Moxa WAPN005 MOXA IEEE 802.11a/b/g/n wireless User Manual WAPN005 Users Manual v1
Moxa Inc. MOXA IEEE 802.11a/b/g/n wireless WAPN005 Users Manual v1
Moxa >
Contents
User Manual
Moxa IEEE 802.11a/b/g/n Wireless Module WAPN005 User’s Manual First Edition, April 2014 www.moxa.com/product © 2014 Moxa Inc. All rights reserved. Moxa IEEE 802.11a/b/g/n Wireless Module WAPN005 User’s Manual The software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement. Copyright Notice © 2014 Moxa Inc. All rights reserved. Trademarks The MOXA logo is a registered trademark of Moxa Inc. All other trademarks or registered marks in this manual belong to their respective manufacturers. Disclaimer Information in this document is subject to change without notice and does not represent a commitment on the part of Moxa. Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the products and/or the programs described in this manual, at any time. Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for its use, or for any infringements on the rights of third parties that may result from its use. This product might include unintentional technical or typographical errors. Changes are periodically made to the information herein to correct such errors, and these changes are incorporated into new editions of the publication. Technical Support Contact Information www.moxa.com/support Moxa Americas Moxa China (Shanghai office) Toll-free: 1-888-669-2872 Toll-free: 800-820-5036 Tel: +1-714-528-6777 Tel: +86-21-5258-9955 Fax: +1-714-528-6778 Fax: +86-21-5258-5505 Moxa Europe Moxa Asia-Pacific Tel: +49-89-3 70 03 99-0 Tel: +886-2-8919-1230 Fax: +49-89-3 70 03 99-99 Fax: +886-2-8919-1231 Moxa India Tel: +91-80-4172-9088 Fax: +91-80-4132-1045 Table of Contents 1. Introduction...................................................................................................................................... Overview ........................................................................................................................................... Features ............................................................................................................................................ Specifications ..................................................................................................................................... 1-1 1-2 1-2 1-2 2. Getting Started................................................................................................................................. Module Layout.................................................................................................................................... Hardware Block Diagram ..................................................................................................................... Connector Location ............................................................................................................................. Board-to-board Bus Connector PIN Assignments..................................................................................... Hardware Installation .......................................................................................................................... Software Installation ........................................................................................................................... 2-1 2-2 2-3 2-3 2-4 2-5 2-5 A. Regulatory Statement Approval ........................................................................................................ A-1 1 1. Introduction This chapter briefly introduces the overview, features and the specifications of the WAPN005 wireless module. The following topics are covered in this chapter: Overview Features Specifications WAPN005 User's Manual Introduction Overview Moxa WAPN005 module is designed to provide wireless communication for all wireless device based systems. It communicates via the standard 802.11a/b/g/n protocols, and uses the AR9344 wireless chipset from Atheros. Features Dynamic frequency selection (DFS) in required 5-GHz bands All-CMOS MIMO solution interoperable with IEEE 802.11a/b/g/n WLANs No external VCOs or SAW filters needed 2.4/5 GHz WLAN MAC/BB processing BPSK, QPSK, 16 QAM, 64 QAM, DBPSK,DQPSK, and CCK modulation schemes 802.11e-compatible bursting Wireless multimedia enhancements quality of service supported (QoS) 802.11e-compatible bursting WEP, TKIP, and AES hardware encryption IEEE 1149.1 standard test access port and boundary scan architecture supported Case temperature 85°C Specifications Features WAPN005 Specifications Chipset Atheros AR9344 Baseband Processor ·DSSS with DBPSK, DQPSK, CCK (BBP) ·OFDM with BPSK, QPSK, 16QAM, 64QAM ·802.11b: CCK @ 11/5.5 Mbps, DQPSK @ 2 Mbps,DBPSK @ 11 Mbps ·802.11a/g: 64QAM @ 54/48 Mbps, 16QAM @ 36/24 Mbps, QPSK @ 18/12 Mbps, BPSK @ 9/6 Mbps ·802.11n: 64QAM @ 300 Mbps to BPSK @ 6.5 Mbps (multiple rates supported) Security Engine WEP64,WEP128, WEP256, AES-CCM, TKIP ,WPS Bus Interface Moxa proprietary interface Connector Board-to-board 2 x 40 pins header Power Requirement 3.3V +/-10% Dimensions 60 x 60 x 12 mm (2.36 x 2.36 x 0.47 in) Weight 15 g Operating Temperature -40 to 75℃ Storage Temperature: -40 to 85℃ Operates in 2.4 and 5 US: GHz frequency bands. 2.412 to 2.462 GHz (11 channels) 5.180 to 5.320 GHz (8 channels) 5.500 to 5.700 GHz (8 channels - excludes 5.600 to 5.640 GHz) 5.745 to 5.825 GHz (5 channels) EU: 2.412 to 2.472 GHz (13 channels) 5.180 to 5.320 GHz (8 channels) 5.500 to 5.700 GHz (11 channels) JP: 2.412 to 2.484 GHz (14 channels, DSSS) 5.180 to 5.320 GHz (8 channels) 5.500 to 5.700 GHz (11 channels) 1-2 WAPN005 User's Manual Introduction 1-3 2 2. Getting Started This chapter describes the hardware introduction, installation, and software installation. The following topics are covered in this chapter: Module Layout Hardware Block Diagram Connector Location Board-to-board Bus Connector PIN Assignments Hardware Installation Software Installation WAPN005 User's Manual Getting Started Hardware Block Diagram Refer to the following figure the hardware block diagram of the WAPN005. Connector Location Refer to the following figures for the connector location of the WAPN005 module. 2-2 WAPN005 User's Manual Getting Started Board-to-board Bus Connector PIN Assignments Refer to the following figures and table for the PIN assignment of the WAPN005 module connector. Function Connect to Pin Pin Function Connect to 3.3v 3.3v GND GND 3.3v 3.3v GND GND 3.3v 3.3v ERXD3 PHY RGMII 3.3v 3.3v ERXD2 PHY RGMII 3.3v 3.3v 10 ERXD1 PHY RGMII 3.3v 3.3v 11 12 ERXD0 PHY RGMII 3.3v 3.3v 13 14 GND GND GPIO 16 I2C_SCLK 15 16 GND GND GPIO 17 I2C_DATA 17 18 ETX_CLK ETX_CLK GND GND 19 20 GND GND GPIO 21 POWER 2 21 22 GND GND GPIO 1 JP1 Debug 23 24 ETX_EN ETX_EN GND GND 25 26 GND GND GPIO 4 S17_INT 27 28 GND GND GND GND 29 30 ETXD3 PHY RGMII GPIO 0 I2C_INT0 31 32 ETXD2 PHY RGMII GND GND 33 34 ETXD1 PHY RGMII GPIO 3 UR_DSR 35 36 ETXD0 PHY RGMII GPIO 9 UR_SIN 37 38 GND GND GPIO 10 UR_SOUT 39 40 GND GND GPIO 13 MDC 41 42 ERX_CLK ERX_CLK GPIO 14 MDIO 43 44 GND GND GPIO 20 POWER 1 45 46 GND GND GND GND 47 48 ERX_EN ERX_EN GPIO 22 POWER 3 49 50 GND GND GND GND 51 52 GND GND 2-4 WAPN005 User's Manual Getting Started GPIO 2 UR_DTR 53 54 EMDC GIGA PHY GND GND 55 56 EMDIO GIGA PHY GPIO 11 Reset 57 58 GND GND GND GND 59 60 GND GND GPIO 12 LAN 10/100 61 62 TXP0 10/100 LAN GND GND 63 64 TXN0 10/100 LAN GPIO 15 Reserved 65 66 GND GND GND GND 67 68 RXP0 10/100 LAN SYS_RST_L GIGA PHY Reset 69 70 RXN0 10/100 LAN AVDD18 Fast Ethernet bios 71 72 GND GND AVDD18 Fast Ethernet bios 73 74 GND GND AVDD18 Fast Ethernet bios 75 76 USB_DM USB port GND GND 77 78 USB_DP USB port GND GND 79 80 GND GND Hardware Installation Follow these steps to install the hardware components. 1. Attach the WLAN antenna to the connector J1. 2. Attach the second WLAN antenna to the connector J2. 3. Connect the WAPN005 module on the system board with the board-to-board connector and gently press the board onto the stack. The board should slide into the matching bus connectors. Do not attempt to force the board, as the pins may be distorted or broken. 4. Use the screws to fasten the WAPN005 module. 5. If you require the power board, install it above the WAPN005 module. 6. Fasten all components on the necessary chassis. Software Installation Follow these steps to install the software. 1. Power on the system board. 2. Connect system board and PC with an Ethernet cable. 3. Open a browser and type: 192.168.127.253 to open the system login webpage. 4. Login the webpage with default password: root to verify all of the hardware components have been installed properly. 2-5 A Regulatory Statement Approval Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices) any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: This module is restricted to mobile configuration. To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter CAUTION Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: "Contains FCC ID: SLE-WAPN005 ” WAPN005 User's Manual Regulatory Statement Approval RF Exposure Warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Information for the OEMs and Integrators The following statement must be included with all versions of this document supplied to an OEM or integrator, but should not be distributed to the end user. 1) This device is intended for OEM integrators only. 2) Please see the full Grant of Equipment document for other restrictions. This radio transmitter FCCID: SLE-WAPN005 has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antenna List No. Manufacturer Part No. Peak Gain KINSUN ANT-WDB-0-2-BK (main/A) (aux/B) 2.9dBi in 2.4 GHz 2.3dBi in 5 GHz KINSUN ANT-WDB-ANM-0502 (main/A) (aux/B) 4.62dBi in 2.4 GHz 1.41dBi in 5 GHz Note This is a specific product that requires professional installation and configuration, must be performed by trained technical engineers to install the antenna. Contact Moxa for more information. A-2
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Author : Administrator Create Date : 2014:04:23 20:08:23+08:00 Modify Date : 2015:03:13 16:44:43+08:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2015:03:13 16:44:43+08:00 Format : application/pdf Title : Microsoft Word - WAPN005_Users_Manual_v1.doc Creator : Administrator Producer : Acrobat Distiller 9.0.0 (Windows) Document ID : uuid:07e641a0-b83f-42f9-8a08-4462cadc49bd Instance ID : uuid:f9de2554-1774-4633-91f9-ea0e67901f27 Page Count : 12EXIF Metadata provided by EXIF.tools