Motorola Personal Computer Mvme5100 Users Manual V5100a_ih4

2015-01-23

• Contents
• List of Figures
• List of Tables
• About This Manual
  • Summary of Changes
  • Overview of Contents
  • Comments and Suggestions
  • Conventions Used in This Manual
    • Terminology
• Hardware Preparation and Installation
  • Introduction
  • Getting Started
    • Overview and Equipment Requirements
    • Unpacking Instructions
  • Preparation
    • Hardware Configuration
    • Jumper Settings
      • PMC/SBC (761/IPMC) Mode Selection
    • Installation Considerations
  • Installation
    • PMC Modules
    • Primary PMCspan
    • Secondary PMCspan
    • MVME5100
• Operation
  • Introduction
  • Switches and Indicators
    • ABT/RST Switch
      • Abort Function
      • Reset Function
    • Status Indicators
      • RST Indicator (DS1)
      • CPU Indicator (DS2)
    • Connectors
      • 10/100 BASE T Ports
      • DEBUG Port
  • System Powerup
    • Initialization Process
• PPCBug Firmware
  • Introduction
  • PPCBug Overview
    • Implementation and Memory Requirements
  • Using PPCBug
    • Hardware and Firmware Initialization
  • Default Settings
    • CNFG - Configure Board Information Block
    • ENV - Set Environment
      • Configuring the PPCBug Parameters
    • LED/Serial Startup Diagnostic Codes
    • Configuring the VMEbus Interface
    • Firmware Command Buffer
  • Standard Commands
    • Diagnostics
• Functional Description
  • Introduction
  • Features Summary
  • Features Descriptions
    • General
    • Processor
    • System Memory Controller and PCI Host Bridge
    • Memory
      • Flash Memory
      • ECC SDRAM Memory
    • P2 Input/Output (I/O) Modes
    • Input/Output Interfaces
      • Ethernet Interface
      • VMEbus Interface
      • Asynchronous Communications
      • Real-Time Clock & NVRAM & Watchdog Timer
      • Timers
      • Interrupt Routing
      • IDSEL Routing
• Pin Assignments
  • Introduction
    • Summary
  • Jumper Settings
  • Connectors
    • IPMC761 Connector (J3) Pin Assignments
    • Memory Expansion Connector (J8) Pin Assignments
    • PCI Expansion Connector (J25) Pin Assignments
    • PCI Mezzanine Card (PMC) Connectors
    • VMEbus Connectors P1 & P2 Pin Assignments (PMC mode)
    • VMEbus P1 & P2 Connector Pin Assignments (SBC Mode)
    • 10 BaseT/100 BaseTx Connector Pin Assignments
    • COM1 and COM2 Connector Pin Assignments
• Programming the MVME51xx
  • Introduction
  • Memory Maps
    • Processor Bus Memory Map
      • Default Processor Memory Map
      • Processor Memory Map
      • PCI Memory Map
      • VME Memory Map
    • PCI Local Bus Memory Map
    • VMEbus Memory Map
  • Programming Considerations
    • PCI Arbitration
    • Interrupt Handling
    • DMA Channels
    • Sources of Reset
    • Endian Issues
      • Processor/Memory Domain
      • PCI Domain
      • VMEbus Domain
• Specifications
  • General Specifications
  • Power Requirements
  • Cooling Requirements
  • EMC Compliance
• Troubleshooting
  • Solving Startup Problems
• Related Documentation
  • Motorola Computer Group Documents
  • Manufacturers’ Documents
  • Related Specifications
• RAM500 Memory Expansion Module
  • Overview
  • Features
  • Functional Description
    • RAM500 Description
    • SROM
    • Host Clock Logic
  • RAM500 Module Installation
  • RAM500 Connectors
    • Bottom Side Memory Expansion Connector (P1)
    • Top Side Memory Expansion Connector (J1)
  • RAM500 Programming Issues
    • Serial Presence Detect (SPD) Data
• Thermal Analysis
  • Thermally Significant Components
  • Component Temperature Measurement
    • Preparation
    • Measuring Junction Temperature
    • Measuring Case Temperature
    • Measuring Local Air Temperature
• Index