Motorola Solutions 92FT7048 UHF1_7/800 MHz Mobile Radio User Manual APX Mobile User Guide O5 Control Head

Motorola Solutions, Inc. UHF1_7/800 MHz Mobile Radio APX Mobile User Guide O5 Control Head

Contents

Ex 8b Users Manual

mAPX O5 Control HeadMobile Radio User GuideO5Head_6875947M01_C.book Page 1 Wednesday, October 20, 2010 12:13 PM
O5Head_6875947M01_C.book Page 2 Wednesday, October 20, 2010 12:13 PM
EnglishmASTRO® APX™ O5 Control Head Mobile RadioQuick Reference CardProduct Safety and RF Exposure ComplianceATTENTION!This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed with your radio (Motorola Publication part number 6881095C99) to ensure compliance with RF energy exposure limits. Radio ControlsRadio On/OffAdjusting VolumeSelecting a ZoneSelecting a ChannelReceiving and TransmittingSending an Emergency AlarmTo exit emergency at any time, press and hold the Emergency button.Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio.!Volume KnobAccessory Port (Microphone)Menu Select ButtonMenu EntriesLED IndicatorsDim ButtonHome ButtonNavigation ButtonPower On/Off ButtonIndicatorsMode KnobOrange Button _______Press the Power On/Off button to toggle the power on or off. Turn the Volume Knob clockwise to increase volume or counterclockwise to decrease the volume. 1> or < to ZONE. 2> or < button until the desired zone is displayed.3Press H or the PTT button to confirm the selected zone number.4Press the PTT button to begin transmitting on the displayed zone channel.1Press and hold > to scroll to CHAN and press the Menu Select button directly below CHAN. The display shows the current zone and channel.2Rotate the Mode knob to the desired channel.3Press H or the PTT button to confirm the channel. 4Press the PTT button to transmit on the displayed zone channel. 1Take the microphone off hook. 2Select zone/channel.3Listen for a transmission. ORTurn the Volume Knob.OR> or < to MON then press the Menu Select button directly below MON and listen for activity.4Adjust volume, if necessary.5Press the PTT button to transmit; release to receive.1Press the Emergency button. A tone sounds and the display alternates EMERGENCY and the home display.2A dispatcher acknowledgment ACK RECEIVED display follows.AND, Trunking Only:A high-pitched tone indicates that the alarm has been received by the trunked system’s central controller.3Press and hold the emergency button or the PTT button to return to normal operation.*PMLN5592B*PMLN5592B© 2009, 2010 by Motorola, Inc. All Rights Reserved. 10/101301 E. Algonquin Rd., Schaumburg,IL 60196-1078, U.S.A.O5Head_6875947M01_C.book Page 3 Wednesday, October 20, 2010 12:13 PM
EnglishSending an Emergency Call (Trunking Only)To exit emergency at any time, press and hold the Emergency button.Sending a Silent Emergency AlarmIf silent emergency alarm is used with emergency call, pressing the PTT button exits the silent mode and initiates the emergency call.Display Status Icons1Press Emergency button. 2A tone sounds and the display alternates EMERGENCY and the home display.ORA talk prohibited tone sounds when the selected channel does not support emergency.3Press and hold the PTT button. Speak clearly into the microphone.4Release the PTT to end the transmission. 1Press the preprogrammed Emergency button to activate the silent alarm feature. 2The display does not change; the LED does not light up, and there is no tone.Receiving a call or data.Transmitting a call or data.Received an Individual Call.The more stripes, the stronger the signal strength for the current site (trunking only).utFVDirect radio-to-radio communication or communication through a repeater.On = DirectOff = RepeaterThis channel is being monitored.Voice muting the affiliated trunking talkgroup or selected conventional channel.On = EnabledOff = DisabledL = Radio is set at Low power.H = Radio is set at High power.Scanning a scan list.Blinking dot = Detects activity on the Priority-One Channel during scan.Steady dot = Detects activity on the Priority-Two Channel during scan.Radio is in the view or program mode.On steady = View mode.Blinking = Program mode.OMKHOR .ijThe vote scan feature is enabled.On = Secure operation.Off = Clear operation.Blinking = Receiving an encrypted voice call.On = AES Secure operation.Off = Clear operation.Blinking = Receiving an encrypted voice call.On = Location feature enabled, and location signal available.Off = Location feature disabled.Blinking = Location feature enabled, but location signal unavailable.On = User is currently associated with the radio.Off = User is currently not associated with the radio.Blinking = Device registration or user registration with the server failed due to an invalid username or pin.Data activity is present.kmlGnoMenu Navigation< or > to Menu Entry.g directly below Menu Entry to select.H to exit.< or > to scroll through sub-list.g directly below Menu Entry to select.O5Head_6875947M01_C.book Page 4 Wednesday, October 20, 2010 12:13 PM
Declaration of ConformityEnglishiDeclaration of ConformityThis declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below.DECLARATION OF CONFORMITYPer FCC CFR 47 Part 2 Section 2.1077(a)Responsible Party Name: Motorola, Inc.Address: Motorola, Inc. 1301 E. Algonquin Rd.Schaumburg, IL60196-1078, U.S.A.Phone Number: 1-800-927-2744Hereby declares that the product:Model Name: APX 7500 / APX 6500conforms to the following regulations:FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a)Class B Digital DeviceAs a personal computer peripheral, this device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.O5Head_6875947M01_C.book Page i Wednesday, October 20, 2010 12:13 PM
Declaration of ConformityEnglishiiNote:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.O5Head_6875947M01_C.book Page ii Wednesday, October 20, 2010 12:13 PM
ContentsEnglishiiiContentsThis User Guide contains all the information you need to use the APX™ Mobile Radios.Declaration of Conformity . . . . . . . . . . . . . . . . . .iImportant Safety Information . . . . . . . . . . . . . .ixProduct Safety and RF Exposure Compliance . . . . ixSoftware Version . . . . . . . . . . . . . . . . . . . . . . . .ixComputer Software Copyrights . . . . . . . . . . . . xDocumentation Copyrights . . . . . . . . . . . . . . . . xDisclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xGetting Started . . . . . . . . . . . . . . . . . . . . . . . . . . 1How to Use This User Guide . . . . . . . . . . . . . . . . . . 1Notations Used in This Manual . . . . . . . . . . . . . . . . . 1Additional Performance Enhancement . . . . . . . . . . . 2Dynamic System Resilience (DSR) . . . . . . . . . . . . . .2CrossTalk Prevention . . . . . . . . . . . . . . . . . . . . . . . .2Encrypted Integrated Data (EID) . . . . . . . . . . . . . . . .2SecureNet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2What Your Dealer/System Administrator Can Tell You . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Preparing Your Radio for Use . . . . . . . . . . . . . .3Turning On the Radio . . . . . . . . . . . . . . . . . . . . . . . . 4Validating Compatibility During Power Up . . . . . . . . 4Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . 5Identifying Radio Controls . . . . . . . . . . . . . . . . .5Radio Parts and Controls . . . . . . . . . . . . . . . . . . . . . 6 O5 Control Head and Microphone . . . . . . . . . . . . . 6Programmable Features . . . . . . . . . . . . . . . . . . . . . . 7Assignable Radio Functions . . . . . . . . . . . . . . . . . . 7Assignable Settings or Utility Functions . . . . . . . . . . 9Accessing the Preprogrammed Functions . . . . . . . . 9Using the Menu Select Buttons . . . . . . . . . . . . . . . . 9Using the Advance Programmable Buttons . . . . . . 10Using the Navigation Buttons . . . . . . . . . . . . . . . . 10Home Button . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Data Feature Button . . . . . . . . . . . . . . . . . . . . . . . 104-Way Navigation Button . . . . . . . . . . . . . . . . . . . 11Volume Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Mode Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Using the Keypad . . . . . . . . . . . . . . . . . . . . . 12O5Head_6875947M01_C.book Page iii Wednesday, October 20, 2010 12:13 PM
ContentsEnglishivKeypad Characters – Uppercase Mode . . . . . . . . . 12Keypad Characters – Lowercase Mode . . . . . . . . . 13Keypad Characters – Numeric Mode . . . . . . . . . . . 14Keypad Characters – Hexadecimal Mode . . . . . . . 15Push-To-Talk (PTT) Button . . . . . . . . . . . . . . . . . 16Identifying Status Indicators . . . . . . . . . . . . . .16Status Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Text Messaging Service (TMS) Icons . . . . . . . . . . 19Status Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19TMS Menu Options . . . . . . . . . . . . . . . . . . . . . . 20LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Intelligent Lighting Indicators . . . . . . . . . . . . . . . 22Alert Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23General Radio Operation . . . . . . . . . . . . . . . . .26Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . 26Selecting a Radio Channel . . . . . . . . . . . . . . . . . . . 27Receiving and Responding to a Radio Call . . . . . . 27Receiving and Responding to a Talkgroup Call . . . 28Receiving and Responding to a Private Call (Trunking Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Receiving and Responding to a Telephone Call . . 29Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . 30Making a Talkgroup Call . . . . . . . . . . . . . . . . . . . . .30Making a Private Call (Trunking Only) . . . . . . . . . . .31Making a Telephone Call . . . . . . . . . . . . . . . . . . . .32Repeater or Direct Operation . . . . . . . . . . . . . . . . . 33Monitoring Features . . . . . . . . . . . . . . . . . . . . . . . . 33Monitoring a Channel . . . . . . . . . . . . . . . . . . . . . . .33Conventional Mode Operation . . . . . . . . . . . . . . . .34Advanced Features . . . . . . . . . . . . . . . . . . . . . 35Advanced Call Features . . . . . . . . . . . . . . . . . . . . . 35Calling a Phone Not in the List . . . . . . . . . . . . . . . .35Receiving and Making a Selective Call (Conventional Only) . . . . . . . . . . . . . . . . . . . . . . . .36Receiving a Selective Call . . . . . . . . . . . . . . . . . . .36Making a Selective Call . . . . . . . . . . . . . . . . . . . . .36Using the Talkgroup Call Feature (Conventional Operation Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . .37Selecting a Talkgroup . . . . . . . . . . . . . . . . . . . . . . .37Sending a Status Call . . . . . . . . . . . . . . . . . . . . . . .38Using the Dynamic Regrouping Feature (Trunking Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . .38Requesting a Reprogram . . . . . . . . . . . . . . . . . . . .39Classifying Regrouped Radios . . . . . . . . . . . . . . . .39Multiple Control Head Features . . . . . . . . . . . . . . . 40Multiple Control Head Features . . . . . . . . . . . . . . .40Setting the Initial Control Head’s ID . . . . . . . . . . . .40O5Head_6875947M01_C.book Page iv Wednesday, October 20, 2010 12:13 PM
ContentsEnglishvAll Active Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .41Intercom Feature in All Active Mode . . . . . . . . . . .41One Active Mode . . . . . . . . . . . . . . . . . . . . . . . . . . .41Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Making a Private Call from Contacts . . . . . . . . . . . .43Adding a New Contact Entry . . . . . . . . . . . . . . . . . .45Deleting a Contact Entry . . . . . . . . . . . . . . . . . . . . .46Adding a Contact to a Call List or Phone List . . . . .46Editing a Contact in a Call List or a Phone List . . . .47Editing an Entry Alias . . . . . . . . . . . . . . . . . . . . . . .47Editing as Entry ID . . . . . . . . . . . . . . . . . . . . . . . . .47Editing a Call Type . . . . . . . . . . . . . . . . . . . . . . . . .48Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Viewing a Scan List . . . . . . . . . . . . . . . . . . . . . . . . .49Editing the Scan List . . . . . . . . . . . . . . . . . . . . . . . .49Changing the Scan List Status . . . . . . . . . . . . . . . .50Viewing and Changing the Priority Status . . . . . . . .50Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Turning Scan On or Off . . . . . . . . . . . . . . . . . . . . . .51Turning Scan On While Disregarding the Squelch Code (Conventional Channels Only) . . . . .51Transmitting While the Scan is On . . . . . . . . . . . . .51Radio Programmed for Talkback Scan . . . . . . . . .51Radio Programmed for Non-Talkback Scan . . . . .52Deleting a Nuisance Channel . . . . . . . . . . . . . . . . .52Restoring a Nuisance Channel . . . . . . . . . . . . . . . .52Changing Priorities Status While Scan is On . . . . . 53Restoring Priorities in a Scan List . . . . . . . . . . . . . 53Hang Up (HUB) . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Call Alert Paging . . . . . . . . . . . . . . . . . . . . . . . . . . 54Receiving a Call Alert Page . . . . . . . . . . . . . . . . . . 54Sending a Call Alert Page . . . . . . . . . . . . . . . . . . . 55In-Call User Alert . . . . . . . . . . . . . . . . . . . . . . . . . . 56Emergency Operation . . . . . . . . . . . . . . . . . . . . . . . 56Sending an Emergency Alarm . . . . . . . . . . . . . . . . 57Sending an Emergency Call (Trunking Only) . . . . 57Sending an Emergency Alarm with Emergency Call . . . . . . . . . . . . . . . . . . . . . . . . . . . 57Sending a Silent Emergency Alarm . . . . . . . . . . . . 58Special Considerations for Emergencies . . . . . . . . 59Automatic Registration Service (ARS) . . . . . . . . . . 60Selecting or Changing ARS Mode . . . . . . . . . . . . . 60Accessing the User Login Feature . . . . . . . . . . . . . 61Logging In as a User . . . . . . . . . . . . . . . . . . . . . . . 61 Logging Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Text Messaging Service (TMS) . . . . . . . . . . . . . . . . 63Accessing TMS Feature . . . . . . . . . . . . . . . . . . . . 63Composing and Sending a New Text Message . . . 64Sending a Quick Text Message . . . . . . . . . . . . . . . 65Using the Priority Status and Request Reply Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67Appending or Removing a Priority Status to a O5Head_6875947M01_C.book Page v Wednesday, October 20, 2010 12:13 PM
ContentsEnglishviText Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67Appending or Removing a Request Reply to a Text Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67Appending a Priority Status and a Reply Request to a Text Message . . . . . . . . . . . . . . . . . . . . . . . . . 67Removing a Priority Status and a Reply Request from a Text Message . . . . . . . . . . . . . . . . . . . . . . . 68Managing Text Messages . . . . . . . . . . . . . . . . . . . 68Receiving a Text Message . . . . . . . . . . . . . . . . . . 68Viewing a Text Message from the Inbox . . . . . . . . 69Replying to a Received Text Message . . . . . . . . . 70Accessing the Drafts Folder . . . . . . . . . . . . . . . . . . 71Managing Sent Text Messages . . . . . . . . . . . . . . . 71Viewing a Sent Text Message . . . . . . . . . . . . . . . . 71Sending a Sent Text Message . . . . . . . . . . . . . . . 72Deleting Text Messages . . . . . . . . . . . . . . . . . . . . 73Secure Operations . . . . . . . . . . . . . . . . . . . . . . . . . 73Managing Encryption . . . . . . . . . . . . . . . . . . . . . . . 73Loading a Single Encryption Key . . . . . . . . . . . . . . 73Loading the Group Encryption Keys . . . . . . . . . . . 74Using the Multikey Feature . . . . . . . . . . . . . . . . . . 74Selecting an Encryption Key (Conventional Only) . 75Enabling Secure Transmission . . . . . . . . . . . . . . . 75Accessing the Secure Feature . . . . . . . . . . . . . . . 75Selecting a Keyset . . . . . . . . . . . . . . . . . . . . . . . . . 76Erasing the Selected Encryption Keys . . . . . . . . . . 76Requesting an Over-the-Air Rekey . . . . . . . . . . . . 77MDC Over-the-Air Rekeying (OTAR) Page . . . . . .77Hear Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78The Global Positioning System (GPS) . . . . . . . . . . 78Understanding the GPS Feature . . . . . . . . . . . . . . .78Enhancing GPS Performance . . . . . . . . . . . . . . . . .79The Outdoor Location Feature (Using GPS) . . . . . .79Accessing the Outdoor Location Feature . . . . . . . .80Saving a Waypoint . . . . . . . . . . . . . . . . . . . . . . . . .81Viewing a Saved Waypoint . . . . . . . . . . . . . . . . . . .82Editing the Alias of a Waypoint . . . . . . . . . . . . . . . .83Editing the Coordinates of a Waypoint . . . . . . . . . .83Deleting a Single Saved Waypoint . . . . . . . . . . . . .84Deleting All Saved Waypoints . . . . . . . . . . . . . . . .85Measuring the Distance and Bearing from a Saved Waypoint . . . . . . . . . . . . . . . . . . . . . . . . . . .85Using the Location Feature While in Emergency Mode . . . . . . . . . . . . . . . . . . . . . . . . . .86Trunking System Controls . . . . . . . . . . . . . . . . . . . 86Using the Failsoft System . . . . . . . . . . . . . . . . . . . .86Going Out-of-Range . . . . . . . . . . . . . . . . . . . . . . . .87SmartZone® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87Using Site Trunking Feature . . . . . . . . . . . . . . . . . .87Locking and Unlocking a Site . . . . . . . . . . . . . . . . .88Viewing and Changing a Site . . . . . . . . . . . . . . . . .88Viewing the Current Site . . . . . . . . . . . . . . . . . . . . .88Changing the Current Site . . . . . . . . . . . . . . . . . . .89Trunked Announcement . . . . . . . . . . . . . . . . . . . . .89O5Head_6875947M01_C.book Page vi Wednesday, October 20, 2010 12:13 PM
ContentsEnglishviiInitiating an Announcement . . . . . . . . . . . . . . . . . .90Ignition Switch Options . . . . . . . . . . . . . . . . . . . . . . 90Blank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90Tx Inhibit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90PTT Tx Inhibit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91Soft Power Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91Ignition Only Power Up . . . . . . . . . . . . . . . . . . . . . .91Emergency Power Up . . . . . . . . . . . . . . . . . . . . . . .91Auto Power Off Timer . . . . . . . . . . . . . . . . . . . . . . .92Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92Viewing Recent Calls List . . . . . . . . . . . . . . . . . . . .92Selecting the Power Level . . . . . . . . . . . . . . . . . . . .93Selecting a Radio Profile . . . . . . . . . . . . . . . . . . . . .93Controlling the Display Backlight . . . . . . . . . . . . . . .94Turning Keypad Tones On or Off . . . . . . . . . . . . . .94Turning Voice Mute On or Off . . . . . . . . . . . . . . . . .95Using the Time-Out Timer . . . . . . . . . . . . . . . . . . . .95Using the Conventional Squelch Operation Features . . . . . . . . . . . . . . . . . . . . . . . . .96Analog Options . . . . . . . . . . . . . . . . . . . . . . . . . . .96Digital Options . . . . . . . . . . . . . . . . . . . . . . . . . . . .96Using the PL Defeat Feature . . . . . . . . . . . . . . . . . .97Using the Digital PTT ID Feature . . . . . . . . . . . . . .97Using the Smart PTT Feature (Conventional Only) 97Accessing General Radio Information . . . . . . . . . . .98Accessing Radio Information . . . . . . . . . . . . . . . . 98Viewing IP Information . . . . . . . . . . . . . . . . . . . . . 99Viewing Control Assignments . . . . . . . . . . . . . . . . 99Using Optional External Alarms (Horn and Lights) . . . . . . . . . . . . . . . . . . . . . . . . . 100Using Non-Permanent Horn and Lights . . . . . . . 100Using Permanent Horn and Lights . . . . . . . . . . . 100Changing the Selected Alarms . . . . . . . . . . . . . . 101Receiving a Call While Alarms are Turned On . . 101Turning Off Non-Rearmable External Alarms . . . 101Turning Off Rearmable External Alarms . . . . . . . 102Using the Voice Announcement . . . . . . . . . . . . . 102Helpful Tips . . . . . . . . . . . . . . . . . . . . . . . . . . .104Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . .105Appendix: Maritime Radio Use in the VHF Frequency Range . . . . . . . . . . . . . . . . . . . . . .106Special Channel Assignments . . . . . . . . . . . . . . . 106Emergency Channel . . . . . . . . . . . . . . . . . . . . . . 106Non-Commercial Call Channel . . . . . . . . . . . . . . 106Operating Frequency Requirements . . . . . . . . . . . 107O5Head_6875947M01_C.book Page vii Wednesday, October 20, 2010 12:13 PM
ContentsEnglishviiiGlossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109Commercial Warranty and Service . . . . . . . .113O5Head_6875947M01_C.book Page viii Wednesday, October 20, 2010 12:13 PM
Important Safety InformationEnglishixImportant Safety InformationProduct Safety and RF Exposure ComplianceATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed with your radio (Motorola Publication part number 6881095C99) to ensure compliance with RF energy exposure limits. For a list of Motorola-approved antennas and other accessories, visit the following website: http://www.motorola.com/governmentandenterpriseSoftware VersionAll the features described in the following sections are supported by the radio's software version R05.00.00 or later.Accessing Radio Information on page 98 to determine your radio's software version. Check with your dealer or system administrator for more details of all the features supported.Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio.!O5Head_6875947M01_C.book Page ix Wednesday, October 20, 2010 12:13 PM
Computer Software CopyrightsEnglishxComputer Software CopyrightsThe Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied, reproduced, modified, reverse-engineered, or distributed in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive license to use that arises by operation of law in the sale of a product.Documentation CopyrightsNo duplication or distribution of this document or any portion thereof shall take place without the express written permission of Motorola. No part of this manual may be reproduced, distributed, or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of Motorola.DisclaimerThe information in this document is carefully examined, and is believed to be entirely reliable. However, no responsibility is assumed for inaccuracies. Furthermore, Motorola reserves the right to make changes to any products herein to improve readability, function, or design. Motorola does not assume any liability arising out of the applications or use of any product or circuit described herein; nor does it cover any license under its patent rights, nor the rights of others. O5Head_6875947M01_C.book Page x Wednesday, October 20, 2010 12:13 PM
Getting StartedEnglish1Getting StartedTake a moment to review the following:How to Use This User Guide. . . . . . . . . . . . . . . . . . . . . page 1Notations Used in This Manual . . . . . . . . . . . . . . . . . . . page 1Additional Performance Enhancement . . . . . . . . . . . . . page 2What Your Dealer/System Administrator Can Tell You . page 3How to Use This User GuideThis User Guide covers the basic operation of the APX™ Mobile Radios.However, your dealer or system administrator may have customized your radio for your specific needs. Check with your dealer or system administrator for more information.Notations Used in This ManualThroughout the text in this publication, you will notice the use of WARNING, Caution, and Note. These notations are used to emphasize that safety hazards exist, and the care that must be taken or observed.The following special notations identify certain items:An operational procedure, practice, or condition, etc., which may result in injury or death if not carefully observed.An operational procedure, practice, or condition, etc., which may result in damage to the equipment if not carefully observed.Note: An operational procedure, practice, or condition, etc., which is essential to emphasize.!W A R N I N G!!O5Head_6875947M01_C.book Page 1 Wednesday, October 20, 2010 12:13 PM
Getting StartedEnglish2Additional Performance EnhancementThe following are some of the latest creations designed to enhance the security, quality and efficiency of APX mobile radios.Dynamic System Resilience (DSR)DSR ensures the radio system is seamlessly switched to a backup master site dynamically in case of system failure. DSR also provides additional indication e.g. failure detection, fault recovery, and redundancy within the system to address to the user in need. Mechanisms related to the Integrated Voice and Data (IV & D) or data centric are all supported by DSR.CrossTalk PreventionThis feature prevents crosstalk scenario from happening, especially when a wideband antenna is used. This feature allows the adjustment of the Trident Transmitting SSI clock rate in the radio to be varied from the Receiving Frequency. This subsequently reduced the possibilities of radio frequency interfering spurs and prevents the issues of crosstalk. Encrypted Integrated Data (EID) EID provides security encryption and authentication of IV & D data bearer service communication between the radio and the Customer Enterprise Network.SecureNetSecureNet allows user to perform secured communications on an Analog or Motorola Data Communication (MDC) channel. The MDC OTAR feature will allow users to perform OTAR activities on an MDC channel.Example DescriptionHome button or HButtons and keys are shown in bold print or as an icon.PHONE Menu entries are shown similar to the way they appear on the radio’s display.>This means “Press the right side of the 4-way Navigation button.”O5Head_6875947M01_C.book Page 2 Wednesday, October 20, 2010 12:13 PM
Preparing Your Radio for UseEnglish3What Your Dealer/System Administrator Can Tell YouYou can consult your dealer or system administrator about the following:•Is your radio preprogrammed with any preset conventional channels?•Which buttons have been programmed to access other features? •What optional accessories may suit your needs?Preparing Your Radio for UseTurning On the Radio. . . . . . . . . . . . . . . . . . . . . . . . . . page 4 Validating Compatibility During Power Up. . . . . . . . . .page 4Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . .page 5O5Head_6875947M01_C.book Page 3 Wednesday, October 20, 2010 12:13 PM
Preparing Your Radio for UseEnglish4Turning On the RadioPress the Power On/Off Button briefly to power on the radio. After a short time, the red, yellow and green LEDs light up. The display then shows Zone and channel text, and menu items display on the screen. The backlight will turn on to the last selected dim level. Note: Pressing the Power On/Off Button before the LED lights up will be ignored.If FAIL ##/## appears in the display, the radio will not function until the condition has been corrected.If ERROR ##/## appears, some non-critical data has been changed. If either of these displays appear, if the display goes blank, or if the unit appears to be locked up, see Helpful Tips on page 104 for more information.If CH MISMATCH appears, means that either the Control Head has been connected to an incompatible transceiver, or vice versa.If your radio does not power up, contact your dealer. To turn off the radio, press the Power On/Off Button after the LEDs light up.Validating Compatibility During Power UpThe radio validates and updates the software and hardware of your control head(s) during power up. Follow the procedure below when your radio runs this task. Procedure:1The display shows MAINTENANCE MODE REMOTE DEVICE; promptly followed by other maintenance statuses. 2The display shows UPDATE DONE PLEASE RESET upon completion.ORThe display shows UPDATE FAILED PLEASE RESET when it fails to update. 3Press the Power On/Off Button to reset. The radio runs the usual power up operation if the software updates are complete.ORThe radio runs the Maintenance Mode if the updates are not complete and repeat step 1.Note: If SW INCOMPLETE appears, use Flashport Recovery Tool to update the control heads before you power on the radio again.Power On/Off ButtonO5Head_6875947M01_C.book Page 4 Wednesday, October 20, 2010 12:13 PM
Identifying Radio ControlsEnglish5Adjusting the VolumeTo increase the volume, rotate the Volume Knob clockwise. To decrease the volume, rotate the Volume Knob counterclockwise.Identifying Radio ControlsTake a moment to review the following:Radio Parts and Controls. . . . . . . . . . . . . . . . . . . . . . . .page 6O5 Control Head and Microphone . . . . . . . . . . . . . . .page 6Programmable Features . . . . . . . . . . . . . . . . . . . . . . . .page 7Assignable Radio Functions. . . . . . . . . . . . . . . . . . . .page 7Assignable Settings or Utility Functions . . . . . . . . . . .page 9Accessing the Preprogrammed Functions . . . . . . . . . . .page 9Using the Menu Select Buttons . . . . . . . . . . . . . . . . .page 9Using the Advance Programmable Buttons . . . . . . .page 10Using the Navigation Buttons . . . . . . . . . . . . . . . . . .page 10Using the Keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 12Keypad Characters – Uppercase Mode . . . . . . . . . .page 12Keypad Characters – Lowercase Mode . . . . . . . . . .page 13Keypad Characters – Numeric Mode . . . . . . . . . . . .page 14Keypad Characters – Hexadecimal Mode . . . . . . . .page 15Push-To-Talk (PTT) Button. . . . . . . . . . . . . . . . . . . . . .page 16Volume KnobO5Head_6875947M01_C.book Page 5 Wednesday, October 20, 2010 12:13 PM
Identifying Radio ControlsEnglish6Radio Parts and Controls O5 Control Head and Microphone Note: The microphone is not part of a radio. It is an optional accessory. 121316 15 14Volume KnobDim ButtonHome ButtonPower On/Off ButtonIndicatorsMode KnobOrange Button*Push-to-Talk (PTT) Button Accy No-Dot Button (Purple)*11Accy 2-Dot Button*Navigation ButtonLED IndicatorsMenu EntriesMenu Select Button*Accessory Port (Microphone)1*These controls/buttons are programmable.109823456Accy 1-Dot Button*7Home Button (Microphone)Data Feature Button*Okay/Select Button (3)Cancel Button (2)Navigation Button (Microphone)Keypad Buttons *This button is programmable.171822212019O5Head_6875947M01_C.book Page 6 Wednesday, October 20, 2010 12:13 PM
Identifying Radio ControlsEnglish7Programmable Features Any reference in this manual to a control that is “preprogrammed” means that the control must be programmed by a dealer or a qualified radio technician using the radio’s programming software, in order to assign a feature to that control.The programmable buttons can be programmed as shortcuts to radio functions or preset channels/groups depending on the duration of a button press:•Press – Pressing and releasing rapidly.•Long press – Pressing and holding for the programmed duration (between 0.25 seconds and 3.75 seconds).•Hold down – Keeping the button pressed.Assignable Radio FunctionsCall Alert – Allows the radio to function like a pager, or to verify if a radio is active on the system.Call Response – Allows you to answer a private call or phone call.Channel – Selects a channel.Contacts – Selects the Contacts menu.Dynamic Priority (Conventional Only) – Allows any channel in a scan list (except for the Priority-One channel) to temporarily replace the Priority-Two channel.Emergency – Depending on the programming, initiates or cancels an emergency alarm or call.Information – Displays the basic radio information, IP-related information, and buttons or switches control mapping.Intercom – Enables users of multiple control heads to talk to each other via the control heads in a multi-control head setup.Internet Protocol Address – Displays the Internet Protocol (IP) address, device name, and status of the radio.Location – Determines the current location (latitude, longitude, time and date), and also the distance and bearing to another location. Or, turns the GPS functionality on or off for all locations.Message – Enters the current message list.Monitor (Conventional Only) – Monitors a selected channel for all radio traffic until function is disabled.Multiple Private Line (Conventional Only) – Selects the Multiple Private Line lists.Nuisance Delete – Temporarily removes an unwanted channel, except for priority channels or the designated transmit channel, from the scan list. O5Head_6875947M01_C.book Page 7 Wednesday, October 20, 2010 12:13 PM
Identifying Radio ControlsEnglish8One Touch 1 – 4 – Launches a specific feature with one single button-press. You can setup as much as four separately programmed buttons for four different features.Phone – Allows you to make and receive calls similar to standard phone calls.Private Call (Trunking Only) – Allows a call from an individual radio to another individual radio.Radio Profiles – Allows for easy access to a set of preprogrammed visual and audio settings of the radio.Recent Calls – Allows for easy access to the list of calls recently received or made.Rekey Request – Notifies the dispatcher that you require a new encryption key.Repeater Access Button (RAB) (Conventional Only) – Allows to manually send a repeater access codeword. Reprogram Request (Trunking Only) – Notifies the dispatcher that you want a new dynamic regrouping assignment.Request-To-Talk (Conventional Only) – Notifies the dispatcher that you want to send a voice call.Scan – Toggles scan on or off. Secure/Clear – Toggles secure transmission on or off.Selective Call (Conventional Only) – Calls an assigned radio.Site Display (Trunking Only) – Views the current site or enable a site search for SmartZone operation.Site Lock/Unlock (Trunking Only) – Toggles between lock and unlock mode when using the SmartZone option.Status – Sends data calls to the dispatcher about a predefined status.Talkaround/Direct (Conventional Only) – Toggles between using a repeater and communicating directly with another radio.Talkgroup (Conventional Only) – Allows a call from an individual radio to a group of radios.Text Messaging Service (TMS) – Selects the text messaging menu.TMS Quick Text – Selects a predefined message. User – Automatically registers with the server.Zone Down – Toggles downward through the zones in the radio.Zone Select – Allows selection from a list of zones.Zone Up – Toggles upward through the zones in the radio.O5Head_6875947M01_C.book Page 8 Wednesday, October 20, 2010 12:13 PM
Identifying Radio ControlsEnglish9Assignable Settings or Utility FunctionsDim – Changes the display brightness.Front/Rear – Switches one of two control heads to be active at one time.Horns/Lights – Toggles horns and lights feature on or off.Low Power – Toggles transmit power level between high and low.Voice Announcement – Audibly indicates the current feature mode, Zone or Channel the user has just assigned. Voice Mute – Toggles voice mute on or off for the channels which have enabled In-Call User Alert. When Voice Mute is active, the radio remains muted to all conventional dispatch calls and affiliated trunking group calls.Accessing the Preprogrammed Functions You can access various radio functions through one of the following ways:•A short or long press of the relevant programmable buttons.OR•Use the Menu Select Button (g).Using the Menu Select ButtonsThe Menu Select Buttons allow to access the menu entries of features. Note: Check with your dealer or system administrator for the list of features activated in your radio.Your radio may be preprogrammed differently from the following example, but the steps for selecting a channel may appear as shown below: •Press the Menu Select button (g) directly below CHAN. Menu Select ButtonO5Head_6875947M01_C.book Page 9 Wednesday, October 20, 2010 12:13 PM
Identifying Radio ControlsEnglish10Using the Advance Programmable ButtonsThis feature is to help you to shorten the process of applying certain common features. * These programmable buttons support the One Touch Button feature. (Quick Access) One Touch Button – Enters a menu with a short press on the preprogrammed One Touch button. Features assigned to these buttons are Call, Call Alert, Phone, Repeater Access, MDC RTT Button Access, Status and Message. Using the Navigation ButtonsHome Button The H button returns you to the home (default) display. In most cases, this is the current mode. For selected radio features, the H button is also used to save user-edited radio settings or information before returning you to the Home screen.Note: Some features do not require you to press H to go to the Home screen. Refer to the individual feature sections in this manual for further details on saving user-edited radio settings or information.The H button also can revert to home channel. Check with your dealer or system administrator for more information.Data Feature Button Use this button to access data-related features, such as the Text Messaging Service (TMS) feature screen.Accy No-Dot Button (Purple)*Accy 1-Dot Button*Accy 2-Dot Button*Menu Select Button*Orange Button*O5Head_6875947M01_C.book Page 10 Wednesday, October 20, 2010 12:13 PM
Identifying Radio ControlsEnglish114-Way Navigation ButtonUse this button to scroll up, down, left or right.Press and release one of the button to scroll from one entry to the next one. Press and hold one of the button to have the radio toggles through the list automatically (release the button to stop). Volume Knob Use this Volume Knob to adjust the volume of the speakers by turning it clockwise or counterclockwise.Mode Knob Use this Mode Knob to scroll through the channels by turning it clockwise or counterclockwise.O5Head_6875947M01_C.book Page 11 Wednesday, October 20, 2010 12:13 PM
Identifying Radio ControlsEnglish12Using the Keypad You can use the 3 x 4 alphanumeric keypad on the keypad microphone to access your radio’s features. The keypad functions in a manner similar to a standard telephone keypad when entering numeric digits. When the keypad is used to edit a list, each key can generate different characters of the alphabet. The tables below show the number of times a key needs to be pressed to generate the required character.Keypad Characters – Uppercase ModeNumber of Times Key is PressedKey12345678910111213141516171819202111.,?! ;@_-*#&$/+=\“ ‘ ()2ABC3DEF4GH I5JKL6MNO7PQRS8TUV89WX Y Z0Toggle between mixed case mode, uppercase mode, and lowercase mode.*Space#Toggle between numeric and letter mode.O5Head_6875947M01_C.book Page 12 Wednesday, October 20, 2010 12:13 PM
Identifying Radio ControlsEnglish13Keypad Characters – Lowercase ModeNumber of Times Key is PressedKey12345678910111213141516171819202111.,?! ;@_-*#&$/+=\“ ‘ ()2abc3def4gh i5jkl6mno7pqrs8tuv9wxyz0Toggle between mixed case mode, uppercase mode, and lowercase mode.*Space#Toggle between numeric and letter mode. O5Head_6875947M01_C.book Page 13 Wednesday, October 20, 2010 12:13 PM
Identifying Radio ControlsEnglish14Keypad Characters – Numeric Mode Number of Times Key is PressedKey12345678910111213141516171819202111.,?! ;@_-*#&$/+=\“ ‘ ()22334455667788990 0*Space#Toggle between numeric and letter mode.O5Head_6875947M01_C.book Page 14 Wednesday, October 20, 2010 12:13 PM
Identifying Radio ControlsEnglish15 Keypad Characters – Hexadecimal Mode Number of Times Key is PressedKey1234567891011121314151617181920211122ABC33DEF4455667788990 0*Not applicable#Not applicableO5Head_6875947M01_C.book Page 15 Wednesday, October 20, 2010 12:13 PM
Identifying Status IndicatorsEnglish16Push-To-Talk (PTT) Button The PTT button on the side of the microphone serves two basic purposes: •While a call is in progress, the PTT button allows the radio to transmit to other radios in the call.Press and hold down PTT button to talk. Release the PTT button to listen.The microphone is activated when the PTT button is pressed.•While a call is not in progress, the PTT button is used to make a new call. See Making a Radio Call on page 30 for more information.Identifying Status IndicatorsYour radio indicates its operational status through the following:Status Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 17Text Messaging Service (TMS) Icons . . . . . . . . . . . . . page 19Status Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 19TMS Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . page 20LED Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 21Intelligent Lighting Indicators . . . . . . . . . . . . . . . . . . . . page 22Alert Tones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 23PTT ButtonO5Head_6875947M01_C.book Page 16 Wednesday, October 20, 2010 12:13 PM
Identifying Status IndicatorsEnglish17Status Icons The liquid crystal display (LCD) of your radio shows the radio status, text entries, and menu entries.The following are the icons that appear on the radio’s display. ReceivingRadio is receiving a call or data.TransmittingRadio is transmitting a call or data.Call ReceivedRadio has received an Individual Call.Received Signal Strength Indicator (RSSI)The number of bars displayed represents the received signal strength for the current site, for trunking only. The more stripes in the icon, the stronger the signal.utFVDirect•On = Radio is currently configured for direct radio-to-radio communication (during conventional operation only).•Off = Radio is connected with other radios through a repeater.Monitor (Carrier Squelch)Selected channel is being monitored (during conventional operation only).In-Call User Alert•On = The feature is enabled. Voice muting of the affiliated trunking talkgroup or selected conventional channel is activated.•Off = The feature is disabled. Voice muting of the affiliated trunking talkgroup or selected conventional channel is deactivated.Power Level•L = Radio is set at Low power.•H = Radio is set at High power.ScanRadio is scanning a scan list.NMKH or .iO5Head_6875947M01_C.book Page 17 Wednesday, October 20, 2010 12:13 PM
Identifying Status IndicatorsEnglish18Priority Channel Scan•Blinking dot = Radio detects activity on channel designated as Priority-One.•Steady dot = Radio detects activity on channel designated as Priority-Two.View/Program ModeRadio is in the view or program mode.•On steady = View mode•Blinking = Program modeVote Scan EnabledThe vote scan feature is enabled.Secure Operation•On = Secure operation.•Off = Clear operation.•Blinking = Receiving an encrypted voice call.AES Secure Operation•On = AES Secure operation.•Off = Clear operation.•Blinking = Receiving an encrypted voice call.jkmlLocation Signal•On = Location feature is enabled, and location signal is available.•Off = Location feature is disabled.•Blinking = Location feature is enabled, but no location signal is available.User Login Indicator (IP Packet Data)•On = User is currently associated with the radio.•Off = User is currently not associated with the radio.•Blinking = Device registration or user registration with the server failed due to an invalid username or pin.Data ActivityData activity is present.HexadecimalIndicates that the text entry is currently in hexadecimal mode.Gno{O5Head_6875947M01_C.book Page 18 Wednesday, October 20, 2010 12:13 PM
Identifying Status IndicatorsEnglish19Text Messaging Service (TMS) IconsThis feature allows you to send and receive text messages. See Text Messaging Service (TMS) on page 63 for more information.Status IconsThe following icons appear on the radio’s display for TMS features: Inbox FullThe Inbox is full.Message SentThe text message is sent successfully.Message UnsentThe text message cannot be sent.Unread Message•User receives a new message.•The selected text message in the Inbox has not been read.,[ZrRead MessageThe selected text message in the Inbox has been read.3/6Message IndexIndicates the index of the current message the user is viewing. Example: If the user is looking at the third message out of a total of 6 messages in the Inbox folder, the icon is displayed as the icon on the left column.Priority Status•The “Priority” feature is toggled on before the message is sent.•Messages in the Inbox folder are flagged with “Priority”.Request Reply•The “Request Reply” feature is toggled on before the message is sent.•Messages in the Inbox folder are flagged with “Request Reply”.]IP;pO5Head_6875947M01_C.book Page 19 Wednesday, October 20, 2010 12:13 PM
Identifying Status IndicatorsEnglish20TMS Menu Options Priority Status and Request Reply•User is composing a message with a priority status and a request for a reply.•Messages in the Inbox folder are flagged with ”Priority” and “Request Reply”.NumericIndicates that the text entry is currently in numeric mode.Mixed CaseIndicates that the text entry is currently in normal text mode.UppercaseIndicates that the text entry is currently in uppercase mode.LowercaseIndicates that the text entry is currently in lowercase mode.q213}Menu Option Description/FunctionINBX Brings you to your incoming messages screen. COMP Brings you to the compose screen.DRFT Brings you to the saved message screen. SENT Brings you to the sent messages screen. BACK Brings you back to the previous menu screen.EDIT Edits a draft message or key in a target address.SAVE Saves the messages you have edited to the Draft folder.RPLY Replies to a message.DEL Deletes a message or a character text during editing mode.NEW Creates a new message.LIST Brings you to the predefined messages screen.IMPT Toggles the “Priority Status” icon on or off for an outgoing message.RQRP Toggles “Request Reply” icon on or off for an outgoing message.O5Head_6875947M01_C.book Page 20 Wednesday, October 20, 2010 12:13 PM
Identifying Status IndicatorsEnglish21LED Indicator LED indicator shows the operational status of your radio. Solid red – Radio is transmitting.Rapidly blinking red – Radio has failed the self test upon powering up or encountered a fatal error.Solid yellow – Channel is busy.Blinking yellow – Radio is receiving a secured transmission.Solid green – Radio is powering up, or is on a non-priority channel while in the Scan List Programming mode.Blinking green – Radio is receiving an individual or telephone call, or is on a Priority-Two channel while in the Scan List Programming mode.Rapidly blinking green – Radio is on a Priority-One channel while in the Scan List Programming mode. CURR Deletes the current selected message.ALL Selects to delete all the messages in the current folder.YES Deletes all the messages in the current folder.NO Cancel the delete all messages options.EXIT Exits to the Home screen.OPTN Brings you to the Options main screen.SEL Selects a predefined message or address.SEND Sends the message.Menu Option Description/FunctionRed LEDYellow LEDGreen LEDO5Head_6875947M01_C.book Page 21 Wednesday, October 20, 2010 12:13 PM
Identifying Status IndicatorsEnglish22Intelligent Lighting Indicators This feature temporary changes the radio’s display backlight color and the alert text background color to help signal that a radio event has occurred. Note: This feature must be preprogrammed by a qualified radio technician.Backlight Event When Orange Emergency Alerts The radio initiates an emergency alarm or call.The radio receives an emergency alarm or call.Red Critical AlertsThe radio is out of range.The radio enters failsoft mode.The radio is unable to establish a full connection with the system.The radio is unable to authenticate or register with the system.Green Call AlertsThe radio receives a private call.The radio receives a phone call.The radio receives a call alert.The radio receives a selective call.O5Head_6875947M01_C.book Page 22 Wednesday, October 20, 2010 12:13 PM
Identifying Status IndicatorsEnglish23Alert Tones An alert tone is a sound or group of sounds. Your radio uses alert tones to inform you of your radio’s conditions. The following table lists these tones and when they occur.You Hear Tone Name HeardShort, Low-Pitched ToneRadio Self Test Fail When radio fails its power-up self test.Reject When an unauthorized request is made.Time-Out Timer Warning Four seconds before time out.No ACK Received When radio fails to receive an acknowledgment.Individual Call Warning Tone When radio is in an individual call for greater than 6 seconds without any activity.Long, Low-Pitched ToneTime-Out Timer Timed Out When the Time-Out Timer has expired.Talk Prohibit/PTT Inhibit (When PTT button is pressed) transmissions are not allowed.Out of Range (When PTT button is pressed) the radio is out of range of the system.Invalid Mode When radio is on an unpreprogrammed channel.A Group of Low-Pitched Tones Busy When system is busy.O5Head_6875947M01_C.book Page 23 Wednesday, October 20, 2010 12:13 PM
Identifying Status IndicatorsEnglish24Short,Medium-PitchedToneValid Key-Press When correct key is pressed.Radio Self Test Pass When radio passes its power-up self test.Clear Voice At beginning of a non-coded communication.Priority Channel Received When activity on a priority channel is received.Emergency Alarm Entry When entering the emergency state.Central Echo When central controller has received a request from a radio.Long, Medium-PitchedToneVolume Set When volume is changed on a quiet channel.Emergency Exit When exiting the emergency state.A Group ofMedium-PitchedTonesFailsoft When the trunking system fails.Automatic Call Back When voice channel is available from previous request.Talk Permit (When PTT button is pressed) verifying system accepting transmissions.Keyfail When encryption key has been lost.Console Acknowledge When status, emergency alarm, or reprogram request ACK is received.Received Individual Call When Call Alert or Private Call is received.Call Alert Sent When Call Alert is received by the target radio.Site Trunking When a SmartZone trunking system fails.You Hear Tone Name HeardO5Head_6875947M01_C.book Page 24 Wednesday, October 20, 2010 12:13 PM
Identifying Status IndicatorsEnglish25RingingFast Ringing When system is searching for target of Private Call.Enhanced Call Sent When waiting for target of Private Call to answer the call.Phone Call Received When a land-to-mobile phone call is received.Gurgle Dynamic Regrouping (When the PTT button is pressed) a dynamic ID has been received.Unique, Low-Pitched Chirp New Message When a new message is received.Unique, High-Pitched Chirp Priority Status When a priority message is received.You Hear Tone Name HeardO5Head_6875947M01_C.book Page 25 Wednesday, October 20, 2010 12:13 PM
General Radio OperationEnglish26General Radio OperationOnce you understand how your APX Mobile Radio is configured, you are ready to use your radio.Use this navigation guide to familiarize yourself with the basic Call features:Selecting a Zone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 26Selecting a Radio Channel . . . . . . . . . . . . . . . . . . . . . page 27Receiving and Responding to a Radio Call. . . . . . . . . page 27Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . . . page 30Repeater or Direct Operation . . . . . . . . . . . . . . . . . . . page 33Monitoring Features . . . . . . . . . . . . . . . . . . . . . . . . . . page 33Selecting a ZoneA zone is a group of channels.Note: Your radio must be preprogrammed to allow you to use these features.Procedure:1> or < to ZONE.2Press the Menu Select button directly below ZONE. The display shows the current zone and channel.3> or < button until the desired zone is displayed.4Press H or the PTT button to confirm the selected zone number. 5Press the PTT button to begin transmitting on the displayed zone channel.O5Head_6875947M01_C.book Page 26 Wednesday, October 20, 2010 12:13 PM
General Radio OperationEnglish27Selecting a Radio ChannelA channel is a group of radio characteristics, such as transmit/receive frequency pairs.Use the following procedure to select a channel.Note: Your radio must be preprogrammed to allow you to use this feature. If you select a channel that is not within the preprogrammed band, the radio indicates that it is on an unsupported frequency with both audio and visual warnings. Consult a qualified radio technician for the right choice between the following methods.Procedure:Rotate the Mode knob until the display shows the desired channel.OR1Press and hold > to scroll to CHAN and press the Menu Select button directly below CHAN. The display shows the current zone and channel. 2Rotate the Mode knob to the desired channel.3Press H or the PTT button to confirm the channel. Press the PTT button to transmit on the displayed zone channel.Receiving and Responding to a Radio CallOnce you have selected the required channel and/or zone, you can proceed to receive and respond to calls. You see solid red while the radio is transmitting, and solid yellow when the radio is receiving a transmission (conventional mode only). There is no LED indication when the radio receives a transmission in trunking mode. If the radio is receiving a secure transmission, the LED blinks yellow.Red LEDYellow LEDGreen LEDO5Head_6875947M01_C.book Page 27 Wednesday, October 20, 2010 12:13 PM
General Radio OperationEnglish28Receiving and Responding to a Talkgroup CallTo receive a call from a group of users, your radio must be configured as part of that talkgroup.Procedure:When you receive a talkgroup call (while on the Home screen), depending on how your radio is preprogrammed:1ASTRO Conventional Only:The LED lights up solid yellow. The display shows the talkgroup alias or ID, and the caller alias or ID.ORTrunking Only:The display shows the caller alias or ID.2Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.3Press the PTT button to respond to the call. The LED lights up solid red.4Release the PTT button to listen.See Making a Talkgroup Call on page 30 for details on making a Talkgroup Call.Receiving and Responding to a Private Call (Trunking Only)A Private Call is a call from an individual radio to another individual radio.These one-to-one calls between two radios are not heard by others in the current talkgroup. The calling radio automatically verifies that the receiving radio is active on the system and can display the caller ID.Note: If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit.Procedure: When you receive a Private Call:1You hear two alert tones and the LED blinks green. The display shows CALL RECEIVED and the caller alias or ID. 2Press the Menu Select button directly below RESP within 20 seconds after the call indicators begin.3During the call, the display shows the caller alias (name), if it is in the call list.ORDuring the call, the display shows the caller ID (number), if the caller’s name is not in the call list.O5Head_6875947M01_C.book Page 28 Wednesday, October 20, 2010 12:13 PM
General Radio OperationEnglish294Press and hold the PTT button to talk. Release the PTT button to listen.5Press H to hang up and return to the Home screen.Note: If you press PTT button before pressing the Menu Select button directly below RESP, your conversation will be heard by all members of the talk group. If 20 seconds pass before you press the Menu Select button directly below the RESP, you will not respond privately to the call just received. Instead, you initiate a Private Call. See Making a Private Call (Trunking Only) on page 31 for details on making a Private Call.Receiving and Responding to a Telephone Call This feature allows you to receive calls similar to standard phone calls from a landline phone.Note: If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit.Procedure:1You hear a telephone-type ringing and the LED blinks green. The backlight of the screen turns green. The display shows PHONE CALL and the call received icon blinks.2Press the Menu Select button directly below RESP.3Press and hold the PTT button to talk. Release the PTT button to listen.4Press H or the Menu Select button directly below EXIT to hang up and return to the Home screen.See Making a Telephone Call on page 32 for details.O5Head_6875947M01_C.book Page 29 Wednesday, October 20, 2010 12:13 PM
General Radio OperationEnglish30Making a Radio CallYou can select a zone, channel, subscriber ID, or talkgroup by using:•The preprogrammed Zone menu•The Mode Knob•A preprogrammed One Touch button•The Contacts list (see Contacts on page 43).Note: If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit.Making a Talkgroup CallTo make a call to a group of users, your radio must be configured as part of that talkgroup.Procedure:1> or < to TGRP and press the Menu Select button directly below TGRP. The display shows the last-selected talkgroup. Press the Menu Select button directly below SEL. ORRotate the Mode Knob to select the channel with the desired talkgroup.2Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.3Press the PTT button to make the call.4ASTRO Conventional Only:The LED lights up solid red. The display shows the talkgroup alias or ID. ORTrunking Only:The LED lights up solid red.5Speak clearly into the microphone.6Release the PTT button to listen.O5Head_6875947M01_C.book Page 30 Wednesday, October 20, 2010 12:13 PM
General Radio OperationEnglish31Making a Private Call (Trunking Only)This feature allows you to send an individual Call Alert or page if there is no answer from the target radio. Your radio must be preprogrammed to allow you to use this feature.Procedure:Press the preprogrammed Quick Access (One-Touch) Enhanced Private Call button to dial the preprogrammed ID and proceed to Step 5.ORFollow the procedure below.1> or < to CALL. 2Press the Menu Select button directly below CALL. The display shows the last transmitted or received.3Press the Menu Select button directly below CNTS to scroll through and select the required ID. OR Press the Menu Select button directly below LIST to go to the first number of the call list.OR> or < to the required ID.ORUse the keypad to enter the required ID.4Press the PTT button to start the Private Call. 5A telephone-type ringing sounds if the receiving unit is in service. The display shows CALLING...<NUMBER> or CALLING...<ALIAS>. 6Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.7When you are connected, the display shows the ID of the target radio. Press and hold the PTT button to talk. Release the PTT button to listen.ORIf no acknowledgment is received, the display shows NO ACKNOWLEDGE.ORIf the target radio does not respond before the time out, the display shows NO ANSWER.8Press H to return to the Home screen.See Sending a Call Alert Page on page 55 for more information.O5Head_6875947M01_C.book Page 31 Wednesday, October 20, 2010 12:13 PM
General Radio OperationEnglish32Making a Telephone Call This feature allows you to make calls similar to standard phone calls to a mobile or landline phone.Procedure:Press the preprogrammed Quick Access (One-Touch) Phone Call button to dial the preprogrammed phone number and proceed to Step 5.ORFollow the procedure below.1> or < to PHON.2Press the Menu Select button directly below PHON. The display shows the last transmitted phone number.3Press the Menu Select button directly below CNTS to scroll through and select the required ID.ORPress the Menu Select button directly below LIST to go to the first number of the call list.OR> or < to the required phone number.ORUse the keypad to enter the required phone number.4Press and release the PTT button to dial the phone number.5Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.6When your call is answered, press the PTT button to talk.7Release the PTT button to listen.8Press H to return to the Home screen.See Alert Tones on page 23 for more information if your call is NOT answered.O5Head_6875947M01_C.book Page 32 Wednesday, October 20, 2010 12:13 PM
General Radio OperationEnglish33Repeater or Direct OperationThe REPEATER operation increases the radio’s range by connecting with other radios through a repeater. The transmit and receive frequencies are different.The DIRECT or “talkaround operation” allows you to bypass the repeater and connect directly to another radio. The transmit and receive frequencies are the same.Procedure: Press the preprogrammed Repeater/Direct switch to toggle between talkaround and repeater modes. OR Follow the procedure below.1> or < to DIR.2Press the Menu Select button directly below DIR.3The display shows REPEATER MODE if the radio is currently in Repeater mode.ORThe display shows DIRECT MODE and the Talkaround icon if the radio is currently in Direct mode (during conventional operation only).You can repeat step 2 to toggle between the two modes. Once in Direct Mode, press PTT button to start conversation with the radios nearby.Monitoring FeaturesRadio users who switch from analog to digital radios often assume that the lack of static on a digital channel is an indication that the radio is not working properly. This is not the case.Digital technology quiets the transmission by removing the “noise” from the signal and allowing only the clear voice or data information to be heard.Monitor a channel to ensure the channel is clear before transmitting.Monitoring a ChannelProcedure:Lift the microphone off hook. Conventional Modes Only:1Listen for activity on that channel. 2Adjust the Volume knob if necessary.3If you hear no activity, press and hold the PTT button to start your conversation.ORO5Head_6875947M01_C.book Page 33 Wednesday, October 20, 2010 12:13 PM
General Radio OperationEnglish34Trunked Modes Only:1Press the PTT button. 2If you hear two, short, high-pitched tones, or if you hear no tone and the t indicator lights steadily, then proceed with your message. 3Release the PTT button to receive (listen).If you are not in the range of the system, you may hear a continuous low-pitched tone and the display shows OUT OF RANGE. Conventional Mode OperationThis feature allows you to monitor channel traffic on conventional channels by defeating the coded squelch. Thus you can to listen to another user active on the channel. This way, you may be prevented from talking over someone else’s conversation. Note: This feature must first be enabled by a qualified radio technician or system administrator.Procedure:Take the control head off hook. (This is the same as monitor on. You hear all channel traffic.)OR1At Home mode where the default zone and channel are being displayed, > or < button to MON.2Press the Menu Select button directly below MON momentarily to activate monitoring. The display shows MONITOR ON.3Press the Menu Select button to deactivate the monitoring. The display shows MONITOR OFF. MONITOR ON shown on the display indicates that the radio is monitoring. Pressing the Menu Select button again turns monitor off and you don’t hear all channel traffic. If you try to transmit on a receive-only channel, you hear an invalid tone until you release the PTT button.O5Head_6875947M01_C.book Page 34 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish35Advanced Features Use this navigation guide to learn more about advanced features available with your radio:Advanced Call Features . . . . . . . . . . . . . . . . . . . . . . . page 35Multiple Control Head Features. . . . . . . . . . . . . . . . . . page 40Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 43Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 49Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 51Call Alert Paging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 54Emergency Operation . . . . . . . . . . . . . . . . . . . . . . . . . page 56Automatic Registration Service (ARS). . . . . . . . . . . . . page 60Text Messaging Service (TMS) . . . . . . . . . . . . . . . . . . page 63Secure Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . page 73The Global Positioning System (GPS) . . . . . . . . . . . . page 78Trunking System Controls . . . . . . . . . . . . . . . . . . . . . . page 86Ignition Switch Options . . . . . . . . . . . . . . . . . . . . . . . . page 90Utilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 92Advanced Call FeaturesCalling a Phone Not in the List1> or < to PHON.2Press the Menu Select button directly below PHON.3Enter the desired phone number from the optional keypad microphone. The display updates as the numbers are entered.4Press 3 button on the keypad microphone to make the call.5Press and hold the PTT button to talk. Release the PTT button to listen.6Press H or Menu Select button directly below PHON to exit.O5Head_6875947M01_C.book Page 35 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish36Receiving and Making a Selective Call (Conventional Only)This feature allows you to receive a call from or to call a specific individual. It is intended to provide privacy and to eliminate the annoyance of having to listen to conversations that are of no interest to you.Receiving a Selective CallProcedure:1When you receive a Selective Call, you hear two alert tones and the LED lights up solid yellow. The call received icons blink and the display alternates between CALL RECEIVED and the home display.2The speaker unmutes.3Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.4Press and hold the PTT button to talk. Release the PTT button to listen.Note: If you press PTT button before pressing the Menu Select button directly below CALL, your conversation will be heard by all members of the talk group.If 20 seconds pass before you press the Menu Select button directly below the CALL, you will not respond privately to the call just received. Instead, you initiate a Selective Call. See Making a Selective Call on page 36.Making a Selective CallProcedure:Press the preprogrammed Quick Access (One-Touch) Selective Call button to dial the preprogrammed ID and proceed to Step 4.ORFollow the procedure below.1> or < to CALL.2Press the Menu Select button directly below CALL. The display shows the last transmitted or received ID.3Press the Menu Select button directly below CNTS to scroll through and select the required ID.ORPress the Menu Select button directly below LIST to go to the last number dialed.OR> or < to the required ID.ORUse the keypad to enter the required ID.O5Head_6875947M01_C.book Page 36 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish374Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.5Press and hold the PTT button to start the Selective Call. The display shows the ID of the target radio. 6Release the PTT button to listen.7Press H to return to the Home screen.If you do not press H button to hang up, your radio will remain in Selective Call state with the other unit. You will miss all subfleet traffic and incoming phone calls.Using the Talkgroup Call Feature (Conventional Operation Only)This feature allows you to define a group of conventional system users so that they can share the use of a conventional channel.Note: Encryption keys are associated to talkgroups. When talkgroups are enabled, encryption keys are changed by changing the active talkgroup. See Secure Operations on page 73 for more information.Selecting a TalkgroupProcedure:1> or < to TGRP.2Press the Menu Select button directly below TGRP. The display shows the last talkgroup that was selected and stored.3> or < to PSET for the preset preprogrammed talkgroup. OR> or < to the required talkgroup.ORUse the keypad to enter the number of the correspondingtalkgroup in the list.4Press the Menu Select button directly below SEL to save the currently selected talkgroup and return to the Home screen.5If the encryption key associated to the new talkgroup is erased, a momentary key fail tone sounds and the display shows KEY FAIL.ORIf the encryption key that is associated to the new talkgroup is not allowed, a momentary key fail tone sounds and the display shows ILLEGAL KEY.6Press H or the PTT button to exit.O5Head_6875947M01_C.book Page 37 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish38Sending a Status CallThis feature allows you to send data calls to the dispatcher about a predefined status.Each status can have up to a 14-character name. A maximum of eight status conditions is possible.Note: If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit.Procedure:Press the preprogrammed Status button and proceed to Step 3.ORFollow the procedure below.1> or < to STS.2Press the Menu Select button directly below STS.3The display shows the last acknowledged status call, or the first status in the list.4> or < to the required status.ORUse the keypad to enter a number corresponding to the location in the status list.5Press the PTT button to send the status. The display shows PLEASE WAIT.6When the dispatcher acknowledges, four tones sound and the display shows ACK RECEIVED. The radio returns to normal dispatch operation.ORIf no acknowledgment is received, a low-pitched tone sounds and the display shows NO ACKNOWLEDGE.7Press H to return to the Home screen.No traffic is heard on trunked channels while Status Calls is selected. If the radio detects no Status Call activity for six seconds, an alert tone sounds until you press H or the PTT button.Using the Dynamic Regrouping Feature (Trunking Only) This feature allows the dispatcher to temporarily reassign selected radios to a single special channel so they can communicate with each other. This feature is typically used during special operations and is enabled by a qualified radio technician.You will not notice whether your radio has this feature enabled until a dynamic regrouping command is sent by the dispatcher.Note: If you try to access a zone or channel that has been reserved by the dispatcher as a dynamically regrouped mode for other users, an invalid tone sounds.O5Head_6875947M01_C.book Page 38 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish39Procedure:1When your radio is dynamically regrouped, it automatically switches to the dynamically regrouped channel. A “gurgle” tone sounds and the display shows the dynamically regrouped channel’s name.2Press the PTT button to talk. Release PTT button to listen.When the dispatcher cancels dynamic regrouping, the radio automatically returns to the zone and channel that you were using before the radio was dynamically regrouped.Requesting a ReprogramThis feature lets you notify the dispatcher that you want a new dynamic regrouping assignment.Procedure:Press the preprogrammed Reprogram Request button to send reprogram request to the dispatcher and proceed to Step 3. OR Follow the procedure below.1> or < to RPGM.2Press the Menu Select button directly below RPGM to send reprogram request to the dispatcher.3The display shows REPROGRAM RQST and PLEASE WAIT.4If you hear five beeps, the dispatcher has acknowledged the reprogram request. The display shows ACK RECEIVED and the radio returns to the Home screen.ORIf the dispatcher does not acknowledge the reprogram request within six seconds, a low-pitched alert tone sounds and the display shows NO ACKNOWLEDGE. Try again or press H to cancel and return to the Home screen.Classifying Regrouped RadiosThe dispatcher can classify regrouped radios into either of two categories: Select Enabled or Select Disabled.•Select-enabled radios are free to change to any available channel, including the dynamic-regrouping channel, once the user has selected the dynamic-regrouping position.•Select-disabled radios cannot change channels while dynamically regrouped. The dispatcher has forced the radio to remain on the dynamic-regrouping channel.The Scan or Private Call feature cannot be selected while your radio is Select Disabled.O5Head_6875947M01_C.book Page 39 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish40Multiple Control Head FeaturesMultiple Control Head FeaturesThis feature allows a transceiver to control as many as four O5 control heads on APX 7500 and, up to two O5 control heads on APX 6500. You can use the CAN cables to connect in any configuration that does not exceed 131 feet (40 meters) in combined length. Refer the O5 Control Head Installation Manual (HLN6947) for further information.The Multiple Control Head (MCH) feature consists of 2 modes that can be programmed via Customer Programming Software (CPS):•All Active mode•One Active modeNote: If two or more control heads are connected to the system before enabling the MCH feature in the CPS, the radio will display EXTRA CH or CH ID # ERR. Both errors are FATAL.Setting the Initial Control Head’s IDThis feature allows you to setup the control head in the Front Panel Programming (FPP) mode. During the setup, the control heads are defined as Control Head Number 1, Control Head Number 2, Control Head Number 3 and Control Head Number 4. Procedure:1Press the Power button to power off the radio. 2Press and hold the left-most Menu Select button and the emergency button simultaneously. 3While continuing to depress these two buttons, press the Power button to power on the radio and the control head.4The radio and the control head will power on into FPP mode. The display shows control head’s ID number.5Turn the Mode knob to change the control head’s ID number.6Press the Power button to power off the radio and exit FPP mode.7Repeat steps 1 to 5 above to set the ID number for the rest of the attached control heads.O5Head_6875947M01_C.book Page 40 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish41All Active ModeThe All Active mode enables all connected control heads attached to the radio to operate concurrently with each other. When you activate a feature on one control head, the rest of the control heads will have the same activated features and indicators on their respective display. Note: The multiple control head feature allows only control heads of the same type to be connected. Upon power up, if a control head of a different type is connected to the radio, the radio reports the FATAL error CH MISMATCH on the display of all attached control heads.Intercom Feature in All Active ModeThe intercom feature allows one control head user to talk to another control head user in a Multiple Control Head configuration. At any given time, when a control head being operated has priority for the intercom call, all other control heads are blocked until the active control head releases PTT button.This can be made on any attached control head. This feature only applies to control heads in the All Active mode. Procedure:1Press the Menu Select button directly below INTC to activate the intercom feature of any of the control heads.2Press the PTT button to initiate an intercom transmission. All control heads that are attached will receive the same intercom call.3The display of the control heads receiving the intercom call shows the alias/ID number of the transmitting control head.4Press the Menu Select button directly below EXIT to deactivate the intercom feature.ORPress H to deactivate the intercom feature.The intercom feature also deactivates when user initiates a mode change. If the radio is on an emergency channel, pressing of the EMERGENCY button or the emergency footswitch button on any control head also deactivates the intercom feature.One Active ModeThe One Active mode enables only one control head to be visibly active at a time in a two control head system. Note: In the One Active mode, if more than two control heads are present upon power up, the radio shows a FATAL error EXTRA CH on the display of all attached control heads. The active control head commands the system normally while the inactive control head is in remote mode with its display shows REMOTE. O5Head_6875947M01_C.book Page 41 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish42The Volume knob, DIM button, Front/Rear (F/R) softkey and Emergency button remain active on the inactive control head, while all other controls are disabled. Emergency footswitch and VIP inputs remain active on the inactive control head. The VIP input control head is configurable in the CPS and VIP should be attached to the control head selected in the CPS. Note: Only two (2) control heads are supported in the one active mode.Follow the procedure below to change the command between the two control heads.Procedure:Press the Menu Select button directly below F/R.ORPress the Menu Select button preprogrammed user button on the keypad microphone.TransceiverZ1ZONECHANPWR SQLREMOTEF/RActive RadioNon-Active RadioO5Head_6875947M01_C.book Page 42 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish43ContactsThis feature provides “address-book” capabilities on your radio. Each entry corresponds to an alias (name) or ID (number) that you use to initiate a call.Contact entries are alphabetically sorted according to entry alias. Each alias can have up to 5 IDs of different call types associated with it.Additionally, each entry, depending on context (conventional, trunking, or phone), associates with one or more of the four types of calls: Phone Call, Selective Call, Private Call, or Call Alert.Each entry within Contacts displays the following information:•Call Alias (Name)•Call ID (Number)•Call Type (Icon)•WACN ID (Astro 25 Trunking IDs only)•System IDNote: Your radio must be preprogrammed to allow you to add, edit, or delete the contact entries.Your radio also supports a maximum of 50 call lists. Each list can store up to 100 IDs (numbers).Note: Your radio is preprogrammed with a number of contacts per Call Lists. Check with your dealer or system administrator for more information.If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit.Making a Private Call from ContactsNote: Your radio must be preprogrammed to allow you to use this feature.Procedure:Use the Options Menu.1> or < to CNTS.2Press the Menu Select button directly below CNTS to the call list. The display shows Contact Alias.3> or < to the required subscriber alias. 4Press the Menu Select button directly below OPTN.5> or < to CALL and press the Menu Select button directly below SEL.6> or < to select the call type.O5Head_6875947M01_C.book Page 43 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish447Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.8Press the PTT button to initiate the call. During the call, the display shows the subscriber alias.9Press and hold the PTT button to talk. The LED lights up solid red.ORRelease the PTT button to listen. The LED lights up solid green.10 If there is no voice activity for a programmed period of time, the call ends.ORThe call ends when it reaches the maximum ring time.ORUse the PTT button:1> or < to CNTS.2Press the Menu Select button directly below CNTS. 3> or < to the required subscriber alias. 4Press the Menu Select button directly below CNTS. The display shows Contact Alias.5Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.6Press the PTT button to initiate the call. During the call, the display shows the subscriber alias.7Press and hold the PTT button to talk. The LED lights up solid red.ORRelease the PTT button to listen. The LED lights up solid yellow.8If there is no voice activity for a preprogrammed period of time, the call ends.OR The call ends when it reaches the maximum ring time.O5Head_6875947M01_C.book Page 44 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish45Adding a New Contact EntryProcedure:1> or < to CNTS.2Press the Menu Select button directly below CNTS. The entries are alphabetically sorted.3> or < to {NEW CONTACT} and press the Menu Select button directly below SEL.4The display shows NAME. Press the Menu Select button directly below EDIT.Use the keypad to enter the name.Press < to move one space to the left. Press > to move one space to the right.Press the Menu Select button below DEL to delete any unwanted characters.Press * to add a space.Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode.Press # to toggle between numeric and letter mode.5Press the Menu Select button directly below OK once you have entered the name.ORPress the Menu Select button directly below CNCL to return to the previous screen. 6> or < to {ADD NUMBER} and press the Menu Select button directly below SEL. The display shows TYPE 1 <DEFAULT TYPE>. 7Press Menu Select button directly below EDIT. 8> or < to the required channel and press the Menu Select button directly below OK.9> or < to NUMBER 1 and press the Menu Select button directly below EDIT.The display shows NUMBER 1 and a cursor appears.Use the keypad to enter the number.Press < to move one space to the left.Press > to move one space to the right.Press the Menu Select button directly below DEL to delete any unwanted characters.10 Press the Menu Select button directly below OK once you have entered the number.ORPress the Menu Select button directly below CNCL to return to the previous screen.11 Press the Menu Select button directly below DONE once you have finished.12 The display shows <ENTRY> STORED, confirming that the contact entry has been added.13 The radio returns to the main Contacts screen.O5Head_6875947M01_C.book Page 45 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish46Deleting a Contact EntryProcedure:1> or < to CNTS.2Press the Menu Select button directly below CNTS. The entries are alphabetically sorted.3> or < to the entry you want to delete and press the Menu Select button directly below OPTN.4> or < to DELETE and press the Menu Select button directly below SEL. The display shows <ENTRY> CONFIRM DEL?.5Select YES to delete the entry.The display shows <ENTRY> DELETED and the radio returns to the main screen for Contacts.ORSelect NO to return to the main screen for Contacts.Adding a Contact to a Call List or Phone ListProcedure:1> or < to CNTS.2Press the Menu Select button directly below CNTS. The entries are alphabetically sorted.3> or < to the entry you want to add to the call list and press the Menu Select button directly below OPTN.4> or < to ADD TO CALLLST or ADD TO PHONLST and press the Menu Select button directly below SEL.5> or < until the display shows {AVAILABLE} and press the Menu Select button directly below ADD to add as a new entry. OR> or < until the display shows <ENTRY> and its associated number and press the Menu Select button directly below RPLC to replace the existing entry.6The display shows <ENTRY> ADDED, confirming the addition of the contact to the list.7The radio returns to the main display for Contacts.O5Head_6875947M01_C.book Page 46 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish47Editing a Contact in a Call List or a Phone ListEditing an Entry AliasProcedure:1> or < to CNTS.2Press the Menu Select button directly below CNTS. The entries are alphabetically sorted.3> or < to the entry you want to edit and press the Menu Select button directly below OPTN.4> or < to EDIT and press the Menu Select button directly below SEL.5> or < to the entry alias you wish to change and press the Menu Select button directly below EDIT.6A cursor appears.Use the keypad to edit the name.Press < to move one space to the left. Press > to move one space to the right.Press the Menu Select button below DEL to delete any unwanted characters.Press * to add a space.Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode.Press # to toggle between numeric and letter mode.7Press the Menu Select button directly below OK once you have finished. The display returns to the Edit Contact screen.8Press the Menu Select button directly below DONE to save your changes and return to the main screen for Contacts.Editing as Entry IDProcedure:1> or < to CNTS.2Press the Menu Select button directly below CNTS. The entries are alphabetically sorted.3> or < to the entry you want to edit and press the Menu Select button directly below OPTN.4> or < to EDIT and press the Menu Select button directly below SEL.5> or < to the entry ID you wish to change and press the Menu Select button directly below EDIT.6A cursor appears.Use the keypad to edit the number.Press < to move one space to the left. Press > to move one space to the right.Press the Menu Select button below DEL to delete any unwanted characters.O5Head_6875947M01_C.book Page 47 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish48Press * to add a space.Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode.Press # to toggle between numeric and letter mode.7Press the Menu Select button directly below OK once you have finished. The display returns to the Edit Contact screen.8Press the Menu Select button directly below DONE to save your changes and return to the main screen for Contacts.Editing a Call TypeProcedure:1> or < to CNTS.2Press the Menu Select button directly below CNTS. The entries are alphabetically sorted.3> or < to the entry you want to edit and press the Menu Select button directly below OPTN.4> or < to EDIT and press the Menu Select button directly below SEL.5> or < to TYPE and press the Menu Select button directly below EDIT.6> or < to choose from the list of call types given and press the Menu Select button directly below OK to select.7The display returns to the Edit Contact screen.8Press the Menu Select button directly below DONE to save your changes and return to the main screen for Contacts.O5Head_6875947M01_C.book Page 48 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish49Scan ListsScan lists are created and assigned to individual channels/groups. Your radio scans for voice activity by cycling through the channel/group sequence specified in the scan list for the current channel/group. Your radio supports different types of Scan Lists: • Trunking Priority Monitor Scan List• Conventional Scan List• Talkgroup Scan ListA maximum of 200 Scan Lists can be programmed in your radio. These lists must be preprogrammed by a qualified radio technician.Viewing a Scan ListProcedure:1> or < to SCNL.2Press the Menu Select button directly below SCNL.3> or < to view the members on the list.4Press the H to exit the current display and return to the Home screen.Editing the Scan ListThis feature lets you change scan list members and priorities.Procedure:1> or < to SCNL.2Press the Menu Select button directly below SCNL. The display shows the lists that can be changed.3> or < to the entry you want to edit.4Press the Menu Select button directly below SEL to add and/or change the priority of the currently displayed channel in the scan list.ORPress the Menu Select button directly below DEL to delete the currently displayed channel from the scan list.ORPress the Menu Select button directly below RCL to view the next member of the scan list.5> or < to select more channels to be added or deleted.ORUse the keypad to go directly to additional channels to be added or deleted.ORUse the Mode Knob to select additional channels to be added or deleted.O5Head_6875947M01_C.book Page 49 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish506Press H to exit scan list programming and return to the Home screen.See Viewing and Changing the Priority Status on page 50 for more information on how to add and/or change the priority of the currently displayed channel in the scan list.Changing the Scan List StatusProcedure:1Long press the preprogrammed Scan side button.2> or < to the member you want to edit.3Press the 3 button or press the Menu Select button directly below SEL once to add the currently displayed channel to the scan list.ORPress the 3 button or press the Menu Select button directly below SEL, one or more times to change the scan list status icon of the currently displayed channel.4> or < to select more list members whose scan status you want to change.ORUse the keypad to go directly to that scan list member.ORUse the Mode Knob to select another scan list member.5Press H to exit scan list programming and return to the Home screen.Viewing and Changing the Priority StatusProcedure:1Below the SEL, DEL, and RCL screen, press the Menu Select button directly below SEL to view and/or change the priority status of the currently displayed channel.OR Below the SEL, DEL, and RCL screen, press the 3 button or press the Menu Select button directly below SEL, one or more times to view and/or change the scan list status icon of the currently displayed channel.2A Scan icon indicates that the current channel is in the scan list as a non-priority channel. The LED lights up solid green.ORA Priority-Two Channel Scan icon indicates that the current channel is in the scan list as the Priority-Two channel. The LED blinks green. ORA Priority-One Channel Scan icon indicates that the current channel is in the scan list as the Priority-One channel. The LED rapidly blinks green. You hear all traffic on the Priority-One channel, regardless of traffic on non-priority channels.ORNo icon indicates that the current channel is deleted from the scan list.O5Head_6875947M01_C.book Page 50 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish51ScanThis feature allows you to monitor traffic on different channels by scanning a preprogrammed list of channels.Turning Scan On or OffProcedure: Press the preprogrammed Scan button. OR Follow the procedure below.1> or < to SCAN.2Press the Menu Select button directly below SCAN.3The display shows SCAN OFF if scan is disabled. Press the Menu Select button directly below SCAN to enable scan.ORThe display shows SCAN ON and the scan status icon if scan is enabled. Press the Menu Select button directly below SCAN to disable scan.4The radio returns to the Home screen.Turning Scan On While Disregarding the Squelch Code (Conventional Channels Only)Procedure: 1> or < to MON.2Press the Menu Select button directly below MON.3The brief MONITOR ON display indicates that the radio is disregarding the squelch code.While scanning for activity, you can still receive fleetwide, system-wide, dynamic regrouping, incoming telephone interconnect and Private Conversation/Call Alert calls.Respond to these types of calls as you would normally on the selected channel. However, when scanning different channels while in talkgroup scan, incoming Private Conversation/Call Alert calls may be missed.Transmitting While the Scan is OnRadio Programmed for Talkback Scan Procedure: 1Press the PTT button to transmit on the channel indicated by the display. O5Head_6875947M01_C.book Page 51 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish52The radio does not begin scanning again for a predetermined hang time after you release the PTT button, allowing the other party to respond. If the other party responds within the hang time, scanning does not resume until the full hang time expires after they have finished speaking, allowing the conversation to be completed.To transmit on the selected channel if another channel is active, first turn scan off by pressing the Menu Select button below SCAN momentarily.Radio Programmed for Non-Talkback ScanProcedure:1Press the PTT button at any time to transmit on the selected channel or fixed channel.To make a Call Alert page, or Private Conversation call while scanning, press either the Menu Select button directly below PAGE or CALL. The call is entered on the selected channel and scanning is halted until the call is exited by pressing H or pressing the Menu Select button below either PAGE or CALL.Deleting a Nuisance ChannelIf a channel continually generates unwanted calls or noise (termed a “nuisance” channel), you can temporarily remove the unwanted channel from the scan list.This capability does not apply to priority channels or the designated transmit channel.Procedure:1When the radio is locked onto the channel to be deleted,> or < to NUIS. 2Press the Menu Select button directly below NUIS. Restoring a Nuisance ChannelProcedure: To restore the deleted nuisance channel, do one of the following:•Turn scan off, then on.OR•Change modes.OR•Turn off the radio, and then turn it back on.Nuisance mode delete can be disabled by the system administrator.O5Head_6875947M01_C.book Page 52 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish53Changing Priorities Status While Scan is OnWhile the radio is scanning, the dynamic priority change feature allows you to temporarily change any channel in a scan list (except for the Priority-One channel) to the Priority-Two channel.This change remains in effect until scan is turned off. Scan then reverts to the preprogrammed (original) setting.Procedure: 1Press the Menu Select button directly below DYNP to change the priority of a non-priority channel in the scan list to Priority-Two.2Press H momentarily to exit the scan list and resume scanning.Restoring Priorities in a Scan ListProcedure: To restore the original channel priorities in a scan list, do one of the following:•Turn scan off, then on. OR•Change channels.OR•Turn off the radio, and then turn it back on.Hang Up (HUB)To temporarily suspend Scan Mode operation, remove the control head from the Hang Up Box (HUB). You are allowed to use the control head while scan is suspended. However, Priority Member scanning is not suspended. This feature applies to all Scan Lists and Scan Types. Scan is resumed once the control head is returned to the holding clip and the preprogrammed hang time has elapsed.Note: Priority Scan List members are continuously scanned only when the Scan List, Designated Tx Member field is set to “Talkback” in the radio programming. Otherwise, all scan mode operation is suspended.O5Head_6875947M01_C.book Page 53 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish54 Call Alert PagingThis feature allows your radio to work like a pager.Even if other users are away from their radios, or if they are unable to hear their radios, you can send them an individual Call Alert page. You can also verify if a radio is active on the system.Depending on how your radio is programmed, when you make an Enhanced Private Call, the radio either automatically sends a Call Alert page if there is no answer after the maximum ring time, OR when you press the PTT button.Note: This feature must be preprogrammed by a qualified radio technician.Receiving a Call Alert PageProcedure:When you receive a Call Alert page1You hear four repeating alert tone and the green LED blinks.ORYou hear one alert tone and the green LED blinks if Call Alert Tone Auto Reset is enabled.2The call received icons blinks and the display shows PAGE RECEIVED.3Press the PTT button to answer.ORPress any button to clear the Call Alert page.See Making a Talkgroup Call on page 30 or Making a Private Call (Trunking Only) on page 31 for more information.O5Head_6875947M01_C.book Page 54 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish55Sending a Call Alert PageNote: If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit.Procedure:Press the preprogrammed Quick Access (One-Touch) Call Alert Paging button to send a page to the preprogrammed ID and proceed to Step 5 of the procedure below. OR Follow the procedure below.1> or < to PAGE.2Press the Menu Select button directly below PAGE.3> or < to select the required ID.4Press the PTT button to send the page. 5The display shows PAGING...<NUMBER> or <ALIAS>.6If the call alert page is sent successfully, four highpitch tone sounds and the display shows ACK RECEIVED.ORIf the call alert page is not acknowledged, a low tone sounds and the display shows NO ACKNOWLEDGE.7The radio returns to the Home screen.ORPress the Menu Select button directly below OK to return to the main screen for Contacts.ORFollow the procedure below.1> or < to CALL.2Press the Menu Select button directly below CALL.3> or < to select the required ID, press the PTT button to initiate the call. 4If the target radio does not respond after a preprogrammed period of time, the display shows SEND PAGE?.5Press the Menu Select button directly below YES to send the call alert page.ORPress the Menu Select button directly below NO to exit the screen without sending the call alert page.6The display shows PAGING...<ALIAS>.7If the call alert page is sent successfully, a tone sounds and the display shows ACK RECEIVED.ORIf the call alert page is not acknowledged, a low tone sounds and the display shows NO ACKNOWLEDGE.8The radio returns to the Home screen.ORO5Head_6875947M01_C.book Page 55 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish56Press the Menu Select button directly below OK to return to the main screen for Contacts.In-Call User Alert You can enable and disable voice transmission, if needed.Procedure:1Make sure you are in Home mode where the default zone and mode are being displayed.2> or < to scroll to the VMUT.3Press the Menu Select button directly below VMUT. 4Press the Menu Select button directly below VMUT or the VMut preprogrammed button again to turn the feature off and you will be able to hear to normal dispatch calls.Pressing the Menu Select button directly below VMUT or the VMut programmed button momentarily toggles between Voice mute on and Voice mute off. VOICE MUTE ON shown on the display indicates that the radio is muted to all conventional dispatch calls and affiliated trunking group calls.Emergency OperationThe Emergency feature is used to indicate a critical situation. If the Orange button is preprogrammed to send an emergency signal, this signal overrides any other communication over the selected channel.Your radio supports 5 Emergency modes:•Emergency Call•Emergency Alarm•Emergency Alarm with Call•Silent Emergency Alarm•Special Considerations for EmergenciesCheck with your dealer or system administrator for more information on the programming of this feature.Only one of the Emergency modes above can be assigned to the preprogrammed Emergency button or the Emergency footswitch.Note: To exit emergency at any time, press and hold the preprogrammed Emergency button for about a second.O5Head_6875947M01_C.book Page 56 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish57Sending an Emergency AlarmThis feature allows you to send a data transmission, which identifies the radio sending the emergency, to the dispatcher.Procedure:1Press the preprogrammed Emergency button. A tone sounds and the display alternates EMERGENCY and the home display.2A dispatcher acknowledgment ACK RECEIVED display follows. AND, Trunking Only:A high-pitched tone indicates that the alarm has been received by the trunked system’s central controller.3Press and hold the emergency button or the PTT button to return to normal operation.Sending an Emergency Call (Trunking Only)Procedure:1Press preprogrammed Emergency button. 2A tone sounds and the display alternates EMERGENCY and the home display.ORA short low-pitched tone sounds when the selected channel does not support emergency.3Hold the microphone vertically 1 to 2 inches (2.0 to 2.5 cm) from your mouth. 4Press and hold the PTT button. Speak clearly into the microphone.5Release the PTT to end the transmission.6Press and hold the preprogrammed Emergency button until a tone sounds to exit Emergency mode. Sending an Emergency Alarm with Emergency CallThis feature allows you to send an Emergency Alarm to another radio. Upon acknowledgement, both radios can communicate over a preprogrammed Emergency channel.If the radio has both emergency call and alarm features enabled, it automatically proceeds to the call mode after the alarm is acknowledged.O5Head_6875947M01_C.book Page 57 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish58Procedure:1Press the preprogrammed Emergency button to activate the emergency call/alarm feature.2The display alternates EMERGENCY and the home display.3A high-pitched tone sounds, indicating that the alarm has been received by the trunked system’s central controller.A dispatcher acknowledgment (four high-pitched tones) follows, accompanied by an ACK RECEIVED display.4Hold the microphone vertically 1 to 2 inches (2.0 to 2.5 cm) from your mouth. 5Press and hold the PTT button. Speak clearly into the microphone.6Release the PTT to end the transmission.7Press and hold the preprogrammed Emergency button until a tone sounds to exit Emergency mode. Turning the radio off also cancels the emergency state.Sending a Silent Emergency AlarmThis feature allows you to send an Emergency Alarm to another radio without any audio or visual indicator.Upon acknowledgement, your radio’s microphone is automatically activated, allowing you to communicate with the other radio without pressing the PTT button. This activated microphone state is also known as “hot mic”.Note: If you press the PTT button during hot mic, and continue to press it after the hot mic duration expires, the radio continues to transmit until you release the PTT button. Procedure: 1Press the preprogrammed Emergency button to activate the silent alarm feature.2Press and hold the emergency button until a tone sounds to exit the silent alarm mode.If silent emergency alarm is used with emergency call, pressing the PTT button exits the silent mode and initiates the emergency call.O5Head_6875947M01_C.book Page 58 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish59Special Considerations for Emergencies•If you press the emergency button while in a channel that has no emergency capability, a low-pitched tone sounds.•If the unit is out of the range of the system and/or the emergency alarm is not acknowledged, a tone sounds and the display shows NO ACKNOWLEDGE.•If you press the emergency button, then change to a mode that has no emergency capability, the display shows NO EMERGENCY and a continuous low-pitched tone sounds until a valid emergency mode is selected or until the emergency is cancelled.•When an emergency is active, changing to another mode where emergency is enabled (trunked or conventional) causes an emergency alarm and/or emergency call to be active on the new mode.O5Head_6875947M01_C.book Page 59 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish60Advanced FeaturesAutomatic Registration Service (ARS)This feature provides an automated data application registration for the radio. When you turn on the radio, the device automatically registers with the server. Data applications within the fixed network can determine the presence of a device on the system and send data to the device. For example: Text Messaging Service (TMS). The Automatic Registration Service for the radio consists of two (2) modes:•ARS Server Mode (default mode)•ARS Non Server ModeNote: The default ARS mode can be changed by a qualified radio technician using the radio’s programming software.Selecting or Changing ARS ModeProcedure:1After the zone you want is displayed, toggle until the display shows the required channel.ORPress and hold > or < to CHAN.Press the Menu Select button directly below CHAN. The display shows the current zone is not blinking, and the channel is blinking.2> or < or rotate the Mode Knob to the required channel.3In ARS Server Mode, the display shows the User Login Indicator icon, the zone, and ARS server channel.ORIn ARS Non-Server Mode, the display shows the User Login Indicator icon, the zone, and ARS non-server channel.ORIf the channel or mode selected is unprogrammed, the display shows UNPROGRAMMED. Repeat Step 2.4Press H to confirm the displayed zone and channel. O5Head_6875947M01_C.book Page 60 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish61Accessing the User Login FeatureThis feature allows you as the user to be associated with the radio. With this association, every data application (Example: Text Messaging Service) takes on a friendly username. You can still send text messages without logging in as a user. The user login feature only enables the recipient of your message to identify you as the sender by assigning a username to your message.Note: Valid characters for a username entry are capital letters (A – Z), small letters (a – z), numbers (0 – 9), symbols (*, #, -, /), and the space character.The maximum length for a username is eight (8) characters. Usernames are not case sensitive in server mode but are case sensitive in non-server mode.A predefined username may sometimes be invalid because the programming software that is used to set predefined usernames allows you to set usernames comprising of eight (8) characters or more.Logging In as a UserProcedure:1> or < to USER.2Press the Menu Select button directly below USER. 3The display shows the User Login screen.4Press the Menu Select button directly below ID.5A blinking cursor appears beside ID. Use the keypad to enter a username using the keypad multi-tap function. OR> or < to scroll through the list of predefined usernames. Press the Menu Select button to select a predefined username.ORPress and hold > or < to scroll through the list of predefined usernames at a fast scroll rate. Press the Menu Select button directly below LOGN to select a predefined username.6If the selected predefined username has more than eight (8) characters, or an invalid character in it, the display momentary shows INVALID ID. Repeat Step 5.ORPress the Menu Select button directly below PIN.7A blinking cursor appears beside PIN. Enter your Personal Identification Number (PIN) number. O5Head_6875947M01_C.book Page 61 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish62The maximum PIN length is 4 digits. The PIN number will appear as asterisks.8Press the Menu Select button directly below LOGN. 9In ARS server mode, the display shows the User Login Indicator icon, the ID, IN PPROGRESS and CNCL.ORIn ARS non-server mode, the display shows the User Login Indicator icon, the ID, LOGGED IN and LOGT. In non-ARS enabled mode, the display shows OFFLINE and LOGT.10 If the username is invalid, login fails and the user login failure indicator (IP indicator) icon blinks. The display also momentary shows LOGIN FAILED. Repeat step 5.ORIf the PIN is invalid, login fails and the user login failure indicator (IP indicator) icon blinks. The display also momentary shows LOGIN FAILED. Repeat Step 7.ORPress the Menu Select button directly below CNCL to cancel the login in progress screen and return to the initial user login screen. ORWait for the logged in confirmation screen. If the login process is successful, the display shows the successful user login indicator (IP indicator) icon and LOGGED IN and LOGT. Logging OutOnce the data application registration is completed, you can log out.Procedure:1> or < to LOGT.2Press the Menu Select button directly below LOGT.3Display shows the User Login Indicator icon and CLEAR PRIVATE DATA?.4Select YES to clear all your private data. The display shows momentary PRIVATE DATA CLEARED. ORSelect NO to keep your private data.Note: Private data refers to all messages in the text messaging Inbox, Draft and Sent folder. The next radio user will be able to access your Inbox, Draft and Sent messages if private data is not deleted.O5Head_6875947M01_C.book Page 62 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish63Text Messaging Service (TMS)This feature allows you to send and receive text messages. The maximum length of characters for a text message is 200.There are three (3) types of text messages:•A new text message (free form message)•A predefined message (quick text message)•An edited quick text messageThe main menu consists of the following options:•Inbox•Compose•Drafts•SentNote: See Status Icons on page 19 for more details on the TMS icons and TMS Menu Options on page 20 for more details on each menu option.Accessing TMS FeatureNote: If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Press the Menu Select button directly below BACK at any time to return to the previous screen.Procedure:Press the preprogrammed Data Feature button or the TMS button to access the TMS feature screen.ORPress and hold the preprogrammed Data Feature button or the TMS button to access the Inbox screen.ORFollow the procedure below.1> or < to TMS.2Press the Menu Select button directly below TMS to access the TMS feature screen.3> or < to scroll through the main menu options.O5Head_6875947M01_C.book Page 63 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish64Composing and Sending a New Text MessageNote: During the uppercase and lowercase mode, multi-tapping the keys only scrolls through the letters. For example, A->B->C, a->b->c. During the num lock mode, except for 1, pressing the keypad only enters the numeric digits. Subsequent presses of the same key inserts the same digit to the text message (no multi-tap).Procedure:1> or < to TMS.2Press the Menu Select button directly below TMS to access the TMS feature screen.3Press the Menu Select button directly below COMP to see the compose options.4Press the Menu Select button directly below NEW to compose a new message.5A blinking cursor appears on the Compose screen.Use the keypad to type or edit your message.Press < to move one space to the left. Press > to move one space to the right.Press the Menu Select button directly below DEL to delete any unwanted characters.Press * to add a space.Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode.Press # to toggle between numeric and letter mode.6Press the Menu Select button directly below OPTN once the message is composed.7> or < to SEND and press the Menu Select button directly below SEND to send.OR> or < to BACK and press the Menu Select button directly below BACK to return to Compose screen if you want to edit the message.8> or < to scroll through the address list and press the Menu Select button below SEL to select the required address.OR> or < to {OTHER RECPNT} and press the Menu Select button below EDIT.A blinking cursor appears in the ENTER ADDRESS screen.Use the keypad to type the address entry. Press < to move one space to the left. Press > to move one space to the right.Press the Menu Select button below DEL to delete any unwanted characters.Press * to add a space.Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode.Press # to toggle between numeric and letter mode.O5Head_6875947M01_C.book Page 64 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish659Press the Menu Select button below SEND to send the message.ORPress the PTT button to send the message.10 The display shows the SEND MESSAGE screen and SENDING MSG.11 If the message is sent, a tone sounds and the display shows MSG SENT.ORIf the message is not sent, a low tone sounds and the display shows SEND FAILED.If the message fails to send, the radio returns you to the main TMS screen.Note: You can append a priority status and/or a request reply to your message. See Using the Priority Status and Request Reply Features on page 67 for more information. Note: You can also select the DRFT option to save your message in the Drafts folder to send it at a later time. See Accessing the Drafts Folder on page 71 for more details.Sending a Quick Text MessageQuick Text messages are messages that are predefined and usually consist of messages that are used most frequently.Each Quick Text message has a maximum length of 50 characters.Procedure:Press the preprogrammed Quick Text button and proceed to Step 3.ORFollow the procedure below.1> or < to TMS.2Press the Menu Select button directly below TMS to access the TMS feature screen.3Press the Menu Select button directly below COMP to access the compose options.4> or < to LIST. 5> or < to scroll through the list of messages and press the Menu Select button directly below SEL to select the required message.6The message appears on the Compose screen, with a blinking cursor at the end of it.Use the keypad to edit the message. Press < to move one space to the left. O5Head_6875947M01_C.book Page 65 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish66Press > to move one space to the right.Press the Menu Select button directly below DEL to delete any unwanted characters.Press * to add a space.Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode.Press # to toggle between numeric and letter mode.7Press the Menu Select button directly below OPTN.8> or < to SEND and press the Menu Select button directly below SEL to send the message.9> or < to scroll through the address list and highlight the required address.OR> or < to {OTHER RECPNT} and press the Menu Select button below EDIT.A blinking cursor appears in the ENTER ADDRESS screen.Use the keypad to type the address entry. Press < to move one space to the left. Press > to move one space to the right.Press the Menu Select button below DEL to delete any unwanted characters.Press * to add a space.Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode.Press # to toggle between numeric and letter mode.10 Press the Menu Select button below SEND to send the message.ORPress the PTT button to send the message.11 The display shows the screen and SENDING MSG.12 If the message is sent, a tone sounds and the display shows MSG SENT.ORIf the message is not sent, a low tone sounds and the display shows SEND FAILED.If the message fails to send, the radio returns you to the main TMS screen.Note: You can append a priority status and/or a request reply to your message. See Using the Priority Status and Request Reply Features on page 67 for more information.O5Head_6875947M01_C.book Page 66 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish67Using the Priority Status and Request Reply FeaturesBefore sending your message, you can append a priority message and/or a request reply to your message.Appending or Removing a Priority Status to a Text MessageNote: The Priority Message icon on a message does not imply that the message gets higher priority over the other messages when it is being transmitted. It is just an indication that can be embedded into a message to let the receiver know that the message is important.Procedure:After the outgoing message is composed (see Composing and Sending a New Text Message on page 64 for more information):1Press the Menu Select button directly below OPTN.2Press the Menu Select button directly below IMPT. The priority status icon appears beside the normal message icon on the label bar.3Press the Menu Select button directly below IMPT again. The priority status icon and the normal message icon disappear from the label bar.Appending or Removing a Request Reply to a Text MessageProcedure:After the outgoing message is composed (see Composing and Sending a New Text Message on page 64 for more information):1Press the Menu Select button directly below OPTN.2Press the Menu Select button directly below RQRP. The reply status icon appears beside the normal message icon on the label bar.3Press the Menu Select button directly below RQRP again. The reply status icon and the normal message icon disappear from the label bar.Appending a Priority Status and a Reply Request to a Text MessageProcedure:After the outgoing message is composed (see Composing and Sending a New Text Message on page 64 for more information):1Press the Menu Select button directly below OPTN.2> or < to IMPT and press the Menu Select button directly below IMPT to indicate the message as important.ANDO5Head_6875947M01_C.book Page 67 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish68> or < to RQRP and press the Menu Select button directly below RQRP to request for a reply.3The priority status and reply status icons appear beside the normal message icon on the label bar.Removing a Priority Status and a Reply Request from a Text MessageWhen an outgoing message is indicated with priority status and reply status icons, follow the procedure below to remove these indicators.Procedure:1Press the Menu Select button directly below OPTN.2> or < to IMPT and press the Menu Select button directly below IMPT to remove the priority status icon.AND> or < to RQRP and press the Menu Select button directly below RQRP to remove the reply status icon.3The priority status, reply status and normal message icons disappear from the label bar.Managing Text MessagesReceiving a Text MessageNote: When you receive a message that is flagged with the ”Request Reply” icon, you must manually respond to the sender that you have received the message. The system will not automatically send back a notification that the radio has received such message.Procedure:When you receive a message, press and hold the preprogrammed Data Feature button or the TMS Feature button to access the Inbox and go to Step3.ORFollow the procedure below.1The new message icon appears and the display momentarily shows NEW MSG.2Press the Menu Select button directly below TMS to access the message.3The display shows alias or ID with the sender of the latest received message on top.O5Head_6875947M01_C.book Page 68 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish69Viewing a Text Message from the InboxThe Inbox can hold up to thirty (30) messages. Note: > or < to read the message if fills more than one screen.Procedure:Press the preprogrammed Data Feature button or the TMS Feature button to access the TMS feature screen, and proceed to Step 3.ORPress and hold the preprogrammed Data Feature button or the TMS Feature button to access the Inbox screen and proceed to Step 4.ORFollow the procedure below.1> or < to TMS.2Press the Menu Select button directly below TMS to access the TMS feature screen.3Press the Menu Select button below INBX to view Inbox feature screen.4The display shows alias or IDs, with the sender of the latest received message.While on the review message screen, press the Menu Select button directly below RPLY, DEL, or BACK to access the option.•Select RPLY to reply the message.•Select DEL to delete the message.•Select BACK to return to the previous screen.Note: The icon at the top right corner of the screen indicates the status of the message. See Text Messaging Service (TMS) on page 63 for more information.O5Head_6875947M01_C.book Page 69 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish70Replying to a Received Text MessageNote: The original date and time stamp, address and message content is automatically appended to the reply message.Procedure:1> or < to the required aliases or ID and press the Menu Select button below SEL to view the message.2Press the Menu Select button directly below RPLY to reply to a message.3> or < to NEW and press the Menu Select button directly below NEW.OR> or < to LIST and press the Menu Select button directly below LIST for a predefined message.OR> or < to scroll through the list of messages and press the Menu Select button directly below SEL to select the required message.4A blinking cursor appears on the screen.ORThe predefined message appears on the Compose screen, with a blinking cursor at the end of it.5Use the keypad to type or edit your message.Press < to move one space to the left. Press > to move one space to the right.Press the Menu Select button below DEL to delete any unwanted characters.Press * to add a space.Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode.Press # to toggle between numeric and letter mode.6Press the Menu Select button directly below OPTN once you have finished writing the message.7> or < to SEND and press the Menu Select button directly below SEND to send the message.8The display shows the Send Message screen and SENDING MSG.Press the Menu Select button directly below BACK at any time to return to the previous screen.Note: You can append a priority message and/or a request reply to your message. Using the Priority Status and Request Reply Features on page 67 for more information.O5Head_6875947M01_C.book Page 70 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish71Accessing the Drafts FolderThis folder stores the messages that were saved previously. The Drafts folder can hold up to 10 messages. The oldest draft in the folder is deleted when the 11th message comes in.Procedure:1> or < to TMS.2Press the Menu Select button directly below TMS to access the TMS feature screen.3> or < to DRFT and press the Menu Select button below DRFT.4The display shows the first draft message.Press the Menu Select button directly below EDIT, DEL, or BACK to access the option.•Select EDIT to edit the message before sending it.•Select DEL to delete the message.•Select BACK to return to the previous screen.Managing Sent Text MessagesOnce a message is sent to another radio, it is saved in the Sent folder. The most recent sent text message is always added to the top of the Sent list.The Sent folder is capable of storing a maximum of ten (10) last sent messages. When the folder is full, the oldest text message in the folder is deleted when the 11th message comes in.Viewing a Sent Text MessageThe icon at the top right corner of the screen indicates the status of the message. See Text Messaging Service (TMS) on page 63 for more information.Procedure:Press the preprogrammed Data Feature button or the TMS Feature button to access the TMS feature screen, and proceed to Step 3.ORFollow the procedure below.1> or < to TMS.2Press the Menu Select button directly below TMS to access the TMS feature screen.3> or < to SENT and press the Menu Select button below SENT.O5Head_6875947M01_C.book Page 71 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish72Press the Menu Select button directly below OPTN, DEL, or BACK to access the option.•Select OPTN to send to the message.•Select DEL to delete the message.•Select BACK to return to the previous screen.Note: The icon at the top right corner of the screen indicates the status of the message. See Text Messaging Service (TMS) Icons on page 19 for more information.Sending a Sent Text MessageProcedure: 1Press the Menu Select button directly below OPTN while viewing the message.2> or < to SEND and press the Menu Select button directly below SEND to send the message.3> or < to scroll through the address list and highlight the required address.OR> or < to {OTHER RECPNT} and press the Menu Select button below EDIT.A blinking cursor appears in the ENTER ADDRESS screen.Use the keypad to type the address entry. Press < to move one space to the left. Press > to move one space to the right.Press the Menu Select button below DEL to delete any unwanted characters.Press * to add a space.Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode.Press # to toggle between numeric and letter mode.4Press the Menu Select button below SEND or the PTT button to send the message.5The display shows the Send Message screen and SENDING MSG.6Press the Menu Select button directly below BACK to return to the previous screen.Note: You can append a priority message and/or a request reply to your message. See Using the Priority Status and Request Reply Features on page 67 for more details.O5Head_6875947M01_C.book Page 72 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish73Deleting Text MessagesProcedure:From the Inbox, Draft, or Sent screen:1> or < to scroll through the messages.2Press the Menu Select button directly below DEL to view the delete options.3Press the Menu Select button directly below CURR to delete the current message.ORPress the Menu Select button directly below ALL to delete all the messages.Secure OperationsSecure radio operation provides the highest commercially available level of voice security on both trunked and conventional channels.Unlike other forms of security, Motorola digital encryption provides signaling that makes it virtually impossible for others to decode any part of an encrypted message.Managing EncryptionNote: Refer to the Key-Variable Loader (KVL) manual for equipment connections and setup.Loading a Single Encryption KeyProcedure:1Attach the KVL to your radio. Upon attaching the KVL, the radio display shows KEYLOADING. 2Press the Menu Select button below TARGET.3Press the Menu Select button below LOAD.4Press the Menu Select button below KEY. 5> or < to required key.6Press the Menu Select button below LOAD to load the key to your radio.O5Head_6875947M01_C.book Page 73 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish747When the key has been loaded successfully, the radio sounds a short tone for single-key radios.Loading the Group Encryption KeysProcedure:1Attach the KVL to your radio. 2Press the Menu Select button below TARGET.3Press the Menu Select button below LOAD.4Press the Menu Select button below GROUP. 5> or < to required group.6Press the Menu Select button below LOAD to load the key to your radio.7Your mobile radio display shows KEYLOADING when it is loading key(s) from KVL.8When the key has been loaded successfully, the radio sounds an alternating tone for multikey radios.Using the Multikey FeatureThis feature allows the radio to be equipped with different encryption keys and supports the DES-OFB algorithm.There are two types of multikey:•Conventional Multikey – The encryption keys can be tied (strapped), on a one-per-channel basis, through Customer Programming Software. In addition, you can have operator-selectable keys, operator-selectable keysets, and operator-selectable key erasure. If talkgroups are enabled in conventional, then the encryption keys are strapped to the talkgroups.•Trunked Multikey – If you use your radio for both conventional and trunked applications, you have to strap your encryption keys for trunking on a per-talkgroup or announcement-group basis. In addition, you may strap a different key to other features, such as dynamic regrouping, failsoft, or emergency talkgroup. You can have operator-selectable key erasure.O5Head_6875947M01_C.book Page 74 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish75Selecting an Encryption Key (Conventional Only)Procedure:1> or < to KEY.2Press the Menu Select button directly below KEY. The display shows the last user-selected and stored encryption key, and the available menu selections.3> or < to scroll through the encryption keys.ORUse the keypad to enter the number of the desired key.4Press the Menu Select button directly below SEL to save the newly selected key and return to the Home screen.ORPress H, the PTT button, or the Menu Select button directly below EXIT to exit.Note: If the selected key is erased, a momentary keyfail tone sounds and the display shows KEY FAIL.ORIf the selected key is not allowed, a momentary illegal key tone sounds and the display shows ILLEGAL KEY.Enabling Secure TransmissionProcedure: 1> or < to SEC and press the Menu Select button directly below SEC. The display shows m and the current key if multi-key has been enabled.2Monitor the mode to be sure it is not in use.3Press PTT button to transmit.Note: If the selected channel is preprogrammed for clear-only operation – when you press the PTT button, an invalid mode tone sounds and the display shows CLEAR TX only. The radio does not transmit until you disable the secure mode.Accessing the Secure Feature Procedure: 1> or < to SEC. 2Press and hold the Menu Select button directly below SEC to display Secure feature screen.3The display shows the Secure screen.O5Head_6875947M01_C.book Page 75 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish76Selecting a KeysetThis feature allows you to select one or more groups of several encryption keys from among the available keys stored in the radio. For example, you could have a group of three keys structured to one keyset, and another group of three different keys structured to another keyset; by changing keysets, you would automatically switch from one set of keys to the other. Every channel to which one of the original keys was tied now has the equivalent new key instead.Note: Press H, the PTT button, or the EXIT menu selection to exit this menu at any time without changing the keyset selection.Procedure:1> or < to KSET.2Press the Menu Select button directly below KSET. The display shows the last user-selected and stored keyset, and the available keyset menu selections.3> or < to scroll through the keysets.ORUse the keypad to enter the number of the desired keyset.4Press the Menu Select button directly below SEL to save the newly selected keyset.5The radio exits keyset selection and returns to the Home screen.Erasing the Selected Encryption KeysThis feature allows you to erase all or selected encryption keys.Procedure:1> or < to ERAS.2Press the Menu Select button directly below ERAS. The display shows the last user-selected and stored encryption key, and the available menu selections.3> or < to the desired encryption key.ORUse the keypad to enter the number of the desired key. 4Press the Menu Select button directly below ALL to delete all keys.ORPress the Menu Select button directly below SNGL to delete current shown key.ORPress the Menu Select button directly below ABRT to abort this screen and return to Home screen.O5Head_6875947M01_C.book Page 76 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish77Requesting an Over-the-Air Rekey This feature, also known as OTAR, allows the dispatcher to reprogram the encryption keys in the radio remotely. The dispatcher performs the rekey operation upon receiving a rekey request from the user.Procedure:1> or < to REKY.2Press the Menu Select button directly below REKY. 3Press the PTT button to send the rekey request.ORPress the PTT button again, or the H or Emergency button, to exit the feature and transmit in normal mode.4If the rekey operation fails, a bad-key tone sounds and the display shows REKEY FAIL.Note: The rekey operation failure indicates that your radio does not contain the Unique Shadow Key (USK). This key must be loaded into the radio with the key-variable loader (KVL) before the rekey request can be sent.Refer to your local key management supervisor for more information.MDC Over-the-Air Rekeying (OTAR) PageThis feature allows to view or define MDC Over-the-Air Rekeying (OTAR) features.It is applied only when operating in secure encrypted mode and only for conventional communications. In additional to Rekey Requests, OTAR transmissions include Delayed Acknowledgements, and Power-up Acknowledgements. Some of the options selected may also need to be set up at the Key Management Controller (KMC) site to work properly.Note: This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information.O5Head_6875947M01_C.book Page 77 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish78Hear ClearThere are two components of Hear Clear. 1Companding:Reduces the channel noise, e.g. OTA transmission, that is predominantly present in UHF2 and 900 MHz channel with the following features.•Compressor – reduces the background noise flow and the speech signal at transmitting radio.•Expander – expands the speech while the noise flow remains the same at receiving radio.2Random FM Noise Canceller (Flutter Fighter):Reduces the unwanted effects of random FM noise pulses caused by channel fading under high Signal-to-Noise (S/N) conditions such as in a moving in a transportation. The fading effects, heard as audio pops and clicks, are cancelled without affecting the desired audio signal. The Random FM Noise Canceller operates only in receive mode.Note: This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information.The Global Positioning System (GPS)This feature uses information from the Global Positioning System (GPS) satellites orbiting the Earth to determine the approximate geographical location of your radio, expressed as latitude and longitude. The availability and accuracy of this location information (and the amount of time that it takes to calculate it) varies depending on the environment in which you are using the GPS feature.For example, GPS location fixes are very difficult to obtain indoors, in covered locations, between high buildings, or in situations where you have not established a clear broad view of the sky.Understanding the GPS FeatureThe GPS technology uses radio signals from earth orbiting satellites, to establish the location co-ordinates, maximizing your view of clear unobstructed sky is essential for optimum performance.Where adequate signals from multiple satellites are not available (usually because you cannot establish a view of a wide area of the sky), the GPS feature of your radio will not work. Such situations include but are not limited to: •In underground locations•Inside of buildings, trains, or other covered vehiclesO5Head_6875947M01_C.book Page 78 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish79•Under any other metal or concrete roof or structure•Between tall buildings or under dense tree-cover•In temperature extremes outside the operating limits of your radioEven where location information can be calculated in such situations, it may take longer to do so, and your location estimate may not be as accurate. Therefore, in any emergency situation, always report your location to your dispatcher. Note: Even where adequate signals from multiple satellites are available, your GPS feature only provides an approximate location, usually within 20 meters from your actual location, but sometimes further away.Keep in mind that the accuracy of the location information and the time it takes to obtain it varies depending upon circumstances, particularly the ability to receive signals from an adequate number of satellites. Note: The satellites used by the GPS feature are controlled by the U.S. government and are subject to changes implemented in accordance with the Department of Defense GPS user policy and the Federal Radio Navigation Plan. These changes may affect the performance of the GPS feature on your radio.Enhancing GPS PerformanceSometimes, the GPS feature may be unable to complete a location calculation successfully. You then see a message indicating that your radio cannot connect to enough visible satellites.To maximize the ability of your radio to determine a fix, please note the following guidelines:•For your initial fix, hold the radio in the face position.•Stay in the open. The GPS feature works best where there is nothing between your radio and a large amount of open sky.The Outdoor Location Feature (Using GPS)This feature allows you to determine your current location using a location menu, as well as your current distance and bearing in relation to another location. Radio location may be requested and reported over-the-air.Your radio stores up to a maximum of sixty (60) programmable location coordinates, also known as waypoints. When the memory is full, the next waypoints automatically replaces the oldest waypoints in the radio.O5Head_6875947M01_C.book Page 79 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish80The radio also stores four (4) preprogrammed waypoints. These coordinates cannot be deleted. Note: If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit.Accessing the Outdoor Location FeatureNote: An ON menu key may be present on the location menu if it is preprogrammed by the dealer or system administrator.Procedure:1> or < to LOC.2Press the Menu Select button directly below LOC. The display shows LOCATION OFF <LATITUDE>. 3Press the Menu Select button directly below ON to turn on the GPS. The display shows PREVIOUS LOC <LATITUDE>. 4> or < to check the longitude, time and date of the last successful location fix.5Press the Menu Select button directly below RFSH to obtain a new location fix. 6The top line temporarily displays PLEASE WAIT while the new location is being determined.While the new location is being determined, the location signal can be a solid or blinking icon.7Once the location coordinates are fixed, the display shows the current latitude. Toggle to see the longitude, time and date.The location coordinates are updated automatically every five seconds while the location signal is present.Programmable Waypoints Preprogrammed WaypointsUser-configurable location coordinates.Fixed location coordinates:•Home•Emergency•Last Known Location•DestinationOnly the alias is editable, not the coordinates. The Home and Destination coordinates are editable.Coordinates can be deleted one at a time, or all at once. Coordinates cannot be deleted.O5Head_6875947M01_C.book Page 80 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish818Press the Menu Select button directly below EXIT to exit the feature and return to the main screen.ORPress H or the PTT button (if preprogrammed) to exit this menu.ORFollow the procedure below to turn off the GPS (This feature is enabled by a qualified radio technician.):1> or < to LOC.2Press the Menu Select button directly below LOC. The display shows PREVIOUS LOC <LATITUDE>. 3> or < to check the longitude, time and date of the last successful location fix.4Press the Menu Select button directly below OPTN.5> or < to TURN OFF GPS (if preprogrammed). 6Press the Menu Select button directly below SEL to turn off the GPS. The display shows LOCATION OFF.7Press the Menu Select button directly below EXIT to exit the feature and return to the main screen.ORPress H or the PTT button (if preprogrammed) to exit this menu.The radio also exits the menu if the emergency button is pressed. Saving a WaypointProcedure:While in the current location display:1Press the Menu Select button directly below OPTN.2> or < to SAVE AS WAYPT and press the Menu Select button directly below SEL. OR> or < to SAVE AS HOME and press the Menu Select button directly below SEL and proceed to Step 5.OR> or < to SAVE AS DEST. and press the Menu Select button directly below SEL and proceed to Step 5.3A blinking cursor appears in the screen. Use the keypad to type the alias via multi-tap. Press < to move one space to the left.Press > to move one space to the right.Press the Menu Select button below DEL to delete any unwanted characters.Press * to add a space.Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode.Press # to toggle between numeric and letter mode.O5Head_6875947M01_C.book Page 81 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish824Press the Menu Select button directly below OK once you are done.5The display shows SAVED AS <WAYPOINT NAME>.ORThe display shows SAVED AS HOME.ORThe display shows SAVED AS DEST..6Press H or the PTT button (if preprogrammed) to exit this menu.Viewing a Saved WaypointProcedure:While in the current location display:1Press the Menu Select button directly below OPTN. 2> or < to WAYPOINTS.3Press the Menu Select button directly below SEL. 4> or < to desired waypoint.5Press the Menu Select button directly below OPTN. The display shows VIEW.6Press the Menu Select button directly below SEL. 7> or < again to view longitude, time and date the waypoint was detected.8Press the Menu Select button directly below BACK to return to previous Waypoint screen.ORPress H or the PTT button (if preprogrammed) to exit this menu.O5Head_6875947M01_C.book Page 82 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish83Editing the Alias of a WaypointProcedure:While in the current location display:1Press the Menu Select button directly below OPTN. 2> or < to WAYPOINTS.3Press the Menu Select button directly below SEL. 4> or < to desired waypoints.5Press the Menu Select button directly below OPTN. 6> or < to EDIT NAME and press the Menu Select button directly below SEL. 7A blinking cursor appears in the Edit Name screen. Use the keypad to edit the alias. Press < to move one space to the left.Press > to move one space to the right.Press the Menu Select button below DEL to delete any unwanted characters.Press * to add a space.Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode.Press # to toggle between numeric and letter mode.8Press the Menu Select button directly below OK once you are done.OR Press the Menu Select button directly below CNCL to return to the Waypoints main screen.9The display shows <WAYPOINT NAME> UPDATED.10 Press H or the PTT button (if preprogrammed) to exit this menu.Editing the Coordinates of a WaypointProcedure:While in the current location display:1Press the Menu Select button directly below OPTN. 2> or < to WAYPOINTS and press the Menu Select button directly below SEL. 3> or < to desired waypoints.4Press the Menu Select button directly below OPTN. 5> or < to EDIT LOCATION and press the Menu Select button directly below SEL. 6The first number blinks. Press < to move to the previous number/coordinates.Press > to move to the next number/coordinates.Press U or D to change the North (N), South (S), East (E) or West (W) direction.O5Head_6875947M01_C.book Page 83 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish84Press the Menu Select button below EDIT to change the number/coordinates.7A blinking cursor appears in the EDIT LOCATION screen.Press < to move one space to the left.Press > to move one space to the right.Press the Menu Select button below Del to delete any unwanted characters.8Press the Menu Select button directly below OK once you are done.ORPress the Menu Select button directly below CNCL to return to the previous screen.9Press the Menu Select button directly below OK once you are done with the new coordinates.ORPress the Menu Select button directly below CNCL to return to the previous screen then skip to step 11.10 The display shows {HOME} UPDATED and the radio returns to the Waypoints main screen.ORThe display shows {DESTINATION} UPDATED and the radio returns to the Waypoints main screen.11 Press H or the PTT button (if preprogrammed) to exit this menu.Deleting a Single Saved WaypointProcedure:While in the current location display:1Press the Menu Select button directly below OPTN. 2> or < to WAYPOINTS.3Press the Menu Select button directly below SEL. 4> or < to desired waypoints.5Press the Menu Select button directly below OPTN. OR Press the Menu Select button directly below DEL and then skip to step 7.6> or < to DELETE and press the Menu Select button directly below SEL. 7The display shows <WAYPOINT NAME> CONFIRM DEL?.8Press the Menu Select button directly below YES to delete. The display shows <WAYPOINT NAME> DELETED.ORPress the Menu Select button directly below NO to return to previous Waypoint screen.9Press H or the PTT button (if preprogrammed) to exit this menu.O5Head_6875947M01_C.book Page 84 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish85Deleting All Saved WaypointsProcedure:1Press the Menu Select button directly below OPTN. 2> or < to WAYPOINTS and press the Menu Select button directly below SEL. 3> or < to desired waypoints and press the Menu Select button directly below OPTN. 4> or < to DELETE ALL and press the Menu Select button directly below SEL. 5The display shows ALL SAVED WAYP CONFIRM DEL?.6Press the Menu Select button directly below YES to delete. The display shows ALL SAVED WAYP DELETED.ORPress the Menu Select button directly below NO to return to previous Waypoint screen.7Press H or the PTT button (if preprogrammed) to exit this menu.Measuring the Distance and Bearing from a Saved WaypointProcedure:While in the current location display:1Press the Menu Select button directly below OPTN.2> or < to DIST FRM HERE and press the Menu Select button directly below SEL.3> or < to the required waypoint, and press the Menu Select button directly below SEL.4The display shows the distance and bearing from the current to the selected coordinates. 5Press the Menu Select button directly below BACK to return to the previous Waypoint screen.ORPress H or the PTT button (if preprogrammed) to exit this menu.O5Head_6875947M01_C.book Page 85 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish86Using the Location Feature While in Emergency ModeWhen the Emergency feature is activated by pressing the emergency button, the radio exits the Location menu and returns to the home (default) display so that you can see which channel the emergency signal is going out on.However, you may re-enter the Location menu while still in emergency mode, provided that Silent Emergency has not been activated.If you have turned Location off using the ON/OFF menu key, it automatically turns back on when Emergency is activated.If there is a solid location signal during Emergency, the current location and the location information received is saved as Emergency and Last Known Location waypoints, respectively.Trunking System ControlsUsing the Failsoft SystemThe failsoft system ensures continuous radio communications during a trunked system failure. If a trunking system fails completely, the radio goes into failsoft operation and automatically switches to its failsoft channel.The failsoft condition is indicated by a faint beeping tone every nine seconds (radio unsquelched) until the trunking system returns to normal operation.To continue, in Failsoft, to communicate with other talkgroups, refer to the following procedure.Procedure:1Rotate the Mode Knob to change to a different repeater frequency. 2Press the PTT button to talk, and release the button to listen.When the trunking system returns to normal operation, your radio automatically leaves failsoft operation and returns to trunked operation.O5Head_6875947M01_C.book Page 86 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish87Going Out-of-RangeOUT OF RANGE when your radio goes out of the range of the system, it can no longer lock onto a control channel.Procedure:1A low-pitched tone sounds.AND/ORThe display shows the currently selected zone/channel combination and OUT OF RANGE.2Your radio remains in this out-of-range condition until:It locks onto a control channel.ORIt locks onto a failsoft channel.OR It is turned off.SmartZone®The SmartZone® feature extends communications beyond the reach of a single-trunked site (antenna location) when operating in a SmartZone system. SmartZone units provide expanded wide-area coverage.SmartZone automatically switches the radio to a different site when the current site signal becomes unacceptable. This usually happens when the vehicle in which the radio is located is driven out of the range of one site, and into the range of another.Under normal conditions, a SmartZone-enabled radio functions invisibly to the operator. However, the operator does have some manual controls on the Control Head – the RSSI menu entry. This button can be used to check, or change, the SmartZone operation.Using Site Trunking FeatureIf the zone controller loses communication with any site, that site reverts to site trunking.The display shows the currently selected zone/channel combination and SITE TRUNKING.Note: When this occurs, you can communicate only with other radios within your trunking site.O5Head_6875947M01_C.book Page 87 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish88Locking and Unlocking a SiteThis feature allows your radio to lock onto a specific site and not roam among wide-area talkgroup sites. This feature should be used with caution, since it inhibits roaming to another site in a wide-area system.Procedure: Use the preprogrammed Site Lock/Unlock button to toggle the lock state between locked and unlocked.ORFollow the procedure below.1> or < to SITE.2Press the Menu Select button directly below SITE.3Press the Menu Select button directly below LOCK to lock the site. ORPress the Menu Select button directly below UNLK to unlock the site. 4The radio saves the new site lock state and returns to the Home screen.Viewing and Changing a SiteThis feature allows you to view the number of the current site or force your radio to change to a new one.Viewing the Current SiteProcedure:1Press the preprogrammed Site Search button.OR> or < to RSSI.2The display momentarily shows the name of the current site and its corresponding received signal strength indicator (RSSI).O5Head_6875947M01_C.book Page 88 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish89Changing the Current SiteProcedure:1Press and hold down the preprogrammed Site Search button.ORPress and hold down the Menu Select button directly below RSSI.2A tone sounds and the display momentarily shows SCANNING SITE.When the radio finds a new site, it returns to the Home screen.Trunked AnnouncementThe announcement capability allows you to make announcements to the entire user group, as well as monitor talkgroup calls and other announcements.Announcement calls are handled in two different ways, depending on the trunked central controller configuration. The two types are called ruthless and non-ruthless preemption.•Ruthless Preemption: When a ruthless preemption announcement call is initiated, the requesting radio begins transmitting immediately. All associated talkgroup calls taking place on other channels are immediately halted, and the radios are steered to the announcement call.Transmitting radios continue to transmit until the PTT button is released, at which time they also unmute for the announcement call. Individual calls (Private Conversation and telephone interconnect) are not affected.•Non-Ruthless Preemption: When a non-ruthless preemption announcement is initiated, the initiating unit receives a telephone-type busy tone, followed by a call back when all associated talkgroup conversations end. Once an announcement call is pending, any attempts by other users to initiate a talkgroup call will result in a telephone-type busy tone. These users will not receive a call back until the announcement call is complete.O5Head_6875947M01_C.book Page 89 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish90Initiating an AnnouncementIf your radio has been programmed to allow announcement calls: Procedure:1Press the Mode Knob to locate the announcement-group mode.2Press the microphone PTT button to initiate the announcement.Ignition Switch OptionsThis feature allows the user to select the radio’s functionality based on the Ignition State of the radio user’s vehicle. The available options are as follows.BlankThis option allows the user to power on and power off the radio through the Power button regardless of the Ignition’s current state. Tx InhibitThis option allows the user to power on and power off the radio through the Power button regardless of the Ignition’s current state. In addition, if the Ignition is not present, then all transmissions are inhibited. This includes receiving any Trunking dispatch communications since the radio will not affiliate with the Trunking systems. PTT Tx InhibitThis option allows the user to power on and power off the radio through the Power button regardless of the Ignition’s current state. In addition, if the Ignition is not present, then all PTT button transmissions are inhibited. However, the radio is able to affiliate with the Trunking systems. O5Head_6875947M01_C.book Page 90 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish91RequiredThis option allows the user to power on the radio only if the Ignition is present. The radio can be powered off either through Power button press or when Ignition is lost. In addition, the radio automatically powers on when the Ignition is present only if the radio was turned off due to the ignition being removed.This option allows the radio to power off when Inactivity Auto Power Off Timer expires, or, when Ignition Auto Power Off Timer expires.Soft Power OffThis option allows the user to power on the radio either through Power button presses or when the Ignition is detected. Meanwhile, if the Power button was pressed or the Ignition was removed, the radio will be turned off. This option allows the radio to power off when Inactivity Auto Power Off Timer expires, or, when Ignition Auto Power Off Timer expires.Ignition Only Power UpThis option allows the user to power on the radio only when Ignition is detected and will power off when it is removed. The radio does not power on or off with the Power button press.This option allows the radio to power off when Inactivity Auto Power Off Timer expires, or, when Ignition Auto Power Off Timer expires.Note: While "Ignition" is not present, the radio powers-off with a radio-user Power Off button / knob selection if the radio was powered-up with an Emergency Power Up footswitch-press or Ignition Auto Power Off timer is running.While "Ignition" is present, the radio powers-on with a radio-user Power On button / knob selection only if the radio was powered-down with Inactivity Auto Power Off timer.Emergency Power UpThis feature allows the user to power on the radio and automatically transmits an emergency mode transmission on personalities with emergency enabled, with the use of a footswitch. In addition, when the Ignition Switch option is set to either Tx Inhibit or PTT Tx Inhibit, this feature will not be available to the users.Press the footswitch to turn on the radio and launch Emergency. A tone sounds and the display shows Emergency.O5Head_6875947M01_C.book Page 91 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish92Auto Power Off TimerAuto Power Off feature powers off the radio when no user actions occur during a preprogrammed length of time. There two different version of Auto Power Off:Inactivity Auto Power Off Timer – This timer begins once the radio is power-on. While the timer is active any user interaction with the radio resets the timer.Ignition Auto Power Off Timer – This timer begins once the vehicle key is removed, when the voltage at the ignition sense is removed. While the timer is active any user interaction with the radio resets the timer. When the vehicle key is reapplied, the voltage at the ignition is reconnected, this timer is stopped.Although both Inactivity Auto Power Off and Ignition Auto Power Off can be enabled together, Ignition Auto Power Off timer is mutually exclusive with Inactivity Auto Power Off timer when both are enabled.During the last two minutes of the timer countdown, the radio generates continuous low tone and blinks POWERING OFF warning on the display until the timer expires or is reset. The radio automatically powers off after the timer expires. The duration of the timer is preprogrammed.UtilitiesViewing Recent Calls ListThis feature allows you to view the recent incoming and outgoing call information of the following call types:•Call Alert•Selective Call•Private Call•Phone Call (Outgoing only) Note: The radio can also be preprogrammed to log the radio IDs associated with incoming Dispatch Calls. Check with your dealer or system administrator for more information.Procedure:1> or < to RCNT. 2Press the Menu Select button directly below RCNT to access the Recent Calls feature screen.3> or < to scroll through the list. 4Press the Menu Select button directly below BACK to return to Home screen.ORPress H or the PTT button to return to the Home screen.O5Head_6875947M01_C.book Page 92 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish93If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit.Selecting the Power Level You can select the power level at which your radio transmits. The radio always turns on to the default setting.Note: This feature must be preprogrammed by a qualified radio technician.Settings: •Select LOW for a shorter transmitting distance and to conserve power.•Select HIGH for a longer transmitting distance.Procedure: Use the preprogrammed Transmit Power Level Switch to toggle transmit power level between high and low. ORFollow the procedure below.1> or < to PWR.2Press the Menu Select button directly below PWR. 3The display shows LOW POWER and the low power icon.ORThe display shows HIGH POWER and the high power icon.Selecting a Radio ProfileThis feature allows you to manually switch the visual and audio settings of the radio. The display, backlight, alert tones, and audio settings are defined according to the preprogrammed radio settings of each radio profile.Please refer to a qualified technician for more information.Note: If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit.Procedure: Use the preprogrammed Profile button and proceed to Step 3.ORFollow the procedure below.1> or < to PRFL.2Press the Menu Select button directly below PRFL to access the Profiles feature screen.3> or < to scroll through the menu selections.4Press the Menu Select button directly below SEL to select the required radio profile. O5Head_6875947M01_C.book Page 93 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish94ORPress the Menu Select button directly below EXIT to exit the screen without making any changes.5The radio returns to the Home screen. The profile name on the Home screen indicates the current selected radio profile.Controlling the Display BacklightYou can enable or disable the radio’s display backlight as needed, if poor light conditions make the display difficult to read.Depending on how your radio is preprogrammed, you can also maintain a minimum backlight level on the radio’s display.Procedure:Note: Press the DIM button to toggle the backlight on or off.ORPress any key of the keypad, the Menu Select or Menu Navigation buttons, or any programmable radio controls or buttons to turn the backlight on.Turning Keypad Tones On or OffYou can enable and disable keypad tones as needed.Procedure:Press the preprogrammed Keypad Mute button to turn the tones on or off.ORFollow the procedure below.1> or < to MUTE.2Press the Menu Select button directly below MUTE.3The display momentarily shows TONES OFF, indicating that the keypad tones are disabled. ORThe display momentarily shows TONES ON, and a short tone sounds, indicating that the keypad tones are enabled.O5Head_6875947M01_C.book Page 94 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish95Turning Voice Mute On or OffYou can enable and disable voice muting of the affiliated trunking talkgroup or selected conventional channel as needed.Procedure:Press the preprogrammed Voice Mute button to turn the feature on or off.ORFollow the procedure below.1> or < to VMUT.2Press the Menu Select button directly below VMUT.3The display momentarily shows VOICE MUTE OFF, and a short tone sounds, indicating that the feature is disabled. ORThe display momentarily shows VOICE MUTE ON, and a short tone sounds, indicating that the feature is enabled.Using the Time-Out TimerThis feature turns off your radio’s transmitter. You cannot transmit longer than the preset timer setting.If you attempt to do so, the radio automatically stops your transmission, and you hear a talk-prohibit tone. The timer is defaulted at 60 seconds, but it can be preprogrammed from 3 to 120 seconds, in 15-second intervals, or it can be disabled entirely for each radio mode, by a qualified radio technician.Note: You will hear a brief, low-pitched, warning tone four seconds before the transmission times out.Procedure: 1Hold down the PTT button longer than the preprogrammed time. You hear a short, low-pitched warning tone, the transmission is cut-off, and the LEDs goes out until you release the PTT button.2Release the PTT button. The LEDs relight and the timer resets.3Press the PTT button to re-transmit. The time-out timer restarts and the red LED lights up.O5Head_6875947M01_C.book Page 95 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish96Using the Conventional Squelch Operation FeaturesThis feature filters out unwanted calls with low signal strength or channels that have a higher than normal background noise.1Procedure: > or < to SQL.2Press the Menu Select button directly below SQL. The display shows SQUELCH XX, where XX is the value for the current squelch.3Press the Menu Select button directly below “+” to increase the squelch volume.ORPress the Menu Select button directly below “-” to decrease the squelch volume.4Press H to return to the selected channel.Analog OptionsTone Private Line (PL), Digital Private-Line (DPL), and carrier squelch can be available (preprogrammed) per channel. Digital OptionsOne or more of the following options may be preprogrammed in your radio. Consult your dealer or system administrator for more information.Option ResultCarrier squelch (C) You hear all traffic on a channel.PL or DPL The radio responds only to your messages.Option ResultDigital Carrier-OperatedSquelch (COS)You hear any digital traffic.Normal Squelch You hear any digital traffic having the correct network access code.Selective Switch You hear any digital traffic having the correct network access code and correct talkgroup.O5Head_6875947M01_C.book Page 96 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish97Using the PL Defeat FeatureThis feature allows you to override any coded squelch (DPL or PL) that might be preprogrammed to a channel. The radio also unmutes to any digital activity on a digital channel.Procedure:Place the preprogrammed PL Defeat switch in the PL Defeat position. You hear any activity on the channel.OR The radio is muted if no activity is present.Note: When this feature is active, the Carrier Squelch status indicator is displayed.Using the Digital PTT ID FeatureThis feature allows you to the radio ID (number) of the radio from whom you are currently receiving a transmission. This ID, consisting up to a maximum of eight characters, can be viewed by both the receiving radio and the dispatcher.Your radio’s ID number is also automatically sent every time the PTT button is pressed. This is a per-channel feature. For digital voice transmissions, your radio’s ID is sent continuously during the voice message.Using the Smart PTT Feature (Conventional Only)Smart PTT is a per-personality, programmable feature used in conventional radio systems to keep radio users from talking over other radio conversations.When smart PTT is enabled in your radio, you cannot transmit on an active channel.If you try to transmit on an active smart-PTT channel, you hear an alert tone, and the transmission is inhibited. The LED lights up solid yellow to indicate that the channel is busy.Three variations of smart PTT are available:Mode DescriptionTransmit Inhibit on Busy Channel with CarrierYou cannot transmit if any traffic is detected on the channel.Transmit Inhibit on Busy Channel with Wrong Squelch CodeYou cannot transmit on an active channel with a squelch code or (if secure-equipped) encryption key other than your own. If the PL code is the same as yours, the transmission is not prevented.Quick-Key Override This feature can work in conjunction with either of the two above variations. You can override the transmit-inhibit state by quick-keying the radio. In other words, two PTT button presses within the preprogrammed time limit.O5Head_6875947M01_C.book Page 97 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish98Accessing General Radio InformationYour radio contains information on the following:•Radio Information•IP Display•Control AssignmentsNote: If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit.Accessing Radio InformationThis feature displays the following information of your radio: Note: Press H at any time to return to the Home screen.Procedure:1> or < to INFO.2Press the Menu Select button directly below INFO. 3> or < to RADIO INFO and press the Menu Select button directly below SEL. 4The display shows the Information screen.5> or < to scroll through the various information.ORPress the Menu Select button directly below BACK to return to previous screen. ORPress H to exit and return to the home display.•Host Version •DSP Version•Secure Version •KG (Secure Algorithm)•CH 1 – 4 Version (depending on the number of channels connected.)•Serial Number•MCHIB Version•CHIB Version•AUX CH Version•TIB Version •Siren Version•TRC Version •VRS Version•URC Version •DVRS App Version (only when DVRS is available)•DVRS DSP Version (only when DVRS is available) •DVRS CP Version (only when DVRS is available)•Model Number •Serial Number•ESN •Flash Size & Type•Flash Code •RF Band•Tuning Version •Processor VersionO5Head_6875947M01_C.book Page 98 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish99Viewing IP InformationThis feature displays the device name, IP address, and status of your radio.Note: The device name of your radio is preprogrammed. Check with your dealer or system administrator for more information.Procedure:Press the preprogrammed Info button and proceed to Step 3.ORFollow the procedure below.1> or < to INFO. 2Press the Menu Select button directly below INFO.3> or < to IP INFO and press the Menu Select button directly below SEL. 4> or < to scroll through the various information.ORPress the Menu Select button directly below BACK to return to previous screen. ORPress H to exit and return to the Home display.Viewing Control AssignmentsThis feature displays the programmable radio functions assigned to the controls of your radio for the currently selected channel.See Programmable Features on page 7 for more information on the various programmable features of your radio.Procedure:1> or < to INFO.2Press the Menu Select button directly below INFO.3> or < to CONTROL MAP and press the Menu Select button directly below SEL. 4> or < to scroll through the various information.ORPress the Menu Select button directly below BACK to return to previous screen. ORPress H to exit and return to the Home display.O5Head_6875947M01_C.book Page 99 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish100Using Optional External Alarms (Horn and Lights)All control heads can be equipped for external alarms (horn and lights) that are activated when a Call Alert page, Private Conversation call, or phone call is received.The radio always powers up with the horn and lights feature enabled.Note: The horn and lights feature must be enabled by a qualified radio technician.Using Non-Permanent Horn and LightsProcedure:1Press the Menu Select button directly below H/L momentarily. The last selected alarm(s) are enabled, and the display shows the enabled alarm(s) alternating with the selected mode, until it is turned off.2Press the Menu Select button directly below H/L momentarily to turn off the alarm(s). The display shows HORN/LITES OFF.Using Permanent Horn and LightsIf Permanent Horn and Lights is enabled, horn and lights will automatically be turned on when the radio powers up.Procedure:1Press the Menu Select button directly below H/L once to turn off the alarm(s).2Press the Menu Select button directly below H/L momentarily to enable the last selected alarm(s). The display briefly shows the enabled alarms, and then reverts back to the selected mode.O5Head_6875947M01_C.book Page 100 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish101Changing the Selected AlarmsProcedure:1Press the Menu Select button directly below H/L until the display shows the required alarm.2Press the Menu Select button directly below the required entry and the display exits to Home screen.Press the Menu Select button directly below the entry activates the option. Below are the selections available.•Select H+L to turn on both horn and lights. The display shows HORN/LITES ON.•Select LGTS to turn on the lights. The display shows LIGHTS ON.•Select HORN to turn on the horn. The display shows HORN ON.An OFF entry is shown at the softkey when one of the features above is active. Selecting the OFF deactivates the current active alarm.Receiving a Call While Alarms are Turned OnWhen you receive a call with the Alarms turned on:Procedure:1You hear the vehicle’s horn sounds for four seconds, and/or the car lights turn on for 60 seconds.2The display shows the type of call received (CALL, PAGE, or PHONE) and the selected mode name.The time interval can be modified by a qualified radio technician.Turning Off Non-Rearmable External AlarmsProcedure:1Press the Menu Select button directly below CALL, PAGE or PHON will turn off the external alarm(s) and place you directly in that feature.ORPress the PTT button or any control-head button to turn off the external alarm(s). 2Press the Menu Select button directly below H/L momentarily to rearm the horn and lights feature.The Volume Knob and the DIM button have no effect on the state of the external alarm(s).O5Head_6875947M01_C.book Page 101 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish102Turning Off Rearmable External AlarmsProcedure:1Press the Menu Select button directly below CALL, PAGE or PHON to turn off the external alarm(s) and place you directly in that feature. The external alarm(s) is turned off and automatically rearmed so that when you exit the entry, the external alarm(s) will automatically turn on.ORPress the PTT button or any control head button other than the Menu Select button directly below H/L to turn off the external alarm(s). The external alarm(s) is turned off and automatically rearmed so that when you exit the entry, the external alarm(s) will automatically turn on.ORPress the Menu Select button directly below H/L to turn off the external alarm(s) and exit the Horn and Lights feature.Press the Menu Select button directly below H/L momentarily to rearm the horn and lights feature.The Volume knob and the DIM button have no effect on the state of the external alarms.Using the Voice AnnouncementThis feature enables the radio to audibly indicate the current feature mode, Zone or Channel the user has just assigned. This audio indicator can be customized per customer requirements. This is typically useful when the user is in a difficult condition to read the content shown on the display. Each voice announcement is within a limit of three seconds maximum. The sum total duration for all voice announcements in a radio shall be no more than 1000 seconds.Note: This feature must be preprogrammed by a qualified radio technician.The features which Voice Announcement supports are:•Zone•Channel•Scan•Monitor•Talkaround/Direct•Tx InhibitNote: Voice announcements support certain number of zone-channel, but not all. Seek advice from your dealer or qualified technician for the best selections for this feature.O5Head_6875947M01_C.book Page 102 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish103The two options of priority for the Voice Announcement available are:•High – enables the voice of the feature to announce even when the radio is receiving calls.•Low – disables the voice of the feature from announcing when the radio is receiving calls.Procedure:You hear a voice announcement when the features below are preprogrammed in the radio.•The radio powers up. The radio announces the current zone and channel it is transmitting.•Press the preprogrammed voice announcement button (which specifically programmed to playback the current zone and channel). The radio announces the current zone and channel it is transmitting.Note: Pressing this preprogrammed playback button will always enable the voice feature to announce in High priority.All the three programmable buttons at the side of the radio support this feature.•Change to a new zone. The radio announces the current zone and channel it is transmitting.•Change to a new channel within the current zone. The radio announces the current channel.•Press either the Menu Select button or preprogrammed button of the radio to launch or terminate Scan, Monitor, Talkaround/Direct or Transmit Inhibit. The radio announces the corresponding feature activation or deactivation. O5Head_6875947M01_C.book Page 103 Wednesday, October 20, 2010 12:13 PM
Advanced FeaturesEnglish104Helpful TipsThe following are suggestions to assist you in troubleshooting possible operating problems.If your radio is locked up or the display shows FAIL 01/09, turn the radio off and then back on. If this does not correct the condition, take the radio to a qualified radio technician for service.If radio operation is intermittent, check with other persons using the system for similar problems before taking the radio in for service. Similar problems indicate a system malfunction rather than a radio failure.If symptoms persist or, if your unit exhibits other problems, contact a qualified radio technician.The cables that connect to the rear of the radio could have live voltage on some of their pins. Do not remove or reconnect these cables. Only a qualified radio technician should perform this task. Service performed by unauthorized personnel may cause the radio to transmit an emergency alarm even if the unit is turned off.!O5Head_6875947M01_C.book Page 104 Wednesday, October 20, 2010 12:13 PM
AccessoriesEnglish105Accessories For a list of Motorola-approved antennas and other accessories, visit the following website: http://www.motorola.com/governmentandenterpriseOn the website, search for APX Mobile Radios. You will see the accessories information besides the specifications of the radio. You can also contact your dealer for details.O5Head_6875947M01_C.book Page 105 Wednesday, October 20, 2010 12:13 PM
Appendix: Maritime Radio Use in the VHF English106Appendix: Maritime Radio Use in the VHF Frequency RangeTake a moment to review the following:Special Channel Assignments. . . . . . . . . . . . . . . . . . page 106Operating Frequency Requirements. . . . . . . . . . . . . page 107Special Channel AssignmentsEmergency ChannelIf you are in imminent and grave danger at sea and require emergency assistance, use VHF Channel 16 to send a distress call to nearby vessels and the United States Coast Guard. Transmit the following information, in this order:1“MAYDAY, MAYDAY, MAYDAY.”2“THIS IS _____________________, CALL SIGN __________.”State the name of the vessel in distress 3 times, followed by the call sign or other identification of the vessel, stated 3 times.3Repeat “MAYDAY” and the name of the vessel.4“WE ARE LOCATED AT _______________________.” State the position of the vessel in distress, using any information that will help responders to locate you, e.g.:• latitude and longitude• bearing (state whether you are using true or magnetic north)• distance to a well-known landmark • vessel course, speed or destination 5 State the nature of the distress.6Specify what kind of assistance you need. 7State the number of persons on board and the number needing medical attention, if any. 8Mention any other information that would be helpful to responders, such as type of vessel, vessel length and/or tonnage, hull color, etc.9“OVER.” 10 Wait for a response. 11 If you do not receive an immediate response, remain by the radio and repeat the transmission at intervals until you receive a response. Be prepared to follow any instructions given to you.Non-Commercial Call ChannelFor non-commercial transmissions, such as fishing reports, rendezvous arrangements, repair scheduling, or berthing information, use VHF Channel 9.O5Head_6875947M01_C.book Page 106 Wednesday, October 20, 2010 12:13 PM
Appendix: Maritime Radio Use in the VHF English107Operating Frequency RequirementsA radio designated for shipboard use must comply with Federal Communications Commission Rule Part 80 as follows:• on ships subject to Part II of Title III of the Communications Act, the radio must be capable of operating on the 156.800 MHz frequency • on ships subject to the Safety Convention, the radio must be capable of operating:• in the simplex mode on the ship station transmitting frequencies specified in the 156.025 – 157.425 MHz frequency band, and• in the semiduplex mode on the two frequency channels specified in the table below.Note: Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters.Additional information about operating requirements in the Maritime Services can be obtained from the full text of FCC Rule Part 80 and from the US Coast Guard. Table A-1: VHF Marine Channel ListChannel NumberFrequency (MHz)Transmit Receive1 156.050 160.6502 156.100 160.700* 156.150 160.7504 156.200 160.8005 156.250 160.8506 156.300 –7 156.350 160.9508 156.400 –9 156.450 156.45010 156.500 156.50011 156.550 156.55012 156.600 156.60013** 156.650 156.65014 156.700 156.70015** 156.750 156.75016 156.800 156.80017** 156.850 156.85018 156.900 161.50019 156.950 161.55020 157.000 161.600* 157.050 161.65022 157.100 161.700* 157.150 161.750Table A-1: VHF Marine Channel List (Continued)Channel NumberFrequency (MHz)Transmit ReceiveO5Head_6875947M01_C.book Page 107 Wednesday, October 20, 2010 12:13 PM
Appendix: Maritime Radio Use in the VHF English108* Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters.** Low power (1 W) only*** Guard bandNote: A – in the Receive column indicates that the channel is transmit only.24 157.200 161.80025 157.250 161.85026 157.300 161.90027 157.350 161.95028 157.400 162.00060 156.025 160.625* 156.075 160.67562 156.125 160.72563 156.175 160.775* 156.225 160.82565 156.275 160.87566 156.325 160.92567** 156.375 156.37568 156.425 156.42569 156.475 156.47571 156.575 156.57572 156.625 –73 156.675 156.67574 156.725 156.72575 *** ***76 *** ***77** 156.875 –Table A-1: VHF Marine Channel List (Continued)Channel NumberFrequency (MHz)Transmit Receive78 156.925 161.52579 156.975 161.57580 157.025 161.625* 157.075 161.675* 157.125 161.725* 157.175 161.77584 157.225 161.82585 157.275 161.87586 157.325 161.92587 157.375 161.97588 157.425 162.025Table A-1: VHF Marine Channel List (Continued)Channel NumberFrequency (MHz)Transmit ReceiveO5Head_6875947M01_C.book Page 108 Wednesday, October 20, 2010 12:13 PM
GlossaryEnglish109GlossaryThis glossary is a list of specialized terms used in this manual. Term DefinitionACK Acknowledgment of communication.Active Channel A channel that has traffic on it.Analog Signal An RF signal that has a continuous nature rather than a pulsed or discrete nature.ARS Automatic Registration ServiceASTRO 25 Trunking Motorola standard for wireless digital trunked communications.ASTRO Conventional Motorola standard for wireless digital conventional communications.Autoscan A feature that allows the radio to automatically scan the members of a scan list.AUX CH Auxiliary Control HeadCall Alert Privately page an individual by sending an audible tone. Carrier SquelchFeature that responds to the presence of an RF carrier by opening or unmuting (turning on) a receiver’s audio circuit. A squelch circuit silences the radio when no signal is being received so that the user does not have to listen to “noise”. Central Controller A software-controlled, computer-driven device that receives and generates data for the trunked radios assigned to it. It monitors and directs the operations of the trunked repeaters.Channel A group of characteristics such as transmit/receive frequency pairs, radio parameters, and encryption encoding.CHIB Control Head Interface BoardControl ChannelIn a trunking system, one of the channels that is used to provide a continuous, two-way/data communications path between the central controller and all radios on the system.Conventional Typically refers to radio-to-radio communications, sometimes through a repeater (see Trunking).Conventional Scan List A scan list that includes only conventional channels.Term DefinitionO5Head_6875947M01_C.book Page 109 Wednesday, October 20, 2010 12:13 PM
GlossaryEnglish110CP CodeplugCursor A visual tracking marker (a blinking line) that indicates a location on the display.DeadlockDisplayed by the radio after three failed attempts to unlock the radio.The radio must be powered off and on prior to another attempt.Digital Private Line (DPL)A type of coded squelch using data bursts. Similar to PL except a digital code is used instead of a tone.Digital Signal An RF signal that has a pulsed, or discrete, nature, rather than a continuous nature. Dispatcher An individual who has radio system management duties.DSP Digital Signal ProcessingDynamic RegroupingA feature that allows the dispatcher to temporarily reassign selected radios to a single special channel so they can communicate with each other.ESN Electrical Serial NumberTerm DefinitionFailsoftA feature that allows communications to take place even though the central controller has failed. Each trunked repeater in the system transmits a data word informing every radio that the system has gone into failsoft.FCC Federal Communications Commission.FM Frequency ModulationHang Up Disconnect.Home screen The first display information after the radio completes its self test.KVL Key-variable loader: A device for loading encryption keys into the radio.LCD Liquid crystal displayLED Light-emitting diodeMenu EntryA software-activated feature shown at the bottom of the display – selection of these features is controlled by the g.MCHB Millennium Control Head BoardTerm DefinitionO5Head_6875947M01_C.book Page 110 Wednesday, October 20, 2010 12:13 PM
GlossaryEnglish111MonitorCheck channel activity through menu entries. If the channel is clear, you hear static. If the channel is in use, you hear conversation. It also serves as a way to check the volume level of the radio, since the radio “opens the squelch” when the monitor button is pressed.Multi-System Talkgroup Scan ListA scan list that can include both talkgroups (trunked) and channels (conventional).Network Access CodeNetwork Access Code (NAC) operates on digital channels to reduce voice channel interference between adjacent systems and sites.Non-Tactical/RevertThe user talks on a preprogrammed emergency channel. The emergency alarm is sent out on this same channel.OTAR Over-the-air rekeying.Page A one-way alert, with audio and/or display messages.Personality A set of unique features specific to a radio.PIN Personal Identification NumberPreprogrammed Refers to a software feature that has been activated by a qualified radio technician.Term DefinitionPrivate (Conversation) CallA feature that lets you have a private conversation with another radio user in the talkgroup.Private Line (PL)A sub-audible tone that is transmitted such that only receivers decoding the tone receives it.Programmable Refers to a radio control that can have a radio feature assigned to it.PTT Push-To-Talk – the PTT button engages the transmitter and puts the radio in transmit (send) operation when pressed.Radio Frequency (RF)The part of the general frequency spectrum between the audio and infrared light regions (about 10 kHz to 10,000,000 MHz).RepeaterA conventional radio feature, where you talk through a receive/transmit facility that re-transmits received signals, in order to improve communications range and coverage.Selective CallA feature that allows you to call a select individual, intended to provide privacy and to eliminate the annoyance of having to listen to conversations of no interest to you.Term DefinitionO5Head_6875947M01_C.book Page 111 Wednesday, October 20, 2010 12:13 PM
GlossaryEnglish112Selective Switch Any digital P25 traffic having the correct Network Access Code and the correct talkgroup.SquelchSpecial electronic circuitry, added to the receiver of a radio, that reduces, or cuts off, unwanted signals before they are heard in the speaker.Standby An operating condition whereby the radio’s speaker is muted but still continues to receive data.Status Calls Pre-defined text messages that allow the user to send a conditional message without talking.Tactical/Non-RevertThe user talks on the channel that was selected before the radio entered the emergency state.Talkaround Bypass a repeater and talk directly to another unit for easy local unit-to-unit communications.Talkgroup An organization or group of radio users who communicate with each other using the same communication path.TMS Text Messaging ServiceTerm DefinitionTrunking The automatic sharing of communications paths between a large number of users (see Conventional).Trunking Priority Monitor Scan ListA scan list that includes talkgroups that are all from the same trunking system.USK Unique Shadow KeyUTCCoordinated Universal Time. The international time standard (formerly Greenwich Mean Time, or GMT). Zero hours UTC is midnight in Greenwich, England, which is located at 0 degrees longitude. Everything east of Greenwich (up to 180 degrees) is later in time; everything west is earlier. There are 42 time authorities around the world that are constantly synchronizing with each other. Abbreviated as UTC (English backronym = Universal Time, Coordinated), it is also known as Zulu (Z) Time.Zone A grouping of channels.Term DefinitionO5Head_6875947M01_C.book Page 112 Wednesday, October 20, 2010 12:13 PM
Commercial Warranty and ServiceEnglish113Commercial Warranty and ServiceLimited WarrantyMOTOROLA COMMUNICATION PRODUCTSI. WHAT THIS WARRANTY COVERS AND FOR HOW LONG:MOTOROLA INC. (“MOTOROLA”) warrants the MOTOROLA manufactured Communication Products listed below (“Product”) against defects in material and workmanship under normal use and service for a period of time from the date of purchase as scheduled below:MOTOROLA, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it (with a new or reconditioned Product), or refund the purchase price of the Product during the warranty period provided it is returned in accordance with the terms of this warranty. Replaced parts or boards are warranted for the balance of the original applicable warranty period. All replaced parts of Product shall become the property of MOTOROLA.This express limited warranty is extended by MOTOROLA to the original end user purchaser only and is not assignable or transferable to any other party. This is the complete warranty for the Product manufactured by MOTOROLA. MOTOROLA assumes no obligations or liability for additions or modifications to this warranty unless made in writing and signed by an officer of MOTOROLA. Unless made in a separate agreement between MOTOROLA and the original end user purchaser, MOTOROLA does not warrant the installation, maintenance or service of the Product.MOTOROLA cannot be responsible in any way for any ancillary equipment not furnished by MOTOROLA which is attached to or used in connection with the Product, or for operation of the Product with any ancillary equipment, and all such equipment is expressly excluded from this warranty. Because each system which may use the Product is unique, MOTOROLA disclaims liability for range, coverage, or operation of the system as a whole under this warranty.II. GENERAL PROVISIONS:This warranty sets forth the full extent of MOTOROLA'S responsibilities regarding the Product. Repair, replacement or refund of the purchase price, at MOTOROLA’s option, is the exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. IN NO EVENT SHALL MOTOROLA BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR APX Mobile Radio One (1) YearProduct Accessories One (1) YearO5Head_6875947M01_C.book Page 113 Wednesday, October 20, 2010 12:13 PM
Commercial Warranty and ServiceEnglish114INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW.III. STATE LAW RIGHTS:SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY. This warranty gives specific legal rights, and there may be other rights which may vary from state to state.IV. HOW TO GET WARRANTY SERVICE:You must provide proof of purchase (bearing the date of purchase and Product item serial number) in order to receive warranty service and, also, deliver or send the Product item, transportation and insurance prepaid, to an authorized warranty service location. Warranty service will be provided by MOTOROLA through one of its authorized warranty service locations. If you first contact the company which sold you the Product (e.g., dealer or communication service provider), it can facilitate your obtaining warranty service. You can also call MOTOROLA at 1-800-927-2744 US/Canada.V. WHAT THIS WARRANTY DOES NOT COVER:A)Defects or damage resulting from use of the Product in other than its normal and customary manner.B)Defects or damage from misuse, accident, water, or neglect.C)Defects or damage from improper testing, operation, maintenance, installation, alteration, modification, or adjustment.D)Breakage or damage to antennas unless caused directly by defects in material workmanship.E)A Product subjected to unauthorized Product modifications, disassembles or repairs (including, without limitation, the addition to the Product of non-MOTOROLA supplied equipment) which adversely affect performance of the Product or interfere with MOTOROLA's normal warranty inspection and testing of the Product to verify any warranty claim.F) Product which has had the serial number removed or made illegible.G)Rechargeable batteries if:• any of the seals on the battery enclosure of cells are broken or show evidence of tampering.• the damage or defect is caused by charging or using the battery in equipment or service other than the Product for which it is specified.H)Freight costs to the repair depot.I) A Product which, due to illegal or unauthorized alteration of the software/firmware in the Product, does not function in accordance with MOTOROLA’s published specifications or the FCC certification labeling in effect for the Product at the time the Product was initially distributed from MOTOROLA.J) Scratches or other cosmetic damage to Product surfaces that does not affect the operation of the Product.K)Normal and customary wear and tear.O5Head_6875947M01_C.book Page 114 Wednesday, October 20, 2010 12:13 PM
Commercial Warranty and ServiceEnglish115VI. PATENT AND SOFTWARE PROVISIONS:MOTOROLA will defend, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a United States patent, and MOTOROLA will pay those costs and damages finally awarded against the end user purchaser in any such suit which are attributable to any such claim, but such defense and payments are conditioned on the following:A)that MOTOROLA will be notified promptly in writing by such purchaser of any notice of such claim;B)that MOTOROLA will have sole control of the defense of such suit and all negotiations for its settlement or compromise; andC)should the Product or parts become, or in MOTOROLA’s opinion be likely to become, the subject of a claim of infringement of a United States patent, that such purchaser will permit MOTOROLA, at its option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non-infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by MOTOROLA.MOTOROLA will have no liability with respect to any claim of patent infringement which is based upon the combination of the Product or parts furnished hereunder with software, apparatus or devices not furnished by MOTOROLA, nor will MOTOROLA have any liability for the use of ancillary equipment or software not furnished by MOTOROLA which is attached to or used in connection with the Product. The foregoing states the entire liability of MOTOROLA with respect to infringement of patents by the Product or any parts thereof.Laws in the United States and other countries preserve for MOTOROLA certain exclusive rights for copyrighted MOTOROLA software such as the exclusive rights to reproduce in copies and distribute copies of such MOTOROLA software. MOTOROLA software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modified in any way, or used to produce any derivative thereof. No other use including, without limitation, alteration, modification, reproduction, distribution, or reverse engineering of such MOTOROLA software or exercise of rights in such MOTOROLA software is permitted. No license is granted by implication, estoppel or otherwise under MOTOROLA patent rights or copyrights.VII. GOVERNING LAW:This Warranty is governed by the laws of the State of Illinois, U.S.A.O5Head_6875947M01_C.book Page 115 Wednesday, October 20, 2010 12:13 PM
Commercial Warranty and ServiceEnglish116SERVICEProper repair and maintenance procedures will assure efficient operation and long life for this product. A Motorola maintenance agreement will provide expert service to keep this and all other communication equipment in perfect operating condition. A nationwide service organization is provided by Motorola to support maintenance services. Through its maintenance and installation program, Motorola makes available the finest service to those desiring reliable, continuous communications on a contract basis. For a contract service agreement, please contact your nearest Motorola service or sales representative, or an authorized Motorola dealer.Express Service Plus (ESP) is an optional extended service coverage plan, which provides for the repair of this product for a period of three years from the date of shipment from the factory, or the date of delivery if purchased from an authorized Motorola two-way radio dealer. For more information about ESP, contact the Motorola Radio Support Center, 2204 Galvin Drive, Elgin, IL 60123, 1-800-227-6772.O5Head_6875947M01_C.book Page 116 Wednesday, October 20, 2010 12:13 PM
O5Head_6875947M01_C.book Page 119 Wednesday, October 20, 2010 12:13 PM
© 2009, 2010 by Motorola, Inc. All Rights Reserved. 09/101301 E. Algonquin Rd., Schaumburg, IL 60196-1078, U.S.A.Printed in the U.S.A.*6875947M01*6875947M01-CO5Head_6875947M01_C.book Page 120 Wednesday, October 20, 2010 12:13 PM

Navigation menu