Moxa WAPN005L MOXA IEEE 802.11a/b/g/n Wireless User Manual WAPN005 Users Manual v1

Moxa Inc. MOXA IEEE 802.11a/b/g/n Wireless WAPN005 Users Manual v1

User manual

Download: Moxa WAPN005L MOXA IEEE 802.11a/b/g/n Wireless User Manual WAPN005 Users Manual v1
Mirror Download [FCC.gov]Moxa WAPN005L MOXA IEEE 802.11a/b/g/n Wireless User Manual WAPN005 Users Manual v1
Document ID2244373
Application IDmyiDGe36EwmBmaUEM8htzA==
Document DescriptionUser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize43.22kB (540221 bits)
Date Submitted2014-04-17 00:00:00
Date Available2014-04-18 00:00:00
Creation Date2014-04-08 15:03:58
Producing SoftwareAcrobat Distiller 9.0.0 (Windows)
Document Lastmod2014-04-08 15:03:58
Document TitleMicrosoft Word - WAPN005_Users_Manual_v1.doc
Document CreatorPScript5.dll Version 5.2.2
Document Author: Administrator

Moxa IEEE 802.11a/b/g/n Wireless
Module WAPN005 User’s Manual
First Edition, April 2014
www.moxa.com/product
© 2014 Moxa Inc. All rights reserved.
Moxa IEEE 802.11a/b/g/n Wireless
Module WAPN005 User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in accordance with
the terms of that agreement.
Copyright Notice
© 2014 Moxa Inc. All rights reserved.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited
to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the
products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for
its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas
Moxa China (Shanghai office)
Toll-free: 1-888-669-2872
Toll-free: 800-820-5036
Tel:
+1-714-528-6777
Tel:
+86-21-5258-9955
Fax:
+1-714-528-6778
Fax:
+86-21-5258-5505
Moxa Europe
Moxa Asia-Pacific
Tel:
+49-89-3 70 03 99-0
Tel:
+886-2-8919-1230
Fax:
+49-89-3 70 03 99-99
Fax:
+886-2-8919-1231
Moxa India
Tel:
+91-80-4172-9088
Fax:
+91-80-4132-1045
Table of Contents
1.
Introduction......................................................................................................................................
Overview ...........................................................................................................................................
Features ............................................................................................................................................
Specifications .....................................................................................................................................
1-1
1-2
1-2
1-2
2.
Getting Started.................................................................................................................................
Module Layout....................................................................................................................................
Hardware Block Diagram .....................................................................................................................
Connector Location .............................................................................................................................
Board-to-board Bus Connector PIN Assignments.....................................................................................
Hardware Installation ..........................................................................................................................
Software Installation ...........................................................................................................................
2-1
2-2
2-3
2-3
2-4
2-5
2-5
A.
Regulatory Statement Approval ........................................................................................................
A-1
1
1.
Introduction
This chapter briefly introduces the overview, features and the specifications of the WAPN005 wireless module.
The following topics are covered in this chapter:
 Overview
 Features
 Specifications
WAPN005 User's Manual
Introduction
Overview
Moxa WAPN005 module is designed to provide wireless communication for all wireless device based systems.
It communicates via the standard 802.11a/b/g/n protocols, and uses the AR9344 wireless chipset from
Atheros.
Features

Dynamic frequency selection (DFS) in required 5-GHz bands

All-CMOS MIMO solution interoperable with IEEE 802.11a/b/g/n WLANs

No external VCOs or SAW filters needed

2.4/5 GHz WLAN MAC/BB processing

BPSK, QPSK, 16 QAM, 64 QAM, DBPSK,DQPSK, and CCK modulation schemes

802.11e-compatible bursting

Wireless multimedia enhancements quality of service supported (QoS)

802.11e-compatible bursting

WEP, TKIP, and AES hardware encryption

IEEE 1149.1 standard test access port and boundary scan architecture supported

Case temperature 85°C
Specifications
Features
WAPN005 Specifications
Chipset
Atheros AR9344
Baseband Processor
·DSSS with DBPSK, DQPSK, CCK
(BBP)
·OFDM with BPSK, QPSK, 16QAM, 64QAM
·802.11b: CCK @ 11/5.5 Mbps, DQPSK @ 2 Mbps,DBPSK @ 11 Mbps
·802.11a/g: 64QAM @ 54/48 Mbps, 16QAM @ 36/24 Mbps, QPSK @ 18/12 Mbps,
BPSK @ 9/6 Mbps
·802.11n: 64QAM @ 300 Mbps to BPSK @ 6.5 Mbps (multiple rates supported)
Security Engine
WEP64,WEP128, WEP256, AES-CCM, TKIP ,WPS
Bus Interface
Moxa proprietary interface
Connector
Board-to-board 2 x 40 pins header
Power Requirement
3.3V +/-10%
Dimensions
60 x 60 x 12 mm (2.36 x 2.36 x 0.47 in)
Weight
15 g
Operating Temperature
-40 to 75℃
Storage Temperature:
-40 to 85℃
Operates in 2.4 and 5
US:
GHz frequency bands.
2.412 to 2.462 GHz (11 channels)
5.180 to 5.320 GHz (8 channels)
5.500 to 5.700 GHz (8 channels - excludes 5.600 to 5.640 GHz)
5.745 to 5.825 GHz (5 channels)
EU:
2.412 to 2.472 GHz (13 channels)
5.180 to 5.320 GHz (8 channels)
5.500 to 5.700 GHz (11 channels)
JP:
2.412 to 2.484 GHz (14 channels, DSSS)
5.180 to 5.320 GHz (8 channels)
5.500 to 5.700 GHz (11 channels)
1-2
WAPN005 User's Manual
Introduction
1-3
2
2.
Getting Started
This chapter describes the hardware introduction, installation, and software installation.
The following topics are covered in this chapter:
 Module Layout
 Hardware Block Diagram
 Connector Location
 Board-to-board Bus Connector PIN Assignments
 Hardware Installation
 Software Installation
WAPN005 User's Manual
Getting Started
Module Layout
Refer to the following figure for the module layout of the WAPN005.
2-2
WAPN005 User's Manual
Getting Started
Hardware Block Diagram
Refer to the following figure the hardware block diagram of the WAPN005.
Connector Location
Refer to the following figures for the connector location of the WAPN005 module.
Front
Rear
2-3
WAPN005 User's Manual
Getting Started
Board-to-board Bus Connector PIN
Assignments
Refer to the following figures and table for the PIN assignment of the WAPN005 module connector.
Function
Connect to
Pin
Pin
Function
Connect to
3.3v
3.3v
GND
GND
3.3v
3.3v
GND
GND
3.3v
3.3v
ERXD3
PHY RGMII
3.3v
3.3v
ERXD2
PHY RGMII
3.3v
3.3v
10
ERXD1
PHY RGMII
3.3v
3.3v
11
12
ERXD0
PHY RGMII
3.3v
3.3v
13
14
GND
GND
GPIO 16
I2C_SCLK
15
16
GND
GND
GPIO 17
I2C_DATA
17
18
ETX_CLK
ETX_CLK
GND
GND
19
20
GND
GND
GPIO 21
POWER 2
21
22
GND
GND
GPIO 1
JP1 Debug
23
24
ETX_EN
ETX_EN
GND
GND
25
26
GND
GND
GPIO 4
S17_INT
27
28
GND
GND
GND
GND
29
30
ETXD3
PHY RGMII
GPIO 0
I2C_INT0
31
32
ETXD2
PHY RGMII
GND
GND
33
34
ETXD1
PHY RGMII
GPIO 3
UR_DSR
35
36
ETXD0
PHY RGMII
GPIO 9
UR_SIN
37
38
GND
GND
GPIO 10
UR_SOUT
39
40
GND
GND
GPIO 13
MDC
41
42
ERX_CLK
ERX_CLK
GPIO 14
MDIO
43
44
GND
GND
GPIO 20
POWER 1
45
46
GND
GND
GND
GND
47
48
ERX_EN
ERX_EN
GPIO 22
POWER 3
49
50
GND
GND
GND
GND
51
52
GND
GND
2-4
WAPN005 User's Manual
Getting Started
GPIO 2
UR_DTR
53
54
EMDC
GIGA PHY
GND
GND
55
56
EMDIO
GIGA PHY
GPIO 11
Reset
57
58
GND
GND
GND
GND
59
60
GND
GND
GPIO 12
LAN 10/100
61
62
TXP0
10/100 LAN
GND
GND
63
64
TXN0
10/100 LAN
GPIO 15
Reserved
65
66
GND
GND
GND
GND
67
68
RXP0
10/100 LAN
SYS_RST_L
GIGA PHY Reset
69
70
RXN0
10/100 LAN
AVDD18
Fast Ethernet bios
71
72
GND
GND
AVDD18
Fast Ethernet bios
73
74
GND
GND
AVDD18
Fast Ethernet bios
75
76
USB_DM
USB port
GND
GND
77
78
USB_DP
USB port
GND
GND
79
80
GND
GND
Hardware Installation
Follow these steps to install the hardware components.
1. Attach the WLAN antenna to the connector J1.
2. Attach the second WLAN antenna to the connector J2.
3. Connect the WAPN005 module on the system board with the board-to-board connector and gently press the
board onto the stack. The board should slide into the matching bus connectors. Do not attempt to force the
board, as the pins may be distorted or broken.
4. Use the screws to fasten the WAPN005 module.
5. If you require the power board, install it above the WAPN005 module.
6. Fasten all components on the necessary chassis.
Software Installation
Follow these steps to install the software.
1. Power on the system board.
2. Connect system board and PC with an Ethernet cable.
3. Open a browser and type: 192.168.127.253 to open the system login webpage.
4. Login the webpage with default password: root to verify all of the hardware components have been
installed properly.
2-5
A
Regulatory Statement Approval
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
To assure continued compliance, (example - use only shielded interface cables when connecting to computer or
peripheral devices) any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
IMPORTANT NOTE:
This module is restricted to mobile configuration. To comply with FCC RF exposure compliance requirements,
the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from
all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This
transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter
CAUTION
Any changes or modifications not expressly approved by the grantee of this device could void the user's
authority to operate the equipment.
This device is operation in 5.15 – 5.25GHz frequency range, then restricted in indoor use only.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20cm
may be maintained between the antenna and users. The final end product must be labeled in a visible area with
the following: "Contains FCC ID: SLE-WAPN005 ”
WAPN005 User's Manual
Regulatory Statement Approval
RF Exposure Warning
This equipment must be installed and operated in accordance with provided instructions and the antenna(s)
used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons
and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and
installers must be provide with antenna installation instructions and transmitter operating conditions for
satisfying RF exposure compliance.
Information for the OEMs and Integrators
The following statement must be included with all versions of this document supplied to an
OEM or integrator, but should not be distributed to the end user.
1) This device is intended for OEM integrators only.
2) Please see the full Grant of Equipment document for other restrictions.
This radio transmitter FCCID: SLE-WAPN005 has been approved by FCC to operate with the antenna types
listed below with the maximum permissible gain and required antenna impedance for each antenna type
indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for
that type, are strictly prohibited for use with this device.
Antenna List
No.
Manufacturer
Part No.
Peak Gain
KINSUN
ANT-WDB-0-2-BK (main/A) (aux/B)
2.9dBi in 2.4 GHz
2.3dBi in 5 GHz
KINSUN
ANT-WDB-ANM-0502 (main/A) (aux/B)
4.62dBi in 2.4 GHz
1.41dBi in 5 GHz
Note
This is a specific product that requires professional installation and configuration, must be performed by trained
technical engineers to install the antenna. Contact Moxa for more information.
Hosted Information
The WAPN005 has received Limited Module Approval (LMA) from FCC. This is because the WAPN005 does not have
own RF shielding, this module is only installed at the following host product, isn’t installed to the other host products.
(The host product manufacture and model name is MOXA/ AWK‐1131A)
When module installed on other host equipment, then it must be re‐evaluated via asking FCC or TCB, such that full
compliance of the end product is always ensured.
Please note that the module must state that the module is only approved for use when installed in devices as stated in
the filing under FCC ID: SLE‐WAPN005.
A-2

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Administrator
Create Date                     : 2014:04:08 15:03:58+08:00
Modify Date                     : 2014:04:08 15:03:58+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - WAPN005_Users_Manual_v1.doc
Creator                         : Administrator
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:4c361982-c7cc-4739-96db-1eb2c3f75bfd
Instance ID                     : uuid:437de9fb-a3e4-4b78-8113-6fcfaf53927b
Page Count                      : 13
EXIF Metadata provided by EXIF.tools
FCC ID Filing: SLE-WAPN005L

Navigation menu