Motorola Solutions 92FT7037 MOBILE 2-WAY RADIO User Manual APX 7500 05 UG

Motorola Solutions, Inc. MOBILE 2-WAY RADIO APX 7500 05 UG

Contents

USERS MANUAL

Download: Motorola Solutions 92FT7037 MOBILE 2-WAY RADIO User Manual APX 7500 05 UG
Mirror Download [FCC.gov]Motorola Solutions 92FT7037 MOBILE 2-WAY RADIO User Manual APX 7500 05 UG
Document ID1195468
Application ID8NaCpjtWlDZvAM/yxlLwDA==
Document DescriptionUSERS MANUAL
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize224.89kB (2811093 bits)
Date Submitted2009-11-06 00:00:00
Date Available2009-11-06 00:00:00
Creation Date2009-10-13 09:37:33
Producing SoftwareAcrobat Distiller 7.0 (Windows)
Document Lastmod2009-11-06 14:25:24
Document TitleAPX 7500 05 UG
Document CreatorFrameMaker 8.0
Document Author: Penang GCD

m
Radio On/Off
ASTRO® APX™ 7500 Series
O5 Control Head
Digital Mobile Radio
Quick Reference Card
Press the Power On/Off button to toggle the power on
or off.
Adjusting Volume
Product Safety and RF Exposure Compliance
Caution
Before using this product, read the operating
instructions for safe usage contained in the Product
Safety and RF Exposure booklet enclosed with your
radio.
ATTENTION!
This radio is restricted to occupational use only to satisfy FCC RF
energy exposure requirements. Before using this product, read
the RF energy awareness information and operating instructions
in the Product Safety and RF Exposure booklet enclosed with
your radio (Motorola Publication part number 6881095C98) to
ensure compliance with RF energy exposure limits.
Radio Controls
Volume Knob
Dim Button
Home Button
Power On/Off Button
Indicators
Mode Knob
© 2009 by Motorola, Inc. All Rights Reserved. 10/09
1301 E. Algonquin Rd., Schaumburg,
IL 60196-1078, U.S.A.
Take the control head off hook.
Select zone/channel.
Listen for a transmission.
OR
Turn the Volume Knob.
OR
> or < to MON then press the Menu Select button
directly below MON and listen for activity.
Adjust volume, if necessary.
Press the PTT button to transmit; release to receive.
Turn the Volume Knob clockwise to increase volume or
counterclockwise to decrease the volume.
Selecting a Zone
1 > or < to ZONE.
Press and hold the PTT button. Speak clearly into
the microphone.
Sending an Emergency Alarm
3 > or < button until the desired zone is displayed.
Press H or the PTT button to confirm the selected
zone number.
Press the preprogrammed Emergency button. A
tone sounds and the display alternates EMERGENCY
and the home display.
Press the PTT button to begin transmitting on the
displayed zone channel.
A dispatcher acknowledgment ACK RECEIVED
display follows.
AND, Trunking Only:
A high-pitched tone indicates that the alarm has been
received by the trunked system’s central controller.
Press and hold the emergency button or the PTT
button to return to normal operation.
Orange
Button
_______
LED Indicators
Menu Entries
Navigation
Menu Select Button
Button
Accessory Port (Microphone)
Receiving and Transmitting
Selecting a Channel
Press and hold > to scroll to CHAN and press the
Menu Select button directly below CHAN. The
display shows the current zone and channel.
Rotate the Mode knob to the desired channel.
Press H or the PTT button to confirm the channel.
Press the PTT button to transmit on the displayed
zone channel.
To exit emergency at any time, press and hold the
Emergency button.
*PMLN5592A*
PMLN5592A
English
Sending an Emergency Call (Trunking Only)
Press preprogrammed Emergency button.
A tone sounds and the display alternates
EMERGENCY and the home display.
OR
A talk prohibited tone sounds when the selected
channel does not support emergency.
Press and hold the PTT button. Speak clearly into
the microphone.
Release the PTT to end the transmission.
To exit emergency at any time, press and hold the
Emergency button.
Sending a Silent Emergency Alarm
Press the preprogrammed Emergency button to
activate the silent alarm feature.
The display does not change; the LED does not light
up, and there is no tone.
Direct radio-to-radio communication or
communication through a repeater.
On = Direct
Off = Repeater
This channel is being monitored.
Voice muting the affiliated trunking talkgroup
or selected conventional channel.
On = Enabled
Off = Disabled
H .
OR
L = Radio is set at Low power.
H = Radio is set at High power.
Radio is in the view or program mode.
On steady = View mode.
Blinking = Program mode.
If silent emergency alarm is used with emergency call,
pressing the PTT button exits the silent mode and
initiates the emergency call.
On = Secure operation.
Off = Clear operation.
Blinking = Receiving an encrypted voice
call.
On = AES Secure operation.
Off = Clear operation.
Blinking = Receiving an encrypted voice
call.
On = Location feature enabled, and location
signal available.
Off = Location feature disabled.
Blinking = Location feature enabled, but
location signal unavailable.
On = User is currently associated with the
radio.
Off = User is currently not associated with
the radio.
Blinking = Device registration or user
registration with the server
failed due to an invalid
username or pin.
Data activity is present.
Scanning a scan list.
Blinking dot = Detects activity on the
Priority-One Channel during
scan.
Steady dot = Detects activity on the PriorityTwo Channel during scan.
The vote scan feature is enabled.
Display Status Icons
Receiving a call or data.
Transmitting a call or data.
Received an Individual Call.
The more stripes, the stronger the signal
strength for the current site (trunking only).
English
Menu Navigation
< or > to Menu Entry.
g directly below Menu Entry to
select.
< or > to scroll through sub-list.
H to exit.
g directly below Menu Entry to
select.
Declaration of Conformity
DECLARATION OF CONFORMITY
Per FCC CFR 47 Part 2 Section 2.1077(a)
Responsible Party
Name: Motorola, Inc.
Address: Motorola, Inc. 1301 E. Algonquin Rd.Schaumburg, IL60196-1078, U.S.A.
Phone Number: 1-800-927-2744
Declaration of Conformity
This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below.
Hereby declares that the product:
Model Name: APX 7500
conforms to the following regulations:
FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a)
Class B Digital Device
As a personal computer peripheral, this device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
English
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
Declaration of Conformity
• Increase the separation between the equipment and receiver.
ii
English
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Contents
Turning On the Radio . . . . . . . . . . . . . . . . . . . . . . . . 3
Validating Compatibility During Power Up . . . . . . . . 4
Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . 4
Declaration of Conformity . . . . . . . . . . . . . . . . . .i
Identifying Radio Controls . . . . . . . . . . . . . . . . .5
Important Safety Information . . . . . . . . . . . . . .ix
Radio Parts and Controls . . . . . . . . . . . . . . . . . . . . . 5
O5 Control Head and Microphone . . . . . . . . . . . . . 5
Product Safety and RF Exposure Compliance . . . . ix
Software Version . . . . . . . . . . . . . . . . . . . . . . . .ix
Computer Software Copyrights . . . . . . . . . . . . x
Documentation Copyrights . . . . . . . . . . . . . . . . x
Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . 1
How to Use This User Guide . . . . . . . . . . . . . . . . . . 1
Notations Used in This Manual . . . . . . . . . . . . . . . . . 1
What Your Dealer/System Administrator
Can Tell You . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Contents
This User Guide contains all the information you need
to use the APX™ 7500 Series Digital Mobile Radios.
Preparing Your Radio for Use . . . . . . . . . . . . . .3
Programmable Features . . . . . . . . . . . . . . . . . . . . . . 6
Assignable Radio Functions . . . . . . . . . . . . . . . . . . 6
Assignable Settings or Utility Functions . . . . . . . . . . 8
Accessing the Preprogrammed Functions . . . . . . . . 9
Using the Menu Select Buttons . . . . . . . . . . . . . . . . 9
Using the Advance Programmable Buttons . . . . . . . 9
Using the Navigation Buttons . . . . . . . . . . . . . . . . 10
Home Button . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data Feature Button . . . . . . . . . . . . . . . . . . . . . . .
4-Way Navigation Button . . . . . . . . . . . . . . . . . . .
Volume Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode Knob
............................
10
10
10
10
10
Using the Keypad
. . . . . . . . . . . . . . . . . . . . . 11
Keypad Characters – Uppercase Mode . . . . . . . . . 11
Keypad Characters – Lowercase Mode . . . . . . . . . 12
Keypad Characters – Numeric Mode . . . . . . . . . . . 13
Keypad Characters – Hexadecimal Mode . . . . . . . 14
iii
English
Push-To-Talk (PTT) Button
. . . . . . . . . . . . . . . . . 15
Repeater or Direct Operation . . . . . . . . . . . . . . . . . 32
Identifying Status Indicators . . . . . . . . . . . . . .15
Monitoring Features . . . . . . . . . . . . . . . . . . . . . . . . 32
Monitoring a Channel . . . . . . . . . . . . . . . . . . . . . . .32
Conventional Mode Operation . . . . . . . . . . . . . . . .33
Status Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Text Messaging Service (TMS) Icons . . . . . . . . . . 18
Status Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
TMS Menu Options
. . . . . . . . . . . . . . . . . . . . . . 19
LED Indicator
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Intelligent Lighting Indicators
Alert Tones
. . . . . . . . . . . . . . . 21
Advanced Call Features . . . . . . . . . . . . . . . . . . . . . 34
Calling a Phone Not in the List . . . . . . . . . . . . . . . .34
Receiving and Making a Selective Call
(Conventional Only) . . . . . . . . . . . . . . . . . . . . . . . .35
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Receiving a Selective Call . . . . . . . . . . . . . . . . . . .35
Making a Selective Call . . . . . . . . . . . . . . . . . . . . .35
General Radio Operation . . . . . . . . . . . . . . . . .25
Using the Talkgroup Call Feature (Conventional
Operation Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Selecting a Radio Channel . . . . . . . . . . . . . . . . . . . 26
Contents
Advanced Features . . . . . . . . . . . . . . . . . . . . . 34
Receiving and Responding to a Radio Call . . . . . . 26
Receiving and Responding to a Talkgroup Call . . . 27
Receiving and Responding to a Private Call
(Trunking Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Receiving and Responding to a Telephone Call . . 28
Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . 29
Making a Talkgroup Call . . . . . . . . . . . . . . . . . . . . . 29
Making a Private Call (Trunking Only) . . . . . . . . . . 30
Making a Telephone Call . . . . . . . . . . . . . . . . . . . . 31
iv
English
Selecting a Talkgroup . . . . . . . . . . . . . . . . . . . . . . .36
Sending a Status Call . . . . . . . . . . . . . . . . . . . . . . .37
Using the Dynamic Regrouping Feature
(Trunking Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Requesting a Reprogram . . . . . . . . . . . . . . . . . . . .38
Classifying Regrouped Radios . . . . . . . . . . . . . . . .38
Multiple Control Head Features . . . . . . . . . . . . . . . 39
Multiple Control Head Features . . . . . . . . . . . . . . .39
Setting the Initial Control Head’s ID . . . . . . . . . . . .39
All Active Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Intercom Feature in All Active Mode . . . . . . . . . . .40
One Active Mode . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Editing an Entry Alias . . . . . . . . . . . . . . . . . . . . . . . 46
Editing as Entry ID . . . . . . . . . . . . . . . . . . . . . . . . . 46
Editing a Call Type . . . . . . . . . . . . . . . . . . . . . . . . . 47
Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Viewing a Scan List . . . . . . . . . . . . . . . . . . . . . . . . .48
Editing the Scan List . . . . . . . . . . . . . . . . . . . . . . . .48
Changing the Scan List Status . . . . . . . . . . . . . . . .49
Viewing and Changing the Priority Status . . . . . . . .50
Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Turning Scan On or Off . . . . . . . . . . . . . . . . . . . . . .50
Turning Scan On While Disregarding the
Squelch Code (Conventional Channels Only) . . . . .51
Transmitting While the Scan is On . . . . . . . . . . . . .51
Radio Programmed for Talkback Scan . . . . . . . . . 51
Radio Programmed for Non-Talkback Scan . . . . . 51
Deleting a Nuisance Channel . . . . . . . . . . . . . . . . .52
Restoring a Nuisance Channel . . . . . . . . . . . . . . . .52
Changing Priorities Status While Scan is On . . . . .52
Restoring Priorities in a Scan List . . . . . . . . . . . . . .53
Hang Up (HUB) . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Call Alert Paging . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Receiving a Call Alert Page . . . . . . . . . . . . . . . . . . 54
Sending a Call Alert Page . . . . . . . . . . . . . . . . . . . 54
In-Call User Alert . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Emergency Operation . . . . . . . . . . . . . . . . . . . . . . . 56
Sending an Emergency Alarm . . . . . . . . . . . . . . . . 56
Sending an Emergency Call (Trunking Only) . . . . 57
Sending an Emergency Alarm with Emergency
Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Sending a Silent Emergency Alarm . . . . . . . . . . . . 58
Special Considerations for Emergencies . . . . . . . . 58
Contents
Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Making a Private Call from Contacts . . . . . . . . . . . .42
Adding a New Contact Entry . . . . . . . . . . . . . . . . . .44
Deleting a Contact Entry . . . . . . . . . . . . . . . . . . . . .45
Adding a Contact to a Call List or Phone List . . . . .45
Editing a Contact in a Call List or a Phone List . . . .46
Automatic Registration Service (ARS) . . . . . . . . . . 59
Selecting or Changing ARS Mode . . . . . . . . . . . . . 59
Accessing the User Login Feature . . . . . . . . . . . . . 60
Logging In as a User . . . . . . . . . . . . . . . . . . . . . . . 60
Logging Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Text Messaging Service (TMS) . . . . . . . . . . . . . . . . 62
Accessing TMS Feature . . . . . . . . . . . . . . . . . . . . 62
Composing and Sending a New Text Message . . . 63
Sending a Quick Text Message . . . . . . . . . . . . . . . 64
Using the Priority Status and Request Reply
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Appending or Removing a Priority Status to
a Text Message . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Appending or Removing a Request Reply to
a Text Message . . . . . . . . . . . . . . . . . . . . . . . . . . 66
English
Appending a Priority Status and a Reply
Request to a Text Message . . . . . . . . . . . . . . . . . . 66
Removing a Priority Status and a Reply
Request from a Text Message . . . . . . . . . . . . . . . . 67
Managing Text Messages . . . . . . . . . . . . . . . . . . . 67
Receiving a Text Message . . . . . . . . . . . . . . . . . . 67
Viewing a Text Message from the Inbox . . . . . . . . 68
Replying to a Received Text Message . . . . . . . . . 69
Accessing the Drafts Folder . . . . . . . . . . . . . . . . . . 70
Managing Sent Text Messages . . . . . . . . . . . . . . . 70
Viewing a Sent Text Message . . . . . . . . . . . . . . . . 70
Sending a Sent Text Message . . . . . . . . . . . . . . . 71
Deleting Text Messages . . . . . . . . . . . . . . . . . . . . 72
Contents
Secure Operations . . . . . . . . . . . . . . . . . . . . . . . . . 72
Managing Encryption . . . . . . . . . . . . . . . . . . . . . . . 72
vi
Loading a Single Encryption Key . . . . . . . . . . . . . . 72
Loading the Group Encryption Keys . . . . . . . . . . . 73
Using the Multikey Feature . . . . . . . . . . . . . . . . . . 73
Selecting an Encryption Key (Conventional Only) . 74
Enabling Secure Transmission . . . . . . . . . . . . . . . 74
Accessing the Secure Feature . . . . . . . . . . . . . . . 74
Selecting a Keyset . . . . . . . . . . . . . . . . . . . . . . . . . 75
Erasing the Selected Encryption Keys . . . . . . . . . . 75
Requesting an Over-the-Air Rekey . . . . . . . . . . . . 76
The Global Positioning System (GPS) . . . . . . . . . . 76
Understanding the GPS Feature . . . . . . . . . . . . . . 76
Enhancing GPS Performance . . . . . . . . . . . . . . . . 77
English
The Outdoor Location Feature (Using GPS) . . . . . .77
Accessing the Outdoor Location Feature . . . . . . . .78
Saving a Waypoint . . . . . . . . . . . . . . . . . . . . . . . . .79
Viewing a Saved Waypoint . . . . . . . . . . . . . . . . . . .80
Editing the Alias of a Waypoint . . . . . . . . . . . . . . . .80
Editing the Coordinates of a Waypoint . . . . . . . . . .81
Deleting a Single Saved Waypoint . . . . . . . . . . . . .82
Deleting All Saved Waypoints . . . . . . . . . . . . . . . .82
Measuring the Distance and Bearing from
a Saved Waypoint . . . . . . . . . . . . . . . . . . . . . . . . .83
Using the Location Feature While in Emergency
Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Trunking System Controls . . . . . . . . . . . . . . . . . . . 84
Using the Failsoft System . . . . . . . . . . . . . . . . . . . .84
Going Out-of-Range . . . . . . . . . . . . . . . . . . . . . . . .84
SmartZone® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Using Site Trunking Feature . . . . . . . . . . . . . . . . . .85
Locking and Unlocking a Site . . . . . . . . . . . . . . . . .85
Viewing and Changing a Site . . . . . . . . . . . . . . . . .86
Viewing the Current Site . . . . . . . . . . . . . . . . . . . . .86
Changing the Current Site . . . . . . . . . . . . . . . . . . .86
Trunked Announcement . . . . . . . . . . . . . . . . . . . . .87
Initiating an Announcement . . . . . . . . . . . . . . . . . .87
Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Viewing Recent Calls List . . . . . . . . . . . . . . . . . . . .88
Selecting the Power Level . . . . . . . . . . . . . . . . . . . .88
Selecting a Radio Profile . . . . . . . . . . . . . . . . . . . . .89
Helpful Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Analog Options . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Digital Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Control Station . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Using the PL Defeat Feature . . . . . . . . . . . . . . . . . .92
Using the Digital PTT ID Feature . . . . . . . . . . . . . .92
Using the Smart PTT Feature
(Conventional Only) . . . . . . . . . . . . . . . . . . . . . . . .93
Accessing General Radio Information . . . . . . . . . . .93
Accessing Radio Information . . . . . . . . . . . . . . . . . 93
Viewing IP Information . . . . . . . . . . . . . . . . . . . . . . 94
Viewing Control Assignments . . . . . . . . . . . . . . . . 95
Optional External Alarms (Horn and Lights) . . . . . .95
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Contents
Controlling the Display Backlight . . . . . . . . . . . . . . .89
Turning Keypad Tones On or Off . . . . . . . . . . . . . .90
Turning Voice Mute On or Off . . . . . . . . . . . . . . . . .90
Using the Time-Out Timer . . . . . . . . . . . . . . . . . . . .91
Using the Conventional Squelch Operation
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Footswitches and PTTs . . . . . . . . . . . . . . . . . . . . 102
Direct Entry Keypad and Siren . . . . . . . . . . . . . . . 102
Microphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Motorcycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Mounting Solution . . . . . . . . . . . . . . . . . . . . . . . . . 104
Power/CAN Cables . . . . . . . . . . . . . . . . . . . . . . . 104
Programming/Accessory Cables . . . . . . . . . . . . . . 105
Non-Permanent Horn and Lights . . . . . . . . . . . . . . 95
Permanent Horn and Lights . . . . . . . . . . . . . . . . . . 96
Changing the Selected Alarms . . . . . . . . . . . . . . . 96
Receiving a Call While Alarms are Turned On . . . . 97
Turning Off Non-Rearmable External Alarms . . . . 97
Turning Off Rearmable External Alarms . . . . . . . . 97
Appendix: Maritime Radio Use in the VHF
Frequency Range . . . . . . . . . . . . . . . . . . . . . .106
Voice Announcement . . . . . . . . . . . . . . . . . . . . . . .98
Operating Frequency Requirements . . . . . . . . . . . 107
Special Channel Assignments . . . . . . . . . . . . . . . 106
Emergency Channel . . . . . . . . . . . . . . . . . . . . . . 106
Non-Commercial Call Channel . . . . . . . . . . . . . . 106
vii
English
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109
Contents
Commercial Warranty and Service . . . . . . . .113
viii
English
Important Safety Information
Caution
Before using this product, read the operating
instructions for safe usage contained in the
Product Safety and RF Exposure booklet
enclosed with your radio.
All the features described in the following sections are
supported by the radio's software version R02.00.00 or
later.
Accessing Radio Information on page 93 to determine
your radio's software version.
Check with your dealer or system administrator for more
details of all the features supported.
ATTENTION!
This radio is restricted to occupational use only to
satisfy FCC RF energy exposure requirements.
Before using this product, read the RF energy awareness
information and operating instructions in the Product
Safety and RF Exposure booklet enclosed with your radio
(Motorola Publication part number 6881095C99) to
ensure compliance with RF energy exposure limits.
Important Safety Information
Product Safety and RF Exposure Compliance
Software Version
For a list of Motorola-approved antennas and other
accessories, visit the following website:
http://www.motorola.com/governmentandenterprise
ix
English
Computer Software Copyrights
Computer Software Copyrights
Documentation Copyrights
The Motorola products described in this manual may
include copyrighted Motorola computer programs stored
in semiconductor memories or other media. Laws in the
United States and other countries preserve for Motorola
certain exclusive rights for copyrighted computer
programs including, but not limited to, the exclusive right
to copy or reproduce in any form the copyrighted
computer program. Accordingly, any copyrighted
Motorola computer programs contained in the Motorola
products described in this manual may not be copied,
reproduced, modified, reverse-engineered, or distributed
in any manner without the express written permission of
Motorola. Furthermore, the purchase of Motorola
products shall not be deemed to grant either directly or by
implication, estoppel, or otherwise, any license under the
copyrights, patents or patent applications of Motorola,
except for the normal non-exclusive license to use that
arises by operation of law in the sale of a product.
No duplication or distribution of this document or any
portion thereof shall take place without the express
written permission of Motorola. No part of this manual
may be reproduced, distributed, or transmitted in any
form or by any means, electronic or mechanical, for any
purpose without the express written permission of
Motorola.
English
Disclaimer
The information in this document is carefully examined,
and is believed to be entirely reliable. However, no
responsibility is assumed for inaccuracies. Furthermore,
Motorola reserves the right to make changes to any
products herein to improve readability, function, or
design. Motorola does not assume any liability arising out
of the applications or use of any product or circuit
described herein; nor does it cover any license under its
patent rights, nor the rights of others.
Getting Started
How to Use This User Guide
This User Guide covers the basic operation of the APX™ 7500
Mobiles.
However, your dealer or system administrator may have
customized your radio for your specific needs. Check with your
dealer or system administrator for more information.
Throughout the text in this publication, you will notice the use of
WARNING, Caution, and Note. These notations are used to
emphasize that safety hazards exist, and the care that must be
taken or observed.The following special notations identify
certain items:
WARNING
Caution
Note:
An operational procedure, practice, or condition,
etc., which may result in injury or death if not
carefully observed.
Getting Started
Take a moment to review the following:
How to Use This User Guide . . . . . . . . . . . . . . . . . . . . . page 1
Notations Used in This Manual . . . . . . . . . . . . . . . . . . . page 1
What Your Dealer/System Administrator Can Tell You . page 2
Notations Used in This Manual
An operational procedure, practice, or
condition, etc., which may result in damage
to the equipment if not carefully observed.
An operational procedure, practice, or condition,
etc., which is essential to emphasize.
English
Example
Description
Home button Buttons and keys are shown in bold print or as
or H
an icon.
What Your Dealer/System Administrator
Can Tell You
You can consult your dealer or system administrator about the
following:
PHONE
Menu entries are shown similar to the way they
appear on the radio’s display.
• Is your radio preprogrammed with any preset conventional
This means “Press the right side of the 4-way
Navigation button.”
• Which buttons have been programmed to access other
channels?
features?
Getting Started
• What optional accessories may suit your needs?
English
Preparing Your Radio for Use
Press the Power On/Off Button
briefly to power on the radio.
After a short time, the red, yellow
and green LEDs light up. The
display then shows Zone and
channel text, and menu items
display on the screen.
Power On/
Off Button
The backlight will turn on to the last selected dim level.
Note:
Pressing the Power On/Off Button before the LED
lights up will be ignored.
If FAIL ##/## appears in the display, the radio will not
function until the condition has been corrected.
If ERROR ##/## appears, some non-critical data has
been changed. If either of these displays appear, if the
display goes blank, or if the unit appears to be locked
up, see Helpful Tips on page 99 for more information.
Preparing Your Radio for Use
Turning On the Radio . . . . . . . . . . . . . . . . . . . . . . . . . . page 3
Validating Compatibility During Power Up . . . . . . . . . page 4
Adjusting the Volume. . . . . . . . . . . . . . . . . . . . . . . . . . . page 4
Turning On the Radio
If CH MISMATCH appears, means that either the
Control Head has been connected to an incompatible
transceiver, or vice versa.
If your radio does not power up, contact your dealer.
To turn off the radio, press the Power On/Off Button after the
LEDs light up.
English
 Validating Compatibility During Power Up
The radio validates and updates the software and hardware of
your control head(s) during power up. Follow the procedure
below when your radio runs this task.
Procedure:
1 The display shows MAINTENANCE MODE REMOTE DEVICE;
Preparing Your Radio for Use
promptly followed by other maintenance statuses.
2 The display shows UPDATE DONE PLEASE RESET upon
completion.
OR
The display shows UPDATE FAILED PLEASE RESET when it
fails to update.
3 Press the Power On/Off Button to reset. The radio runs the
usual power up operation if the software updates are
complete.
OR
The radio runs the Maintenance Mode if the updates are not
complete and repeat step 1.
Note:
English
If SW INCOMPLETE appears, use Flashport Recovery
Tool to update the control heads before you power on
the radio again.
Adjusting the Volume
To increase the volume,
rotate the Volume Knob
clockwise to increase the
volume.
To decrease the volume,
rotate the Volume Knob
counterclockwise.
Volume Knob
Radio Parts and Controls
Identifying Radio Controls
 O5 Control Head and Microphone
16 Volume Knob
15 Dim Button
14 Home Button
13 Power On/Off Button
12 Indicators
11
10 Orange Button*
Push-to-Talk
9 (PTT) Button
Mode Knob
Navigation
Button
LED Indicators
Menu Entries
Menu Select Button*
Accessory Port (Microphone)
Accy No-Dot
Button (Purple)*
Identifying Radio Controls
Take a moment to review the following:
Radio Parts and Controls . . . . . . . . . . . . . . . . . . . . . . . page 5
O5 Control Head and Microphone . . . . . . . . . . . . . . . page 5
Programmable Features . . . . . . . . . . . . . . . . . . . . . . . . page 6
Assignable Radio Functions . . . . . . . . . . . . . . . . . . . page 6
Assignable Settings or Utility Functions. . . . . . . . . . . page 8
Accessing the Preprogrammed Functions. . . . . . . . . . . page 9
Using the Menu Select Buttons . . . . . . . . . . . . . . . . . page 9
Using the Advance Programmable Buttons . . . . . . . . page 9
Using the Navigation Buttons. . . . . . . . . . . . . . . . . . page 10
Using the Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 11
Keypad Characters – Uppercase Mode. . . . . . . . . . page 11
Keypad Characters – Lowercase Mode. . . . . . . . . . page 12
Keypad Characters – Numeric Mode. . . . . . . . . . . . page 13
Keypad Characters – Hexadecimal Mode . . . . . . . . page 14
Push-To-Talk (PTT) Button . . . . . . . . . . . . . . . . . . . . . page 15
Accy 1-Dot
Button*
Accy 2-Dot
Button*
*These controls/buttons are programmable.
English
Programmable Features
Navigation
Button
22 (Microphone)
Data Feature
17
Button*
Button
21 Cancel
(2)
Home Button
(Microphone) 18
20 Okay/Select
Identifying Radio Controls
Keypad
Buttons
Button (3)
19
Any references in this manual to a control that is
“preprogrammed” means that the control must be programmed
by a dealer or a qualified radio technician using the radio’s
programming software, in order to assign a feature to that
control.
The programmable buttons can be programmed as shortcuts to
radio functions or preset channels/groups depending on the
duration of a button press:
• Press – Pressing and releasing rapidly.
• Long press – Pressing and holding for the programmed
*This button is programmable.
Note:
English
The microphone is not part of a radio. It is an optional
accessory.
duration (between 0.25 seconds and 3.75 seconds).
• Hold down – Keeping the button pressed.
 Assignable Radio Functions
Call Alert – Allows the radio to function like a pager, or to verify
if a radio is active on the system.
Call Response – Allows you to answer a private call or phone
call.
Channel – Selects a channel.
Contacts – Selects the Contacts menu.
One Touch 1 – 4 – Launches a specific feature with one single
button-press. You can setup as much as four separately
programmed buttons for four different features.
Emergency – Depending on the programming, initiates or
cancels an emergency alarm or call.
Phone – Allows you to make and receive calls similar to
standard phone calls.
Information – Displays the basic radio information, IP-related
information, and buttons or switches control mapping.
Private Call (Trunking Only) – Allows a call from an individual
radio to another individual radio.
Intercom – Enables users of multiple control heads to talk to
each other via the control heads in a multi-control head setup.
Radio Profiles – Allows for easy access to a set of
preprogrammed visual and audio settings of the radio.
Internet Protocol Address – Displays the Internet Protocol (IP)
address, device name, and status of the radio.
Recent Calls – Allows for easy access to the list of calls
recently received or made.
Location – Determines the current location (latitude, longitude,
time and date), and also the distance and bearing to another
location. Or, turns the GPS functionality on or off for all
locations.
Rekey Request – Notifies the dispatcher that you want new
encryption keys.
Message – Enters the current message list.
Monitor (Conventional Only) – Monitors a selected channel
for all radio traffic until function is disabled.
Multiple Private Line (Conventional Only) – Selects the
Multiple Private Line lists.
Nuisance Delete – Temporarily removes an unwanted channel,
except for priority channels or the designated transmit channel,
from the scan list.
Repeater Access Button (RAB) (Conventional Only) –
Allows to manually send a repeater access codeword.
Identifying Radio Controls
Dynamic Priority (Conventional Only) – Allows any channel
in a scan list (except for the Priority-One channel) to temporarily
replace the Priority-Two channel.
Reprogram Request (Trunking Only) – Notifies the dispatcher
that you want a new dynamic regrouping assignment.
Request-To-Talk (Conventional Only) – Notifies the
dispatcher that you want to send a voice call.
Scan – Toggles scan on or off.
Secure/Clear – Toggles secure transmission on or off.
Selective Call (Conventional Only) – Calls an assigned radio.
English
Site Display (Trunking Only) – Views the current site or
enable a site search for SmartZone operation.
Site Lock/Unlock (Trunking Only) – Toggles between lock and
unlock mode when using the SmartZone option.
Identifying Radio Controls
Status – Sends data calls to the dispatcher about a predefined
status.
 Assignable Settings or Utility Functions
Dim – Changes the display brightness.
Front/Rear – Switches one of two control heads to be active at
one time.
Horns/Lights – Toggles horns and lights feature on or off.
Talkaround/Direct (Conventional Only) – Toggles between
using a repeater and communicating directly with another radio.
Low Power – Toggles transmit power level between high and
low.
Talkgroup (Conventional Only) – Allows a call from an
individual radio to a group of radios.
Voice Announcement – Audibly indicates the current feature
mode, Zone or Channel the user has just assigned.
Text Messaging Service (TMS) – Selects the text messaging
menu.
Voice Mute – Toggles voice mute on or off for the channels
which have enabled In-Call User Alert. When Voice Mute is
active, the radio remains muted to all conventional dispatch
calls and affiliated trunking group calls.
TMS Quick Text – Selects a predefined message.
User – Automatically registers with the server.
Zone Down – Toggles downward through the zones in the
radio.
Zone Select – Allows selection from a list of zones.
Zone Up – Toggles upward through the zones in the radio.
English
Accessing the Preprogrammed Functions
This feature is to help you to shorten the process of applying
certain common features.
Orange Button*
• A short or long press of the relevant programmable buttons.
OR
• Use the Menu Select Button (g).
 Using the Menu Select Buttons
The Menu Select Buttons allow to access the menu entries of
features.
Menu Select Button*
Check with your dealer or system administrator for the
list of features activated in your radio.
Accy No-Dot Button
(Purple)*
Your radio may be preprogrammed differently from the following
example, but the steps for selecting a channel may appear as
shown below:
Accy 1-Dot Button*
Note:
Identifying Radio Controls
You can access various radio functions through one of the
following ways:
 Using the Advance Programmable Buttons
Accy 2-Dot Button*
• Press the Menu Select button (g) directly below CHAN.
* These programmable buttons support the One Touch Button feature.
(Quick Access) One Touch Button – Enters a menu with a
short press on the preprogrammed One Touch button. Features
assigned to these buttons are Call, Call Alert, Phone, Repeater
Access, MDC RTT Button Access, Status and Message.
Menu Select Button
English
 Using the Navigation Buttons
 Home Button
The H button returns you to the home (default) display. In most
cases, this is the current mode.
Identifying Radio Controls
For selected radio features, the H button is also used to save
user-edited radio settings or information before returning you to
the Home screen.
Note:
Some features do not require you to press H to go to
the Home screen. Refer to the individual feature
sections in this manual for further details on saving
user-edited radio settings or information.
The H button also can revert to home channel. Check with
your dealer or system administrator for more information.
 Data Feature Button
Use this button to access data-related features, such as the
Text Messaging Service (TMS) feature screen.
10
English
 4-Way Navigation Button
Use this button to scroll up, down, left or right.
Press and release one of the button to scroll from one entry to
the next one. Press and hold one of the button to have the radio
toggles through the list automatically (release the button to
stop).
 Volume Knob
Use this Volume Knob to adjust the volume of the speakers by
turning it clockwise or counterclockwise.
 Mode Knob
Use this Mode Knob to scroll through the channels by turning it
clockwise or counterclockwise.
Using the Keypad
 Keypad Characters – Uppercase Mode
Number of Times Key is Pressed
Key
10
11
12
13
14
15
16
17
18
19
20
21
“
‘
4 G
6 M
9 W
Identifying Radio Controls
You can use the 3 x 4 alphanumeric keypad on the keypad microphone (see Microphones on page 103) to access your radio’s
features. The keypad functions in a manner similar to a standard telephone keypad when entering numeric digits. When the keypad is
used to edit a list, each key can generate different characters of the alphabet. The tables below show the number of times a key needs
to be pressed to generate the required character.
0 Toggle between mixed case mode, uppercase mode, and lowercase mode.
* Space
# Toggle between numeric and letter mode.
11
English
 Keypad Characters – Lowercase Mode
Identifying Radio Controls
Number of Times Key is Pressed
Key
10
11
12
13
14
15
16
17
18
19
20
21
“
‘
6 m
0 Toggle between mixed case mode, uppercase mode, and lowercase mode.
* Space
# Toggle between numeric and letter mode.
12
English
 Keypad Characters – Numeric Mode
Key
10
11
12
13
14
15
16
17
18
19
20
21
“
‘
Identifying Radio Controls
Number of Times Key is Pressed
* Space
# Toggle between numeric and letter mode.
13
English
 Keypad Characters – Hexadecimal Mode
Identifying Radio Controls
Number of Times Key is Pressed
Key
* Not applicable
# Not applicable
14
English
10
11
12
13
14
15
16
17
18
19
20
21
Push-To-Talk (PTT) Button
PTT
Button
• While a call is in progress, the
PTT button allows the radio to
transmit to other radios in the
call.
Press and hold down PTT
button to talk. Release the PTT
button to listen.
The microphone is activated
when the PTT button is pressed.
• While a call is not in progress, the PTT button is used to make
a new call. See Making a Radio Call on page 29 for more
information.
Identifying Status Indicators
Your radio indicates its operational status through the following:
Status Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 16
Text Messaging Service (TMS) Icons. . . . . . . . . . . . . . page 18
Status Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 18
TMS Menu Options. . . . . . . . . . . . . . . . . . . . . . . . . . page 19
LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 20
Intelligent Lighting Indicators . . . . . . . . . . . . . . . . . . . . page 21
Alert Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 22
Identifying Status Indicators
The PTT button on the side of the
microphone serves two basic
purposes:
15
English
Status Icons
The liquid crystal display (LCD) of your radio shows the radio
status, text entries, and menu entries.
Identifying Status Indicators
The following are the icons that appear on the radio’s display.
Receiving
Radio is receiving a call or data.
Transmitting
Radio is transmitting a call or data.
16
English
Direct
• On = Radio is currently configured for direct
radio-to-radio communication (during
conventional operation only).
• Off = Radio is connected with other radios
through a repeater.
Monitor (Carrier Squelch)
Selected channel is being monitored (during
conventional operation only).
In-Call User Alert
Call Received
Radio has received an Individual Call.
Received Signal Strength Indicator (RSSI)
The number of bars displayed represents the
received signal strength for the current site, for
trunking only. The more stripes in the icon, the
stronger the signal.
• On = The feature is enabled. Voice muting of
the affiliated trunking talkgroup or selected
conventional channel is activated.
• Off = The feature is disabled. Voice muting of
the affiliated trunking talkgroup or selected
conventional channel is deactivated.
H .
or
Power Level
• L = Radio is set at Low power.
• H = Radio is set at High power.
Scan
Radio is scanning a scan list.
• Blinking dot = Radio detects activity on
channel designated as
Priority-One.
Location Signal
• Blinking = Location feature is enabled, but no
designated as Priority-Two.
• On steady = View mode
• Blinking = Program mode
location signal is available.
User Login Indicator (IP Packet Data)
• Off = Clear operation.
• Blinking = Receiving an encrypted voice call.
AES Secure Operation
• On = AES Secure operation.
radio.
radio.
• Blinking = Device registration or user
registration with the server failed due to an
invalid username or pin.
Secure Operation
• On = User is currently associated with the
• Off = User is currently not associated with the
Vote Scan Enabled
The vote scan feature is enabled.
• On = Secure operation.
signal is available.
• Off = Location feature is disabled.
• Steady dot = Radio detects activity on channel
View/Program Mode
Radio is in the view or program mode.
• On = Location feature is enabled, and location
Data Activity
Data activity is present.
Identifying Status Indicators
Priority Channel Scan
Hexadecimal
Indicates that the text entry is currently in
hexadecimal mode.
• Off = Clear operation.
• Blinking = Receiving an encrypted voice call.
17
English
Text Messaging Service (TMS) Icons
This feature allows you to send and receive text messages. See
Text Messaging Service (TMS) on page 62 for more
information.
3/6
Identifying Status Indicators
 Status Icons
The following icons appear on the radio’s display for TMS
features:
Inbox Full
The Inbox is full.
Message Sent
The text message is sent successfully.
Message Unsent
The text message cannot be sent.
Unread Message
18
English
Read Message
The selected text message in the Inbox has been
read.
Message Index
Indicates the index of the current message the
user is viewing.
Example: If the user is looking at the third
message out of a total of 6 messages in the
Inbox folder, the icon is displayed as the icon on
the left column.
Priority Status
• The “Priority” feature is toggled on before the
message is sent.
• Messages in the Inbox folder are flagged with
“Priority”.
• User receives a new message.
• The selected text message in the Inbox has
not been read.
Request Reply
• The “Request Reply” feature is toggled on
before the message is sent.
• Messages in the Inbox folder are flagged with
“Request Reply”.
Priority Status and Request Reply
• User is composing a message with a priority
Menu Option
status and a request for a reply.
• Messages in the Inbox folder are flagged with
”Priority” and “Request Reply”.
Description/Function
INBX
Brings you to your incoming messages
screen.
COMP
Brings you to the compose screen.
Numeric
Indicates that the text entry is currently in
numeric mode.
DRFT
Brings you to the saved message screen.
SENT
Brings you to the sent messages screen.
Mixed Case
Indicates that the text entry is currently in normal
text mode.
BACK
Brings you back to the previous menu
screen.
EDIT
Edits a draft message or key in a target
address.
SAVE
Saves the messages you have edited to the
Draft folder.
RPLY
Replies to a message.
Uppercase
Indicates that the text entry is currently in
uppercase mode.
Lowercase
Indicates that the text entry is currently in
lowercase mode.
DEL
Deletes a message or a character text during
editing mode.
NEW
Creates a new message.
LIST
Brings you to the predefined messages
screen.
IMPT
Toggles the “Priority Status” icon on or off for
an outgoing message.
RQRP
Toggles “Request Reply” icon on or off for an
outgoing message.
Identifying Status Indicators
 TMS Menu Options
19
English
Menu Option
Identifying Status Indicators
CURR
Description/Function
Deletes the current selected message.
LED Indicator
LED indicator shows the operational status of your radio.
ALL
Selects to delete all the messages in the
current folder.
YES
Deletes all the messages in the current
folder.
Yellow LED
NO
Cancel the delete all messages options.
Green LED
EXIT
Exits to the Home screen.
OPTN
Brings you to the Options main screen.
SEL
SEND
Red LED
Selects a predefined message or address.
Sends the message.
Solid red – Radio is transmitting.
Rapidly blinking red – Radio has failed the self test upon
powering up or encountered a fatal error.
Solid yellow – Channel is busy.
Blinking yellow – Radio is receiving a secured transmission.
Solid green – Radio is powering up, or is on a non-priority
channel while in the Scan List Programming mode.
Blinking green – Radio is receiving an individual or telephone
call, or is on a Priority-Two channel while in the Scan List
Programming mode.
Rapidly blinking green – Radio is on a Priority-One channel
while in the Scan List Programming mode.
20
English
Intelligent Lighting Indicators
Note:
This feature must be preprogrammed by a qualified radio technician.
Backlight
Event
Orange
Emergency Alerts
Red
Critical Alerts
When
The radio initiates an emergency alarm or call.
The radio receives an emergency alarm or call.
The radio is out of range.
The radio enters failsoft mode.
The radio is unable to establish a full connection with the system.
The radio receives a private call.
Green
Call Alerts
The radio receives a phone call.
The radio receives a call alert.
The radio receives a selective call.
Identifying Status Indicators
This feature temporary changes the radio’s display backlight color and the alert text background color to help signal that a radio event
has occurred.
21
English
Alert Tones
An alert tone is a sound or group of sounds. Your radio uses alert tones to inform you of your radio’s conditions. The following table
lists these tones and when they occur.
You Hear
Tone Name
Radio Self Test Fail
Identifying Status Indicators
Reject
22
English
Short,
Low-Pitched
Tone
Time-Out Timer Warning
No ACK Received
Individual Call
Warning Tone
Long,
Low-Pitched
Tone
A Group of
Low-Pitched
Tones
Time-Out Timer
Timed Out
Talk Prohibit/PTT Inhibit
Heard
When radio fails its power-up self test.
When an unauthorized request is made.
Four seconds before time out.
When radio fails to receive an acknowledgment.
When radio is in an individual call for greater than 6 seconds without any activity.
When the Time-Out Timer has expired.
(When PTT button is pressed) transmissions are not allowed.
Out of Range
(When PTT button is pressed) the radio is out of range of the system.
Invalid Mode
When radio is on an unpreprogrammed channel.
Busy
When system is busy.
You Hear
Tone Name
Radio Self Test Pass
Short,
Medium-Pitched
Tone
Clear Voice
Priority Channel
Received
Emergency Alarm Entry
Central Echo
Long,
Medium-Pitched
Tone
Volume Set
Emergency Exit
Failsoft
Automatic Call Back
Talk Permit
A Group of
Medium-Pitched
Tones
Keyfail
Console Acknowledge
Received Individual Call
When correct key is pressed.
When radio passes its power-up self test.
At beginning of a non-coded communication.
When activity on a priority channel is received.
When entering the emergency state.
When central controller has received a request from a radio.
When volume is changed on a quiet channel.
When exiting the emergency state.
When the trunking system fails.
When voice channel is available from previous request.
(When PTT button is pressed) verifying system accepting transmissions.
When encryption key has been lost.
Identifying Status Indicators
Valid Key-Press
Heard
When status, emergency alarm, or reprogram request ACK is received.
When Call Alert or Private Call is received.
Call Alert Sent
When Call Alert is received by the target radio.
Site Trunking
When a SmartZone trunking system fails.
23
English
You Hear
Tone Name
Fast Ringing
Identifying Status Indicators
Ringing
Heard
When system is searching for target of Private Call.
Enhanced Call Sent
When waiting for target of Private Call to answer the call.
Phone Call Received
When a land-to-mobile phone call is received.
Gurgle
Dynamic Regrouping
(When the PTT button is pressed) a dynamic ID has been received.
Unique,
Low-Pitched
Chirp
New Message
When a new message is received.
Unique,
High-Pitched
Chirp
Priority Status
When a priority message is received.
24
English
General Radio Operation
Use this navigation guide to familiarize yourself with the basic
Call features:
Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 25
Selecting a Radio Channel . . . . . . . . . . . . . . . . . . . . . page 26
Receiving and Responding to a Radio Call . . . . . . . . . page 26
Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . . . page 29
Repeater or Direct Operation . . . . . . . . . . . . . . . . . . . page 32
Monitoring Features. . . . . . . . . . . . . . . . . . . . . . . . . . . page 32
A zone is a group of channels.
Note:
Your radio must be preprogrammed to allow you to use
these features.
Procedure:
1 > or < to ZONE.
2 Press the Menu Select button directly below ZONE. The
display shows the current zone and channel.
3 > or < button until the desired zone is displayed.
4 Press H or the PTT button to confirm the selected zone
number.
5 Press the PTT button to begin transmitting on the displayed
General Radio Operation
Once you understand how your APX 7500 O5 CH Mobile is
configured, you are ready to use your radio.
Selecting a Zone
zone channel.
25
English
Selecting a Radio Channel
A channel is a group of radio characteristics, such as transmit/
receive frequency pairs.
Use the following procedure to select a channel.
General Radio Operation
Note:
Your radio must be preprogrammed to allow you to use
this feature. If you select a channel that is not within
the preprogrammed band, the radio indicates that it is
on an unsupported frequency with both audio and
visual warnings.
Once you have selected the required channel and/or zone, you
can proceed to receive and respond to calls.
Red LED
Yellow LED
Green LED
Consult a qualified radio technician for the right choice
between the following methods.
Procedure:
Rotate the Mode knob until the display shows the desired
channel.
OR
1 Press and hold > to scroll to CHAN and press the Menu
Select button directly below CHAN. The display shows the
current zone and channel.
2 Rotate the Mode knob to the desired channel.
3 Press H or the PTT button to confirm the channel.
4 Press the PTT button to transmit on the displayed zone
26
Receiving and Responding to a Radio Call
channel.
English
You see solid red while the radio is transmitting, and solid
yellow when the radio is receiving a transmission (conventional
mode only). There is no LED indication when the radio receives
a transmission in trunking mode.
If the radio is receiving a secure transmission, the LED blinks
yellow.
 Receiving and Responding to a Talkgroup Call
Procedure:
When you receive a talkgroup call (while on the Home screen),
depending on how your radio is preprogrammed:
1 ASTRO Conventional Only:
The LED lights up solid yellow. The display shows the
talkgroup alias or ID, and the caller alias or ID.
OR
Trunking Only:
The display shows the caller alias or ID.
2 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm)
from your mouth.
3 Press the PTT button to respond to the call. The LED lights
up solid red.
(Trunking Only)
A Private Call is a call from an individual radio to another
individual radio.
These one-to-one calls between two radios are not heard by
others in the current talkgroup. The calling radio automatically
verifies that the receiving radio is active on the system and can
display the caller ID.
Note:
If the feature inactivity timer is enabled, your radio
automatically exits the feature when your radio is left
idle long enough for the time to expire. You will hear
the Menu Inactive Exit Tone upon feature exit.
Procedure:
When you receive a Private Call:
1 You hear two alert tones and the LED blinks green. The
General Radio Operation
To receive a call from a group of users, your radio must be
configured as part of that talkgroup.
 Receiving and Responding to a Private Call
display shows CALL RECEIVED and the caller alias or ID.
4 Release the PTT button to listen.
2 Press the Menu Select button directly below RESP within 20
See Making a Talkgroup Call on page 29 for details on making
a Talkgroup Call.
3 During the call, the display shows the caller alias (name), if it
seconds after the call indicators begin.
is in the call list.
OR
During the call, the display shows the caller ID (number), if
the caller’s name is not in the call list.
27
English
4 Press and hold the PTT button to talk. Release the PTT
General Radio Operation
button to listen.
 Receiving and Responding to a Telephone Call
5 Press H to hang up and return to the Home screen.
This feature allows you to receive calls similar to standard
phone calls from a landline phone.
Note:
If you press PTT button before pressing the Menu
Select button directly below RESP, your conversation
will be heard by all members of the talk group.
Note:
If 20 seconds pass before you press the Menu Select
button directly below the RESP, you will not respond
privately to the call just received. Instead, you initiate a
Private Call.
Procedure:
See Making a Private Call (Trunking Only) on page 30 for
details on making a Private Call.
28
English
If the feature inactivity timer is enabled, your radio
automatically exits the feature when your radio is left
idle long enough for the time to expire. You will hear
the Menu Inactive Exit Tone upon feature exit.
1 You hear a telephone-type ringing and the LED blinks green.
The backlight of the screen turns green. The display shows
PHONE CALL and the call received icon blinks.
2 Press the Menu Select button directly below RESP.
3 Press and hold the PTT button to talk. Release the PTT
button to listen.
4 Press H or the Menu Select button directly below EXIT to
hang up and return to the Home screen.
See Making a Telephone Call on page 31 for details.
Making a Radio Call
2 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm)
from your mouth.
• The preprogrammed Zone menu
• The Mode Knob
• A preprogrammed One Touch button
• The Contacts list (see Contacts on page 42).
Note:
If the feature inactivity timer is enabled, your radio
automatically exits the feature when your radio is left
idle long enough for the time to expire. You will hear
the Menu Inactive Exit Tone upon feature exit.
 Making a Talkgroup Call
3 Press the PTT button to make the call.
4 ASTRO Conventional Only:
The LED lights up solid red. The display shows the
talkgroup alias or ID.
OR
Trunking Only:
The LED lights up solid red.
5 Speak clearly into the microphone.
6 Release the PTT button to listen.
General Radio Operation
You can select a zone, channel, subscriber ID, or talkgroup by
using:
To make a call to a group of users, your radio must be
configured as part of that talkgroup.
Procedure:
1 > or < to TGRP and press the Menu Select button directly
belowTGRP.
The display shows the last-selected talkgroup.
Press the Menu Select button directly below SEL.
OR
Rotate the Mode Knob to select the channel with the
desired talkgroup.
29
English
 Making a Private Call (Trunking Only)
5 A telephone-type ringing sounds if the receiving unit is in
This feature allows you to send an individual Call Alert or page if
there is no answer from the target radio. Your radio must be
preprogrammed to allow you to use this feature.
6 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm)
General Radio Operation
Procedure:
Press the preprogrammed Quick Access (One-Touch)
Enhanced Private Call button to dial the preprogrammed ID
and proceed to Step 5.
OR
Follow the procedure below.
1 > or < to CALL.
2 Press the Menu Select button directly below CALL. The
display shows the last transmitted or received.
3 Press the Menu Select button directly below CNTS to scroll
through and select the required ID.
OR
Press the Menu Select button directly below LIST to go to
the first number of the call list.
OR
> or < to the required ID.
OR
Use the keypad to enter the required ID.
4 Press the PTT button to start the Private Call.
30
English
service. The display shows CALLING... or
CALLING....
from your mouth.
7 When you are connected, the display shows the ID of the
target radio. Press and hold the PTT button to talk. Release
the PTT button to listen.
OR
If no acknowledgment is received, the display shows NO
ACKNOWLEDGE.
OR
If the target radio does not respond before the time out, the
display shows NO ANSWER.
8 Press H to return to the Home screen.
See Sending a Call Alert Page on page 55 for more
information.
6 When your call is answered, press the PTT button to talk.
This feature allows you to make calls similar to standard phone
calls to a mobile or landline phone.
7 Release the PTT button to listen.
Procedure:
Press the preprogrammed Quick Access (One-Touch) Phone
Call button to dial the preprogrammed phone number and
proceed to Step 5.
OR
Follow the procedure below.
1 > or < to PHON.
2 Press the Menu Select button directly below PHON. The
display shows the last transmitted phone number.
3 Press the Menu Select button directly below CNTS to scroll
through and select the required ID.
OR
Press the Menu Select button directly below LIST to go to
the first number of the call list.
OR
8 Press H to return to the Home screen.
See Alert Tones on page 22 for more information if your call is
NOT answered.
General Radio Operation
 Making a Telephone Call
> or < to the required phone number.
OR
Use the keypad to enter the required phone number.
4 Press and release the PTT button to dial the phone number.
5 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm)
from your mouth.
31
English
Repeater or Direct Operation
The REPEATER operation increases the radio’s range by
connecting with other radios through a repeater. The transmit
and receive frequencies are different.
General Radio Operation
The DIRECT or “talkaround operation” allows you to bypass the
repeater and connect directly to another radio. The transmit and
receive frequencies are the same.
Procedure:
Press the preprogrammed Repeater/Direct switch to toggle
between talkaround and repeater modes.
OR
Follow the procedure below.
Monitoring Features
Radio users who switch from analog to digital radios often
assume that the lack of static on a digital channel is an
indication that the radio is not working properly. This is not the
case.
Digital technology quiets the transmission by removing the
“noise” from the signal and allowing only the clear voice or data
information to be heard.
Monitor a channel to ensure the channel is clear before
transmitting.
 Monitoring a Channel
1 > or < to DIR.
Procedure:
2 Press the Menu Select button directly below DIR.
Lift the microphone off hook.
3 The display shows REPEATER MODE if the radio is currently
Conventional Modes Only:
in Repeater mode.
OR
The display shows DIRECT MODE and the Talkaround icon if
the radio is currently in Direct mode (during conventional
operation only).
You can repeat step 2 to toggle between the two modes. Once
in Direct Mode, press PTT button to start conversation with the
radios nearby.
32
English
1 Listen for activity on that channel.
2 Adjust the Volume knob if necessary.
3 If you hear no activity, press and hold the PTT button to start
your conversation.
OR
Trunked Modes Only:
1 Press the PTT button.
tone and the t indicator lights steadily, then proceed with
your message.
3 Release the PTT button to receive (listen).
if you are not in the range of the system, you may hear a
continuous low-pitched tone and the display shows OUT OF
RANGE.
This feature allows you to monitor channel traffic on
conventional channels by defeating the coded squelch. Thus
you can to listen to another user active on the channel. This
way, you may be prevented from talking over someone else’s
conversation.
Note:
This feature must first be enabled by a qualified radio
technician or system administrator.
Procedure:
Take the control head off hook. (This is the same as monitor on.
You hear all channel traffic.)
OR
1 At Home mode where the default zone and channel are
being displayed, > or < button to MON.
General Radio Operation
2 If you hear two, short, high-pitched tones, or if you hear no
 Conventional Mode Operation
2 Press the Menu Select button directly below MON
momentarily to activate monitoring. The display shows
MONITOR ON.
3 Press the Menu Select button to deactivate the monitoring.
The display shows MONITOR OFF.
MONITOR ON shown on the display indicates that the radio is
monitoring. Pressing the Menu Select button again turns
monitor off and you don’t hear all channel traffic.
If you try to transmit on a receive-only channel, you hear an
invalid tone until you release the PTT button.
33
English
Advanced Features
Advanced Features
Use this navigation guide to learn more about advanced
features available with your radio:
Advanced Call Features . . . . . . . . . . . . . . . . . . . . . . . page 34
Multiple Control Head Features . . . . . . . . . . . . . . . . . page 39
Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 42
Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 48
Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 50
Call Alert Paging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 53
Emergency Operation . . . . . . . . . . . . . . . . . . . . . . . . . page 56
Automatic Registration Service (ARS) . . . . . . . . . . . . page 59
Text Messaging Service (TMS) . . . . . . . . . . . . . . . . . . page 62
Secure Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . page 72
The Global Positioning System (GPS) . . . . . . . . . . . . page 76
Trunking System Controls. . . . . . . . . . . . . . . . . . . . . . page 84
Utilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 88
34
English
Advanced Call Features
 Calling a Phone Not in the List
1 > or < to PHON.
2 Press the Menu Select button directly below PHON.
3 Enter the desired phone number from the optional keypad
microphone. The display updates as the numbers are
entered.
4 Press 3 button on the keypad microphone to make the call.
5 Press and hold the PTT button to talk. Release the PTT
button to listen.
6 Press H or Menu Select button directly below PHON to exit.
 Receiving and Making a Selective Call
(Conventional Only)
 Receiving a Selective Call
Procedure:
1 When you receive a Selective Call, you hear two alert tones
and the LED lights up solid yellow. The call received icons
blink and the display alternates between CALL RECEIVED
and the home display.
2 The speaker unmutes.
3 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm)
from your mouth.
4 Press and hold the PTT button to talk. Release the PTT
button to listen.
Note:
If you press PTT button before pressing the Menu
Select button directly below CALL, your conversation
will be heard by all members of the talk group.
 Making a Selective Call
Procedure:
Press the preprogrammed Quick Access (One-Touch)
Selective Call button to dial the preprogrammed ID and
proceed to Step 4.
OR
Follow the procedure below.
1 > or < to CALL.
Advanced Features
This feature allows you to receive a call from or to call a specific
individual. It is intended to provide privacy and to eliminate the
annoyance of having to listen to conversations that are of no
interest to you.
If 20 seconds pass before you press the Menu Select button
directly below the CALL, you will not respond privately to the call
just received. Instead, you initiate a Selective Call. See Making
a Selective Call on page 35.
2 Press the Menu Select button directly below CALL. The
display shows the last transmitted or received ID.
3 Press the Menu Select button directly below CNTS to scroll
through and select the required ID.
OR
Press the Menu Select button directly below LIST to go to
the last number dialed.
OR
> or < to the required ID.
OR
Use the keypad to enter the required ID.
35
English
4 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm)
from your mouth.
5 Press and hold the PTT button to start the Selective Call.
The display shows the ID of the target radio.
6 Release the PTT button to listen.
7 Press H to return to the Home screen.
If you do not press H button to hang up, your radio will remain
in Selective Call state with the other unit. You will miss all
subfleet traffic and incoming phone calls.
 Using the Talkgroup Call Feature (Conventional
Advanced Features
Operation Only)
This feature allows you to define a group of conventional
system users so that they can share the use of a conventional
channel.
Note:
Encryption keys are associated to talkgroups. When
talkgroups are enabled, encryption keys are changed
by changing the active talkgroup. See Secure
Operations on page 72 for more information.
 Selecting a Talkgroup
Procedure:
1 > or < to TGRP.
36
English
2 Press the Menu Select button directly below TGRP. The
display shows the last talkgroup that was selected and
stored.
3 > or < to PSET for the preset preprogrammed talkgroup.
OR
> or < to the required talkgroup.
OR
Use the keypad to enter the number of the corresponding
talkgroup in the list.
4 Press the Menu Select button directly below SEL to save
the currently selected talkgroup and return to the Home
screen.
5 If the encryption key associated to the new talkgroup is
erased, a momentary key fail tone sounds and the display
shows KEY FAIL.
OR
If the encryption key that is associated to the new talkgroup
is not allowed, a momentary key fail tone sounds and the
display shows ILLEGAL KEY.
6 Press H or the PTT button to exit.
 Sending a Status Call
5 Press the PTT button to send the status. The display shows
This feature allows you to send data calls to the dispatcher
about a predefined status.
6 When the dispatcher acknowledges, four tones sound and
Note:
If the feature inactivity timer is enabled, your radio
automatically exits the feature when your radio is left
idle long enough for the time to expire. You will hear
the Menu Inactive Exit Tone upon feature exit.
Procedure:
Press the preprogrammed Status button and proceed to Step
3.
OR
Follow the procedure below.
1 > or < to STS.
2 Press the Menu Select button directly below STS.
3 The display shows the last acknowledged status call, or the
first status in the list.
4 > or < to the required status.
OR
Use the keypad to enter a number corresponding to the
location in the status list.
the display shows ACK RECEIVED. The radio returns to
normal dispatch operation.
OR
If no acknowledgment is received, a low-pitched tone
sounds and the display shows NO ACKNOWLEDGE.
7 Press H to return to the Home screen.
No traffic is heard on trunked channels while Status Calls is
selected. If the radio detects no Status Call activity for six
seconds, an alert tone sounds until you press H or the PTT
button.
Advanced Features
Each status can have up to a 14-character name. A maximum
of eight status conditions is possible.
PLEASE WAIT.
 Using the Dynamic Regrouping Feature (Trunking
Only)
This feature allows the dispatcher to temporarily reassign
selected radios to a single special channel so they can
communicate with each other. This feature is typically used
during special operations and is enabled by a qualified radio
technician.
You will not notice whether your radio has this feature enabled
until a dynamic regrouping command is sent by the dispatcher.
37
English
Note:
If you try to access a zone or channel that has been
reserved by the dispatcher as a dynamically regrouped
mode for other users, an invalid tone sounds.
Procedure:
1 When your radio is dynamically regrouped, it automatically
switches to the dynamically regrouped channel. A “gurgle”
tone sounds and the display shows the dynamically
regrouped channel’s name.
2 Press the PTT button to talk. Release PTT button to listen.
Advanced Features
When the dispatcher cancels dynamic regrouping, the radio
automatically returns to the zone and channel that you were
using before the radio was dynamically regrouped.
 Requesting a Reprogram
This feature lets you notify the dispatcher that you want a new
dynamic regrouping assignment.
Procedure:
Press the preprogrammed Reprogram Request button to send
reprogram request to the dispatcher and proceed to Step 3.
OR
Follow the procedure below.
1 > or < to RPGM.
2 Press the Menu Select button directly below RPGM to send
38
reprogram request to the dispatcher.
English
3 The display shows REPROGRAM RQST and PLEASE WAIT.
4 If you hear five beeps, the dispatcher has acknowledged the
reprogram request. The display shows ACK RECEIVED and
the radio returns to the Home screen.
OR
If the dispatcher does not acknowledge the reprogram
request within six seconds, a low-pitched alert tone sounds
and the display shows NO ACKNOWLEDGE.
Try again or press H to cancel and return to the Home
screen.
 Classifying Regrouped Radios
The dispatcher can classify regrouped radios into either of two
categories: Select Enabled or Select Disabled.
• Select-enabled radios are free to change to any available
channel, including the dynamic-regrouping channel, once the
user has selected the dynamic-regrouping position.
• Select-disabled radios cannot change channels while
dynamically regrouped. The dispatcher has forced the radio
to remain on the dynamic-regrouping channel.
The Scan or Private Call feature cannot be selected while your
radio is Select Disabled.
Multiple Control Head Features
This feature allows a transceiver to control as many as four O5
control heads. You can use the CAN cables to connect in any
configuration that does not exceed 131 feet (40 meters) in
combined length. Refer the O5 Control Head Installation
Manual (HLN6947) for further information.
The Multiple Control Head (MCH) feature consists of 2 modes
that can be programmed via Customer Programming Software
(CPS):
• All Active mode
• One Active mode
Note:
If two or more control heads are connected to the
system before enabling the MCH feature in the CPS,
the radio will display EXTRA CH or CH ID # ERR. Both
errors are FATAL.
This feature allows you to setup the control head in the Front
Panel Programming (FPP) mode. During the setup, the control
heads are defined as Control Head Number 1, Control Head
Number 2, Control Head Number 3 and Control Head Number
4.
Procedure:
1 Press the Power button to power off the radio.
2 Press and hold the left-most Menu Select button and the
emergency button simultaneously.
3 While continuing to depress these two buttons, press the
Power button to power on the radio and the control head.
Advanced Features
 Multiple Control Head Features
 Setting the Initial Control Head’s ID
4 The radio and the control head will power on into FPP
mode. The display shows control head’s ID number.
5 Turn the Mode knob to change the control head’s ID
number.
6 Press the Power button to power off the radio and exit FPP
mode.
7 Repeat steps 1 to 5 above to set the ID number for the rest
of the attached control heads.
39
English
 All Active Mode
The All Active mode enables all connected control heads
attached to the radio to operate concurrently with each other.
When you activate a feature on one control head, the rest of the
control heads will have the same activated features and
indicators on their respective display.
Advanced Features
Note:
The multiple control head feature allows only control
heads of the same type to be connected. Upon power
up, if a control head of a different type is connected to
the radio, the radio reports the FATAL error CH
MISMATCH on the display of all attached control
heads.
 Intercom Feature in All Active Mode
The intercom feature allows one control head user to talk to
another control head user in a Multiple Control Head
configuration. At any given time, when a control head being
operated has priority for the intercom call, all other control
heads are blocked until the active control head releases PTT
button.
This can be made on any attached control head. This feature
only applies to control heads in the All Active mode.
Procedure:
1 Press the Menu Select button directly below INTC to
activate the intercom feature of any of the control heads.
40
English
2 Press the PTT button to initiate an intercom transmission.
All control heads that are attached will receive the same
intercom call.
3 The display of the control heads receiving the intercom call
shows the alias/ID number of the transmitting control head.
4 Press the Menu Select button directly below EXIT to
deactivate the intercom feature.
OR
Press H to deactivate the intercom feature.
The intercom feature also deactivates when user initiates a
mode change. If the radio is on an emergency channel,
pressing of the EMERGENCY button or the emergency
footswitch button on any control head also deactivates the
intercom feature.
 One Active Mode
The One Active mode enables only one control head to be
visibly active at a time in a two control head system.
Note:
In the One Active mode, if more than two control heads
are present upon power up, the radio shows a FATAL
error EXTRA CH on the display of all attached control
heads.
The active control head commands the system normally while
the inactive control head is in remote mode with its display
shows REMOTE.
Note:
Only two (2) control heads are supported in the one
active mode.
Transceiver
Z1
ZONE CHAN
PWR
Follow the procedure below to change the command between
the two control heads.
Procedure:
Press the Menu Select button directly below F/R.
OR
Press the Menu Select button preprogrammed user button on
the keypad microphone.
Advanced Features
The Volume knob, DIM button, Front/Rear (F/R) softkey and
Emergency button remain active on the inactive control head,
while all other controls are disabled. Emergency footswitch and
VIP inputs remain active on the inactive control head. The VIP
input control head is configurable in the CPS and VIP should be
attached to the control head selected in the CPS.
SQL
Active Radio
REMOTE
F/R
Non-Active Radio
41
English
Contacts
Note:
This feature provides “address-book” capabilities on your radio.
Each entry corresponds to an alias (name) or ID (number) that
you use to initiate a call.
If the feature inactivity timer is enabled, your radio
automatically exits the feature when your radio is left
idle long enough for the time to expire. You will hear
the Menu Inactive Exit Tone upon feature exit.
Contacts manages up to 2,500 contact entries, alphabetically
sorted according to entry alias. Each alias can have up to 5 IDs
of different call types associated with it.
Additionally, each entry, depending on context (conventional,
trunking, or phone), associates with one or more of the four
types of calls: Phone Call, Selective Call, Private Call, or Call
Alert.
Advanced Features
Each entry within Contacts displays the following information:
• Call Alias (Name)
• Call ID (Number)
• Call Type (Icon)
• WACN ID (Astro 25 Trunking IDs only)
• System ID
Note:
Your radio must be preprogrammed to allow you to
add, edit, or delete the contact entries.
Your radio also supports a maximum of 50 call lists. Each list
can store up to 100 IDs (numbers).
42
English
Your radio is preprogrammed with a number of
contacts per Call Lists. Check with your dealer or
system administrator for more information.
 Making a Private Call from Contacts
Note:
Your radio must be preprogrammed to allow you to
use this feature.
Procedure:
Use the Options Menu.
1 > or < to CNTS.
2 Press the Menu Select button directly below CNTS to the
call list. The display shows Contact Alias.
3 > or < to the required subscriber alias.
4 Press the Menu Select button directly below OPTN.
5 > or < to CALL and press the Menu Select button directly
below SEL.
6 > or < to select the call type.
7 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm)
from your mouth.
display shows the subscriber alias.
9 Press and hold the PTT button to talk. The LED lights up
solid red.
OR
Release the PTT button to listen. The LED lights up solid
green.
10 If there is no voice activity for a programmed period of time,
the call ends.
OR
The call ends when it reaches the maximum ring time.
display shows the subscriber alias.
7 Press and hold the PTT button to talk. The LED lights up
solid red.
OR
Release the PTT button to listen. The LED lights up solid
yellow.
8 If there is no voice activity for a preprogrammed period of
time, the call ends.
OR
The call ends when it reaches the maximum ring time.
Advanced Features
8 Press the PTT button to initiate the call. During the call, the
6 Press the PTT button to initiate the call. During the call, the
OR
Use the PTT button:
1 > or < to CNTS.
2 Press the Menu Select button directly below CNTS.
3 > or < to the required subscriber alias.
4 Press the Menu Select button directly below CNTS. The
display shows Contact Alias.
5 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm)
from your mouth.
43
English
 Adding a New Contact Entry
Procedure:
1 > or < to CNTS.
2 Press the Menu Select button directly below CNTS. The
entries are alphabetically sorted.
3 > or < to {NEW CONTACT} and press the Menu Select
button directly below SEL.
4 The display shows NAME. Press the Menu Select button
directly below EDIT.
Use the keypad to enter the name.
Advanced Features
Press < to move one space to the left.
Press > to move one space to the right.
Press the Menu Select button below DEL to delete any
unwanted characters.
Press * to add a space.
Press 0 to toggle between mixed case mode, uppercase
mode, and lowercase mode.
Press # to toggle between numeric and letter mode.
5 Press the Menu Select button directly below OK once you
have entered the name.
OR
Press the Menu Select button directly below CNCL to return
to the previous screen.
44
English
6 > or < to {ADD NUMBER} and press the Menu Select button
directly below SEL. The display shows TYPE 1 .
7 Press Menu Select button directly below EDIT.
8 > or < to the required channel and press the Menu Select
button directly below OK.
9 > or < to NUMBER 1 and press the Menu Select button
directly below EDIT.
The display shows NUMBER 1 and a cursor appears.
Use the keypad to enter the number.
Press < to move one space to the left.
Press > to move one space to the right.
Press the Menu Select button directly below DEL to delete
any unwanted characters.
10 Press the Menu Select button directly below OK once you
have entered the number.
OR
Press the Menu Select button directly below CNCL to return
to the previous screen.
11 Press the Menu Select button directly below DONE once
you have finished.
12 The display shows  STORED, confirming that the
contact entry has been added.
13 The radio returns to the main Contacts screen.
 Adding a Contact to a Call List or Phone List
Procedure:
Procedure:
1 > or < to CNTS.
1 > or < to CNTS.
2 Press the Menu Select button directly below CNTS. The
2 Press the Menu Select button directly below CNTS. The
entries are alphabetically sorted.
3 > or < to the entry you want to delete and press the Menu
Select button directly below OPTN.
4 > or < to DELETE and press the Menu Select button directly
below SEL. The display shows  CONFIRM DEL?.
5 Select YES to delete the entry.
The display shows  DELETED and the radio
returns to the main screen for Contacts.
OR
Select NO to return to the main screen for Contacts.
entries are alphabetically sorted.
3 > or < to the entry you want to add to the call list and press
the Menu Select button directly below OPTN.
4 > or < to ADD TO CALLLST or ADD TO PHONLST and
press the Menu Select button directly below SEL.
5 > or < until the display shows {AVAILABLE} and press the
Advanced Features
 Deleting a Contact Entry
Menu Select button directly below ADD to add as a new
entry.
OR
> or < until the display shows  and its associated
number and press the Menu Select button directly below
RPLC to replace the existing entry.
6 The display shows  ADDED, confirming the
addition of the contact to the list.
7 The radio returns to the main display for Contacts.
45
English
 Editing a Contact in a Call List or a Phone List
 Editing an Entry Alias
Procedure:
1 > or < to CNTS.
2 Press the Menu Select button directly below CNTS. The
entries are alphabetically sorted.
3 > or < to the entry you want to edit and press the Menu
Select button directly below OPTN.
4 > or < to EDIT and press the Menu Select button directly
Advanced Features
below SEL.
5 > or < to the entry alias you wish to change and press the
Menu Select button directly below EDIT.
6 A cursor appears.
Use the keypad to edit the name.
Press < to move one space to the left.
Press > to move one space to the right.
Press the Menu Select button below DEL to delete any
unwanted characters.
Press * to add a space.
Press 0 to toggle between mixed case mode, uppercase
mode, and lowercase mode.
Press # to toggle between numeric and letter mode.
46
English
7 Press the Menu Select button directly below OK once you
have finished. The display returns to the Edit Contact
screen.
8 Press the Menu Select button directly below DONE to save
your changes and return to the main screen for Contacts.
 Editing as Entry ID
Procedure:
1 > or < to CNTS.
2 Press the Menu Select button directly below CNTS. The
entries are alphabetically sorted.
3 > or < to the entry you want to edit and press the Menu
Select button directly below OPTN.
4 > or < to EDIT and press the Menu Select button directly
below SEL.
5 > or < to the entry ID you wish to change and press the
Menu Select button directly below EDIT.
6 A cursor appears.
Use the keypad to edit the number.
Press < to move one space to the left.
Press > to move one space to the right.
Press the Menu Select button below DEL to delete any
unwanted characters.
7 Press the Menu Select button directly below OK once you
have finished. The display returns to the Edit Contact
screen.
8 Press the Menu Select button directly below DONE to save
your changes and return to the main screen for Contacts.
 Editing a Call Type
Procedure:
1 > or < to CNTS.
2 Press the Menu Select button directly below CNTS. The
entries are alphabetically sorted.
3 > or < to the entry you want to edit and press the Menu
Select button directly below OPTN.
4 > or < to EDIT and press the Menu Select button directly
below SEL.
5 > or < to TYPE and press the Menu Select button directly
Advanced Features
Press * to add a space.
Press 0 to toggle between mixed case mode, uppercase
mode, and lowercase mode.
Press # to toggle between numeric and letter mode.
below EDIT.
6 > or < to choose from the list of call types given and press
the Menu Select button directly below OK to select.
7 The display returns to the Edit Contact screen.
8 Press the Menu Select button directly below DONE to save
your changes and return to the main screen for Contacts.
47
English
Scan Lists
Scan lists are created and assigned to individual channels/
groups. Your radio scans for voice activity by cycling through
the channel/group sequence specified in the scan list for the
current channel/group.
This feature lets you change scan list members and priorities.
Note:
The maximum number of members for a trunking
priority monitor scan list is 50; for a conventional scan
list, 30; and for a talkgroup scan list, 250.
Your radio can support up to 200 different scan lists. These lists
must be preprogrammed by a qualified radio technician.
Procedure:
 Viewing a Scan List
2 Press the Menu Select button directly below SCNL. The
Procedure:
Advanced Features
 Editing the Scan List
1 > or < to SCNL.
display shows the lists that can be changed.
1 > or < to SCNL.
3 > or < to the entry you want to edit.
2 Press the Menu Select button directly below SCNL.
4 Press the Menu Select button directly below SEL to add
3 > or < to view the members on the list.
4 Press the H to exit the current display and return to the
Home screen.
48
English
and/or change the priority of the currently displayed channel
in the scan list.
OR
Press the Menu Select button directly below DEL to delete
the currently displayed channel from the scan list.
OR
Press the Menu Select button directly below RCL to view
the next member of the scan list.
5 > or < to select more channels to be added or deleted.
OR
Use the keypad to go directly to additional channels to be
added or deleted.
OR
Use the Mode Knob to select additional channels to be
added or deleted.
Home screen.
See Viewing and Changing the Priority Status on page 50
for more information on how to add and/or change the priority of
the currently displayed channel in the scan list.
 Changing the Scan List Status
Procedure:
1 Long press the preprogrammed Scan side button.
2 > or < to the member you want to edit.
5 Press H to exit scan list programming and return to the
Home screen.
Advanced Features
6 Press H to exit scan list programming and return to the
OR
Use the Mode Knob to select another scan list member.
3 Press the 3 button or press the Menu Select button
directly below SEL once to add the currently displayed
channel to the scan list.
OR
Press the 3 button or press the Menu Select button
directly below SEL, one or more times to change the scan
list status icon of the currently displayed channel.
4 > or < to select more list members whose scan status you
want to change.
OR
Use the keypad to go directly to that scan list member.
49
English
 Viewing and Changing the Priority Status
Procedure:
1 Below the SEL, DEL, and RCL screen, press the Menu
Select button directly below SEL to view and/or change the
priority status of the currently displayed channel.
OR
Below the SEL, DEL, and RCL screen, press the 3 button or
press the Menu Select button directly below SEL, one or
more times to view and/or change the scan list status icon of
the currently displayed channel.
Advanced Features
2 A Scan icon indicates that the current channel is in the scan
list as a non-priority channel. The LED lights up solid green.
OR
A Priority-Two Channel Scan icon indicates that the current
channel is in the scan list as the Priority-Two channel. The
LED blinks green.
OR
A Priority-One Channel Scan icon indicates that the current
channel is in the scan list as the Priority-One channel. The
LED rapidly blinks green. You hear all traffic on the PriorityOne channel, regardless of traffic on non-priority channels.
OR
No icon indicates that the current channel is deleted from
the scan list.
50
English
Scan
This feature allows you to monitor traffic on different channels
by scanning a preprogrammed list of channels.
 Turning Scan On or Off
Procedure:
Press the preprogrammed Scan button.
OR
Follow the procedure below.
1 > or < to SCAN.
2 Press the Menu Select button directly below SCAN.
3 The display shows SCAN OFF if scan is disabled. Press the
Menu Select button directly below SCAN to enable scan.
OR
The display shows SCAN ON and the scan status icon if
scan is enabled. Press the Menu Select button directly
below SCAN to disable scan.
4 The radio returns to the Home screen.
 Turning Scan On While Disregarding the Squelch
Code (Conventional Channels Only)
1 > or < to MON.
2 Press the Menu Select button directly below MON.
3 The brief MONITOR ON display indicates that the radio is
disregarding the squelch code.
While scanning for activity, you can still receive fleetwide,
system-wide, dynamic regrouping, incoming telephone
interconnect and Private Conversation/Call Alert calls.
Respond to these types of calls as you would normally on the
selected channel. However, when scanning different channels
while in talkgroup scan, incoming Private Conversation/Call
Alert calls may be missed.
 Transmitting While the Scan is On
 Radio Programmed for Talkback Scan
To transmit on the selected channel if another channel is active,
first turn scan off by pressing the Menu Select button below
SCAN momentarily.
 Radio Programmed for Non-Talkback Scan
Procedure:
1 Press the PTT button at any time to transmit on the selected
Advanced Features
Procedure:
The radio does not begin scanning again for a predetermined
hang time after you release the PTT button, allowing the other
party to respond. If the other party responds within the hang
time, scanning does not resume until the full hang time expires
after they have finished speaking, allowing the conversation to
be completed.
channel or fixed channel.
To make a Call Alert page, or Private Conversation call while
scanning, press either the Menu Select button directly below
PAGE or CALL. The call is entered on the selected channel and
scanning is halted until the call is exited by pressing H or
pressing the Menu Select button below either PAGE or CALL.
Procedure:
1 Press the PTT button to transmit on the channel indicated
by the display.
51
English
 Deleting a Nuisance Channel
 Changing Priorities Status While Scan is On
If a channel continually generates unwanted calls or noise
(termed a “nuisance” channel), you can temporarily remove the
unwanted channel from the scan list.
While the radio is scanning, the dynamic priority change feature
allows you to temporarily change any channel in a scan list
(except for the Priority-One channel) to the Priority-Two
channel.
This capability does not apply to priority channels or the
designated transmit channel.
Procedure:
1 When the radio is locked onto the channel to be deleted,
> or < to NUIS.
Advanced Features
2 Press the Menu Select button directly below NUIS.
 Restoring a Nuisance Channel
Procedure:
To restore the deleted nuisance channel, do one of the
following:
• Turn scan off, then on.
OR
• Change modes.
OR
• Turn off the radio, and then turn it back on.
Nuisance mode delete can be disabled by the system
administrator.
52
English
This change remains in effect until scan is turned off. Scan then
reverts to the preprogrammed (original) setting.
Procedure:
1 Press the Menu Select button directly below DYNP to
change the priority of a non-priority channel in the scan list
to Priority-Two.
2 Press H momentarily to exit the scan list and resume
scanning.
 Restoring Priorities in a Scan List
To restore the original channel priorities in a scan list, do one of
the following:
• Turn scan off, then on.
OR
• Change channels.
•
OR
Turn off the radio, and then turn it back on.
 Hang Up (HUB)
To temporarily suspend Scan Mode operation, remove the
control head from the Hang Up Box (HUB). You are allowed to
use the control head while scan is suspended. However, Priority
Member scanning is not suspended. This feature applies to all
Scan Lists and Scan Types. Scan is resumed once the control
head is returned to the holding clip and the preprogrammed
hang time has elapsed.
Note:
This feature allows your radio to work like a pager.
Even if other users are away from their radios, or if they are
unable to hear their radios, you can send them an individual
Call Alert page. You can also verify if a radio is active on the
system.
Depending on how your radio is programmed, when you make
an Enhanced Private Call, the radio either automatically sends
a Call Alert page if there is no answer after the maximum ring
time, OR when you press the PTT button.
Note:
This feature must be preprogrammed by a qualified
radio technician.
Advanced Features
Procedure:
Call Alert Paging
Priority Scan List members are continuously scanned
only when the Scan List, Designated Tx Member field
is set to “Talkback” in the radio programming.
Otherwise, all scan mode operation is suspended.
53
English
 Receiving a Call Alert Page
 Sending a Call Alert Page
Procedure:
Note:
When you receive a Call Alert page
1 You hear four repeating alert tone and the green LED blinks.
OR
You hear one alert tone and the green LED blinks if Call
Alert Tone Auto Reset is enabled.
2 The call received icons blinks and the display shows PAGE
RECEIVED.
3 Press the PTT button to answer.
Advanced Features
OR
Press any button to clear the Call Alert page.
See Making a Talkgroup Call on page 29 or Making a Private
Call (Trunking Only) on page 30 for more information.
If the feature inactivity timer is enabled, your radio
automatically exits the feature when your radio is left
idle long enough for the time to expire. You will hear
the Menu Inactive Exit Tone upon feature exit.
Procedure:
Press the preprogrammed Quick Access (One-Touch) Call
Alert Paging button to send a page to the preprogrammed ID
and proceed to Step 5 of the procedure below.
OR
Follow the procedure below.
1 > or < to PAGE.
2 Press the Menu Select button directly below PAGE.
3 > or < to select the required ID.
4 Press the PTT button to send the page.
5 The display shows PAGING... or .
6 If the call alert page is sent successfully, four highpitch tone
sounds and the display shows ACK RECEIVED.
OR
If the call alert page is not acknowledged, a low tone sounds
and the display shows NO ACKNOWLEDGE.
7 The radio returns to the Home screen.
54
English
OR
Press the Menu Select button directly below OK to return to
the main screen for Contacts.
Press the Menu Select button directly below OK to return to
the main screen for Contacts.
 In-Call User Alert
1 > or < to CALL.
You can enable and disable voice transmission, if needed.
2 Press the Menu Select button directly below CALL.
3 > or < to select the required ID, press the PTT button to
initiate the call.
4 If the target radio does not respond after a preprogrammed
period of time, the display shows SEND PAGE?.
5 Press the Menu Select button directly below YES to send
the call alert page.
OR
Press the Menu Select button directly below NO to exit the
screen without sending the call alert page.
6 The display shows PAGING....
7 If the call alert page is sent successfully, a tone sounds and
the display shows ACK RECEIVED.
OR
If the call alert page is not acknowledged, a low tone sounds
and the display shows NO ACKNOWLEDGE.
Procedure:
1 Make sure you are in Home mode where the default zone
and mode are being displayed.
2 > or < to scroll to the VMUT.
3 Press the Menu Select button directly below VMUT.
4 Press the Menu Select button directly below VMUT or the
Advanced Features
OR
Follow the procedure below.
VMut preprogrammed button again to turn the feature off
and you will be able to hear to normal dispatch calls.
Pressing the Menu Select button directly below VMUT or the
VMut programmed button momentarily toggles between Voice
mute on and Voice mute off. VOICE MUTE ON shown on the
display indicates that the radio is muted to all conventional
dispatch calls and affiliated trunking group calls.
8 The radio returns to the Home screen.
OR
55
English
Emergency Operation
The Emergency feature is used to indicate a critical situation.
If the Orange button is preprogrammed to send an emergency
signal, this signal overrides any other communication over the
selected channel.
Your radio supports 5 Emergency modes:
• Emergency Call
• Emergency Alarm
• Emergency Alarm with Call
Advanced Features
• Silent Emergency Alarm
• Special Considerations for Emergencies
Check with your dealer or system administrator for more
information on the programming of this feature.
Only one of the Emergency modes above can be assigned to
the preprogrammed Emergency button or the Emergency
footswitch.
Note:
56
English
To exit emergency at any time, press and hold the
preprogrammed Emergency button for about a
second.
 Sending an Emergency Alarm
This feature allows you to send a data transmission, which
identifies the radio sending the emergency, to the dispatcher.
Procedure:
1 Press the preprogrammed Emergency button. A tone
sounds and the display alternates EMERGENCY and the
home display.
2 A dispatcher acknowledgment ACK RECEIVED display
follows.
AND, Trunking Only:
A high-pitched tone indicates that the alarm has been
received by the trunked system’s central controller.
3 Press and hold the emergency button or the PTT button to
return to normal operation.
Procedure:
Procedure:
1 Press the preprogrammed Emergency button to activate
1 Press preprogrammed Emergency button.
2 A tone sounds and the display alternates EMERGENCY and
the home display.
OR
A short low-pitched tone sounds when the selected channel
does not support emergency.
3 Hold the microphone vertically 1 to 2 inches (2.0 to 2.5 cm)
from your mouth.
4 Press and hold the PTT button. Speak clearly into the
microphone.
the emergency call/alarm feature.
2 The display alternates EMERGENCY and the home display.
3 A high-pitched tone sounds, indicating that the alarm has
been received by the trunked system’s central controller.
A dispatcher acknowledgment (four high-pitched tones)
follows, accompanied by an ACK RECEIVED display.
4 Hold the microphone vertically 1 to 2 inches (2.0 to 2.5 cm)
from your mouth.
5 Press and hold the PTT button. Speak clearly into the
microphone.
5 Release the PTT to end the transmission.
6 Release the PTT to end the transmission.
6 Press and hold the preprogrammed Emergency button until
7 Press and hold the preprogrammed Emergency button until
a tone sounds to exit Emergency mode.
 Sending an Emergency Alarm with Emergency
Advanced Features
 Sending an Emergency Call (Trunking Only)
a tone sounds to exit Emergency mode.
Turning the radio off also cancels the emergency state.
Call
This feature allows you to send an Emergency Alarm to another
radio. Upon acknowledgement, both radios can communicate
over a preprogrammed Emergency channel.
If the radio has both emergency call and alarm features
enabled, it automatically proceeds to the call mode after the
alarm is acknowledged.
57
English
 Sending a Silent Emergency Alarm
 Special Considerations for Emergencies
This feature allows you to send an Emergency Alarm to another
radio without any audio or visual indicator.
• If you press the emergency button while in a channel that has
Upon acknowledgement, your radio’s microphone is
automatically activated, allowing you to communicate with the
other radio without pressing the PTT button.
• If the unit is out of the range of the system and/or the
This activated microphone state is also known as “hot mic”.
• If you press the emergency button, then change to a mode
Note:
If you press the PTT button during hot mic, and
continue to press it after the hot mic duration expires,
the radio continues to transmit until you release the
PTT button.
Advanced Features
Procedure:
1 Press the preprogrammed Emergency button to activate
the silent alarm feature.
2 Press and hold the emergency button until a tone sounds to
exit the silent alarm mode.
If silent emergency alarm is used with emergency call, pressing
the PTT button exits the silent mode and initiates the
emergency call.
58
English
no emergency capability, a low-pitched tone sounds.
emergency alarm is not acknowledged, a tone sounds and
the display shows NO ACKNOWLEDGE.
that has no emergency capability, the display shows NO
EMERGENCY and a continuous low-pitched tone sounds until
a valid emergency mode is selected or until the emergency is
cancelled.
• When an emergency is active, changing to another mode
where emergency is enabled (trunked or conventional)
causes an emergency alarm and/or emergency call to be
active on the new mode.
Advanced Features
Automatic Registration Service (ARS)
 Selecting or Changing ARS Mode
Data applications within the fixed network can determine the
presence of a device on the system and send data to the
device. For example: Text Messaging Service (TMS).
The Automatic Registration Service for the radio consists of two
(2) modes:
• ARS Server Mode (default mode)
• ARS Non Server Mode
Note:
The default ARS mode can be changed by a qualified
radio technician using the radio’s programming
software.
1 After the zone you want is displayed, toggle until the display
shows the required channel.
OR
Press and hold > or < to CHAN.
Press the Menu Select button directly below CHAN.
The display shows the current zone is not blinking, and the
channel is blinking.
2 > or < or rotate the Mode Knob to the required channel.
3 In ARS Server Mode, the display shows the User Login
Indicator icon, the zone, and ARSSVR.
OR
In ARS Non-Server Mode, the display shows the User Login
Indicator icon, the zone, and NONSVR.
OR
If the channel or mode selected is unprogrammed, the
display shows UNPROGRAMMED. Repeat Step 2.
Advanced Features
Procedure:
This feature provides an automated data application registration
for the radio. When you turn on the radio, the device
automatically registers with the server.
4 Press H to confirm the displayed zone and channel.
59
English
 Accessing the User Login Feature
 Logging In as a User
This feature allows you as the user to be associated with the
radio. With this association, every data application (Example:
Text Messaging Service) takes on a friendly username.
Procedure:
You can still send text messages without logging in as a user.
The user login feature only enables the recipient of your
message to identify you as the sender by assigning a username
to your message.
Advanced Features
Note:
Valid characters for a username entry are capital
letters (A – Z), small letters (a – z), numbers (0 – 9),
symbols (*, #, -, /), and the space character.
The maximum length for a username is eight (8)
characters. Usernames are not case sensitive in
server mode but are case sensitive in non-server
mode.
A predefined username may sometimes be invalid
because the programming software that is used to set
predefined usernames allows you to set usernames
comprising of eight (8) characters or more.
1 > or < to USER.
2 Press the Menu Select button directly below USER.
3 The display shows the User Login screen.
4 Press the Menu Select button directly below ID.
5 A blinking cursor appears beside ID. Use the keypad to
enter a username using the keypad multi-tap function.
OR
> or < to scroll through the list of predefined usernames.
Press the Menu Select button to select a predefined
username.
OR
Press and hold > or < to scroll through the list of predefined
usernames at a fast scroll rate.
Press the Menu Select button directly below LOGN to select
a predefined username.
6 If the selected predefined username has more than eight (8)
characters, or an invalid character in it, the display
momentary shows INVALID ID. Repeat Step 5.
OR
Press the Menu Select button directly below PIN.
7 A blinking cursor appears beside PIN.
60
English
Enter your Personal Identification Number (PIN) number.
The maximum PIN length is 4 digits. The PIN number will
appear as asterisks.
 Logging Out
Once the data application registration is completed, you can log
out.
9 In ARS server mode, the display shows the User Login
Procedure:
Indicator icon, the ID, IN PPROGRESS and CNCL.
OR
In ARS non-server mode, the display shows the User Login
Indicator icon, the ID, LOGGED IN and LOGT.
In non-ARS enabled mode, the display shows OFFLINE and
LOGT.
1 If the username is invalid, login fails and the user login
failure indicator (IP indicator) icon blinks. The display also
momentary shows LOGIN FAILED. Repeat step 5.
OR
If the PIN is invalid, login fails and the user login failure
indicator (IP indicator) icon blinks. The display also
momentary shows LOGIN FAILED. Repeat Step 7.
OR
Press the Menu Select button directly below CNCL to cancel
the login in progress screen and return to the initial user
login screen.
OR
Wait for the logged in confirmation screen. If the login
process is successful, the display shows the successful user
login indicator (IP indicator) icon and LOGGED IN and LOGT.
1 > or < to LOGT.
2 Press the Menu Select button directly below LOGT.
3 Display shows the User Login Indicator icon and CLEAR
PRIVATE DATA?.
4 Select YES to clear all your private data. The display shows
momentary PRIVATE DATA CLEARED.
OR
Select NO to keep your private data.
Note:
Advanced Features
8 Press the Menu Select button directly below LOGN.
Private data refers to all messages in the text
messaging Inbox, Draft and Sent folder. The next radio
user will be able to access your Inbox, Draft and Sent
messages if private data is not deleted.
61
English
Text Messaging Service (TMS)
This feature allows you to send and receive text messages. The
maximum length of characters for a text message is 200.
There are three (3) types of text messages:
• A new text message (free form message)
• A predefined message (quick text message)
Note:
If the feature inactivity timer is enabled, your radio
automatically exits the feature when your radio is left
idle long enough for the time to expire. You will hear
the Menu Inactive Exit Tone upon feature exit.
Press the Menu Select button directly below BACK at
any time to return to the previous screen.
• Drafts
Procedure:
Press the preprogrammed Data Feature button or the TMS
button to access the TMS feature screen.
OR
Press and hold the preprogrammed Data Feature button or the
TMS button to access the Inbox screen.
OR
Follow the procedure below.
• Sent
1 > or < to TMS.
• An edited quick text message
The main menu consists of the following options:
• Inbox
Advanced Features
 Accessing TMS Feature
• Compose
Note:
62
English
See Status Icons on page 18 for more details on the
TMS icons and TMS Menu Options on page 19 for
more details on each menu option.
2 Press the Menu Select button directly below TMS to access
the TMS feature screen.
3 > or < to scroll through the main menu options.
 Composing and Sending a New Text Message
During the uppercase and lowercase mode, multitapping the keys only scrolls through the letters. For
example, A->B->C, a->b->c.
6 Press the Menu Select button directly below OPTN once the
message is composed.
During the num lock mode, except for 1, pressing
the keypad only enters the numeric digits. Subsequent
presses of the same key inserts the same digit to the
text message (no multi-tap).
Procedure:
1 > or < to TMS.
2 Press the Menu Select button directly below TMS to access
the TMS feature screen.
3 Press the Menu Select button directly below COMP to see
the compose options.
4 Press the Menu Select button directly below NEW to
compose a new message.
5 A blinking cursor appears on the Compose screen.
Use the keypad to type or edit your message.
Press < to move one space to the left.
Press > to move one space to the right.
Press the Menu Select button directly below DEL to delete
any unwanted characters.
Press * to add a space.
7 > or < to SEND and press the Menu Select button directly
below SEND to send.
OR
> or < to BACK and press the Menu Select button directly
below BACK to return to Compose screen if you want to edit
the message.
8 > or < to scroll through the address list and press the Menu
Advanced Features
Note:
Press 0 to toggle between mixed case mode, uppercase
mode, and lowercase mode.
Press # to toggle between numeric and letter mode.
Select button below SEL to select the required address.
OR
> or < to {OTHER RECPNT} and press the Menu Select
button below EDIT.
A blinking cursor appears in the ENTER ADDRESS screen.
Use the keypad to type the address entry.
Press < to move one space to the left.
Press > to move one space to the right.
Press the Menu Select button below DEL to delete any
unwanted characters.
Press * to add a space.
Press 0 to toggle between mixed case mode, uppercase
mode, and lowercase mode.
Press # to toggle between numeric and letter mode.
63
English
9 Press the Menu Select button below SEND to send the
message.
OR
Press the PTT button to send the message.
10 The display shows the SEND MESSAGE screen and
SENDING MSG.
11 If the message is sent, a tone sounds and the display shows
MSG SENT.
OR
If the message is not sent, a low tone sounds and the
display shows SEND FAILED.
Advanced Features
If the message fails to send, the radio returns you to the main
TMS screen.
Note:
Note:
64
English
 Sending a Quick Text Message
Quick Text messages are messages that are predefined and
usually consist of messages that are used most frequently.
Each Quick Text message has a maximum length of 50
characters.
Procedure:
Press the preprogrammed Quick Text button and proceed to
Step 3.
OR
Follow the procedure below.
1 > or < to TMS.
2 Press the Menu Select button directly below TMS to access
the TMS feature screen.
You can append a priority status and/or a request reply
to your message. See Using the Priority Status and
Request Reply Features on page 66 for more
information.
3 Press the Menu Select button directly below COMP to
You can also select the DRFT option to save your
message in the Drafts folder to send it at a later time.
See Accessing the Drafts Folder on page 70 for
more details.
5 > or < to scroll through the list of messages and press the
access the compose options.
4 > or < to LIST.
Menu Select button directly below SEL to select the required
message.
6 The message appears on the Compose screen, with a
blinking cursor at the end of it.
Use the keypad to edit the message.
Press < to move one space to the left.
7 Press the Menu Select button directly below OPTN.
8 > or < to SEND and press the Menu Select button directly
below SEL to send the message.
9 > or < to scroll through the address list and highlight the
required address.
OR
> or < to {OTHER RECPNT} and press the Menu Select
button below EDIT.
A blinking cursor appears in the ENTER ADDRESS screen.
Use the keypad to type the address entry.
10 Press the Menu Select button below SEND to send the
message.
OR
Press the PTT button to send the message.
11 The display shows the screen and SENDING MSG.
12 If the message is sent, a tone sounds and the display shows
MSG SENT.
OR
If the message is not sent, a low tone sounds and the
display shows SEND FAILED.
If the message fails to send, the radio returns you to the main
TMS screen.
Note:
Advanced Features
Press > to move one space to the right.
Press the Menu Select button directly below DEL to delete
any unwanted characters.
Press * to add a space.
Press 0 to toggle between mixed case mode, uppercase
mode, and lowercase mode.
Press # to toggle between numeric and letter mode.
You can append a priority status and/or a request reply
to your message. See Using the Priority Status and
Request Reply Features on page 66 for more
information.
Press < to move one space to the left.
Press > to move one space to the right.
Press the Menu Select button below DEL to delete any
unwanted characters.
Press * to add a space.
Press 0 to toggle between mixed case mode, uppercase
mode, and lowercase mode.
Press # to toggle between numeric and letter mode.
65
English
 Using the Priority Status and Request Reply
Features
Before sending your message, you can append a priority
message and/or a request reply to your message.
 Appending or Removing a Priority Status to a Text
Message
Advanced Features
Note:
The Priority Message icon on a message does not
imply that the message gets higher priority over the
other messages when it is being transmitted. It is just
an indication that can be embedded into a message to
let the receiver know that the message is important.
Procedure:
After the outgoing message is composed (see Composing and
Sending a New Text Message on page 63 for more
information):
1 Press the Menu Select button directly below OPTN.
2 Press the Menu Select button directly below IMPT.
The priority status icon appears beside the normal message
icon on the label bar.
3 Press the Menu Select button directly below IMPT again.
The priority status icon and the normal message icon
disappear from the label bar.
66
English
 Appending or Removing a Request Reply to a Text
Message
Procedure:
After the outgoing message is composed (see Composing and
Sending a New Text Message on page 63 for more
information):
1 Press the Menu Select button directly below OPTN.
2 Press the Menu Select button directly below RQRP.
The reply status icon appears beside the normal message
icon on the label bar.
3 Press the Menu Select button directly below RQRP again.
The reply status icon and the normal message icon
disappear from the label bar.
 Appending a Priority Status and a Reply Request to a
Text Message
Procedure:
After the outgoing message is composed (see Composing and
Sending a New Text Message on page 63 for more
information):
1 Press the Menu Select button directly below OPTN.
2 > or < to IMPT and press the Menu Select button directly
below IMPT to indicate the message as important.
AND
> or < to RQRP and press the Menu Select button directly
 Managing Text Messages
below RQRP to request for a reply.
normal message icon on the label bar.
 Removing a Priority Status and a Reply Request from
a Text Message
When an outgoing message is indicated with priority status and
reply status icons, follow the procedure below to remove these
indicators.
Procedure:
1 Press the Menu Select button directly below OPTN.
2 > or < to IMPT and press the Menu Select button directly
below IMPT to remove the priority status icon.
AND
> or < to RQRP and press the Menu Select button directly
below RQRP to remove the reply status icon.
3 The priority status, reply status and normal message icons
disappear from the label bar.
 Receiving a Text Message
Note:
When you receive a message that is flagged with the
”Request Reply” icon, you must manually respond to
the sender that you have received the message. The
system will not automatically send back a notification
that the radio has received such message.
Procedure:
When you receive a message, press and hold the
preprogrammed Data Feature button or the TMS Feature
button to access the Inbox and go to Step3.
OR
Follow the procedure below.
Advanced Features
3 The priority status and reply status icons appear beside the
1 The new message icon appears and the display
momentarily shows NEW MSG.
2 Press the Menu Select button directly below TMS to access
the message.
3 The display shows alias or ID with the sender of the latest
received message on top.
67
English
 Viewing a Text Message from the Inbox
• Select RPLY to reply the message.
The Inbox can hold up to thirty (30) messages.
• Select DEL to delete the message.
Advanced Features
Note:
68
> or < to read the message if fills more than one
• Select BACK to return to the previous screen.
screen.
Note:
Procedure:
Press the preprogrammed Data Feature button or the TMS
Feature button to access the TMS feature screen, and proceed
to Step 3.
OR
Press and hold the preprogrammed Data Feature button or the
TMS Feature button to access the Inbox screen and proceed to
Step 4.
OR
Follow the procedure below.
1 > or < to TMS.
2 Press the Menu Select button directly below TMS to access
the TMS feature screen.
3 Press the Menu Select button below INBX to view Inbox
feature screen.
4 The display shows alias or IDs, with the sender of the latest
received message.
While on the review message screen, press the Menu Select
button directly below RPLY, DEL, or BACK to access the option.
English
The icon at the top right corner of the screen indicates
the status of the message. See Text Messaging
Service (TMS) on page 62 for more information.
 Replying to a Received Text Message
The original date and time stamp, address and
message content is automatically appended to the
reply message.
Procedure:
1 > or < to the required aliases or ID and press the Menu
Select button below SEL to view the message.
2 Press the Menu Select button directly below RPLY to reply
to a message.
3 > or < to NEW and press the Menu Select button directly
below NEW.
OR
> or < to LIST and press the Menu Select button directly
below LIST for a predefined message.
OR
> or < to scroll through the list of messages and press the
Menu Select button directly below SEL to select the required
message.
6 Press the Menu Select button directly below OPTN once
you have finished writing the message.
7 > or < to SEND and press the Menu Select button directly
below SEND to send the message.
8 The display shows the Send Message screen and
Advanced Features
Note:
Press > to move one space to the right.
Press the Menu Select button below DEL to delete any
unwanted characters.
Press * to add a space.
Press 0 to toggle between mixed case mode, uppercase
mode, and lowercase mode.
Press # to toggle between numeric and letter mode.
SENDING MSG.
Press the Menu Select button directly below BACK at any time
to return to the previous screen.
Note:
You can append a priority message and/or a request
reply to your message. Using the Priority Status and
Request Reply Features on page 66 for more
information.
4 A blinking cursor appears on the screen.
OR
The predefined message appears on the Compose screen,
with a blinking cursor at the end of it.
5 Use the keypad to type or edit your message.
Press < to move one space to the left.
69
English
 Accessing the Drafts Folder
 Managing Sent Text Messages
This folder stores the messages that were saved previously.
The Drafts folder can hold up to 10 messages. The oldest draft
in the folder is deleted when the 11th message comes in.
Once a message is sent to another radio, it is saved in the Sent
folder. The most recent sent text message is always added to
the top of the Sent list.
Procedure:
The Sent folder is capable of storing a maximum of ten (10) last
sent messages. When the folder is full, the oldest text message
in the folder is deleted when the 11th message comes in.
1 > or < to TMS.
2 Press the Menu Select button directly below TMS to access
the TMS feature screen.
3 > or < to DRFT and press the Menu Select button below
DRFT.
Advanced Features
4 The display shows the first draft message.
Press the Menu Select button directly below EDIT, DEL, or
BACK to access the option.
 Viewing a Sent Text Message
The icon at the top right corner of the screen indicates the
status of the message. See Text Messaging Service (TMS) on
page 62 for more information.
Procedure:
• Select DEL to delete the message.
Press the preprogrammed Data Feature button or the TMS
Feature button to access the TMS feature screen, and proceed
to Step 3.
OR
Follow the procedure below.
• Select BACK to return to the previous screen.
1 > or < to TMS.
• Select EDIT to edit the message before sending it.
2 Press the Menu Select button directly below TMS to access
the TMS feature screen.
3 > or < to SENT and press the Menu Select button below
SENT.
70
English
Press the Menu Select button directly below OPTN, DEL, or
BACK to access the option.
• Select DEL to delete the message.
• Select BACK to return to the previous screen.
Note:
The icon at the top right corner of the screen indicates
the status of the message. See Text Messaging
Service (TMS) Icons on page 18 for more information.
 Sending a Sent Text Message
Procedure:
1 Press the Menu Select button directly below OPTN while
viewing the message.
2 > or < to SEND and press the Menu Select button directly
below SEND to send the message.
4 Press the Menu Select button below SEND or the PTT
button to send the message.
5 The display shows the Send Message screen and
SENDING MSG.
6 Press the Menu Select button directly below BACK to return
Advanced Features
• Select OPTN to send to the message.
Press > to move one space to the right.
Press the Menu Select button below DEL to delete any
unwanted characters.
Press * to add a space.
Press 0 to toggle between mixed case mode, uppercase
mode, and lowercase mode.
Press # to toggle between numeric and letter mode.
to the previous screen.
Note:
You can append a priority message and/or a request
reply to your message. See Using the Priority Status
and Request Reply Features on page 66 for more
details.
3 > or < to scroll through the address list and highlight the
required address.
OR
> or < to {OTHER RECPNT} and press the Menu Select
button below EDIT.
A blinking cursor appears in the ENTER ADDRESS screen.
Use the keypad to type the address entry.
Press < to move one space to the left.
71
English
 Deleting Text Messages
Procedure:
From the Inbox, Draft, or Sent screen:
1 > or < to scroll through the messages.
2 Press the Menu Select button directly below DEL to view the
delete options.
3 Press the Menu Select button directly below CURR to delete
Advanced Features
the current message.
OR
Press the Menu Select button directly below ALL to delete
all the messages.
Secure Operations
Secure radio operation provides the highest commercially
available level of voice security on both trunked and
conventional channels.
Unlike other forms of security, Motorola digital encryption
provides signaling that makes it virtually impossible for others to
decode any part of an encrypted message.
 Managing Encryption
Note:
Refer to the Key-Variable Loader (KVL) manual for
equipment connections and setup.
 Loading a Single Encryption Key
Procedure:
1 Attach the KVL to your radio. Upon attaching the KVL, the
radio display shows KEYLOADING.
2 Press the Menu Select button below TARGET.
3 Press the Menu Select button below LOAD.
4 Press the Menu Select button below KEY.
5 > or < to required key.
6 Press the Menu Select button below LOAD to load the key
72
English
to your radio.
7 When the key has been loaded successfully, the radio
sounds a short tone for single-key radios.
This feature allows the radio to be equipped with as many as 64
different encryption keys and supports the DES-OFB algorithm.
There are two types of multikey:
Procedure:
1 Attach the KVL to your radio.
2 Press the Menu Select button below TARGET.
3 Press the Menu Select button below LOAD.
4 Press the Menu Select button below GROUP.
5 > or < to required group.
6 Press the Menu Select button below LOAD to load the key
to your radio.
7 Your mobile radio display shows KEYLOADING when it is
loading key(s) from KVL.
• Conventional Multikey – The encryption keys can be tied
(strapped), on a one-per-channel basis, through Customer
Programming Software. In addition, you can have operatorselectable keys, operator-selectable keysets, and operatorselectable key erasure. If talkgroups are enabled in
conventional, then the encryption keys are strapped to the
talkgroups.
• Trunked Multikey – If you use your radio for both
conventional and trunked applications, you have to strap your
encryption keys for trunking on a per-talkgroup or
announcement-group basis. In addition, you may strap a
different key to other features, such as dynamic regrouping,
failsoft, or emergency talkgroup. You can have operatorselectable key erasure.
Advanced Features
 Loading the Group Encryption Keys
 Using the Multikey Feature
8 When the key has been loaded successfully, the radio
sounds an alternating tone for multikey radios.
73
English
 Selecting an Encryption Key (Conventional Only)
 Enabling Secure Transmission
Procedure:
Procedure:
1 > or < to KEY.
1 > or < to SEC and Press the Menu Select button directly
2 Press the Menu Select button directly below KEY. The
display shows the last user-selected and stored encryption
key, and the available menu selections.
3 > or < to scroll through the encryption keys.
OR
Use the keypad to enter the number of the desired key.
Advanced Features
4 Press the Menu Select button directly below SEL to save the
newly selected key and return to the Home screen.
OR
Press H, the PTT button, or the Menu Select button directly
below EXIT to exit.
Note:
If the selected key is erased, a momentary keyfail tone
sounds and the display shows KEY FAIL.
OR
If the selected key is not allowed, a momentary illegal
key tone sounds and the display shows ILLEGAL KEY.
below SEC. The display shows m and the current key if
multi-key has been enabled.
2 Monitor the mode to be sure it is not in use.
3 Press PTT button to transmit.
Note:
If the selected channel is preprogrammed for clearonly operation – when you press the PTT button, an
invalid mode tone sounds and the display shows
CLEAR TX only.
The radio does not transmit until you disable the
secure mode.
 Accessing the Secure Feature
Procedure:
1 > or < to SEC.
2 Press and hold the Menu Select button directly below SEC
to display Secure feature screen.
3 The display shows the Secure screen.
74
English
 Selecting a Keyset
screen.
 Erasing the Selected Encryption Keys
For example, you could have a group of three keys structured to
one keyset, and another group of three different keys structured
to another keyset; by changing keysets, you would
automatically switch from one set of keys to the other.
This feature allows you to erase all or selected encryption keys.
Every channel to which one of the original keys was tied now
has the equivalent new key instead.
2 Press the Menu Select button directly below ERAS. The
Note:
Press H, the PTT button, or the EXIT menu selection
to exit this menu at any time without changing the
keyset selection.
Procedure:
1 > or < to KSET.
2 Press the Menu Select button directly below KSET.
The display shows the last user-selected and stored keyset,
and the available keyset menu selections.
3 > or < to scroll through the keysets.
OR
Use the keypad to enter the number of the desired keyset.
Procedure:
1 > or < to ERAS.
display shows the last user-selected and stored encryption
key, and the available menu selections.
3 > or < to the desired encryption key.
Advanced Features
This feature allows you to select one or more groups of several
encryption keys from among the available keys stored in the
radio.
5 The radio exits keyset selection and returns to the Home
OR
Use the keypad to enter the number of the desired key.
4 Press the Menu Select button directly below ALL to delete
all keys.
OR
Press the Menu Select button directly below SNGL to delete
current shown key.
OR
Press the Menu Select button directly below ABRT to abort
this screen and return to Home screen.
4 Press the Menu Select button directly below SEL to save the
newly selected keyset.
75
English
 Requesting an Over-the-Air Rekey
This feature, also known as OTAR, allows the dispatcher to
reprogram the encryption keys in the radio remotely. The
dispatcher performs the rekey operation upon receiving a rekey
request from the user.
Procedure:
1 > or < to REKY.
2 Press the Menu Select button directly below REKY.
Advanced Features
3 Press the PTT button to send the rekey request.
OR
Press the PTT button again, or the H or Emergency button,
to exit the feature and transmit in normal mode.
4 If the rekey operation fails, a bad-key tone sounds and the
display shows REKEY FAIL.
Note:
The rekey operation failure indicates that your radio
does not contain the Unique Shadow Key (USK). This
key must be loaded into the radio with the key-variable
loader (KVL) before the rekey request can be sent.
Refer to your local key management supervisor for
more information.
The Global Positioning System (GPS)
This feature uses information from the Global Positioning
System (GPS) satellites orbiting the Earth to determine the
approximate geographical location of your radio, expressed as
latitude and longitude. The availability and accuracy of this
location information (and the amount of time that it takes to
calculate it) varies depending on the environment in which you
are using the GPS feature.
For example, GPS location fixes are very difficult to obtain
indoors, in covered locations, between high buildings, or in
situations where you have not established a clear broad view of
the sky.
 Understanding the GPS Feature
The GPS technology uses radio signals from earth orbiting
satellites, to establish the location co-ordinates, maximizing
your view of clear unobstructed sky is essential for optimum
performance.
Where adequate signals from multiple satellites are not
available (usually because you cannot establish a view of a
wide area of the sky), the GPS feature of your radio will not
work. Such situations include but are not limited to:
• In underground locations
• Inside of buildings, trains, or other covered vehicles
76
English
 Enhancing GPS Performance
• Between tall buildings or under dense tree-cover
Sometimes, the GPS feature may be unable to complete a
location calculation successfully. You then see a message
indicating that your radio cannot connect to enough visible
satellites.
• In temperature extremes outside the operating limits of your
radio
Even where location information can be calculated in such
situations, it may take longer to do so, and your location
estimate may not be as accurate. Therefore, in any emergency
situation, always report your location to your dispatcher.
Note:
Even where adequate signals from multiple satellites
are available, your GPS feature only provides an
approximate location, usually within 20 meters from
your actual location, but sometimes further away.
To maximize the ability of your radio to determine a fix, please
note the following guidelines:
• For your initial fix, hold the radio in the face position.
• Stay in the open. The GPS feature works best where there is
nothing between your radio and a large amount of open sky.
 The Outdoor Location Feature (Using GPS)
Keep in mind that the accuracy of the location information and
the time it takes to obtain it varies depending upon
circumstances, particularly the ability to receive signals from an
adequate number of satellites.
This feature allows you to determine your current location using
a location menu, as well as your current distance and bearing in
relation to another location. Radio location may be requested
and reported over-the-air.
Note:
Your radio stores up to a maximum of sixty (60) programmable
location coordinates, also known as waypoints. When the
memory is full, the next waypoints automatically replaces the
oldest waypoints in the radio.
The satellites used by the GPS feature are controlled
by the U.S. government and are subject to changes
implemented in accordance with the Department of
Defense GPS user policy and the Federal Radio
Navigation Plan. These changes may affect the
performance of the GPS feature on your radio.
Advanced Features
• Under any other metal or concrete roof or structure
77
English
The radio also stores four (4) preprogrammed waypoints. These
coordinates cannot be deleted.
Programmable Waypoints
Preprogrammed Waypoints
Fixed location coordinates:
• Home
User-configurable location
coordinates.
• Emergency
• Last Known Location
Advanced Features
• Destination
Only the alias is editable, not
the coordinates.
The Home and Destination
coordinates are editable.
Coordinates can be deleted
one at a time, or all at once.
Coordinates cannot be
deleted.
Note:
78
English
If the feature inactivity timer is enabled, your radio
automatically exits the feature when your radio is left
idle long enough for the time to expire. You will hear
the Menu Inactive Exit Tone upon feature exit.
 Accessing the Outdoor Location Feature
Note:
An ON menu key may be present on the location menu
if it is preprogrammed by the dealer or system
administrator.
Procedure:
1 > or < to LOC.
2 Press the Menu Select button directly below LOC. The
display shows LOCATION OFF .
3 Press the Menu Select button directly below ON to turn on
the GPS. The display shows PREVIOUS LOC .
4 > or < to check the longitude, time and date of the last
successful location fix.
5 Press the Menu Select button directly below RFSH to obtain
a new location fix.
6 The top line temporarily displays PLEASE WAIT while the
new location is being determined.
While the new location is being determined, the location
signal can be a solid or blinking icon.
7 Once the location coordinates are fixed, the display shows
the current latitude. Toggle to see the longitude, time and
date.
The location coordinates are updated automatically every
five seconds while the location signal is present.
8 Press the Menu Select button directly below EXIT to exit
The radio also exits the menu if the emergency button is
pressed.
 Saving a Waypoint
Procedure:
OR
While in the current location display:
Follow the procedure below to turn off the GPS (This feature is
enabled by a qualified radio technician.):
1 Press the Menu Select button directly below OPTN.
1 > or < to LOC.
2 Press the Menu Select button directly below LOC. The
display shows PREVIOUS LOC .
3 > or < to check the longitude, time and date of the last
successful location fix.
4 Press the Menu Select button directly below OPTN.
5 > or < to TURN OFF GPS (if preprogrammed).
6 Press the Menu Select button directly below SEL to turn off
the GPS. The display shows LOCATION OFF.
7 Press the Menu Select button directly below EXIT to exit
the feature and return to the main screen.
OR
Press H or the PTT button (if preprogrammed) to exit this
menu.
2 > or < to SAVE AS WAYPT and press the Menu Select
button directly below SEL.
3 A blinking cursor appears in the screen. Use the keypad to
type the alias via multi-tap.
Press < to move one space to the left.
Advanced Features
the feature and return to the main screen.
OR
Press H or the PTT button (if preprogrammed) to exit this
menu.
Press > to move one space to the right.
Press the Menu Select button below DEL to delete any
unwanted characters.
Press * to add a space.
Press 0 to toggle between mixed case mode, uppercase
mode, and lowercase mode.
Press # to toggle between numeric and letter mode.
4 Press the Menu Select button directly below OK once you
are done.The display shows SAVED AS .
OR
Press the Menu Select button directly below CNCL to return
to previous screen.
79
English
5 Press H or the PTT button (if preprogrammed) to exit this
menu.
 Viewing a Saved Waypoint
Advanced Features
Procedure:
 Editing the Alias of a Waypoint
Procedure:
While in the current location display:
1 Press the Menu Select button directly below OPTN.
While in the current location display:
2 > or < to WAYPOINTS.
1 Press the Menu Select button directly below OPTN.
3 Press the Menu Select button directly below SEL.
2 > or < to WAYPOINTS.
4 > or < to desired waypoints.
3 Press the Menu Select button directly below SEL.
5 Press the Menu Select button directly below OPTN.
4 > or < to desired waypoint.
6 > or < to EDIT NAME and press the Menu Select button
5 Press the Menu Select button directly below OPTN. The
display shows VIEW.
6 Press the Menu Select button directly below SEL.
7 > or < again to view longitude, time and date the waypoint
was detected.
8 Press the Menu Select button directly below BACK to return
to previous Waypoint screen.
OR
Press H or the PTT button (if preprogrammed) to exit this
menu.
80
English
directly below SEL.
7 A blinking cursor appears in the Edit Name screen.
Use the keypad to edit the alias.
Press < to move one space to the left.
Press > to move one space to the right.
Press the Menu Select button below DEL to delete any
unwanted characters.
Press * to add a space.
Press 0 to toggle between mixed case mode, uppercase
mode, and lowercase mode.
Press # to toggle between numeric and letter mode.
8 Press the Menu Select button directly below OK once you
are done.
OR
Press the Menu Select button directly below CNCL to return
to the Waypoints main screen.
10 Press H or the PTT button (if preprogrammed) to exit this
menu.
 Editing the Coordinates of a Waypoint
Procedure:
While in the current location display:
1 Press the Menu Select button directly below OPTN.
2 > or < to WAYPOINTS and press the Menu Select button
directly below SEL.
3 > or < to desired waypoints.
4 Press the Menu Select button directly below OPTN.
5 > or < to EDIT LOCATION and press the Menu Select
button directly below SEL.
6 The first number blinks.
Press < to move to the previous number/coordinates.
Press > to move to the next number/coordinates.
Press U or D to change the North (N), South (S), East (E)
or West (W) direction.
7 A blinking cursor appears in the EDIT LOCATION screen.
Press < to move one space to the left.
Press > to move one space to the right.
Press the Menu Select button below Del to delete any
unwanted characters.
8 Press the Menu Select button directly below OK once you
are done.
OR
Press the Menu Select button directly below CNCL to return
to the previous screen.
Advanced Features
9 The display shows  UPDATED.
Press the Menu Select button below EDIT to change the
number/coordinates.
9 Press the Menu Select button directly below OK once you
are done with the new coordinates.
OR
Press the Menu Select button directly below CNCL to return
to the previous screen then skip to step 11.
10 The display shows {HOME} UPDATED and the radio returns
to the Waypoints main screen.
OR
The display shows {DESTINATION} UPDATED and the
radio returns to the Waypoints main screen.
11 Press H or the PTT button (if preprogrammed) to exit this
menu.
81
English
 Deleting a Single Saved Waypoint
 Deleting All Saved Waypoints
Procedure:
Procedure:
While in the current location display:
1 Press the Menu Select button directly below OPTN.
1 Press the Menu Select button directly below OPTN.
2 > or < to WAYPOINTS and press the Menu Select button
2 > or < to WAYPOINTS.
3 Press the Menu Select button directly below SEL.
4 > or < to desired waypoints.
Advanced Features
5 Press the Menu Select button directly below OPTN.
OR
Press the Menu Select button directly below DEL and then
skip to step 7.
6 > or < to DELETE and press the Menu Select button directly
below SEL.
7 The display shows  CONFIRM DEL?.
8 Press the Menu Select button directly below YES to delete.
The display shows  DELETED.
OR
Press the Menu Select button directly below NO to return to
previous Waypoint screen.
9 Press H or the PTT button (if preprogrammed) to exit this
menu.
82
English
directly below SEL.
3 > or < to desired waypoints and press the Menu Select
button directly below OPTN.
4 > or < to DELETE ALL and press the Menu Select button
directly below SEL.
5 The display shows ALL SAVED WAYP CONFIRM DEL?.
6 Press the Menu Select button directly below YES to delete.
The display shows ALL SAVED WAYP DELETED.
OR
Press the Menu Select button directly below NO to return to
previous Waypoint screen.
7 Press H or the PTT button (if preprogrammed) to exit this
menu.
 Measuring the Distance and Bearing from a Saved
Waypoint
1 Press the Menu Select button directly below OPTN.
2 > or < to DIST FRM HERE and press the Menu Select button
directly below SEL.
3 > or < to the required waypoint, and press the Menu Select
button directly below SEL.
4 The display shows the distance and bearing from the current
to the selected coordinates.
5 Press the Menu Select button directly below BACK to return
Mode
When the Emergency feature is activated by pressing the
emergency button, the radio exits the Location menu and
returns to the home (default) display so that you can see which
channel the emergency signal is going out on.
However, you may re-enter the Location menu while still in
emergency mode, provided that Silent Emergency has not been
activated.
If you have turned Location off using the ON/OFF menu key, it
automatically turns back on when Emergency is activated.
If there is a solid location signal during Emergency, the current
location and the location information received is saved as
Emergency and Last Known Location waypoints, respectively.
Advanced Features
Procedure:
While in the current location display:
 Using the Location Feature While in Emergency
to the previous Waypoint screen.
OR
Press H or the PTT button (if preprogrammed) to exit this
menu.
83
English
Trunking System Controls
 Using the Failsoft System
The failsoft system ensures continuous radio communications
during a trunked system failure. If a trunking system fails
completely, the radio goes into failsoft operation and
automatically switches to its failsoft channel.
The failsoft condition is indicated by a faint beeping tone every
nine seconds (radio unsquelched) until the trunking system
returns to normal operation.
Advanced Features
To continue, in Failsoft, to communicate with other talkgroups,
refer to the following procedure.
Procedure:
1 Rotate the Mode Knob to change to a different repeater
frequency.
2 Press the PTT button to talk, and release the button to
listen.
When the trunking system returns to normal operation, your
radio automatically leaves failsoft operation and returns to
trunked operation.
84
English
 Going Out-of-Range
OUT OF RANGE when your radio goes out of the range of the
system, it can no longer lock onto a control channel.
Procedure:
1 A low-pitched tone sounds.
AND/OR
The display shows the currently selected zone/channel
combination and OUT OF RANGE.
2 Your radio remains in this out-of-range condition until:
It locks onto a control channel.
OR
It locks onto a failsoft channel.
OR
It is turned off.
 Locking and Unlocking a Site
The SmartZone® feature extends communications beyond the
reach of a single-trunked site (antenna location) when operating
in a SmartZone system. SmartZone units provide expanded
wide-area coverage.
This feature allows your radio to lock onto a specific site and not
roam among wide-area talkgroup sites. This feature should be
used with caution, since it inhibits roaming to another site in a
wide-area system.
SmartZone automatically switches the radio to a different site
when the current site signal becomes unacceptable. This
usually happens when the vehicle in which the radio is located
is driven out of the range of one site, and into the range of
another.
Procedure:
Use the preprogrammed Site Lock/Unlock button to toggle the
lock state between locked and unlocked.
OR
Follow the procedure below.
Under normal conditions, a SmartZone-enabled radio functions
invisibly to the operator. However, the operator does have some
manual controls on the Control Head – the RSSI menu entry.
This button can be used to check, or change, the SmartZone
operation.
1 > or < to SITE.
 Using Site Trunking Feature
If the zone controller loses communication with any site, that
site reverts to site trunking.
The display shows the currently selected zone/channel
combination and SITE TRUNKING.
Note:
Advanced Features
 SmartZone®
2 Press the Menu Select button directly below SITE.
3 Press the Menu Select button directly below LOCK to lock
the site.
OR
Press the Menu Select button directly below UNLK to unlock
the site.
4 The radio saves the new site lock state and returns to the
Home screen.
When this occurs, you can communicate only with
other radios within your trunking site.
85
English
 Viewing and Changing a Site
 Changing the Current Site
This feature allows you to view the number of the current site or
force your radio to change to a new one.
Procedure:
 Viewing the Current Site
Procedure:
1 Press the preprogrammed Site Search button.
OR
> or < to RSSI.
2 The display momentarily shows the name of the current site
Advanced Features
and its corresponding received signal strength indicator
(RSSI).
86
English
1 Press and hold down the preprogrammed Site Search
button.
OR
Press and hold down the Menu Select button directly below
RSSI.
2 A tone sounds and the display momentarily shows
SCANNING SITE.
When the radio finds a new site, it returns to the Home screen.
 Initiating an Announcement
The announcement capability allows you to make
announcements to the entire user group, as well as monitor
talkgroup calls and other announcements.
If your radio has been programmed to allow announcement
calls:
Announcement calls are handled in two different ways,
depending on the trunked central controller configuration. The
two types are called ruthless and non-ruthless preemption.
1 Press the Mode Knob to locate the announcement-group
• Ruthless Preemption:
When a ruthless preemption announcement call is initiated,
the requesting radio begins transmitting immediately. All
associated talkgroup calls taking place on other channels are
immediately halted, and the radios are steered to the
announcement call.
Procedure:
mode.
2 Press the microphone PTT button to initiate the
announcement.
Advanced Features
 Trunked Announcement
Transmitting radios continue to transmit until the PTT button
is released, at which time they also unmute for the
announcement call. Individual calls (Private Conversation and
telephone interconnect) are not affected.
• Non-Ruthless Preemption:
When a non-ruthless preemption announcement is initiated,
the initiating unit receives a telephone-type busy tone,
followed by a call back when all associated talkgroup
conversations end.
Once an announcement call is pending, any attempts by
other users to initiate a talkgroup call will result in a
telephone-type busy tone. These users will not receive a call
back until the announcement call is complete.
87
English
Utilities
Note:
 Viewing Recent Calls List
This feature allows you to view the recent incoming and
outgoing call information of the following call types:
 Selecting the Power Level
• Call Alert
You can select the power level at which your radio transmits.
The radio always turns on to the default setting.
• Selective Call
Note:
Advanced Features
• Private Call
88
If the feature inactivity timer is enabled, your radio
automatically exits the feature when your radio is left
idle long enough for the time to expire. You will hear
the Menu Inactive Exit Tone upon feature exit.
This feature must be preprogrammed by a qualified
radio technician.
• Phone Call (Outgoing only)
Settings:
Note:
• Select LOW for a shorter transmitting distance and to
The radio can also be preprogrammed to log the radio
IDs associated with incoming Dispatch Calls. Check
with your dealer or system administrator for more
information.
Procedure:
1 > or < to RCNT.
2 Press the Menu Select button directly below RCNT to
access the Recent Calls feature screen.
3 > or < to scroll through the list.
4 Press the Menu Select button directly below BACK to return
to Home screen.
OR
Press H or the PTT button to return to the Home screen.
English
conserve power.
• Select HIGH for a longer transmitting distance.
Procedure:
Use the preprogrammed Transmit Power Level Switch to
toggle transmit power level between high and low power.
OR
Follow the procedure below.
1 > or < to PWR.
2 Press the Menu Select button directly below PWR.
3 The display shows LOW POWER and the low power icon.
 Selecting a Radio Profile
This feature allows you to manually switch the visual and audio
settings of the radio. The display, backlight, alert tones, and
audio settings are defined according to the preprogrammed
radio settings of each radio profile.
4 Press the Menu Select button directly below SEL to select
the required radio profile.
OR
Press the Menu Select button directly below EXIT to exit
the screen without making any changes.
5 The radio returns to the Home screen. The profile name on
the Home screen indicates the current selected radio profile.
 Controlling the Display Backlight
You can have up to a maximum of twelve (12) radio profiles
programmed into your radio by a qualified radio technician.
You can enable or disable the radio’s display backlight as
needed, if poor light conditions make the display difficult to read.
Note:
Depending on how your radio is preprogrammed, you can also
maintain a minimum backlight level on the radio’s display.
If the feature inactivity timer is enabled, your radio
automatically exits the feature when your radio is left
idle long enough for the time to expire. You will hear
the Menu Inactive Exit Tone upon feature exit.
Procedure:
Use the preprogrammed Profile button and proceed to Step 3.
OR
Follow the procedure below.
Advanced Features
OR
The display shows HIGH POWER and the high power icon.
Procedure:
Note:
Press the DIM button to toggle the backlight off or on.
OR
Press any key of the keypad, the Menu Select or
Menu Navigation buttons, or any programmable radio
controls or buttons to turn the backlight on.
1 > or < to PRFL.
2 Press the Menu Select button directly below PRFL to
access the Profiles feature screen.
3 > or < to scroll through the menu selections.
89
English
 Turning Keypad Tones On or Off
 Turning Voice Mute On or Off
You can enable and disable keypad tones if needed.
You can enable and disable voice muting of the affiliated
trunking talkgroup or selected conventional channel, if needed.
Procedure:
Press the preprogrammed Keypad Mute button to turn the
tones off or on.
OR
Follow the procedure below.
1 > or < to MUTE.
2 Press the Menu Select button directly below MUTE.
Advanced Features
3 The display momentarily shows TONES OFF, indicating that
the keypad tones are disabled.
OR
The display momentarily shows TONES ON, and a short
tone sounds, indicating that the keypad tones are enabled.
90
English
Procedure:
Press the preprogrammed Voice Mute button to turn the feature
off or on.
OR
Follow the procedure below.
1 > or < to VMUT.
2 Press the Menu Select button directly below VMUT.
3 The display momentarily shows VOICE MUTE OFF, and a
short tone sounds, indicating that the feature is disabled.
OR
The display momentarily shows VOICE MUTE ON, and a
short tone sounds, indicating that the feature is enabled.
 Using the Time-Out Timer
If you attempt to do so, the radio automatically stops your
transmission, and you hear a talk-prohibit tone.
The timer is defaulted at 60 seconds, but it can be
preprogrammed from 3 to 120 seconds, in 15-second intervals,
or it can be disabled entirely for each radio mode, by a qualified
radio technician.
Note:
You will hear a brief, low-pitched, warning tone four
seconds before the transmission times out.
Procedure:
1 Hold down the PTT button longer than the preprogrammed
time. You hear a short, low-pitched warning tone, the
transmission is cut-off, and the LEDs goes out until you
release the PTT button.
Features
This feature filters out unwanted calls with low signal strength or
channels that have a higher than normal background noise.
1 Procedure:
> or < to SQL.
2 Press the Menu Select button directly below SQL.
The display shows SQUELCH XX, where XX is the value for
the current squelch.
3 Press the Menu Select button directly below “+” to increase
the squelch volume.
OR
Press the Menu Select button directly below “-” to decrease
the squelch volume.
Advanced Features
This feature turns off your radio’s transmitter. You cannot
transmit longer than the preset timer setting.
 Using the Conventional Squelch Operation
4 Press H to return to the selected channel.
2 Release the PTT button. The LEDs relight and the timer
resets.
3 Press the PTT button to re-transmit. The time-out timer
restarts and the red LED lights up.
91
English
 Analog Options
 Using the PL Defeat Feature
Tone Private Line (PL), Digital Private-Line (DPL), and carrier
squelch can be available (preprogrammed) per channel.
This feature allows you to override any coded squelch (DPL or
PL) that might be preprogrammed to a channel. The radio will
also unmute to any digital activity on a digital channel.
Option
Result
Carrier squelch (C) You hear all traffic on a channel.
PL or DPL
The radio responds only to your
messages.
Advanced Features
 Digital Options
Note:
One or more of the following options may be preprogrammed in
your radio. Consult your dealer or system administrator for more
information.
Option
Result
Digital CarrierOperated
Squelch (COS)
You hear any digital traffic.
Normal Squelch
You hear any digital traffic having the
correct network access code.
Selective Switch
You hear any digital traffic having the
correct network access code and correct
talkgroup.
92
English
Procedure:
Place the preprogrammed PL Defeat switch in the PL Defeat
position. You hear any activity on the channel.
OR
The radio is muted if no activity is present.
When this feature is active, the Carrier Squelch status
indicator is displayed.
 Using the Digital PTT ID Feature
This feature allows you to the radio ID (number) of the radio
from whom you are currently receiving a transmission. This ID,
consisting up to a maximum of eight characters, can be viewed
by both the receiving radio and the dispatcher.
Your radio’s ID number is also automatically sent every time the
PTT button is pressed. This is a per-channel feature. For digital
voice transmissions, your radio’s ID is sent continuously during
the voice message.
 Accessing General Radio Information
Smart PTT is a per-personality, programmable feature used in
conventional radio systems to keep radio users from talking
over other radio conversations.
Your radio contains information on the following:
When smart PTT is enabled in your radio, you cannot transmit
on an active channel.
• IP Display
If you try to transmit on an active smart-PTT channel, you hear
an alert tone, and the transmission is inhibited. The LED lights
up solid yellow to indicate that the channel is busy.
Note:
• Radio Information
• Control Assignments
Three variations of smart PTT are available:
Mode
Description
Transmit Inhibit on
Busy Channel with
Carrier
You cannot transmit if any traffic is
detected on the channel.
Transmit Inhibit on
Busy Channel with
Wrong Squelch
Code
You cannot transmit on an active channel
with a squelch code or (if secureequipped) encryption key other than your
own. If the PL code is the same as yours,
the transmission is not prevented.
Quick-Key Override This feature can work in conjunction with
either of the two above variations. You
can override the transmit-inhibit state by
quick-keying the radio. In other words, two
PTT button presses within the
preprogrammed time limit.
If the feature inactivity timer is enabled, your radio
automatically exits the feature when your radio is left
idle long enough for the time to expire. You will hear
the Menu Inactive Exit Tone upon feature exit.
 Accessing Radio Information
Advanced Features
 Using the Smart PTT Feature (Conventional Only)
This feature displays the following information of your radio:
• Host Version
• KG (Secure Algorithm)
• Model Number
• Memory Size
• Serial Number
• Tuning Version
• ESN
• Processor Version
• Flash Code
• RF Band
• Flash Size
• Secure Version
• CH 1 – 4 Version
• DSP Version
(depending on the number
of channel connected)
• CHIB Version
93
English
• AUX CH Version
• Siren Version
• MCHB Version
Note:
Press H at any time to return to the Home screen.
 Viewing IP Information
This feature displays the device name, IP address, and status of
your radio.
Note:
Procedure:
1 > or < to INFO.
2 Press the Menu Select button directly below INFO.
Procedure:
3 > or < to RADIO INFO and press the Menu Select button
Press the preprogrammed Info button and proceed to Step 3.
OR
Follow the procedure below.
directly below SEL.
Advanced Features
The device name of your radio is preprogrammed.
Check with your dealer or system administrator for
more information.
4 The display shows the Information screen.
1 > or < to INFO.
5 > or < to scroll through the various information.
2 Press the Menu Select button directly below INFO.
OR
Press the Menu Select button directly below BACK to return
to previous screen.
OR
Press H to exit and return to the home display.
94
English
3 > or < to IP INFO and press the Menu Select button directly
below SEL.
4 > or < to scroll through the various information.
OR
Press the Menu Select button directly below BACK to return
to previous screen.
OR
Press H to exit and return to the Home display.
 Optional External Alarms (Horn and Lights)
This feature displays the programmable radio functions
assigned to the controls of your radio for the currently selected
channel.
All control heads can be equipped for external alarms (horn and
lights) that are activated when a Call Alert page, Private
Conversation call, or phone call is received.
See Programmable Features on page 6 for more information
on the various programmable features of your radio.
The radio always powers up with the horn and lights feature
enabled.
Procedure:
Note:
1 > or < to INFO.
The horn and lights feature must be enabled by a
qualified radio technician.
2 Press the Menu Select button directly below INFO.
 Non-Permanent Horn and Lights
3 > or < to CONTROL MAP and press the Menu Select button
Procedure:
directly below SEL.
4 > or < to scroll through the various information.
OR
Press the Menu Select button directly below BACK to return
to previous screen.
OR
Press H to exit and return to the Home display.
1 Press the Menu Select button directly below H/L
Advanced Features
 Viewing Control Assignments
momentarily. The last selected alarm(s) are enabled, and
the display shows the enabled alarm(s) alternating with the
selected mode, until it is turned off.
2 Press the Menu Select button directly below H/L
momentarily to turn off the alarm(s). The display shows
HORN/LITES OFF.
95
English
 Permanent Horn and Lights
 Changing the Selected Alarms
If Permanent Horn and Lights is enabled, horn and lights will
automatically be turned on when the radio powers up.
Procedure:
Procedure:
1 Press the Menu Select button directly below H/L once to
turn off the alarm(s).
2 Press the Menu Select button directly below H/L
momentarily to enable the last selected alarm(s).
The display briefly shows the enabled alarms, and then
reverts back to the selected mode.
1 Press the Menu Select button directly below H/L until the
display shows the required alarm.
2 Press the Menu Select button directly below the required
entry and the display exits to Home screen.
Press the Menu Select button directly below the entry activates
the option. Below are the selections available.
• Select H+L to turn on both horn and lights. The display shows
HORN/LITES ON.
Advanced Features
• Select LGTS to turn on the lights. The display shows LIGHTS
96
English
ON.
• Select HORN to turn on the horn. The display shows HORN
ON.
An OFF entry is shown at the softkey when one of the features
above is active. Selecting the OFF deactivates the current active
alarm.
 Turning Off Rearmable External Alarms
When you receive a call with the Alarms turned on:
Procedure:
Procedure:
1 Press the Menu Select button directly below CALL, PAGE
1 You hear the vehicle’s horn sounds for four seconds, and/or
the car lights turn on for 60 seconds.
2 The display shows the type of call received (CALL, PAGE,
or PHONE) and the selected mode name.
The time interval can be modified by a qualified radio
technician.
 Turning Off Non-Rearmable External Alarms
Procedure:
1 Press the Menu Select button directly below CALL, PAGE
or PHON will turn off the external alarm(s) and place you
directly in that feature.
OR
Press the PTT button or any control-head button to turn off
the external alarm(s).
2 Press the Menu Select button directly below H/L
or PHON to turn off the external alarm(s) and place you
directly in that feature.
The external alarm(s) is turned off and automatically
rearmed so that when you exit the entry, the external
alarm(s) will automatically turn on.
OR
Press the PTT button or any control head button other than
the Menu Select button directly below H/L to turn off the
external alarm(s).
The external alarm(s) is turned off and automatically
rearmed so that when you exit the entry, the external
alarm(s) will automatically turn on.
OR
Press the Menu Select button directly below H/L to turn off
the external alarm(s) and exit the Horn and Lights feature.
Press the Menu Select button directly below H/L
momentarily to rearm the horn and lights feature.
Advanced Features
 Receiving a Call While Alarms are Turned On
The Volume knob and the DIM button have no effect on the
state of the external alarms.
momentarily to rearm the horn and lights feature.
The Volume Knob and the DIM button have no effect on the
state of the external alarm(s).
97
English
 Voice Announcement
This feature enables the radio to audibly indicate the current
feature mode, Zone or Channel the user has just assigned. This
audio indicator can be customized per customer requirements.
This is typically useful when the user is in a difficult condition to
read the content shown on the display.
Each voice announcement is within a limit of three seconds
maximum. As much as 2000 unique voice announcements are
allowed in a radio. The sum total duration for all voice
announcements in a radio shall be no more than 1000 seconds.
Advanced Features
Note:
This feature must be preprogrammed by a qualified
radio technician.
The features which Voice Announcement supports are:
• Zone
Seek advice from your dealer or qualified technician for
the best selections for this feature.
The two options of priority for the Voice Announcement
available are:
• High – enables the voice of the feature to announce even
when the radio is receiving calls.
• Low – disables the voice of the feature from announcing
when the radio is receiving calls.
Procedure:
You hear a voice announcement when the features below are
preprogrammed in the radio.
• The radio powers up. The radio announces the current zone
and channel it is transmiting.
• Press the preprogrammed voice announcement button
• Channel
• Scan
• Monitor
• Talkaround/Direct
(which specifically programmed to playback the current zone
and channel). The radio announces the current zone and
channel it is transmitting.
Note:
Pressing this preprogrammed playback button will
always enable the voice feature to announce in High
priority.
• Tx Inhibit
Note:
Voice announcements support certain number of zonechannel, but not all.
All the three programmable buttons at the side of the
radio support this feature.
• Change to a new zone. The radio announces the current
98
English
zone and channel it is transmiting.
• Change to a new channel remaining within the current zone.
The radio announces the current channel.
button of the radio to launch or terminate Scan, Monitor,
Talkaround/Direct or Transmit Inhibit. The radio announces
the corresponding feature activation or deactivation.
The following are suggestions to assist you in troubleshooting
possible operating problems.
Caution
The cables that connect to the rear of the radio
could have live voltage on some of their pins. Do
not remove or reconnect these cables. Only a
qualified radio technician should perform this task.
Service performed by unauthorized personnel may
cause the radio to transmit an emergency alarm
even if the unit is turned off.
If your radio is locked up or the display shows FAIL 01/09, turn
the radio off and then back on. If this does not correct the
condition, take the radio to a qualified radio technician for
service.
Advanced Features
• Press either the Menu Select button or preprogrammed
Helpful Tips
If radio operation is intermittent, check with other persons using
the system for similar problems before taking the radio in for
service. Similar problems indicate a system malfunction rather
than a radio failure.
If symptoms persist or, if your unit exhibits other problems,
contact a qualified radio technician.
99
English
Accessories
Your radio is compatible with the accessories listed in this
chapter. Contact your dealer for details.
Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 100
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 101
Control Station. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 101
Footswitches and PTTs . . . . . . . . . . . . . . . . . . . . . . . page 102
Direct Entry Keypad and Siren . . . . . . . . . . . . . . . . . page 102
Microphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 103
Motorcycle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 103
Mounting Solution . . . . . . . . . . . . . . . . . . . . . . . . . . . page 104
Power/CAN Cables . . . . . . . . . . . . . . . . . . . . . . . . . . page 104
Programming/Accessory Cables. . . . . . . . . . . . . . . . page 105
Antennas
• Roof Top, 1/4 Wave 136 – 144 MHz (HAD4006_)
• Roof Top, 1/4 Wave 144 – 152 MHz (HAD4007_)
• Roof Top, 1/4 Wave, 152 – 162 MHz (HAD4008_)
• Roof Top, 1/4 Wave, 162 – 174 MHz (HAD4009_)
• Roof Mount Wideband VHF 136/162 (HAD4016_)
• Roof Mount Wideband VHF 146/174 (HAD4017_)
• VHF Wideband 136 – 174 MHz (HAD4021_)
• 3 dB Low-Profile 762 – 870 MHz (HAF4013_)
• 3 dB Elevated Feed 762 – 870 MHz (HAF4014_)
• 3 dB Motorcycle 762 – 870 MHz (HAF4015_)
Accessories
• 1/4 Wave 762 – 870 MHz (HAF4016_)
• 3 dB Co-Linear 762 – 870 MHz (HAF4017_)
• 3 dB Low Profile Motorcycle 762 – 870 MHz (HAF4018_)
• GPS Antenna Roof Mount (HAG4000_)
• GPS Antenna Motorcycle (HAG4001_)
• GPS Antenna Glass Mount (PMAN4001_)
• 3dB, Roof Mount, 136 – 174 MHz (RAD4010AR_)
100
English
Audio
Control Station
• U.K. Cord (3002120F02)
• Standard Speaker 3.2 Ohm (HSN4032_)
• 110 V Line Cord (3060665A04)
• 7.5 Watt Speaker (Water Resistant) (HSN4038_)
• Europe Cord (3060665A05)
• 13 Watt Speaker (Water Resistant) (HSN4040_)
• Argentina Cord (3085801L01)
• 13 Watt Speaker (Motorcycle) (HSN6003_)
• Desk Tray with Speaker (HLN6042_)
Accessories
• Standard Speaker 8 Ohm (HSN4031_)
• Desk Tray Hardware (HLN7024_)
• Power Supply 15 A Mid Power (HPN4007_)
• Desktop Microphone (RMN5070_)
101
English
Footswitches and PTTs
• PTT Footswitch Button (GLN7278_)
• External Alarm Cable (HKN4258_)
• Emergency Footswitch (HLN5113_)
• Emergency Push Button (HLN5131_)
Direct Entry Keypad and Siren
• Direct Entry Keypad Siren Public Address Deck 8 Button
(H1336_)
• Direct Entry Keypad Status Message Deck 8 Button (H1338_)
• Direct Entry Keypad Status Message Deck 16 Button
(H1339_)
• External Alarm Buzzer 110MA (HLN6953_)
• Fuse Cable (HKN4265_)
• External Alarm Relays (HLN6969_)
• Siren Cable (HKN4363_)
• Accessory PTT (RLN5926_)
• Direct Entry Keypad to O5 Control Head Cable (HKN6189_)
• Mounting Bracket (HKN6938_)
• Auxiliary Switch Panel (HLN1224_)
• Siren (HLN1439_)
Accessories
• Siren Switchbox (HLN6819_)
102
English
• Round Chrome Bull Horn (TDN6251_)
• Rectangular Chrome Bull Horn (TDN6252_)
• Underhood-Grey Bull Horn (TDN6253_)
• Round-Grey Bull Horn (TDN6254_)
Microphones
Motorcycle
• Motorcycle Remote Cable (3075217A01)
• Motorcycle Water Resistant Microphone with DB9 Connector
• Motorcycle Power Cable (HKN6032_)
(HMN1079_)
• Water Resistant Microphone (HMN1089_)
• Traditional Palm Microphone (HMN1090_)
• Keypad Microphone (HMN4079_)
• Motorcycle Enclosure, Black, U.S.A. (HLN7021_)
• Motorcycle Water Resistant Microphone with DB9 Connector
(HMN1079_)
• Motorcycle Waterproof Speaker (HSN6003_)
Accessories
• HandSet/Hangup Armored Cable (HKN1018_)
• Keypad Handset (HMN4097_)
• IMPRES™ Visor Microphone (RMN5054_)
• Desktop Microphone (RMN5070_)
103
English
Mounting Solution
Power/CAN Cables
• Remote Control Head Trunnion (HKN6186_)
• 10' Power Cable Dash Mount (HKN4191_)
• High Power Quick Release Trunnion with Lock (HLN7003_)
• 20' Power Cable Mid Power Remote Mount (HKN4192_)
• Mid Power Key Lock (HLN6372_)
• Motorcycle Power Cable (HKN6032_)
• Mid Power Trunnion (HLN7002_)
• 100W Power Cable (HKN6110_)
• 131' CAN Cable Remote Mount (HKN6164_)
• 115' CAN Cable Remote Mount (HKN6165_)
• 75' CAN Cable Remote Mount (HKN6166_)
• 50' CAN Cable Remote Mount (HKN6167_)
• 30' CAN Cable Remote Mount (HKN6168_)
• 17' CAN Cable Remote Mount (HKN6169_)
Accessories
• 10' CAN Cable Remote Mount (HKN6170_)
104
English
• Accessory Connector for Speaker and Ignition (HLN6863_)
Programming/Accessory Cables
• RS232 Cable Kit 6' Dash Mount (HKN6160_)
• RS232 Cable Kit 20' Remote Mid Power (HKN6161_)
• USB Cable, MAP Connector (6 ft) (HKN6163_)
• USB Cable, MAP Connector (15 ft) (HKN6172_)
Accessories
• Remote Mount RS232 Cable (HKN6122_)
• Keyloader Adaptor MMP/Hirose 1.5” Cable (HKN6182_)
• RS232 MMP Cable (HKN6183_)
• USB MMP Programming Cable (HKN6184_)
• Remote Control Head Power, Speaker, Audio Headset Jacks
(HKN6187_)
• Remote Control Head Power and Speaker (HKN6188_)
• Remote Control Head VIP Connector (HKN6196_)
• Ignition Sense Cable, Dash Mount (HLN6863_)
• Remote Control Head MAP Connector (HLN6961_)
• Standard Microphone Extension Cable (PMKN4033_)
• Keyload Cable KVL3000 Plus to Hirose (TKN8531_)
105
English
Appendix: Maritime Radio Use in the VHF
“WE ARE LOCATED AT _______________________.”
State the position of the vessel in distress, using any
information that will help responders to locate you, e.g.:
• latitude and longitude
• bearing (state whether you are using true or magnetic
north)
• distance to a well-known landmark
• vessel course, speed or destination
State the nature of the distress.
Specify what kind of assistance you need.
State the number of persons on board and the number
needing medical attention, if any.
Mention any other information that would be helpful to
responders, such as type of vessel, vessel length and/or
tonnage, hull color, etc.
“OVER.”
Appendix: Maritime Radio Use in the
VHF Frequency Range
Take a moment to review the following:
Special Channel Assignments. . . . . . . . . . . . . . . . . . page 106
Operating Frequency Requirements . . . . . . . . . . . . . page 107
Special Channel Assignments
 Emergency Channel
If you are in imminent and grave danger at sea and require
emergency assistance, use VHF Channel 16 to send a distress
call to nearby vessels and the United States Coast Guard.
Transmit the following information, in this order:
“MAYDAY, MAYDAY, MAYDAY.”
“THIS IS _____________________, CALL SIGN
__________.”
State the name of the vessel in distress 3 times, followed by
the call sign or other identification of the vessel, stated 3
times.
Repeat “MAYDAY” and the name of the vessel.
106
English
10 Wait for a response.
11 If you do not receive an immediate response, remain by the
radio and repeat the transmission at intervals until you
receive a response. Be prepared to follow any instructions
given to you.
 Non-Commercial Call Channel
For non-commercial transmissions, such as fishing reports,
rendezvous arrangements, repair scheduling, or berthing
information, use VHF Channel 9.
Operating Frequency Requirements
•
on ships subject to Part II of Title III of the Communications
Act, the radio must be capable of operating on the 156.800
MHz frequency
•
on ships subject to the Safety Convention, the radio
must be capable of operating:
•
in the simplex mode on the ship station transmitting
frequencies specified in the 156.025 – 157.425 MHz
frequency band, and
• in the semiduplex mode on the two frequency channels
specified in the table below.
Note:
Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83
cannot be lawfully used by the general public in US
waters.
Additional information about operating requirements in the
Maritime Services can be obtained from the full text of FCC
Rule Part 80 and from the US Coast Guard.
Table A-1: VHF Marine Channel List
Frequency (MHz)
Channel
Number
Transmit
Receive
156.050
160.650
Frequency (MHz)
Channel
Number
Transmit
Receive
10
11
12
13**
14
15**
16
17**
18
19
20
22
156.100
156.150
156.200
156.250
156.300
156.350
156.400
156.450
156.500
156.550
156.600
156.650
156.700
156.750
156.800
156.850
156.900
156.950
157.000
157.050
157.100
157.150
160.700
160.750
160.800
160.850
–
160.950
–
156.450
156.500
156.550
156.600
156.650
156.700
156.750
156.800
156.850
161.500
161.550
161.600
161.650
161.700
161.750
Appendix: Maritime Radio Use in the VHF
A radio designated for shipboard use must comply with Federal
Communications Commission Rule Part 80 as follows:
Table A-1: VHF Marine Channel List (Continued)
107
English
Appendix: Maritime Radio Use in the VHF
Table A-1: VHF Marine Channel List (Continued)
Frequency (MHz)
Channel
Number
Transmit
Receive
24
25
26
27
28
60
62
63
65
66
67**
68
69
71
72
73
74
75
76
77**
157.200
157.250
157.300
157.350
157.400
156.025
156.075
156.125
156.175
156.225
156.275
156.325
156.375
156.425
156.475
156.575
156.625
156.675
156.725
***
***
156.875
161.800
161.850
161.900
161.950
162.000
160.625
160.675
160.725
160.775
160.825
160.875
160.925
156.375
156.425
156.475
156.575
–
156.675
156.725
***
***
–
108
English
Table A-1: VHF Marine Channel List (Continued)
Frequency (MHz)
Channel
Number
Transmit
Receive
78
79
80
84
85
86
87
88
156.925
156.975
157.025
157.075
157.125
157.175
157.225
157.275
157.325
157.375
157.425
161.525
161.575
161.625
161.675
161.725
161.775
161.825
161.875
161.925
161.975
162.025
* Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be
lawfully used by the general public in US waters.
** Low power (1 W) only
*** Guard band
Note: A – in the Receive column indicates that the channel is
transmit only.
Term
Glossary
Central
Controller
A software-controlled, computer-driven
device that receives and generates data for
the trunked radios assigned to it. It
monitors and directs the operations of the
trunked repeaters.
Definition
ACK
Acknowledgment of communication.
Active Channel
A channel that has traffic on it.
Analog Signal
An RF signal that has a continuous nature
rather than a pulsed or discrete nature.
ARS
Automatic Registration Service
ASTRO 25
Trunking
Motorola standard for wireless digital
trunked communications.
Channel
ASTRO
Conventional
Motorola standard for wireless digital
conventional communications.
A group of characteristics such as transmit/
receive frequency pairs, radio parameters,
and encryption encoding.
CHIB
Control Head Interface Board
Autoscan
A feature that allows the radio to
automatically scan the members of a scan
list.
AUX CH
Auxiliary Control Head
Call Alert
Privately page an individual by sending an
audible tone.
Glossary
Carrier Squelch
Feature that responds to the presence of
an RF carrier by opening or unmuting
(turning on) a receiver’s audio circuit. A
squelch circuit silences the radio when no
signal is being received so that the user
does not have to listen to “noise”.
This glossary is a list of specialized terms used in this manual.
Term
Definition
In a trunking system, one of the channels
that is used to provide a continuous, twoControl Channel way/data communications path between
the central controller and all radios on the
system.
Conventional
Typically refers to radio-to-radio
communications, sometimes through a
repeater (see Trunking).
Conventional
Scan List
A scan list that includes only conventional
channels.
109
English
Glossary
Term
Definition
Term
Definition
CP
Codeplug
Cursor
A visual tracking marker (a blinking line)
that indicates a location on the display.
Failsoft
Deadlock
Displayed by the radio after three failed
attempts to unlock the radio.The radio must
be powered off and on prior to another
attempt.
A feature that allows communications to
take place even though the central
controller has failed. Each trunked repeater
in the system transmits a data word
informing every radio that the system has
gone into failsoft.
FCC
Federal Communications Commission.
Hang Up
Disconnect.
Home screen
The first display information after the radio
completes its self test.
KVL
Key-variable loader: A device for loading
encryption keys into the radio.
LCD
Liquid crystal display.
LED
Light-emitting diode.
Menu Entry
A software-activated feature shown at the
bottom of the display – selection of these
MCHB
Millennium Control Head Board
Digital Private
Line (DPL)
A type of coded squelch using data bursts.
Similar to PL except a digital code is used
instead of a tone.
Digital Signal
An RF signal that has a pulsed, or discrete,
nature, rather than a continuous nature.
Dispatcher
An individual who has radio system
management duties.
DSP
Digital Signal Processing
Dynamic
Regrouping
A feature that allows the dispatcher to
temporarily reassign selected radios to a
single special channel so they can
communicate with each other.
ESN
Electrical Serial Number
110
English
features is controlled by the g.
Term
Multi-System
Talkgroup Scan
List
Check channel activity through menu
entries. If the channel is clear, you hear
static. If the channel is in use, you hear
conversation. It also serves as a way to
check the volume level of the radio, since
the radio “opens the squelch” when the
monitor button is pressed.
A scan list that can include both talkgroups
(trunked) and channels (conventional).
Network Access Code (NAC) operates on
Network Access digital channels to reduce voice channel
Code
interference between adjacent systems
and sites.
Non-Tactical/
Revert
The user talks on a preprogrammed
emergency channel. The emergency alarm
is sent out on this same channel.
OTAR
Over-the-air rekeying.
Page
A one-way alert, with audio and/or display
messages.
Personality
A set of unique features specific to a radio.
PIN
Personal Identification Number
Preprogrammed
Refers to a software feature that has been
activated by a qualified radio technician.
Term
Definition
Private
(Conversation)
Call
A feature that lets you have a private
conversation with another radio user in the
talkgroup.
Private Line
(PL)
A sub-audible tone that is transmitted such
that only receivers decoding the tone
receives it.
Programmable
Refers to a radio control that can have a
radio feature assigned to it.
PTT
Push-To-Talk – the PTT button engages
the transmitter and puts the radio in
transmit (send) operation when pressed.
Radio
Frequency (RF)
The part of the general frequency spectrum
between the audio and infrared light
regions (about 10 kHz to 10,000,000 MHz).
Repeater
A conventional radio feature, where you
talk through a receive/transmit facility that
re-transmits received signals, in order to
improve communications range and
coverage.
Selective Call
A feature that allows you to call a select
individual, intended to provide privacy and
to eliminate the annoyance of having to
listen to conversations of no interest to you.
Glossary
Monitor
Definition
111
English
Term
Definition
Glossary
Any digital P25 traffic having the correct
Selective Switch Network Access Code and the correct
talkgroup.
Squelch
Special electronic circuitry, added to the
receiver of a radio, that reduces, or cuts off,
unwanted signals before they are heard in
the speaker.
Standby
An operating condition whereby the radio’s
speaker is muted but still continues to
receive data.
Status Calls
Pre-defined text messages that allow the
user to send a conditional message without
talking.
Tactical/
Non-Revert
The user talks on the channel that was
selected before the radio entered the
emergency state.
Talkaround
Bypass a repeater and talk directly to
another unit for easy local unit-to-unit
communications.
Talkgroup
An organization or group of radio users
who communicate with each other using
the same communication path.
TMS
Text Messaging Service
112
English
Term
Definition
Trunking
The automatic sharing of communications
paths between a large number of users
(see Conventional).
Trunking
Priority Monitor
Scan List
A scan list that includes talkgroups that are
all from the same trunking system.
USK
Unique Shadow Key.
UTC
Coordinated Universal Time. The
international time standard (formerly
Greenwich Mean Time, or GMT). Zero
hours UTC is midnight in Greenwich,
England, which is located at 0 degrees
longitude. Everything east of Greenwich
(up to 180 degrees) is later in time;
everything west is earlier. There are 42
time authorities around the world that are
constantly synchronizing with each other.
Abbreviated as UTC (English backronym =
Universal Time, Coordinated), it is also
known as Zulu (Z) Time.
Zone
A grouping of channels.
Commercial Warranty and Service
MOTOROLA COMMUNICATION PRODUCTS
I. WHAT THIS WARRANTY COVERS AND FOR HOW
LONG:
MOTOROLA INC. (“MOTOROLA”) warrants the MOTOROLA
manufactured Communication Products listed below (“Product”)
against defects in material and workmanship under normal use and
service for a period of time from the date of purchase as scheduled
below:
MOTOROLA cannot be responsible in any way for any ancillary
equipment not furnished by MOTOROLA which is attached to or
used in connection with the Product, or for operation of the Product
with any ancillary equipment, and all such equipment is expressly
excluded from this warranty. Because each system which may use
the Product is unique, MOTOROLA disclaims liability for range,
coverage, or operation of the system as a whole under this
warranty.
II. GENERAL PROVISIONS:
APX 7500 O5 Control Head
One (1) Year
Product Accessories
One (1) Year
MOTOROLA, at its option, will at no charge either repair the
Product (with new or reconditioned parts), replace it (with a new or
reconditioned Product), or refund the purchase price of the Product
during the warranty period provided it is returned in accordance
with the terms of this warranty. Replaced parts or boards are
warranted for the balance of the original applicable warranty period.
All replaced parts of Product shall become the property of
MOTOROLA.
This express limited warranty is extended by MOTOROLA to the
original end user purchaser only and is not assignable or
transferable to any other party. This is the complete warranty for the
This warranty sets forth the full extent of MOTOROLA'S
responsibilities regarding the Product. Repair, replacement or
refund of the purchase price, at MOTOROLA’s option, is the
exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL
OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES,
INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED
WARRANTY. IN NO EVENT SHALL MOTOROLA BE LIABLE FOR
DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE
PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME,
INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR
SAVINGS OR OTHER INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
Commercial Warranty and Service
Limited Warranty
Product manufactured by MOTOROLA. MOTOROLA assumes no
obligations or liability for additions or modifications to this warranty
unless made in writing and signed by an officer of MOTOROLA.
Unless made in a separate agreement between MOTOROLA and
the original end user purchaser, MOTOROLA does not warrant the
installation, maintenance or service of the Product.
113
English
INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT
SUCH MAY BE DISCLAIMED BY LAW.
Commercial Warranty and Service
III. STATE LAW RIGHTS:
SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES
OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY
NOT APPLY.
This warranty gives specific legal rights, and there may be other
rights which may vary from state to state.
IV. HOW TO GET WARRANTY SERVICE:
You must provide proof of purchase (bearing the date of purchase
and Product item serial number) in order to receive warranty
service and, also, deliver or send the Product item, transportation
and insurance prepaid, to an authorized warranty service location.
Warranty service will be provided by MOTOROLA through one of its
authorized warranty service locations. If you first contact the
company which sold you the Product (e.g., dealer or
communication service provider), it can facilitate your obtaining
warranty service. You can also call MOTOROLA at 1-800-927-2744
US/Canada.
V. WHAT THIS WARRANTY DOES NOT COVER:
A) Defects or damage resulting from use of the Product in other
than its normal and customary manner.
B) Defects or damage from misuse, accident, water, or neglect.
114
English
C)Defects or damage from improper testing, operation,
maintenance, installation, alteration, modification, or adjustment.
D)Breakage or damage to antennas unless caused directly by
defects in material workmanship.
E) A Product subjected to unauthorized Product modifications,
disassembles or repairs (including, without limitation, the addition
to the Product of non-MOTOROLA supplied equipment) which
adversely affect performance of the Product or interfere with
MOTOROLA's normal warranty inspection and testing of the
Product to verify any warranty claim.
F) Product which has had the serial number removed or made
illegible.
G)Rechargeable batteries if:
• any of the seals on the battery enclosure of cells are broken or
show evidence of tampering.
• the damage or defect is caused by charging or using the battery
in equipment or service other than the Product for which it is
specified.
H)Freight costs to the repair depot.
I) A Product which, due to illegal or unauthorized alteration of the
software/firmware in the Product, does not function in
accordance with MOTOROLA’s published specifications or the
FCC type acceptance labeling in effect for the Product at the time
the Product was initially distributed from MOTOROLA.
J) Scratches or other cosmetic damage to Product surfaces that
does not affect the operation of the Product.
K) Normal and customary wear and tear.
VI. PATENT AND SOFTWARE PROVISIONS:
Laws in the United States and other countries preserve for
MOTOROLA certain exclusive rights for copyrighted MOTOROLA
software such as the exclusive rights to reproduce in copies and
distribute copies of such MOTOROLA software. MOTOROLA
software may be used in only the Product in which the software was
originally embodied and such software in such Product may not be
replaced, copied, distributed, modified in any way, or used to
produce any derivative thereof. No other use including, without
limitation, alteration, modification, reproduction, distribution, or
reverse engineering of such MOTOROLA software or exercise of
rights in such MOTOROLA software is permitted. No license is
granted by implication, estoppel or otherwise under MOTOROLA
patent rights or copyrights.
VII. GOVERNING LAW:
Commercial Warranty and Service
MOTOROLA will defend, at its own expense, any suit brought
against the end user purchaser to the extent that it is based on a
claim that the Product or parts infringe a United States patent, and
MOTOROLA will pay those costs and damages finally awarded
against the end user purchaser in any such suit which are
attributable to any such claim, but such defense and payments are
conditioned on the following:
A) that MOTOROLA will be notified promptly in writing by such
purchaser of any notice of such claim;
B) that MOTOROLA will have sole control of the defense of such
suit and all negotiations for its settlement or compromise; and
C)should the Product or parts become, or in MOTOROLA’s opinion
be likely to become, the subject of a claim of infringement of a
United States patent, that such purchaser will permit
MOTOROLA, at its option and expense, either to procure for
such purchaser the right to continue using the Product or parts or
to replace or modify the same so that it becomes non-infringing
or to grant such purchaser a credit for the Product or parts as
depreciated and accept its return. The depreciation will be an
equal amount per year over the lifetime of the Product or parts as
established by MOTOROLA.
MOTOROLA will have no liability with respect to any claim of patent
infringement which is based upon the combination of the Product or
parts furnished hereunder with software, apparatus or devices not
furnished by MOTOROLA, nor will MOTOROLA have any liability
for the use of ancillary equipment or software not furnished by
MOTOROLA which is attached to or used in connection with the
Product. The foregoing states the entire liability of MOTOROLA with
respect to infringement of patents by the Product or any parts
thereof.
This Warranty is governed by the laws of the State of Illinois, U.S.A.
115
English
Commercial Warranty and Service
SERVICE
Proper repair and maintenance procedures will assure efficient
operation and long life for this product. A Motorola maintenance
agreement will provide expert service to keep this and all other
communication equipment in perfect operating condition. A
nationwide service organization is provided by Motorola to support
maintenance services. Through its maintenance and installation
program, Motorola makes available the finest service to those
desiring reliable, continuous communications on a contract basis.
For a contract service agreement, please contact your nearest
Motorola service or sales representative, or an authorized Motorola
dealer.
Express Service Plus (ESP) is an optional extended service
coverage plan, which provides for the repair of this product for a
period of three years from the date of shipment from the factory, or
the date of delivery if purchased from an authorized Motorola twoway radio dealer. For more information about ESP, contact the
Motorola Radio Support Center, 2204 Galvin Drive, Elgin, IL 60123,
1-800-227-6772.
116
English
Motorola, Inc.
1301 E. Algonquin Rd.
Schaumburg, IL 60196-1078, U.S.A.
MOTOROLA and the Stylized M Logo are registered
in the U.S. Patent and Trademark Office.
All other product or service names are the property of
their respective owners.
© 2009 by Motorola, Inc.
All rights reserved. Printed in the U.S.A.
September 2009
RO-1-2005
*6875947M01*
6875947M01-A

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Mode                       : UseOutlines
XMP Toolkit                     : 3.1-702
Producer                        : Acrobat Distiller 7.0 (Windows)
Create Date                     : 2009:10:13 09:37:33Z
Creator Tool                    : FrameMaker 8.0
Modify Date                     : 2009:11:06 14:25:24-05:00
Metadata Date                   : 2009:11:06 14:25:24-05:00
Format                          : application/pdf
Title                           : APX 7500 05 UG
Creator                         : Penang GCD
Document ID                     : uuid:ed3df384-23f4-430a-b7f6-e81aaafbd1d8
Instance ID                     : uuid:b2797d51-274e-4c82-9df2-8a1efbab8d30
Has XFA                         : No
Page Count                      : 132
Author                          : Penang GCD
EXIF Metadata provided by EXIF.tools
FCC ID Filing: AZ492FT7037

Navigation menu