NEC Platforms 275 2.4 GHz Wireless Transceiver Module User Manual ZBFS SP
NEC Engineering, Ltd. 2.4 GHz Wireless Transceiver Module ZBFS SP
User Manual
2.4GHz ZigBee® wireless transceiver module 「ZB24TM-Z2750」 The ZB24TM-Z2750 embedded RF modules provide wireless connectivity using the ZigBee PRO Feature Set. Product Photo < Features> ・ Integrated by MCU, RF circuits, antenna ・ Communicated by the functions of device detect and data transmission ・ ZigBee mesh networking protocol ・ Controlled by UART I/F ・ Low power sleep mode only End Device ・ DC2.0-3.6V supply voltage ・ FCC certification, Japan Radio Law Document Number July 2011(rev.1.0) IT471-A0057-X309 <Specifications> Product name Carrier frequency Communication protocol Modulation Wireless bit rate Transmit Power Effective range Interface ZB24TM-Z2750 2400MHz~2483.5MHz (16 channel) ZigBee2007® protocol using the ZigBee PRO Feature Set DS-SS (Direct Sequence Spectrum Spread) Maximum 250Kbps (Subject to the communication environment) Maximum 3mW (At the feeding point of the antenna) About 200m (Reference value) ・UART serial communication Data length: 8bit Baud rate : 115.2kbps Parity: no parity Stop: 1stop bit Flow control: hardware (RTS/CTS) Supply Voltage Current Consumption Operating conditions Weight Dimensions Restrictions Reguration Document Number July 2011(rev.1.0) ・2.0 - 3.6VDC ・TX: Typ. 34mA (2.5dBm), Typ. 29mA (1dBm) ・RX: Typ. 24mA ・Sleep Mode : Typ. 1uA (End Device only) (power-supply voltage 3.0VDC) ・Operating temperature range:-10℃~+75℃ ・Operating humidity range:85%RH or less (No do be dewy) Aprox. 2g 24mm×16.5mm×3.9mm (D×W×H) RoHS-Compliant (Pb free) FCC certification, Japan Radio Law IT471-A0057-X309 <FCC statement> This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Modifications not expressly approved by NEC Engineering, Ltd. could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Radiofrequency radiation exposure Information: The radiated output power of the device is far below the FCC radio frequency exposure limits. Nevertheless, the device shall be used in such a manner that the potential for human contact during normal operation is minimized. Document Number July 2011(rev.1.0) IT471-A0057-X309 <output I/F connector> Module connector type product name Signal level : Stacking connector 20pin 0.5mm pitch : JST 20R-JMCS-G-TF(NSA) Receptacle : CMOS Connecting Device Product name Connector type Stacking height : JST 20P3.0-JMCS-G-TF(N) Plug(Recommended) : Stacking connector 20pin 0.5mm pitch : Stacking height 3mm ・Module pin definitions Pin No. Type VDD power Power - GND GND GND - TxD OUT UART transmitted data HiZ RxD IN UART received data HiZ WAKEUP IN Reserved Hi Pull-up RESET IN Reserved Hi Pull-up SSN IN Reserved - SCK IN/OUT Reserved - MOSI IN/OUT LED4 - Internal pull-up 10 MISO IN/OUT LED3 - Internal pull-up 11 VDD power Power - 3.0VDC(Recommend power supply voltage) 12 GND GND GND - 13 GND GND GND - 14 CTS IN Clear to send - 15 RTS OUT Ready to send/LED1 - 16 DBG_DC IN/OUT Reserved - 17 DBG_DD IN/OUT Reserved - 18 FCS IN/OUT Reserved - 19 MODE OUT LED2 Hi 20 GND GND GND - Document Number July 2011(rev.1.0) Definition State of reset Pin name IT471-A0057-X309 Detail 3.0VDC(Recommended power supply voltage) Internal pull-up Pull-up <Dimensions> unit:mm 16.5 14.5 cap 20pin Staking connector ※Staking hight 3mm Top view Contact NEC Engineering,Ltd. General inquiries Sales&Marketing Division 4-10-27 Higashishinagawa Shinagawa-ku Tokyo 140-0002 Japan TEL: +81 3 6713 1200 URL http://www.nec.co.jp/solution/engsl/pro/zigbee/ Document Number July 2011(rev.1.0) IT471-A0057-X309 Side view
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:39 Producer : Acrobat Distiller 8.3.0 (Windows) Company : NEC Engineering,Ltd. Source Modified : D:20110716082640 Create Date : 2011:07:16 17:27:12+09:00 Creator Tool : Word 用 Acrobat PDFMaker 8.1 Modify Date : 2011:07:16 17:27:26+09:00 Metadata Date : 2011:07:16 17:27:26+09:00 Document ID : uuid:9e1d2f72-2094-41b4-8e50-dc9fa4000fce Instance ID : uuid:ea095781-93b8-4fd9-9fbb-ed363a1c6fcc Subject : 16 Format : application/pdf Creator : Hiroaki Takahashi Title : ZBFS-SP仕様書 Page Count : 5 Page Layout : OneColumn Author : Hiroaki TakahashiEXIF Metadata provided by EXIF.tools