NEXXT SOLUTIONS ION150 150Mbps Wireless N PCI-E Adapter User Manual 1

NEXXT SOLUTIONS 150Mbps Wireless N PCI-E Adapter 1

UserManual.wiki >

NEXXT SOLUTIONS >

ION150 User Manual

NW230NXT45 User Guide

Unmatched wireless performance, reception, and security protection The Ion-150 allows you to easily upgrade or expand your wireless connectivityFast Ethernet AdapterModel: NW230NXT45Ion150150Mbps WIRELESS N PCI-E ADAPTERUser Guide

FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:t Reorient or relocate the receiving antenna. t Increase the separation between the equipment and receiver. t Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. t Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”

CE Mark WarningThis is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. National restrictions This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below: Country Restriction Reason/remark Bulgaria None General authorization required for outdoor use and public service France Outdoor use limited to 10 mW e.i.r.p. within the band 2454-2483.5 MHz Military Radiolocation use. Refarming of the 2.4 GHz band has been ongoing in recent years to allow current relaxed regulation. Full implementation planned 2012 Italy None If used outside of own premises, general authorization is required Luxembourg None General authorization required for network and service supply (not for spectrum) Norway Implemented This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund Russian Federation None Only for indoor applications Note: Please don’t use the product outdoors in France.

Chapter 4 Configuration for Windows Vista .................................................... 28Chapter 5 Configuration for Windows 7........................................................... 31Chapter 6 WPS configuration............................................................................ 336.1 PBC (Push Button Configuration) method......................................................................336.2 PIN method ....................................................................................................................356.2.1 Enter a PIN into your AP device..................................................................................... 366.2.2 Enter the PIN from your AP device................................................................................. 37Appendix A: Specifications ................................................................................... 38Appendix B: Glossary ............................................................................................ 39II

Package Contents The following contents should be found in your box: One ION-150,150Mbps Wireless N PCI-E Adapter Quick Installation Guide One Resource CD for ION-150, including: t Nexxt Solutions Wireless Client Utility (Nexxt) and Drivers t User Guide t Other Helpful Information Note:Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact with your distributor. Conventions:The ‘Adapter’ is used to designate the 150Mbps Wireless PCI-E Adapter, consecutively referredto in this guide simply as the ION-150.1

ION-150 150Mbps Wireless N PCI-E Adapter2Chapter 1 IntroductionThank you for choosing ION-150 ,150Mbps Wireless N PCI-E Adapter.1.1 Overview of the product The adapter is designed to provide a high-speed and unrivaled wireless performance for your PC. With a faster wireless connection, you can get a better Internet experience, such as downloading, gaming, video streaming and so on. The ION-150’s auto-sensing capability allows high packet transfer rate of up to 150Mbps for maximum throughput. It has good capability on anti-jamming; it can also interoperate with other wireless (802.11n/g/b) products. The adapter supports WEP, WPA and WPA2 encryption to prevent outside intrusion and protect your personal information from being exposed. The Quick Setup Wizard guides you step by step through the installation process; the Nexxt Solutions Wireless Client Utility helps you create a wireless connection immediately. With unmatched wireless performance, reception, and security protection, the ION-150 is the best choice for easily adding or upgrading wireless connectivity. 1.2 Features IEEE 802.11n, IEEE 802.11g, IEEE 802.11b standards Supports WPA/WPA2 data security, IEEE 802.1x authentication, TKIP/AES encryption, WEP encryption Make use of IEEE 802.11n wireless technology to provide a wireless data rate of up to 150Mbps Automacally adjusts to lower adjust to lower speeds due to distance or other operating limitations Provides PCI-E interface Supports Ad-Hoc and Infrastructure modes Good capability on anti-jamming Supports roaming between access points when configured in Infrastructure mode Easy to configure and provides monitoring information Supports Windows 2000/XP/Vista/7

3Note:This device leverages some 802.11n features to provide improved performance and coverage compared to 802.11a/g devices, and fully interoperates with 802.11n products if they are Wi-Fi CERTIFIED, but it does not conform to all of the requirements in the IEEE specification and is not classified as "n" in the Wi-Fi CERTIFIED program. 1.3 LED Status Status Working Status Off The driver has not been installed.Flashing Slowly The driver has been installed but there is no data being transmitted or received.Flashing Quickly There is data being transmitted or received.ION-1501 150Mbps Wireless N PCI-E Adapter

4Chapter 2 Installation Guide 2.1 Hardware Installation To install the adapter, follow these steps listed below: 1. Turn off your desktop PC and disconnect the AC power cable. 2. As soon as you remove the cover of your PC, locate an available PCI slot on the motherboard. Remove the metal slot cover on the back of the PC. Should you need further instructions, consult with your computer manufacturer.3. Slide the PCI-E Adapter into the PCI-E slot. Make sure that all of its pins are touching the slot's contacts. Once the adapter is firmly in place, secure its fastening tab to your PC's chassis with a mounting screw. Then, close your PC case. 4. Reconnect the AC power cable and turn your desktop PC back on.2.2 Software Installation 2.2.1 OverviewThe Adapter’s Setup Wizard will guide you through the Installation procedure for Windows XP. The Setup Wizard will install the Nexxt Solutions Wireless Client Utility (Nexxt) and drivers. When you install the hardware prior to installing the software, the system will prompt “Found New Hardware Wizard”, click Cancel, and run the Setup Wizard program on the CD-ROM. The Setup steps for Windows 2000 and XP are similar with each other. This user guide takes Windows XP for example. 2.2.2 Software Installation for Windows XP 1. Insert the Resource CD into your CD-ROM drive. To continue, find the CD/DVD drive where the installation CD is inserted. Open the ION-150 folder, and double-click on Setup.exe. Then the following screen for preparing setup will appear. ION-150 1150Mbps Wireless N PCI-E Adapter

ION-150 150Mbps Wreless N PCI-E Adapter5Figure 2-1 2. After a few seconds, Figure 2-2 will be displayed. Click Next to continue. Figure 2-2 3. After that, you should choose a Setup type. It is recommended that you select Install Client Utilities and Driver. Select Install Driver Only to install driver only, select Make Driver Installation Diskette(s) to make the diskette(s) as the installation driver (shown in Figure2-3). Click Next to continue.

6Figure 2-3 4. Click Browse to change the destination location for the software, then click Next in the screen below (shown in Figure 2-4).Figure 2-4 5. After that, select the program folder, you should create a new folder name or select one from the Existing Folders list. It is recommended that you keep the default setting. Click Next to continue the installation. ION-150 150Mbps Wireless N PCI-E Adapter

7Figure 2-5 6. Choose configuration tool, if unsure, leave default setting. Then click Next to continue. Figure 2-6 ION-150 150Mbps Wireless N PCI-E Adapter

87. Click OK to continue with the Installation. Wait a while for the setup as shown in Figure 2-7 .Figure 2-7 Note:For Windows XP, the Setup Wizard will notify you of how to proceed with the installation duringthese steps (shown in Figure 2-8). Our drivers have been tested thoroughly, and are able to work with the operating system. Click Continue Anyway to continue with the Installation. Figure 2-8 ION-150 150Mbps Wireless N PCI-E Adapter

98. After all all the steps detailed above have been completed, you will see following screen. Click Finish to reboot the system. Figure 2-9 2.2.3 Software Installation for Windows Vista 1. Insert the Resource CD into your CD-ROM drive. To continue, find the CD/DVD drive where the installation CD is inserted. Open ION-150 folder, and double-click Setup.exe. The following screen for preparing setup will now appear. ION-150 150Mbps Wireless N PCI-E Adapter

10Figure 2-10 2. After a few seconds, Figure 2-11 will be displayed. Click Next to continue. Figure 2-11 3. Click Yes to continue. ION-150 150Mbps Wireless N PCI-E Adapter

11Figure 2-12 4. The following page will be displayed. Please wait a moment. Figure 2-13 Note:For Windows Vista, the Setup Wizard will notify you of how to proceed with the installation duringthese steps (shown in Figure 2-14). Our drivers have been tested thoroughly, and are able to work with the operating system. Click Install this driver software anyway to continue with the Installation. ION-150 150Mbps Wireless N PCI-E Adapter

12Figure 2-14 5. Click Finish to complete the installation. Figure 2-15 2.2.4 Software Installation for Windows 7 1. Insert the Resource CD into your CD-ROM drive. To continue, find the CD/DVD drive where the installation CD has been inserted. Open ION-150 folder, and double-click Setup.exe. Then the following screen for preparing setup will appear. ION-150 150Mbps Wireless N PCI-E Adapter

13Figure 2-16 2. After a few seconds, Figure 2-17 will be displayed on the screen. Click Next to continue. Figure 2-17 3. Wait a while for the setup as shown in Figure 2-18.ION-150 150Mbps Wireless N PCI-E Adapter

14Figure 2-18 Note:For Windows 7, the Setup Wizard will notify you about the Windows Security with the installation during these steps (shown in Figure 2-19). Our drivers have been tested thoroughly, and are able to work with the operating system. Click Installation this driver software anyway to continue withthe installation.Figure 2-19 4. Then you will see Figure 2-20. Click Finish to complete. ION-150 150Mbps Wireless N PCI-E Adapter

15Figure 2-20 ION-150 150Mbps Wireless N PCI-E Adapter

16Chapter 3 Configuration for Windows XP ION-150 can be configured by Nexxt Solutions Wireless Client Utility (Nexxt) in Windows XP & 2000. This chapter describes how to configure your Adapter for wireless connectivity on your Wireless Local Area Network (WLAN) and use the data security encryption features. The configuration of the adapter in Windows XP is similar with that of Windows 2000. This User Guide takes Windows XP for example. noci yart s’retpadA eht ,dellatsni si retpada eht ecnO will appear in your system tray. It langis deviecer eht dna roloc gnisu htgnerts langis eht swohs dna ,neercs eht fo mottob eht ta sraeppastrength indication (RSSI). If the icon is gray, there is no connection. If the icon is red, there is poor signal strength and the RSSI is less than 5dB. If the icon is yellow, there is poor signal strength and the RSSI is between 5dB and 10dB. If the icon is green, there is good signal strength and the RSSI is between 10dB and 20dB. If the icon is green, there is excellent signal strength and the RSSI is more than 20dB. Double-click the icon and the utility will run. You can also run the utility by clicking the Startėė. The utility provides some integrated and easy tools to: Display current status information Edit and add configuration profiles Display current diagnostics information The above-mentioned capabilities are discussed in the following section.3.1 Current Status The Current Status tab contains general information about the program and its operations.No configuration is necessary for the Current Status tab.ION-150 retpadA E-ICP N sseleriW spbM051All programs Nexxt Solutions Nexxt Solutions Wireless Client Utility

21Figure 3-6 Power Save Mode - Please select the power save mode in the drop-down list.tMaximum - Selects maximum mode to let the access point buffer incoming messages for the Adapter. The Adapter will detect the access point if any messages are waiting periodically. tNormal - Normal mode uses maximum when retrieving a large number of packets, then switches back to power save mode after retrieving the packets. tOff - Turns power saving off, thus powering up the Wireless PCI-E Adapter continuously for a short message response time. Network Type: There are basically two modes of networking: tInfrastructure - All wireless clients will connect to an access point or wireless router. tAd-Hoc - Directly connecting to another computer, for peer-to-peer communication, using wireless network adapters on each computer, such as two or more ION-150 wireless adapters. Note:1) An Infrastructure network contains an Access Point or wireless router. All the wireless devices or clients will connect to the wireless router or access point. 2) An Ad-Hoc network contains only clients, such as laptops with wireless desktop adapters. All the adapters must be in Ad-Hoc mode to communicate.ION-150 150Mbps Wireless N PCI-E Adapter

22Wireless Mode: Specifies 2.4 GHz 150 Mbps, 2.4 GHz 54 Mbps or 2.4 GHz 11 Mbps operation in an access point network. The Wireless adapter must match the wireless mode of the access point with which it associates. Wireless Mode when Starting an Ad Hoc Network: Specifies 2.4 GHz 54/11 Mbps to start an Ad Hoc network if no matching network name is found after scanning all available modes. This mode also allows the selection of the channel that the Wireless Adapter uses. The channels available depend on the regulatory domain. If the adapter finds no other ad hoc adapters, the channel that the adapter starts the ad hoc network with will be selected automatically. The Adapter must match the wireless mode and channel of the clients it associates. 802.11 Authentication Mode: Selects which mode the Adapter uses to authenticate to an access point: tAuto - Automatic causes the adapter to attempt authentication using shared, but switches it to open authentication if shared fails. tOpen - Open System enables an adapter to attempt authentication regardless of its WEP settings. It will only associate with the access point if the WEP keys on both the adapter and the access point match. tShared - Shared-key only allows the adapter to associate with access points that have the same WEP key. For infrastructure (access point) networks, click Preferred APs… to specify four access points at most to the client adapter that attempts to be associated to the access points. The four access points have different priorities; starting with the first having the highest priority.Figure 3-7 ION-150 150Mbps Wireless N PCI-E Adapter

27Card Name - The name of the wireless network adapter. MAC Address - The MAC address of the wireless network adapter. Driver - The driver name and path of the wireless network adapter driver. Driver Version - The version of the wireless network adapter driver. Driver Date - The creation date of the wireless network adapter driver. Client Name - The name of the client computer.3.3.2 Check Receive and Transmit Statistical Information The Advanced Statistics show receiving and transmitting statistical information about the following receiving and transmitting diagnostics for frames received by or transmitted to the wireless network adapter. Figure 3-13 ION-150 150Mbps Wireless N PCI-E Adapter

28Chapter 4 Configuration for Windows Vista (Nexxt) is not available for Windows Vista. So after the Adapter's driver has been installed, we have to use Windows WLAN Autoconfig to establish a connection. Please follow the steps below. 1. Right-click the icon at the bottom of your screen in your system tray and then select “Connect to a network”. Figure 4-1 2. This page will then display and you will see the available wireless network list. Select the SSIDclick Connect. of your Access Point, run a test, for instance, to check the condition of the network and Figure 4-2 Select A Network ION-150 150Mbps Wireless N PCI-E AdapterNexxt Solutions Wireless Client Utility

293. Enter the passphrase, use 1234567890 for instance, and then click OK.Figure 4-3 Enter Passphrase 4. If the key entered is correct, you will successfully connect to the network. Figure 4-4 Connecting ION-150 150Mbps Wireless N PCI-E Adapter

305. Click Close to finish. Figure 4-5 successfully Connected ION-150 150Mbps Wireless N PCI-E Adapter

31Chapter 5 Configuration for Windows 7 (Nexxt) is not available for Windows 7. So after the Adapter's driver has been installed, we have to use Windows WLAN Autoconfig to establish a connection. Please follow the steps below. 1. Right-click the icon at the bottom of your screen in your system tray and then you will see the available wireless network list. Select the SSID of your Access Point, run a test, for instance, to check the condition of thenetwork and click Connect.Figure 5-1 Select A Network ION-150 150Mbps Wireless N PCI-E AdapterNexxt Solutions Wireless Client Utility

322. If your wireless network is secured, you will be required to enter the security key as shown in Figure 5-2. Enter the passphrase, use 1234567890 for instance, and then click OK.Figure 5-2 Enter Passphrase key entered is correct, you will successfully connect to the network as shown in Figure 5-3.3. If theFigure 5-3 Connecting ION-150 150Mbps Wireless N PCI-E Adapter

33Chapter 6 WPS configurationWPS (Wi-Fi Protected Setup) function allows you to add a new wireless device to an existing network quickly. Note:WPS function is not supported in Windows 7 OS. If the wireless Router supports Wi-Fi Protected Setup (WPS), you can establish a wireless connection between wireless adapter and router using either Push Button Configuration (PBC) method or PIN method. First, the WPS software should be installed. Insert the Resource CD into your CD-ROM drive, and open the folder named ION-150 . Double-click WPS.exe in the proper folder to start the installation, then the following screen for preparing setup will appear. Figure 6-1 Then, please follow the hint of the Operation System to complete the WPS installation. After that, WPS function can be enabled afterwards. We will explain here how to configure the WPS(we have used the Wireless Router of our company as an example of how to configure the WPS). 6.1 PBC (Push Button Configuration) method 1. Firstly, press the WPS button directly on the front panel of the Router shown in Figure 6-2.ION-150 150Mbps Wireless N PCI-E Adapter

34Figure 6-2 2. Double click the icon on the desktop to open the WPS Utility and then you can see the welcome screen shown as Figure 6-3. Click Next to continue. Figure 6-3 3. Then select Push the button on my access point in the next screen shown in Figure 6-4and click Next.ION-150 150Mbps Wireless N PCI-E Adapter

35Figure 6-4 4. Then wait a minute until Figure 6-5 appears. Click Finish to complete the WPS configuration. Figure 6-5 6.2 PIN method There are two ways to configure the WPS by PIN method:1 Enter a PIN into your AP device. ION-150 150Mbps Wireless N PCI-E Adapter

362 Enter the PIN from your AP device. You will find below the detailed configuration regarding each method.6.2.1 Enter a PIN into your AP device 1. Double click the icon on the desktop to open the WPS Utility and then you can see the welcome screen shown as Figure 6-3 period Click Next to continue. Figure 6-6 will appear. Select the second option and you will see the PIN value of the adapter which is randomly generated. Click Next.Figure 6-6 2. Open the Router’s Web-based Utility and click WPS link on the left of the main menu. Then Figure 6-7 will appear. Figure 6-7 3. Click Add device, then you can see Figure 6-8. Select Enter the new device’s PIN and ION-150 150Mbps Wireless N PCI-E Adapter

37enter the PIN value of the adapter shown in Figure 6-6, click Connect.Figure 6-8 4. When Figure 6-5 appears, the WPS configuration is complete. 6.2.2 Enter the PIN from your AP device 1. Open the WPS Utility and you will see Figure 6-3. Click Next to continue. Then Figure 6-9 will appear. Select the third option and enter the PIN value which is generally labeled on the bottom of the router. Click Next.Figure 6-9 2. When Figure 6-5 appears, the WPS configuration is complete. Note:If you generate a new PIN code for your Router, please enter the new one instead. ION-150 150Mbps Wireless N PCI-E Adapter

38Appendix A: Specifications NormalInterface PCI-E Interface Standards IEEE 802.11n; IEEE 802.11g; IEEE 802.11b; Operating System Windows 2000 / Windows XP / Windows Vista / Windows 7 Radio Data Rate 11b: 1/2/5.5/11Mbps 11g: 6/9/12/18/24/36/48/54Mbps 11n: Up to 150Mbps Modulation11b: CCK, QPSK, BPSK; 11g: OFDM; 11n: QPSK, BPSK, 16-QAM, 64-QAM;Media Access Protocol CSMA/CA with ACK Data Security WPA/WPA2; 64/128/152-bit WEP; TKIP/AES Spread Spectrum Direct Sequence Spread Spectrum (DSSS) Safety & Emissions FCC, CE Environmental and Physical Operating Temp. 0ºC~40º-40ºF~158ºF)32º F~104C (Storage Temp. -40ºC~ 70º ºF)CAmbient Humidity 10% ~ 90% RH, Non-condensing Storage Humidity 5% ~ 90% RH, Non-condensing ION-150 retpadA E-ICP N sseleriW spbM051(

39Appendix B: Glossary 802.11b - The 802.11b standard specifies a wireless product networking at 11 Mbps using direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2.4GHz, and WEP encryption for security. 802.11b networks are also referred to as Wi-Fi networks. 802.11g - specification for wireless networking at 54 Mbps using direct-sequence spread-spectrum (DSSS) technology, using OFDM modulation and operating in the unlicensed radio spectrum at 2.4GHz, and backward compatibility with IEEE 802.11b devices, and WEP encryption for security. Ad-hoc Network - An ad-hoc network is a group of computers, each with a Wireless Adapter, connected as an independent 802.11 wireless LAN. Ad-hoc wireless computers operate on a peer-to-peer basis, communicating directly with each other without the use of an access point. Ad-hoc mode is also referred to as an Independent Basic Service Set (IBSS) or as peer-to-peer mode, and is useful at a departmental scale or SOHO operation. DSSS - (Direct-Sequence Spread Spectrum) - DSSS generates a redundant bit pattern for all data transmitted. This bit pattern is called a chip (or chipping code). Even if one or more bits in the chip are damaged during transmission, statistical techniques embedded in the receiver can recover the original data without the need of retransmission. To an unintended receiver, DSSS appears as low power wideband noise and is rejected (ignored) by most narrowband receivers. However, to an intended receiver (i.e. another wireless LAN endpoint), the DSSS signal is recognized as the only valid signal, and interference is inherently rejected (ignored). FHSS - (Frequency Hopping Spread Spectrum) - FHSS continuously changes (hops) the carrier frequency of a conventional carrier several times per second according to a pseudo-random set of channels. Because a fixed frequency is not used, and only the transmitter and receiver know the hop patterns, interception of FHSS is extremely difficult. Infrastructure Network - An infrastructure network is a group of computers or other devices, each with a Wireless Adapter, connected as an 802.11 wireless LAN. In infrastructure mode, the wireless devices communicate with each other and to a wired network by first going through an access point. An infrastructure wireless network connected to a wired network is referred to as a Basic Service Set (BSS). A set of two or more BSS in a single network is referred to as an Extended Service Set (ESS). Infrastructure mode is useful at a corporation scale, or when it is necessary to connect the wired and wireless networks. Spread Spectrum - Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband transmission, but the trade off produces a signal that is, in effect, louder and thus easier to detect, provided that the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is ION-150 150Mbps Wireless N PCI-E Adapter

40not tuned to the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives, Direct Sequence Spread Spectrum (DSSS) and Frequency Hopping Spread Spectrum (FHSS). SSID - AService Set Identification is a thirty-two character (maximum) alphanumeric key identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID. This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the wireless Access Point and to the wireless network name. See also Wireless Network Name and ESSID. WEP - (Wired Equivalent Privacy) - A data privacy mechanism based on a 64-bit or 128-bit or 152-bit shared key algorithm, as described in the IEEE 802.11 standard. To gain access to a WEP network, you must know the key. The key is a string of characters that you create. When using WEP, you must determine the level of encryption. The type of encryption determines the key length. 128-bit encryption requires a longer key than 64-bit encryption. Keys are defined by entering in a string in HEX (hexadecimal - using characters 0-9, A-F) or ASCII (American Standard Code for Information Interchange – alphanumeric characters) format. ASCII format is provided so you can enter a string that is easier to remember. The ASCII string is converted to HEX for use over the network. Four keys can be defined so that you can change keys easily. Wi-Fi - A trade name for the 802.11b wireless networking standard, given by the Wireless Ethernet Compatibility Alliance (WECA, see http://www.wi-fi.net), an industry standards group promoting interoperability among 802.11b devices. WLAN - (Wireless Local Area Network) - A group of computers and associated devices communicate with each other wirelessly, which network serving users are limited in a local area.WPA - (Wi-Fi Protected Access) - A wireless security protocol use TKIP (Temporal Key Integrity Protocol) encryption, which can be used in conjunction with a RADIUS server. ION-150 150Mbps Wireless N PCI-E Adapter

Navigation menu