Motorola Solutions 89FT5863 PORTABLE MULTIBAND 2-WAY RADIO User Manual APX 6000 M1 5 Portable Radio User Guide
Motorola Solutions, Inc. PORTABLE MULTIBAND 2-WAY RADIO APX 6000 M1 5 Portable Radio User Guide
Contents
- 1. Users Guide
- 2. RF Safety Guide
- 3. User Manual
Users Guide
APX 6000 User Guide Model 1.5 68012001081-A m Receiving and Transmitting ASTRO® APX™ 6000 Series Digital Portable Radios Quick Reference Card 1 Select zone/channel. 2 Listen for a transmission. Product Safety and RF Exposure Compliance Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF C a u t i o n Exposure booklet enclosed with your radio. ATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed with your radio (Motorola Publication part number 6881095C98) to ensure compliance with RF energy exposure limits. PICTURE TO BE REPLACED WITH APX 6000 MODEL 1.5 OR Press and hold Volume Set button. OR Press Monitor button and listen for activity. 3 Adjust volume, if necessary. 4 Press the PTT button to transmit; release to receive. Sending an Emergency Alarm Radio Controls 1 Press the Emergency button. 2 The display shows EMERGNCY and the current zone/channel. A short, mediumpitched tone sounds, and the LED rapidly blinks red. PICTURE TO BE REPLACED WITH APX 6000 MODEL 1.5 3 When acknowledgment is received, you hear Radio On/Off • On – On/Off/Volume knob clockwise. • Off – On/Off/Volume knob counterclockwise. four beeps; alarm ends; and radio exits emergency. To exit emergency at any time, press and hold the Emergency button. Zones and Channels • Zone – Zone switch to desired zone. • Channel – Channel switch to desired channel. © 2010 by Motorola, Inc. All Rights Reserved. 06/10 1301 E. Algonquin Rd., Schaumburg, IL 60196-1078, U.S.A. *PMLN5715A* PMLN5715A English Sending an Emergency Call 1 Press the Emergency button. 2 Press and hold the PTT button. Speak clearly into the microphone. 3 Release the PTT button to end call. 4 Press and hold Emergency button to exit emergency. To exit emergency at any time, press and hold the Emergency button. Sending a Silent Emergency Call 1 Press the Emergency button. 2 The display does not change; the LED does not light up, and there is no tone. 3 Silent emergency continues until you: Press and hold the Emergency button to exit emergency state. OR Press and release the PTT button to exit silent emergency mode and enter regular emergency (alarm, call, or alarm with call) mode. To exit emergency at any time, press and hold the Emergency button. English Display Status Icons Blinks when the battery is low. Direct radio to radio communication or connected through a repeater. On = Direct Off = Repeater The more stripes, the stronger the signal strength for the current site (trunking only). M This channel is being monitored. is set at Low power. H L LH == Radio Radio is set at High power. i Scanning a scan list. OR Blinking dot = Detects activity on the Priority-One Channel during scan. Steady dot = Detects activity on the Priority-Two Channel during scan. The vote scan feature is enabled. On = Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. On steady = View mode Blinking = Program mode Aor Bor Zone Bank 1 A = Radio is in Zone 1. B = Radio is in Zone 2. C = Radio is in Zone 3. Dor Eor Zone Bank 2 D = Radio is in Zone 4. E = Radio is in Zone 5. F = Radio is in Zone 6. Declaration of Conformity DECLARATION OF CONFORMITY Per FCC CFR 47 Part 2 Section 2.1077(a) Responsible Party Name: Motorola, Inc. Address: 1301 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A. Phone Number: 1-800-927-2744 Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. Hereby declares that the product: Model Name: APX 6000 conforms to the following regulations: FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a) Class B Digital Device As a personal computer peripheral, this device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. English Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. Declaration of Conformity • Increase the separation between the equipment and receiver. ii English • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Contents Encrypted Integrated Data (EID) . . . . . . . . . . . . . . . 2 SecureNet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 What Your Dealer/System Administrator Can Tell You . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Declaration of Conformity . . . . . . . . . . . . . . . . . .i Preparing Your Radio for Use . . . . . . . . . . . . . .3 Important Safety Information . . . . . . . . . . . . . vii Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . 4 Battery Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 P roduct Safety and RF Exposure Compliance . . . vii Attaching the Battery . . . . . . . . . . . . . . . . . . . . . . . . . 4 Software Version . . . . . . . . . . . . . . . . . . . . . . . vii Computer Software Copyrights . . . . . . . . . . .viii Contents This User Guide contains all the information you need to use the AP X™ 6000 Series Digital P ortable Radios. Attaching the Antenna . . . . . . . . . . . . . . . . . . . . . . . . 5 Attaching the Accessory Connector Cover . . . . . . . . 6 Attaching the Belt Clip . . . . . . . . . . . . . . . . . . . . . . . . 6 Turning On the Radio . . . . . . . . . . . . . . . . . . . . . . . . 7 Documentation Copyrights . . . . . . . . . . . . . . .viii Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . 8 Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii Identifying Radio Controls . . . . . . . . . . . . . . . . .8 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . 1 How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . . 1 Notations Used in This Manual . . . . . . . . . . . . . . . . . 1 Additional P erformance Enhancement . . . . . . . . . . 2 Dynamic System Resilience (DSR) . . . . . . . . . . . . . .2 CrossTalk Prevention . . . . . . . . . . . . . . . . . . . . . . . .2 Radio P arts and Controls . . . . . . . . . . . . . . . . . . . . 9 P rogrammable Features . . . . . . . . . . . . . . . . . . . . 10 Assignable Radio Functions . . . . . . . . . . . . . . . . . 10 Assignable Settings or Utility Functions . . . . . . . . . 11 Accessing the P reprogrammed Functions . . . . . . . 11 P ush-To-Talk (P TT) Button . . . . . . . . . . . . . . . . . 11 iii English Identifying Status Indicators . . . . . . . . . . . . . .12 Advanced Features . . . . . . . . . . . . . . . . . . . . . 24 Status Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Alert Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Advanced Call Features . . . . . . . . . . . . . . . . . . . . . 24 Receiving and Responding to a Selective Call (ASTRO Conventional Only) . . . . . . . . . . . . . . . . . . . . . . . . .24 Using the Dynamic Regrouping Feature (Trunking Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 General Radio Operation . . . . . . . . . . . . . . . . .18 Requesting a Reprogram (Trunking Only) . . . . . . .25 Classifying Regrouped Radios . . . . . . . . . . . . . . . .26 LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Intelligent Lighting Indicators . . . . . . . . . . . . . . . . . 14 Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Selecting a Radio Channel . . . . . . . . . . . . . . . . . . . 19 Receiving and Responding to a Radio Call . . . . . . 19 Receiving and Responding to a Talkgroup Call . . . 20 Receiving and Responding to a Private Call (Trunking Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Receiving and Responding to a Telephone Call (Trunking Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Contents Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . 22 Making a Talkgroup Call . . . . . . . . . . . . . . . . . . . . . 22 Repeater or Direct Operation . . . . . . . . . . . . . . . . . 22 Monitoring Features . . . . . . . . . . . . . . . . . . . . . . . . 23 Monitoring a Channel . . . . . . . . . . . . . . . . . . . . . . . 23 Conventional Mode Operation . . . . . . . . . . . . . . . . 23 iv English Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Viewing a Scan List . . . . . . . . . . . . . . . . . . . . . . . . .26 Viewing and Changing the Priority Status . . . . . . . .26 Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Turning Scan On or Off . . . . . . . . . . . . . . . . . . . . . .27 Making a Dynamic Priority Change (Conventional Scan Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Deleting a Nuisance Channel . . . . . . . . . . . . . . . . .28 Restoring a Nuisance Channel . . . . . . . . . . . . . . . .28 Call Alert P aging . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Receiving a Call Alert Page . . . . . . . . . . . . . . . . . .29 Emergency Operation . . . . . . . . . . . . . . . . . . . . . . 29 Sending an Emergency Alarm . . . . . . . . . . . . . . . .30 Sending an Emergency Call (Trunking Only) . . . . .30 Sending an Emergency Alarm with Emergency Call 31 Sending a Silent Emergency Alarm . . . . . . . . . . . .32 Using the Emergency Keep-Alive Feature . . . . . . .32 Loading an Encryption Key . . . . . . . . . . . . . . . . . . 34 Using the Multikey Feature . . . . . . . . . . . . . . . . . . 34 Erasing the Selected Encryption Keys . . . . . . . . . . 35 Requesting an Over-the-Air Rekey (ASTRO Conventional Only) . . . . . . . . . . . . . . . . . . . . . . . . 35 MDC Over-the-Air Rekeying (OTAR) Page . . . . . . 36 Hear Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Trunking System Controls . . . . . . . . . . . . . . . . . . . . 37 Using the Failsoft System . . . . . . . . . . . . . . . . . . . .37 Going Out of Range . . . . . . . . . . . . . . . . . . . . . . . .37 Using the Site Trunking Feature . . . . . . . . . . . . . . .38 Locking and Unlocking a Site . . . . . . . . . . . . . . . . .38 Viewing and Changing a Site . . . . . . . . . . . . . . . . .38 Viewing the Current Site . . . . . . . . . . . . . . . . . . . . 38 Changing the Current Site . . . . . . . . . . . . . . . . . . . 38 Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Turning on the Bluetooth . . . . . . . . . . . . . . . . . . . . .39 Turning off the Bluetooth . . . . . . . . . . . . . . . . . . . . .39 Pairing Bluetooth device with the Radio . . . . . . . . .39 Indicating Bluetooth Connection is Lost . . . . . . . . .40 Turning on the Bluetooth Audio . . . . . . . . . . . . . . . .40 Turning off the Bluetooth Audio . . . . . . . . . . . . . . . .40 Adjusting the Volume of the radio from Bluetooth Audio Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Using the Flip Display . . . . . . . . . . . . . . . . . . . . . . 41 Selecting a Zone Bank . . . . . . . . . . . . . . . . . . . . . . 41 Selecting the Power Level . . . . . . . . . . . . . . . . . . . 41 Controlling the Display Backlight . . . . . . . . . . . . . . 42 Turning Voice Mute On or Off . . . . . . . . . . . . . . . . 42 Using the Time-Out Timer . . . . . . . . . . . . . . . . . . . 42 Using the Conventional Squelch Operation Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Contents Secure Operations . . . . . . . . . . . . . . . . . . . . . . . . . 33 Selecting Secure Transmissions . . . . . . . . . . . . . . .33 Selecting Clear Transmissions . . . . . . . . . . . . . . . .33 Managing Encryption . . . . . . . . . . . . . . . . . . . . . . .34 Analog Options . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Digital Options . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Using the PL Defeat Feature . . . . . . . . . . . . . . . . . Using the Digital PTT ID Feature . . . . . . . . . . . . . . Using the Smart PTT Feature (Conventional Only) Voice Announcement . . . . . . . . . . . . . . . . . . . . . . . 44 45 45 46 Helpful Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 Caring for Your Radio . . . . . . . . . . . . . . . . . . . . . . . 48 Cleaning Your Radio . . . . . . . . . . . . . . . . . . . . . . . 49 Handling Your Radio . . . . . . . . . . . . . . . . . . . . . . . 49 Servicing Your Radio . . . . . . . . . . . . . . . . . . . . . . . 50 Taking Care of the Battery . . . . . . . . . . . . . . . . . . . 50 Checking the Battery Charge Status . . . . . . . . . . . 50 LED and Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . 50 English Fuel Gauge Icon . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Battery Recycling and Disposal . . . . . . . . . . . . . . . 51 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Appendix: Maritime Radio Use in the VHF Frequency Range . . . . . . . . . . . . . . . . . . . . . . .53 Special Channel Assignments . . . . . . . . . . . . . . . . 53 Emergency Channel . . . . . . . . . . . . . . . . . . . . . . . . 53 Non-Commercial Call Channel . . . . . . . . . . . . . . . . 53 Operating Frequency Requirements . . . . . . . . . . . 54 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 Commercial Warranty . . . . . . . . . . . . . . . . . . . .60 Contents Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 vi English Software Version Product Safety and RF Exposure Compliance All the features described in the following sections are supported by the radio's software version R05.00.00 or later. Caution Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio. ATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the P roduct Safety and RF Exposure booklet enclosed with your radio (Motorola P ublication part number 6881095C98) to ensure compliance with RF energy exposure limits. Check with your dealer or system administrator for more details of all the features supported. Important Safety Information Important Safety Information For a list of Motorola-approved antennas, batteries, and other accessories, visit the following website: http://www.motorola.com/governmentandenterprise vii English Computer Software Copyrights Computer Software Copyrights Documentation Copyrights The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs, including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied, reproduced, modified, reverse-engineered, or distributed in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive license to use that arises by operation of law in the sale of a product. No duplication or distribution of this document or any portion thereof shall take place without the express written permission of Motorola. No part of this manual may be reproduced, distributed, or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of Motorola. viii English Disclaimer The information in this document is carefully examined, and is believed to be entirely reliable. However, no responsibility is assumed for inaccuracies. Furthermore, Motorola reserves the right to make changes to any products herein to improve readability, function, or design. Motorola does not assume any liability arising out of the applications or use of any product or circuit described herein; nor does it cover any license under its patent rights, nor the rights of others. Getting Started How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . . . . page 1 Notations Used in This Manual . . . . . . . . . . . . . . . . . . . page 1 Additional Performance Enhancement . . . . . . . . . . . . . page 2 What Your Dealer/System Administrator Can Tell You. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3 How to Use This Guide This User Guide covers the basic operation of the APX™ 6000 Portables. However, your dealer or system administrator may have customized your radio for your specific needs. Check with your dealer or system administrator for more information. Throughout the text in this publication, you will notice the use of WARNING, Caution, and Note. These notations are used to emphasize that safety hazards exist, and the care that must be taken or observed. An operational procedure, practice, or condition, etc., which may result in injury or death if not carefully observed. An operational procedure, practice, or condition, etc., which may result in damage to the equipment if not carefully observed. WARNING Caution Note: Getting Started Take a moment to review the following: Notations Used in This Manual An operational procedure, practice, or condition, etc., which is essential to emphasize. English Additional Performance Enhancement The following are some of the latest creations designed to enhance the security, quality and efficiency of APX radios. Dynamic System Resilience (DSR) DSR ensures the radio system is seamlessly switched to a backup master site dynamically in case of system failure. DSR also provides additional indication e.g. failure detection, fault recovery, and redundancy within the system to address to the user in need. Mechanisms related to the Integrated Voice and Data (IV & D) or data centric are all supported by DSR. Getting Started CrossTalk Prevention This feature prevents crosstalk scenario from happening, especially when a wideband antenna is used. This feature allows the adjustment of the Trident Transmitting SSI clock rate in the radio to be varied from the Receiving Frequency. This subsequently reduced the possibilities of radio frequency interfering spurs and prevents the issues of crosstalk. English Encrypted Integrated Data (EID) EID provides security encryption and authentication of IV & D data bearer service communication between the radio and the Customer Enterprise Network. SecureNet SecureNet allows user to perform secured communications on an Analog or Motorola Data Communication (MDC) channel. The MDC OTAR feature will allow users to perform OTAR activities on an MDC channel. What Your Dealer/System Administrator Can Tell You You can also consult your dealer or system administrator about the following: • Is your radio preprogrammed with any preset conventional channels? • Which buttons have been preprogrammed to access other features? • What optional accessories may suit your needs? Assemble your radio by following these steps: Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4 Battery Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4 Attaching the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4 Attaching the Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . page 5 Attaching the Belt Clip . . . . . . . . . . . . . . . . . . . . . . . . . . page 6 Attaching the Accessory Connector Cover . . . . . . . . . . page 6 Turning On the Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7 Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . page 8 Preparing Your Radio for Use Check with your dealer or system administrator, if the radio is to be operated in extremely cold temperatures (less than -20 °C), for the correct radio settings to ensure proper top display operation. Preparing Your Radio for Use English Charging the Battery To avoid a possible explosion: Preparing Your Radio for Use WARNING Attaching the Battery With the radio turned off, slide the battery into the radio’s frame until side latches click into place. • DO NOT replace the battery in any area labeled “hazardous atmosphere”. • DO NOT discard batteries in a fire. The Motorola-approved battery shipped with your radio is uncharged. Prior to using a new battery, charge it for a minimum of 16 hours to ensure optimum capacity and performance. For a list of Motorola-authorized batteries available for use with your radio, see Accessories on page 52. Note: When charging a battery attached to a radio, turn the radio off to ensure a full charge. Battery Charger To charge the battery, place the battery, with or without the radio, in a Motorola-approved charger. The charger’s LED indicates the charging progress; see your charger’s user guide. For a list of chargers, see Accessories on page 52. English PICTURE TO BE REPLACED WITH APX 6000 MODEL 1.5 Note: If your radio is preprogrammed with volatile-key retention, the encryption keys are retained for approximately 30 seconds after battery removal. Check with your dealer or system administrator for more information. Attaching the Antenna With the radio turned off, set the antenna in its receptacle and turn clockwise to attach it to the radio. PICTURE TO BE REPLACED WITH APX 6000 MODEL 1.5 Preparing Your Radio for Use PICTURE TO BE REPLACED WITH APX 6000 MODEL 1.5 To remove the battery, turn the radio off. Squeeze the release latches on the bottom of the battery until the battery releases from the radio. Remove the battery from the radio. To remove the antenna, turn the antenna counterclockwise. Make sure you turn off the radio first. English Attaching the Accessory Connector Cover The accessory connector is located on the antenna side of the radio. It is used to connect accessories to the radio. Preparing Your Radio for Use Note: To prevent damage to the connector, shield it with the connector cover when not in use. Insert the hooked end of the cover into the slot above the connector. Press downward on the cover’s top to seat it in the slot. Once in place, rotate the thumbscrew clockwise by hand until tight. Align the grooves of the belt clip with those of the radio and press upward until you hear a click. PICTURE TO BE REPLACED WITH APX 6000 MODEL 1.5 PICTURE TO BE REPLACED WITH APX 6000 MODEL 1.5 To remove the accessory connector cover, rotate the thumbscrew counterclockwise until it disengages from the radio. If the thumbscrew is too tight, use an Allen wrench to loosen it first. Rotate and lift the connector cover to disengage it from the radio. English Attaching the Belt Clip PICTURE TO BE REPLACED WITH APX 6000 MODEL 1.5 To remove the clip, use a flat-bladed object to press the belt clip tab away from the radio. Then, slide the clip downward and away from the radio. Turning On the Radio PICTURE TO BE REPLACED WITH APX 6000 MODEL 1.5 PICTURE TO BE REPLACED WITH APX 6000 MODEL 1.5 To turn off the radio, rotate the On/Off/Volume Control Knob counterclockwise until you hear a click. If the power-up test is successful, you see SELFTEST on the radio’s display momentarily, followed by the Home screen. Note: Preparing Your Radio for Use Rotate the On/Off/Volume Control Knob clockwise until you hear a click. If the power-up test is unsuccessful, you see ERROR XX/YY (XX/YY is an alphanumeric code). Turn off the radio, check the battery, and turn the radio back on. If the radio fails the power-up test again, record the ERROR XX/YY code and contact your dealer. English Adjusting the Volume To increase the volume, turn the On/Off/Volume Control Knob clockwise. Identifying Radio Controls PICTURE TO BE REPLACED WITH APX 6000 MODEL 1.5 To decrease the volume, turn this knob counterclockwise. Note: English Ensure that the main speaker is pointed towards you for increased loudness and intelligibility, especially in areas with loud background noises. Identifying Radio Controls Take a moment to review the following: Radio Parts and Controls. . . . . . . . . . . . . . . . . . . . . . . . page 9 Programmable Features . . . . . . . . . . . . . . . . . . . . . . . page 10 Assignable Radio Functions. . . . . . . . . . . . . . . . . . . page 10 Assignable Settings or Utility Functions . . . . . . . . . . page 11 Accessing the Preprogrammed Functions. . . . . . . . . . page 11 Push-To-Talk (PTT) Button . . . . . . . . . . . . . . . . . . . . . page 11 Radio Parts and Controls Identifying Radio Controls PICTURE TO BE REPLACED WITH APX 6000 MODEL 1.5 English Programmable Features Any reference in this manual to controls that are “preprogrammed” means that a qualified radio technician must use the radio’s programming software to assign a feature to a control. Identifying Radio Controls Your dealer can program the programmable buttons as shortcuts to radio functions or preset channels/groups depending on the duration of a button press: • Press – Pressing and releasing rapidly. • Long press – Pressing and holding for the preprogrammed duration (between 0.25 seconds and 3.75 seconds). • Hold down – Keeping the button pressed. Assignable Radio Functions Call Response – Allows you to answer a private call. Channel – Selects a channel. Dynamic Priority (Conventional Only) – Allows any channel in a scan list (except for the Priority-One channel) to temporarily replace the Priority-Two channel. Emergency – Depending on the programming, initiates or cancels an emergency alarm or call. 10 English Internet Protocol – Displays the Internet Protocol(IP) address, device name and status of the radio. Message – Enters the current message list. Monitor (Conventional Only) – Monitors a selected channel for all radio traffic until function is disabled. Multiple Private Line (Conventional Only) – Selects the Mulitple Private Line lists. Nuisance Delete – Temporarily removes an unwanted channel, except for priority channels or the designated transmit channel, from the scan list. One Touch 1 – 4 – Launches a specific feature with one single button-press. You can setup as much as four separately programmed buttons for four different features. Private Line Defeat – Overrides any coded squelch (DPL or PL) that is preprogrammed to a channel. Rekey Request – Notifies the dispatcher that you require a new encryption key. Repeater Access Button (RAB) (Conventional Only) – Allows to manually send a repeater access codeword. Reprogram Request (Trunking Only) – Notifies the dispatcher that you want a new dynamic regrouping assignment. Request-To-Talk (Conventional Only) – Notifies the dispatcher that you want to send a voice call. Scan – Toggles scan on or off. Scan List Programming – Selects the scan list for editing. You can access various radio functions through a short or long press of the relevant programmable buttons. Site Display – Displays the current site ID and RSSI value. Site Lock/Unlock – Locks onto a specific site. Site Search – Performs site search for AMSS (Automatic Multiple Site Select) or SmartZone operation. Talkaround/Direct – Toggles between using a repeater and communicating directly with another radio. Zone Select – Allows selection from a list of zones. Zone Bank – Allows selection from a larger list of zones. Assignable Settings or Utility Functions Flip – Flips the content of the top display. Light – Toggles display backlight on or off. TX Power Level – Toggles transmit power level between high and low. Voice Mute – Toggles voice mute on or off. Volume Set – Sets the volume set tone. Push-To-Talk (PTT) Button The PTT button on the side of the radio serves two basic purposes: • While a call is in progress, the PTT button allows the radio to transmit to other radios in the call. Press and hold down PTT button to talk. Release the PTT button to listen. PICTURE TO BE REPLACED WITH APX 6000 MODEL 1.5 Identifying Radio Controls Secure/Clear – Toggles secure operation on or off. Accessing the Preprogrammed Functions The microphone is activated when the PTT button is pressed. • While a call is not in progress, the PTT button is used to make a new call. See Making a Radio Call on page 22 for more information. 11 English Identifying Status Indicators Your radio indicates its operational status through the following: Identifying Status Indicators Status Icons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Intelligent Lighting Indicators. . . . . . . . . . . . . . . . . . . . Alert Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 12 page 13 page 14 page 15 Status Icons The 112 x 32 pixel top monochrome display screen of your radio shows the radio status and operating conditions. Battery The icon shown indicates the charge remaining in the battery. Blinks when the battery is low. Received Signal Strength Indicator (RSSI) The number of bars displayed represents the received signal strength for the current site, for trunking only. The more stripes in the icon, the stronger the signal. Direct • On = Radio is currently configured for direct radio to radio communication (during conventional operation only). • Off = Radio is connected with other radios through a repeater. H L or Monitor (Carrier Squelch) Selected channel is being monitored (during conventional operation only). Power Level • L = Radio is set at Low power. • H = Radio is set at High power. Scan Radio is scanning a scan list. Priority Channel Scan • Blinking dot = Radio detects activity on channel designated as PriorityOne. • Steady dot = Radio detects activity on channel 12 English designated as Priority-Two. Top Display View/Program Mode Radio is in the view or program mode. • On steady = View mode • Blinking = Program mode Zone Bank 1 A B •• C • or or A = Radio is in Zone 1. B = Radio is in Zone 2. C = Radio is in Zone 3. Zone Bank 2 D E• F • or or • D = Radio is in Zone 4. E = Radio is in Zone 5. F = Radio is in Zone 6. Secure Operation • On = Secure operation. • Off = Clear operation. • Blinking = Receiving an encrypted voice call. LED Indicator The LED indicator shows the operational status of your radio. Solid red – Radio is transmitting. PICTURE TO BE REPLACED WITH APX 6000 MODEL 1.5 Blinking red – Radio is transmitting at low battery condition. Double blinking red – Radio is in Emergency Mode. Rapidly blinking red – Radio has failed the self test upon powering up or encountered a fatal error. Solid yellow – Channel is busy. Identifying Status Indicators Vote Scan Enabled The vote scan feature is enabled. Blinking yellow – Radio is receiving a secured transmission. Solid green – Radio is powering up, or is on a non-priority channel while in the Scan List Programming mode. Blinking green – Radio is receiving an individual or telephone call, or is on a Priority-Two channel while in the Scan List Programming mode. Rapidly blinking green – Radio is on a Priority-One channel while in the Scan List Programming mode. 13 English Intelligent Lighting Indicators This feature temporary changes the backlight of the top display screen to help signal that a radio event has occurred. Identifying Status Indicators Note: 14 English This feature must be preprogrammed by a qualified radio technician. Backlight Notification Orange Emergency Alerts When The radio initiates an emergency alarm or call. The radio receives an emergency alarm or call. The radio battery is low. Red Critical Alerts The radio is out of range. The radio enters failsoft mode. The radio is unable to establish a full connection with the system. The radio receives a private call. Green Call Alerts The radio receives a phone call. The radio receives a call alert. The radio receives a selective call. Alert Tones You Hear Short, Low-Pitched Tone Tone Name Radio Self Test Fail When radio fails its power-up self test. Reject When unauthorized request is made. Time-Out Timer Warning No ACK Received Individual Call Warning Tone Long, Low-Pitched Tone A Group of Low-Pitched Tones Heard Time-Out Timer Timed Out Talk Prohibit/PTT Inhibit Four seconds before time out. When radio fails to receive an acknowledgment. When radio is in an individual call for greater than 6 seconds without any activity. After time out. (When PTT button is pressed) transmissions are not allowed. Out of Range (When PTT button is pressed) the radio is out of range of the system. Invalid Mode When radio is on an unpreprogrammed channel. Busy Identifying Status Indicators An alert tone is a sound or group of sounds. Your radio uses alert tones to inform you of your radio’s conditions. The following table lists these tones and when they occur. When the system is busy. 15 English You Hear Tone Name Valid Key-Press Radio Self Test Pass Short, Medium-Pitched Tone Clear Voice Priority Channel Received Identifying Status Indicators Emergency Alarm Entry Central Echo Long, Medium-Pitched Tone Volume Set Emergency Exit Failsoft Automatic Call Back Talk Permit A Group of Medium-Pitched Tones 16 English Keyfail Console Acknowledge Received Individual Call Heard When correct key is pressed. When radio passes its power-up self test. At beginning of a non-coded communication. When activity on a priority channel is received. When entering the emergency state. When central controller has received a request from a radio. When volume is changed on a quiet channel. When exiting the emergency state. When the trunking system fails. When voice channel is available from previous request. (When PTT button is pressed) verifying system accepting transmissions. When encryption key has been lost. When status, emergency alarm, or reprogram request ACK is received. When Call Alert or Private Call is received. Call Alert Sent When Call Alert is received by the target radio. Site Trunking When a SmartZone trunking system fails. Tone Name Short, High-Pitched Tone (Chirp) Low-Battery Chirp Fast Ringing Ringing Heard When battery is below preset threshold value. When system is searching for target of Private Call. Enhanced Call Sent When waiting for target of Private Call to answer the call. Phone Call Received When a land-to-mobile phone call is received. Gurgle Dynamic Regrouping (When the PTT button is pressed) a dynamic ID has been received. Unique, Low-Pitched Chirp New Message When a new message is received. Unique, High-Pitched Chirp Priority Status When a priority message is received. Identifying Status Indicators You Hear 17 English Selecting a Zone General Radio Operation A zone is a group of channels. Once you understand how your APX 6000 Portable is configured, you are ready to use your radio. General Radio Operation Use this navigation guide to familiarize yourself with the basic Call features: Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Selecting a Radio Channel . . . . . . . . . . . . . . . . . . . . . Receiving and Responding to a Radio Call. . . . . . . . . Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . . . Repeater or Direct Operation . . . . . . . . . . . . . . . . . . . Monitoring Features . . . . . . . . . . . . . . . . . . . . . . . . . . PICTURE TO BE REPLACED WITH APX 6000 MODEL 1.5 page 18 page 19 page 19 page 22 page 22 page 23 Use the following procedure to select a zone. Note: Your radio must be preprogrammed to allow you to use this feature. Procedure: 1 Move the preprogrammed Zone (3-Position A/B/C) switch to the position of the required zone. 2 Press the PTT button to transmit on the displayed zone 18 English channel. Selecting a Radio Channel PICTURE TO BE REPLACED WITH APX 6000 MODEL 1.5 Once you have selected the required channel and/or zone, you can proceed to receive and respond to calls. PICTURE TO BE REPLACED WITH APX 6000 MODEL 1.5 Use the following procedure to select a channel. Note: Your radio must be preprogrammed to allow you to use this feature. If you select a channel that is not within the preprogrammed band, the radio indicates that it is on an unsupported frequency with an audio warning. Procedure: 1 Turn the preprogrammed 16-Position Select knob to the desired channel. General Radio Operation A channel is a group of radio characteristics, such as transmit/ receive frequency pairs. Receiving and Responding to a Radio Call The LED lights up solid red while the radio is transmitting, and solid yellow when the radio is receiving a transmission (conventional mode only). There is no LED indication when the radio receives a transmission in trunking mode. If the radio is receiving a secure transmission, the LED blinks yellow. 2 Press the PTT button to transmit on the displayed zone channel. 19 English Receiving and Responding to a Talkgroup Call To receive a call from a group of users, your radio must be configured as part of that talkgroup. Procedure: When you receive a talkgroup call (while on the Home screen), depending on how your radio is preprogrammed: General Radio Operation 1 ASTRO Conventional Only: The LED lights up solid yellow. OR Trunking Only: The display shows the caller alias or ID. 2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3 Press the PTT button to respond to the call. The LED lights up solid red. 4 Release the PTT button to listen. See Making a Talkgroup Call on page 22 for details on making a Talkgroup Call. 20 English Receiving and Responding to a Private Call (Trunking Only) A Private Call is a call from an individual radio to another individual radio. These one-to-one calls between two radios are not heard by others in the current talkgroup. The calling radio automatically verifies that the receiving radio is active on the system and can display the caller’s ID. Note: The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You will hear the Inactive Exit Tone upon feature exit. Procedure: When you receive a Private Call: 1 You hear two alert tones and the LED blinks green. The backlight of the screen turns green and the display shows CALL RCV, alternating with the caller alias (name) or ID (number). 2 Press the Call Response button within 20 seconds after the call indicators begin. button to listen. 4 Press the Call Response button to hang up and return to the Home screen. You cannot initiate a Private Call. Receiving and Responding to a Telephone Call (Trunking Only) This feature allows you to receive calls similar to standard phone calls from a landline phone. Note: The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You will hear the Inactive Exit Tone upon feature exit. 1 You hear a telephone-type ringing and the LED blinks green. The backlight of the screen turns green and the display shows PHN CALL. 2 Press the Call Response button within 20 seconds after the call indicators begin. 3 Press and hold the PTT button to talk. Release the PTT button to listen. 4 Press the Call Response button to hang up and return to the Home screen. You cannot initiate a Telephone Call. General Radio Operation 3 Press and hold the PTT button to talk. Release the PTT Procedure: When you receive a Telephone Call: 21 English Making a Radio Call You can select a zone, channel, or talkgroup by using: • The preprogrammed Zone switch • The Channel Selector Knob Making a Talkgroup Call General Radio Operation To make a call to a group of users, your radio must be configured as part of that talkgroup. 22 Procedure: 1 Turn the Channel Selector Knob to select the channel with the desired talkgroup. 2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3 Press the PTT button to make the call. 4 ASTRO Conventional Only: The LED lights up solid red. The display shows the talkgroup alias or ID. OR Trunking Only: The LED lights up solid red. 5 Speak clearly into the microphone. 6 Release the PTT button to listen. English Repeater or Direct Operation The REPEATER operation increases the radio’s range by connecting with other radios through a repeater. The transmit and receive frequencies are different. The DIRECT or “talkaround operation” allows you to bypass the repeater and connect directly to another radio. The transmit and receive frequencies are the same. Procedure: 1 Press the preprogrammed Repeater/Direct switch to toggle between talkaround and repeater modes. 2 The display shows RPTR MOD if the radio is currently in Repeater mode. OR The display shows DIR MODE and the Talkaround icon if the radio is currently in Direct mode (during conventional operation only). Monitoring Features Use the Monitor feature to make sure a channel is clear before transmitting. Monitoring a Channel Procedure: 1 Press the preprogrammed Monitor button. 2 Press and hold the Volume Set button to hear the volume Your radio may be preprogrammed to receive Private-Line® (PL) calls. Procedure: 1 Momentarily press the Monitor button to listen for activity. The Carrier Squelch indicator appears on the display. 2 Press and hold the Monitor button to set continuous monitor operation. The duration of the button press is programmable. 3 Press the Monitor button again, or the PTT button, to return to the original squelch setting. If you try to transmit on a receive-only channel, you hear an invalid tone until you release the PTT button. General Radio Operation Radio users who switch from analog to digital radios often assume that the lack of static on a digital channel is an indication that the radio is not working properly. This is not the case. Digital technology quiets the transmission by removing the “noise” from the signal and allowing only the clear voice or data information to be heard. Conventional Mode Operation set tone. 3 Adjust the Volume Control knob if necessary. 4 Release the Volume Set button. 5 Press and hold the PTT button to transmit. The LED lights up solid red. 6 Release the PTT button to receive (listen). The Carrier Squelch indicator appears on the display when you monitor a channel via the preprogrammed Monitor button. 23 English Advanced Features Advanced Features Use this navigation guide to learn more about advanced features available with your radio: Advanced Call Features . . . . . . . . . . . . . . . . . . . . . . . page 24 Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 26 Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 27 Call Alert Paging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 29 Emergency Operation . . . . . . . . . . . . . . . . . . . . . . . . . page 29 Secure Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . page 33 Trunking System Controls. . . . . . . . . . . . . . . . . . . . . . page 37 Utilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 41 24 English Advanced Call Features Receiving and Responding to a Selective Call (ASTRO Conventional Only) This feature allows you to receive a call from or to call a specific individual. It is intended to provide privacy and to eliminate the annoyance of having to listen to conversations that are of no interest to you. Procedure: 1 When you receive a Selective Call, you hear two alert tones and the LED lights up solid yellow. The backlight of the screen momentarily turns green and the display briefly shows CALL RCV. 2 The speaker unmutes. 3 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 4 Press and hold the PTT button to talk. Release the PTT button to listen. You cannot initiate a Selective Call. Using the Dynamic Regrouping Feature (Trunking Only) You will not notice whether your radio has this feature enabled until a dynamic regrouping command is sent by the dispatcher. Note: If you try to access a zone or channel that has been reserved by the dispatcher as a dynamically regrouped mode for other users, an invalid tone sounds. Procedure: 1 When your radio is dynamically regrouped, it automatically switches to the dynamically regrouped channel. A “gurgle” tone sounds and the display shows the dynamically regrouped channel’s name. This feature lets you notify the dispatcher that you want a new dynamic regrouping assignment. Procedure: 1 Press the preprogrammed Reprogram Request button to send reprogram request to the dispatcher. 2 The display alternates between RPGM and PLS WAIT. 3 If you hear five beeps, the dispatcher has acknowledged the reprogram request. The display shows ACK RCVD and the radio returns to the Home screen. OR If the dispatcher does not acknowledge the reprogram request within six seconds, a low-pitched alert tone sounds and the display shows NO ACK. The radio returns to the Home screen. Advanced Features This feature allows the dispatcher to temporarily reassign selected radios to a single special channel so they can communicate with each other. This feature is typically used during special operations and is enabled by a qualified radio technician. Requesting a Reprogram (Trunking Only) 2 Press the PTT button to talk. Release PTT button to listen. When the dispatcher cancels dynamic regrouping, the radio automatically returns to the zone and channel that you were using before the radio was dynamically regrouped. 25 English Classifying Regrouped Radios The dispatcher can classify regrouped radios into either of two categories: Select Enabled or Select Disabled. • Select-enabled radios are free to change to any available channel, including the dynamic-regrouping channel, once the user has selected the dynamic-regrouping position. • Select-disabled radios cannot change channels while dynamically regrouped. The dispatcher has forced the radio to remain on the dynamic-regrouping channel. The Scan or Private Call feature cannot be selected while your radio is Select Disabled. Scan Lists Scan lists are created and assigned to individual channels/ groups. Your radio scans for voice activity by cycling through the channel/group sequence specified in the scan list for the current channel/group. Your radio can support up to 125 different scan lists. These lists must be preprogrammed by a qualified radio technician. Viewing a Scan List Procedure: Advanced Features Turn the 16-Position Select knob to view the members on the list. 26 English Viewing and Changing the Priority Status Procedure: 1 Press the Top Side (Select) button to change the priority status of the currently displayed channel or the scan list status icon of the currently displayed channel. 2 A Scan icon indicates that the current channel is in the scan Scan This feature allows you to monitor traffic on different channels by scanning a preprogrammed list of channels. Turning Scan On or Off Procedure: 1 Press the preprogrammed Scan button, or turn the preprogrammed Scan switch to the Scan on or Scan off position. 2 The display shows SCAN ON and the scan icon, indicating that scan is enabled. OR The display shows SCAN OFF, indicating that scan is disabled. Advanced Features list as a non-priority channel. The LED lights up solid green. OR A Priority-Two Channel Scan icon indicates that the current channel is in the scan list as the Priority-Two channel. The LED blinks green. OR A Priority-One Channel Scan icon indicates that the current channel is in the scan list as the Priority-One channel. The LED rapidly blinks green. You hear all traffic on the PriorityOne channel, regardless of traffic on non-priority channels. OR No icon indicates that the current channel is deleted from the scan list. 27 English Making a Dynamic Priority Change (Conventional Note: Scan Only) While the radio is scanning, the dynamic priority change feature allows you to temporarily assign any channel in a scan list (except for the Priority-One channel) as the Priority-Two channel. This change remains in effect until scan is turned off. Scan then reverts to the preprogrammed (original) setting. Deleting a “nuisance” channel is only possible through the preprogrammed Nuisance Channel Delete button. Procedure: 1 When the radio is locked onto the channel to be deleted, press the preprogrammed Nuisance Delete button. 2 The radio continues scanning the remaining channels in the list. Procedure: 1 When the radio locks onto the channel designated as the Advanced Features new Priority-Two channel, press the preprogrammed Dynamic Priority button. 2 The radio continues scanning the remaining channels in the list. Deleting a Nuisance Channel If a channel continually generates unwanted calls or noise (termed a “nuisance” channel), you can temporarily remove the unwanted channel from the scan list. This capability does not apply to priority channels or the designated transmit channel. 28 English Restoring a Nuisance Channel Procedure: To restore the deleted nuisance channel, do one of the following: • Turn the radio off and then turning it on again. OR • Stop and restart a scan via the preprogrammed Scan button. OR • Change the channel via the 16-Position Select knob. Call Alert Paging Emergency Operation The Emergency feature is used to indicate a critical situation. Note: If the Top (Orange) button is preprogrammed to send an emergency signal, this signal overrides any other communication over the selected channel. This feature must be preprogrammed by a qualified radio technician. Receiving a Call Alert Page Procedure: 1 When you receive a Call Alert page, you hear four repeating alert tones and the LED blinks green. 2 The backlight of the screen turns green and the display briefly shows PAGE RCV. You cannot send a Call Alert page. Your radio supports the following Emergency modes: • Emergency Alarm • Emergency Call (Trunking Only) • Emergency Alarm with Emergency Call • Silent Emergency Alarm Advanced Features This feature allows your radio to work like a pager. Check with your dealer or system administrator for more information on the programming of this feature. Only one of the Emergency modes above can be assigned to the preprogrammed Emergency button. Note: To exit emergency at any time, press and hold the preprogrammed Emergency button for about a second. 29 English Sending an Emergency Alarm Sending an Emergency Call (Trunking Only) This feature allows you to send a data transmission, which identifies the radio sending the emergency, to the dispatcher. This feature gives your radio priority access on a channel. Procedure: 1 Press the preprogrammed Emergency button. 2 The display shows EMERGNCY and the current zone or channel. A short, medium-pitched tone sounds and the LED rapidly blinks red. OR An invalid tone sounds, if the selected channel does not support emergency. Advanced Features 3 When you receive the dispatcher’s acknowledgment, the display shows ACK RCVD. Four tones sound, the alarm ends, and the radio exits the Emergency Alarm mode. OR If no acknowledgement is received, the display shows NO ACK. The alarm ends and the radio exits the Emergency Alarm mode. 30 English Note: The radio operates in the normal dispatch manner while in Emergency Call, except, if enabled, it returns to one of the following: • Tactical/Non-Revert – You talk on the channel you selected before you entered the emergency state. • Non-Tactical/Revert – You talk on a preprogrammed emergency channel. The emergency alarm is sent on this same channel. Procedure: 1 Press the preprogrammed Emergency button. 2 The display shows EMERGNCY and the current zone or channel. A short, medium-pitched tone sounds and the LED rapidly blinks red. OR An invalid tone sounds, if the selected channel does not support emergency. 3 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. microphone. 5 Release the PTT button to end the transmission and wait for a response from the dispatcher. 6 Press and hold the preprogrammed Emergency button for about a second to exit the Emergency Call mode. You receive the dispatcher’s acknowledgment. The display shows ACK RCVD. OR You press the PTT button while in the Emergency Alarm mode. 4 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 5 Press and hold the PTT button. Speak clearly into the microphone. Sending an Emergency Alarm with Emergency Call Procedure: 1 Press the preprogrammed Emergency button. 6 Release the PTT button to end the transmission and wait for a response from the dispatcher. Advanced Features 4 Press and hold the PTT button. Speak clearly into the 3 The radio enters the Emergency Call state when: 7 Press and hold the preprogrammed Emergency button for about a second to exit the Emergency Call mode. 2 The display shows EMERGNCY and the current zone or channel. A short, medium-pitched tone sounds and the LED rapidly blinks red. OR An invalid tone sounds, if the selected channel does not support emergency. 31 English Sending a Silent Emergency Alarm Using the Emergency Keep-Alive Feature This feature allows you to send an Emergency Alarm to another radio without any audio or visual indicators. This feature, when enabled, prevents the radio from being turned off via the On/Off Control knob when the radio is in the Emergency state. Procedure: 1 Press the preprogrammed Emergency button. 2 The display shows no changes, the LED does not light up, and you hear no tones. Advanced Features 3 The silent emergency state continues until you: Press and hold the preprogrammed Emergency button for about a second to exit the Silent Emergency Alarm mode. OR Press and release the PTT button to exit the Silent Emergency Alarm mode and enter regular dispatch or Emergency Call mode. Note: 32 English For ALL Emergency signals, when changing channels: • If the new channel is also preprogrammed for Emergency, you can change channels while in Emergency operation. The emergency alarm or call continues on the new channel. • If the new channel is NOT preprogrammed for Emergency, the display shows NO EMERG, and you hear an invalid tone until you exit the Emergency state or change to a channel preprogrammed for Emergency. Note: The radio only exits the Emergency state using one of the ways mentioned in the previous sections. See Sending an Emergency Alarm on page 30, Sending an Emergency Call (Trunking Only) on page 30, Sending an Emergency Alarm with Emergency Call on page 31, or Sending a Silent Emergency Alarm on page 32. Advanced Secure Operations Unlike other forms of security, Motorola digital encryption provides signaling that makes it virtually impossible for others to decode any part of an encrypted message. Selecting Secure Transmissions Procedure: Turn the preprogrammed Secure/Clear switch to the secure position. Note: Procedure: Turn the preprogrammed Secure/Clear switch to the clear position. Note: If the selected channel is preprogrammed for secureonly operation – when you press the PTT button, an invalid mode tone sounds and the display shows SEC TX. The radio will not transmit until you set the Secure/ Clear switch to the secure position. Advanced Features Secure radio operation provides the highest commercially available level of voice security on both trunked and conventional channels. Selecting Clear Transmissions If the selected channel is preprogrammed for clear-only operation – when you press the PTT button, an invalid mode tone sounds and the display shows CLR TX. The radio will not transmit until you set the Secure/ Clear switch to the clear position. 33 English Managing Encryption Using the Multikey Feature Loading an Encryption Key This feature allows the radio to be equipped with as many as 48 different encryption keys and supports the DES-OFB algorithm. Note: There are two types: Refer to the key-variable loader (KVL) manual for equipment connections and setup. Procedure: 1 Attach the KVL to your radio. 2 The display shows KEYLOAD, and all other radio functions, except for power down, backlight, and volume, are locked out. Advanced Features 3 Select the required keys and press the Menu Select button directly below LOAD on the KVL. This loads the encryption keys into your radio. 4 When the key has been loaded successfully, the radio sounds a short tone for single-key radios. OR When the key has been loaded successfully, the radio sounds an alternating tone for multikey radios. 34 English • Conventional Multikey – The encryption keys can be tied (strapped), on a one-per-channel basis, through Customer Programming Software. In addition, you can have operatorselectable keys, operator-selectable keysets, and operatorselectable key erasure. If talkgroups are enabled in conventional, then the encryption keys are strapped to the talkgroups. • Trunked Multikey – If you use your radio for both conventional and trunked applications, you have to strap your encryption keys for trunking on a per-talkgroup or announcement-group basis. In addition, you may strap a different key to other features, such as dynamic regrouping, failsoft, or emergency talkgroup. You can have operatorselectable key erasure. Erasing the Selected Encryption Keys Procedure: Use the preprogrammed Top Side (Select) button and Top (Orange) button to erase the single key in radios with the single-key option, and to erase all keys in radios with the multikey option. 1 Press and hold the Top Side (Select) button. 2 While holding Top Side (Select) button down, press the Top (Orange) button. 3 The display shows PLS WAIT. 4 When all the encryption keys have been erased, the display shows ALL ERASED. Note: DO NOT press the Top (Orange) button before pressing the Top Side (Select) button, unless you are in an emergency situation as this sends an emergency alarm. Conventional Only) This feature, also known as OTAR, allows the dispatcher to reprogram the encryption keys in the radio remotely. The dispatcher performs the rekey operation upon receiving a rekey request from the user. Procedure: 1 Press and hold the preprogrammed Rekey Request button to send the rekey request. 2 If the rekey operation fails, a bad-key tone sounds and the display shows RKY FAIL. Note: Advanced Features This feature allows you to erase all or selected encryption keys. Requesting an Over-the-Air Rekey (ASTRO The rekey operation failure indicates that your radio does not contain the Unique Shadow Key (USK). This key must be loaded into the radio with the key-variable loader (KVL) before the rekey request can be sent. Refer to your local key management supervisor for more information. 35 English MDC Over-the-Air Rekeying (OTAR) Page Hear Clear This feature allows to view or define MDC Over-the-Air Rekeying (OTAR) features.It is applied only when operating in secure encrypted mode and only for conventional communications. In additional to Rekey Requests, OTAR transmissions include Delayed Acknowledgements, and Powerup Acknowledgements. There are two components of Hear Clear. Some of the options selected may also need to be set up at the Key Management Controller (KMC) site to work properly. Advanced Features Note: 36 English This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. 1 Companding: Reduces the channel noise, e.g. OTA transmission, that is predominantly present in UHF2 and 900 MHz channel with the following features. • Compressor – reduces the background noise flow and the speech signal at transmitting radio. • Expander – expands the speech while the noise flow remains the same at receiving radio. 2 Random FM Noise Canceller (Flutter Fighter): Reduces the unwanted effects of random FM noise pulses caused by channel fading under high Signal-to-Noise (S/N) conditions such as in a moving in a transportation. The fading effects, heard as audio pops and clicks, are cancelled without affecting the desired audio signal. The Random FM Noise Canceller operates only in receive mode. Note: This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. Trunking System Controls The failsoft system ensures continuous radio communications during a trunked system failure. If a trunking system fails completely, the radio goes into failsoft operation and automatically switches to its failsoft channel. Procedure: 1 During failsoft operation, your radio transmits and receives in conventional operation on a predetermined frequency. 2 A medium-pitched tone sounds every 10 seconds and the display shows FAILSOFT. When the trunking system returns to normal operation, your radio automatically leaves failsoft operation and returns to trunked operation. When your radio goes out of the range of the system, it can no longer lock onto a control channel. Procedure: 1 A low-pitched tone sounds. AND/OR The display shows the currently selected zone/channel combination and OUT RNG. 2 Your radio remains in this out-of-range condition until: It locks onto a control channel. OR It locks onto a failsoft channel. OR It is turned off. Advanced Features Using the Failsoft System Going Out of Range 37 English Using the Site Trunking Feature Viewing and Changing a Site If the zone controller loses communication with any site, that site reverts to site trunking. This feature allows you to view the number of the current site or force your radio to change to a new one. The display shows the currently selected zone/channel combination and STE TRNK. Viewing the Current Site Note: When this occurs, you can communicate only with other radios within your trunking site. Advanced Features Locking and Unlocking a Site This feature allows your radio to lock onto a specific site and not roam among wide-area talkgroup sites. This feature should be used with caution, since it inhibits roaming to another site in a wide-area system. Procedure: 1 Use the preprogrammed Site Lock/Unlock button to toggle the lock state between locked and unlocked. 2 The radio saves the new site lock state and returns to the Home screen. 38 English Procedure: 1 Press the preprogrammed Site Search button. 2 The display momentarily shows the name of the current site and its corresponding received signal strength indicator (RSSI). Changing the Current Site Procedure: 1 Press and hold down the preprogrammed Site Search button. 2 A tone sounds and the display momentarily shows SCANNING. 3 When the radio finds a new site, it returns to the Home screen. Bluetooth Turning on the Bluetooth Follow the steps below to turn on the Bluetooth. 1 Short press the programmable button to turn on the Bluetooth feature screen. 2 A good key tone sounds. The display shows BT ON and the Bluetooth icon. Turning off the Bluetooth Follow the steps below to turn off the Bluetooth. 1 Short press the programmable button to turn off the Bluetooth feature screen. 2 A good key tone sounds. The display shows BT OFF and the Bluetooth icon disappears. With your radio’s Bluetooth feature turned on, 1 Turn on the Bluetooth of the device then place it close to the radio. 2 If the pairing process is successful, the radio sounds a paired tone. OR If the pairing process fails, the radio sounds a bad bonk. The display shows PAIRFAIL. Repeat step 1 again. 3 The radio continues to connect to the device. If the connecting process is successful, the radio sounds a connected tone. The display showsalternates with CONNECT. OR If the connecting process fails, the radio sounds a bad bonk. The display shows alternates with CON FAIL. Repeat step 2 to reconnect the bluetooth. OR If the connecting process fails, the radio sounds a bad bonk. The display shows alternates with CON FAIL. After 5 minutes and the device is not re-connecting with the radio, the radio sounds a de-paired tone. The display shows alternates with DEPAIRED. Advanced Features This feature allows the radio user to pair Motorola proprietary headset with the radio. It enables the user to talk and listen using Motorola proprietary headset. User can also switch the audio between Bluetooth headset and radio easily. Pairing Bluetooth device with the Radio 39 English Indicating Bluetooth Connection is Lost Turning off the Bluetooth Audio Bluetooth icon is shown solid when the Bluetooth connection is strong. Below is the scenario and indications shown by your radio when the connection is interrupted. Follow the steps below to turn off the Bluetooth. 1 The Bluetooth icon starts flashing for 10 seconds. The radio sounds a disconnect tone and the display shows alternates with CON LOST. Advanced Features 2 If the Bluetooth device successfully re-connects before the time-out timer expires, the display shows alternates with CONNECT. OR If no reconnecting after the period, the alternates with CON LOST disappears and the Bluetooth icon becomes solid. Turning on the Bluetooth Audio Follow the steps below to turn on the Bluetooth Audio. 1 Short press the programmable button to turn on the Bluetooth feature screen. 2 A good key tone sounds. The display shows SPKR ON. 40 English 1 Short press the programmable button to turn off the Bluetooth feature screen. 2 A good key tone sounds. The display shows SPKR OFF. Adjusting the Volume of the radio from Bluetooth Audio Device With the Bluetooth audio device connecting to the radio, 1 Adjust volume up/down of the bluetooth audio device. 2 The radio display shows Volume XX and sounds Volume Changed Confirmation Tone. Utilities Procedure: Using the Flip Display This feature allows you to flip the content of the top display upside down. It is particularly useful when you would like to read the top display while the radio is still attached to your belt. Procedure: Press and hold the preprogrammed Light button to flip the display. position between Bank 1 and Bank 2. 2 The top display shows the status icons (A, B, C, D, E or F) or the zone name based on the bank and switch position selected. See Zone Bank 1 and Zone Bank 2 on page 13 for more information on the status icons. Selecting the Power Level Selecting a Zone Bank You can select the power level at which your radio transmits. The radio always turns on to the default setting. This feature allows twice as many zones to be accessed from a switch, doubling the amount of switch positions. Note: Note: Settings: The Zone Select feature must to be preprogrammed to the 3-position A-B-C switch, while the Zone Bank feature must be preprogrammed to any side button or Top (Orange) button before you can use this feature. Advanced Features 1 Use the preprogrammed Zone Bank button to toggle the This feature must be preprogrammed by a qualified radio technician. • Select Low for a shorter transmitting distance and to conserve power. • Select High for a longer transmitting distance. 41 English Procedure: Turning Voice Mute On or Off 1 Press the preprogrammed Transmit Power Level Switch You can enable and disable voice transmission, if needed. to toggle the power level between low and high power. 2 The display shows LOW PWR and the low power icon. OR The display shows HIGH PWR and the high power icon. Procedure: 1 Press the preprogrammed Voice Mute button to turn the feature off or on. 2 The display momentarily shows VMUT OFF, and a short tone Controlling the Display Backlight Advanced Features You can enable or disable the radio’s display backlight as needed, if poor light conditions make the display difficult to read. Procedure: Press the preprogrammed Light button to toggle the backlight on or off. OR Press any programmable radio controls or buttons to turn the backlight on. Note: 42 English The backlight remains on for a preprogrammed time before it automatically turns off completely or returns to the minimum backlight level. sounds, indicating that the feature is disabled. OR The display momentarily shows VMUT ON, and a short tone sounds, indicating that the feature is enabled. Using the Time-Out Timer This feature turns off your radio’s transmitter. You cannot transmit longer than the preset timer setting. If you attempt to do so, the radio automatically stops your transmission, and you hear a talk-prohibit tone. Note: You will hear a brief, low-pitched, warning tone four seconds before the transmission times out. Procedure: 1 Hold down the PTT button longer than the preprogrammed time. You hear a short, low-pitched warning tone, the transmission is cut-off, and the LED goes out until you release the PTT button. 2 Release the PTT button. The timer resets. 3 Press the PTT button to re-transmit. The time-out timer Using the Conventional Squelch Operation Features This feature filters out unwanted calls with low signal strength or channels that have a higher than normal background noise. Analog Options Tone Private Line (PL), Digital Private-Line (DPL), and carrier squelch can be available (preprogrammed) per channel. Mode Result Carrier squelch (C) You hear all traffic on a channel. PL or DPL The radio responds only to your messages. Advanced Features The timer is defaulted at 60 seconds, but it can be preprogrammed from 3 to 120 seconds, in 15-second intervals, or it can be disabled entirely for each radio mode, by a qualified radio technician. restarts and the LED lights up solid red. 43 English Digital Options Using the PL Defeat Feature One or more of the following options may be preprogrammed in your radio. Check with your dealer or system administrator for more information. This feature allows you to override any coded squelch (DPL or PL) that might be preprogrammed to a channel. The radio will also unmute to any digital activity on a digital channel. Option Advanced Features Digital Carrier-Operated Squelch (COS) 44 English Result You hear any digital traffic. Normal Squelch You hear any digital traffic having the correct network access code. Selective Switch You hear any digital traffic having the correct network access code and correct talkgroup. Procedure: Place the preprogrammed PL Defeat switch in the PL Defeat position. You hear any activity on the channel. OR The radio is muted if no activity is present. Note: When this feature is active, the Carrier Squelch status indicator is displayed. Using the Digital PTT ID Feature Your radio’s ID number is also automatically sent every time the PTT button is pressed. This is a per-channel feature. For digital voice transmissions, your radio’s ID is sent continuously during the voice message. Using the Smart PTT Feature (Conventional Only) Smart PTT is a per-personality, programmable feature used in conventional radio systems to keep radio users from talking over other radio conversations. When smart PTT is enabled in your radio, you cannot transmit on an active channel. Three variations of smart PTT are available: Transmit Inhibit on Busy Channel with Carrier You cannot transmit if any traffic is detected on the channel. Transmit Inhibit on Busy Channel with Wrong Squelch Code You cannot transmit on an active channel with a squelch code or (if secure-equipped) encryption key other than your own. If the PL code is the same as yours, the transmission is not prevented. Quick-Key Override This feature can work in conjunction with either of the two above variations. You can override the transmit-inhibit state by quick-keying the radio. In other words, two PTT button presses within the preprogrammed time limit. Advanced Features This feature allows you to see the radio ID (number) of the radio from whom you are currently receiving a transmission. This ID, consisting up to a maximum of eight characters, can be viewed by both the receiving radio and the dispatcher. If you try to transmit on an active smart-PTT channel, you hear an alert tone, and the transmission is inhibited. The LED lights up solid yellow to indicate that the channel is busy. 45 English Seek advice from your dealer or qualified technician for the best selections for this feature. Voice Announcement This feature enables the radio to audibly indicate the current feature mode, Zone or Channel the user has just assigned. This audio indicator can be customized per customer requirements. This is typically useful when the user is in a difficult condition to read the content shown on the display. Each voice announcement is within a limit of three seconds maximum. As much as 2000 unique voice announcements are allowed in a radio. The sum total duration for all voice announcements in a radio shall be no more than 1000 seconds. Advanced Features Note: This feature must be preprogrammed by a qualified radio technician. The features which Voice Announcement supports are: • Zone • Channel • Scan • PL Disabled • Talkaround/Direct • Tx Inhibit Note: Voice announcements support certain number of zonechannel, but not all. The two options of priority for the Voice Announcement available are: • High – enables the voice of the feature to announce even when the radio is receiving calls. • Low – disables the voice of the feature from announcing when the radio is receiving calls. Procedure: You hear a voice announcement when the features below are preprogrammed in the radio. • The radio powers up. The radio announces the current zone and channel it is transmiting. • Press the preprogrammed voice announcement button (which specifically programmed to playback the current zone and channel). The radio announces the current zone and channel it is transmitting. Note: Pressing this preprogrammed playback button will always enable the voice feature to announce in High priority. All the three programmable buttons at the side of the radio support this feature. • Change to a new zone. The radio announces the current 46 English zone and channel it is transmiting. • Change to a new channel remaining within the current zone. The radio announces the current channel. to launch or terminate Scan, PL Disabled, Talkaround/Direct or Transmit Inhibit. The radio announces the corresponding feature activation. Advanced Features • Press either the preprogrammed button or switch of the radio 47 English Caring for Your Radio Helpful Tips Take a moment to review the following: Caring for Your Radio . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning Your Radio . . . . . . . . . . . . . . . . . . . . . . . . Handling Your Radio . . . . . . . . . . . . . . . . . . . . . . . . Servicing Your Radio . . . . . . . . . . . . . . . . . . . . . . . . Taking Care of the Battery. . . . . . . . . . . . . . . . . . . . . . Checking the Battery Charge Status . . . . . . . . . . . . Battery Recycling and Disposal. . . . . . . . . . . . . . . . page 48 page 49 page 49 page 50 page 50 page 50 page 51 Caution • The APX 6000 radio casting has a vent port that allows for pressure equalization in the radio. Never poke this vent with any objects, such as needles, tweezers, or screwdrivers. This could create leak paths into the radio and the radio’s submergibility will be lost. PICTURE TO BE REPLACED WITH APX 6000 MODEL 1.5 Helpful Tips • (For APX 6000 R Radios Only) 48 English The APX 6000 R radio is designed to be submerged to a maximum depth of 6 feet, with a maximum submersion time of 2 hours. Exceeding either maximum limit may result in damage to the radio. Caution Elastomer technology materials used for seals in rugged portable radios can age with time and environmental exposure. Therefore, Motorola recommends that rugged radios be checked annually as a preventive measure in order to assure the watertight integrity of the radio. Motorola details the disassembly, test, and reassembly procedures along with necessary test equipment needed to inspect, maintain and troubleshoot radio seals in the radio’s service manual. • If the radio battery contact area has been submerged in water, dry and clean the radio battery contacts before attaching a battery to the radio. Otherwise, the water could short-circuit the radio. • If the radio has been submerged in water, shake the radio well so that any water that may be trapped inside the speaker grille and microphone port can be removed. Otherwise, the water will decrease the audio quality of the radio. • Do not disassemble the radio. This could damage radio seals and result in leak paths into the radio. Any radio maintenance should be performed only by a qualified radio technician. Cleaning Your Radio To clean the external surfaces of your radio: 1 Combine one teaspoon of mild dishwashing detergent to one gallon of water (0.5% solution). 2 Apply the solution sparingly with a stiff, non-metallic, shortbristled brush, making sure excess detergent does not get entrapped near the connectors, controls or crevices. Dry the radio thoroughly with a soft, lint-free cloth. Helpful Tips • (For APX 6000 R Radios Only) 3 Clean battery contacts with a lint-free cloth to remove dirt or grease. Caution Do not use solvents to clean your radio. Spirits may permanently damage the radio housing. Do not submerge the radio in the detergent solution. Handling Your Radio • Do not pound, drop, or throw the radio unnecessarily. Never carry the radio by the antenna. • Avoid subjecting the radio to an excess of liquids. Do not submerge the radio unless it is a ruggedized, APX 6000 R model. 49 English • Avoid subjecting the radio to corrosives, solvents or spirits. Taking Care of the Battery • Do not disassemble the radio. • Keep the accessory-connector cover in place until ready to use the connector. Replace the cover immediately once the accessory has been disconnected. Helpful Tips Servicing Your Radio Proper repair and maintenance procedures will assure efficient operation and long life for this product. A Motorola maintenance agreement will provide expert service to keep this and all other communication equipment in perfect operating condition. A nationwide service organization is provided by Motorola to support maintenance services. Through its maintenance and installation program, Motorola makes available the finest service to those desiring reliable, continuous communications on a contract basis. For a contract service agreement, please contact your nearest Motorola service or sales representative, or an authorized Motorola dealer. Express Service Plus (ESP) is an optional extended service coverage plan, which provides for the repair of this product for an additional period of either one or two years beyond the normal expiration date of the standard warranty. For more information about ESP, contact the Motorola Radio Support Center at 3761 South Central Avenue, Rockford, IL 61102 (800) 227-6772 / (847)725-4200. 50 English Checking the Battery Charge Status Your radio can indicate the battery’s charge status through: • the LED and sounds. • the fuel gauge icon on the display. LED and Sounds When your battery is low: • the LED blinks red when the PTT button is pressed. • you hear a low-battery “chirp” (short, high-pitched tone). Fuel Gauge Icon A blinking fuel gauge icon ( ) is displayed only when the battery voltage drops to low level. In this case, replace the battery with a fully charged one. Battery Recycling and Disposal 76% to 100% full In the U.S. and Canada, Motorola participates in the nationwide Rechargeable Battery Recycling Corporation (RBRC) program for NiCd battery collection and recycling. Many retailers and dealers participate in this program. 51% to 75% 26% to 50% 11% to 25% 10% or less (at 10%, the gauge begins blinking) For the location of the drop-off facility closest to you, access RBRC's Internet web site at www.rbrc.com or call 1-800-8BATTERY. This internet site and telephone number also provide other useful information concerning recycling options for consumers, businesses, and governmental agencies. Helpful Tips Battery Charge Gauge 51 English Accessories For a list of Motorola-approved antennas and other accessories, visit the following website: http://www.motorola.com/governmentandenterprise On the website, search for APX 6000 Multi-Band Portable Radio. You will see the accessories information besides the specifications of the radio. You can also contact your dealer for details. Contact your dealer for details. The certifications for the accessories are as below. VHF Band (FCC ID: AZ489FT3824) UHF Band (FCC ID: AZ489FT4899) Accessories 700/800 MHz Band (FCC ID: AZ489FT5859) Bluetooth Enabled Models: VHF Band (FCC ID: AZ489FT3829) UHF Band (FCC ID: AZ489FT4892) 700/800 MHz Band (FCC ID: AZ489FT5863) 52 English State the position of the vessel in distress, using any information that will help responders to locate you, e.g.: • latitude and longitude • bearing (state whether you are using true or magnetic north) • distance to a well-known landmark • vessel course, speed or destination State the nature of the distress. Specify what kind of assistance you need. State the number of persons on board and the number needing medical attention, if any. If you are in imminent and grave danger at sea and require emergency assistance, use VHF Channel 16 to send a distress call to nearby vessels and the United States Coast Guard. Transmit the following information, in this order: 1 “MAYDAY, MAYDAY, MAYDAY.” Mention any other information that would be helpful to responders, such as type of vessel, vessel length and/or tonnage, hull color, etc. “OVER.” 11 If you do not receive an immediate response, remain by the radio and repeat the transmission at intervals until you receive a response. Be prepared to follow any instructions given to you. Take a moment to review the following: Special Channel Assignments . . . . . . . . . . . . . . . . . . . page 53 Operating Frequency Requirements . . . . . . . . . . . . . . page 54 Special Channel Assignments Emergency Channel “THIS IS _____________________, CALL SIGN __________.” State the name of the vessel in distress 3 times, followed by the call sign or other identification of the vessel, stated 3 times. Repeat “MAYDAY” and the name of the vessel. “WE ARE LOCATED AT _______________________.” Appendix: Maritime Radio Use in the VHF Frequency Range Appendix: Maritime Radio Use in the VHF Frequency Range 10 Wait for a response. Non-Commercial Call Channel For non-commercial transmissions, such as fishing reports, rendezvous arrangements, repair scheduling, or berthing information, use VHF Channel 9. 53 English Appendix: Maritime Radio Use in the VHF Frequency Range Operating Frequency Requirements A radio designated for shipboard use must comply with Federal Communications Commission Rule Part 80 as follows: • on ships subject to Part II of Title III of the Communications Act, the radio must be capable of operating on the 156.800 MHz frequency • on ships subject to the Safety Convention, the radio must be capable of operating: • • in the simplex mode on the ship station transmitting frequencies specified in the 156.025 – 157.425 MHz frequency band, and in the semiduplex mode on the two frequency channels specified in the table below. Note: Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters. Additional information about operating requirements in the Maritime Services can be obtained from the full text of FCC Rule Part 80 and from the US Coast Guard. Table A-1: VHF Marine Channel List Frequency (MHz) Table A-1: VHF Marine Channel List (Continued) Frequency (MHz) Channel Number Transmit Receive 156.150 160.750 156.200 160.800 156.250 160.850 156.300 – 156.350 160.950 156.400 – 156.450 156.450 10 156.500 156.500 11 156.550 156.550 12 156.600 156.600 13** 156.650 156.650 14 156.700 156.700 15** 156.750 156.750 16 156.800 156.800 17** 156.850 156.850 18 156.900 161.500 156.950 161.550 Channel Number Transmit Receive 19 156.050 160.650 20 157.000 161.600 160.700 157.050 161.650 22 157.100 161.700 54 English 156.100 Table A-1: VHF Marine Channel List (Continued) Table A-1: VHF Marine Channel List (Continued) Frequency (MHz) Transmit 157.150 Frequency (MHz) Receive Channel Number Transmit Receive 161.750 75 *** *** 24 157.200 161.800 76 *** *** 25 157.250 161.850 77** 156.875 – 26 157.300 161.900 78 156.925 161.525 27 157.350 161.950 79 156.975 161.575 28 157.400 162.000 80 157.025 161.625 60 156.025 160.625 157.075 161.675 156.075 160.675 157.125 161.725 62 156.125 160.725 157.175 161.775 63 156.175 160.775 84 157.225 161.825 156.225 160.825 85 157.275 161.875 65 156.275 160.875 86 157.325 161.925 66 156.325 160.925 87 157.375 161.975 67** 156.375 156.375 88 157.425 162.025 68 156.425 156.425 69 156.475 156.475 71 156.575 156.575 72 156.625 – 73 156.675 156.675 74 156.725 156.725 Appendix: Maritime Radio Use in the VHF Frequency Range Channel Number Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters. ** Low power (1 W) only *** Guard band Note: A – in the Receive column indicates that the channel is transmit only. 55 English Term Glossary Carrier Squelch Feature that responds to the presence of an RF carrier by opening or unmuting (turning on) a receiver’s audio circuit. A squelch circuit silences the radio when no signal is being received so that the user does not have to listen to “noise.” Central Controller A software-controlled, computer-driven device that receives and generates data for the trunked radios assigned to it. It monitors and directs the operations of the trunked repeaters. Channel A group of characteristics such as transmit/ receive frequency pairs, radio parameters, and encryption encoding. This glossary is a list of specialized terms used in this manual. Glossary Term Definition Definition ACK Acknowledgment of communication. Active Channel A channel that has traffic on it. Analog Signal An RF signal that has a continuous nature rather than a pulsed or discrete nature. ARS Automatic Registration Service ASTRO 25 Trunking Motorola standard for wireless digital trunked communications. ASTRO Conventional Motorola standard for wireless digital conventional communications. Autoscan A feature that allows the radio to automatically scan the members of a scan list. In a trunking system, one of the channels that is used to provide a continuous, twoControl Channel way/data communications path between the central controller and all radios on the system. Call Alert Privately page an individual by sending an audible tone. Conventional Typically refers to radio-to-radio communications, sometimes through a repeater (see Trunking). Conventional Scan List A scan list that includes only conventional channels. 56 English Term Displayed by the radio after three failed attempts to unlock the radio.The radio must be powered off and on prior to another attempt. Digital Private Line (DPL) A type of coded squelch using data bursts. Similar to PL except a digital code is used instead of a tone. Digital Signal An RF signal that has a pulsed, or discrete, nature, rather than a continuous nature. Dispatcher An individual who has radio system management duties. Dynamic Regrouping A feature that allows the dispatcher to temporarily reassign selected radios to a single special channel so they can communicate with each other. Failsoft A feature that allows communications to take place even though the central controller has failed. Each trunked repeater in the system transmits a data word informing every radio that the system has gone into failsoft. FCC Frequency Modulation. It conveys information over a carrier wave by varying its frequency. Term Definition FM Frequency Modulation Hang Up Disconnect. Home screen The first display information after the radio completes its self test. KVL Key-variable loader: A device for loading encryption keys into the radio. LCD Liquid crystal display. LED Light-emitting diode. Monitor Check channel activity by pressing the Monitor button. If the channel is clear, you hear static. If the channel is in use, you hear conversation. It also serves as a way to check the volume level of the radio, since the radio “opens the squelch” when the monitor button is pressed. Multi-System Talkgroup Scan List A scan list that can include both talkgroups (trunked) and channels (conventional). Glossary Deadlock Definition Network Access Code (NAC) operates on Network Access digital channels to reduce voice channel Code interference between adjacent systems and sites. 57 English Glossary Term 58 Definition NiCd Nickel-cadmium NiMH Nickel-metal-hydride. Non-Tactical/ Revert The user talks on a preprogrammed emergency channel. The emergency alarm is sent out on this same channel. OTAR Over-the-air rekeying. Page A one-way alert, with audio and/or display messages. Personality A set of unique features specific to a radio. Preprogrammed Refers to a software feature that has been activated by a qualified radio technician. Term Repeater Definition A conventional radio feature, where you talk through a receive/transmit facility that re-transmits received signals, in order to improve communications range and coverage. Any digital P25 traffic having the correct Selective Switch Network Access Code and the correct talkgroup. Squelch Special electronic circuitry, added to the receiver of a radio, that reduces, or cuts off, unwanted signals before they are heard in the speaker. Private Line (PL) A sub-audible tone that is transmitted such that only receivers decoding the tone receives it. Standby An operating condition whereby the radio’s speaker is muted but still continues to receive data. Programmable Refers to a radio control that can have a radio feature assigned to it. Status Calls Pre-defined text messages that allow the user to send a conditional message without talking. PTT Push-To-Talk – the PTT button engages the transmitter and puts the radio in transmit (send) operation when pressed. Tactical/ Non-Revert The user talks on the channel that was selected before the radio entered the emergency state. Radio Frequency (RF) The part of the general frequency spectrum between the audio and infrared light regions (about 10 kHz to 10,000,000 MHz). Talkaround Bypass a repeater and talk directly to another unit for easy local unit-to-unit communications. English Term Definition An organization or group of radio users who communicate with each other using the same communication path. Trunking The automatic sharing of communications paths between a large number of users (see Conventional). Trunking Priority Monitor Scan List A scan list that includes talkgroups that are all from the same trunking system. USK Unique Shadow Key. Zone A grouping of channels. Glossary Talkgroup 59 English Product manufactured by MOTOROLA. MOTOROLA assumes no obligations or liability for additions or modifications to this warranty unless made in writing and signed by an officer of MOTOROLA. Commercial Warranty Limited Warranty MOTOROLA COMMUNICATION PRODUCTS Commercial Warranty I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG: 60 MOTOROLA INC. (“MOTOROLA”) warrants the MOTOROLA manufactured Communication Products listed below (“Product”) against defects in material and workmanship under normal use and service for a period of time from the date of purchase as scheduled below: ASTRO APX 6000 Portable Units One (1) Year Product Accessories One (1) Year MOTOROLA, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it (with a new or reconditioned Product), or refund the purchase price of the Product during the warranty period provided it is returned in accordance with the terms of this warranty. Replaced parts or boards are warranted for the balance of the original applicable warranty period. All replaced parts of Product shall become the property of MOTOROLA. This express limited warranty is extended by MOTOROLA to the original end user purchaser only and is not assignable or transferable to any other party. This is the complete warranty for the English Unless made in a separate agreement between MOTOROLA and the original end user purchaser, MOTOROLA does not warrant the installation, maintenance or service of the Product. MOTOROLA cannot be responsible in any way for any ancillary equipment not furnished by MOTOROLA which is attached to or used in connection with the Product, or for operation of the Product with any ancillary equipment, and all such equipment is expressly excluded from this warranty. Because each system which may use the Product is unique, MOTOROLA disclaims liability for range, coverage, or operation of the system as a whole under this warranty. II. GENERAL PROVISIONS: This warranty sets forth the full extent of MOTOROLA'S responsibilities regarding the Product. Repair, replacement or refund of the purchase price, at MOTOROLA’s option, is the exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. IN NO EVENT SHALL MOTOROLA BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY. This warranty gives specific legal rights, and there may be other rights which may vary from state to state. IV. HOW TO GET WARRANTY SERVICE: You must provide proof of purchase (bearing the date of purchase and Product item serial number) in order to receive warranty service and, also, deliver or send the Product item, transportation and insurance prepaid, to an authorized warranty service location. Warranty service will be provided by MOTOROLA through one of its authorized warranty service locations. If you first contact the company which sold you the Product (e.g., dealer or communication service provider), it can facilitate your obtaining warranty service. You can also call MOTOROLA at 1-800-927-2744 US/Canada. V. WHAT THIS WARRANTY DOES NOT COVER: A) Defects or damage resulting from use of the Product in other than its normal and customary manner. B) Defects or damage from misuse, accident, water, or neglect. Commercial Warranty III. STATE LAW RIGHTS: C)Defects or damage from improper testing, operation, maintenance, installation, alteration, modification, or adjustment. D)Breakage or damage to antennas unless caused directly by defects in material workmanship. E) A Product subjected to unauthorized Product modifications, disassembles or repairs (including, without limitation, the addition to the Product of non-MOTOROLA supplied equipment) which adversely affect performance of the Product or interfere with MOTOROLA's normal warranty inspection and testing of the Product to verify any warranty claim. F) Product which has had the serial number removed or made illegible. G)Rechargeable batteries if: (1) any of the seals on the battery enclosure of cells are broken or show evidence of tampering. (2) the damage or defect is caused by charging or using the battery in equipment or service other than the Product for which it is specified. H)Freight costs to the repair depot. I) A Product which, due to illegal or unauthorized alteration of the software/firmware in the Product, does not function in accordance with MOTOROLA’s published specifications or the FCC certification labeling in effect for the Product at the time the Product was initially distributed from MOTOROLA. J) Scratches or other cosmetic damage to Product surfaces that does not affect the operation of the Product. K) Normal and customary wear and tear. 61 English Commercial Warranty VI. PATENT AND SOFTWARE PROVISIONS: MOTOROLA will defend, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a United States patent, and MOTOROLA will pay those costs and damages finally awarded against the end user purchaser in any such suit which are attributable to any such claim, but such defense and payments are conditioned on the following: A) that MOTOROLA will be notified promptly in writing by such purchaser of any notice of such claim; B) that MOTOROLA will have sole control of the defense of such suit and all negotiations for its settlement or compromise; and C)should the Product or parts become, or in MOTOROLA’s opinion be likely to become, the subject of a claim of infringement of a United States patent, that such purchaser will permit MOTOROLA, at its option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non-infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by MOTOROLA. 62 English MOTOROLA will have no liability with respect to any claim of patent infringement which is based upon the combination of the Product or parts furnished hereunder with software, apparatus or devices not furnished by MOTOROLA, nor will MOTOROLA have any liability for the use of ancillary equipment or software not furnished by MOTOROLA which is attached to or used in connection with the Product. The foregoing states the entire liability of MOTOROLA with respect to infringement of patents by the Product or any parts thereof. Laws in the United States and other countries preserve for MOTOROLA certain exclusive rights for copyrighted MOTOROLA software such as the exclusive rights to reproduce in copies and distribute copies of such MOTOROLA software. MOTOROLA software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modified in any way, or used to produce any derivative thereof. No other use including, without limitation, alteration, modification, reproduction, distribution, or reverse engineering of such MOTOROLA software or exercise of rights in such MOTOROLA software is permitted. No license is granted by implication, estoppel or otherwise under MOTOROLA patent rights or copyrights. VII. GOVERNING LAW: This Warranty is governed by the laws of the State of Illinois, U.S.A. Notes Notes 63 English Notes 64 English Motorola, Inc. 1301, E. Algonquin Rd. Schaumburg, IL 60196-1078, U.S.A. MOTOROLA and the Stylized M Logo are registered in the U.S. Patent and Trademark Office. All other product or service names are the property of their respective owners. © 2010 Motorola, Inc. All rights reserved. June 2010. *68012001081* 68012001081-A
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Page Mode : UseOutlines XMP Toolkit : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:39 Producer : Acrobat Distiller 7.0 (Windows) Creator Tool : FrameMaker 8.0 Modify Date : 2010:11:10 13:14:14-05:00 Create Date : 2010:06:17 16:38:50Z Metadata Date : 2010:11:10 13:14:14-05:00 Format : application/pdf Title : APX 6000 M1.5 Portable Radio User Guide Creator : Motorola Document ID : uuid:fd29fc39-925e-4104-9e63-173ea28198d9 Instance ID : uuid:2d7c4d41-9e7d-4978-9133-13feebb2e792 Page Count : 78 Author : MotorolaEXIF Metadata provided by EXIF.tools