Murata LB1CL Communication Module User Manual

Murata Manufacturing Co., Ltd. Communication Module

Contents

User Manual

1Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 08 January 2016LBEQ6ZZ1CL Installation Manual for FCCFCC ID of this product is as follows.FCC ID: VPYLB1CLContents1. PIN Layout2. Supply Voltage3. Power Levels4. NoticePlease make sure that your product has been evaluated andconfirmed from the aspect of the fitness for the specifications and thisdocumentation of our product.
2Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 08 January 20161. PIN Layout<Top View><Bottom View>D1231CLxxx123456789ABCDEModel:LBEQ6ZZ1CLFCC ID:VPYLB1CLIC:772C-LB1CLMNo. PIN NAME No. PIN NAME No. PIN NAME1 GND 21 PCM_SYNC 41 NC2 GND 22 GND 42 GND3 GND 23 SD_CLK 43 GPIO24 NC 24 SD_CMD 44 GPIO35 NC 25 SD_D0 45 GND6 NC 26 SD_D1 46 GND7 GPIO0 27 SD_D2 47 GND8 TCK 28 SD_D3 48 BT_ANT9 TMS 29 GND 49 GND10 TDI 30 GND 50 GND11 TDO 31 VBAT 51 GND12 GPIO1 32 GND 52 GND13 GND 33 PDn 53 GND14 NC 34 UART_TX 54 GND15 GND 35 UART_RX 55 GND16 VIO 36 UART_CTS 56 GND17 GND 37 UART_RTS 57 WLAN_ANT18 PCM_IN 38 NC 58 GND19 PCM_OUT 39 GND20 PCM_CLK 40 NC
3Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 08 January 20162. Supply Voltagemin. typ. max. unitOperating Temperature -40 25 85 deg.CSupply Voltage VBAT 3.0 3.3 3.6 V
4Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 08 January 20163. Power LevelsMode Setting Power[dBm]IEEE 802.11b 18IEEE 802.11g 14IEEE 802.11n 14Mode Setting Power[dBm]BT 7BLE 7Mode Setting Power[dBm]IEEE 802.11a 14IEEE 802.11n (HT20) 14IEEE 802.11n (HT40) 13IEEE 802.11ac (HT20) 8IEEE 802.11ac (HT20 8IEEE 802.11ac (VHT80) 8<Wi-Fi 2.4GHz><Wi-Fi 5GHz><Bluetooth>
5Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 08 January 20164. NoticeFederal Communication Commission Interference StatementThis device complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) This device may not cause harmful interference, and (2) this device must accept anyinterference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.- Consult the dealer or an experienced radio/TV technician for help.FCC Caution: Any changes or modifications not expressly approved by the party responsible forcompliance could void the user's authority to operate this equipment.This transmitter must not be co-located or operating in conjunction with any other antenna ortransmitter.
6Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 08 January 20164. NoticeRadiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolledenvironment. This equipment should be installed and operated with minimum distance 20cmbetween the radiator & your body.
7Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 08 January 20164. NoticeThis device is intended only for OEM integrators under the following conditions:1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and2) The transmitter module may not be co-located with any other transmitter or antenna.3) The use of an antenna with gain less than 2.07 dBi (for 2.4GHz) and 2.43 dBi (for 5GHz)As long as 2 conditions above are met, further transmitter test will not be required. However, the OEMintegrator is still responsible for testing their end-product for any additional compliance requirementsrequired with this module installedIMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptopconfigurations or co-location with another transmitter), then the FCC authorization is no longerconsidered valid and the FCC ID can not be used on the final product. In these circumstances, the OEMintegrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining aseparate FCC authorization.End Product LabelingThis transmitter module is authorized only for use in device where the antenna may be installed such that20 cm may be maintained between the antenna and users. The final end product must be labeled in avisible area with the following: “Contains FCC ID:VPYLB1CL”. The grantee‘s FCC ID can be used onlywhen all FCC compliance requirements are met.Manual Information To the End UserThe OEM integrator has to be aware not to provide information to the end user regarding how to install orremove this RF module in the user’s manual of the end product which integrates this module.The end user manual shall include all required regulatory information/warning as show in this manual.

Navigation menu