Murata Electronics North America 934 Frequency Hopping RF Modem User Manual Rev 091907

Download:
Mirror Download [FCC.gov]
Document ID	845327
Application ID	00wCqM78jPGkPBj1HQe+hA==
Document Description	User Manual Rev 091907
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	6.59kB (82410 bits)
Date Submitted	2007-09-19 00:00:00
Date Available	2007-08-24 00:00:00
Creation Date	2007-09-19 11:30:13
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2007-09-19 11:30:13
Document Title	Microsoft Word - WIT934 Integration Manual Rev B.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	Doug Noble

WIT934
WIT934
900MHz Spread Spectrum Wireless Industrial
Transceiver
Preliminary
Integration Guide
3079 Premiere Pkwy Ste 140
Norcross, Georgia 30097
www.cirronet.com
+1 (678) 684-2000
© 2000- 2007 Cirronet™ Inc
M-0910-0000 Rev -
WIT934
Important Regulatory Information
Cirronet Product FCC ID: HSW-934
IC 4492A-934
Note: This unit has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at their expense.
FCC s MPE Requirements
Information to user/installer regarding FCC s Maximum Permissible Exposure (MPE) limits.
Notice to WIT934 users/installers using the following fixed antenna:
2dBi Cirronet OMNI092
The field strength radiated by this antenna, when connected to a transmitting WIT934, does not exceed
FCC mandated RF exposure limits.
For Portable (body worn) use this unit is below the FCC Maximum Permissible Exposure limits for
distances less than 2.5 cm for the ‘General Population’
When used as an Access Point or Mobile, with a higher transmitter time, this unit is below the FCC
Maximum Permissible Exposure limits for 20 cm for the ‘General Population’
The antenna used for this transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Changes or modifications not expressly approved by the party responsible may void the users ability to
operate the equipment.
© 2000- 2007 Cirronet™ Inc
M-0910-0000 Rev -
WIT934
1.1 Technical Specifications
1.1.1 Ordering Information
WIT934M OEM Module, Serial connector pins down - Standard
1.1.2 Power Specifications
Vcc Input Range:
Operating Temperature Range:
3.3v to 10.0v (500mW requires 5.0Vcc)
-40°C to +70°C
Current Consumption (@5V, max transmit power & 115.2Kbps I/O)
Mode
Standby
Typical Average
Peak (Tx)
Remote
43mA
<100mA
600mA
Base Station
N/A
125mA
600mA
1.1.3 RF Specifications
FCC Certification
Rated RF Power
Line-of-site Range
Frequency Range
Number of Channels
Receiver Sensitivity
Channel Data Rate
IF Adjacent Channel Rejection
Part 15.247, no license required
+24 dBm
20+ miles with omni antenna
902 to 927 MHz
37
-103dBm for 10-5 BER
172.8Kbps
>55dB
1.1.4 Mechanical Specifications
Weight
Dimensions (including shield)
35g
80.2 x 46.5 x 8.6mm
(refer to section 7.6 for mechanical drawing)
RF Connector:
WIT
Mating
Huber/Suhner: 85 MMCX 50-0-1
Huber/Suhner: 11 MMCX-50-2-3 (straight)
Huber/Suhner: 16 MMCX-50-2-2 (rt. angle)
Data/Power Connector:
WIT
Mating
© 2000- 2007 Cirronet™ Inc
Samtec: DIS5-108-51-L-D
Samtec: CLP-108-02-G-D (PCB mount)
Samtec: FFSD-08 (IDC cable)
M-0910-0000 Rev -
WIT934
When connecting to the WIT934, make sure that all of the inputs (TXD, CFG, RTS and
SLEEP) are terminated for proper operation.
1.2 Approved Antennas
The WIT934 is designed to ensure that no antenna other than the one fitted shall be used
with the device. The table below lists the antennas which can be purchased directly from
Cirronet.
Description
2dB Omnidirectional
Gain
2dB
Part Number
OMNI092
Coupling
Male Rev TNC
1.3 Use of the WIT934 in Portable or Remote Applications
When using the WIT934 in a portable or body worn application the unit is operated as a
‘remote’ to the ‘base’ (or Access Point) and has a duty cycle of 7.4%. This meets the
requirements of the FCC Maximum Permissible Exposure limits for distances less than
2.5 cm for the ‘General Population’
1.4 Use of the WIT934 in Access Point or Base Applications
When using the WIT934 in an Access Point or base application the unit is operated at a
higher duty cycle of 21%. The unit can not be body worn and the antenna must be 20 cm
away from ‘General Population’ Operation is best in a high location to access all the
remotes or portable units. Operating as an Access Point or base the WIT934 meets the
requirements of a Mobile device per the FCC Maximum Permissible Exposure limits for
distances of 20 cm for the ‘General Population’
© 2000- 2007 Cirronet™ Inc
M-0910-0000 Rev -

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2007:09:19 11:30:13-07:00
Create Date                     : 2007:09:19 11:30:13-07:00
Format                          : application/pdf
Title                           : Microsoft Word - WIT934 Integration Manual Rev B.doc
Creator                         : Doug Noble
Document ID                     : uuid:d04fc0cd-90b8-4916-b135-c31b6621f2c1
Instance ID                     : uuid:62d575ab-2d71-4611-a26a-5f9eaf150ff0
Page Count                      : 4
Author                          : Doug Noble

EXIF Metadata provided by EXIF.tools