Mountain Buggy Breeze Single B1204 Users Manual
Breeze Single-B1204 to the manual a8ab3d85-6c9d-4aea-b68e-643093bdf7c1
2015-02-09
: Mountain-Buggy Mountain-Buggy-Breeze-Single-B1204-Users-Manual-557654 mountain-buggy-breeze-single-b1204-users-manual-557654 mountain-buggy pdf
Open the PDF directly: View PDF 
.
Page Count: 11
| Download | |
| Open PDF In Browser | View PDF |
INSTRUCTIONS: For the following model Mountain Buggy® strollers: Urban Single - U1204 Urban Double - U2204 Terrain Single - T1204 Terrain Double - T2204 Urban Triple - U3204 Breeze Single - B1204 Note: Model and accessory availability may vary from country to country. Contents Pg Safety Instructions .................................................................................. 3 Operation (Wheel Assembly etc) ............................................................. 4 Operation (Folding, Brake, Wrist Strap) .................................................. 5 Operation (Safety Harness, Seat Adjustment) ........................................ 6 Operation (Seat, Sunhood, Storm Cover, Sun Cover) ............................. 7 Care and Maintenance ............................................................................ 8 Parts of Stroller Frame ............................................................................ 9 Accessories ........................................................................................... 10 Warranty Conditions ................................................................................11 Warranty Registration Card .................................................................... 12 We take safety seriously. Compliance with safety standards for baby strollers is NOT compulsory in all countries. All Mountain Buggy® models, including when a Carrycot and Carseat Clip are attached, have passed the Australian/New Zealand Safety Standard AS/NZS 2088, and the British Standard BS 7409. Models sold in North America have also passed American Standard ASTM F833. Designed and made in New Zealand for Mountain Buggy® Ltd. Manufactured by Tritec Manufacturing Ltd, an ISO9002 credited supplier. IMPORTANT KEEP FOR FUTURE REFERENCE Read these instructions carefully before use and keep for future reference. Your child’s safety may be affected if you do not follow these instructions. Safety Instructions WARNING: Never leave your child unattended. WARNING: Avoid serious injury from falling or sliding out. Use the harness at all times. Always use the crotch strap in combination with the waist belt. WARNING: A CHILD’S SAFETY IS YOUR RESPONSIBILITY. WARNING: FOLLOW THE MANUFACTURER’S INSTRUCTIONS. WARNING: DO NOT CARRY EXTRA CHILDREN OR BAGS ON THIS STROLLER/ PRAM. WARNING: MAKE SURE CHILDREN ARE CLEAR OF ANY MOVING PARTS IF YOU ADJUST THIS STROLLER/ PRAM, OTHERWISE THEY MAY BE INJURED. WARNING: CARE MUST BE TAKEN WHEN FOLDING AND UNFOLDING THE STROLLER TO PREVENT FINGER ENTRAPMENT. Ensure freedom of movement of locking devices. For all models, the seat is suitable for newborn up to 4 years old (3 years for the Breeze) or maximum of 35kg/77lb. For use with a newborn (0-6mths) the seat should be reclined fully. It is recommended that a newborn headrest or similar is used for babies 0-3 months. Other newborn options include: 1. Mountain Buggy® Carrycot (available for all models except Breeze) 2. Mountain Buggy ® Carseat Clip (available for all single models, except Breeze) Overloading, incorrect folding and the use of non-approved accessories may damage or break this stroller. Please note it is unsafe to use accessories other than those approved by the manufacturer or distributor. This stroller is designed for one child in each seat. WARNING: Any load attached to the handle affects the stability of the stroller. To prevent the stroller from becoming unstable, do not place parcels or accessory items anywhere except in storage basket and pockets provided. Maximum seat loading for all model strollers (including Double & Triple models) is 35kg/77lb. Maximum seat height capacity is 100cm. Maximum loading for the storage basket is 5kgs/11lb. Maximum loading for the pocket is 300gms/10.5oz (i.e. small items such as keys, wallets only). Excessive weight may cause a hazardous unstable condition to exist. Do not use near an open fire or exposed flame. Cover the stroller if it is exposed to sunlight through glass, for example in a car to avoid over heating. Remove plastic wrapping and discard to avoid a child suffocating. 3 Operation FRONT WHEEL ASSEMBLY REAR WHEEL ASSEMBLY ALL MODELS ALL MODELS 1. Holding both knobs at the same time, unscrew and pull out front axle. 2. Insert front wheel(s). FRONT WHEELS HAVE NO BRAKE COG. 3. Re-insert axle and finger tighten both knobs. brake cog brake cog 21 Check that brake cog is on the inside next to stroller frame. axle 2 Slide wheels onto each end of the axle. URBAN SINGLE, DOUBLE & TRIPLE brake cog brake lever 3 knob axle INSERT AXLE knob TIGHTEN KNOBS 4 Push each wheel on until it clicks Finished assembly. Push down on into place. Pull wheels to check brake lever to apply brakes. Check brake lever inserts into brake cog on they are secure. both sides. DO NOT use stroller if brakes are not functioning. ERECTING THE STROLLER TERRAIN & BREEZE SINGLE 1 Grip stroller near sunhood joints, and lift. axle knob INSERT AXLE knob TIGHTEN KNOBS 2 Place pressure on heel rest to ensure sliding locks are fully engaged. WARNING: Ensure that all locking devices are engaged before use. SWIVELLING FRONT WHEELS TERRAIN DOUBLE URBAN Locking the front wheel swivel(s) is recommended for use on uneven ground. There is still a small amount of left and right movement when in the locked position. axle spacer INSERT AXLE. Also insert spacer between front wheels. Knob knob TIGHTEN KNOBS knob Knob TO LOCK: Turn knob so locked TO UNLOCK: Turn knob symbol is at the top.Then 1/4 of a turn so ‘Unlocked’ swivel wheel under stroller until symbol is at the top. it locks into place. WARNING: TIGHTEN ALL KNOBS AND REGULARLY CHECK THEY REMAIN FIRM. 4 Operation FOLDING THE STROLLER REMOVING REAR WHEELS URBAN De-press quick release clip and slide wheel off axle. NOTE: On Urban model strollers, ensure front wheels are unlocked and rotated forward before folding. X X WRONG BRAKE brake lever CORRECT ALL MODELS brake lever To apply brake, push brake To release brake, lift brake lever completely down. lever completely up. Adjustable Handle WARNING: PUT ON THE BRAKE W H E N E V E R Y O U PA R K T H E STROLLER/PRAM. ENSURE THE 1 2 Fold adjustable handle Pull up sliding lock on both BRAKE IS ON WHEN LOADING AND sides of heel rest. (if applicable). UNLOADING CHILDREN. Sliding Lock SAFETY WRIST STRAP 3 4 Lift at heel rest so the handle bar end goes down. Fully folded. For an even flatter fold, remove wheels (see wheel removal). wrist strap Care should be taken if the stroller is used on stairs, escalators, down hills NOTE: Sliding lock on the left side has a secondary or in strong winds. safety catch. Hold the safety wrist strap firmly in all these situations. WARNING: MAKE SURE CHILDREN Regularly check that the wrist strap ARE CLEAR OF ANY MOVING PARTS is securely attached to the stroller WHEN FOLDING OR ERECTING handlebar and stitching is secure and THE STROLLER. strong. 5 Operation SAFETY HARNESS SEAT ANGLE TERRAIN ZIP HAMMOCK OPTION A push D The Zip Hammock has two seat back positions. Seat back is upright when zips are up, and reclined when zips are down. E B clip here C 2 1 To fasten waist strap push both buckle ends A & B into the crotch buckle C. sliding buckles Clip shoulder straps D & E to waist strap buckles. ADJUSTING SHOULDER STRAP HEIGHT Shoulder straps should be insertion slit adjusted so they are located 1 buckle just below or level with a child’s shoulders. The older 2 the child, the further up the 3 seat these straps will go. sliding buckles shoulder straps 3 4 Adjust sliding buckles so the harness straps are a firm fit. 5 Move sliding buckles To release, press up as far as possible s i d e s o f c e n t re to reduce the amount buckle. of strap hanging loose, eliminating the risk of chocking. strap buckle short side To locate buckle when adjusting straps, slip your hand up the inside back of the seat (or inside the pocket on the Zip Hammock model). A separate safety harness conforming to British Standard BS6684 may be attached to the two “D” rings located at the insertion of the waist harness. SEAT ANGLE ALL MODELS Seat back can be reclined to any point between upright and fully reclined position. buckles strap REMOVING With a hand inside the back of the seat rotate the rectangular shaped buckle and push short side through the insertion slot, while pulling strap at the front. POSITION OF CHILD IN SEAT X To adjust: Pull on buckles to Shows upright through to slide straps through buckles fully reclined seat angle. and recline seat. Pull straps through buckles to raise seat angle. NOTE: The stroller would become unstable if a child was to move up the seat. For this reason the seat retains a slight angle to prevent the stroller from tipping back. 6 INSERTING Re-thread short side of buckle through the most suitable insertion slot for your child. Once buckle is through, turn so it is flat against seat back, and check it is secure by pulling on strap. CORRECT XWRONG Make sure baby is positioned down as far as possible in seat. Operation REMOVING SEAT REMOVING SUNHOOD ALL MODELS ALL MODELS 1 Unfasten seat from frame along side tubes. sunhood support wire plastic joint B 1 Pull support wire out of sunhood joint, while pushing against frame. Note:This operation is child proof and therefore requires a degree of force. A URBAN 2 Unfasten strap underneath seat at point A. Unfasten frame straps at point B. TERRAIN 2 Push seat forward, then slide fabric up seat support wire. 2 Repeat step 1 on other side. 3 Unfasten the sunhood fabric from the stroller frame and seat near the handle bar. REFITTING SUNHOOD Place sunhood in position and push one side of wire into plastic joint. Repeat on other side by pulling wire away from frame at the top. Fasten sunhood fabric to stroller frame and seat, near handle bar. seat support wire 3 Remove seat support wire from stroller frame at C and D. C D REFITTING SEAT ALL MODELS STORM COVER AND SUN COVER ACCESSORIES These accessories fasten at the top, around the side tubes.They fit over the sunhood and under the footplate. The lower elastic loops fasten onto the lug below the footplate. Follow removing seat instructions above, in reverse order. strap X lug STORM COVER lug SUN COVER WARNING: Do not leave Storm Cover on stroller in warm conditions. Note: Fasten seat onto frame making sure fabric wraps Check baby’s comfort frequently over and around the top of the side tubes. when using Storm Cover. ✓ CORRECT 7 Care and Maintenance WARNING: This stroller requires regular maintenance by the user. FABRIC CARE AND CLEANING This outdoor fabric should be cleaned regularly. Brush off any excessive dirt and rinse with warm water. Fabric can be removed and washed by hand using a mild natural soap solution in luke warm water (no more than 38˚C / 100˚F). Rinse thoroughly to remove soap. DO NOT use detergents! Allow to air dry. DO NOT tumble dry. TYRES/TIRES & TUBES If a puncture occurs, the inner tube can be repaired with a bicycle repair kit, or replaced. If the tread becomes completely worn the tyre/tire should be replaced. Replacement tyres/tires, inner tubes and repair kits are available from your authorised dealer or most cycle stores. Inflating the tyres/tires: Inflate to a pressure of 15psi. (105 KPa) Do not exceed 20psi (140 KPa). The valves are the same as a bicycle, or car tyre/tire valve. WARNING: Over inflation may damage wheel. WHEEL ALIGNMENT TERRAIN ONLY It may be necessary to periodically adjust wheel alignment if stroller steers to one side. The Terrain stroller has angle struts on the rear axle for this purpose. 1 Loosen all four nuts A, B, C & D holding strut in position. 2 Slightly tighten outside nut on the opposite side to the direction it is steering (eg if steering to left tighten nut D). 3 Test the stroller wheel alignment by pushing it on a smooth flat surface. 4 Re-test the stroller steering after every turn of the nut until the stroller will run in a straight line. 5 When the correct steering is achieved, turn the outside nut on the opposite side so it just touches the side of the tube. 6 Tighten the inside nuts. STROLLER FRAME The main frame is aluminium/aluminum and corrosion resistant. The Urban front assembly and some components are steel and will corrode if exposed to environments such as, salt water, salt spray or beach sand. If stroller is used in these environments, wash steel parts in warm soapy water, dry thoroughly and protect by spraying with light aerosol can oil eg WD40 or CRC. BRAKE The brake cam may require lubrication if it becomes difficult to operate. lubricate this surface brake lever STORAGE Store inside in a dry place. Make sure the stroller is dry before storing. velcro A B C D wrist strap HANDLEBAR GRIP Take care to protect the handlebar grip from abrasion or sharp objects. Contact your authorised dealer or distributor for replacement grips and instructions. A wetsuit glue can be used to repair cuts. 8 Wrist strap can be used to hold stroller together in its fully folded position. Loop wrist strap around rear axle then fasten. Sunhood can be fastened back by applying velcro on sunhood window flap to the velcro on edge of sunhood. WARNING: It may be unsafe to use replacement parts other than those supplied or approved by the manufacturer or distributor. Parts of Stroller Frame Note: Diagram is Urban Single model Handle Adjuster Handlebar Sunhood Support Wire Side Tube Sunhood Joint* Fastener Down Tube Under-Carriage Tube Brake Cog Heel Rest Brake Cam* Sliding Lock* Rear Axle Footplate Quick Release Clip* Brake Lever Rear Wheel *Points to lubricate periodically Sliding Lock* Swivel Knob* Accessory Lug Front Wheel Front Wheel Swivel* (Urban Only) 9 Carrycot Bumper Bar KiddyBoard™ Pump Sleeping Bag Hand Brake Handlebar Extension Travel Bag Evenflo Carseat Clip Universal Carseat Clip Model Sun Cover Accessories Storm Cover Accessories Urban Single Urban Double Urban Triple Terrain Single Terrain Double Breeze ** Several Carseat Clips designed for specific model car seats are available to fit Single, Double and Triple model strollers. (These are not available in all countries, check with your authorised dealer or go to www.mountainbuggy.com). 10 Warranty Conditions This warranty covers: Defects in workmanship and materials for one year from date of purchase. The distributor undertakes to repair or at their option, replace any part, which is found to be defective within warranty period. • Repairs when product has been dismantled, repaired, modified or serviced by other than an authorized agent. • Repairs when stroller has not been used for normal use and in accordance with manufacturer’s instructions. This warranty does not cover: • Pick up, delivery or service calls. • Temporary replacement while stroller is being repaired or assessed. • Damage to tyres/tires, tubes and handlebar grips. • Instruction or assistance with wheel assembly or setup of stroller. • Corrosion or fabric damage, if stroller has been used or stored in extreme environmental conditions. e.g. high humidity, salt spray. • Deterioration due to lack of maintenance and cleaning as specified in manufacturer’s instructions. • Normal wear and tear or damage to product caused by accident, misuse or act of nature. If the product fails within the warranty period: Return it to the Authorized Dealer where purchased from. They will arrange for assessment and appropriate action during normal business hours. If you are unsure where to take stroller contact distributor in your country for instructions. Repairs and replacement parts: If stroller requires repair contact your authorised dealer or distributor, to obtain information and spare parts. If you are in a different country than where you purchased the product, please contact the distributor for the country where you purchased, as extra charges may apply. Please make sure product is clean. Unacceptably dirty products will not be handled. International Distributors Send the Warranty Registration Card to the distributor for the country of purchase. (If there is no distributor please send it to New Zealand.) NEW ZEALAND & HEAD OFFICE Freepost 191-029 (within New Zealand) P. O. Box 38-781, Wellington Mail Centre, New Zealand Ph: (04) 568 1590 or 0800 428 449 Fax: (04) 569 6239 email: enquiries@mountainbuggy.com www.mountainbuggy.com AUSTRALIA Mountain Buggy Australia 223A East Boundary Road East Bentleigh,Victoria 3165, Australia Ph: (03) 9570 2833 Fax: (03) 9570 1362 email: info@mountainbuggy.com.au www.mountainbuggy.com.au U.K. & IRELAND Mountain Buggy (UK) Ltd Mill Farm, Fairmile, Ottery St Mary Devon EX11 1LS, England Ph: ++44 01 404 815 555 or 07000 4 BUGGY (07000 428 449) Fax: ++44 01 404 815 444 email: info@mountainbuggy.co.uk www.mountainbuggy.co.uk EUROPE: One Tree Hill Postbus 4, 3130 AA Vlaardingen, The Netherlands Ph: ++31(0) 182 551895 Fax: ++31(0) 182 551457 email: info@onetreehill.nl www.onetreehill.nl JAPAN: Office U Corporation 2-22-8, Higashi Kawaguchi, Kawaguchi City, Saitama Prefecture, Japan 333-0801 Ph: (048) 294 7211 Mob: (090) 3137 1234 Fax: (048) 297 7207 www.mountainbuggy.com SINGAPORE & HONG KONG: Mountain Buggy Asia P.O. Box 603, 144 Upper Bukit Timah Rd #04-16-17, Beauty World Centre, Singapore 588177 Ph: (09) 416 8617 Fax: (09) 416 8617 Email: mtnbuggy@singnet.com.sg www.mountainbuggy.com USA: Sycamore Kids Inc. 4562 Denrose Ct. Suite 2 Fort Collins, CO 80524 USA Toll Free Phone/Fax: 866 524 8805 email: support@mountainbuggyusa.com www.mountainbuggyusa.com CANADA: Mountain Buggy Canada Inc 4298 Capilano Road, North Vancouver, B.C. V7R 4J7, Canada Toll Free Phone: 1866 MTNBUGGY (1866 686 28449) email: info@mountainbuggy.ca www.mountainbuggy.ca SOUTH AFRICA: Suffolk Trading CC P.O. Box 46911, Glossderry 7702, South Africa Ph: ++27 11 485 3458 Fax: ++27 11 485 5273 email: isacks@iafrica. com www.mountainbuggy.com 11 Warranty Registration Congratulations on purchasing a Mountain Buggy®. To register for your 12 month warranty, please return this registration form to your distributor (see previous page). Please take a few moments to review the additional questions about your purchase. We would appreciate your replies so that we can continue to improve our product. Name: _____________________________________________________________ Address: ___________________________________________________________ ___________________________________________________________________ Phone: ______________________Email: _________________________________ ® This information will remain confidential to Mountain Buggy only. Tick here if you do not wish to receive future marketing material. Model Number (under footplate): _______________________________________ Serial Number (under footplate): _______________________________________ Date of Purchase: ___________________________________________________ Purchased From: ____________________________________________________ Which accessories have you purchased for your Mountain Buggy®? Sleeping Bag Carseat Clip Handlebar Extension KiddyBoard™ Storm Cover Bumper Bar Sun Cover Hand Brake Carrycot Travel Bag Pump How did you find out about Mountain Buggy®? Magazine (Name) ____________ Show/Event (Name) ________________ Internet Friend/Family Other (please explain) _____________________________________________ What comes to mind when you hear the words Mountain Buggy®? ___________________________________________________________________ What activities have you purchased your Mountain Buggy® for? Exercising Farming lifestyle Shopping Hiking Urban use Other (please explain) ________________________ The family member most influential in purchasing a Mountain Buggy® Mother Father Both Parents Grandparents Other (please explain) _____________________________________________ How important were the following factors in your purchase? 1=Very Important 2=Important 3=Not Very Important 4= Not Important Strength of Stroller NZ Made Weight of Stroller Safety Ease of Use General Appearance Ease of Folding Reputation of Brand/Product Accessories Available Off-Road Capability At time of purchase mother was _____________months pregnant, or had a _____________month old child. Additional Comments: _____________________________________________ ___________________________________________________________________ ___________________________________________________________________
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Modify Date : 2005:08:23 09:26:08+12:00 Create Date : 2005:04:01 11:55:54+12:00 Page Count : 11 About : uuid:749b00f1-a240-11d9-88ad-000a95b693e4 Producer : Acrobat Distiller 6.0.1 for Macintosh Creation Date : 2005:04:01 11:55:54+12:00 Mod Date : 2005:08:23 09:26:08+12:00 Metadata Date : 2005:08:23 09:26:08+12:00 Document ID : uuid:749af043-a240-11d9-88ad-000a95b693e4 Format : application/pdf Title : untitledEXIF Metadata provided by EXIF.tools