Motorola Solutions 99FT3092 2-Way Portable Radio User Manual MainContent EN

Download:
Mirror Download [FCC.gov]
Document ID	1982373
Application ID	G5Vh0GUf1WDE1JA+ALPbpw==
Document Description	RF Safety Guide
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	190.4kB (2379981 bits)
Date Submitted	2013-06-04 00:00:00
Date Available	2013-06-04 00:00:00
Creation Date	2011-07-13 21:15:59
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2013-03-25 12:18:13
Document Title	MainContent_EN.fm
Document Creator	FrameMaker 8.0
Document Author:	BTM876

MainContent_EN.fm Page 1 Monday, March 25, 2013 12:16 PM
RF Energy Exposure and Product
Safety for Portable Two-Way Radios
ATTENTION!
BEFORE USING THIS RADIO, READ
THIS GUIDE WHICH CONTAINS
IMPORTANT OPERATING
INSTRUCTIONS FOR SAFE USAGE
AND RF ENERGY AWARENESS AND
CONTROL FOR COMPLIANCE WITH
APPLICABLE STANDARDS AND
REGULATIONS.
RF Energy Exposure Awareness and
Control Information and Operational
Instructions for Occupational Use
NOTICE: This radio is intended for use in
occupational/controlled conditions where
users have full knowledge of their exposure
and can exercise control over their exposure
to meet the occupational limits in FCC and
International standards. This radio device is
NOT authorized for general population
consumer use.
This two-way radio uses electromagnetic energy in
the radio frequency (RF) spectrum to provide
communications between two or more users over a
distance. It uses radio frequency (RF) energy or radio
waves to send and receive calls. RF energy is one
form of electromagnetic energy. Other forms include,
but are not limited to, sunlight and x-rays. RF energy,
however, should not be confused with these other
forms of electromagnetic energy, which when used
improperly, can cause biological damage. Very high
English
MainContent_EN.fm Page 2 Monday, March 25, 2013 12:16 PM
levels of x-rays, for example, can damage tissues and
genetic material.
Experts in science, engineering, medicine, health, and
industry work with organizations to develop standards
for safe exposure to RF energy. These standards
provide recommended levels of RF exposure for both
workers and the general public. These recommended
RF exposure levels include substantial margins of
protection.
All Motorola two-way radios are designed,
manufactured, and tested to ensure they meet
government-established RF exposure levels. In
addition, manufacturers also recommend specific
operating instructions to users of two-way radios.
These instructions are important because they inform
users about RF energy exposure and provide simple
procedures on how to control it.
Please refer to the following websites for more
information on what RF energy exposure is and how
to control your exposure to assure compliance with
established RF exposure limits:
http://www.fcc.gov/oet/rfsafety/rf-faqs.html
www.who.int/en/
www.motorolasolutions.com/rfhealth
English
MainContent_EN.fm Page 3 Monday, March 25, 2013 12:16 PM
Federal Communication Commission (FCC)
Regulations
When two-way radios are used as a consequence of
employment, the FCC requires users to be fully aware
of and able to control their exposure to meet
occupational requirements. Exposure awareness can
be facilitated by the use of a product label directing
users to specific user awareness information. Your
Motorola two-way radio has a RF Exposure Product
Label. Also, your Motorola user manual, or separate
safety booklet includes information and operating
instructions required to control your RF exposure and
to satisfy compliance requirements.
Compliance with RF Exposure Standards
Your Motorola two-way radio is designed and tested to
comply with a number of national and International
standards and guidelines (listed below) for human
exposure to radio frequency electromagnetic energy.
This radio complies with the IEEE (FCC) and
ICNIRP exposure limits for occupational/
controlled RF exposure environments at
operating duty factors of up to 50% talk-50% listen
and is approved for occupational use only. In
terms of measuring RF energy for compliance with
these exposure guidelines, your radio generates
measurable RF energy only while it is transmitting
(during talking), not when it is receiving (listening)
or in standby mode.
NOTE:
The approved batteries, supplied with this
radio, are rated for a 5-5-90 duty factor (5%
talk-5% listen-90% standby) even though this
radio complies with FCC occupational
exposure limits and may operate at duty
factors of up to 50% talk.
English
MainContent_EN.fm Page 4 Monday, March 25, 2013 12:16 PM
Your Motorola two-way radio complies with the
following RF energy exposure standards and
guidelines:
• United States Federal Communications
Commission (FCC), Code of Federal Regulations;
47 CFR et seq.
• FCC, OET Bulletin 65
• Institute of Electrical and Electronic Engineers
(IEEE) C95.1
• International Commission on Non-Ionizing
Radiation Protection (ICNIRP)
• Ministry of Health (Canada) Safety Code 6
• Industry Canada RSS-102
• Australian Communications Authority
Radiocommunications Standard et seq.
• ANATEL ANNEX to Resolution No. 303 et seq.
RF Exposure Compliance and Control
Guidelines and Operating Instructions for
Two-Way Radio Operations
To control your exposure and ensure compliance with
the occupational/controlled environment exposure
limits, always adhere to the following procedures.
• DO NOT remove the RF Exposure Label from the
device.
• User awareness instructions should accompany
device when transferred to other users.
English
MainContent_EN.fm Page 5 Monday, March 25, 2013 12:16 PM
Operating Instructions
• Transmit no more than the rated duty factor of 50%
of the time. To transmit (talk), push the Push-ToTalk (PTT) button. To receive calls, release the PTT
button. Transmitting 50% of the time, or less, is
important because this radio generates measurable
RF energy exposure only when transmitting (in
terms of measuring for standards compliance).
• Private Talk Position (XTS 4000 Only). When
placing or receiving a personal message, hold your
radio as you would a wireline/wireless telephone.
Speak directly into the microphone. Use the PTT as
in a normal two-way operation.
• Two-Way Radio Operation. In front of
the face, hold the radio in a vertical
position with the microphone (and
other parts of the radio including the
antenna) at least one inch (2.5
centimeters) away from the nose or
lips. Keeping the radio at a proper distance is
important to ensure compliance.
NOTE:
RF exposures decrease with increasing
distance from the antenna.
• Body Worn Operation. When worn on the body,
always place the radio in a Motorola-approved clip,
holder, holster, case, or body harness for this
product. Using approved body-worn accessories is
important because the use of non-Motorolaapproved accessories may result in exposure
levels, which exceed the occupational/controlled
environment RF exposure limits.
English
MainContent_EN.fm Page 6 Monday, March 25, 2013 12:16 PM
• Use only Motorola-approved supplied or
replacement antennas, batteries, and audio
accessories. Use of non-Motorola-approved
antennas, batteries, and accessories may exceed
the applicable RF exposure guidelines (IEEE,
ICNIRP or FCC).
• For a list of Motorola-approved accessories for your
radio model, visit the following website:
http://www.motorolasolutions.com
Electromagnetic Interference/
Compatibility
NOTE:
Nearly every electronic device is susceptible
to electromagnetic interference (EMI) if
inadequately shielded, designed, or
otherwise configured for electromagnetic
compatibility.
Facilities
To avoid electromagnetic interference and/or
compatibility conflicts, turn off your radio in any facility
where posted notices instruct you to do so. Hospitals
or health care facilities may be using equipment that is
sensitive to external RF energy.
Aircraft
When instructed to do so, turn off your radio when on
board an aircraft. Any use of a radio must be in
accordance with applicable regulations per airline
crew instructions.
English
MainContent_EN.fm Page 7 Monday, March 25, 2013 12:16 PM
Medical Devices
Pacemakers
The Advanced Medical Technology Association
(AdvaMed) recommends that a minimum separation
of 6 inches (15 centimeters) be maintained between a
handheld wireless radio and a pacemaker. These
recommendations are consistent with those of the
U.S. Food and Drug Administration.
Persons with pacemakers should:
• ALWAYS keep the radio more than 6 inches (15
centimeters) from their pacemaker when the radio
is turned ON.
• Not carry the radio in the breast pocket.
• Use the ear opposite the pacemaker to minimize
the potential for interference.
• Turn the radio OFF immediately if there is any
reason to suspect that interference is taking place.
Hearing Aids
Some digital wireless radios may interfere with some
hearing aids. In the event of such interference, you
may want to consult your hearing aid manufacturer to
discuss alternatives.
Other Medical Devices
If you use any other personal medical device, consult
the manufacturer of your device to determine if it is
adequately shielded from RF energy. Your physician
may be able to assist you in obtaining this information.
English
MainContent_EN.fm Page 8 Monday, March 25, 2013 12:16 PM
Use of Communication Devices While Driving
Always check the laws and regulations on the use of
radios in the areas where you drive.
• Give full attention to driving and to the road.
• Use hands-free operation, if available.
• Pull off the road and park before making or
answering a call, if driving conditions or regulations
so require.
Acoustic Safety
Exposure to loud noises from any source for extended
periods of time may temporarily or permanently affect
your hearing. The louder the radio's volume, the less
time is required before your hearing could be affected.
Hearing damage from loud noise is sometimes
undetectable at first and can have a cumulative effect.
To protect your hearing:
• Use the lowest volume necessary to do your job.
• Turn up the volume only if you are in noisy
surroundings.
• Turn down the volume before adding headset or
earpiece.
• Limit the amount of time you use headsets or
earpieces at high volume.
• When using the radio without a headset or
earpiece, do not place the radio's speaker directly
against your ear.
English
MainContent_EN.fm Page 9 Monday, March 25, 2013 12:16 PM
Operational Warnings
WARNING
For Vehicle With Air Bags:
Refer to vehicle manufacturer's
manual prior to installation of
electronic equipment to avoid
interference with air bag wiring.
DO NOT place a portable radio in
the area over an air bag or in the air
bag deployment area. Air bags
inflate with great force. If a portable
radio is placed in the air bag
deployment area and the air bag
inflates, the radio may be propelled
with great force and cause serious
injury to occupants of the vehicle.
Potentially Explosive Atmospheres
(Explosive atmospheres refers to
hazard classified locations that may
contain hazardous gas, vapors, or
dusts.)
Turn off your radio prior to entering
any area with a potentially explosive
atmosphere unless it is a portable
radio type especially qualified for
use in such areas as Intrinsically
Safe (for example, Factory Mutual,
CSA, UL, or CENELEC).
English
MainContent_EN.fm Page 10 Monday, March 25, 2013 12:16 PM
WARNING
DO NOT remove, install, or charge
batteries in such areas. Sparks in a
potentially explosive atmosphere
can cause an explosion or fire
resulting in bodily injury or even
death.
The areas with potentially explosive
atmospheres referred to above
include fueling areas such as below
decks on boats, fuel or chemical
transfer or storage facilities, and
areas where the air contains
chemicals or particles such as
grain, dust or metal powders. Areas
with potentially explosive
atmospheres are often, but not
always, posted.
Blasting Caps and Blasting Areas
To avoid possible interference with
blasting operations, turn off your
radio when you are near electrical
blasting caps, in a blasting area, or
in areas posted: "Turn off two-way
radio." Obey all signs and
instructions.
English
10
MainContent_EN.fm Page 11 Monday, March 25, 2013 12:16 PM
Operational Cautions
Antennas
DO NOT use any portable radio that has a
damaged antenna. If a damaged antenna
comes into contact with your skin, a minor
C a u t i o n burn can result.
Batteries
All batteries can cause property damage
and/or bodily injury, such as burns, if a
conductive material such as jewelry, keys,
or beaded chains touches exposed
terminals. The conductive material may
complete an electrical circuit (short circuit)
and become quite hot. Exercise care in
handling any charged battery, particularly
when placing it inside a pocket, purse, or
other container with metal objects.
Intrinsically Safe Radio Information
The Intrinsically safe approval unit refers to a product
that has been approved as intrinsically safe by an
approval agency (for example FM Approvals, CSA,
UL, or Cenelec) and certifies that a particular product
meets the Agency's applicable intrinsic safety
standards for specific types of hazardous classified
locations. A portable radio that has been approved for
intrinsic safety will have Approval label attached to the
radio to identify the unit as being Approved for
specified hazardous atmospheres. This label specifies
the hazardous Class/Division/Group along with the
11
English
MainContent_EN.fm Page 12 Monday, March 25, 2013 12:16 PM
part number of the battery that must be used. The
Intrinsically Safe Approval Label will be located on the
portable radio unit.
Operational Cautions for Intrinsic Safe
Equipment
• DO NOT operate radio communications
equipment in a hazardous atmosphere
unless it is a type especially qualified
(for example, FM, UL, CSA, or
Caution
CENELEC approved). An explosion or
fire may result.
• DO NOT operate a radio unit that has
been approved as intrinsically safe
product in a hazardous atmosphere if it
has been physically damaged (for
example, cracked housing). An
explosion or fire may result.
• DO NOT replace or charge batteries in
a hazardous atmosphere. Contact
sparking may occur while installing or
removing batteries and cause an
explosion or fire.
Warnings for Radios Approved as
Intrinsically Safe
Radios must ship from the Motorola manufacturing
facility with the hazardous atmosphere capability and
the intrinsic safety approval labelling (FM, UL, CSA,
CENELEC). Radios will not be upgraded to this
capability and labeled once they have been shipped
to the field.
English
12
MainContent_EN.fm Page 13 Monday, March 25, 2013 12:16 PM
A modification changes the unit’s hardware from its
original design configuration. Modifications can only
be made by the original product manufacturer.
• DO NOT replace or change
accessories in a hazardous
atmosphere. Contact sparking may
occur while installing or removing
WARNING
accessories and cause an explosion
or fire.
• Turn the radio off before removing or
installing a battery or accessory.
• DO NOT disassemble an intrinsically
safe product in any way that
exposes the internal circuits of the
unit.
• Failure to use an intrinsically safe
approved battery or Approved
accessories specifically approved
for the radio unit may result in the
dangerously unsafe condition of an
unapproved radio combination
being used in a hazardous location
• Unauthorized or incorrect
modification of the intrinsically safe
approved Product will negate the
approval rating of the product.
13
English
MainContent_EN.fm Page 14 Monday, March 25, 2013 12:16 PM
WARNING
• Incorrect repair or relabeling of any
intrinsically safe Agency-approved
radio could adversely affect the
Approval rating of the unit.
• Use of a radio that is not intrinsically
safe in a hazardous atmosphere
could result in serious injury or
death.
Repair
REPAIRS FOR MOTOROLA PRODUCTS
WITH INTRINSICALLY SAFE
APPROVAL ARE THE
RESPONSIBILITY OF THE USER.
W A R N I N G Repairs to a Motorola FM approved
radio product should only be done at a
location that has been FM audited
under the FM 3605 repairs and service
standard.
Contact Motorola for assistance
regarding repairs and service of
Motorola intrinsically safe equipment.
A repair constitutes something done internally to the
unit that would bring it back to its original condition.
Items not considered as repairs are those in which an
action is performed on a unit which does not require
the outer casing of the unit to be opened in a manner
that exposes the internal electrical circuits of the unit.
English
14
MainContent_EN.fm Page 15 Monday, March 25, 2013 12:16 PM
Do Not Substitute Options or Accessories
The Motorola communications equipment certified as
intrinsically safe by the approving agency, (FM, UL,
CSA, CENELEC) is tested as a complete system
which consists of the listed agency Approved
portable, Approved battery, and Approved
accessories or options, or both. This Approved
portable and battery combination must be strictly
observed. There must be no substitution of items,
even if the substitute has been previously Approved
with a different Motorola communications equipment
unit. Approved configurations are listed by the
Approving Agency (FM, UL, CSA, CENELEC).
The Intrinsically Safe Approval Label affixed to radio
refers to the intrinsically safe classification of that
radio product, and the approved batteries that can be
used with that system.
The manual PN referenced on the Intrinsically Safe
Approval Label identifies the approved Accessories
and or options that can be used with that portable
radio unit.
Using a non-Motorola-intrinsically-safe battery and or
accessory with the Motorola approved radio unit will
void the intrinsically safe approval of that radio unit.
15
English
MainContent_EN.fm Page 16 Monday, March 25, 2013 12:16 PM
CP200d Portable Radios Quick
Reference Guide
Radio Controls
NOTE:
Refer to User Guide for more details on your
radio's operations/features.
English
16
MainContent_EN.fm Page 17 Monday, March 25, 2013 12:16 PM
Record your radio’s programmable button functions in
the blanks provided. SP represents short press, LP
represents long press.
Antenna
Push-to-Talk (PTT) Button
Side Button 1 (Programmable)
SP: ____________LP: ___________
Side Button 2(Programmable)
SP: ___________ LP: ___________
Microphone
Speaker
LED Indicator
On/Off/Volume Control Knob
Channel Selector Knob
17
English
MainContent_EN.fm Page 18 Monday, March 25, 2013 12:16 PM
LED Indicator
Blinking red – Radio is transmitting at low battery
condition, receiving an emergency transmission, has
failed the self-test upon powering up, or has moved
out of range if radio is configured with Auto-Range
Transponder System.
Solid green – Radio is powering up or transmitting.
Also indicates full charge of the battery when
programmable button is pressed.
Blinking green – Radio is receiving a non-privacyenabled call or data, detecting activity over the air.
Double blinking green – Radio is receiving a
privacy-enabled call or data.
Solid yellow – Radio is monitoring a conventional
channel.
Blinking yellow – Radio is scanning for activity,
receiving a Call Alert.
Double blinking yellow – Indicates radio has yet to
respond to a group call alert, or radio is locked.
English
18
MainContent_EN.fm Page 19 Monday, March 25, 2013 12:16 PM
Charging the Battery
Your radio is powered by a Lithium-Ion (Li-lon) or
Nickel-Metal Hydride (NiMH) battery. To avoid
damage and comply with warranty terms, charge the
battery using a Motorola charger exactly as described
in the charger user guide. It is recommended your
radio remains powered off while charging.
Charge a new battery 14 to 16 hours before initial use
for best performance.
Attaching the Battery
Align the battery with the rails on the back of the radio.
Press the battery firmly, and slide upward until the
latch snaps into place. Slide battery latch into lock
position.
Battery Latch
19
English
MainContent_EN.fm Page 20 Monday, March 25, 2013 12:16 PM
To remove the battery, turn the radio off. Move the
battery latch into unlock position and hold, and slide
the battery down and off the rails.
Battery Latch
English
20
MainContent_EN.fm Page 21 Monday, March 25, 2013 12:16 PM
Attaching the Antenna
With the radio turned off, set the antenna in its
receptacle and turn clockwise.
Make sure that the antenna is tightened securely to
the radio.
To remove the antenna, turn the antenna
counterclockwise.
21
English
MainContent_EN.fm Page 22 Monday, March 25, 2013 12:16 PM
Attaching the Belt Clip
Align the grooves on the clip
with those on the battery and
press downward until you hear
a click.
To remove the clip, press the
belt clip tab away from the
battery. Using a key may be
helpful. Then slide the clip
upward and away from the
radio.
English
22
MainContent_EN.fm Page 23 Monday, March 25, 2013 12:16 PM
Powering Up the Radio
Rotate the On/Off/Volume Control Knob clockwise
until you hear a click. The LED lights up solid green.
If enabled, a brief tone sounds indication that the
power up test is successful.There is no power up tone
if the radio tones/alerts function is disabled.
If your radio does not power up, check your battery.
Make sure that it is charged and properly attached. If
your radio still does not power up, contact your dealer.
To turn off the radio, rotate the knob counterclockwise
until you hear a click.
Adjusting the Volume
To increase the volume, turn the On/Off Volume
Control Knob clockwise.
To decrease the volume, turn this knob
counterclockwise.
NOTE:
Your radio can be programmed to have a
minimum volume offset where the volume
level cannot be turned down fully. Check with
your dealer or system administrator for more
information.
23
English
MainContent_EN.fm Page 24 Monday, March 25, 2013 12:16 PM
Accessing the Radio from Password
1. Power up the radio.
2. You hear a continuous tone.
3. Use the Channel Selector Knob to enter the first
digit of the password.
4. Press Side Button 1 or 2 to enter each digit of the
remaining three digits of the password. You hear a
positive indicator tone for each Side Button press.
When the second digit of the password is entered,
your radio ignores any Channel Selector Knob
position change.
5. When the last digit of the four-digit password is
entered, your radio automatically checks the
validity of the password.
If the password is correct:
Your radio proceeds to power up. See Powering
Up the Radio on page 23.
OR
If the password is incorrect:
You hear a continuous tone. Repeat Steps 1 to 3.
OR
After the third incorrect password, your radio
enters into locked state. A tone sounds and the
LED double blinks yellow.
Selecting a Channel
Turn the programmed Channel Selector Knob to
select the channel.
English
24
MainContent_EN.fm Page 25 Monday, March 25, 2013 12:16 PM
Making a Group Call
1. Turn the Channel Selector Knob to select the
channel with the active group alias or ID.
OR
Press the programmed One Touch Access
button.
2. Hold the radio vertically 1 to 2 inches (2.5 to
5.0cm) from your mouth.
3. Press the PTT button to make the call. The LED
lights up solid green.
4. Wait for the Talk Permit Tone to finish (if enabled)
and speak clearly into the microphone.
OR
Wait for the PTT Sidetone to finish (if enabled)
and speak clearly into the microphone.
5. Release the PTT button to listen.When the target
radio responds, the LED blinks green.
6.
If the Channel Free Indication feature is
enabled, you will hear a short alert tone the
moment the target radio releases the PTT button,
indicating the channel is free for you to respond.
Press the PTT button to respond.
OR
If there is no voice activity for a predetermined
period of time, the call ends.
25
English
MainContent_EN.fm Page 26 Monday, March 25, 2013 12:16 PM
Making a Private Call
1. Turn the Channel Selector Knob to select the
channel with the active subscriber alias or ID.
OR
Press the programmed One Touch Access
button.
2. Hold the radio vertically 1 to 2 inches (2.5 to
5.0cm) from your mouth.
3. Press the PTT button to make the call. The LED
lights up solid green.
4. Wait for the Talk Permit Tone to finish (if enabled)
and speak clearly into the microphone.
5. Release the PTT button to listen. When the target
radio responds, the LED blinks green.
6. If the Channel Free Indication feature is enabled,
you will hear a short alert tone the moment the
target radio releases the PTT button, indicating the
channel is free for you to respond. Press the PTT
button to respond.
OR
If there is no voice activity for a predetermined
period of time, the call ends.
NOTE:
English
Indicates a conventional Digital
mode-only feature.
26
MainContent_EN.fm Page 27 Monday, March 25, 2013 12:16 PM
Making an All Call
1. Turn the Channel Selector Knob to select the
channel with the active All Call group alias or ID.
2. Hold the radio vertically 1 to 2 inches (2.5 to
5.0cm) from your mouth.
3. Press the PTT button to make the call. The LED
lights up solid green.
4. Wait for the Talk Permit Tone to finish (if enabled)
and speak clearly into the microphone.
OR
Wait for the PTT Sidetone to finish (if enabled)
and speak clearly into the microphone.
Users on the channel cannot respond to an All Call.
Making a Call Alert with the One
Touch Access Button
1. Press the programmed One Touch Access
button to make a Call Alert to the predefined ID.
2. The LED lights up solid green when your radio is
sending the Call Alert.
3. If the Call Alert acknowledgement is received, two
chirps sound.
OR
If the Call Alert acknowledgement is not received,
a low-pitched tone sounds.
27
English
MainContent_EN.fm Page 28 Monday, March 25, 2013 12:16 PM
Sending an Emergency Alarm
This feature allows you to send an Emergency Alarm,
a non-voice signal, which triggers an alert indication
on a group of radios.
1. Press the programmed Emergency On button.
2. The LED lights up solid green
3. When an Emergency Alarm acknowledgment is
received, the Emergency tone sounds and the
LED blinks green.
OR
If your radio does not receive an Emergency Alarm
acknowledgement, and after all retries have been
exhausted, a low-pitch tone sound.
4. Radio exits the Emergency Alarm mode.
NOTE:
English
Indicates a conventional Analog
mode-only feature.
28

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Page Mode                       : UseOutlines
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Create Date                     : 2011:07:13 21:15:59Z
Creator Tool                    : FrameMaker 8.0
Modify Date                     : 2013:03:25 12:18:13+08:00
Metadata Date                   : 2013:03:25 12:18:13+08:00
Format                          : application/pdf
Title                           : MainContent_EN.fm
Creator                         : BTM876
Document ID                     : uuid:e980937f-6f83-45fa-8d56-4b7e8f0a95f3
Instance ID                     : uuid:01e41717-bab7-42e7-b409-195535dea2c5
Page Count                      : 28
Author                          : BTM876

EXIF Metadata provided by EXIF.tools