Murata Electronics North America Z2400HP ZMN2400HP ZigBee Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	849800
Application ID	RMCEdYZxJUlspB5mMqnZMw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	Yes
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	4.34kB (54281 bits)
Date Submitted	2007-10-01 00:00:00
Date Available	2007-10-01 00:00:00
Creation Date	2007-10-01 13:47:31
Producing Software	Acrobat Distiller 8.1.0 (Windows)
Document Lastmod	2007-10-01 11:09:40
Document Title	Microsoft Word - ZN2400 MANUAL FCC Design Documentation Rev6.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	Lou Feudi

ZMN2400 Series
Radio Module
ZMN2400HP, High Power
Manual
Preliminary
Cirronet, Inc.
CIRRONET, INC. ©
"ZMN2400 Design Documentation ", AP, 10/1/07. 1 of 5
Important Regulatory Information
Cirronet Zigbee High Power - FCC ID: HSW-Z2400HP
IC: 4492A-Z2400HP
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS. (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE,
AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE
THAT MAY CAUSE UNDESIRED OPERATION.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC User Information
“NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.”
Warning: Changes or modifications to this device not expressly approved by Cirronet Inc.
could void the user’s authority to operate the equipment.
RF Exposure
In accordance with FCC requirements of human exposure to radiofrequency fields, the radiating
element shall be installed such that a minimum separation distance of 20cm
shall be maintained from the user and/or general population.
The transmitter module may not be co-located with any other transmitter or antenna.
Industry Canada
This Class B digital apparatus meets all requirements of the Canadian Interference
Causing Equipment Regulations. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Cet appareillage numérique de la classe B répond à toutes les exigences de
l'interférence canadienne causant des règlements d'équipement. L'opération est sujette
aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l'interférence nocive,
et (2) ce dispositif doit accepter n'importe quelle interférence reçue, y compris
l'interférence qui peut causer l'opération peu désirée.
CIRRONET, INC. ©
"ZMN2400 Design Documentation ", AP, 10/1/07. 2 of 5
Hardware Specifications
Radio Specifications
Operating Band
Radio Type
Channel Bit Rate
Channel Chipping Rate
Modulation
Certification Type
RF power
Receiver Sensitivity
Link Margin
Adjacent Ch. Rejection
Spurious Output
2400-2475 MHz
Direct Sequence (DTS), IEEE 802.15.4 PHY layer
250 Kbps
2 Mcps
MSK with Raised Cosine Filtering
DTS device per FCC 15.247 and ETS 300-328
+18 dBm typical, +15 dBm minimum
-98 dBm typical, -95 dBm minimum
110 dB (approximately 3 Km Line of Sight propagation)
>39 dB with jammer @ 5 MHz offset
Per FCC 15.247 and ETS 300-328
General
Input Voltage
Current Consumption
Operating Temp Range
Humidity
RF Connector
Host Connector
Power Connector
5.5 volts minimum, 6 volts nominal, 15 volts maximum
70 mA typical operating, 180 mA peak (transmit)
-40 C to + 70 C
95% Non-condensing
Reverse SMA
Male DB-9 (Amp 747840-3)
CUI Stack PJ-002A
Theory of Operation
The Cirronet ZMN2400 Series radio modules utilizes the IEEE 802.15.4 standard ZigBee Physical layer
hardware for wireless low data rate monitoring and control applications. The application of the ZMN2400
Series in a wireless network for data collection in industrial monitoring and control.
Block Diagram in Figure 1
The ZMN2400 Series radio modules consist of an RF transceiver and a microprocessor in one chip.
The RF transceiver receives data and commands from the microprocessor as well as the clock required by
the RF transceiver.
The Block diagrams in Figure 1 shows both the ZMN2400 (Low Power) and the ZMN2400HP (High Power).
They are the same with the exception of T/R switches and a PA (Power Amp) and a LNA (Low Noise Amp) in
the high power version. The output power is +16 dBm for the high power and 0 dBm for the low power
ZigBee Transceivers.
CIRRONET, INC. ©
"ZMN2400 Design Documentation ", AP, 10/1/07. 3 of 5
PA
ZigBee RF
Transceiver
and Processor
S PD
SPD
LPF
BPF
LNA
ZigBee ZMN2400HP
High Power Module
Figure 1
CIRRONET, INC. ©
"ZMN2400 Design Documentation ", AP, 10/1/07. 4 of 5
ZMN2400 Frequency Selection
The ZMN2400 is not frequency agile during run-time, but it can select an unoccupied portion of the spectrum
at startup.
The ZMN-2400 series uses a set of channels as defined by the IEEE 802.15.4 / ZigBee standards which
span a range from 2405 to 2480 MHz with 5 MHz spacing between channels:
Center Frequency (MHz)
2405
2410
2415
2420
2425 (default)
2430
2435
2440
2445
2450
2455
2460
2465
2470
2475
2480 NOT USED
Nominal Occupied BW
2402.5-2407.5
2407.5-2412.5
2412.5-2417.5
2417.5-2422.5
2422.5-2427.5
2427.5-2432.5
2432.5-2437.5
2437.5-2442.5
2442.5-2447.5
2447.5-2452.5
2452.5-2457.5
2457.5-2462.5
2462.5-2467.5
2467.5-2472.5
2472.5-2477.5
2477.5-2482.5
ZigBee Channel Designator
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
The channel mask is the name used to describe the list of frequency channels that a ZMN-2400 can use.
The default channel mask for client radios allows them to operate on any frequency from 2405 to 2475
(channel 2480 is reserved for manufacturing test purposes and therefore not included).
CIRRONET, INC. ©
"ZMN2400 Design Documentation ", AP, 10/1/07. 5 of 5

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-702
Format                          : application/pdf
Creator                         : Lou Feudi
Title                           : Microsoft Word - ZN2400 MANUAL FCC Design Documentation Rev6.doc
Create Date                     : 2007:10:01 13:47:31-04:00
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2007:10:01 11:09:40-07:00
Metadata Date                   : 2007:10:01 11:09:40-07:00
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Document ID                     : uuid:4d1672bc-0e3b-465f-abe6-58548ee5050c
Instance ID                     : uuid:614e2c41-0b45-4b29-b5b2-907b27d70212
Page Count                      : 5
Author                          : Lou Feudi

EXIF Metadata provided by EXIF.tools