NEC of America N905IMYUH PCS GSM Phone with RFID User Manual

NEC Corporation of America PCS GSM Phone with RFID

Users Manual

357Appendix/External Devices/TroubleshootingSpecific Absorption Rate of Mobile Phones, etc.Specific Absorption Rate (SAR)This model phone N905iµ meets the MIC’s*1 technical regulation for exposure to radio waves. The technical regulation established permitted levels of radio frequency energy, based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The regulation employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit is 2 watts/kilogram (W/kg)*2 averaged over ten grams of tissue. The limit includes a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The value of the limit is equal to the international guidelines recommended by ICNIRP*3. All phone models should be confirmed to comply with the regulation, before they are available for sale to the public. The highest SAR value for this model phone N905iµ is 0.78 W/kg. It was taken by the Telecom Engineering Center (TELEC), a Registered Certification Agency on the Radio Law. The test for SAR was conducted in accordance with the MIC testing procedure using standard operating positions with the phone transmitting at its highest permitted power level in all tested frequency bands. While there may be differences between the SAR levels of various phones and at various positions, they all meet the MIC’s technical regulation. Although the SAR is determined at the highest certified power level, the actual SAR of the phone during operation can be well below the maximum value. For further information about SAR, please visit the following websites:Radio Frequency (RF) SignalsTHIS MODEL PHONE MEETS THE U.S. GOVERNMENT'S REQUIREMENTS FOR EXPOSURE TO RADIO WAVES. Your wireless phone contains a radio transmitter and receiver. Your phone is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. World Health Organization (WHO): http://www.who.int/peh-emf/ICNIRP: http://www.icnirp.de/MIC: http://www.tele.soumu.go.jp/e/ele/body/index.htmTELEC: http://www.telec.or.jp/ENG/Index_e.htmNTT DoCoMo: http://www.nttdocomo.co.jp/english/product/NEC: http://www.n-keitai.com/lineup/ (in Japanese only)Association of Radio Industries and Businesses: http://www.arib-emf.org/index.html (in Japaneseonly)*1：Ministry of Internet Affairs and Communications*2：The technical regulation is provided in Article 14-2 of the Ministry Ordinance RegulatingRadio Equipment.*3：International Commission on Non-lonizing Radiation Protection
358Appendix/External Devices/TroubleshootingThe exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate (SAR). The SAR limit set by the FCC is 1.6 W/kg.* Tests for SAR are conducted using standard operating positions accepted by the FCC with the phone transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the output. Before a phone model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the U.S. government-adopted requirement for safe exposure. The tests are performed on position and locations (for example, at the ear and worn on the body) as required by FCC for each model. The highest SAR value for this model phone as reported to the FCC when tested for use at the ear is 0.78 W/kg, and when worn on the body, is 0.288 W/kg. (Body-worn measurements differ among phone models, depending upon available accessories and FCC requirements). While there may be differences between the SAR levels of various phones and at various positions, they all meet the U.S. government requirement. The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model phone is on file with the FCC and can be found under the Display Grant section at https://gullfoss2.fcc.gov/oetcf/eas/reports/GenericSearch.cfm after search on FCC ID A98-N905IMYUH. For body worn operation, this phone has been tested and meets the FCC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that contains no metal and that positions the handset a minimum of 1.5 cm from the body.FCC RegulationsThis mobile phone complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This mobile phone has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation; if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:eReorient or relocate the receiving antenna.eIncrease the separation between the equipment and receiver.eConnect the equipment into an outlet on a circuit different from that to which the receiver is connected.eConsult the dealer or an experienced radio/TV technician for help.Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.*In the United States, the SAR limit for wireless mobile phones used by the public is 1.6 watts/kg (W/kg) averaged over one gram of tissue. SAR values may vary depending upon national reporting requirements and the network band.
359Appendix/External Devices/TroubleshootingDeclaration of ConformityThis mobile phone complies with the EU requirements for exposure to radio waves.Your mobile phone is a radio transceiver, designed and manufactured not to exceed the SAR* limits** for exposure to radio-frequency (RF) energy, which SAR* value, when tested for compliance against the standard was 0.918 W/kg. While there may be differences between the SAR* levels of various phones and at various positions, they all meet*** the EU requirements for RF exposure.*: The exposure standard for mobile phones employs a unit of measurement known as the Specific Absorption Rate,or SAR.**: The SAR limit for mobile phones used by the public is 2.0 watts/kilogram (W/kg) averaged over ten grams oftissue, recommended by The Council of the European Union. The limit incorporates a substantial margin of safetyto give additional protection for the public and to account for any variations in measurements.***: Tests for SAR have been conducted using standard operating positions with the phone transmitting at its highestcertified power level in all tested frequency bands. Although the SAR is determined at the highest certified powerlevel, the actual SAR level of the phone while operating can be well below the maximum value. This is because thephone is designed to operate at multiple power levels so as to use only the power required to reach the network. Ingeneral, the closer you are to a base station antenna, the lower the power output.The product “N905iµ” is declared to conform with the essential requirements of European Union Directive1999/5/EC Radio and Telecommunications Terminal Equipment Directive 3.1(a), 3.1 (b) and 3.2. TheDeclaration of Conformity can be found on http://www.n-keitai.com/lineup/index.html (Japanese only).
360Appendix/External Devices/Troubleshooting
1Making/Receiving CallsMaking a Voice/Videophone Call1Dial the other party’s number, starting with the area codeThe “Phone number entry” screen appears.Always start with the area code, even for calls within the same area. A number of up to 80 digits can be entered for making a call although the numbers disappear from the display one by one from the beginning after the number exceeds 26 digits.2rThe phone number disappears briefly and then reappears from the right as it is dialed. The “ ” icon flashes during dialing and remains lit during a call.The “FOMA voice in-call” screen appears.■To switch to a videophone call during a voice call"Changing a call from voice to videophone"→p.3■If you hear the busy toneThe line is busy. Press y, and call again after a while. ■If you hear the message saying that the other party cannot be reachedThe other party's mobile phone or PHS phone is not switched on or is out of signal range. Press y , and call again after a while. ■If you hear the message requesting your caller IDThe other party has set the Caller ID Request service to "Activate". Call again with your caller ID shown. ■If you set "2in1 setting" to "Dual mode"The outgoing number selection screen appears. Select a phone number. 3To end the call, press ydMaking a videophone call1Phone number entry screen Xo ()The "Videophone in-call" screen appears. You can talk hearing the other party's voice through the speaker. The " " icon flashes during dialing and remains lit during a videophone call. ■To switch to a voice call during a videophone call"Changing a call from videophone to voice"→p.3■To switch between camera image and substitute image during a videophone callXSelect "Substitute image" or "My side" from the function menu. ■To mute voice to send during a videophone call (microphone mute)Xa (1 second or longer)" " appears while in mute. Video is transmitted as it is. To cancel mute, press a again for 1 second or longer. 2To end the call, press y−−Area code Local code Phone numberＶ ｐｈｏｎｅ．
2Making/Receiving CallsdIf you entered a wrong phone number■To insert a numberPress h or j to move highlight to the number on the left of the insert position and enter the number. ■To delete a numberPress h or j to move highlight to the number to delete and press t. Pressing t for 1 second or longer deletes the highlighted number and all numbers on the left side of the highlighted number. ■To reenter a numberMove highlight to the beginning or end of the number and press t for 1 second or longer to return to the standby screen. dIf a videophone call is not connectedIf a videophone call is not connected, a message giving the reason for the connection failure appears. However, in some circumstances, an explanatory message may not be displayed. Also, depending on the type of phone used by the other party and the possible lack of a network service subscription, the reason given may not accurately reflect the other party's actual status. *: This message may also appear during packet communication depending on the type of other party's terminal. Message ReasonCheck number then redial The dialed phone number is currently not used. Busy*The line is busy. Busy with packet transmission Packet communication is in progress on the other party. Out of service area/power off The other party's phone is out of service or the power is turned off. Set caller ID to ONThe call is connected without showing your caller ID (when dialing visualnet). Your call is being forwarded The call is being forwarded (into a videophone call if the forwarding party has a videophone that complies with 3G-324M). Redial using voice call The forwarded party is non-videophone-terminal.Please activate caller ID before dialing again The Caller ID Request service is set on the other party.At the user's request, your call can not be connected The Nuisance Call Blocking service is set on the other party. Upper limit has been exceeded Connection failed The upper limit set for a Limit billing plan (Type Limit and Family Wide limit) is exceeded. Connection failed Set "Caller ID Notification" to "ON" and then try again. aThis message may also be displayed in other situations. Please make your call from the i-mode web page You attempted to make a videophone call to watch V-live without browsing the i-mode official site.
3Making/Receiving CallsChanging a Call from FOMA Voice to VideophonedYou can only change the call mode when you are the caller. When you are a callee, you cannot change the call mode. dYou can repeatedly change the call mode between voice and videophone. dChanging a call from voice to videophoneYou can change the call mode during a voice call you dialed. dIf the other party uses a FOMA terminal that can change the call mode, " " appears during a voice call and you can change the call mode between voice and videophone. (This function is available between terminals that support change between voice call and videophone call.)1In-call screenXd ()X"YES"While a voice call is being changed to a videophone call, the screen showing that the call mode is being changed appears and the voice guidance is given. Select "NO" on the "Ntfy switch-mode" message screen to return to the in-call screen. dChanging a call from videophone to voiceThe caller can change the call mode to voice during a videophone call. dIf the handset of other party is a FOMA terminal supporting the call change, "Change to voice" can be selected from the function menu during a videophone call and you can change the call mode. (This function is available between terminals that support change between voice call and videophone call.)1Videophone in-call screenX[ch] (FUNC)X"Change to voice"While the call mode is being changed from videophone to voice, the screen showing that the call mode is being changed appears and the voice guidance is given. <WORLD CALL>Making International CallsWORLD CALL is an international dialing service available for DoCoMo mobile phones. FOMA service subscribers have also subscribed to "WORLD CALL" (excluding those who indicated that they did not require the service). * This service is unavailable with some billing plans. dWORLD CALL is available for calls to around 240 countries and regions worldwide. dWORLD CALL is included in the bill for your monthly call charges. dIn addition to dialing a phone number, you can make an international call by adding "+" or selecting "Int'l call" or "Prefix numbers" from the function menu on the phone number entry, Redial/Dialed calls, Received calls or phonebook detail screen. Changes to the international dialing procedure Since communication from mobile devices such as mobile phones is not covered by the "MY LINE" service, this service cannot be used to access WORLD CALL. However, with the introduction of the "MY LINE" service, the procedure used to make international calls from a mobile phone has changed. Note that the conventional dialing procedure (the one described below with "010" removed) can no longer be used. For additional information regarding WORLD CALL, refer to the contact information provided on the back cover of this manual. “International videophone calls” can be made to users of some specific overseas 3G mobile terminals by pressing o ( ) to make a call after following the dialing procedure below.cSee the DoCoMo website for information about accessible countries and carriers.cDepending on the type of the phone used by the other party, the other party’s image shown on your FOMA terminal may be distorted during an international videophone call or the connection may fail.Ｖ ｐｈｏｎｅ．Ｖ ｐｈｏｎｅ．Ｖ．ｐｈｏｎｅ
4Making/Receiving CallsDialing to make an international call1Dial a number in the following order: 009130→010→(country code)→(area code (long distance code))→(the other party's phone number)If an area code begins with a zero (0), omit the zero. However, when you call some countries or regions such as Italy, "0" may be required. 2rAn international call is made.3To end the call, press yUsing “+” to make an international callUsing the "+" prefix allows you to make international calls without having to dial an IDD prefix code (e.g. 009130-010). d"Auto int’l call set." in "Int'l dial assistance" is set to "ON" (automatically added) at the time of purchase so that a FOMA terminal automatically dials the IDD prefix code. 1On the standby screen, dial the following: + (0 (1 second or longer))→(country code)→(area code)→(other party’s phone number)If an area code begins with a zero (0), omit the zero. However, when you call some countries or regions such as Italy, "0" may be required. 2rX“Dial”An international call is made. ■To make a call without converting "+" into the IDD prefix codeX"Original phone No."* This function is unavailable for your FOMA terminal. ■To cancel a callX"Cancel"Making an international call with international call codes added <Int'l call>Add a country code or IDD prefix code to a phone number to make an international call. dThis function is available on the phone number entry screen and the detail screens of phonebook, Received calls, Dialed calls and Redial. <Example: To use the Int'l call function on the phone number entry screen>1Enter the other party's phone number2[ch] (FUNC)X"Int'l call"XSelect a country codeXSelect an international access name (IDD prefix code)The selected country code and IDD prefix code are added. If an area code begins with a zero (0), the zero is automatically deleted. If "イタリア" (Italy) is selected for the country code, the zero is not deleted. 3r
5Making/Receiving CallsdConverting “+” automaticallySet this function to add “+” automatically when making international calls.1iX"SETTINGS"X"Dialing"X"Int'l dial assistance"X"Country Code setting"2Select a country codeXSelect an IDD prefix codedEditing a country codeSee the DoCoMo website for more information about country codes.1iX"SETTINGS"X"Dialing"X"Int'l dial assistance"X"Country Code setting"The "Country Code set" screen appears.2Highlight an item and press o (Edit)3Enter a country nameXEnter a country codedStoring an IDD prefix codeYou can store up to 3 IDD prefix codes, each of 10 digits max.1iX"SETTINGS"X“Dialing”X"Int'l dial assistance"X"IDD Prefix setting"2Highlight “<Not recorded>” and press o (Edit)■To edit a stored itemXHighlight an item to edit and press o (Edit)3Enter an international access name4Enter the IDD prefix code
6Making/Receiving CallsUsing the Redial/Received Calls RecorddDialing a previously dialed number <Redial/Dialed calls>Information such as a phone number, date and time you called is recorded as the Redial/Dialed calls record. dThe Redial record can hold up to 30 phone numbers for voice call, videophone call and PushTalk call entries. The Dialed calls record can hold up to 30 voice call, videophone call and PushTalk call entries and up to 30 packet communication and 64K data communication entries. dIf you have dialed to the same phone number twice or more, only the latest call is logged in the Redial record while all the calls are logged in the Dialed calls record. dWhen the number of Redial/Dialed calls record entries exceeds the maximum, existing entries are overwritten starting with the oldest one. dYou cannot view the Redial/Dialed calls record during a videophone call. 1On the standby screenXj2Select a Redial/Dialed calls record entry to check3r or d 4To end the call, press yReceiving a Voice/Videophone Call1When a call arrives, press r or dWhen a call arrives, a FOMA terminal rings, the incoming call lamp flashes and the “Ringing” screen appears.Unless “FOMAphone” under “Vibrator” is set to “OFF”, the FOMA terminal also vibrates to notify you of the call.2To end the call, press ydReceiving a videophone callUse this procedure to receive an incoming videophone call. If you cannot answer a videophone call with your camera image, you can receive the call showing the caller a substitute image instead of your camera image. 1When a videophone call arrives, press o () or rThe "videophone in-call" screen (p.1) appears. You can talk hearing the other party's voice through the speaker. ■To switch between the camera and alternative images during a videophone callXSelect “Substitute image” or “My side” from the function menu.■To send the rear camera image during a videophone callXdDuring a videophone call, you can switch between the front and rear cameras (CHG camera-mode) by pressing d.■To mute voice to be sent during a videophone call (microphone mute)Xa (1 second or longer)" " appears while in mute. Video is transmitted as it is. To cancel mute, press a again for 1 second or longer. 2To end the call, press yＶ ｐｈｏｎｅ．
7Making/Receiving CallsChanging a Call Between Voice and Videophone (the Other Party)The mode of a call you have received can be changed by the caller (the other party). dYou can only change the call mode when you are a caller. When you have received a call, you cannot change the call mode. (This function is available between terminals that support change between voice call and videophone call.) dTo enable a caller to change the call mode, "Ntfy switch-mode" must be set to "Indication ON" on the caller's phone beforehand.dChanging a call from voice to videophone (the other party)1In-call screenXThe other party changes the call modeX"YES"While the call mode is being changed from voice to videophone, the screen showing that the call mode is being changed appears and the voice guidance is given. The call mode is changed to videophone and a camera image is sent to the caller. ■To send a substitute image to the callerX"NO"The specified substitute image is sent to the caller. <Answer setting> MENU58Using a Dial Key to Receive CallsThis setting enables you to quickly turn off a ring tone or answer the call when you receive a voice, videophone or PushTalk call. This is useful when you receive a call in a place where a ring tone may disturb people around you.1iX”SETTINGS”X“Incoming call”X“Answer setting”XSelect any itemAny key answer Press one of the following keys to answer a call: Voice call: r, d, 0 to 9, w, t, b, o or aVideophone call: r, d ( ), o ()PushTalk call: P, r, d, 0 to 9, w, t, o or aQuick silent Press one of the following keys or open a FOMA terminal to stop a ring tone or vibrator. When you stop a ring tone or vibrator in this way, the caller continues to hear the ring tone. Voice call*,PushTalk*: 0 to 9, w, t, b, a, or oVideophone call*: 0 to 9, w, t, b, or a*: To answer a call, press r, d, o ( ) (only for videophone) or P (only for PushTalk).OFF Press one of the following keys to answer a call: Voice call: r or dVideophone call*: r, d or o ()PushTalk call: P, r or dDefault settingAny key answerＳｕｂｓｔ． Ｖ ｐｈｏｎｅ．Ｖ ｐｈｏｎｅ．Ｖ ｐｈｏｎｅ．

Navigation menu