Motorola Symbol Ds3578 Users Manual Quick Start Guide, P/n 72 111604 02 Rev B

: Motorola Motorola-Symbol-Ds3578-Users-Manual-120705 motorola-symbol-ds3578-users-manual-120705 motorola pdf

Open the PDF directly: View PDF .
Page Count: 2

BLACK

PANTONE 285

DS3578 Poster

SYMBOL DS3578

DS3578 Poster

1234

4

2

3

1

2

Quick Start Guide

POST IN WORK AREAPOST IN WORK AREA

Cradle Insertion

BATTERY INSERTION/REMOVAL

IBM 46XX

USB

RS-232

Cable Connection at Cradle

Keyboard Wedge

No power to scanner

Check battery

End cap not secured correctly

Turn end cap to secure

Scanner not working

Bar code unreadable

Ensure bar code is not defaced;

try scanning test bar code of same

bar code type

Scanner not programmed

for bar code type

Ensure scanner is programmed

to read type of bar code being

scanned

Scanner not decoding bar code

Scanner not paired to host-connected cradle

Pair the scanner to the cradle (using the

PAIR bar code on the cradle)

Cradle not programmed for correct host interface

Check scanner host parameters or

edit options

Interface cable is loose

Check for loose cable

connections

Scanner decoding bar code, but data not transmitting to host

Paired cradle host communication parameters do not match the host’s parameters

Check cradle host parameters or edit options

Scanned data incorrectly displayed on host

Set Defaults

Note: The scanner connection to the cradle

is dissolved when Set Defaults is scanned.

RS-232 Host Types

Carriage Return/Line Feed

Keyboard Wedge Host Types

USB Host Types

IBM 46XX Host Types Radio Communications Host Types

SET DEFAULTS

HID KEYBOARD EMULATION

IBM HAND-HELD USB

PORT 5B

PORT 9B

STANDARD RS-232

ICL RS-232

NIXDORF RS-232 MODE A

Unpairing/Disconnection

UNPAIR/DISCONNECT

SCAN OPTIONS

<DATA><SUFFIX>

ENTER

NIXDORF RS-232 MODE B

FUJITSU RS-232 OPOS/JPOS

IBM PC/AT and IBM PC COMPATIBLE

Please refer to the Symbol DS3578 Product Reference Guide Troubleshooting section for further information.

If data is still not transmitting to host, it may be necessary to recycle power on the cradle.

Or use coin Or use coin

Host

Power

See Product Reference Guide for more information

CRADLE HOST

SERIAL PORT PROFILE (SLAVE)

BLUETOOTH KEYBOARD EMULATION (HID SLAVE)

Caution: Symbol DS3478 cordless scanners are incompatible with

Symbol STB3508/3578 cradles. Symbol DS3578 cordless scanners are

incompatible with Symbol STB3408/3478 cradles.

SERIAL PORT PROFILE (MASTER)

1 Tether Plate

2 LED Indicators

3 Scan Window

4 Scan Trigger

HOST INTERFACES

TROUBLESHOOTING

SYMBOL DS3578 PROGRAMMING BAR CODES

NOTE: Cables may vary depending on configuration. When using an external power supply, place the

ferrite core on the power cable, insert the power supply cable into the cradle, then insert the

host cable. Connect AC power last.

Ferrite Core

DS3578 PosterDS3578 Poster

PERF PERF

BLACK

PANTONE 285

SYMBOL DS3578

SYMBOL DS3578

4

3

1

2

2

012345

012345

012345

012345

OPTIMUM UPRIGHT BODY POSTURE

Low-medium-high beeps

Power up

Normal beep

Bar code decoded [if

decode beeper enabled]

4 long low beeps

Transmission error

detected; data is ignored

4 short high beeps

Low battery

indication

Short low-high beeps

Scanner has paired with

the cradle

Short high-low beeps

Scanner has unpaired

with the cradle

Standard Use

Long low-high beeps

Input error, incorrect programming

sequence,or Cancel bar code scanned

High-low-high-low beeps

Successful program exit with change

in the parameter setting

Parameter Menu Scanning

Beeper Indications

Standard Use

LED Indications

Off

No power applied to scanner (battery

discharged or removed), or scanner

is in low power and ready to scan

Green

Bar code successfully

decoded

Red

Data transmission

error or scanner malfunction

or Symbol DS3578 scanner

inserted into an STB3478

cradle

Charging Use

Green Slow Flash

Scanner charging at

a slow rate (used

when cradle is

powered by host cable)

Green Fast Flash

Scanner charging at a

fastrate (used when

cradleis powered from

external power supply)

Red and Green Flash

Temperature fault

Red Flash

Charging problem

See Product Reference

Guide for more

information

Recommended Usage Guide

OPTIMUM SCANNING POSITIONS

TAKING BREAKS AND TASK ROTATION RECOMMENDEDTAKING BREAKS AND TASK ROTATION RECOMMENDED

ALTERNATE LEFT AND RIGHT HANDSALTERNATE LEFT AND RIGHT HANDS

Aiming

1 Tether Plate

2 LED Indicators

3 Scan Window

4 Scan Trigger

Optimum body posture

for low scanning

OPTIMUM BODY POSTURE

Alternate left

and right knees

Optimum body posture for

extended range scanning

72E-111604-02

Revision B February 2010

REGULATORY INFORMATION

AVOID EXTREME

WRIST ANGLES

AVOID REACHING

AVOID BENDING

Long low-high beeps or

Long low-high-low-high beeps

Unsuccessful pairing attempt

LED Indicator

POST IN WORK AREAPOST IN WORK AREA

SYMBOL DS3578

Quick Start Guide

Wireless Device Country Approvals

Regulatory markings, subject to certification, are applied to the device signifying the radio(s) are approved for

use in the following countries: United States, Canada, Japan, China, S. Korea, Australia, & Europe1.

Please refer to the Symbol Declaration of Conformity (DoC) for details of other country markings. This is

available at http://www.motorola.com/enterprise/doc.

Note1: For 2.4GHz or 5GHz Products: Europe includes, Austria, Belgium, Bulgaria, Czech Republic, Cyprus,

Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein,

Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia,

Spain, Sweden, Switzerland and the United Kingdom.

Radio Modules

This device contains approved radio module(s). These module(s) are identified below.

Symbol Bluetooth radio Type: LMX5452

Bluetooth Wireless Technology

This is an approved Bluetooth product. For more information or to view End Product Listing, please visit

https://www.bluetooth.org/tpg/listings.cfm

Other Countries

Declarações Regulamentares para Symbol DS3578 BRAZIL

NOTA: A marca de certificação se aplica ao Equip. de Radiação Restrita, modelo Symbol DS3578.

Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo

de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário.”

Para maiores consultas sobre ANATEL consulte o site: www.anatel.gov.br

CHILE

“Este equipo cumple con la Resolución No 403 de 2008, de la Subsecretaria de telecomunicaciones, relativa a radiaciones

electromagnéticas.”.

Taiwan

臺灣

低功率電波輻射性電機管理辦法

第十二條

經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或

變更原設計之特性及功能。

第十四條

低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改

善至無干擾時方得繼續使用。

前項合法通信，指依電信規定作業之無線電通信。

低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

Korea

For a radio equipment using 2400~2483.5MHz or 5725~5825MHz, the following two expression should be displayed ;

당해 무선설비는 운용 중 전파혼신 가능성이 있음

당해 무선설비 는전파혼 신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다.

Laser Devices

Complies with 21CFR1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, June 24, 2007 and

EN60825-1:2007 and IEC 60825-1(ED.2). The laser classification is marked on one of the labels on the device.

Class 1 Laser devices are not considered to be hazardous when used for their intended purpose. The following statement

is required to comply with US and international regulations:

Caution: Use of controls, adjustments or performance of procedures other than those specified herein may result in

hazardous laser light exposure.

Class 2 laser scanners use a low power, visible light diode. As with any very bright light source, such as the sun, the user

should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known to be harmful.

RF Exposure Guidelines

Safety Information

Reducing RF Exposure – Use Properly

Only operate the device in accordance with the instructions supplied.

International

The device complies with internationally recognized standards covering human exposure to electromagnetic fields from

radio devices. For information on “International” human exposure to eletromagnic fields refer to the Motorola/Symbol

Declaration of Conformity (DoC) at http://www2.symbol.com/doc/.

EU - Handheld Devices

To comply with EU RF exposure requirements, this device must be operated in the hand with a minimum separation

distance of 20cm or more from a person’s body. Other operating configurations should be avoided.

US and Canada - Handheld Devices

To comply with FCC RF exposure requirements, this device must be operated in the hand with a minimum separation

distance of 20 cm or more from a person’s body. Other operating configurations should be avoided.

Power Supply

Use only a Motorola/Symbol approved power supply output rated at 9Vdc and minimum 2A. The power supply shall be Listed

to UL/CSA 60950-1; and certified to IEC60950-1 and EN60950-1 with SELV outputs. Use of alternative power supply will

invalidate any approval given to this device and may be dangerous.

Batteries

Taiwan - Recycling

EPA (Environmental Protection Administration) requires dry battery producing or importing firms in accordance

with Article 15 of the Waste Disposal Act are required to indicate the recycling marks on the batteries used in

sales, giveaway or promotion. Contact a qualified Taiwanese recycler for proper battery disposal.

Battery Information

Motorola/Symbol rechargeable battery packs are designed and constructed to the highest standards within the industry.

However, there are limitations to how long a battery can operate or be stored before needing replacement. Many factors

affect the actual life cycle of a battery pack, such as heat, cold, harsh environmental conditions and severe drops.

When batteries are stored over six (6) months, some irreversible deterioration in overall battery quality may occur. Store

batteries at half of full charge in a dry, cool place, removed from the equipment to prevent loss of capacity, rusting of

metallic parts and electrolyte leakage. When storing batteries for one year or longer, the charge level should be verified at

least once a year and charged to half of full charge.

Replace the battery when a significant loss of run time is detected.

Standard warranty period for all Symbol batteries is 12 months, regardless if the battery was purchased separately or

included as part of the mobile computer or bar code scanner. For more information on Symbol batteries, please visit:

http:/mysymbolcare.symbol.com/battery/batbasics1.html.

Battery Safety Guidelines

• The area in which the units are charged should be clear of debris and combustible materials or chemicals.

Particular care should be taken where the device is charged in a non commercial environment.

• Follow battery usage, storage, and charging guidelines found in the user's guide.

• Improper battery use may result in a fire, explosion, or other hazard.

• To charge the mobile device battery, the battery and charger temperatures must be

between +32 º F and +104 º F (0 º C and +40 º C)

• Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a risk

of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or

a charger, contact Motorola Enterprise Mobility support.

• For devices that utilize a USB port as a charging source, the device shall only be connected to products that

bear the USB-IF logo or have completed the USB-IF compliance program.

• Do not disassemble or open, crush, bend or deform, puncture, or shred.

• Severe impact from dropping any battery-operated device on a hard surface could cause the battery to overheat.

• Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.

• Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water

or other liquids, or expose to fire, explosion, or other hazard.

• Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or

near a radiator or other heat source. Do not place battery into a microwave oven or dryer.

• Battery usage by children should be supervised.

• Please follow local regulations to promptly dispose of used re-chargeable batteries.

• Do not dispose of batteries in fire.

• Seek medical advice immediately if a battery has been swallowed.

• In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has

been made, wash the affected area with large amounts of water and seek medical advice.

• If you suspect damage to your equipment or battery, contact Motorola Enterprise Mobility support to arrange

for inspection.

Radio Frequency Interference Requirements - FCC

Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

FOR HOME OR OFFICE USE

Regulatory Information

This device is approved under the Symbol Technologies brand: Symbol Technologies, Inc. is the Enterprise Mobility

business of Motorola, Inc. ("Motorola"). This guide applies to Model Number DS3578

All Motorola/Symbol devices are designed to be compliant with rules and regulations in locations they are sold and

will be labeled as required. Local language translations are available at the following

website: http://www.motorola.com/enterprisemobility/manuals. Any changes or modifications to Motorola/Symbol

equipment, not expressly approved by Motorola/Symbol, could void the user's authority to operate the equipment.

CAUTION:

Only use Motorola/Symbol approved and UL Listed accessories, battery packs and battery chargers.

Avoid Extreme Wrist Angles

http://www.motorola.com/ds3578

MOTOROLA and the Stylized M Logo and Symbol and the Symbol logo are registered in the U.S. Patent and Trademark Office.

All other product or service names are the property of their respective owners. © Motorola, Inc. 2010

Motorola, Inc. One Motorola Plaza Holtsville, New York 11742, USA • 1-800-927-9626

Available at the following website: www.motorola.com/enterprisemobility/support

© MOTOROLA, INC. 2010 All rights reserved.

Motorola reserves the right to make changes to any product to improve reliability, function, or design.

Motorola does not assume any product liability arising out of, or in connection with, the application or use of any

product, circuit, or application described herein.

No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent,

covering or relating to any combination, system, apparatus, machine, material, method, or process in which Motorola

products might be used. An implied license exists only for equipment, circuits, and subsystems contained in Motorola

products.

MOTOROLA, the Stylized M Logo and Symbol and the Symbol logo are registered trademarks of Motorola, Inc. Other

product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and

are hereby acknowledged.

Motorola, Inc.

One Motorola Plaza

Holtsville, N.Y. 11742-1300

www.motorola.com/enterprisemobility

Warranty

For the complete Motorola hardware product warranty statement, go to:

http://www.motorola.com/enterprisemobility/warranty.

Patents

This product is covered by one or more patents. For patent information go to:

http:// www.motorola.com/enterprisemobility/patents.

Ergonomic Recommendations

Caution: In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below. Consult

with your local Health & Safety Manager to ensure that you are adhering to your company's safety programs to prevent

employee injury.

• Reduce or eliminate repetitive motion • Reduce or eliminate vibration

• Maintain a natural/neutral position • Reduce or eliminate direct pressure

• Reduce or eliminate excessive force • Provide adjustable workstations

• Keep objects that are used frequently • Provide adequate clearance

within easy reach • Provide a suitable working environment

• Perform tasks at correct heights • Improve work procedures

Service Information

If you have a problem using the equipment, contact your facility’s Technical or Systems Support. If there is a problem

with the equipment, they will contact the Motorola Enterprise Mobility Support at:

http://www.motorola.com/enterprisemobility/contactsupport.

For the latest version of this guide go to: http://www.motorola.com/enterprisemobility/manuals.

Please observe all warning notices with regard to the usage of wireless devices.

Potentially Hazardous Atmospheres – Vehicles Use

You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc.

and areas where the air contains chemicals or particles (such as grain, dust, or metal powders) and any other area

where you would normally be advised to turn off your vehicle engine.

Potentially Hazardous Atmospheres – Fixed Installations

You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc.

and areas where the air contains chemicals or particles (such as grain, dust, or metal powders).

Safety in Aircraft

Switch off your wireless device whenever you are instructed to do so by airport or airline staff. If your device offers

a ‘flight mode’ or similar feature, consult airline staff as to its use in flight.

Safety in Hospitals

Wireless devices transmit radio frequency energy and may affect medical electrical equipment.

Wireless devices should be switched off wherever you are requested to do so in hospitals, clinics or health care

facilities. These requests are designed to prevent possible interference with sensitive medical equipmet.

Pacemakers

Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a handheld

wireless device and a pacemaker to avoid potential interference with the pacemaker. These recommendations

are consistent with independent research and recommendations by Wireless Technology Research.

Persons with Pacemakers:

• Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON.

• Should not carry the device in a breast pocket.

• Should use the ear furthest from the pacemaker to minimise the potential for interference

• If you have any reason to suspect that interference is taking place, turn OFF your device.

Other Medical Devices

Please consult your physician or the manufacturer of the medical device, to determine if the operation of your

wireless product may interfere with the medical device.

Warnings for Use of Wireless Devices

Radio Transmitters (Part 15)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation.

Radio Frequency Interference Requirements – Canada

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Marking and European Economic Area (EEA)

Bluetooth® Wireless Technology for use through the EEA has the following restrictions:

• Maximum radiated transmit power of 100mW EIRP in the frequency range 2.400 -2.4835 GHz

• France, outside usage is restricted to 10mW EIRP

• Italy requires a user license for outside usage.

Statement of Compliance

Motorola/Symbol hereby, declares that this device is in compliance with the essential requirements and other

relevant provisions of Directives 1999/5/EC. Declaration of Conformities may be obtained from

www.motorola.com/enterprisemobility/doc/.

Japan (VCCI) - Voluntary Control Council for Interference

この装置は、情報処理装置等電波障害自主規制協議会（ＶＣＣＩ）の基準に基づくクラスB情報技術装置です。この

装置は、家庭環境で使用することを目的としていますが、この装置がラジオやテレビジョン受信機に近接して使用さ

れると、受信障害を引き起こすことがあります。 取扱説明書に従って正しい取り扱いをして下さい。

This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information

Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause

radio interference. Install and use the equipment according to the instruction manual.

Korean Warning Statement for Class B ITE

CAUTION - CLASS 2 LASER LIGHT WHEN OPEN. DO NOT STARE

INTO THE BEAM. ATTENTION-LUMIÈRE LASER EN CAS D'OUVERTURE .

NE PAS REGARDER DANS LE FAISCEAU. VORSICHT - LASERLICHT

KLASSE 2, WENN ABDECKUNG GEÖFFNET. NICHT DEM STRAH

L

BLICKEN. SEE QUICK REFERENCE GUIDE FOR PATENT INFORMATION.

COMPLIES WITH 21CFR1040.10 AND 1040.11

EXCEPT FOR DEVIATIONS

PURSUANT TO LASER NOTICE No. 50, DATED JUNE 24, 2007,

EN60825-1:2007 AND IEC 60825-1(ED.2) THIS CLASS B DIGITAL

APPARATUS COMPLIES WITH CANADIAN ICES-103. CET APPAREIL

NUMÉRIQUE DE LA CLASSE B EST CONFORME À LA NORME

NMB-003 DU CANADA. SEE PRODUCT GUIDE FOR PATENT INFO

XXXXXXXXXX

LASER LIGHT- DO NOT STARE INTO BEAM . CLASS 2

LASER PRODUCT. LASERLICHT -

NICHT IN DEN

STRAHL BLICKEN. LASER KLASSE 2. LUMIÈRE

LASER - NE PAS

REGARDER DANS LE FAISCEAU.

APPAREIL À LASER DE CLASSE 2 630-680nm, 1mW

P/N: DS3578-XXXXXXXXXX

BD_ADDR: XXXXXXXXXXXXX

(S)SN: XXXXXXXXXXXXX

MFD: XXXXXXX XXXX

SN BAR CODE

SYMBOL TECH INC. N.Y.

FCC ID: H9PLMX5452

IC: 1549D-LMX5452

0168

THIS DEVICE CONTAINS AN

APPROVED RADIO MODULE LMX5452

MODEL:DS3578

50

CMIIT ID: XXXXXXXXX

R003WWA080669

CCXXxxYYyyyZzW

XXXXXX

條碼掃描器

MADE IN XXXXXX

Aiming

Български:

Waste Electrical and Electronic Equipment (WEEE)

Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme için

Motorola'ya iade edilmelidir. Ürünlerin nasıl iade edileceği hakkında bilgi için lütfen şu

adresi ziyaret edin: http://www.motorola.com/recycle/weee.