Motorola Solutions 99FT5012 800/900 CSA PORTABLE RADIO User Manual Neo Display User Guide 1 2

Motorola Solutions, Inc. 800/900 CSA PORTABLE RADIO Neo Display User Guide 1 2

UserManual.wiki >

Motorola Solutions >

99FT5012 User Manual

Users Manual

Display PortableUser GuideXPRTM 6580 ISProfessional Digital Two-Way Radio System

Declaration of ConformityEnglishiiNote: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.NAG_LACR.book Page ii Monday, August 23, 2010 1:03 PM

ContentsEnglishiiiContentsThis User Guide contains all the information you need to use the MOTOTRBO XPR IS Series Portable Radios.Important Safety Information . . . . . . . . . . . . . . . . . . vProduct Safety and RF Exposure Compliance . . . vSoftware Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . vComputer Software Copyrights . . . . . . . . . . . . . . . viGetting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . . 1What Your Dealer/System Administrator Can Tell You . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Preparing Your Radio for Use . . . . . . . . . . . . . . . . . . 2Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . 2Attaching the Battery . . . . . . . . . . . . . . . . . . . . . . . . . 3Attaching the Antenna . . . . . . . . . . . . . . . . . . . . . . . . 3Attaching the Belt Clip . . . . . . . . . . . . . . . . . . . . . . . . 3Attaching the Universal Connector Cover (Dust Cover) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Powering Up the Radio . . . . . . . . . . . . . . . . . . . . . . . 4Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . 5Identifying Radio Controls . . . . . . . . . . . . . . . . . . . . 5Radio Controls You Will Be Using . . . . . . . . . . . . . . 6Programmable Buttons . . . . . . . . . . . . . . . . . . . . . . . 7Assignable Radio Functions . . . . . . . . . . . . . . . . . 7Assignable Settings or Utility Functions . . . . . . . . . 8Accessing the Programmed Functions . . . . . . . . . . . 8Using the Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Push-To-Talk (PTT) Button . . . . . . . . . . . . . . . . . . . 10Switching Between Conventional and Trunking Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Identifying Status Indicators . . . . . . . . . . . . . . . . . . 11Display Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Call Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Main Menu Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . 12In-Menu Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Audio Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Indicator Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Making and Receiving Calls . . . . . . . . . . . . . . . . . . 14Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Selecting a Radio Channel . . . . . . . . . . . . . . . . . . . 15Receiving and Responding to a Radio Call . . . . . . 15Receiving and Responding to a Group Call . . . . . 15Receiving and Responding to a Private Call . . . . 16Receiving and Responding to a Phone Call . . . . 17Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . 17Making a Call with the Channel Selector Knob . . 18NAG_LACR.book Page iii Monday, August 23, 2010 1:03 PM

ContentsEnglishivMaking a Group Call . . . . . . . . . . . . . . . . . . . . 18Making a Private Call . . . . . . . . . . . . . . . . . . . . 18Making an Enhanced Private Call . . . . . . . . . . 19Making a Phone Call . . . . . . . . . . . . . . . . . . . . 20Sending a Status Call . . . . . . . . . . . . . . . . . . . 20Using the Dynamic Regrouping Feature . . . . . 21Talkaround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Monitoring Features . . . . . . . . . . . . . . . . . . . . . . . . 23Monitoring a Channel . . . . . . . . . . . . . . . . . . . . . 23Permanent Monitor . . . . . . . . . . . . . . . . . . . . . . . 23Advanced Features . . . . . . . . . . . . . . . . . . . . . . . . . 24Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Viewing an Entry in the Scan List . . . . . . . . . . . . 24Editing the Scan List . . . . . . . . . . . . . . . . . . . . . . 25Adding a New Entry to the Scan List . . . . . . . . 25Deleting an Entry from the Scan List . . . . . . . . 25Setting and Editing Priority for an Entry in the Scan List . . . . . . . . . . . . . . . . . . . . 26Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Starting and Stopping Scan . . . . . . . . . . . . . . . . 27Responding to a Transmission During a Scan . . 27Deleting a Nuisance Channel . . . . . . . . . . . . . . . 28Restoring a Nuisance Channel . . . . . . . . . . . . . . 28Contacts Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 29Making a Private Call from Contacts . . . . . . . . . . 29Making a Private Call by Alias Search . . . . . . . . 30Call Indicator Settings . . . . . . . . . . . . . . . . . . . . . . 30Activating and Deactivating Call Ringers for Private Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Escalating Alarm Tone Volume . . . . . . . . . . . . . . 31Call Log Features . . . . . . . . . . . . . . . . . . . . . . . . . . 31Viewing Recent Calls . . . . . . . . . . . . . . . . . . . . . 31Storing an Alias or ID from the Received Call List . . . . . . . . . . . . . . . . . . . . . . . . 32Deleting a Call from a Call List . . . . . . . . . . . . . . 32Call Alert Operation . . . . . . . . . . . . . . . . . . . . . . . . 33Receiving and Acknowledging a Call Alert . . . . . 33Making a Call Alert from the Contacts List . . . . . 33Making a Call Alert with the One Touch Call Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Emergency Operation . . . . . . . . . . . . . . . . . . . . . . 34Receiving an Emergency Call . . . . . . . . . . . . . . . 35Receiving an Emergency Alarm . . . . . . . . . . . . . 35Receiving an Emergency Alarm with Call . . . . . . 35Sending an Emergency Call . . . . . . . . . . . . . . . . 36Sending an Emergency Alarm . . . . . . . . . . . . . . 36Sending an Emergency Alarm with Call . . . . . . . 37Sending an Emergency Alarm with Voice to Follow . . . . . . . . . . . . . . . . . . . . . . . . . . 38Reinitiating an Emergency Mode . . . . . . . . . . . . 39Exiting Emergency Mode . . . . . . . . . . . . . . . . . . 39Dual-Tone Multi Frequency (DTMF) . . . . . . . . . . . 40NAG_LACR.book Page iv Monday, August 23, 2010 1:03 PM

ContentsEnglishvTrunking System Controls . . . . . . . . . . . . . . . . . . . . 40Using the Failsoft System . . . . . . . . . . . . . . . . . . 40Going Out of Range . . . . . . . . . . . . . . . . . . . . . . . 40Using the Site Trunking Feature . . . . . . . . . . . . . 41Locking and Unlocking a Site . . . . . . . . . . . . . . . 41Viewing and Changing a Site . . . . . . . . . . . . . . . . 41Viewing and Changing a Site . . . . . . . . . . . . . . 41Changing the Current Site . . . . . . . . . . . . . . . . 42Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Locking and Unlocking the Keypad . . . . . . . . . . . 42Turning Keypad Tones On or Off . . . . . . . . . . . . . 43Setting the Squelch Level . . . . . . . . . . . . . . . . . . 43Setting the Power Level . . . . . . . . . . . . . . . . . . . . 44Controlling the Display Backlight . . . . . . . . . . . . . 44Turning the Radio Tones/Alerts On or Off . . . . . . 45Turning the Talk Permit Tone On or Off . . . . . . . 45Turning the LED Indicator On or Off . . . . . . . . . . 46Turning the Introduction Screen On or Off . . . . . . 46Accessing General Radio Information . . . . . . . . . 47Accessing the Battery Information . . . . . . . . . . 47Checking the Radio ID . . . . . . . . . . . . . . . . . . . 48Checking the Firmware Version . . . . . . . . . . . . 48Checking the Codeplug Version . . . . . . . . . . . . 48Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Carry Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Chargers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Remote Speaker Microphones . . . . . . . . . . . . . . . . 50Miscellaneous Accessories . . . . . . . . . . . . . . . . . . . 50Batteries and Chargers Warranty . . . . . . . . . . . . . . 51Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 52NAG_LACR.book Page v Monday, August 23, 2010 1:03 PM

Important Safety InformationEnglishviImportant Safety InformationProduct Safety and RF Exposure ComplianceATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed with your radio (Motorola Publication part number 6881095C98) to ensure compliance with RF energy exposure limits.Keep this User Guide and the Product Safety and RF Exposure booklet in a safe place and make them available to other operators in case the radio is passed on to other people.For a list of Motorola-approved antennas, batteries, and other accessories, visit the following website: http://www.motorola.com/governmentandenterpriseSoftware VersionAll the features described in the following sections are supported by the radio's software version R01.00.00 or later. See Checking the Firmware Version on page 48 to determine your radio's software version. Check with your dealer or system administrator for more details of all the features supported.Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio.!C a u t i o nNAG_LACR.book Page vi Monday, August 23, 2010 1:03 PM

Computer Software CopyrightsEnglishviiComputer Software CopyrightsThe Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied, reproduced, modified, reverse-engineered, or distributed in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive license to use that arises by operation of law in the sale of a product.The AMBE+2TM voice coding Technology embodied in this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use within this Communications Equipment. The user of this Technology is explicitly prohibited from attempting to decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable form. U.S. Pat. Nos. #5,870,405, #5,826,222, #5,754,974, #5,701,390, #5,715,365, #5,649,050, #5,630,011, #5,581,656, #5,517,511, #5,491,772, #5,247,579, #5,226,084 and #5,195,166.NAG_LACR.book Page vii Monday, August 23, 2010 1:03 PM

NotesEnglishviiiNotesNAG_LACR.book Page viii Monday, August 23, 2010 1:03 PM

Getting StartedEnglish1Getting StartedTake a moment to review the following:How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . . . . page 1What Your Dealer/System Administrator Can Tell You . page 1How to Use This GuideThis User Guide covers the basic operation of MOTOTRBO XPR 6580 IS.However, your dealer or system administrator may have customized your radio for your specific needs. Check with your dealer or system administrator for more information.Throughout this publication, a note is shown for Conventional mode and Trunking mode only features to differentiate the features according to the two modes.For features that are available in both Conventional and Trunking modes, no note is shown.What Your Dealer/System Administrator Can Tell YouYou can consult your dealer or system administrator about the following:•Is your radio programmed with any preset conventional channels?•Which buttons have been programmed to access other features?•What optional accessories may suit your needs?NAG_LACR.book Page 1 Monday, August 23, 2010 1:03 PM

Preparing Your Radio for UseEnglish2Preparing Your Radio for UseAssemble your radio by following these steps:Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2Attaching the Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . page 3Attaching the Antenna. . . . . . . . . . . . . . . . . . . . . . . . . . page 3Attaching the Belt Clip. . . . . . . . . . . . . . . . . . . . . . . . . . page 3Attaching the Universal Connector Cover (Dust Cover) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4Powering Up the Radio . . . . . . . . . . . . . . . . . . . . . . . . . page 4Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . page 5Charging the BatteryYour radio is powered by a Lithium-Ion (Li-lon) battery. To avoid damage and comply with warranty terms, charge the battery using a Motorola charger exactly as described in the charger user guide.If battery is attached to your radio, ensure that your radio is turned off before charging.Charge a new battery 14 to 16 hours before initial use for best performance.IMPORTANT:ALWAYS charge your IMPRES battery with the IMPRES charger. Using a conventional charger causes irrecoverable loss of IMPRES battery data. As a result, the battery functions as a non-IMPRES battery and cannot display the data on your radio. Additionally, it voids your IMPRES battery warranty, although the standard battery warranty still applies.Charge battery only in non-hazardous areas. After battery is charged, allow your radio to rest for at least, 3 minutes. See Batteries on page 49 for the available batteries.!C a u t i o nNAG_LACR.book Page 2 Monday, August 23, 2010 1:03 PM

Preparing Your Radio for UseEnglish3Attaching the BatteryAlign the battery with the rails on the back of the radio. Press the battery firmly, and slide upward until the latch snaps into place. Slide battery latch into lock position.To remove the battery, turn the radio off. Move the battery latch into unlock position and hold, and slide the battery down and off the rails.Attaching the AntennaWith the radio turned off, set the antenna in its receptacle and turn clockwise.To remove the antenna, turn the antenna counterclockwise. Make sure you turn off the radio and remove the universal connector cover first.Attaching the Belt ClipAlign the grooves on the clip with those on the battery and press downward until you hear a click.To remove the clip, press the belt clip tab away from the battery using a key. Then slide the clip upward and away from the radio.Do not change battery in gas and dust environment. Replace battery only in non-hazardous areas. See Batteries on page 49 for the available batteries.Battery Latch!C a u t i o nIf antenna needs to be replaced, ensure that only MOTOTRBO antennas are used. Neglecting this will damage your radio. See Antennas on page 49 for the available antenna.!C a u t i o nNAG_LACR.book Page 3 Monday, August 23, 2010 1:03 PM

Preparing Your Radio for UseEnglish4Attaching the Universal Connector Cover(Dust Cover)The universal connector is located on the antenna side of the radio. It is used to connect MOTOTRBO accessories to the radio.Place the universal connector cover loop over the attached antenna. Slide it all the way down to the base of the antenna.Insert the hooked end of the cover into the slots above the universal connector. Press downward on the cover to seat the lower tab properly into the RF connector.Turn the thumbscrew clockwise to secure the connector cover to the radio.To remove the universal connector cover, press down on the cover and turn the thumbscrew counterclockwise. Lift the cover up, slide the connector cover loop upwards, and remove it from the attached antenna.Replace the universal connector cover when the connector is not in use.Powering Up the RadioRotate the On/Off/Volume Control Knob clockwise until you hear a click. You see Motorola and MOTOTRBO (TM) on the radio’s display momentarily.The LED blinks green and the Home screen lights up if the backlight setting is set to turn on automatically.NOTE: The Home screen does not light up during a power-up if the LED indicator is disabled (see Turning the LED Indicator On or Off on page 46).A brief tone sounds, indicating that the power-up test is successful.NOTE: There is no power-up tone if the radio tones/alerts function is disabled (see Turning the Radio Tones/Alerts On or Off on page 45).If your radio does not power up, check your battery. Make sure that it is charged and properly attached. If your radio still does not power up, contact your dealer or system administrator.Universal Connector Cover(Dust Cover)LED IndicatorNAG_LACR.book Page 4 Monday, August 23, 2010 1:03 PM

Identifying Radio ControlsEnglish5To turn off the radio, rotate this knob counterclockwise until you hear a click. You see a brief Powering Down on the radio’s display.Adjusting the VolumeTo increase the volume, turn the On/Off/Volume Control Knob clockwise.To decrease the volume, turn this knob counterclockwise.Identifying Radio ControlsTake a moment to review the following:Radio Controls You Will Be Using . . . . . . . . . . . . . . . . . page 6Programmable Buttons . . . . . . . . . . . . . . . . . . . . . . . . . page 7Accessing the Programmed Functions . . . . . . . . . . . . .page 8Using the Keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 9Push-To-Talk (PTT) Button. . . . . . . . . . . . . . . . . . . . . .page 10Switching Between Conventional and Trunking Mode . page 10NAG_LACR.book Page 5 Monday, August 23, 2010 1:03 PM

Identifying Radio ControlsEnglish6Radio Controls You Will Be Using1131715141312876521916410Channel Selector KnobOn/Off/Volume Control KnobLED IndicatorSide Button 1*Push-to-Talk (PTT) ButtonMicrophoneSide Button 2*Side Button 3*Front Button P1*Front Button P2*KeypadMenu Navigation KeysDisplayUniversal Connector for AccessoriesSpeakerEmergency Button*Antenna* These buttons are programmable.1234567891011121314151617NAG_LACR.book Page 6 Monday, August 23, 2010 1:03 PM

Identifying Radio ControlsEnglish7Programmable ButtonsYour dealer or system administrator can program the programmable buttons as shortcuts to radio functions or preset channels/groups depending on the duration of a button press:•Press – Pressing and releasing rapidly.•Long press – Pressing and holding for the programmed duration (between 0.25 seconds and 3.75 seconds).•Hold down – Keeping the button pressed.Assignable Radio FunctionsBattery Indicator – Checks the battery charge status via the LED.Call* – Initiates a private call by keying in or selecting any subscriber ID and accepts incoming private calls.Call Alert* – Allows selection of radio ID number to initiate a call alert.Contacts – Provides direct access to the Contacts list.Emergency* – Depending on the programming, initiates or cancels an emergency alarm or call.Message Update* – Selects a message update to send to the dispatcher.Monitor** – Monitors a selected channel for activity.Nuisance Delete – Temporarily removes an unwanted channel from the scan list until the radio is powered off and on again, or the scan is turned off and on again.One Touch Call* – Directly initiates a predefined Message, Status, Private Call, Phone Call, or a Call Alert to a target radio.Permanent Monitor** – Monitors a selected channel for all radio traffic until function is turned off.Phone – Initiates a phone call by keying in or selecting any phone ID and accepts incoming phone calls.Repeater/Talkaround** – Toggles between using a repeater and communicating directly with another radio.Scan – Toggles scan on or off.Site Display* – Displays current site on the radio display.Site Lock On/Off* – Toggles the automatic site roam on or off in Smart Zone operation.Site Search* – Starts site search in SmartZone operation.Status Update* – Selects a status update to send to the dispatcher.Transmit Inhibit – Prevents transmission when enabled.Zone – Allows selection from a list of zones.* A trunking only feature** A conventional only featureNAG_LACR.book Page 7 Monday, August 23, 2010 1:03 PM

Identifying Radio ControlsEnglish8Assignable Settings or Utility FunctionsAll Tones/Alerts – Toggles all tones and alerts on or off.Backlight – Toggles display backlight and front panel buttons backlight on or off.Keypad Lock – Toggles keypad between locked and unlocked.Power Level – Toggles transmit power level between high and low.Squelch** – Toggles squelch level between tight and normal.* A trunking only feature** A conventional only featureAccessing the Programmed FunctionsYou can access various radio functions through one of the following ways:•A short or long press of the relevant programmable buttons.OR•Use the Menu Navigation Buttons as follows:1To access the menu, press the S button. Press the appropriate Menu Scroll button (Por Q) to access the menu functions.2To select a function or enter a sub-menu, press the N button.3To go back one menu level, or to return to the previous screen, press the R button. Long press the R button to return to the Home screen.NOTE: Your radio automatically exits the menu after a period of inactivity and returns to your Home screen. NAG_LACR.book Page 8 Monday, August 23, 2010 1:03 PM

Identifying Radio ControlsEnglish9Using the KeypadYou can use the 3 x 4 alphanumeric keypad to access your radio’s features. You can use the keypad to enter subscriber aliases or IDs. Many characters require that you press a key multiple times. The table below shows the number of times a key needs to be pressed to generate the required character.Number of Times Key is PressedKey1 234567891011121311.,?!@&‘%-:*#2ABC23DEF34GHI45JKL56MNO67PQRS78TUV89WXYZ900NOTE: Press to enter “0” and long press to activate the CAPS lock. Another long press to turn off the CAPS lock.** or del NOTE: Press during text entry to delete the character. Press during numeric entry to enter a “*”.## or space NOTE: Press during text entry to insert a space. Press during numeric entry to enter a “#”.NAG_LACR.book Page 9 Monday, August 23, 2010 1:03 PM

Identifying Radio ControlsEnglish10Push-To-Talk (PTT) ButtonThe PTT button on the side of the radio serves two basic purposes:•While a call is in progress, the PTT button allows the radio to transmit to other radios in the call.Press and hold down PTT button to talk. Release the PTT button to listen.The microphone is activated when the PTT button is pressed.•While a call is not in progress, the PTT button is used to make a new call (see Making a Radio Call on page 17).If the Talk Permit Tone is enabled (see Turning the Talk Permit Tone On or Off on page 45), wait until the short alert tone ends before talking.Switching Between Conventional and Trunking ModeEach channel in your radio can be configured as a conventional channel or a trunking channel. Use the Channel Selector Knob to switch between a conventional or a trunking channel.When switching from trunking to conventional mode, certain features are unavailable. Icons for the trunking features reflect this change by appearing “grayed out’. Disabled features are hidden in the menu.Your radio also has features available in both conventional and trunking mode. However, the minor differences in the way each feature works does NOT affect the performance of your radio.PTT ButtonChannel Selector KnobNAG_LACR.book Page 10 Monday, August 23, 2010 1:03 PM

Identifying Status IndicatorsEnglish11Identifying Status IndicatorsYour radio indicates its operational status through the following:Display Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 11Call Icons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 12Main Menu Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 12In-Menu Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 12LED Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 13Audio Tones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 13Indicator Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 13Display IconsThe full dot matrix, black and white, liquid crystal display (LCD) of your radio shows radio status, text entries, and menu entries.The following are icons that appear on the radio’s display.Received Signal Strength Indicator (RSSI)NOTE: This is a trunking only feature.The number of bars displayed represents the radio signal strength. Four bars indicate the strongest signal.MonitorNOTE: This is a conventional only feature.Selected channel is being monitored.Power LevelRadio is set at Low power.Radio is set at High power.Tones DisableTones are turned off.ScanScan feature is enabled. Priority ScanNOTE: This is a trunking only feature.Radio detects activity on channel/group designated as Priority 1 (if • is blinking) or Priority 2 (if • is steady).EmergencyNOTE: This is a trunking only feature.Radio is in Emergency mode.TalkaroundNOTE: This is a conventional only feature.In the absence of a repeater, radio is currently configured for direct radio to radio communication.BatteryThe number of bars (0 – 4) shown indicates the charge remaining in the battery.Blinks when the battery is low.orNAG_LACR.book Page 11 Monday, August 23, 2010 1:03 PM

Identifying Status IndicatorsEnglish12Call IconsThe following icons appear on the radio’s display during a call. These icons also appear in the Contacts list to indicate ID type.Main Menu IconsThe following are icons that appear on the radio’s display.In-Menu IconsThe following are icons that appear on the radio’s display.Private CallNOTE: This is a trunking only feature.Indicates a Private Call in progress. In the Contacts list, it indicates a subscriber alias (name) or ID (number).Dispatcher CallIndicates a Dispatcher Call in progress.Phone CallIndicates a Phone Call in progress.ContactsSelects the Contacts menu.ScanSelects the Scan menu.ZoneAllows selection from a list of zones.TMSSelects the Status and Message menu.Call LogSelects the Call Log menu.UtilitiesSelects the Utilities menu.Left ArrowNavigates to the left of the items in the display.Right ArrowNavigates to the right of the items in the display.Scan Priority 1Detects activity on channel/group designated as Priority 1.Scan Priority 2Detects activity on channel/group designated as Priority 2.NAG_LACR.book Page 12 Monday, August 23, 2010 1:03 PM

Identifying Status IndicatorsEnglish13LED IndicatorThe LED indicator shows the operational status of your radio. Blinking red – Radio is transmitting at low battery condition, receiving an emergency transmission or has failed the self-test upon powering up.Solid yellow – Radio is in Permanent Monitor mode, at a fair battery condition, monitoring a channel, or requested trunked call has no voice channel or target is busy.Blinking yellow – Radio is scanning for activity or receiving a Call Alert.Solid green – Radio is transmitting or at a good battery condition.Blinking green – Radio is powering up, receiving a call or data, or detecting activity over the air.NOTE: Upon a PTT button press, if the radio is programmed for polite operation, the radio automatically determines whether a transmission is permitted via a Talk Permit or a Talk Denial tone.Audio TonesAlert tones provide you with audible indications of the radio’s status or the radio’s response to data received.Indicator TonesHigh-pitched tone Low-pitched tone LED IndicatorContinuous Tone A monotone sound. Sounds continuously until termination.Periodic Tone Sounds periodically depending on the duration set by the radio. Tone starts, stops, and repeats itself.Repetitive Tone A single tone that repeats itself until it is terminated by the user.Momentary Tone Sounds only once for a short period of time defined by the radio.Positive Indicator ToneNegative Indicator ToneNAG_LACR.book Page 13 Monday, August 23, 2010 1:03 PM

Making and Receiving CallsEnglish14Making and Receiving CallsOnce you understand how your MOTOTRBO Portable is configured, you are ready to use your radio.Use this navigation guide to familiarize yourself with the basic Call features:Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 14Selecting a Radio Channel . . . . . . . . . . . . . . . . . . . . . page 15Receiving and Responding to a Radio Call. . . . . . . . . page 15Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . . . page 17Talkaround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 22Monitoring Features . . . . . . . . . . . . . . . . . . . . . . . . . . page 23Selecting a ZoneA zone is a group of channels. Your radio supports up to 130 zones, with a maximum of 16 channels per zone.Use the following procedure to select a zone.Procedure:Press the programmed Zone button and proceed to step 3.ORFollow the procedure below.1S to access the menu.2Por Q to Zone and press N to select.3The current zone is displayed and indicated by a 9.4Por Q to the required zone and press N to select.5The display shows <Zone> Selected momentarily and returns to the selected zone screen.NOTE: The zones appear in alphabetical order, if named.The Zone main menu option will not appear, if the radio is not configured for zones.NAG_LACR.book Page 14 Monday, August 23, 2010 1:03 PM

Making and Receiving CallsEnglish15Selecting a Radio ChannelProcedure:Once the required zone is displayed (if you have multiple zones in your radio), turn the programmed Channel Selector Knob to select the channel, subscriber alias or ID, or group alias or ID.Receiving and Responding to a Radio CallOnce you have selected the required channel and/or zone, you can proceed to receive and respond to calls.The LED lights up solid green while the radio is transmitting and blinks green when the radio is receiving.Receiving and Responding to a Group CallNOTE: This is a trunking only feature.To receive a call from a group of users, your radio must be configured as part of that group.Procedure:When you receive a Group Call (while on the Home screen):1The LED blinks green.2The first line of the display shows the alias or ID of the caller, and the RSSI icon. The second line displays the related personality alias.3Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.4Press the PTT button to respond to the call. The LED lights up solid green.5Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone.6Release the PTT button to listen.7If there is no voice activity for a predetermined period of time, the call ends.See Making a Group Call on page 18 for details on making a Group Call.LED IndicatorNAG_LACR.book Page 15 Monday, August 23, 2010 1:03 PM

Making and Receiving CallsEnglish16NOTE: If the radio receives a Group Call while not on the Home screen, it remains on its current screen prior to answering the call.Long press the R button to go to the Home screen to view the caller alias before replying.Receiving and Responding to a Private CallNOTE: This is a trunking only feature.A Private Call is a call from an individual radio to another individual radio.There are two types of Private Calls. The first type is called Enhanced Private Call, where a radio presence check is performed prior to setting up the call, while the other, Basic Private Call, sets up the call immediately.Procedure:When you receive a Private Call:1A tone sounds and the LED blinks green.2The first line of the display shows the subscriber alias or ID, and the Private Call and RSSI icons. The second line displays Response.3Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.4Press N to select Response.ORPress the Call button within 20 seconds after the call indicators begin.5The first line of the display shows the subscriber alias or ID, and the Private Call and RSSI icons. The second line displays Private Call.6Press and hold the PTT button to respond.7The first line of the display shows Calling. The second line displays the subscriber alias or ID, and the Private Call icon.8When you are connected, the first line of the display shows the subscriber alias or ID, and the Private Call and RSSI icons. The second line displays Private Call.9 Release the PTT button to listen.See Making a Private Call on page 18 for details on making a Private Call.NAG_LACR.book Page 16 Monday, August 23, 2010 1:03 PM

Making and Receiving CallsEnglish17Receiving and Responding to a Phone CallA Phone Call is a call similar to a standard phone call from a landline phone.Procedure:When you receive a Phone Call:1A tone sounds and the LED blinks green.2The first line of the display shows Phone Call and the RSSI icon. The second line displays Response.3Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.4Press N to select Response.5The first line of the display shows Phone Call. The second line displays Responding.6Press and hold the PTT button to talk. Release the PTT button to listen.See Making a Phone Call on page 20 for details on making a Phone Call.Making a Radio CallYou can select a zone, channel, subscriber ID, or group by using:•The Channel Selector Knob•A programmed One Touch Call button*•The Contacts list from Contacts menu or via Call button (see Contacts Settings on page 29)*•Manual Dial (via Call button) – This method is for Private Calls only and is dialed using the keypad (see Making a Private Call from Contacts on page 29)** A trunking only featureNAG_LACR.book Page 17 Monday, August 23, 2010 1:03 PM

Making and Receiving CallsEnglish18Making a Call with the Channel Selector KnobMaking a Group CallNOTE: This is a trunking only feature.To make a call to a group of users, your radio must be configured as part of that group.Procedure:1Turn the Channel Selector Knob to select the channel with the targeted talkgroup.2Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.3Press the PTT button to make the call. The LED lights up solid green.4Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone.5Release the PTT button to listen.Making a Private CallNOTE: This is a trunking only feature.Procedure:Press the programmed Quick Access (One-Touch) Private Call button to dial the programmed ID (number) and proceed to Step 4.ORFollow the procedure below.1Press the Call button to call.2The display shows the call list, you can scroll through and select the required ID (any target ID or last transmitted or received ID) or go to the manual dial option to enter the required ID.3Press the PTT button to start the Private Call. The LED lights up solid green.4The first line of the display shows Calling. The second line displays the target alias or ID and the Private Call icon.NAG_LACR.book Page 18 Monday, August 23, 2010 1:03 PM

Making and Receiving CallsEnglish195Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.6When you are connected, the first line of the display shows the ID or alias of the target radio and the Private Call icon. The second line displays Private Call. Press and hold the PTT button to talk. Release the PTT button to listen.ORIf no acknowledgment is received, the display shows No Answer.You can also make a Private Call via Contacts (see Making a Private Call from Contacts on page 29) or perform a quick alphanumeric search for the required alias via a keypad entry (see Making a Private Call by Alias Search on page 30).Making an Enhanced Private CallNOTE: This is a trunking only feature.This feature allows you to send an individual Call Alert page if there is no answer from the target radio.NOTE: Your radio must be programmed to allow you to use this feature.Procedure:Press the programmed Quick Access (One-Touch) Private Call button to dial the programmed ID (number) and proceed to Step 4.ORFollow the procedure below.1Press the Call button to Call.2The display shows the call list, you can scroll through and select the required ID (any target ID or last transmitted or received ID) or go to the manual dial option to enter the required ID.3Press the PTT button to initiate the Private Call request.4The first line of the display shows Calling. The second line displays the target alias or ID and the Private Call icon.5When you are connected, the first line of the display shows the ID or alias of the target radio and Private Call icon. The second line displays Private Call. You may hear the Private Call voice if the target is talking.6Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. Press and hold the PTT button to talk. Release the PTT button to listen.ORIf no acknowledgment is received, the display shows No Answer.NAG_LACR.book Page 19 Monday, August 23, 2010 1:03 PM

Making and Receiving CallsEnglish20Making a Phone CallThis feature allows you to make calls similar to standard phone calls to a mobile or landline phone. Your radio must be programmed to allow you to use Delayed Access Buffered Dialing method for below procedure.Procedure:Press the programmed Quick Access (One-Touch) Private Call button to dial the programmed phone number and proceed to Step 4.ORFollow the procedure below.1Press Phone button.2The display shows the phone list, you can scroll through and select the required ID (any target ID or last transmitted or received ID) or go to the manual dial option to enter the required ID.3Press the PTT button to initiate the Phone Call request. The LED lights up solid green.4The first line of the display shows Calling. The second line displays the target alias or ID and the Phone Call icon. The dial tone will be heard, then DTMF tone sounded for phone ID Transmission.5After phone number transmission, the first line of the display shows the phone alias or number and the Phone Call icon, the second line displays Phone Call, and you may hear the voice from the telephone user.6When your call is answered, hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.7Press the PTT button to talk.8Release the PTT button to listen.Sending a Status CallNOTE: This is a trunking only feature.This feature allows you to send data calls to the dispatcher about a predefined status.Each status can have up to a 14-character name. A maximum of eight status conditions is possible.NOTE: The radio automatically exits the feature, if the time-out timer is enabled, when the radio is left idle and the timer expires. You will hear the Menu Inactive Exit Tone upon feature exit.NAG_LACR.book Page 20 Monday, August 23, 2010 1:03 PM

Making and Receiving CallsEnglish21Procedure:Press the programmed Status button and proceed to Step 3.ORFollow the procedure below.1PorQ to Status and press N to select.2The display shows the last acknowledged status call, or the first status in the list.3PorQ to the required status.4Press N to send the status.5When the dispatcher acknowledges, four tones sound and the display shows Ack Received. The radio returns to normal dispatch operation.ORIf no acknowledgment is received, a low-pitched tone sounds and the display shows No Acknowledge.No traffic is heard on trunked channels while Status Calls is selected. If the radio detects no Status Call activity for six seconds, an alert tone sounds until you press Home or the PTT button.Using the Dynamic Regrouping FeatureNOTE: This is a trunking only feature.This feature allows the dispatcher to temporarily reassign selected radios to a single special channel so they can communicate with each other. This feature is typically used during special operations and is enabled by a qualified radio technician.You will not notice whether your radio has this feature enabled until a dynamic regrouping command is sent by the dispatcher.NOTE: If you try to access a zone or channel that has been reserved by the dispatcher as a dynamically regrouped mode for other users, an invalid tone sounds.Procedure:1When your radio is dynamically regrouped, it automatically switches to the dynamically regrouped channel. A “gurgle” tone sounds and the display shows the dynamically regrouped channel name.2Press the PTT button to talk. Release PTT button to listen.When the dispatcher cancels dynamic regrouping, the radio automatically returns to the zone and channel that you were using before the radio was dynamically regrouped.NAG_LACR.book Page 21 Monday, August 23, 2010 1:03 PM

Making and Receiving CallsEnglish22TalkaroundNOTE: This is a conventional only feature.You can continue to communicate when your repeater is not operating, or when your radio is out of the repeater’s range but within talking range of other radios. This is called “talkaround”.Procedure:Press the programmed Repeater/Talkaround button to toggle between talkaround and repeater modes.ORFollow the procedure below.1S to access the menu.2Por Q to Utilities and press N to select.3Por Q to Radio Settings and press N to select.4Por Q to Talkaround and press N to select.5You see Turn On if the radio is currently in Repeater mode. ORYou see Turn Off if the radio is currently in Talkaround mode.6Press N to select.7The display shows Talkaround On.ORThe display shows Talkaround Off.8The screen automatically returns to the previous menu.The Talkaround setting is retained even after powering down.NAG_LACR.book Page 22 Monday, August 23, 2010 1:03 PM

Making and Receiving CallsEnglish23Monitoring FeaturesNOTE: This is a conventional only feature.Monitoring a ChannelUse the Monitor feature to make sure a channel is clear before transmitting.Procedure:1Press and hold the programmed Monitor button and listen for activity. The monitor icon appears on the display.2You hear radio activity or total silence, depending on how your radio is programmed.3When you hear “white noise” (that is, the channel is free), press the PTT button to talk and release it to listen. The LED lights up solid yellow.Permanent MonitorUse the Permanent Monitor feature to continuously monitor a selected channel for activity.Procedure:1Press the programmed Permanent Monitor button.2Radio sounds an alert tone, the LED lights up solid yellow, and the display shows Permanent Monitor On. The Monitor icon appears on the display.3Press the programmed Permanent Monitor button to exit Permanent Monitor mode.4Radio sounds an alert tone, the LED turns off, and display shows Permanent Monitor Off.NAG_LACR.book Page 23 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish24Advanced FeaturesUse this navigation guide to learn more about advanced features available with your radio:Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 24Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 26Contacts Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 29Call Indicator Settings . . . . . . . . . . . . . . . . . . . . . . . . . page 30Call Log Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 31Call Alert Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . page 33Emergency Operation . . . . . . . . . . . . . . . . . . . . . . . . . page 34Dual-Tone Multi Frequency (DTMF) . . . . . . . . . . . . . . page 40Trunking System Controls. . . . . . . . . . . . . . . . . . . . . . page 40Utilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 42Scan ListsScan lists are created and assigned to individual channels/groups. Your radio scans for voice activity by cycling through the channel/group sequence specified in the scan list for the current channel/group.Your radio can support up to 128 scan lists, with a maximum of 16 members in a list. You can add, delete, or prioritize channels by editing a scan list.NOTE: Priority scan is only available in trunking mode.Viewing an Entry in the Scan ListProcedure:1S to access the menu.2Por Q to Scan and press N to select.3Por Q to View/Edit List and press N to select.4Use Por Q to view each member on the list.The priority icon appears left of the member’s alias, if set, to indicate whether the member is on a Priority 1 or Priority 2 channel list. You cannot have multiple Priority 1 or Priority 2 channels in a scan list.There is no priority icon if priority is set to None.NAG_LACR.book Page 24 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish25Editing the Scan ListAdding a New Entry to the Scan ListProcedure:1S to access the menu.2Por Q to Scan and press N to select.3Por Q to View/Edit List and press N to select.4Por Q to Add Member and press N to select.5Por Q to the required alias or ID and press N to select.6Por Q to the required priority level and press N to select.7The display shows Entry Saved, followed immediately by Add Another?.8Por Q to Yes and press N to select, to add another entry, and repeat steps 5 and 6.ORPor Q to No and press N to select to save the current list.Deleting an Entry from the Scan ListProcedure:1S to access the menu.2Por Q to Scan and press N to select.3Por Q to View/Edit List and press N to select.4Por Q to the required alias or ID and press N to select.5Por Q to Delete and press N to select.6At Delete Entry?, Por Q to Yes and press N to select, to delete the entry. The display shows Entry Deleted. ORPor Q to No and press N to select to return to the previous screen.7Repeat steps 4 to 6 to delete other entries.After deleting all required aliases or IDs, long press R to return to the Home screen.NAG_LACR.book Page 25 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish26Setting and Editing Priority for an Entry in the Scan ListProcedure:1S to access the menu.2Por Q to Scan and press N to select.3Por Q to View/Edit List and press N to select.4Por Q to the required alias or ID and press N to select.5Por Q to Edit Priority and press N to select.6Por Q to the required priority level and press N to select.7The display shows Entry Saved before returning to the previous screen.8The priority icon appears left of the member’s name.There is no priority icon if priority is set to None.ScanWhen you start a scan, your radio cycles through the programmed scan list for the current channel looking for voice activity.The LED blinks yellow and you see the scan icon on the display.There are two ways of initiating scan:•Main Channel Scan (Manual): Your radio scans all the channels/groups in your scan list. On entering scan, your radio may – depending on the settings – automatically start on the last scanned “active” channel/group or on the channel where scan was initiated.•Auto Scan (Automatic): Your radio automatically starts scanning when you select a channel/group that has Auto Scan enabled.NAG_LACR.book Page 26 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish27Starting and Stopping ScanProcedure:Press the programmed Scan button to start or stop Scan.ORFollow the procedure below.1Use the Channel Selector Knob to select a channel programmed with a scan list.2S to access the menu.3Por Q to Scan and press N to select.4The display shows Turn On if scan is disabled.ORThe display shows Turn Off if scan is enabled.5Press N to select.6The LED blinks yellow and the scan icon is displayed when Scan is enabled.ORThe LED turns off and the scan icon is not displayed when Scan is disabled.Responding to a Transmission During a ScanDuring scanning, your radio stops on a channel/group where activity is detected. The radio stays on that channel for a programmed time period known as “hang time”.Procedure:1Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.2Press the PTT button during hang time. The LED lights up solid green.3Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone.4Release the PTT button to listen.5If you do not respond within the hang time, the radio returns to scanning other channels/groups.NAG_LACR.book Page 27 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish28Deleting a Nuisance ChannelIf a channel continually generates unwanted calls or noise (termed a “nuisance” channel), you can temporarily remove the unwanted channel from the scan list.This capability does not apply to the channel designated as the Selected Channel.Procedure:1When your radio “locks on to” an unwanted or nuisance channel, press the programmed Nuisance Delete button until you hear a tone.2Release the Nuisance Delete button. The nuisance channel is deleted.Deleting a “nuisance” channel is only possible through the programmed Nuisance Delete button. This feature is not accessible through the menu.Restoring a Nuisance ChannelProcedure:To restore the deleted nuisance channel, do ONE of the following:•Turn the radio off and then powering it on again, OR•Stop and restart a scan via the programmed Scan button or menu, OR•Change the channel via the Channel Selector Knob.NAG_LACR.book Page 28 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish29Contacts SettingsContacts provides “address-book” capabilities on your radio. Each entry corresponds to an alias or ID that you use to initiate a call.Additionally, each entry, depending on context, associates with ONE of four types of calls: Phone Call, Private Call, Selective Call or Call Alert.PC Call and Dispatch Call are data-related. They are only available with the applications. Refer to the data applications documentation for more information.Your radio supports one Contacts list, with a maximum of 250 members for Radio Call entry and a maximum of 50 members for Phone Call entry.Each entry within Contacts displays the following information:•Call Type•Call Alias•Call IDNOTE: You can add, delete, or edit subscriber IDs for the Contacts list.Making a Private Call from ContactsProcedure:1S to access the menu.2Por Q to Contacts and press N to select.The entries are alphabetically sorted.3Por Q to the required subscriber alias or ID.4Press the PTT button to start the Private Call. The first line displays Calling. The second line displays the target alias or ID and the Private Call icon.5When you are connected, the display shows the ID or alias of the target radio and the Private Call icon. Private Call is displayed on second line. Talk Permit Tone will be heard if enabled.6Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.7Press and hold the PTT button to talk. Release the PTT button to listen.NAG_LACR.book Page 29 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish30Making a Private Call by Alias SearchYou can also use alias or alphanumeric search to retrieve the required subscriber alias.This feature is only applicable while in Contacts.Procedure:1S to access the menu.2Por Q to Contacts and press N to select. The entries are alphabetically sorted.3Key in the first character of the alias.4Por Q to the required alias.5Press the PTT button to start the Private Call. The first line displays Calling. The second line displays the target alias or ID and the Private Call Icon.6When you are connected, the display shows the ID or alias of the target radio and the Private Call icon. Private Call is displayed on the second line. Talk Permit Tone will be heard if enabled.7Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.8Press and hold the PTT button to talk. Release the PTT button to listen.Call Indicator SettingsActivating and Deactivating Call Ringers for Private CallsNOTE: This is a trunking only feature.You can turn on or off the ringing tones for a received Private Call.Procedure:1S to access the menu.2Por Q to Utilities and press N to select.3Por Q to Radio Settings and press N to select.4Por Q to Tones/Alerts and press N to select.5Por Q to Call Ringers and press N to select.6Por Q to Private Call and press N to select.7The display shows Turn On. Press N to enable Call Ringers for Private Calls. The display shows Private Call Ringer On. ORThe display shows Turn Off. Press N to disable Call Ringers for Private Calls. The display shows Private Call Ringer Off.NAG_LACR.book Page 30 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish31NOTE: To activate or deactivate call ringer for Selective Call/Call Alert/Phone Call, follow similar steps as above.Escalating Alarm Tone VolumeYour radio can be programmed to continually alert you when a radio call remains unanswered. This is done by automatically increasing the alarm tone volume over time. This feature is known as Escalert.Procedure:1S to access the menu.2Por Q to Utilities and press N to select.3Por Q to Radio Settings and press N to select.4Por Q to Tones/Alerts and press N to select.5Por Q to Escalert and press N to select.6The display shows Turn On. Press N to enable Escalert. The display shows Escalert On.ORThe display shows Turn Off. Press N to disable Escalert. The display shows Escalert Off.Call Log FeaturesYour radio keeps track of all recent incoming and outgoing Radio Calls, and outgoing Phone Calls. Use the call log feature to view and manage recent calls.NOTE: Incoming and outgoing Radio Calls are trunking only features.You can perform the following tasks in each of your call lists:•Store ID to Contacts•DeleteViewing Recent CallsThe lists are Radio Rcvd, Radio Dialed, and Phone Dialed.Procedure:1S to access the menu.2Por Q to Call Log and press N to select.3Por Q to preferred list and press N to select.4The display shows the most recent entry at the top of the list.5Por Q to view the list.NAG_LACR.book Page 31 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish32Storing an Alias or ID from the Received Call ListProcedure:1S to access the menu.2Por Q to Call Log and press N to select.3Por Q to Radio Rcvd and press N to select.4Por Q to the required received call alias or ID and press N to select.5Por Q to Store and press N to select.6A blinking cursor appears. If needed, key in the alias for that ID and press N.7The display shows Contact Saved.You can also store an ID without an alias.Deleting a Call from a Call ListProcedure:1S to access the menu.2Por Q to Call Log and press N to select.3Por Q to the required list and press N to select.4Por Q to the required alias or ID and press N to select.5Por Q to Delete Entry? and press N to select.6Press N to select Yes to delete the entry. The display shows Entry Deleted.ORPor Q to No to return to the previous screen.When you select a call list and it contains no entries, the display shows List Empty, and sounds a low tone if Keypad Tones are turned on (see Turning Keypad Tones On or Off on page 43).NAG_LACR.book Page 32 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish33Call Alert OperationNOTE: This is a trunking only feature.Call Alert paging enables you to alert a specific radio user to call you back when they are able to do so.This feature is applicable for subscriber aliases or IDs only and is accessible through the menu via Contacts or manual dial.Receiving and Acknowledging a Call AlertWhen you receive a Call Alert page, you see Call Alert that alternates with the alias or ID of the calling radio on the display.Procedure:1You hear a repetitive tone. The LED blinks yellow.2Press and release the PTT button to acknowledge the alert.ORPress N to select Ignore? and to exit the Call Alert.Making a Call Alert from the Contacts ListProcedure:1S to access the menu.2Por Q to Contacts and press N to select.3Por Q to the required subscriber alias or ID and press N to select.4Por Q to Call Alert and press N to select.5The display shows Call Alert: <Subscriber Alias or ID>, indicating that the Call Alert has been sent. 6The LED lights up solid green when your radio is sending the Call Alert.7If the Call Alert acknowledgment is received, a tone sounds and the display shows Call Alert Successful.ORIf the Call Alert acknowledgment is not received, a tone sounds and the display shows Call Alert Failed.NAG_LACR.book Page 33 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish34Making a Call Alert with the One Touch Call ButtonProcedure:1Press the programmed One Touch Call button to make a Call Alert to the predefined alias or ID.2The display shows Call Alert: <Subscriber Alias or ID>, indicating that the Call Alert has been sent. 3The LED lights up solid green when your radio is sending the Call Alert.4If the Call Alert acknowledgment is received, a tone sounds and the display shows Call Alert Successful.ORIf the Call Alert acknowledgment is not received, a tone sounds and the display shows Call Alert Failed.Emergency OperationNOTE: This is a trunking only feature.The Emergency feature is used to indicate a critical situation. You are able to initiate an Emergency at any time on any screen display even when there is activity on the current channel.Your radio supports the following Emergency modes:•Emergency Call•Emergency Alarm•Emergency Alarm with Call•Emergency Alarm with Voice to FollowIn addition, each mode has the following types:•Regular – Radio transmits an alarm signal and shows audio and/or visual indicators.•Silent – Radio transmits an alarm signal without any audio or visual indicators. There will be no response (call) from the target radio until you press the PTT button to initiate the call.•Silent with Voice – Radio transmits an alarm signal and is able to receive an incoming call, without any audio or visual indicators, until you press the PTT button to initiate, or respond to, the call.Only ONE of the Emergency modes above can be assigned to the programmed Emergency button.NAG_LACR.book Page 34 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish35Receiving an Emergency CallProcedure:1When receiving an Emergency Call, the first line of the display shows the alias or ID of the caller. The second line displays Emergency.2The LED blinks red and you hear a voice from the Emergency Call initiating radio.3If the voice channel is lost, the Emergency Call ends.Receiving an Emergency AlarmProcedure:1When receiving an Emergency Alarm, the first line of the display shows the alias or ID of the sender. The second line displays Alarm Rcvd.2A tone sounds and the LED blinks red.3Press R to clear the alarm indication.ORIf no button is pressed, the alarm indication exits automatically after a short duration.When your radio receives an Emergency Alarm, it displays the Emergency Alarm received indications for approximately, 10 seconds.Receiving an Emergency Alarm with CallProcedure:1When receiving an Emergency Alarm with Call, the first line of the display shows the alias or ID of the sender. The second line displays Alarm Rcvd.2A tone sounds and the LED blinks red.3Press R to clear the alarm indication.ORIf no button is pressed, the alarm indication exits automatically after a short duration.4You hear a voice from the Emergency Alarm with Call initiating radio.5Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.6Press PTT button to initiate a call with the emergency initiating radio. The LED lights up solid green.7Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone.8Release the PTT button to listen. When the emergency initiating radio responds, the LED blinks green.NAG_LACR.book Page 35 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish36Sending an Emergency CallThis feature gives your radio priority access on a channel.NOTE: The radio operates in the normal dispatch manner while in Emergency Call, except, if enabled, it returns to one of the following:•Tactical/Non-Revert – You talk on the channel you selected before you entered the emergency state.•Non-Tactical/Revert – You talk on a programmed emergency channel. The emergency alarm is sent on this same channel.Procedure: 1Press the programmed Emergency button.2The display shows Emergency on the second line. The LED lights up solid green and the Emergency icon appears on the Home screen display.ORThe radio sounds a low-pitched tone, if the selected channel does not support emergency. Select a channel that shows Emergency.3Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.4Press and hold the PTT button. Speak clearly into the microphone.5Release the PTT button to end the transmission and wait for a response from the dispatcher.6Press and hold the programmed Emergency button for about a second to exit the Emergency Call mode.If your radio is set to Silent, it will not have any audio or visual indicators related to the Emergency feature.Sending an Emergency AlarmThis feature allows you to send an Emergency Alarm, a non-voice signal, which triggers an alert indication on another radio. Procedure: 1Press the programmed Emergency button.2The display shows Sending Alarm on the second line. The LED lights up solid green and the Emergency icon appears on the Home screen display. An Emergency Enter Tone sounds upon each retry.NAG_LACR.book Page 36 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish373When an Emergency Alarm acknowledgment is received, the Emergency Acknowledgment Tone sounds and the LED blinks green. The display shows Emergency Alarm Successful.ORIf your radio does not receive an Emergency Alarm acknowledgment, and after all retries have been exhausted, a tone sounds and the display shows Emergency Alarm Failed. 4Radio exits the Emergency Alarm mode and returns to the Home screen.If your radio is set to Silent, it will not have any audio or visual indicators related to the Emergency feature.Sending an Emergency Alarm with CallThis feature allows you to send an Emergency Alarm to another radio. Upon acknowledgment, both radios can communicate over a programmed Emergency channel.Procedure: 1Press the programmed Emergency button.2The display shows Sending Alarm on the second line. The LED lights up solid green and the Emergency icon appears on the Home screen display. An Emergency Enter Tone sounds upon each retry.3When an Emergency Alarm acknowledgment is received, the Emergency Acknowledgment Tone sounds and the LED blinks green. The display shows Emergency Alarm Successful.4Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.5Press PTT button to make the call. The display shows Emergency on the second line. The LED lights up solid green and the Emergency icon appears on the Home screen display. 6Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone.7Release the PTT button to listen.8Long press the programmed Emergency button to exit the Emergency mode.9The radio returns to the Home screen.NAG_LACR.book Page 37 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish38If your radio is set to Silent, it will not have any audio or visual indicators related to the Emergency feature, or receive any response (call) from the target radio, until you press the PTT button to initiate the call.If your radio is set to Silent with Voice, it will not have any audio or visual indicators related to the Emergency feature, or when you are receiving a call from the target radio. The indicators will only appear once you press the PTT button to initiate, or respond to, the call.Sending an Emergency Alarm with Voice to FollowThis feature allows you to send an Emergency Alarm to another radio. Upon acknowledgment, your radio’s microphone is automatically activated, allowing you to communicate with the other radio without pressing the PTT button.This activated microphone state is also known as “hot mic”.If you press the PTT button during the programmed hot mic transmission period, the radio ignores the PTT press and remains in Emergency mode.NOTE: If you press the PTT button during hot mic, and continue to press it after the hot mic duration expires, the radio continues to transmit until you release the PTT button.Procedure: 1Press the programmed Emergency button.2The display shows Sending Alarm. The LED lights up solid green and the Emergency icon is displayed.3Once the display shows Emergency Alarm Successful, speak clearly into the microphone. When hot mic has been enabled, the radio automatically transmits without a PTT press until the hot mic duration expires.4While transmitting, the LED lights up solid green and the Emergency icon appears on the display.5Once the hot mic duration expires, the radio automatically stops transmitting. To transmit again, press the PTT button.NAG_LACR.book Page 38 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish39If your radio is set to Silent, it will not have any audio or visual indicators related to the Emergency feature, or receive any response from the target radio, until the programmed hot mic transmission period is over, and you press the PTT button.If your radio is set to Silent with Voice, it will not have any audio or visual indicators related to the Emergency feature when you are making the call with hot mic, or when the target radio responds after the programmed hot mic transmission period is over. The indicators will only appear when you press the PTT button.NOTE: If the Emergency Alarm request fails, the radio returns to the Home screen.Reinitiating an Emergency ModeThere are two instances where this can happen:•You change the channel while the radio is in Emergency mode. This exits the Emergency mode. If Emergency Alarm is enabled on this new channel, the radio reinitiates Emergency. If Emergency is not supported on this new channel, the radio displays No Emergency.•You press the programmed Emergency button during an Emergency initiation/transmission state. This causes the radio to exit this state, and to reinitiate Emergency.Exiting Emergency ModeYour radio exits Emergency mode when ONE of the following occurs:•Emergency Alarm acknowledgment is received(for Emergency Alarm only), OR•All retries to send the alarm have been exhausted(for Emergency Alarm only), OR•The programmed Emergency button is long pressed.NOTE: If your radio is powered off, it exits the Emergency mode. The radio will not reinitiate the Emergency mode automatically when it is turned on again.NAG_LACR.book Page 39 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish40Dual-Tone Multi Frequency (DTMF)The Dual-Tone Multi Frequency (DTMF) feature allows the radio to operate in a radio system with an interface to telephone systems.Procedure:To initiate a DTMF call.1Press and hold the PTT button.2Enter the desired number.You can turn off the DTMF tone by disabling all radio tones and alerts (see Turning the Radio Tones/Alerts On or Off on page 45).Trunking System ControlsNOTE: This is a trunking only feature.Using the Failsoft SystemThe failsoft system ensures continuous radio communications during a trunked system failure. If a trunking system fails completely, the radio goes into failsoft operation and automatically switches to its failsoft channel.Procedure: 1During failsoft operation, your radio transmits and receives in conventional operation on a predetermined frequency.2A medium-pitched tone sounds every 10 seconds and the display shows Failsoft, which alternates with the personality alias.When the trunking system returns to normal operation, your radio automatically leaves failsoft operation and returns to trunked operation.Going Out of RangeWhen your radio goes out of the range of the system, it can no longer lock onto a control channel.Procedure:1A low-pitched tone sounds.AND/ORThe display shows the currently selected channel combination and Out of Range.2Your radio remains in this out-of-range condition until:It locks onto a control channel.ORIt locks onto a failsoft channel.ORIt is turned off.NAG_LACR.book Page 40 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish41Using the Site Trunking FeatureIf the zone controller loses communication with any site, that site reverts to site trunking.The display shows the currently selected channel combination and Site Trunking.NOTE: When this occurs, you can communicate only with other radios within your trunking site.Locking and Unlocking a SiteThis feature allows your radio to lock onto a specific site and not roam among wide-area talkgroup sites. This feature should be used with caution, since it inhibits roaming to another site in a wide-area system.Procedure:Use the preprogrammed Site Lock/Unlock button to toggle the lock state between locked and unlocked.ORFollow the procedure below.1S to access the menu.2Por Q to Utilities and press N to select.3Por Q to Radio Settings and press N to select.4Por Q to Site Lock and press N to select.5You see Turn On if the site is currently in unlocked state. ORYou see Turn Off if the site is currently in locked state.6Press N to select.7The display shows Site Locked.ORThe display shows Site Unlocked.8The radio saves the new site lock state and returns to the Home screen.Viewing and Changing a SiteThis feature allows you to view the number of the current site or force your radio to change to a new one.Viewing and Changing a SiteProcedure: 1Press the preprogrammed Site Display button (it could be short press or long press based on the configuration of the programmable button).2The display momentarily shows the name of the current site and its corresponding received signal strength indicator (RSSI).NAG_LACR.book Page 41 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish42Changing the Current SiteProcedure:1Press the preprogrammed Site Search button (it could be short press or long press based on the configuration of the programmable button).2A tone sounds and the display momentarily shows Scanning site.3When the radio finds a new site, it returns to the Home screen.UtilitiesLocking and Unlocking the KeypadYou can lock your radio’s keypad to avoid inadvertent key entry.Procedure:1S to access the menu.2Por Q to Utilities and press N to select.3Por Q to Radio Settings and press N to select.4Por Q to Keypad Lock and press N to select.5The display shows Keypad Locked and returns to the Home screen.6To unlock the keypad, press S followed by *.7The display shows Keypad Unlocked and returns to the Home screen.NAG_LACR.book Page 42 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish43Turning Keypad Tones On or OffYou can enable and disable keypad tones if needed.Procedure:1S to access the menu.2Por Q to Utilities and press N to select.3Por Q to Radio Settings and press N to select.4Por Q to Tones/Alerts and press N to select.5Por Q to Keypad Tones and press N to select.6The display shows Turn On. Press N to enable keypad tones. The display shows Keypad Tone On.ORThe display shows Turn Off. Press N to disable keypad tones. The display shows Keypad Tone Off. Setting the Squelch LevelNOTE: This is a conventional only feature.You can adjust your radio's squelch level to filter out unwanted calls with low signal strength or channels that have a higher than normal background noise.Settings: Normal is the default. Tight filters out (unwanted) calls and/or background noise. However, calls from remote locations may also be filtered out.Procedure:Press the programmed Squelch button to toggle squelch level between normal and tight.ORFollow the procedure below.1S to access the menu.2Por Q to Utilities and press N to select.3Por Q to Radio Settings and press N to select.4Por Q to Squelch and press N to select.5Choose either Tight or Normal and press N to select.6Screen returns to the previous menu.NAG_LACR.book Page 43 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish44Setting the Power LevelYou can customize your radio’s power setting to high or low for each channel.Settings: High enables communication with radios located at a considerable distance from you. Low enables communication with radios in closer proximity.Procedure:Press the programmed Power Level button to toggle transmit power level between high and low. ORFollow the procedure below.1S to access the menu.2Por Q to Utilities and press N to select.3Por Q to Radio Settings and press N to select.4Por Q to Power and press N to select.5Change your current setting as prompted on the display.6Press N to select a new power level.7Screen returns to the previous menu.Long press R to return to the Home screen. The power level icon is visible.Controlling the Display BacklightYou can enable or disable the radio’s display backlight as needed. The setting also affects the Menu Navigation Buttons and keypad backlighting accordingly.Procedure:Press the programmed Backlight button to toggle the backlight settings.ORFollow the procedure below.1S to access the menu.2Por Q to Utilities and press N to select.3Por Q to Radio Settings and press N to select.4Por Q to Backlight and press N to select.5The display shows Auto On. Press N to enable the display backlight. The display shows Backlight Auto On.ORThe display shows Turn Off. Press N to disable the display backlight. The display shows Backlight Turn Off.The display backlight and keypad backlighting are automatically turned off if the LED indicator is disabled (see Turning the LED Indicator On or Off on page 46).NAG_LACR.book Page 44 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish45Turning the Radio Tones/Alerts On or OffYou can enable and disable all radio tones and alerts (except for the incoming Emergency alert tone) if needed.Procedure:Press the programmed All Tones/Alerts button to toggle all tones on or off.ORFollow the procedure below.1S to access the menu.2Por Q to Utilities and press N to select.3Por Q to Radio Settings and press N to select.4Por Q to Tones/Alerts and press N to select.5Por Q to All Tones and press N to select.6The display shows Turn On. Press N to enable all tones and alerts. The display shows All Tones On.ORThe display shows Turn Off. Press N to disable all tones and alerts. The display shows All Tones Off.Turning the Talk Permit Tone On or OffYou can enable and disable the Talk Permit Tone if needed.Procedure:1S to access the menu.2Por Q to Utilities and press N to select.3Por Q to Radio Settings and press N to select.4Por Q to Tones/Alerts and press N to select.5Por Q to Talk Permit and press N to select.6The display shows Turn On. Press N to enable the Talk Permit Tone. The display shows Talk Permit Tone On.ORThe display shows Turn Off. Press N to disable the Talk Permit Tone. The display shows Talk Permit Tone Off.NAG_LACR.book Page 45 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish46Turning the LED Indicator On or OffYou can enable and disable the LED Indicator if needed.Procedure:1S to access the menu.2Por Q to Utilities and press N to select.3Por Q to Radio Settings and press N to select.4Por Q to LED Indicator and press N to select.5The display shows Turn On. Press N to enable the LED Indicator. The display shows All LEDs On.ORThe display shows Turn Off. Press N to disable the LED Indicator. The display shows All LEDs Off.The display backlight, buttons, and keypad backlighting are automatically turned off if the LED indicator is disabled (see Controlling the Display Backlight on page 44).Turning the Introduction Screen On or OffYou can enable and disable the Introduction Screen if needed.Procedure:1S to access the menu.2Por Q to Utilities and press N to select.3Por Q to Radio Settings and press N to select.4Por Q to Intro Screen and press N to select.5The display shows Turn On. Press N to enable the Introduction Screen. The display shows Intro Screen On.ORThe display shows Turn Off. Press N to disable the Introduction Screen. The display shows Intro Screen Off.NAG_LACR.book Page 46 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish47Accessing General Radio InformationYour radio contains information on the following:•Battery•Radio ID•Software Version•Codeplug VersionNOTE: Press R at any time to return to the previous screen or long press R to return to the Home screen.Accessing the Battery InformationDisplays information on your radio battery.Procedure:1S to access the menu.2Por Q to Utilities and press N to select.3Por Q to Radio Info and press N to select.4Por Q to Battery Info and press N to select. 5The display shows the battery information.ORFor IMPRES batteries ONLY: The display reads Recondition Battery if the battery requires reconditioning in an IMPRES charger. After the reconditioning process, the display then shows the battery information.For IMPRES batteries ONLY:Press Por Q to access the Remaining Capacity, First Used, or Service Life option screen:•Select Remaining Capacity to view battery capacity level, indicated by a horizontal bar and percentage reading.•Select First Used to view the date when battery is first used.•Select Service Life to view the potential and current capacity of the battery.NAG_LACR.book Page 47 Monday, August 23, 2010 1:03 PM

Advanced FeaturesEnglish48Checking the Radio IDNOTE: This is a trunking only feature.Displays the ID of your radio. Procedure: 1S to access the menu.2Por Q to Utilities and press N to select.3Por Q to Radio Info and press N to select.4Por Q to My Number and press N to select.5The display shows the radio ID.Checking the Firmware VersionDisplays the firmware version on your radio.Procedure: 1S to access the menu.2Por Q to Utilities and press N to select.3Por Q to Radio Info and press N to select.4Por Q to Firmware Ver. and press N to select.5The display shows the current firmware version.Checking the Codeplug VersionDisplays the codeplug version on your radio.Procedure: 1S to access the menu.2Por Q to Utilities and press N to select.3Por Q to Radio Info and press N to select.4Por Q to CP Ver. and press N to select.5The display shows the current codeplug version.NAG_LACR.book Page 48 Monday, August 23, 2010 1:03 PM

AccessoriesEnglish49AccessoriesYour radio is compatible with the accessories listed in this chapter. Contact your dealer or system administrator for details.Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 49Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 49Carry Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 50Chargers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 50Remote Speaker Microphones . . . . . . . . . . . . . . . . . . page 50Miscellaneous Accessories . . . . . . . . . . . . . . . . . . . . . page 50AntennasThe diagram on the right shows the location of the color indicator for the following antennas. See the footnote at the end of the list for the color.•CSA GPS Helical Antenna1, 806 – 941 MHz (PMAF4005_)Color Code:Batteries•MOTOTRBO CSA/IECEx/ATEX IMPRES Li-Ion, 1750 mAh (NNTN7789_)1PurpleNAG_LACR.book Page 49 Monday, August 23, 2010 1:03 PM

AccessoriesEnglish50Carry Devices•Hard Leather Carry Case with 3-Inch Swivel Belt Loop for Display Radio (PMLN5606_)•Soft Leather Carry Case with 3-Inch Swivel Belt Loop for Display Radio (PMLN5607_)•2.5-Inch Swivel Belt Loop (For Use with PMLN5606_ and PMLN5607_) (PMLN5610_)•3-Inch Replacement Swivel Belt Loop (PMLN5611_)•ATEX CSA Belt Clip for 2.5-Inch Belt Width (PMLN5134_)Chargers•IMPRES Multi-Unit Charger (WPLN4211_)•IMPRES Multi-Unit Charger with Display (WPLN4218_)•IMPRES Single-Unit Charger (WPLN4226_)Remote Speaker Microphones•IMPRES ATEX CSA Remote Speaker Microphone (PMMN4067_)Miscellaneous Accessories•Universal Connector Dust Cover for MOTOTRBO ATEX CSA (PMLN5649_)NAG_LACR.book Page 50 Monday, August 23, 2010 1:03 PM

Batteries and Chargers WarrantyEnglish51Batteries and Chargers WarrantyThe Workmanship Warranty The workmanship warranty guarantees against defects in workmanship under normal use and service.The Capacity WarrantyThe capacity warranty guarantees 80% of the rated capacity for the warranty duration.All MOTOTRBO Batteries Two (2) YearsIMPRES Chargers (Single-Unit and Multi-Unit, Non-Display) Two (2) YearsIMPRES Chargers (Multi-Unit with Display) One (1) YearMOTOTRBO CSA/IECEx/ATEX Lithium-Ion IMPRES Batteries 18 MonthsNAG_LACR.book Page 51 Monday, August 23, 2010 1:03 PM

Limited WarrantyEnglish52Limited WarrantyMOTOROLA COMMUNICATION PRODUCTSI. WHAT THIS WARRANTY COVERS AND FOR HOW LONG:MOTOROLA INC. (“MOTOROLA”) warrants the MOTOROLA manufactured Communication Products listed below (“Product”) against defects in material and workmanship under normal use and service for a period of time from the date of purchase as scheduled below:MOTOROLA, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it (with a new or reconditioned Product), or refund the purchase price of the Product during the warranty period provided it is returned in accordance with the terms of this warranty. Replaced parts or boards are warranted for the balance of the original applicable warranty period. All replaced parts of Product shall become the property of MOTOROLA.This express limited warranty is extended by MOTOROLA to the original end user purchaser only and is not assignable or transferable to any other party. This is the complete warranty for the Product manufactured by MOTOROLA. MOTOROLA assumes no obligations or liability for additions or modifications to this warranty unless made in writing and signed by an officer of MOTOROLA. Unless made in a separate agreement between MOTOROLA and the original end user purchaser, MOTOROLA does not warrant the installation, maintenance or service of the Product.MOTOROLA cannot be responsible in any way for any ancillary equipment not furnished by MOTOROLA which is attached to or used in connection with the Product, or for operation of the Product with any ancillary equipment, and all such equipment is expressly excluded from this warranty. Because each system which may use the Product is unique, MOTOROLA disclaims liability for range, coverage, or operation of the system as a whole under this warranty.II. GENERAL PROVISIONS:This warranty sets forth the full extent of MOTOROLA'S responsibilities regarding the Product. Repair, replacement or refund of the purchase price, at MOTOROLA’s option, is the exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. IN NO EVENT SHALL MOTOROLA BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR XPR IS Series Portable Radios Two (2) YearsProduct Accessories (Excluding Batteries and Chargers) One (1) YearNAG_LACR.book Page 52 Monday, August 23, 2010 1:03 PM

Limited WarrantyEnglish53INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW.III. STATE LAW RIGHTS:SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY. This warranty gives specific legal rights, and there may be other rights which may vary from state to state.IV. HOW TO GET WARRANTY SERVICE:You must provide proof of purchase (bearing the date of purchase and Product item serial number) in order to receive warranty service and, also, deliver or send the Product item, transportation and insurance prepaid, to an authorized warranty service location. Warranty service will be provided by MOTOROLA through one of its authorized warranty service locations. If you first contact the company which sold you the Product (e.g., dealer or communication service provider), it can facilitate your obtaining warranty service. You can also call MOTOROLA at 1-800-927-2744 US/Canada.V. WHAT THIS WARRANTY DOES NOT COVER:A) Defects or damage resulting from use of the Product in other than its normal and customary manner.B) Defects or damage from misuse, accident, water, or neglect.C)Defects or damage from improper testing, operation, maintenance, installation, alteration, modification, or adjustment.D)Breakage or damage to antennas unless caused directly by defects in material workmanship.E) A Product subjected to unauthorized Product modifications, disassembles or repairs (including, without limitation, the addition to the Product of non-MOTOROLA supplied equipment) which adversely affect performance of the Product or interfere with MOTOROLA's normal warranty inspection and testing of the Product to verify any warranty claim.F) Product which has had the serial number removed or made illegible.G)Rechargeable batteries if:(1) any of the seals on the battery enclosure of cells are broken or show evidence of tampering.(2) the damage or defect is caused by charging or using the battery in equipment or service other than the Product for which it is specified.H)Freight costs to the repair depot.I) A Product which, due to illegal or unauthorized alteration of the software/firmware in the Product, does not function in accordance with MOTOROLA’s published specifications or the FCC certification labeling in effect for the Product at the time the Product was initially distributed from MOTOROLA.J) Scratches or other cosmetic damage to Product surfaces that does not affect the operation of the Product.K) Normal and customary wear and tear.NAG_LACR.book Page 53 Monday, August 23, 2010 1:03 PM

Limited WarrantyEnglish54VI. PATENT AND SOFTWARE PROVISIONS:MOTOROLA will defend, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a United States patent, and MOTOROLA will pay those costs and damages finally awarded against the end user purchaser in any such suit which are attributable to any such claim, but such defense and payments are conditioned on the following:A) that MOTOROLA will be notified promptly in writing by such purchaser of any notice of such claim;B) that MOTOROLA will have sole control of the defense of such suit and all negotiations for its settlement or compromise; andC)should the Product or parts become, or in MOTOROLA’s opinion be likely to become, the subject of a claim of infringement of a United States patent, that such purchaser will permit MOTOROLA, at its option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non-infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by MOTOROLA.MOTOROLA will have no liability with respect to any claim of patent infringement which is based upon the combination of the Product or parts furnished hereunder with software, apparatus or devices not furnished by MOTOROLA, nor will MOTOROLA have any liability for the use of ancillary equipment or software not furnished by MOTOROLA which is attached to or used in connection with the Product. The foregoing states the entire liability of MOTOROLA with respect to infringement of patents by the Product or any parts thereof.Laws in the United States and other countries preserve for MOTOROLA certain exclusive rights for copyrighted MOTOROLA software such as the exclusive rights to reproduce in copies and distribute copies of such MOTOROLA software. MOTOROLA software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modified in any way, or used to produce any derivative thereof. No other use including, without limitation, alteration, modification, reproduction, distribution, or reverse engineering of such MOTOROLA software or exercise of rights in such MOTOROLA software is permitted. No license is granted by implication, estoppel or otherwise under MOTOROLA patent rights or copyrights.VII. GOVERNING LAW:This Warranty is governed by the laws of the State of Illinois, U.S.A.NAG_LACR.book Page 54 Monday, August 23, 2010 1:03 PM

Navigation menu