NETIS SYSTEMS WF2322R 300Mbps Wireless N High Power Outdoor AP Router User Manual 1

Download:
Mirror Download [FCC.gov]
Document ID	2466507
Application ID	XkdM2Rw9IntEU2gL1mA9gQ==
Document Description	WF2322 User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	83.27kB (1040813 bits)
Date Submitted	2014-12-08 00:00:00
Date Available	2015-05-05 00:00:00
Creation Date	2014-10-24 14:46:53
Producing Software	Corel PDF Engine Version 16.1.0.843
Document Lastmod	2014-10-24 14:46:53
Document Title	未命名 -1
Document Creator	CorelDRAW X6
Document Author:	Administrator

netis Wireless High Power Outdoor AP Router
Quick Installation Guide
Model No. WF2322
WF2370
WF2375
netis Wireless High Power Outdoor AP Router Quick Installation Guide
1.Package Contents
The following items should be found in your package:
netis Wireless High Power Outdoor AP Router
Quick Installation Guide
Outdoor
AP
Router
PoE Injector
Power Adapter Quick Installation Guide Mounting Tie x2
Slip-proof Pad x2
Please make sure that the package contains above items, if any of the listed items are damaged
or missing, please contact your distributor.
* This QIG is for all netis Wireless High Power Outdoor AP Router, including models- WF2322,
WF2375, WF2370, etc.
* The product model shown in this QIG is WF2322, as an example.
2.Hardware Connection
The outdoor AP work in pairs, and work best when they are face to face like below, please try
to adjust their direction and get the best singal:
Please put the slip-proof pads and mounting ties as below:
When device works in Client or WISP mode,
1. Connection Step
A) Remove the small cover of device.
B) Connect one end of the Ethernet cable into the WAN/LAN (
) port of the device and the
other end to the PoE port of the PoE injector.
C) Connect the Power Adapter to DC-in port of the PoE injector and plug the other end to wall outlet.
D) Connect the Ethernet cable into LAN/WAN port of PoE injector and the other end to the Ethernet
port of the PC or AP/switch.
E) Re-place the small cover back to the device.
netis Wireless High Power Outdoor AP Router Quick Installation Guide
For step A)
LAN/WAN
LAN/WAN
Computer
For step B) to E)
2.The connection will be similar to the figure below after the above steps are finished.
INDOOR
Client
Main Electrical Supply
POWER
Power Cable
PoE Injector
LAN/WAN
TO Switch or PC
Ethernet Cable
netis Wireless High Power Outdoor AP Router Quick Installation Guide
ISP
INDOOR
WISP Mode
Main Electrical Supply
POWER
Power Cable
PoE Injector
LAN/WAN
TO Switch or PC
Ethernet Cable
When device works in AP/AP Router mode,
1. Connection step
A) ~ C) is same as above
D) Connect the Ethernet cable into LAN/WAN port of PoE injector and the other end to the Ethernet port
of xDSL or Cable modem/router.
E) Re-place the small cover back to the device
LAN/WAN
LAN/WAN
For step B) to E)
netis Wireless High Power Outdoor AP Router Quick Installation Guide
2.The connection will be similar to the figure below after the above steps are finished.
Internet
INDOOR
AP/AP Router
Main Electrical Supply
POWER
Power Cable
PoE Injector
LAN/WAN
connect to xDSL or
Cable modem/router
Ethernet Cable
3. Configure the AP Router via Web Management Page
This device works in AP mode by default, so if you are intend to change the working mode or
any settings, please connect your computer to
or
Port of AP and set a static IP for
you computer as below steps:
3.1 Set a Static IP for PC
Manually set the IP address of the wired network adapter on your computer as below.
IP Address/ IPv4 Address: 192.168.1.x (1 “Control Panel”.
2) Left-click on “Network and Internet” > “Network and Sharing Center” > “Change
adapter settings” (for Windows 8/ 7)/”Manage network connections” (for Windows Vista).
3) Right-click on “Local Area Connection” and left-click on “Properties”.
4) Double-click on “Internet Protocol Version 4 (TCP/IPv4)”.
5) Select “Use the following IP address” then left-click on “OK”.
For Windows XP/2000
1) Go to “Start” > “Control Panel”.
2) Left-click on “Network and Internet Connections” > “Network Connections”.
3) Right-click on “Local Area Connection” and left-click on “Properties”.
4) Double-click on “Internet Protocol (TCP/IP)”.
5) Select “Use the following IP address” then left-click on “OK”.
For MAC OS
1) Click on the “Apple” menu > “System Preferences”.
2) Click on the “Network” icon.
3) Click on “Ethernet” in the left side box and click on “Advanced” in the lower right corner.
4) In the top options, select “TCP/IP”.
5) In the pull-down menu next to “Configure IPv4” select “Manually”.
6) Fill in the “IPv4 Address/Subnet Mask/Router” parameters, and click “OK” then “Apply”.
netis Wireless High Power Outdoor AP Router Quick Installation Guide
3.2 Open your browser and type http://192.168.1.1 in the address field to visit router's web
management page.
3.3 A dialog box will prompt as below, please enter User name and Password, both default values
are guest and click OK.
Note: The configuration includes “Internet settings” and “Wireless settings”, if you choose “AP”,
please go to Wireless Settings directly.
AP Router Mode:
Select the correct Connection Type.
PPPoE
Select “PPPoE” when：
Type in the Username &
1. WF2322 is connected to a DSL or Cable pure modem.
Password provided by the
2. Got username &password from ISP.
ISP.
3. Broadband connection is needed on PC when bypassing
WF2322.
DHCP
Select “DHCP” when:
(Dynamic IP)
1. WF2322 is connected to a Cable/DSL modem router.
2. Internet works directly on PC when bypassing WF2322.
Static IP
Select “Static IP ” when:
Type in all the IP Info. 1. Got IP Address, Subnet Mask, Default Gateway, DNS
Server from ISP.
netis Wireless High Power Outdoor AP Router Quick Installation Guide
WISP Mode :
Select target network and Connection Type.
1. Click “AP Scan” button to select your target network and click “Connect” button.
2. Type in the wireless security info of the target network.
3. Select connection type. (Please refer to “Internet Settings” →“AP Router Mode”)
Wireless Settings
Setup a wireless network name in “SSID” box, it is recommended to use WPA-PSK/WPA2-PSK for
“Security” and set a wireless network key in the “Password” box, then click “Save” button.
Note: The DHCP Server will be disabled after switching to “AP” mode successfully, so you will have
to set a static IP address for your PC first if you need to login to the web-based management page again.
3.4 The web management page will display after login successfully. Select the language as you need
on the top box, default is in English.
3.5 When you completed the configuration,please remember to change the settings on your computer
back to to 'obtain an IP address automatically' in the the same window as step 3.1.
4.Troubleshooting
Q How do I restore my netis WF2322 to default settings?
A With the router powered on, holding “Reset” button on the PoE injector for 8s~10s with a pin to
restore it to factory defaults.
Q What can I do if my Internet cannot be accessed?
A 1) Check to verify the hardware connections are correct. Please refer to the “Hardware Connection” step.
2) Refer to 3.1) to set a Static IP address for your PC and connect the WF2322 to your PC.
3) Open a web browser and login to http://192.168.1.1
4) Re-check your setting
5) Reboot the modem first and then netis device. Wait for one minute before you check the Internet again.
6) If Internet access is not available, please connect your computer directly to your modem and try
the Internet again.
If the Internet is still not working, please contact your ISP for further help.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
·Reorient or relocate the receiving antenna.
·Increase the separation between the equipment and receiver.
·Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
·Consult the dealer or an experienced radio/TV technician for help.
FCC RF Radiation Exposure Statement:
1. The equipment complies with RF exposure limits set forth for an uncontrolled environment. The antenna(s)
used for this transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
3. This equipment should be installed and operated with a minimum distance of 20 centimeters between
the radiator and your body.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may cause undesired
operation
Technical Support:
USA/ Canada
Toll Free: +1 866 71 network (+1 866 716 3896)
E-mail: usa_support@netis-systems.com
NETIS SYSTEMS CO., LTD.
www.netis-systems.com
MADE IN CHINA
PKUM05621
Other Regions:
E-mail: support@netis-systems.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Profile CMM Type                : Lino
Profile Version                 : 2.1.0
Profile Class                   : Display Device Profile
Color Space Data                : RGB
Profile Connection Space        : XYZ
Profile Date Time               : 1998:02:09 06:49:00
Profile File Signature          : acsp
Primary Platform                : Microsoft Corporation
CMM Flags                       : Not Embedded, Independent
Device Manufacturer             : IEC
Device Model                    : sRGB
Device Attributes               : Reflective, Glossy, Positive, Color
Rendering Intent                : Perceptual
Connection Space Illuminant     : 0.9642 1 0.82491
Profile Creator                 : HP
Profile ID                      : 0
Profile Copyright               : Copyright (c) 1998 Hewlett-Packard Company
Profile Description             : sRGB IEC61966-2.1
Media White Point               : 0.95045 1 1.08905
Media Black Point               : 0 0 0
Red Matrix Column               : 0.43607 0.22249 0.01392
Green Matrix Column             : 0.38515 0.71687 0.09708
Blue Matrix Column              : 0.14307 0.06061 0.7141
Device Mfg Desc                 : IEC http://www.iec.ch
Device Model Desc               : IEC 61966-2.1 Default RGB colour space - sRGB
Viewing Cond Desc               : Reference Viewing Condition in IEC61966-2.1
Viewing Cond Illuminant         : 19.6445 20.3718 16.8089
Viewing Cond Surround           : 3.92889 4.07439 3.36179
Viewing Cond Illuminant Type    : D50
Luminance                       : 76.03647 80 87.12462
Measurement Observer            : CIE 1931
Measurement Backing             : 0 0 0
Measurement Geometry            : Unknown
Measurement Flare               : 0.999%
Measurement Illuminant          : D65
Technology                      : Cathode Ray Tube Display
Red Tone Reproduction Curve     : (Binary data 2060 bytes, use -b option to extract)
Green Tone Reproduction Curve   : (Binary data 2060 bytes, use -b option to extract)
Blue Tone Reproduction Curve    : (Binary data 2060 bytes, use -b option to extract)
Page Count                      : 8
Create Date                     : 2014:10:24 14:46:53+08:00
Modify Date                     : 2014:10:24 14:46:53+08:00
Producer                        : Corel PDF Engine Version 16.1.0.843
Author                          : Administrator
Creator                         : CorelDRAW X6
Title                           : 未命名 -1

EXIF Metadata provided by EXIF.tools