Motorola Mvme5100 Series Users Manual VME Processor Modules Data Sheet

MVME5100 Series to the manual 75f088a5-d598-42fc-91b5-43fc508b08f7

: Motorola Motorola-Mvme5100-Series-Users-Manual-271494 motorola-mvme5100-series-users-manual-271494 motorola pdf

Open the PDF directly: View PDF .
Page Count: 5

TM

MVME5100 Series

VME Processor Modules

♦PowerPC 7400 or PowerPC 750™

microprocessor with 32KB/32KB L1 cache

♦Up to 2MB of secondary backside cache

♦100 MHz front-side bus

♦64MB, 128MB, or 512MB of on-board

ECC SDRAM—expandable up to 1GB

with optional RAM500 memory expansion

modules

♦Up to 17MB Flash memory

♦Dual IEEE P1386.1 compatible 32/64-bit

PMC expansion slots

♦64-bit PCI expansion mezzanine

connector allowing up to four more PMCs

♦Dual 16550 compatible async serial ports

♦Dual 10BaseT/100BaseTX Ethernet

♦32KB NVRAM and time-of-day clock with

replaceable battery backup

♦Four 32-bit timers, one watchdog timer

♦On-board debug monitor

♦Single VME slot even when fully

configured with two PMC modules and

both add-on memory mezzanines

Supercomputing levels of performance in a scalable, single-board

computer

The MVME5100 is a high-performance VME processor module featuring the

Motorola Computer Group (MCG) PowerPlus II architecture with a choice of

PowerPC® processors—either Motorola’s MPC7400 with AltiVec™ technol-

ogy for algorithmic-intensive computations or the low-power MPC750.

Based on an integrated PCI bridge–memory controller ASIC designed by

MCG, PowerPlus II takes memory performance to new levels with 582MB/s

memory read bandwidth and 640MB/s burst write bandwidth. Plus, Power-

Plus II architecture supports full PCI throughput of 264MB/s without starving

the CPU from its memory.

The MVME5100 is designed to meet the needs of OEMs servicing the military

and aerospace, industrial automation, and semiconductor process equipment

market segments.

MVME5100 P2 I/O

I/O Compatibility

Historically, MCG has offered two tracks in its PowerPC VME

portfolio. The first track (which includes the MVME2600/

2700) provides typical single-board computer I/O features

including Ethernet, SCSI, multiple serial ports, a parallel port,

and a single PMC slot. The on-board I/O is routed to P2 and

made available to the user via MCG’s MVME761 or

MVME712M transition boards. The second track (which

includes the MVME2300/2400) offers limited on-board I/O

(Ethernet and a single serial port both via the front panel) but

provides dual PMC slots enabling maximum user I/O custom-

ization.

The MVME5100 merges the best features of both tracks

enabling the OEM to support varying I/O requirements with

the same base platform, simplifying part number mainte-

nance, technical expertise requirements, and sparing.

P2 I/O Modes

The MVME5100 supports two, jumper-configurable P2 I/O

modes, PMC mode and IPMC mode.

PMC mode is backward compatible with the MVME2300/

MVME2400. In PMC mode, 64 pins from PMC Slot 1 and 46

pins from PMC Slot 2 are available on P2 for PMC rear I/O.

In IPMC mode, the MVME5100 supports legacy MVME761 or

MVME712M I/O modules (with limited PMC I/O) when an

IPMC761 or IPMC712 PMC card is populated in PMC Slot 1.

In this configuration, PMC Slot 2 contains some signals that

are reserved for extended SCSI.

IPMC Modules

The IPMC761 and IPMC712 are optional add-on PMC mod-

ules that provide backward compatibility with previous-gener-

ation MCG products (such as MVME2600 and MVME2700)

using the MVME761 or MVME712M transition board. IPMC

modules provide rear I/O support for

• one single-ended Ultra Wide SCSI port

• one parallel port

• four serial ports (2 or 3 async and 1 or 2 sync/async,

depending on module)

With this PMC card configuration, the memory mezzanine,

one PMC slot, and the PMCspan are still available, providing

support for OEM product customization.

Transition Modules

MVME761

The MVME761 transition module provides industry-standard

connector access to the IEEE 1284 parallel port, a 10BaseT

or 100BaseT port via an RJ-45 connector, two DB-9 connec-

tors providing access to the asynchronous serial ports config-

ured as EIA-574 DTE, and two HD-26 connectors providing

access to the sync/async serial ports. These serial ports,

labeled as Serial 3 and Serial 4 on the faceplate of the

MVME761, are individually user-configurable as EIA-232,

EIA-530, V.35, or X.21 DCE or DTE via the installation of

Motorola Serial Interface Modules (SIMs).

A P2 adapter provides interface module signals to the

MVME761 transition module. The 3-row P2 adapter can be

used for 8-bit SCSI. A 5-row P2 adapter supports 16-bit SCSI

and PMC I/O.

MVME712M

The MVME712M transition module provides industry-stan-

dard connector access to the Centronics® parallel port, a nar-

row SCSI port, and four DB-25 connectors providing access

to the asynchronous/synchronous serial ports jumper config-

urable as EIA-232 DCE or DTE. A P2 adapter provides inter-

ECC SDRAM

64, 128 or 512MB

64-bit/33 MHz Local PCI Bus

100 MHz Memory Bus

X-Bus

Serial

Hawk ASIC

Ethernet

82559ER

L2 Cache

1MB or 2MB

Flash

16MB

SDRAM Expansion

64 or 256MB

Flash

1MB

RTC

NVRAM

Serial

16550

BUF

RJ-45

VME

Universe2B

Ethernet

82559ER

MPC7400

MPC750

RJ-45

PCI

Expansion

P1P2

60x

Arbiter

SDRAM Expansion

256MB

RJ-45

Serial

16550

Vcore

REG

+3.3V

REG

PMC2 PMC1

FP I/OFP I/O

Rows A & C

64-pins

Rows D & Z

46-pins

COM1

COM2

Parallel

SER3 Sync (761) Async (712)

SER4 (Sync)

16-bit SCSI

PCI

P2 MUX

ISA

Super I/O

National

SCSI

LSI

PIB

WB-554

ESCC

85230 CIO

8536

P2 MUX

PAL

(IPMC761)

PMC P14 & P15

PMC P11 & P12

MVME5100 Block Diagram IPMC Block Diagram

MVME5100 P2 I/O

Transition Modules

face signals to the MVME712M transition module. The 3-row

P2 adapter can be used for 8-bit SCSI.

To gain access to the additional user definable I/O pins pro-

vided via the 5-row VME64 extension connector, a special P2

adapter board is available. This adapter panel replaces the

traditional 3-row P2 adapter and extends its capability by pro-

viding access to the PMC I/O pins.

Software Support

Firmware Monitor

Firmware must fulfill the traditional functions of test and initial-

ization and provide operating system boot support. The

MVME5100 firmware monitor exceeds these requirements

with a proven monitor from the embedded VME leader. It

expands features like power-up tests with extensive diagnos-

tics, as well as a powerful evaluation and debug tool for sim-

ple checkout or when high-level development debuggers

require additional support. All this is included with the

MVME5100 firmware; plus it supports booting both operating

systems and kernels.

Operating Systems and Kernels

MVME5100 supports booting a variety of operating systems

including a complete range of real-time operating systems

and kernels which may be purchased from the following com-

panies:

Specifications

MVME5100 Processor Module

Processor

Main Memory

Flash Memory

NVRAM

Counters/Timers

VMEbus ANSI/VITA 1-1994 VME64 (IEEE STD 1014)

Ethernet Interface

Asynchronous Serial Ports

Dual IEEE P1386.1 PCI Mezzanine Card Slots

Wind River Systems, Inc.: VxWorks®

Multiple Partners: Linux®

Microprocessor: MPC7400 MPC750

Clock Frequency: 400 MHz 450 MHz

On-chip Cache (I/D): 32K/32K 32K/32K

Secondary Cache: 1MB or 2MB 1MB

Type: PC100 ECC SDRAM with 100 MHz bus

Capacity: 64MB, 128MB, or 512MB on board,

expandable to 1GB with RAM500 mem-

ory mezzanines

Single Cycle Accesses: 10 Read/5 Write

Read Burst Mode: 7-1-1-1 idle; 2-1-1-1 aligned page hit

Write Burst Mode: 4-1-1-1 idle; 2-1-1-1 aligned page hit

Architecture: 64-bit, single interleave

Software Support

Specifications

MVME5100 Processor Module

Type: EEPROM, on-board programmable

Capacity: 1MB via two 32-pin PLCC/CLCC sockets;

16MB surface mount

Read Access (16MB

port): 70 clocks (32-byte burst)

Read Access (1MB

port): 262 clocks (32-byte burst)

Capacity: 32KB (4KB available for users)

Cell Storage Life: 50 years at 55° C

Cell Capacity Life: 5 years at 100% duty cycle, 25° C

Removable Battery: Yes

TOD Clock Device: M48T37V

Real-Time Timers/

Counters: Four, 32-bit programmable

Watchdog Timer: Time-out generates reset

Controller: Tundra Universe

DTB Master: A16–A32; D08–D64, BLT

DTB Slave: A24–A32; D08–D64, BLT, UAT

Arbiter: RR/PRI

Interrupt Handler/

Generator: IRQ 1–7/Any one of seven IRQs

System Controller: Yes, jumperable or auto detect

Location Monitor: Two, LMA32

Controller: Two Intel 82559ER

Interface Speed: 10/100Mb/s

PCI Local bus DMA: Yes, with PCI burst

Connector: One routed to front panel RJ-45, one

routed to front panel RJ-45 or optionally

routed to P2, RJ-45 on MVME761

Controller: 16C550C UART

Number of Ports: Two, 16550 compatible

Configuration: EIA-574 DTE

Async Baud Rate, bps

max.: 38.4K EIA-232, 115Kbps raw

Connector: One routed to front panel RJ-45, one on

planar for development use

Address/Data: A32/D32/D64, PMC PN1, PN2, PN3,

PN4 connectors

PCI Bus Clock: 33 MHz

Signaling: 5V

Power: +3.3V, +5V, ±12V; 7.5 watts maximum

per PMC slot

Module Types: Two single-wide or one double-wide, front

panel or P2 I/O

PCI Expansion Connector

Power Requirements

(not including power required by PMC or IMPC modules)

Board Size

IPMC Modules

PMC Interface

SCSI Bus

Synchronous Serial Ports

Asynchronous Serial Ports

Parallel Port

Power Requirements

(additional power load placed on MVME5100 with IPMC installed)

Transition Modules

I/O Connectors

Board Size

All Modules

Environmental

(Minimum of 400 LFM (linear feet per minute) of forced air cooling is

recommended for operation in the higher temperature ranges.)

Address/Data: A32/D32/D64

PCI Bus Clock: 33 MHz

Signaling: 5V

Connector: 114-pin connector located on the planar

of the MVME5100

+5V ± 5% +12V ± 10% –12V ± 10%

MVME5100: 3.0 A typ. 8.0 mA typ. 2.0 mA typ.

MVME5100 with

MVME761: 3.2 A typ.,

4.0 A max. 0.2 A typ.

0.5 A max. 0.1 A typ.

0.3 A max.

Height: 233.4 mm (9.2 in.)

Depth: 160.0 mm (6.3 in.)

Front Panel Height: 261.8 mm (10.3 in.)

Width: 19.8 mm (0.8 in.)

Max. Component

Height: 14.8 mm (0.58 in.)

Address/Data: A32/D32/D64, PMC PN1, PN2, PN3,

PN4 connectors

PCI Bus Clock: 33 MHz

Signaling: 5V

Module Type: Basic, single-wide; P2 I/O

Controller: Symbios 53C895A

PCI Local Bus DMA: Yes, with PCI local bus burst

Asynchronous (8-bit

mode): 5.0MB/s

Ultra SCSI: 20.0MB/s (8-bit mode), 40.0MB/s (16-bit

mode)

Note: 16-bit SCSI operation precludes the use of some PMC Slot 2

signals.

Controller: 85230/8536

Number of Ports: Two (IPMC761); one (IPMC712)

Configuration: IPMC761: TTL to P2 (both ports), SIM

configurable on MVME761;

IPMC712: EIA-232 to P2

Baud Rate, bps max.: 2.5M sync, 38.4K async

Oscillator Clock Rate

(PCLK): 10 MHz/5 MHz

Controller: 16C550 UART; 85230/8536

Number of Ports: Two (IPMC761); three (IPMC712)

Configuration: EIA-574 DTE (IPMC761);

EIA-232 (IPMC712)

Async Baud Rate, bps

max.: 38.4K EIA-232, 115Kbps raw

IPMC Modules

Controller: PC97307

Configuration: 8-bit bi-directional, full IEEE 1284 sup-

port; Centronics compatible (minus EPP

and ECP on MVME712M)

Modes: Master only

IPMC761 IPMC712

+5V: 0.5 A max. 0.5 A max.

+3.3V 0.75 A max. 0.75 A max.

MVME761 MVME712M

Asynchronous

Serial Ports: Two, DB-9 labeled as

COM1 and COM2 Three, DB-25 labeled

as Serial 1, Serial 2,

and Serial 3

Synchronous

Serial Ports: Two HD-26 labeled as

Serial 3 and Serial 4

(user configurable via

installation of SIMs),

Two 60-pin connectors

on MVME761 planar

for installation of two

SIMs

One, DB-25 labeled as

Serial 4

Parallel Port: HD-36, Centronics

compatible D-36, Centronics com-

patible

Ethernet: 10BaseT or

100BaseTX, RJ-45 not available

SCSI: 8- or 16-bit, 50- or 68-

pin connector via P2

adapter

8-bit, standard SCSI D-

50

Height: 233.4 mm (9.2 in.)

Depth: 80.0 mm (3.1 in.)

Front Panel Height: 261.8 mm (10.3 in.)

Front Panel Width: MVME761: 19.8 mm (0.8 in.)

MVME712M: 39.6 mm (1.6 in.)

Operating Nonoperating

Temperature: 0° C to +55° C

(inlet air temp. w/forced

air cooling)

–40° C to +85° C

Humidity (NC): 5% to 90% 5% to 90%

Vibration: 2 Gs RMS,

20–2000 Hz random 6 Gs RMS,

20–2000 Hz random

Transition Modules

All Modules

www.motorola.com/computer 1-800-759-1107

Motorola Computer Group Worldwide Headquarters: 2900 S. Diablo Way, Tempe, AZ 85282

Sales Offices:

United Kingdom:

+44 (0) 1256 790555 •

Asia Pacific and Japan:

852-2966-3210 •

France:

+33 (0) 1 64

86 64 24 •

Germany:

+49 (0) 611-3611 604 •

East Mediterranean:

972-3-568-4388 •

Canada & Central Pan America:

905-507-7200 •

Eastern Pan America:

508-357-8260 •

Western Pan America:

408-991-8634

Demonstrated MTBF

Safety

All printed wiring boards (PWBs) are manufactured with a flammabil-

ity rating of 94V-0 by UL recognized manufacturers.

Electromagnetic Compatibility (EMC)

Intended for use in systems meeting the following regulations:

This product was tested in a representative system to the following

standards:

Ordering Information

All models of the MVME5100 are available with either VME Scanbe

front panel (-01

x

1) or IEEE 1101 compatible front panel (-01

x

3).

I/O Modules

Related Products

Documentation

Documentation is available for online viewing and ordering at http://

www.motorola.com/computer/literature.

(based on a sample of eight boards in accelerated stress environ-

ment; results pending for IPMC712)

Mean: 190,509 hours

95% Confidence: 107,681 hours

U.S.: FCC Part 15, Subpart B, Class A (non-residential)

Canada: ICES-003, Class A (non-residential)

CE Mark per European EMC Directive 89/336/EEC with Amend-

ments; Emissions: EN55022 Class B; Immunity: EN55024

(results pending for configurations with IPMC712)

Part Number Description

MPC750 configurations with 450 MHz MPC750, 17MB Flash and

1MB L2 cache

MVME5100-013

x

64MB ECC SDRAM

MVME5100-016

x

512MB ECC SDRAM

MPC7400 configurations with 400 MHz MPC7400 and 17MB Flash

MVME5101-013

x

64MB ECC SDRAM, 1MB L2 cache

MVME5101-016

x

512MB ECC SDRAM, 1MB L2 cache

MVME5101-213

x

64MB ECC SDRAM, 2MB L2 cache

MVME5101-214

x

128MB ECC SDRAM, 2MB L2 cache

MVME5101-216

x

512MB ECC SDRAM, 2MB L2 cache

MVME712M Compatible I/O

IPMC712-001 Multifunction rear I/O PMC module; Ultra

Wide SCSI, one parallel port, three async and

one sync/async serial ports

MVME712M Transition module connectors: One DB-25

sync/async serial port, three DB-25 async

serial port, one AUI connector, one D-36 par-

allel port, and one 50-pin 8-bit SCSI; includes

3-row DIN P2 adapter module and cable

Ordering Information

MVME761 Compatible I/O

IPMC761-001 Multifunction rear I/O PMC module; Ultra

Wide SCSI, one parallel port, two async and

two sync/async serial ports

MVME761-001 Transition module: Two DB-9 async serial port

connectors, two HD-26 sync/async serial port

connectors, one HD-36 parallel port connec-

tor, one RJ-45 10/100 Ethernet connector;

includes 3-row DIN P2 adapter module and

cable (for 8-bit SCSI)

MVME761-011 Transition module: Two DB-9 async serial port

connectors, two HD-26 sync/async serial port

connectors, one HD-36 parallel port connec-

tor, and one RJ-45 10/100 Ethernet connec-

tor; includes 5-row DIN P2 adapter module

and cable (for 16-bit SCSI); requires back-

plane with 5-row DIN connectors

SIM232DCE or DTE EIA-232 DCE or DTE Serial Interface Module

SIM530DCE or DTE EIA-530 DCE or DTE Serial Interface Module

SIMV35DCE or DTE V.35 DCE or DTE Module

SIMX21DCE or DTE X.21 DCE or DTE Serial Interface Module

PMCSPAN-002 Primary 32-bit PCI expansion, mates directly

to the MVME5100 providing slots for either

two single-wide or one double-wide PMC

cards; optional PMCSPAN-010

PMCSPAN-010 Secondary 32-bit PCI expansion, plugs

directly into PMCSPAN-002 providing two

additional PMC slots

RAM500-004 Stackable (top) 64MB ECC SDRAM mezza-

nine

RAM500-006 Stackable (top) 256MB ECC SDRAM mezza-

nine

RAM500-016 Stackable (bottom) 256MB ECC SDRAM

mezzanine

V5100A/IH MVME5100 Installation and Use

V5100A/PG Programmer’s Reference Guide

VME761A/IH MVME761 Transition Module Installation and

Use

VME712MA/IH MVME712 Transition Module Installation and

Use

PPCBUGA1/UM

PPCBUGA2/UM PPCBug Firmware Package User’s Manual

(volumes one and two)

PPCDIAA/UM PPCBug Diagnostics Manual

Motorola and the stylized M logo are registered trademarks and the Intelligence Everywhere logo, AltiVec, Digital DNA and the Digital DNA logo are trademarks of Motorola, Inc. PowerPC and

the PowerPC logo are registered trademarks and PowerPC 750 is a trademark of International Business Machines Corporation and are used by Motorola, Inc. under license from International

Business Machines Corporation. VxWorks is a registered trademark of Wind River Systems, Inc. Linux is a registered trademark of Linus Torvalds. Centronics is a registered trademark of

Centronics Data Computer Corporation. All other product or service names are the property of their respective owners.

This datasheet identifies products, their specifications, and their characteristics, which may be suitable for certain applications. It does not constitute an offer to sell or a commitment of present

or future availability, and should not be relied upon to state the terms and conditions, including warranties and disclaimers thereof, on which Motorola may sell products. A prospective buyer

should exercise its own independent judgement to confirm the suitability of the products for particular applications. Motorola reserves the right to make changes, without notice, to any products

or information herein which will, in its sole discretion, improve reliability, function, or design. Motorola does not assume any liability arising out of the application or use of any product or circuit

described herein; neither does it convey any license under its patent or other intellectual property rights or under others. This disclaimer extends to any prospective buyer, and it includes

Motorola’s licensee, licensee’s transferees, and licensee’s customers and users. Availability of some of the products and services described herein may be restricted in some locations.

® Reg. U.S. Pat. & Tm. Off. © 1999, 2000, 2001 Motorola, Inc. All rights reserved. M5100-D8 9/01