NEC of America 7N2P11 PCS GSM Phone with RFID User Manual

NEC Corporation of America PCS GSM Phone with RFID Users Manual

a href="https://usermanual.wiki/NEC-of-America" itemprop="url"> NEC of America >

Contents

Users Manual

1Continued on next pageMaking a Voice/Videophone Call1Enter the phone number of the other partyThe “Enter phone number screen” appears. Always start by entering the area code, even for calls within the same area. You can enter up to 80 digits for the phone number. However, only the last 26 digits are displayed. <When you enter a wrong number>■To insert a numberPress v to move the cursor to the number to the left of the position where you want to insert the number, then enter the number. ■To delete a numberPress v to move the cursor to the number you want to delete, then press t. Hold down t for 1 second or longer to delete all the numbers to the left of the cursor and the number in the cursor position. ■To re-enter the numberMove the cursor to the beginning or end of the number and hold down t for 1 second or longer to return to the standby screen. 2r (voice call) /o (V. phone)* As FOMA N706i is not equipped with the front camera, during a videophone call, you can send only the substitute image (Chara-den) or image from the rear camera to the other party. You can change the substitute image (Chara-den) to other data such as an image of My picture in “Select image”.<Videophone>■To change the substitute image (Chara-den)XFu (FUNC)X“Select image”X“Chara-den” XSelect Chara-denEnter phone number<Voice call>The “In-call screen” appears. “ ” flashes while dialing and lights up during the call. ■If you hear the busy toneThe line is busy. Call again after a while. ■If you hear a message saying that the other party cannot be reachedThe other party’s mobile phone is not turned on or is out of signal range. Call again after a while. ■If you hear a message requesting your caller IDCall again with caller ID notification enabled. <Videophone>The “Videophone in-call screen” appears. “ ” flashes while dialing a videophone call and lights up during the call. ■If a videophone call is not connected→P. 2■To switch between substitute image and camera imageXFDd (Change)Each time you press FDd (Change), the substitute image and camera image switches. ■To switch the main screenXDd (1 second or longer)■To enlarge the image to be sentXAdjust the zoom using Fv■To mute the voice to sendXSa (マナー ) (1 second or longer)The “ ” icon is displayed. To cancel muting, press Sa ( マナー ) for 1 second or longer again. In-callVideophone in-call
2■To switch a voice/videophone call during a call→P. 3■When the 2in1 is in Dual modeThe Outgoing number selection screen appears. Select a phone number. 3To end the call, press y●If a videophone call is not connectedWhen a videophone call is not connected, the cause of the failure appears. zThe cause may not appear depending on the situation. zDepending on the type of other party’s phone or the possible lack of a network service subscription, the reason may not accurately reflect the other party’s actual status. zIf the videophone call is not connected, your call is automatically switched to a voice call when you set “Auto redial as voice” to “ON”. However, the call may not be handled in this way if you call an ISDN synchronous 64K or an ISDN videophone which does not support the 3G-324M standard (as of May, 2008) or if you dial a wrong number. Note that call charge may be applied in some cases.Display CauseCheck number then redialThe called phone number is not usedBusy The line is busy• This message may also appear during packet communication. Busy with packet transmissionThe other party is using packet communicationOut of service area/power offThe other party is out of service area or the phone is turned offSet caller ID to ON You connected without notifying your caller ID (when dialing into visualnet, etc.)Your call is being forwardedThe call is being forwarded (A Videophone call is made when the forwarding number is for a 3G-324M-compatible videophone)Redial using voice callThe phone for the forwarding number is not compatible with videophone callsPlease activate caller ID before dialing againThe other party sets the Caller ID request serviceAt the use’s request, your call cannot be connectedThe other party sets the Nuisance call blocking serviceUpper limit has been exceeded Connection failedThe upper limit set for a Limit billing plan (Type Limit and Family Wide Limit) is exceededConnection failed Set the caller ID notification to “ON” and retry• This message may also appear in other situationsPlease make your call from the i-mode web pageYou attempted to make a videophone call to watch V-live without browsing the i-mode official siteDisplay Cause
Download:
Mirror Download [FCC.gov]
Document ID935556
Application IDlkYuLcZuKEsVBzA+i/Wm6g==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize64.39kB (804886 bits)
Date Submitted2008-04-30 00:00:00
Date Available2008-10-27 00:00:00
Creation Date2008-04-30 15:51:55
Producing SoftwareAcrobat Distiller 7.0 (Windows)
Document Lastmod2008-04-30 11:59:04
Document TitleUsers Manual
Document CreatorPScript5.dll Version 5.2
FCC ID Filing: A98-7N2P11

Navigation menu