NCR RSD Atlanta 2381GRPR 2381 Gripper RFID User Manual 10 0326 Exhibit Cover

NCR Corporation, RSD - Atlanta 2381 Gripper RFID 10 0326 Exhibit Cover

Manual

    5015 B.U. Bowman Drive  Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598   Certification Exhibit     FCC ID:  JEH2381GRPR IC: 470B-2381GRPR  FCC Rule Part: 15.225 IC Radio Standards Specification: RSS-210   ACS Report Number:  10-0326.W06.11.A  Manufacturer: NCR Corporation Model: 2381GRPR     Manual
                            NCR SelfServ Entertainment 2381 Gripper RFID User Guide
 - 2 - FCC Compliance  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.  This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.  If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.  Warning: Changes or modifications to this device not expressly approved by NCR could void the user’s authority to operate the equipment.   IC Compliance  This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  Cet appareillage numérique de la classe B répond à toutes les exigences de l'interférence canadienne causant des règlements d'équipement. L'opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l'interférence nocive, et (2) ce dispositif doit accepter n'importe quelle interférence reçue, y compris l'interférence qui peut causer l'opération peu désirée.
 - 3 - Who Should Use This Document  This user guide is intended for use by anyone seeking to operate the 2381 Gripper RFID reader independently from the 2381 DVD kiosk as a stand-alone RFID reader.    Parts Identification  The 2381 Gripper RFID module and unique USB cable is pictured below.  Observe that the antenna is integrated into the center of the reader PCBA.  A 3.3V/5V dual output power supply is required to power the reader.     Figure 1
 - 4 - System Setup  You will need: • PC or laptop running Windows XP • 3.3V/5V dual output power supply • Power supply cable • Microsoft .NET 3.5 • HID terminal software • 2381 FCC Test Firmware  IMPORTANT: You must obtain and update the 2381 Gripper RFID board with FCC Test Firmware before using the reader in a stand-alone configuration.  Refer to the 2381 Installation Guide for firmware update instructions.  Connect the power cable (foreground) and power supply to the board.  Pin 7 (red) must be connected to +5V, connect pin 1 (black) to ground, and connect pin 5 (white) to +3.3V.    Figure 2   Next, locate the RFID module’s USB connector on the top side of the PCBA, and connect the 2381 Gripper RFID PCBA to a Windows PC or laptop with the supplied USB cable.    Figure 3
 - 5 - Operation  Open a HID terminal session by selecting the NCR DVD Vending Kiosk HID Terminal icon from the desktop.  Accept the default options and click on the Connect button.  Then select rfid from the main menu.       Figure 4   Select option 4, Gripper RFID Test, to initiate an ISO15693 inventory command, and then present an RFID tag to the RFID antenna.  The reader will repeatedly send inventory commands until it is interrupted.  The terminal will display the UID of any RFID tag that responds to the command.  Press a key to terminate the continuous modulation from the repeating inventory command transmissions.       Figure 5   Select option 6, Gripper RFID On, to generate a continuous wave (CW) tone.  The reader will continue to generate a CW tone until it is terminated with the Gripper RFID Test option or until power is removed from the device.

Navigation menu