Motorola Drc450 Users Manual Moto DRC450_Mnl
DRC450 to the manual a0d07b93-c668-4378-9fcd-586947885c35
2015-01-23
: Motorola Motorola-Drc450-Users-Manual-272357 motorola-drc450-users-manual-272357 motorola pdf
Open the PDF directly: View PDF .
Page Count: 2
Download | |
Open PDF In Browser | View PDF |
Press AUDIO, VCR/DVD, CABLE, or TV once to control a device. DRC450 UNIVERSAL REMOTE CONTROL Press MUTE once to turn sound off or on. In the VCR/DVD and TV modes, use the STOP, PAUSE, PLAY, REW., and F.FWD. keys to control a VCR (or DVD player). To record a program on a VCR, press RECORD once. Use PAGE ▲ (or PAGE ▼) to page up (or down) through menu screens and the electronic program guide. Use LOCK** to restrict viewing of selected programs (Parental Control). Use INFO to display current channel and program information. **NOTE: Functionality of the LOCK and OK keys are dependent on the software and the model of Motorola interactive digital terminal. Use these keys to move the cursor in the electronic program guide and menu screens. INSTALLING BATTERIES 1. 2. 3. OVERVIEW The Motorola DRC450 universal remote will control up to four devices, including Motorola's interactive digital terminals*, most TVs,VCRs,Amplifiers, DVD players, PVRs, Tuners, and CD players. 4. Use GUIDE to display the electronic program guide. *NOTE: Digital models include the DCT1000, DCT1200, DCT1700, DCT2000, DCT2500, and DCT5100. The DRC450 can also control older Motorola analog models like the CT1900, CFT2100, CFT2200, and CFT3300. In TV or CABLE mode, use VOLUME + (or VOLUME -) to raise (or lower) sound volume. The DRC450 requires two new AA alkaline batteries (included) and has easy programming to control your Motorola interactive digital terminal, as well as all of the basic functions of your other original remote controls. Moreover, the DRC450 helps eliminate the need to use multiple remote controls. Use CHANNEL + (or CHANNEL -) to select the next higher (or lower) channel. For best results, please read and perform all instructions listed herein.Also, keep these instructions for future reference. In the CABLE mode, press FAVORITE once to display programmed favorite cable channels. FEATURES AND FUNCTIONS These functions are set by your cable system operator. 5. Use LAST to recall last channel or go back one screen in the menu. Use the DRC450 mode keys (i.e., AUDIO, VCR/DVD, CABLE, or TV) to control a specific device.When pressed, the selected mode key will light, confirming your choice. Use the other keys to perform desired actions (see the following key chart). Turn on a device (e.g.,VCR) and, if applicable, insert media, (e.g., cassette or disc). 1. On the DRC450’s back, pull back the battery cover and remove it. 2. Use the two (2) supplied fullycharged AA alkaline batteries. Match their + and - marks to the + and - marks in the battery case, then insert the batteries. 3. 4. Push the battery cover back into place. 6. Test the unit by pressing POWER and any mode key (e.g., AUDIO, VCR/DVD, CABLE, or TV). If the batteries are inserted correctly, the selected mode key will be lit. TV Code: If your home entertainement device does not respond to the DRC450 after trying all of the codes listed for your brand, or if your brand is not listed at all, try searching for your code. Repeat steps 1 through 6 for each device you want to control. For example, after trying all of the codes for your TV, you still cannot get the DRC450 to operate your TV, then: On the DRC450, press and hold a mode key (i.e., AUDIO, VCR/DVD, CABLE, or TV) for at least 6 seconds, until you see the programming mode start. Each mode key light will turn off and on sequentially, starting with AUDIO on through TV, and the sequence will repeat twice. At this time, release the mode key and wait until it’s lit continuously. 2. 3. Locate the code for your device in Manufacturer’s Codes on the back of this user guide. Brands are listed in alphabetical order with the most popular codes listed first. 4. Enter the first four-digit code for your device. If you perform this procedure correctly, the selected mode key will blink three times. Aim the DRC450 at your device and press POWER once. The device should turn off. If it does not respond, repeat steps 2-4, trying each code listed for your brand until you find one that works. If it still does not work, try Searching For Your Code. 6. Device Type:______________ 5. Press POWER once. The TV key will light on and off, showing that an IR code has been sent. 5. If your television does not turn off, press the (Up) cursor key once again to call up the next IR code and press POWER once again. 6. 7. Aim the DRC450 at the TV/VCR combo and press POWER once. The device should turn off. If it does not respond, repeat steps 2-4, trying each code listed for your brand until you find one that works. If it still does not work, try Searching For Your Code. 8. 6. Repeat step 4 three more times for each successive digit by pressing and releasing 2, 3, and then 4. Finish writing down the TV code in the remaining TV code boxes. To check for the codes of your other devices, repeat steps 1 through 5, only substitute the appropriate mode key (i.e., VCR/DVD, CABLE, or AUDIO) for the device you are checking.Write down the codes in the appropriate device code boxes (see step 6 of Programming Device Control). When your television does turn off, a working code has been found. Press OK once to save the code and the TV key will blink three times, confirming the selection. To search for the codes of your other devices, repeat steps 1 through 7, but substitute the appropriate mode key (i.e., VCR/DVD, CABLE, or AUDIO) for the device you are searching for. Press and release VOLUME +. 3. The mode key’s light will blink three times, indicating volume has been locked to the selected mode. 4. Now, whenever you press VOLUME +, VOLUME -, or MUTE on the DRC450, volume will be controlled by selected mode, independent of the current mode. 1. On the DRC450, press and hold a mode key (at least 6 seconds) until you see the programming mode start. Each mode key light will turn off and on sequentially, starting with AUDIO on through TV, and the sequence will repeat twice. During this time, release the mode key and wait until it’s lit continuously. 2. Press and release VOLUME -. 3. The mode key light will blink three times, indicating volume has been unlocked for the selected mode. 4. Now, whenever you press VOLUME +, VOLUME -, or MUTE on the DRC450, the volume controls will reset to their original device. PROBLEM: A mode key does not blink or blinks 2 times when you press a key. SOLUTION: Replace the batteries with two (2) new AA alkaline batteries. PROBLEM: Changing the Volume Lock setting to the Cable,VCR/DVD, or TV mode will change the volume control for all modes except Audio, which will continue to control its own volume. If you change the Volume Lock setting to the Audio mode, all modes (i.e.,Audio., Cable, VCR/DVD, and TV) will be controlled by the Audio mode. A mode key blinks when you press a key, but home entertainment component does not respond. SOLUTION: Make sure the DRC450 is aimed at your home entertainment device and is not farther than 15 feet away. continued on back... Turn on your TV. Fold Fold Fold Fold Fold Fold 2. TROUBLESHOOTING NOTE: The selected mode will remain active until you press another mode key. Fold On the DRC450, press and hold a mode key (i.e., AUDIO, VCR/DVD, CABLE, or TV) for at least 6 seconds, until you see the programming mode start. Each mode key light will turn off and on sequentially, starting with AUDIO on through TV, and the sequence will repeat twice. At this time, release the mode key and wait until it’s lit continuously. To Unlock Volume Lock: Your new DRC450 is set to control the volume of a device through its associated mode (i.e., through the Motorola interactive digital terminal in the Cable mode, through the TV in the TV mode, through the VCR or DVD player in the VCR/DVD mode, and through the audio device in the Audio mode). If your TV is not remote controllable, or if you would like the volume to be controlled by a different device, you can change the Volume Lock setting to control a volume through a non-associated mode (e.g., through the Motorola interactive digital terminal in the TV mode). Perform the following procedure after you have set up your devices to find out which four-digit code is operating your equipment. For example, to find out which code is operating your TV: 1. 1. CHANGING VOLUME LOCK If your television still does not turn off, repeat step 5 as many times as needed until your TV turns off. If you have set up the DRC450 using the Searching For Your Code procedure, you may need to find out which four-digit code is operating your equipment. For future reference, write your device codes in the boxes below: To Change The Volume Lock Setting To Another Mode: NOTE: The mode key will not blink if the code digit is a “0”. CHECKING THE CODES TV Code (if used): Device Type:______________ Press the (Up) cursor key once to start the search mode. 4. TV/VCR Combo Code: VCR/DVD Code: To view the code for the first digit, press and release 1. Count the number of TV key blinks (e.g., 3 blinks = 3) and write down the number in the leftmost TV code box in step 6 of Programming Device Control. Locate the code for your device in Setup Codes For TV/VCR Combos on the back. Brands are listed in alphabetical order with the most popular codes listed first. NOTE: If you’ve located a TV/VCR code that works, but it has a separate TV code, you’ll also need to program it into DRC450 to access volume control. Perform the steps in “Programming Device Control” and use TV for the mode key (e.g., press and hold TV). AUDIO Code: 4. NOTE: In the search mode, the DRC450 will send IR codes from its library to the selected component, starting with the most popular codes first. When the device responds to a subsequent key command (e.g., POWER), the correct device code will be found. NOTE: If the device does not have a POWER key, press the (Play) key. For future reference, write your device code in the appropriate boxes below: On the DRC450, press and hold TV (at least 6 seconds) until you see the programming mode start. Each of the mode key lights will turn off and on sequentially, starting with AUDIO on through TV, and the sequence will repeat twice. During this time, release TV and wait until it’s lit continuously. 2. 3. Enter the first four-digit code for your device. If you perform this procedure correctly, VCR/DVD will blink three times. On the DRC450, press and hold TV (at least 6 seconds) until you see the mode light sequence start. Each of the mode key lights will turn off and on sequentially, starting with AUDIO on through TV, and will repeat twice. During the sequence, release the TV key and wait until it stays lit continually. Press 9 - 9 - 0. The TV key will blink three times. Turn on your TV. On the DRC450, press and hold a VCR/DVD for at least 6 seconds, until you see the programming mode start. Each mode key light will turn off and on sequentially, starting with AUDIO on through TV, and the sequence will repeat twice. At this time, release VCR/DVD and wait until it’s lit continuously. NOTE: If you enter an invalid code, VCR/DVD will turn off. Repeat steps 2 through 4 with a valid code. 5. 2. 3. 1. Turn on the TV/VCR Combo and insert a video cassette. Fold Fold SEARCHING FOR YOUR CODE NOTE: Please read steps 2-4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step 2. NOTE: If the device does not have a POWER key, press the (Play) key. NOTE: When a selected mode key blinks two times with each key press, this indicates that the batteries are getting low. Replace them within 20 minutes; otherwise the DRC450 may lose its settings and require reprogramming. Use the keypad (0 ~ 9) to directly select the channels (e.g., 09 or 031). Fold 1. NOTE: If you enter an invalid code, the selected mode key will turn off. Repeat steps 2 through 4 with a valid code. Use MENU to display the main menu. CABLE Code: PROGRAMMING TV/VCR COMBO CONTROL NOTE: Please read steps 2-4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step 2. Use OK**to chose menu options, PPV events, and to tune programs from the electronic program guide. Fold 7. NOTE: For programming TV/VCR Combo control, see the next section. In the CABLE mode, press DAY> (or
Source Exif Data:File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Create Date : 2002:10:02 12:04:45Z Modify Date : 2002:10:03 15:19:33-03:00 Page Count : 2 Creation Date : 2002:10:02 12:04:45Z Producer : Acrobat Distiller 4.0 for Macintosh Author : Roman Mod Date : 2002:10:03 15:19:33-03:00 Metadata Date : 2002:10:03 15:19:33-03:00 Creator : Roman Title : Moto DRC450_MnlEXIF Metadata provided by EXIF.tools