHz2464.5500 12.5 kHz 16 461.2125 12.5 kHz3467.7625 12.5 kHz 17 461.2375 12.5 kHz4467.8125 12.5 kHz 18 461.2625 12.5 kHz5467.8500 12.5 kHz 19 461.2875 12.5 kHz6467.8750 12.5 kHz 20 461.3125 12.5 kHz7467.9000 12.5 kHz 21 461.3375 12.5 kHz8467.9250 12.5 kHz 22 461.3625 12.5 kHz9461.0375 12.5 kHz 23 462.7625 12.5 kHz10 461.0625 12.5 kHz 24 462.7875 12.5 kHz11 461.0875 12.5 kHz 25 462.8125 12.5 kHz12 461.1125 12.5 kHz 26 462.8375 12.5 kHz13 461.1375 12.5 kHz 27 462.8625 12.5 kHz14 461.1625 12.5 kHz 28 462.8875 12.5 kHzDRAFT 1
English  68FREQUENCY AND CODE CHARTSFrequency # Frequency (MHz) Bandwidth Frequency # Frequency (MHz) Bandwidth29 462.9125 12.5 kHz 47 466.3625 12.5 kHz30 464.4875 12.5 kHz 48 467.7875 12.5 kHz31 464.5125 12.5 kHz 49 467.8375 12.5 kHz32 464.5375 12.5 kHz 50 467.8625 12.5 kHz33 464.5625 12.5 kHz 51 467.8875 12.5 kHz34 466.0375 12.5 kHz 52 467.9125 12.5 kHz35 466.0625 12.5 kHz 53 469.4875 12.5 kHz36 466.0875 12.5 kHz 54 469.5125 12.5 kHz37 466.1125 12.5 kHz 55 469.5375 12.5 kHz38 466.1375 12.5 kHz 56 469.5625 12.5 kHz39 466.1625 12.5 kHz 57 462.1875 12.5 kHz40 466.1875 12.5 kHz 58 462.4625 12.5 kHz41 466.2125 12.5 kHz 59 462.4875 12.5 kHz42 466.2375 12.5 kHz 60 462.5125 12.5 kHz43 466.2625 12.5 kHz 61 467.1875 12.5 kHz44 466.2875 12.5 kHz 62 467.4625 12.5 kHz45 466.3125 12.5 kHz 63 467.4875 12.5 kHz46 466.3375 12.5 kHz 64 467.5125 12.5 kHzRDX+ UHF Frequencies (Continued)DRAFT 1
English   69FREQUENCY AND CODE CHARTSNote: Frequencies #57 to #89 are 33 new additional frequenciesFrequency # Frequency (MHz) Bandwidth Frequency # Frequency (MHz) Bandwidth65 451.1875 12.5 kHz 78 456.1875 12.5 kHz66 451.2375 12.5 kHz 79 456.2375 12.5 kHz67 451.2875 12.5 kHz 80 456.2875 12.5 kHz68 451.3375 12.5 kHz 81 456.3375 12.5 kHz69 451.4375 12.5 kHz 82 456.4375 12.5 kHz70 451.5375 12.5 kHz 83 456.5375 12.5 kHz71 451.6375 12.5 kHz 84 456.6375 12.5 kHz72 452.3125 12.5 kHz 85 457.3125 12.5 kHz73 452.5375 12.5 kHz 86 457.4125 12.5 kHz74 452.4125 12.5 kHz 87 457.5125 12.5 kHz75 452.5125 12.5 kHz 88 457.7625 12.5 kHz76 452.7625 12.5 kHz 89 457.8625 12.5 kHz77 452.8625 12.5 kHzRDX+ UHF Frequencies (Continued)DRAFT 1
FREQUENCY AND CODE English   70RDU4100+ - UHF DEFAULT FREQUENCIES CHART RDX UHF 10 CH Radios Default Frequencies - RDU4100+Channel Frequency # Frequency(MHz) Code # Code Bandwidth1 1 464.5000 1 67.0 Hz 12.5 kHz2 1 464.5000 477.0 Hz 12.5 kHz3 1 464.5000 8 88.5 Hz 12.5 kHz4 1 464.5000 29 179.9 Hz 12.5 kHz5 1 464.5000 0 - 12.5 kHz6 2 464.5500 167.0 Hz 12.5 kHz7 2 464.5500 6 82.5 Hz 12.5 kHz8WC 162.4000 10 67.0Hz25.0 kHz9 2 464.5500 29 179.9 Hz 12.5 kHz10 2464.5500 0 - 12.5 kHzNote: WC = Weather Channel Frequency
FREQUENCY AND CODE English  71FREQUENCY AND CODE CHARTSRDU4103+ - UHF DEFAULT FREQUENCIES CHART RDX UHF 10 CH Radios Default Frequencies - RDU4103+Channel Freq # Frequency Code # Code Bandwidth1 1 458.6625 1 67.0 Hz 12.5 Khz2 2 469.2625 167.0 Hz 12.5 Khz3 1 458.6625 2 71.9  Hz 12.5 Khz4 2 469.2625 271.9  Hz 12.5 Khz5 1 458.6625 3 74.4 Hz 12.5 Khz6 2 469.2625 374.4 Hz 12.5 Khz7 1 458.6625 4 77.0 Hz 12.5 Khz8 2 469.2625 477.0 Hz 12.5 Khz9 1 458.6625 5 79.7 Hz 12.5 Khz10 2469.2625 579.7 Hz 12.5 Khz
English   72FREQUENCY AND CODE CHARTSCTCSS AND PL/DPL CODESCTCSS CodesCTCSS Hz CTCSS Hz CTCSS Hz1 67.0 14 107.2 27 167.9271.9 15 110.9 28 173.83 74.4 16 114.8 29 179.9477.0 17 118.8 30 186.25 79.7 18 123 31 192.8682.5 19 127.3 32 203.57 85.4 20 131.8 33 210.7888.5 21 136.5 34 218.19 91.5 22 141.3 35 225.710 94.8 23 146.2 36 233.611 97.4 24 151.4 37 241.812 100.0 25 156.7 38 250.313 103.5 26 162.2 122 (*) 69.3Note: (*) New CTCSS code.DRAFT 1
English  73FREQUENCY AND CODE CHARTSPL/DPL CodesDPL Code DPL Code DPL Code39 23 55 116 71 24340 25 56 125 72 24441 26 57 131 73 24542 31 58 132 74 25143 32 59 134 75 26144 43 60 143 76 26345 47 61 152 77 26546 51 62 155 78 27147 54 63 156 79 30648 65 64 162 80 31149 71 65 165 81 31550 72 66 172 82 33151 73 67 174 83 34352 74 68 205 84 34653 114 69 223 85 35154 115 70 226 86 364DRAFT 1
English   74FREQUENCY AND CODE CHARTS87 365 104 565 121 75488 371 105 606 123 64589 411 106 612 124 Customized PL90 412 107 624 125 Customized PL91 413 108 627 126 Customized PL92 423 109 631 127 Customized PL93 431 110 632 128 Customized PL94 432 111 654 129 Customized PL95 445 112 662 130 Inverted DPL 3996 464 113 664 131 Inverted DPL 4097 465 114 703 132 Inverted DPL 4198 466 115 712 133 Inverted DPL 4299 503 116 723 134 Inverted DPL 43100 506 117 731 135 Inverted DPL 44101 516 118 732 136 Inverted DPL 45102 532 119 734 137 Inverted DPL 46103 546 120 743 138 Inverted DPL 47PL/DPL Codes (Continued) DPL Code DPL Code DPL CodeDRAFT 1
English  75FREQUENCY AND CODE CHARTS139 Inverted DPL 48 156 Inverted DPL 65 173 Inverted DPL 82140 Inverted DPL 49 157 Inverted DPL 66 174 Inverted DPL 83141 Inverted DPL 50 158 Inverted DPL 67 175 Inverted DPL 84142 Inverted DPL 51 159 Inverted DPL 68 176 Inverted DPL 85143 Inverted DPL 52 160 Inverted DPL 69 177 Inverted DPL 86144 Inverted DPL 53 161 Inverted DPL 70 178 Inverted DPL 87145 Inverted DPL 54 162 Inverted DPL 71 179 Inverted DPL 88146 Inverted DPL 55 163 Inverted DPL 72 180 Inverted DPL 89147 Inverted DPL 56 164 Inverted DPL 73 181 Inverted DPL 90148 Inverted DPL 57 165 Inverted DPL 74 182 Inverted DPL 91149 Inverted DPL 58 166 Inverted DPL 75 183 Inverted DPL 92150 Inverted DPL 59 167 Inverted DPL 76 184 Inverted DPL 93151 Inverted DPL 60 168 Inverted DPL 77 185 Inverted DPL 94152 Inverted DPL 61 169 Inverted DPL 78 186 Inverted DPL 95153 Inverted DPL 62 170 Inverted DPL 79 187 Inverted DPL 96154 Inverted DPL 63 171 Inverted DPL 80 188 Inverted DPL  97155 Inverted DPL 64 172 Inverted DPL 81 189 Inverted DPL  98PL/DPL Codes (Continued) DPL Code DPL Code DPL CodeDRAFT 1
English   76FREQUENCY AND CODE CHARTS190 Inverted DPL 99 200 Inverted DPL 109 210 Inverted DPL 119191 Inverted DPL 100 201 Inverted DPL 110 211 Inverted DPL 120192 Inverted DPL 101 202 Inverted DPL 111 212 Inverted DPL 121193 Inverted DPL 102 203 Inverted DPL 112 213 Inverted DPL 123194 Inverted DPL 103 204 Inverted DPL 113 214 Customized DPL195 Inverted DPL 104 205 Inverted DPL 114 215 Customized DPL196 Inverted DPL 105 206 Inverted DPL 115 216 Customized DPL197 Inverted DPL 106 207 Inverted DPL 116 217 Customized DPL198 Inverted DPL 107 208 Inverted DPL 117 218 Customized DPL199 Inverted DPL 108 209 Inverted DPL 118 219 Customized DPLPL/DPL Codes (Continued) DPL Code DPL Code DPL CodeDRAFT 1
English  77FREQUENCY AND CODE CHARTSNotesDRAFT 1
English   78MOTOROLA LIMITED WARRANTY FOR THE UNITED STATES AND CANADAMOTOROLA LIMITED WARRANTY FOR THE UNITED STATES AND CANADAWhat Does this Warranty Cover?Subject to the exclusions contained below, Motorola, Inc. warrants its telephones, pagers, and consumer and business two-way radios (excluding commercial, government or industrial radios) that operate via Family Radio Service or General Mobile Radio Service, Motorola-branded or certified accessories sold for use with these Products (“Accessories”) and Motorola software contained on CD-ROMs or other tangible media and sold for use with these Products (“Software”) to be free from defects in materials and workmanship under normal consumer usage for the period(s) outlined below. This limited warranty is a consumer's exclusive remedy, and applies as follows to new Motorola Products, Accessories and Software purchased by consumers in the United States, which are accompanied by this written warranty.Products and Accessories Products Covered Length of CoverageProducts and Accessories as defined above, unless otherwise provided for below.One (1) year from the date of purchase by the first consumer purchaser of the product unless otherwise provided for below.Decorative Accessories and Cases.Decorative covers, bezels, PhoneWrap™ covers and cases.Limited lifetime warranty for the lifetime of ownership by the first consumer purchaser of the product.Business Two-way Radio AccessoriesOne (1) year from the date of purchase by the first consumer purchaser of the product.Products and Accessories that are Repaired or Replaced.The balance of the original warranty or for ninety (90) days from the date returned to the consumer, whichever is longer.DRAFT 1
English  79MOTOROLA LIMITED WARRANTY FOR THE UNITED STATES AND CANADAExclusionsNormal Wear and Tear. Periodic maintenance, repair and replacement of parts due to normal wear and tear are excluded from coverage.Batteries. Only batteries whose fully charged capacity falls below 80% of their rated capacity and batteries that leak are covered by this limited warranty.Abuse & Misuse. Defects or damage that result from: (a) improper operation, storage, misuse or abuse, accident or neglect, such as physical damage (cracks, scratches, etc.) to the surface of the product resulting from misuse; (b) contact with liquid, water, rain, extreme humidity or heavy perspiration, sand, dirt or the like, extreme heat, or food; (c) use of the Products or Accessories for commercial purposes or subjecting the Product or Accessory to abnormal usage or conditions; or (d) other acts which are not the fault of Motorola, are excluded from coverage. Use of Non-Motorola Products and Accessories. Defects or damage that result from the use of Non-Motorola branded or certified Products, Accessories, Software or other peripheral equipment are excluded from coverage.Unauthorized Service or Modification. Defects or damages resulting from service, testing, adjustment, installation, maintenance, alteration, or modification in any way by someone other than Motorola, or its authorized service centers, are excluded from coverage.Altered Products. Products or Accessories with (a) serial numbers or date tags that have been removed, altered or obliterated; (b) broken seals or that show evidence of tampering; (c) mismatched board serial numbers; or (d) nonconforming or non-Motorola housings, or parts, are excluded form coverage.DRAFT 1
English   80MOTOROLA LIMITED WARRANTY FOR THE UNITED STATES AND CANADACommunication Services. Defects, damages, or the failure of Products, Accessories or Software due to any communication service or signal you may subscribe to or use with the Products Accessories or Software is excluded from coverage.Software ExclusionsSoftware Embodied in Physical Media. No warranty is made that the software will meet your requirements or will work in combination with any hardware or software applications provided by third parties, that the operation of the software products will be uninterrupted or error free, or that all defects in the software products will be corrected.Software NOT Embodied in Physical Media. Software that is not embodied in physical media (e.g. software that is downloaded from the internet), is provided “as is” and without warranty.WHO IS COVERED?This warranty extends only to the first consumer purchaser, and is not transferable.HOW TO OBTAIN WARRANTY SERVICE OR OTHER INFORMATION?Contact your Motorola point of purchase.SOFTWARE COPYRIGHT NOTICEThe Motorola products described in this manual may include copyrighted Motorola and third party software stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola and third party software providers certain exclusive rights for copyrighted software, such as the exclusive rights to distribute or reproduce the copyrighted software. Accordingly, any copyrighted software contained in the Motorola products may not be modified, reverse-engineered, distributed, or reproduced in any manner to the extent allowed by law.Products Covered Length of CoverageSoftware. Applies only to physical defects in the media that embodies the copy of the software (e.g. CD-ROM, or floppy disk).Ninety (90) days from the date of purchase.DRAFT 1
English  81MOTOROLA LIMITED WARRANTY FOR THE UNITED STATES AND CANADAFurthermore, the purchase of the Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents, or patent applications of Motorola or any third party software provider, except for the normal, non-exclusive, royalty-free license to use that arises by operation of law in the sale of a product.PATENT NOTICEThis product is covered by one or more of the following United States patents.5896277 5894292 5864752 5699006 5742484 D408396 D399821 D387758 D389158 5894592 5893027 5789098 5734975 5861850 D395882 D383745 D389827 D389139 5929825 5926514 5953640 6071640 D413022 D416252 D416893 D433001EXPORT LAW ASSURANCESThis product is controlled under the export regulations of the United States of America. The Governments of the United States of America may restrict the exportation or re-exportation of this product to certain destinations. For further information contact the U.S. Department of Commerce.DRAFT 1
ACCESSORIESEnglish   82ACCESSORIESANTENNAS AUDIO ACCESSORIESPart No. DescriptionRAN4041 VHF Helical Antenna 146-174 MHzRAN4031 UHF Whip Antenna 438 - 470 MHzPart HKLN4477Description Surveillance Earpiece BR5386656517RLN6423Description  Earbud w/Clip PTT Mic BR Earpiece w/Inline Mic Swivel Earpiece BRPart No.BATTERYPart No. DescriptionRLN6308   High Capacity Li-Ion Battery
ACCESSORIESEnglish  83CARRY ACCESSORIESPOWER SUPPLIES AC PIN ADAPTORSSOFTWARE APPLICATIONSCABLESCHARGERSDescriptionPart No.  RLN6307  Spring Action Belt ClipPart No.  DescriptionRLN6349 North America AC Pin Adaptor Part No. DescriptionRVN5147 Computer Programming Software (CPS) Part No. DescriptionRLN6303 Radio to Radio Cloning Cable RKN4155 CPS Programming Cable Part No. DescriptionRLN6304 Rapid ACCY Charging Kit - Americas (*)RLN6309 Multi Unit Charger (MUC) Kit - North America RLN6175 Standard Drop-in Tray Charger
ACCESSORIESEnglish   84POWER SUPPLIESPart No. DescriptionRPN4054 Standard US Fixed Power Supply RPN4058 Standard Exchg AC pin Pwr SupplyRLN6170 Rapid Exchg AC pin Pwr Supply Attention: Certain accessories may be or may not be available at the time of purchase. For latest information on accessories, contact your Motorola point of purchase or visit: www.motorolasolutions.com/RDX (*) Americas Rapid Charging Kit includes Power Supply, Drop-in Tray Charger, and AC Pin adaptors.
English   85ACCESSORIESNotesDRAFT 1
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners.© 2013, 2014 Motorola Solutions, Inc. All rights reserved.*68012009072*6871663M01-CmMotorola Solutions, Inc.1303 E. Algonquin Rd. Schaumburg, IL 60196-1078, U.S.A.http://www.motorolasolutions.comDRAFT 1

Navigation menu