NEC of America AZB9304 Cellular WCDMA/ HSDPA Phone with Bluetooth and WLAN User Manual RF Warning Info

Download:
Mirror Download [FCC.gov]
Document ID	1275314
Application ID	XvsIMxvZQIdV84wUauT4/Q==
Document Description	RF Warning Info
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	1.11kB (13927 bits)
Date Submitted	2010-04-30 00:00:00
Date Available	2010-10-27 00:00:00
Creation Date	2017-11-09 15:05:45
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-11-09 15:05:45
Document Title	Microsoft Word - A98-AZB9304 RF Warning Page Rev5.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	217216X009122

Radio Frequency (RF) Signals
THIS MODEL DEVICE MEETS THE U.S. GOVERNMENT’S REQUIREMENTS FOR
EXPOSURE TO RADIO WAVES.
Your wireless device contains a radio transmitter and receiver. Your device is designed and
manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set
by the Federal Communications Commission of the U.S. Government. These limits are part of
comprehensive guidelines and establish permitted levels of RF energy for the general population.
The guidelines are based on standards that were developed by independent scientific
organizations through periodic and thorough evaluation of scientific studies.
The exposure standard for wireless mobile devices employs a unit of measurement known as the
Specific Absorption Rate (SAR). The SAR limit set by the FCC is 1.6 W/kg.* Tests for SAR are
conducted using standard operating positions accepted by the FCC with the device transmitting
at its highest certified power level in all tested frequency bands. Although the SAR is determined
at the highest certified power level, the actual SAR level of the device while operating can be well
below the maximum value. This is because the device is designed to operate at multiple power
levels so as to use only the power required to reach the network. In general, the closer you are to
a wireless base station antenna, the lower the output.
Before a device model is available for sale to the public, it must be tested and certified to the FCC
that it does not exceed the limit established by the U.S. government-adopted requirement for safe
exposure. The highest SAR value for this model device as reported to the FCC is 0.34 W/kg.
While there may be differences between the SAR levels of various devices and at various
positions, they all meet the U.S. government requirement.
The FCC has granted an Equipment Authorization for this model device with all reported SAR
levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this
model device is on file with the FCC and can be found under the Display Grant section at https://
gullfoss2.fcc.gov/oetcf/eas/reports/GenericSearch.cfm after search on FCC ID A98-AZB9304.
There are no body-worn accessories for this device.
_____________________________________________________________________________
* In the United States, the SAR limit for wireless mobile devices used by the public is 1.6 watts/kg
(W/kg) averaged over one gram of tissue. SAR values may vary depending upon national
reporting requirements and the network band.
FCC Regulations
This mobile device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
This mobile device has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation; if this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Extract
Author                          : 217216X009122
Create Date                     : 2010:04:30 14:05:03-05:00
Modify Date                     : 2010:04:30 17:15:37-04:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2010:04:30 17:15:37-04:00
Producer                        : Acrobat Distiller 9.3.2 (Windows)
Format                          : application/pdf
Title                           : Microsoft Word - A98-AZB9304 RF Warning Page Rev5.doc
Creator                         : 217216X009122
Document ID                     : uuid:ae614381-3255-4728-bc5a-7043ad8a6d6c
Instance ID                     : uuid:35becab1-4e7a-4624-bc98-bde30a871863
Page Count                      : 2

EXIF Metadata provided by EXIF.tools