Music Tribe Commercial MY Sdn Bhd PPA500BT Portable PA System User Manual Manual
MUSIC Group Services PH Corp Portable PA System Manual
Contents
- 1. Manual
- 2. Addendum
Manual
Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock. Use only high-quality professional speaker cables with ¼" TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel. This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure - voltage that may be sufficient to constitute a risk of shock This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. Please read the manual. Caution To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user serviceable parts inside. Refer servicing to qualified personnel. Caution To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture. The apparatus shall not be exposed to dripping or splashing liquids and no objects filled with liquids, such as vases, shall be placed on the apparatus. Caution These service instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions. Repairs have to be performed by qualified service personnel. Read these instructions. Keep these instructions. Heed all warnings. 4 Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11 Use only attachments/accessories specified by the manufacturer. 12 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13 Unplug this apparatus during lightning storms or when unused for long periods of time. 14 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15 The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection. 16 Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. LEGAL DISCLAIMER TECHNICAL SPECIFICATIONS AND APPEARANCES ARE SUBJECT TO CHANGE WITHOUT NOTICE AND ACCURACY IS NOT GUARANTEED. BEHRINGER, KLARK TEKNIK, MIDAS, BUGERA, AND TURBOSOUND ARE PART OF THE MUSIC GROUP (MUSIC-GROUP.COM). ALL TRADEMARKS ARE THE PROPERTY OF THEIR RESPECTIVE OWNERS. MUSIC GROUP ACCEPTS NO LIABILITY FOR ANY LOSS WHICH MAY BE SUFFERED BY ANY PERSON WHO RELIES EITHER WHOLLY OR IN PART UPON ANY DESCRIPTION, PHOTOGRAPH OR STATEMENT CONTAINED HEREIN. COLORS AND SPECIFICATIONS MAY VARY FROM ACTUAL PRODUCT. MUSIC GROUP PRODUCTS ARE SOLD THROUGH AUTHORIZED FULLFILLERS AND RESELLERS ONLY. FULLFILLERS AND RESELLERS ARE NOT AGENTS OF MUSIC GROUP AND HAVE ABSOLUTELY NO AUTHORITY TO BIND MUSIC GROUP BY ANY EXPRESS OR IMPLIEDUNDERTAKING OR REPRESENTATION. THIS MANUALIS COPYRIGHTED. NO PART OF THIS MANUAL MAYBE REPRODUCED OR TRANSMITTED IN ANY FORMOR BY ANY MEANS, ELECTRONIC OR MECHANICAL,INCLUDING PHOTOCOPYING AND RECORDING OF ANYKIND, FOR ANY PURPOSE WITHOUT THE EXPRESSWRITTEN PERMISSION OF MUSIC GROUP IP LTD. ALL RIGHTS RESERVED. © 2013MUSIC Group IP Ltd. Trident Chambers, Wickhams Cay, P.O. Box 146,Road Town, Tortola, British Virgin Islands LIMITED WARRANTY For the applicable warranty terms and conditions and additional information regarding MUSIC Groups Limited Warranty, please see complete details online at www.music-group.com/warranty. EUROPORT Set-up Step 1: Hook-Up Debate Centre de débat Podiumsdiskussion PPA2000BT/PPA500BT Step 2: Set-up 1,Release the top latch beneath the carrying handle 2,Release the side latches by pressing and then lifting them. 3,Remove the speakers and place them in appropriate locations. 4,Stand the mixer upright.(Make sure the include speaker cables can reach both speakers) Step 3: Controls. FX knob determines how much of each EQ KNOBS adjust the high and low channel’s signal goes to the DIGITAL frequencies for each channel. EFFECTS PROCESSOR. PAN knob positions each channel in the stereo field. LEVEL knob adjusts the CLIP LED lights when the volume of the individual input signals overloads the channel in the overall mix. channel. MULTI-FX PROCESSOR unit adds a selected sound effect to any channels which have their PROGRAM[PUSH] EFFECTS knob controls the effects Effects include reverb, chorus, controls the amount of settings. Rotate this knob delay, and pitch shifter. effects added to the to scroll through the effect patches, and select a patch. push to knob turned up. FX[LEVEL] main mix. knob GRAPHIC adjusts EQ EQ specific activates button FBQ the GRAPHIC EQ. frequencies in the sound spectrum. button MAIN adjusts the overall volume of detection system. the main mix. The MODE The EQ IN button switch selects stereo or mono must operation. also be feature to work. IN the STEREO CHANNELS accept and right connects, CD players, channel input signal by 20dB. sends from a single sound source using sub-mixers, or other Engage this button if the CLIP either RCA cables or14’’ TS plugs. line-level LED lights up on a channel. jack source using cables with ¼" plugs. These accept balanced jacks both and PAD function reduces CONTROL activates the FBQ activated for this LINE LEVEL AUX IN inputs route stereo signals directly into the main mix through either a sginle1/8’’TRS stereo plug or left and 1/4’’plugs DIGITAL WEIRELESS USB MIC INPUT PHANTOM button input optional jacks sends wireless dynamic(hand phantom power to microphone receiver. The LEDs held)or power indicate condenser microphones. accepts the BEHRINGER signal wireless wireless input, microphone connecting microphone the system disables the MIC 1 and MIC 2 accept 48V BLUETOOTH of button and indicator connect your Bluetooth device. condenser microphones using PATRING XLR cables. SUB OUT FX jack sends the FOOTSW low jack connects frequencies of an optional the main mono footswitch signal to an using a 14’’ active TRS plug subwoofer ot right STEREO AUX IN RECORDING OUT inputs stereo send the main mix signal out to signals directly into the an external recording device or main mix through either another mixer. route a signal’s 1/8’’ TRS stereo plug or left and right 1/4’’plugs. SPEAKER OUTPUTS connect to the speakers using speaker cables with 1/4;;plugs.DO NOT USE INTRUMENT CABLES AND ONLY USE THE INCLUDED SPEAKERS. jacks POWER switch turns the power to the unit on and off . POWER SOURCE accepts the included IEC power cable into this jack. Step 4: Getting started 1,Connect the included speaker cables to the speakers and to the rear SPEAKER OUTPUTS on the mixer. 2, Make all the appropriate audio connections to the mixer. Power down all external devices. 3, Set all the channel controls as shown (TREBLE, BASS, and BAL centered; EFFECTS and LEVEL down/off). 4,Center the GRAPHIC EQ faders. 5, Set the MAIN LEVEL CONTROL knobs all the way down. 6,Power up all external devices. 7, Power up the PPA2000BT/PPA500BT by pressing the POWER button. 8,If you are using BEHRINGER wireless microphones, plug the wireless dongle into the DIGITAL WIRELESS USB input, The DIGITAL WIRELESS LEDs will light up when the wireless microphones become active. 9, Slowly turn the MAIN LEVEL CONTROL knobs up 1/3 of the way. 10, Adjust the relative levels of microphones 11, If a channel’s CLIP LED lights, press the PAD button. If the PAD button is already engaged, turn the LEVEL knob down. Always use the pad button with line level inputs. 12, Adjust the left-right position of a channel in the stereo field by turning the channel’s PAN knob. 13, Make final volume adjustments using the MAIN LEVEL CONTROL knobs. Step 5: Adding Effects 1,Set the FX [LEVEL] knob on the DIGITAL EFFECTS PROCESSOR to approximately a 75% setting. 2, Scroll through the available effects by turning the PROGRAM [PUSH] knob. The number in the display will flash. 3, Press the PROGRAM [PUSH] knob to select the effect. The number will stop flashing. 4, While speaking, singing, or playing, turn the channel FX knob up to the desired level on each channel to which you wish to add effects. 5, Adjust the FX [LEVEL] knob on the DIGITAL EFFECTS PROCESSOR up or down from the initial 75% setting to achieve your desired overall effects level in the main mix. Step 6: Feedback Detection “Feedback” is the undesirable high-pitched sound created by sound waves looping between the speakers and the microphones. 1, If feedback occurs, press the EQ and FBQ ON buttons. 2, An LED will light on the EQ slider that corresponds with the specific sound frequency feeding back. 3, Lower the lit EQ slider until feedback stops. Specifications INPUTS 1-4 Type 4xXLR,electronically balanced 4x1/4TRS jack, electronically balanced Impedance Approx2.2 kohm, balanced Approx 1.1 kohm, unbalanced Input -21 dBu @PAD/OFF Max.gain +30dB to +10dB Phantom power supply +48V Signal-to-noise ratio -90dB, A-weighted Channel separation 70dB INPUTS 5-8 Type 4x1/4TS jack, unbalanced 4xRCA jack, unbalanced Impedance Approx,20ohm, unbalanced Input sensitivity -15dBu Max.gain +20dB Signal-to-noise ratio -85dB,A-weighted STEREO AUXIN Type 1x1/4TS jack, unbalanced 1x stereo minijack, unbalanced Impedance 100Kohm, unbalanced Input sensitivity -8dBu Signal-to-noise ratio -90dB,A-weighted TAPE OUT Type 2x RCA , unbalanced Impedance Approx 1Kohm Max.output level +17dB, unbalanced Channel separation >70 dB SUB OUT Type 1x1/4 mono jack, unbalanced Impedance Approx 1Kohm Max.output level +21dBu, unbalanced CHANNEL EQ BASS ±15dB @80Hz TREBLE ±15dB @12kHz EFFECTS Converter 24-bit delta-sigma Sampling frequency 40kHz Display 2-digit, 7-segment EQ Type 7-band LOUDSPEAKER OUTPUTS Type 2x1/4 TS jack Load impedance 8ohm OUTPUT POWER PPA500BT RMS(@8ohm) 2x60 Watts RMS(@4ohm) 2x100 Watts PEAK power(@8ohm) 2x125 Watts PEAK power(@4ohm) 2x250 Watts PPA2000BT RMS(@8ohm) 2x160 Watts RMS(@4ohm) 2x500 Watts PEAK power(@8ohm) 2x250 Watts PEAK power(@4ohm) 2x1000 Watts SYSTEM SPECIFICATIONS Frequency response 50Hz to 20kHz, ±3dB Distortion 0.32%@1W POWER SUPPLY Power consumption 500W for PPA500BT 2000W for PPA2000BT Fuse T 10A H250V(100-120V~,50/60Hz) Power input T 5A H250V(220-240V~,50/60Hz) AC 100-120V,50/60Hz AC 220-240V,50/60Hz DIMENSIONS/WEIGHT Dimensions(HxWxD) Approx.26.0x13.9x34.8 Approx.660x354x883mm Weight Approx.68.34 Ibs/approx.31 kg WIRELESS SYSTEM Connector USB Frequency response 20Hz-15kHz,+0/-3dB Weight Approx.68.34 Ibs/approx.31 kg Range Max 120m BLUETOOTH Frequency Range 2402~2480 MHz Channel Number 79 Version Bluetooth spec V2.1+EDR compliant Output power 4dBm Modulation Type GFSK ,π/4- DQPSK, 8DPSK Date Rate 3 Mb/s
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 24 Creator : cairo 1.10.2 (http://cairographics.org) Producer : cairo 1.10.2 (http://cairographics.org)EXIF Metadata provided by EXIF.tools